WOMA Accessories Surface Cleaning
2015
1 FLOOR CLEANING 3
1.1 FLOORMASTER FM 1000-E-24V 3 1.2 VACUJET VJ 2500-1-E 4 1.3 HOSE LINES 5
1.3.1 UP TO 1500 BAR 5 1.3.2 UP TO 3010 BAR 10
2 WALL CLEANING 14 2.1 ECO TOP ROTATING CLEANER 14
2.1.1 ETRC 2500-E-EXI-F / 24V-F 14 2.2 MAGNETIC LIZARD M2500-E-24V 16 2.3 HOSE LINES 20
2.3.1 UP TO 3010 BAR 20
3 WHIRL DISCS 28 3.1 WHIRL DISC 400 AND 750 BAR 28
4 NOZZLE INSERT 29 4.1 UP TO 1500 BAR 29
4.1.1 ROUND JET NOZZLE FORM 4 29 4.1.2 FLAT JET NOZZLE FORM 19 33
4.2 UP TO 3000 BAR 40 4.2.1 ROUND JET NOZZLE FORM 21 LL – LONG LIFE 40 4.2.2 ROUND JET NOZZLE FORM 21 S – SAPHIR 44
5 ELECTRIC ACCESSORIES 48
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 3
1 FLOOR CLEANING
1.1 FloorMaster FM 1000-E-24V
Description:
The FloorMaster is intended for the use as floor cleaning unit which, in connection with a suction device, cleans and disposes simultaneously in a nonpolluting way. The high temperature resistant up to 100°C
makes the FloorMaster in connection with
WOMA Ecotherm units to an extremely efficient water tool. Advantages: When using a suction device a separate disposal of suspension risen from cleaning is not necessary. Height adjustment for spray bar Speed control by nozzle adjustment
Technical data: Material-No.: 6.025-260.0 Operating pressure: max.1000 bar Medium temperature: max.100°C Weight: appr. 23 kg Working widt: appr. 300 mm Speed spray bar: max .1500 1/min No. of nozzle: 2 pieces Recommended nozzles: Form 4 round jet or Form19 fan jet High pressure connection: aM24x1,5 24°DK Control voltage: 24 V DC
Accessories: High pressure connection aM22x1,5 WGA MN 9.894-356.0 WGA = special hand-screwed connection
Recommended nozzle diameter at: 600 bar and 28 l/min 2 x 0,90 mm Form 4 ° MN 6.025-470.0 2 x 1,10 mm Form 19 30° MN 6.025-467.0 800 bar and 21 l/min 2 x 0,70 mm form 4 MN 9.885-950.0 2 x 0,80 mm form 19 30° MN 9.886-186.0 O-ring for nozzle form 4 and 19 MN 6.025-168.0
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 4
1.2 Vacujet VJ 2500-1-E for electric control
Vacujet 2500-1-E-EXI MN 9.871-082.0 with sealing lip Vacujet 2500-1-E-EXI MN 9.871-083.0 with brush Vacujet 2500-1-E-24V MN 9.907-562.0 with sealing lip Vacujet 2500-1-E-24V MN 9.871-094.0 with brush Description:
The Vacujet 2500-1-E is intended for the use as floor cleaning unit which, in connection with a suction device, cleans and disposes simultaneously in a non-polluting way.
Depending on requirement to the ground sealing the Vacujet can be equipped with a brush or in case of highest requirements to density with a sealing lip.
Advantages:
When using a suction device a separate disposal of suspension risen from cleaning is not necessary.
Speed adjustable by air pressure and air quantity
Parts under pressure made of high-tensile stainless steel
Optimum jet stream when using nozzle form 21 LL (LL = LongLife) see product sheet D-21LL-3000
Operating information:
The air motor is only to be used with dry, clean and lubricated air.
We recommend WOMA pressurized air maintenance unit MN 9.872-124.0.
Technical data: Operating pressure: Overall width: Working width: Weight: Speed Spray bar: Air consumption: Air pressure: No. of nozzles: Recommended nozzles:
max 2500 bar appr. 440 mm appr. 225 mm appr. 36,0 kg max. 2500 1/min max. 0,52m
3/min at 6 bar
max. 7 bar max. 8 pieces
form 21 LL and form 21 Sapphire
Recommended nozzle diameters at:
2500 bar and 20 l/min 4 x 0,25 mm form 21 LL MN 6.025-238.0 and 4 x 0,30 mm form 21 LL MN 6.025-248.0 * When using nozzle form 21 Sapphire, the
nozzle diameters must be 0.05 mm larger than that of nozzle form 21 LL.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 5
1.3 Hose Lines 1.3.1 Up to 1500 bar 1.3.1.1 Very hight pressure hose DN 12 – HST4K Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 1100 bar
max. 15950 psi
1650 bar
23925 psi
Alle WOMA Produkte
All WOMA products
Aufbau:
Schlauchseele aus Polyamid Druckträger aus zwei Wickellagen und zwei offenen Wickellagen Stahldraht hoher Zugfestigkeit Oberdecke aus Polyurethan Temperaturbereich: -10°C bis +70°C Construction:
Polyamide inner tube Reinforcement of two spiral layers and two open layers of high tensile steel wire Polyurethane cover Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Material-No.
Inner-Ø
DN mm
Outer-Ø
mm
Bendradius
R = mm
Weight
kg/m
max. delivery length
m
9.913-833.0
5
4,6
9.913-834.0
10
8,6
9.913-850.0
13,0
23,0
100
0,80
100
9.913-835.0
20
16,6
Thread M as per DIN 13 / ISO 261
Besondere Vorteile:
geringes Gewicht und kleiner Biegeradius, daher besonders zu empfehlen als Pistolenschlauch.
Special advantages:
low weight and a small bend radius; therefore especially recommended as gun hose
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 6
Hose fittings and accessories DN 12 – HST4K
Swivel fitting
Hose connector
Material-No.
Material
L 1
mm
SW 1
Width across
flats
mm
O-Ring
Material-No.
Material-No.
L 2
mm
L 3
mm
SW 2
mm
Material
9.913-848.0
Steel
89
30
6.025-315.0
9.877-911.0
65
20
32
NIRO / SS
45º Elbow
90º Elbow
Material-No.
Material
L 4
mm
L 5
mm
SW 3
mm
O-Ring
Material-No
Material-No.
Material
L 6
mm
L 7
mm
SW 4
mm
O-Ring
Material-No.
9.887-325.0
Steel
100
43
30
9.882-191.0
9.887-324.0
Steel
77
76
30
9.882-191.0
Thread M as per DIN 13 / ISO 261 NIRO = nichtrostender Stahl , SS = Stainless Steel
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 7
1.3.1.2 Very high pressure hose DN 12 – HST4G – SR3
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 1100 bar
max. 15950 psi
1650 bar
23925 psi
Alle WOMA Produkte
All WOMA products
Aufbau :
Schlauchseele aus synthetischem Gummi Druckträger aus vier Draht-Spirallagen. Oberdecke aus synthetischem Gummi Temperaturbereich: -10°C bis +80°C Construction :
Synthetic rubber inner tube 4 spiralwire reinforcement Synthetic rubber cover Operating temperature range: -10°C to +80°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Equipped with fittings
Material
Material-No.
Inner-φ
φ i
mm
Outer-φ
φ a
mm
Bendradius
R = mm
Weight
kg/m
max. delivery length
m
9.887-887.0
10
14,9
Steel
9.887-888.0
20
28,8
Steel
9.887-890.0
12,7
27,0
250
1,39
40
9.887-889.0
40
56,6
Steel
Thread M as per DIN 13 / ISO 261
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 8
Hose fittings and accessories DN 12 – HST4G – SR3
Swivel fitting
Hose connector
Material-No.
Material
L 1
mm
SW 1
Width across flats
mm
O-Ring
Material-No.
Part-No.
L 2
mm
L 3
mm
SW 2
mm
Material
9.887-891.0
Stahl / Steel
110
30
6.025-315.0
9.877-911.0
65
20
32
NIRO / SS
45º Elbow
90º Elbow
Material-No.
Material
L 4
mm
L 5
mm
SW 3
mm
O-Ring
Material-No.
Material-No.
Material
L 6
mm
L 7
mm
SW 4
mm
O-Ring
Material-No.
9.887-325.0
9.887-329.0
Steel
NIRO / SS
100
43
30
9.882-191.0
9.887-324.0
9.887-328.0
Steel
NIRO / SS
77
76
30
9.882-191.0
Thread M as per DIN 13 / ISO 261; NIRO = nichtrostender Stahl , SS = Stainless Steel
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 9
1.3.1.3 Very high pressure hose DN 10 - HST4G - H for hot water application up to 100° C Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Temperaturbereich
Operating temperature range
Verwendung für
To use for
:
:
:
:
:
:
:
:
max. 1250 bar
max. 18120 psi
1875 bar
27190 psi
-10° C bis +100° C
-10° C to +100° C
Ecotherm 800
Ecotherm 800
Aufbau :
Schlauchseele aus hochtemperaturbeständigem synthetischem Gummi Druckträger aus vier Draht-Spirallagen Oberdecke aus synthetischem Gummi Construction :
High temperature resistent synthetic rubber tube 4-spiralwire reinforcement Cover of synthetic rubber
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Equipped with
fittings
Material
Inner-Ø Ø i
mm
Outer-Ø
Ø a
mm
Bend-radius
R = mm
Weight
kg/m
max. delivery length
m
9.887-566.0 20 17,3
9.909-769.0 30 25,8 Steel/ 10 21,4 150 0,85 100
9.910-972.0 40 34,3 galvanized
Gewinde M nach DIN 13 / ISO 261; thread M as per DIN 13 / ISO 261 For sealing cone 24° Hose connector: TN / PN 9.877-911.0 O-Ring: MN / MN 6.025-314.0
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 10
1.3.2 Up to 3010 bar 1.3.2.1 Very high pressure hose DN8-HST6K-9/16UNF-LH
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 3010
max. 43645
4515
65470
Alle WOMA-Produkte
All WOMA products
bar
psi
bar
psi
Aufbau :
Schlauchseele aus Polyoxymethylen Druckträger aus sechs Drahtlagen Oberdecke aus Polyamid, rot Temperaturbereich: -10°C bis +70°C
Construction:
Polyoxmethylene inner tube 6 wire reinforcement Cover of Polyamide, rot Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Thread
A
Inner diameter
mm
Outer diameter
mm
Bendradius
mm
Weight
kg/m
max. delivery length
m
9.915-135.0 2 2,5
9/16-18
UNF-LH
9.915-136.0 5 5,0
9.915-137.0 10 9,1 7,8 17,3 230 0,83 300
9.915-138.0 20 17,4
9.915-139.0 40 34,0
Restraining attachment for strain relief devices see product sheet Z-025 Hose tubes with protective hose see product sheet S-008-3010-9/16-S
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 11
Accessories DN 8 – HST6K – 9/16 LH 1 2 3
Hose connector Material: Stainless steel
Connection cpl.
d HP
Pipe AD
Max.
Operating pressure
Dimensions in mm
1
Connector
body
2
Pressure
screw
3
Pressure
ring
2
Torque
Material-No. mm inch mm bar C SW HEX
Nm
9.883-668.0
9/16-18 UNF LH
5 9/16 14,30 4000 56 32 9.884-059.0
i 1 1/8-12
UNF
9.883-669.0
1 1/8-12
UNF
9.883-670.0
9/16-18 UNF LH
160
Mounting Instructions Pressure body, e.g. hose connector, pressure flanges, gun connection etc. One to two threads must be visible Pressure ring Pressure screw Hose nipple/pipe
Slide the pressure screw on to the hose nipple/end of the pipe.
Screw the pressure ring on to the pipe until one to two threads are to be seen behind the sealing cone.
Lubricate the thread of the pressure screw with anti-seize mounting paste (Material-No. 9.892-362.0).
Slip the pressure screw over the pressure ring and screw it into the pressure body.
Tighten pressure screw with tightening torque (see table).
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 12
1.3.2.2 Very high pressure hose DN8-HST6K-9/16UNF-LH-S
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 3010
max. 43645
4515
65470
Alle WOMA-Produkte
All WOMA products
bar
psi
bar
psi
Aufbau :
Schlauchseele aus Polyoxymethylen Druckträger aus sechs Drahtlagen Oberdecke aus Polyamid, rot Temperaturbereich: -10°C bis +70°C
Construction:
Polyoxmethylene inner tube 6 wire reinforcement Cover of Polyamide, rot Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Thread
A
Inner diameter
mm
Outer diameter
mm
Bendradius
mm
Weight
kg/m
max. delivery length
m
9.915-143.0 10 12,1 9/16-18
UNF-LH
9.915-144.0 20 23,4 7,8 17,3 230 0,83 300
9.915-145.0 40 46,0
Restraining attachment for strain relief devices see product sheet Z-025 Hose tubes without protective hose see product sheet S-008-30100-9/16
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 13
Accessories DN 8 – HST6K – 9/16 LH 1 2 3
Hose connector Material: Stainless steel
Connection cpl.
d
Rohr AD Pipe AD
Max.
Operating pressure
Dimensions in mm
1
Connector
body
2
Pressure
screw
3
Pressure
ring
2
Torque
Material-Nr. Material-No.
mm Zoll inch
mm bar C SW HEX
Nm
9.883-668.0
9/16-18 UNF LH
5 9/16 14,30 4000 56 32 9.884-059.0
i 1 1/8-12
UNF
9.883-669.0
1 1/8-12
UNF
9.883-670.0
9/16-18 UNF LH
160
Mounting Instructions Pressure body, e.g. hose connector, pressure flanges, gun connection etc. One to two threads must be visible Pressure ring Pressure screw Hose nipple/pipe
Slide the pressure screw on to the hose nipple/end of the pipe.
Screw the pressure ring on to the pipe until one to two threads are to be seen behind the sealing cone.
Lubricate the thread of the pressure screw with anti-seize mounting paste (Material-No. 9.892-362.0).
Slip the pressure screw over the pressure ring and screw it into the pressure body.
Tighten pressure screw with tightening torque (see table).
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 14
2 WALL CLEANING 2.1 Eco Top Rotating Cleaner
2.1.1 ETRC 2500-E-EXI-F / 24V-F
for electric control with air motor
Description: The ETRC 2500-E-EXI-F / -24V-F is a high production hand held tool for the cleaning and removal of paint coatings from large flat areas. The ETRC version „F“ (air motor driven) gives the operator the flexibility of varying the RPMs of the rotary tool independent of orifice size. With this feature the user more efficiently utilizes the energy of the jets maximizing production and quality of the prepared surface. Advantages: The ETRC is delivered vacuum ready for full recovery of water and debris eliminating environmental concerns. All parts subject to pressure are made of high-tensile. stainless steel. Optimum jet stream when using nozzle form 21LL (LL=LongLife) see product sheet D-21LL-3000.
Technical data: ETRC 2500-E-24V-F Material-No. ETRC 2500-E-EXI-F Material-No. Operating pressure max. Working width appr. Weight appr. Rotating speed max. Air consumption Air pressure max. No. of nozzles max. High pressure connection
9.871-115.0
9.871-116.0
2500 bar
180 mm
9,4 kg
2500 rpm
3,6l at 6 bar 7 bar
4 pieces
9/16-18 UNF-LH
Operating information: The rotary operation is not supposed to run without water for longer than 15 sec.
Recommended nozzle diameters at: 2500 bar and 20 l/min 4 x 0,40mm Form 21LL MN 6.025-240.0 When using nozzle form 21 sapphire, the nozzle diameters must be 0.05mm larger than that of nozzle form 21 LL.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 15
Eco Top Rotating Cleaner Accessories
Description: The balancer (Weight counter balance) extends from a cable reel. This cable reel provides constant tension on the entire cable length so that the ETRC is maintained in the desired position. By using the balancer the operator can work effortlessly for long periods. Advantages: The automatic locking device has a premature retraction stop at predetermined positions, when the ETRC is slowly retracted. The locking device is not actuated, when the ETRC is retracted quickly. An increase in production is obtained, since the ETRC does not need to be returned to its home position between operational steps.
Technical data:
Balancer Material-No.
9.884-180.0
Load 9 – 14 kg Wire rope lenght 2000 mm Weight 3,6 kg
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 16
2.2 Magnetic Lizard M2500-E-24V
Portable operating desk
Description: The Magnetic Lizard M2500 is specially designed for semi-automatic cleaning / stripping of vertical surfaces such as ship hulls, storage tanks and large steel-structures. The Magnetic Lizard M2500 is a self propelled cleaning system which is adhered onto the surface via permanent magnet. Advantages:
Flexible driving units enable to treat bent steel surfaces
Increase of efficiency possible by adding further water tools
Speed regulation via potentiometer
Technical data: Operating pressure: HP connection: Suction connection: Working width-Standard: Working width: Weight:
Driving speed: Speed spray bar: Adhesive force: Air consumption: compressed air free of oil and filtered 5my: Air pressure:
Board voltage: Insulation class: No. of nozzles: Recommended nozzles:
max. 2500 bar 9/16-18 UNF-LH
DN 50 mm appr. 250 mm max. 400 mm
appr. 55 kg
0 – 8m/min
max. 2500 1/min 10 KN at 3 mm
surface distance
1,5m3/min at 6 bar
max. 8 bar
24V DC IP 65
max.8 pieces * form 13 / form 21
Accessories: Safety Winch with 30 m stainless steel cable Material No.: 9.909-460.0
Recommended nozzle diameters at: 2500 bar and 20 l/min 8 x 0,30 mm form 21 MN 9.886-208.0 2500 bar and 40 l/min 8 x 0,40 mm form 21 MN 6.025-220.0 * When using nozzle form 13, 8 nozzle holding screws MN 9.875-795.0 have to be ordered separately.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 17
FLOW CHART Magnetic Lizard M2500-E-24V High pressure unit control - EXI
Power supply 24V for Lizard
9.889-439.0
High pressure unit Control
EXI
Cable drum 50 m 24V
9.890-410.0
Cable drum 50 m EXI
9.890-411.0
Operating desk 24V / EXI
9.910-192.0
Cable drum 50 m 24V 10-pin 9.889-440.0
Magnetic-Lizard M2500 – E - 24V
9.893-693.0
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 18
FLOW CHART Magnetic Lizard M2500-E-24V High pressure unit control - 24V DC
High pressure unit Control 24V DC
Cable drum 50 m 24V
9.890-410.0
Operating desk 24V / EXI
9.910-192.0
Cable drum 50 m 24V DC – 10-pin
9.889-440.0
Magnetic Lizard M2500 – E – 24V
9.893-693.0
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 19
Connecting scheme Lizard
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 20
2.3 Hose Lines 2.3.1 Up to 3010 bar 2.3.1.1 Very high pressure hose DN5-HST6K-9/16UNF-LH
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
max. 3010
max. 43645
4515
65470
Alle WOMA-Produkte
All WOMA products
bar
psi
bar
psi
Aufbau :
Schlauchseele aus Polyoxymethylen Druckträger aus sechs Drahtlagen Oberdecke aus Polyamid, blau Temperaturbereich: -10°C bis +70°C
Construction:
Polyoxmethylene inner tube 6 wire reinforcement Cover of Polyamide, blue Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Thread
A
Inner diameter
mm
Outer diameter
mm
Bendradius
mm
Weight
kg/m
max. delivery length
m
9.915-150.0 5 3,0 9/16-18
UNF-LH
9.915-151.0 10 5,3 4,8 13,3 200 0,47 300
9.915-152.0 20 10,0
Restraining attachment for strain relief devices see product sheet Z-025 Hose tubes with protective hose see product sheet S-005-3010-9/16-S
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 21
Accessories DN 5 – HST6K – 9/16 LH 1 2 3
Hose connector Material: Stainless steel
Connection cpl.
d HP
Pipe AD
Max.
Operating pressure
Dimensions in mm
1
Connector
body
2
Pressure
screw
3
Pressure
ring
2
Torque
Material-No. mm Zoll inch
mm bar C SW HEX
Nm
9.883-668.0
9/16-18 UNF LH
5 9/16 14,30 4000 56 32 9.884-059.0
i 1 1/8-12
UNF
9.883-669.0
1 1/8-12
UNF
9.883-670.0
9/16-18 UNF LH
160
Mounting Instructions . Pressure body, e.g. hose connector, pressure flanges, gun connection etc. One to two threads must be visible Pressure ring Pressure screw Hose nipple/pipe
Slide the pressure screw on to the hose nipple/end of the pipe.
Screw the pressure ring on to the pipe until one to two threads are to be seen behind the sealing cone.
Lubricate the thread of the pressure screw with anti-seize mounting paste (Material-No. 9.892-362.0).
Slip the pressure screw over the pressure ring and screw it into the pressure body.
Tighten pressure screw with tightening torque (see table).
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 22
2.3.1.2 Very high pressure hose DN5-HST6K-9/16UNF-LH-S
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 3010
max. 43645
4515
65470
Alle WOMA-Produkte
All WOMA products
bar
psi
bar
psi
Aufbau :
Schlauchseele aus Polyoxymethylen Druckträger aus sechs Drahtlagen Oberdecke aus Polyamid, blau Temperaturbereich: -10°C bis +70°C
Construction:
Polyoxmethylene inner tube 6 wire reinforcement Cover of Polyamide, blue Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Thread
A
Inner diameter
mm
Outer diameter
mm
Bendradius
mm
Weight
kg/m
max. delivery length
m
9.915-155.0 5 4,0 9/16-18
UNF-LH
9.915-156.0 10 7,3 4,8 13,3 200 0,47 300
9.915-157.0 20 14,0
Restraining attachment for strain relief devices see product sheet Z-025 Hose tubes without protective hose see product sheet S-005-3010-9/16
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 23
Accessories DN 5 – HST6K – 9/16 LH 1 2 3
Hose connector Material: Stainless steel
Connection cpl.
d HP
Pipe AD
Max.
Operating pressure
Dimensions in mm
1
Connector
body
2
Pressure
screw
3
Pressure ring
2
Torque
Material-No. mm Zoll inch
mm bar C SW HEX
Nm
9.883-668.0
9/16-18 UNF LH
5 9/16 14,30 4000 56 32 9.884-059.0
i 1 1/8-12
UNF
9.883-669.0
1 1/8-12
UNF
9.883-670.0
9/16-18 UNF LH
160
Mounting Instructions Pressure body, e.g. hose connector, pressure flanges, gun connection etc. One to two threads must be visible Pressure ring Pressure screw Hose nipple/pipe
Slide the pressure screw on to the hose nipple/end of the pipe.
Screw the pressure ring on to the pipe until one to two threads are to be seen behind the sealing cone.
Lubricate the thread of the pressure screw with anti-seize mounting paste (Material-No. 9.892-362.0).
Slip the pressure screw over the pressure ring and screw it into the pressure body.
Tighten pressure screw with tightening torque (see table).
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 24
2.3.1.3 Very high pressure hose DN8-HST6K-9/16UNF-LH
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 3010
max. 43645
4515
65470
Alle WOMA-Produkte
All WOMA products
bar
psi
bar
psi
Aufbau :
Schlauchseele aus Polyoxymethylen Druckträger aus sechs Drahtlagen Oberdecke aus Polyamid, rot Temperaturbereich: -10°C bis +70°C
Construction:
Polyoxmethylene inner tube 6 wire reinforcement Cover of Polyamide, rot Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Thread
A
Inner diameter
mm
Outer diameter
mm
Bendradius
mm
Weight
kg/m
max. delivery length
m
9.915-135.0 2 2,5
9/16-18
UNF-LH
9.915-136.0 5 5,0
9.915-137.0 10 9,1 7,8 17,3 230 0,83 300
9.915-138.0 20 17,4
9.915-139.0 40 34,0
Restraining attachment for strain relief devices see product sheet Z-025 Hose tubes with protective hose see product sheet S-008-3010-9/16-S
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 25
Accessories DN 8 – HST6K – 9/16 LH 1 2 3
Hose connector Material: Stainless steel
Connection cpl. d HP
Pipe AD
Max. Operating pressure Dimensions in mm
1
Connector
body
2
Pressure
screw
3
Pressure
ring
2
Torque
Material-No. mm inch mm bar C SW HEX
Nm
9.883-668.0
9/16-18 UNF LH
5 9/16 14,30 4000 56 32 9.884-059.0
i 1 1/8-12
UNF
9.883-669.0
1 1/8-12
UNF
9.883-670.0
9/16-18 UNF LH
160
Mounting Instructions Pressure body, e.g. hose connector, pressure flanges, gun connection etc. One to two threads must be visible Pressure ring Pressure screw Hose nipple/pipe
Slide the pressure screw on to the hose nipple/end of the pipe.
Screw the pressure ring on to the pipe until one to two threads are to be seen behind the sealing cone.
Lubricate the thread of the pressure screw with anti-seize mounting paste (Material-No. 9.892-362.0).
Slip the pressure screw over the pressure ring and screw it into the pressure body.
Tighten pressure screw with tightening torque (see table).
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 26
2.3.1.4 Very high pressure hose DN8-HST6K-9/16UNF-LH-S
Betriebsdruck
Operating pressure
Prüfdruck
Test pressure
Verwendung für
To use for
:
:
:
:
:
:
max. 3010
max. 43645
4515
65470
Alle WOMA-Produkte
All WOMA products
bar
psi
bar
psi
Aufbau :
Schlauchseele aus Polyoxymethylen Druckträger aus sechs Drahtlagen Oberdecke aus Polyamid, rot Temperaturbereich: -10°C bis +70°C
Construction:
Polyoxmethylene inner tube 6 wire reinforcement Cover of Polyamide, rot Operating temperature range: -10°C to +70°C
Hose tubes
Hose per metre
Material-No.
Nominal length
L = m
Weight
kg
Thread
A
Inner diameter
mm
Outer diameter
mm
Bendradius
mm
Weight
kg/m
max. delivery length
m
9.915-143.0 10 12,1 9/16-18
UNF-LH
9.915-144.0 20 23,4 7,8 17,3 230 0,83 300
9.915-145.0 40 46,0
Restraining attachment for strain relief devices see product sheet Z-025 Hose tubes without protective hose see product sheet S-008-30100-9/16
Accessories DN 8 – HST6K – 9/16 LH
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 27
1 2 3
Hose connector Material: Stainless steel
Connection cpl.
d HP
Pipe AD
Max.
Operating pressure
Abmessungen in mm Dimensions in mm
1
Connector
body
2
Pressure
screw
3
Pressure ring
2
Torque
Material-No.
mm inch mm bar C SW HEX
Nm
9.883-668.0
9/16-18 UNF LH
5 9/16 14,30 4000 56 32 9.884-059.0
i 1 1/8-12
UNF
9.883-669.0
1 1/8-12
UNF
9.883-670.0
9/16-18 UNF LH
160
Mounting Instructions Pressure body, e.g. hose connector, pressure flanges, gun connection etc. One to two threads must be visible Pressure ring Pressure screw Hose nipple/pipe
Slide the pressure screw on to the hose nipple/end of the pipe.
Screw the pressure ring on to the pipe until one to two threads are to be seen behind the sealing cone.
Lubricate the thread of the pressure screw with anti-seize mounting paste (Material-No. 9.892-362.0).
Slip the pressure screw over the pressure ring and screw it into the pressure body.
Tighten pressure screw with tightening torque (see table).
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 28
3 WHIRL DISCS 3.1 Whirl disc 400 and 750 bar
Description: The whirl disc has been developed for a variety of surface cleaning tasks and it stands out for its high efficiency in cleaning large areas within a short time and at little expenditure of energy. This is achieved by a nozzle carrier head which is slipped on to a carrier axle and which, owing to the reaction force of the high-pressure water, rotates about its longitudinal axis at a speed of several thousand revolutions per minute. For determining the nozzle diameter 10 %leakage water must be taken into consideration. Owing to the wear occurring in the course of the time, the nozzle head shaft and the nozzle carrier head can only be replaced together because they are both affected to more or less the same extent. In such a case, the replacement assembly group MN 9.893-780.0, consisting of a nozzle head shaft, nozzle carrier head, sealing ring and protecting plug, must be ordered. Furthermore, the sealing ring MN 9.881-592.0-must be replaced when the nozzle head shaft has been looser. Accessories: 2 x Round jet nozzles form 4 2 x Flat jet nozzles form 19 (only without cover hood) 2 x O-ring Material-No.: 6.025-168.0 Slotted nut spanner for nozzle holding screws Material-No.: 9.883-469.0
Technical Data: Whirl disc with cover hood 400 bar Material-No.: 9.886-570.0 Weight: appr. 0,82 kg Whirl disc without cover hood 400 bar Material-No.: 9.886-569.0 Weight: appr. 0,61 kg Whirl disc with cover hood 750 bar Material-No.: 9.909-595.0 Weight: appr. 1,4 kg Whirl disc without cover hood 750 bar Material-No.: 9.886-572.0 Weight: appr. 1,2 kg Operating pressure: max. 400 bar or 750 bar Flow volume: 100 l/min at 400 bar 70 l/min at 750 bar Spraying range: 100mm at 20mm distance 400mm at 170mm distance Flow medium: Water Pressure connection: female G 3/8
Whirl disc without cover hood
Whirl disc with cover hood
Fe
male
G 3
/8
Nozzle form 4 or 19
Nozzle carrier head
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 29
4 NOZZLE INSERT 4.1 Up to 1500 bar
4.1.1 Round jet nozzle Form 4
Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0 Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,50 2,1 2,6 3,0 3,4 3,7 4,0 4,1 4,2 4,5 4,7 5,0 5,2 5,4 5,6 5,8
9.885-948.0 7 11 14 18 21 25 26 28 32 35 39 42 46 49 53
0,60 3,1 3,7 4,3 4,8 5,3 5,7 5,9 6,1 6,5 6,8 7,2 7,5 7,8 8,1 8,4
9.885-953.0 10 15 20 25 30 35 38 40 45 50 55 60 66 71 76
0,70 4,2 5,1 5,9 6,6 7,2 7,8 8,0 8,3 8,8 9,3 9,7 10,2 10,6 11,0 11,4
9.885-950.0 14 21 27 34 41 48 51 55 62 69 75 82 89 96 103
0,80 5,4 6,6 7,7 8,6 9,4 10,2 10,5 10,9 11,5 12,1 12,7 13,3 13,8 14,4 14,9
6.025-200.0 18 27 36 45 54 63 67 72 81 90 99 108 117 125 134
0,85 6,1 7,5 8,7 9,7 10,6 11,5 11,9 12,3 13,0 13,7 14,4 15,0 15,6 16,2 16,8
9.886-902.0 20 30 40 51 61 71 76 81 91 101 111 121 132 142 152
0,90 6,9 8,4 9,7 10,9 11,9 12,9 13,3 13,7 14,6 15,4 16,1 16,8 17,5 18,2 18,8
6.025-470.0 23 34 45 57 68 79 85 91 102 113 125 136 147 159 170
1,00 8,5 10,4 12,0 13,4 14,7 15,9 16,4 17,0 18,0 19,0 19,9 20,8 21,6 22,4 23,2
6.025-198.0 28 42 56 70 84 98 105 112 126 140 154 168 182 196 210
1,10 10,3 12,6 14,5 16,2 17,8 19,2 19,9 20,5 21,8 23,0 24,1 25,1 26,2 27,2 28,1
9.885-951.0 34 51 68 85 102 119 127 136 152 169 186 203 220 237 254
1,20 12,2 15,0 17,3 19,3 21,2 22,9 23,8 24,4 25,9 27,3 28,6 29,9 31,1 32,3 33,5
6.025-199.0 40 60 81 101 121 141 151 161 181 202 222 242 262 282 302
1,25 13,3 16,2 18,7 21,0 23,0 24,8 25,7 26,5 28,1 29,6 31,1 32,5 33,8 35,1 36,3
6.025-471.0 44 66 88 109 131 153 164 175 197 219 241 263 284 306 328
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support.
The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 30
Round jet nozzle Form 4 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0 Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material -Nr. Material -No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
1,30 14,3 17,6 20,3 22,7 24,8 26,8 27,8 28,7 30,4 32,1 33,6 35,1 36,5 37,9 39,3
6.025-196.0 47 71 95 118 142 166 177 189 213 237 260 284 308 331 355
1,40 16,6 20,4 23,5 26,3 28,8 31,1 32,2 33,3 35,3 37,2 39,0 40,7 42,4 44,0 45,5
9.885-945.0 55 82 110 137 165 192 206 220 247 274 302 329 357 384 412
1,50 19,1 23,4 27,0 30,2 33,1 35,7 37,0 38,2 40,5 42,7 44,8 46,8 48,7 50,5 52,3
9.885-931.0 63 95 126 158 189 221 236 252 284 315 347 378 410 441 473
1,60 21,7 26,6 30,7 34,4 37,6 40,6 42,1 43,4 46,1 48,6 50,9 53,2 55,4 57,5 59,5
9.885-947.0 72 108 143 179 215 251 269 287 323 358 394 430 466 502 538
1,70 24,5 30,0 34,7 38,8 42,5 45,9 45,5 49,0 52,0 54,8 57,5 60,0 62,5 64,9 67,1
9.885-946.0 81 121 162 202 243 283 304 324 364 405 445 486 526 567 607
1,80 27,5 33,7 38,9 43,5 47,6 51,4 53,2 55,0 58,3 61,5 64,5 67,3 70,1 72,7 75,3
9.885-932.0 91 136 181 227 272 318 340 363 408 454 499 544 590 635 681
1,90 30,6 37,5 43,3 48,4 53,0 57,3 59,3 61,2 65,0 68,5 71,8 75,0 78,1 81,0 83,9
9.885-952.0 101 152 202 253 303 354 379 404 455 505 556 607 657 708 758
2,00 33,9 41,6 48,0 53,6 58,8 63,5 65,7 67,9 72,0 75,9 79,6 83,1 86,5 89,8 92,9
9.885-933.0 112 168 224 280 336 392 420 448 504 560 616 672 728 784 840
2,20 41,1 50,3 58,1 64,9 71,1 76,8 79,5 82,1 87,1 91,8 96,3 100,6 104,7 108,6 112,4
9.885-934.0 136 203 271 339 407 474 508 542 610 678 746 813 881 949 1017
2,30 44,9 55,0 63,5 71,0 77,7 83,9 86,9 89,7 95,2 100,3 105,2 109,9 114,4 118,7 122,9
9.885-964.0 148 222 296 370 444 519 556 593 667 741 815 889 963 1037 1111
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 31
Round jet nozzle Form 4 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0 Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material -Nr. Material -No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
2,40 48,9 59,8 69,1 77,3 84,6 91,4 94,6 97,7 103,6 109,3 114,6 119,7 124,6 129,3 133,8
9.885-935.0 161 242 323 403 484 565 605 645 726 807 887 968 1049 1129 1210
2,50 53,0 64,9 75,0 83,8 91,8 99,2 102,7 106,0 112,5 118,5 124,3 129,9 135,2 140,3 145,2
9.885-936.0 175 263 350 438 525 613 656 700 788 875 963 1050 1138 1225 1313
2,70 61,8 75,7 87,5 97,8 107,1 115,7 119,7 123,7 131,2 138,3 145,0 151,5 157,7 163,6 169,4
9.885-965.0 204 306 408 510 612 715 766 817 919 1021 1123 1225 1327 1429 1531
2,80 66,5 81,4 94,0 105,2 115,2 124,4 128,8 133,0 141,1 148,7 156,0 162,9 169,6 176,0 182,1
9.885-937.0 220 329 439 549 659 768 823 878 988 1098 1208 1317 1427 1537 1647
2,90 71,3 87,4 100,9 112,8 123,6 133,5 138,1 142,7 151,3 159,5 167,3 174,7 181,9 188,7 195,4
9.886-905.0 236 353 471 589 707 824 883 942 1060 1178 1295 1413 1531 1649 1766
3,00 76,3 93,5 108,0 120,7 132,2 142,8 147,8 152,7 161,9 170,7 179,0 187,0 194,6 202,0 209,1
9.885-938.0 252 378 504 630 756 882 945 1008 1134 1260 1386 1512 1638 1764 1890
3,20 86,9 106,4 122,8 137,3 150,4 162,5 168,2 173,7 184,3 194,2 203,7 212,8 221,5 229,8 237,9
9.885-939.0 287 430 574 717 860 1004 1075 1147 1290 1434 1577 1721 1864 2007 2151
3,30 92,4 113,1 130,6 146,1 160,0 172,8 178,9 184,8 196,0 206,6 216,6 226,3 235,5 244,4 253,0
9.886-904.0 305 457 610 762 915 1067 1144 1220 1372 1525 1677 1830 1982 2135 2287
3,50 103,9 127,3 147,0 164,3 180,0 194,4 201,2 207,8 220,4 232,4 243,7 254,5 264,9 274,9 284,6
9.885-940.0 343 515 686 858 1029 1201 1286 1372 1544 1715 1887 2058 2230 2401 2573
3,60 109,9 134,6 155,5 173,8 190,4 205,7 212,9 219,9 233,2 245,8 257,8 269,3 280,3 290,9 301,1
9.886-903.0 363 544 726 907 1089 1270 1361 1452 1633 1815 1996 2178 2359 2541 2722
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support.
The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 32
Round jet nozzle Form 4 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0 Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material -Nr. Material -No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
4,00 135,7 166,2 191,9 214,6 235,1 253,9 262,8 271,4 287,9 303,5 318,3 332,4 346,0 359,1 371,7
9.885-941.0 448 672 896 1120 1344 1568 1680 1792 2016 2240 2464 2689 2913 3137 3361
4,50 171,8 210,4 242,9 271,6 297,5 321,4 332,6 343,5 364,4 384,1 402,8 420,8 437,9 454,5 470,4
9.885-943.0 567 851 1134 1418 1701 1985 2127 2268 2552 2836 3119 3403 3686 3970 4253
5,00 212,1 259,7 299,9 335,3 367,3 396,7 410,7 424,1 449,9 474,2 497,3 519,4 540,7 561,1 580,8
9.885-942.0 700 1050 1400 1750 2100 2450 2625 2801 3151 3501 3851 4201 4551 4901 5251
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support.
The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 33
4.1.2 Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,60-10° 2,3 2,8 3,2 3,6 3,9 4,3 4,4 4,5 4,8 5,1 5,3 5,6 5,8 6,0 6,2
6.025-457.0 8 11 15 19 23 26 28 30 34 38 41 45 49 53 56
0,60-30° 2,3 2,8 3,2 3,6 3,9 4,3 4,4 4,5 4,8 5,1 5,3 5,6 5,8 6,0 6,2
6.025-458.0 8 11 15 19 23 26 28 30 34 38 41 45 49 53 56
0,70-10° 3,1 3,8 4,4 4,9 5,4 5,8 6,0 6,2 6,6 6,9 7,3 7,6 7,9 8,2 8,5
6.025-459.0 10 15 20 26 31 36 38 41 46 51 56 61 66 72 77
0,70-20° 3,1 3,8 4,4 4,9 5,4 5,8 6,0 6,2 6,6 6,9 7,3 7,6 7,9 8,2 8,5
6.025-460.0 10 15 20 26 31 36 38 41 46 51 56 61 66 72 77
0,70-30° 3,1 3,8 4,4 4,9 5,4 5,8 6,0 6,2 6,6 6,9 7,3 7,6 7,9 8,2 8,5
6.025-461.0 10 15 20 26 31 36 38 41 46 51 56 61 66 72 77
0,80-30° 4,0 4,9 5,7 6,4 7,0 7,6 7,8 8,1 8,6 9,0 9,5 9,9 10,3 10,7 11,1
9.886-186.0 13 20 27 33 40 47 50 53 60 67 73 80 87 93 100
0,90-10° 5,1 6,3 7,2 8,1 8,9 9,6 9,9 10,2 10,9 11,4 12,0 12,5 13,0 13,5 14,0
6.025-462.0 17 25 34 42 51 59 63 68 76 84 93 101 110 118 127
0,90-20° 5,1 6,3 7,2 8,1 8,9 9,6 9,9 10,2 10,9 11,4 12,0 12,5 13,0 13,5 14,0
6.025-463.0 17 25 34 42 51 59 63 68 76 84 93 101 110 118 127
0,90-30° 5,1 6,3 7,2 8,1 8,9 9,6 9,9 10,2 10,9 11,4 12,0 12,5 13,0 13,5 14,0
6.025-464.0 17 25 34 42 51 59 63 68 76 84 93 101 110 118 127
0,90-60° 5,1 6,3 7,2 8,1 8,9 9,6 9,9 10,2 10,9 11,4 12,0 12,5 13,0 13,5 14,0
9.912-874.0 17 25 34 42 51 59 63 68 76 84 93 101 110 118 127
1,00-10° 6,3 7,7 8,9 10,0 10,9 11,8 12,2 12,6 13,4 14,1 14,8 15,5 16,1 16,7 17,3
6.025-217.0 21 31 42 52 63 73 78 83 94 104 115 125 136 146 156
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 34
Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
1,00-20° 6,3 7,7 8,9 10,0 10,9 11,8 12,2 12,6 13,4 14,1 14,8 15,5 16,1 16,7 17,3
6.025-214.0 21 31 42 52 63 73 78 83 94 104 115 125 136 146 156
1,00-30° 6,3 7,7 8,9 10,0 10,9 11,8 12,2 12,6 13,4 14,1 14,8 15,5 16,1 16,7 17,3
6.025-215.0 21 31 42 52 63 73 78 83 94 104 115 125 136 146 156
1,00-40° 6,3 7,7 8,9 10,0 10,9 11,8 12,2 12,6 13,4 14,1 14,8 15,5 16,1 16,7 17,3
6.025-216.0 21 31 42 52 63 73 78 83 94 104 115 125 136 146 156
1,00-60° 6,3 7,7 8,9 10,0 10,9 11,8 12,2 12,6 13,4 14,1 14,8 15,5 16,1 16,7 17,3
9.886-163.0 21 31 42 52 63 73 78 83 94 104 115 125 136 146 156
1,10-10° 7,6 9,4 10,8 12,1 13,2 14,3 14,8 15,3 16,2 17,1 17,9 18,7 19,5 20,2 20,9
6.025-465.0 25 38 50 63 76 88 95 101 114 126 139 151 164 177 189
1,10-20° 7,6 9,4 10,8 12,1 13,2 14,3 14,8 15,3 16,2 17,1 17,9 18,7 19,5 20,2 20,9
6.025-466.0 25 38 50 63 76 88 95 101 114 126 139 151 164 177 189
1,10-30° 7,6 9,4 10,8 12,1 13,2 14,3 14,8 15,3 16,2 17,1 17,9 18,7 19,5 20,2 20,9
6.025-467.0 25 38 50 63 76 88 95 101 114 126 139 151 164 177 189
1,20-10° 9,1 11,1 12,9 14,4 15,8 17,0 17,6 18,2 19,3 20,3 21,3 22,3 23,2 24,1 24,9
6.025-206.0 30 45 60 75 90 105 113 120 135 150 165 180 195 210 225
1,20-20° 9,1 11,1 12,9 14,4 15,8 17,0 17,6 18,2 19,3 20,3 21,3 22,3 23,2 24,1 24,9
6.025-207.0 30 45 60 75 90 105 113 120 135 150 165 180 195 210 225
1,20-30° 9,1 11,1 12,9 14,4 15,8 17,0 17,6 18,2 19,3 20,3 21,3 22,3 23,2 24,1 24,9
6.025-208.0 30 45 60 75 90 105 113 120 135 150 165 180 195 210 225
1,20-45° 9,1 11,1 12,9 14,4 15,8 17,0 17,6 18,2 19,3 20,3 21,3 22,3 23,2 24,1 24,9
6.025-209.0 30 45 60 75 90 105 113 120 135 150 165 180 195 210 225
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 35
Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
1,20-60° 9,1 11,1 12,9 14,4 15,8 17,0 17,6 18,2 19,3 20,3 21,3 22,3 23,2 24,1 24,9
9.886-164.0 30 45 60 75 90 105 113 120 135 150 165 180 195 210 225
1,30-10° 10,7 13,1 15,1 16,9 18,5 20,0 20,7 21,3 22,6 23,9 25,0 26,1 27,2 28,2 29,2
6.025-468.0 35 53 70 88 106 123 132 141 159 176 194 211 229 247 264
1,30-30° 10,7 13,1 15,1 16,9 18,5 20,0 20,7 21,3 22,6 23,9 25,0 26,1 27,2 28,2 29,2
6.025-469.0 35 53 70 88 106 123 132 141 159 176 194 211 229 247 264
1,30-40° 10,7 13,1 15,1 16,9 18,5 20,0 20,7 21,3 22,6 23,9 25,0 26,1 27,2 28,2 29,2
9.886-184.0 35 53 70 88 106 123 132 141 159 176 194 211 229 247 264
1,40-10° 12,4 15,2 17,5 19,6 21,4 23,2 24,0 24,8 26,3 27,7 29,0 30,3 31,6 32,7 33,9
6.025-210.0 41 61 82 102 123 143 153 163 184 204 225 245 266 286 306
1,40-20° 12,4 15,2 17,5 19,6 21,4 23,2 24,0 24,8 26,3 27,7 29,0 30,3 31,6 32,7 33,9
6.025-211.0 41 61 82 102 123 143 153 163 184 204 225 245 266 286 306
1,40-30° 12,4 15,2 17,5 19,6 21,4 23,2 24,0 24,8 26,3 27,7 29,0 30,3 31,6 32,7 33,9
6.025-212.0 41 61 82 102 123 143 153 163 184 204 225 245 266 286 306
1,40-60° 12,4 15,2 17,5 19,6 21,4 23,2 24,0 24,8 26,3 27,7 29,0 30,3 31,6 32,7 33,9
6.025-213.0 41 61 82 102 123 143 153 163 184 204 225 245 266 286 306
1,50-10° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
6.025-201.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
1,50-15° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
6.025-202.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
1,50-20° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
6.025-203.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 36
Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
1,50-30° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
6.025-204.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
1,50-40° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
6.025-205.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
1,50-45° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
9.886-173.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
1,50-60° 14,2 17,4 20,1 22,5 24,6 26,6 27,5 28,4 30,1 31,8 33,3 34,8 36,2 37,6 38,9
9.886-169.0 47 70 94 117 141 164 176 188 211 235 258 281 305 328 352
1,60-10° 16,2 19,8 22,5 25,6 28,0 30,2 31,3 32,3 34,3 36,1 37,9 39,6 41,2 42,8 44,3
9.909-586.0 53 80 107 133 160 187 200 213 240 267 294 320 347 374 400
1,60-20°- 16,2 19,8 22,5 25,6 28,0 30,2 31,3 32,3 34,3 36,1 37,9 39,6 41,2 42,8 44,3
9.886-180.0 53 80 107 133 160 187 200 213 240 267 294 320 347 374 400
1,60-30° 16,2 19,8 22,5 25,6 28,0 30,2 31,3 32,3 34,3 36,1 37,9 39,6 41,2 42,8 44,3
9.886-181.0 53 80 107 133 160 187 200 213 240 267 294 320 347 374 400
1,70-10° 18,2 22,4 25,8 28,9 31,6 34,1 35,3 36,5 38,7 40,8 42,8 44,7 46,5 48,3 50,0
9.886-168.0 60 90 121 151 181 211 226 241 271 301 331 362 392 422 452
1,70-20° 18,2 22,4 25,8 28,9 31,6 34,1 35,3 36,5 38,7 40,8 42,8 44,7 46,5 48,3 50,0
9.886-153.0 60 90 121 151 181 211 226 241 271 301 331 362 392 422 452
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 37
Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
1,70-30° 18,2 22,4 25,8 28,9 31,6 34,1 35,3 36,5 38,7 40,8 42,8 44,7 46,5 48,3 50,0
9.886-152.0 60 90 121 151 181 211 226 241 271 301 331 362 392 422 452
1,70-60° 18,2 22,4 25,8 28,9 31,6 34,1 35,3 36,5 38,7 40,8 42,8 44,7 46,5 48,3 50,0
9.886-167.0 60 90 121 151 181 211 226 241 271 301 331 362 392 422 452
1,80-10° 20,5 25,1 28,9 32,4 35,4 38,3 39,6 40,9 43,4 45,7 48,0 50,1 52,2 54,1 56,0
9.886-161.0 68 101 135 169 203 236 253 270 304 338 372 405 439 473 507
1,80-20° 20,5 25,1 28,9 32,4 35,4 38,3 39,6 40,9 43,4 45,7 48,0 50,1 52,2 54,1 56,0
9.886-157.0 68 101 135 169 203 236 253 270 304 338 372 405 439 473 507
1,80-30° 20,5 25,1 28,9 32,4 35,4 38,3 39,6 40,9 43,4 45,7 48,0 50,1 52,2 54,1 56,0
9.886-154.0 68 101 135 169 203 236 253 270 304 338 372 405 439 473 507
1,80-40° 20,5 25,1 28,9 32,4 35,4 38,3 39,6 40,9 43,4 45,7 48,0 50,1 52,2 54,1 56,0
9.886-162.0 68 101 135 169 203 236 253 270 304 338 372 405 439 473 507
1,80-60° 20,5 25,1 28,9 32,4 35,4 38,3 39,6 40,9 43,4 45,7 48,0 50,1 52,2 54,1 56,0
9.886-172.0 68 101 135 169 203 236 253 270 304 338 372 405 439 473 507
1,90-30° 22,8 27,9 32,2 36,0 39,5 42,6 44,1 45,6 48,4 51,0 53,5 55,8 58,1 60,3 62,4
9.886-909.0 75 113 151 188 226 263 282 301 339 376 414 452 489 527 564
1,90-60° 22,8 27,9 32,2 36,0 39,5 42,6 44,1 45,6 48,4 51,0 53,5 55,8 58,1 60,3 62,4
9.886-166.0 75 113 151 188 226 263 282 301 339 376 414 452 489 527 564
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 38
Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
2,00-20° 25,3 30,9 35,7 39,9 43,8 47,3 48,9 50,5 53,6 56,5 59,2 61,9 64,4 66,8 69,2
9.886-145.0 83 125 167 208 250 292 313 334 375 417 459 500 542 584 625
2,00-30° 25,3 30,9 35,7 39,9 43,8 47,3 48,9 50,5 53,6 56,5 59,2 61,9 64,4 66,8 69,2
9.886-146.0 83 125 167 208 250 292 313 334 375 417 459 500 542 584 625
2,00-45° 25,3 30,9 35,7 39,9 43,8 47,3 48,9 50,5 53,6 56,5 59,2 61,9 64,4 66,8 69,2
9.886-158.0 83 125 167 208 250 292 313 334 375 417 459 500 542 584 625
2,00-60° 25,3 30,9 35,7 39,9 43,8 47,3 48,9 50,5 53,6 56,5 59,2 61,9 64,4 66,8 69,2
9.909-585.0 83 125 167 208 250 292 313 334 375 417 459 500 542 584 625
2,10-60° 27,8 34,1 39,4 44,0 48,2 52,1 53,9 55,7 59,1 62,3 65,3 68,2 71,0 73,7 76,3
9.886-165.0 92 138 184 230 276 322 345 368 414 460 506 552 598 644 690
2,20-10° 30,6 37,4 43,2 48,3 52,9 57,2 59,2 61,1 64,8 68,3 71,7 74,9 77,9 80,9 83,8
9.886-182.0 101 151 202 252 303 353 378 404 454 505 555 605 656 706 757
2,20-20° 30,6 37,4 43,2 48,3 52,9 57,2 59,2 61,1 64,8 68,3 71,7 74,9 77,9 80,9 83,8
9.886-147.0 101 151 202 252 303 353 378 404 454 505 555 605 656 706 757
2,20-30° 30,6 37,4 43,2 48,3 52,9 57,2 59,2 61,1 64,8 68,3 71,7 74,9 77,9 80,9 83,8
9.886-148.0 101 151 202 252 303 353 378 404 454 505 555 605 656 706 757
2,20-45° 30,6 37,4 43,2 48,3 52,9 57,2 59,2 61,1 64,8 68,3 71,7 74,9 77,9 80,9 83,8
9.909-584.0 101 151 202 252 303 353 378 404 454 505 555 605 656 706 757
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 39
Flat jet nozzle Form 19 Betriebsdruck: max. 1500 bar Operating pressure: max. 21750 psi
O-Ring 6.025-168.0
O-Ring muss gesondert bestellt werden. O-ring must be ordered separately.
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 9.885-944.0
Dummy Nozzle 9.885-944.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
2,20-45° 30,6 37,4 43,2 48,3 52,9 57,2 59,2 61,1 64,8 68,3 71,7 74,9 77,9 80,9 83,8
9.886-175.0 101 151 202 252 303 353 378 404 454 505 555 605 656 706 757
2,20-60° 30,6 37,4 43,2 48,3 52,9 57,2 59,2 61,1 64,8 68,3 71,7 74,9 77,9 80,9 83,8
9.886-912.0 101 151 202 252 303 353 378 404 454 505 555 605 656 706 757
2,40-25° 36,4 44,5 51,4 57,5 63,0 68,0 70,4 72,7 77,2 81,3 85,3 89,1 92,7 96,2 99,6
9.886-906.0 120 180 240 300 360 420 450 480 540 600 660 721 781 841 901
2,50-20° 39,5 48,3 55,8 62,4 68,4 73,8 76,4 78,9 83,7 88,3 92,6 96,7 100,6 104,4 108,1
9.886-155.0 130 195 261 326 391 456 489 521 586 652 717 782 847 912 977
2,50-30° 39,5 48,3 55,8 62,4 68,4 73,8 76,4 78,9 83,7 88,3 92,6 96,7 100,6 104,4 108,1
9.886-149.0 130 195 261 326 391 456 489 521 586 652 717 782 847 912 977
2,50-45° 39,5 48,3 55,8 62,4 68,4 73,8 76,4 78,9 83,7 88,3 92,6 96,7 100,6 104,4 108,1
9.886-160.0 130 195 261 326 391 456 489 521 586 652 717 782 847 912 977
2,70-60° 46,0 56,4 65,1 72,8 79,7 86,1 89,1 92,1 97,7 102,9 108,0 112,8 117,4 121,8 126,1
9.886-170.0 152 228 304 380 456 532 570 608 684 760 836 912 988 1064 1140
3,00-30° 56,8 69,6 80,4 89,9 98,4 106,3 110,1 113,7 120,6 127,1 133,3 139,2 144,9 150,4 155,6
9.886-150.0 188 281 375 469 563 657 704 751 844 938 1032 1126 1220 1313 1407
3,00-45° 56,8 69,6 80,4 89,9 98,4 106,3 110,1 113,7 120,6 127,1 133,3 139,2 144,9 150,4 155,6
9.886-151.0 188 281 375 469 563 657 704 751 844 938 1032 1126 1220 1313 1407
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein.
Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 40
4.2 Up to 3000 bar 4.2.1 Round jet nozzle Form 21 LL – Long Life with flow straightener
Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,15 0,2 0,2 0,3 0,3 0,3 0,4 0,4 0,4 0,4 0,4 0,5 0,5 0,5 0,5 0,5
9.886-918.0 1 1 1 2 2 2 2 3 3 3 4 4 4 5 5
0,20 0,3 0,4 0,5 0,5 0,6 0,6 0,7 0,7 0,7 0,8 0,8 0,8 0,9 0,9 0,9
6.025-445.0 1 2 2 3 3 4 4 5 5 6 6 7 7 8 9
0,25 0,5 0,7 0,8 0,9 0,9 1,0 1,0 1,1 1,1 1,2 1,3 1,3 1,4 1,4 1,5
6.025-238.0 2 3 4 4 5 6 7 7 8 9 10 11 12 13 13
0,30 0,8 1,0 1,1 1,2 1,4 1,5 1,5 1,6 1,7 1,7 1,8 1,9 2,0 2,1 2,1
6.025-248.0 3 4 5 6 8 9 10 10 12 13 14 15 17 18 19
0,35 1,1 1,3 1,5 1,7 1,8 2,0 2,1 2,1 2,3 2,4 2,5 2,6 2,7 2,8 2,9
6.025-239.0 4 5 7 9 11 12 13 14 16 18 19 21 23 25 26
0,40 1,4 1,7 2,0 2,2 2,4 2,6 2,7 2,8 2,9 3,1 3,3 3,4 3,5 3,7 3,8
6.025-240.0 5 7 9 11 14 16 17 18 21 23 25 27 30 32 34
0,45 1,8 2,2 2,5 2,8 3,0 3,3 3,4 3,5 3,7 3,9 4,1 4,3 4,5 4,6 4,8
6.025-241.0 6 9 12 14 17 20 22 23 26 29 32 35 38 41 43
0,50 2,2 2,7 3,1 3,4 3,8 4,1 4,2 4,3 4,6 4,8 5,1 5,3 5,5 5,7 5,9
6.025-242.0 7 11 14 18 21 25 27 29 32 36 39 43 47 50 54
0,55 2,6 3,2 3,7 4,1 4,5 4,9 5,1 5,2 5,6 5,9 6,2 6,4 6,7 6,9 7,2
6.025-243.0 9 13 17 22 26 30 32 35 39 43 48 52 56 61 65
0,60 3,1 3,8 4,4 4,9 5,4 5,8 6,0 6,2 6,6 7,0 7,3 7,6 8,0 8,3 8,5
6.025-244.0 10 15 21 26 31 36 39 41 46 52 57 62 67 72 77
0,65 3,7 4,5 5,2 5,8 6,3 6,9 7,1 7,3 7,8 8,2 8,6 9,0 9,3 9,7 10,0
6.025-245.0 12 18 24 30 36 42 45 48 54 60 67 73 79 85 91
0,70 4,2 5,2 6,0 6,7 7,4 7,9 8,2 8,5 9,0 9,5 10,0 10,4 10,8 11,2 11,6
6.025-236.0 14 21 28 35 42 49 53 56 63 70 77 84 91 98 105
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 41
Round jet nozzle Form 21 LL – Long Life with flow straightener
Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
Spritzwinkel Jet angle
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,75 4,9 6,0 6,9 7,7 8,4 9,1 9,4 9,8 10,3 10,9 11,4 11,9 12,4 12,9 13,4
6.025-441.0 16 24 32 40 48 56 60 64 72 81 89 97 105 113 121
0,80 5,5 6,8 7,8 8,8 9,6 10,4 10,7 11,1 11,8 12,4 13,0 13,6 14,1 14,7 15,2
6.025-442.0 18 27 37 46 55 64 69 73 82 92 101 110 119 128 137
0,85 6,3 7,7 8,9 9,9 10,9 11,7 12,1 12,5 13,3 14,0 14,7 15,3 16,0 16,6 17,2
6.025-443.0 21 31 41 52 62 72 78 83 93 103 114 124 134 145 155
0,90 7,0 8,6 9,9 11,1 12,2 13,1 13,6 14,0 14,9 15,7 16,5 17,2 17,9 18,6 19,2
6.025-444.0 23 35 46 58 70 81 87 93 104 116 128 139 151 162 174
0,95 7,8 9,6 11,1 12,4 13,6 14,6 15,2 15,7 16,6 17,5 18,4 19,2 20,0 20,7 21,4
9.886-913.0 26 39 52 65 78 90 97 103 116 129 142 155 168 181 194
1,00 8,7 10,6 12,3 13,7 15,0 16,2 16,8 17,3 18,4 19,4 20,3 21,2 22,1 22,9 23,7
9.886-914.0 29 43 57 72 86 100 107 115 129 143 157 172 186 200 215
1,05 9,6 11,7 13,5 15,1 16,6 17,9 18,5 19,1 20,3 21,4 22,4 23,4 24,4 25,3 26,2
9.886-915.0 32 47 63 79 95 110 118 126 142 158 174 189 205 221 237
1,10 10,5 12,9 14,8 16,6 18,2 19,6 20,3 21,0 22,3 23,5 24,6 25,7 26,7 27,8 28,7
9.886-916.0 35 52 69 87 104 121 130 139 156 173 191 208 225 242 260
1,15 11,5 14,0 16,2 18,1 19,9 21,5 22,2 22,9 24,3 25,6 26,9 28,1 29,2 30,3 31,4
9.910-959.0 38 57 76 95 114 133 142 151 170 189 208 227 246 265 284
1,20 12,5 15,3 17,7 19,7 21,6 23,4 24,2 25,0 26,5 27,9 29,3 30,6 31,8 33,0 34,2
9.886-917.0 41 62 82 103 124 144 155 165 186 206 227 247 268 289 309
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 42
Round jet nozzle Form 21 LL – Long Life
with flow straightener
Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 3000
Teile-Nr. Part-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,15 0,6 0,6 0,6 0,6 0,6 0,6 0,6 0,7 0,7 0,7 0,7 0,7 0,7 0,7 0,8
9.886-918.0 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10
0,20 1,0 1,0 1,0 1,1 1,1 1,1 1,2 1,2 1,2 1,2 1,3 1,3 1,3 1,3 1,3
6.025-445.0 9 10 10 11 11 12 13 13 14 14 15 15 16 17 17
0,25 1,5 1,6 1,6 1,7 1,7 1,8 1,8 1,8 1,9 1,9 2,0 2,0 2,0 2,1 2,1
6.025-238.0 14 15 16 17 18 19 20 21 21 22 23 25 25 26 27
0,30 2,2 2,3 2,3 2,4 2,5 2,5 2,6 2,6 2,7 2,8 2,8 2,9 2,9 3,0 3,0
6.025-248.0 21 22 23 24 26 27 28 30 31 32 33 35 36 37 39
0,35 3,0 3,1 3,2 3,3 3,4 3,4 3,5 3,6 3,7 3,8 3,8 3,9 4,0 4,0 4,1
6.025-239.0 28 30 32 33 35 37 39 40 42 44 46 47 49 51 53
0,40 3,9 4,0 4,2 4,3 4,4 4,5 4,6 4,7 4,8 4,9 5,0 5,1 5,2 5,3 5,4
6.025-240.0 37 39 41 44 46 48 50 53 55 57 60 62 64 66 69
0,45 5,0 5,1 5,3 5,4 5,6 5,7 5,8 6,0 6,1 6,2 6,3 6,5 6,6 6,7 6,8
6.025-241.0 46 49 52 55 58 61 64 67 70 72 75 78 81 84 87
0,50 6,1 6,3 6,5 6,7 6,9 7,0 7,2 7,4 7,5 7,7 7,8 8,0 8,1 8,3 8,4
6.025-242.0 57 61 64 68 72 75 79 82 86 89 93 97 100 104 107
0,55 7,4 7,6 7,9 8,1 8,3 8,5 8,7 8,9 9,1 9,3 9,5 9,6 9,8 10,0 10,2
6.025-243.0 69 74 78 82 87 91 95 100 104 108 113 117 121 126 130
0,60 8,8 9,1 9,4 9,6 9,9 10,1 10,4 10,6 10,8 11,0 11,3 11,5 11,7 11,9 12,1
6.025-244.0 82 88 93 98 103 108 113 119 124 129 134 139 144 149 155
0,65 10,4 10,7 11,0 11,3 11,6 11,9 12,2 12,4 12,7 13,0 13,2 13,5 13,7 14,0 14,2
6.025-245.0 97 103 109 115 121 127 133 139 145 151 157 163 169 175 181
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten. *
* In case of recoil force > 150 N the jetting device must be equipped with a body support.
The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 43
Round jet nozzle Form 21 LL – Long Life with flow straightener
Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 3000
Teile-Nr. Part-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,70 12,0 12,4 12,7 13,1 13,4 13,8 14,1 14,4 14,7 15,0 15,3 15,6 15,9 16,2 16,5
6.025-236.0 112 119 126 133 140 147 154 161 168 175 182 189 196 203 210
0,75 13,8 14,2 14,6 15,0 15,4 15,8 16,2 16,5 16,9 17,2 17,6 17,9 18,2 18,6 18,9
6.025-441.0 129 137 145 153 161 169 177 185 193 201 209 217 225 233 242
0,80 15,7 16,2 16,6 17,1 17,5 18,0 18,4 18,8 19,2 19,6 20,0 20,4 20,8 21,1 21,5
6.025-442.0 147 156 165 174 183 192 202 211 220 229 238 247 257 266 275
0,85 17,7 18,3 18,8 19,3 19,8 20,2 20,8 21,2 21,7 22,1 22,6 23,0 23,4 23,9 24,3
6.025-443.0 165 176 186 196 207 217 228 238 248 259 269 279 290 300 310
0,90 19,9 20,5 21,1 21,6 22,2 22,8 23,3 23,8 24,3 24,8 25,3 25,8 26,3 26,7 27,2
6.025-444.0 186 197 209 220 232 243 255 267 278 290 301 313 325 336 348
0,95 22,1 22,8 23,5 24,1 24,7 25,4 26,0 26,5 27,1 27,7 28,2 28,8 29,3 29,8 30,3
9.886-913.0 207 220 233 245 258 271 284 297 310 323 336 349 362 375 388
1,00 24,5 25,3 26,0 26,7 27,4 28,1 28,8 29,4 30,0 30,7 31,3 31,9 32,4 33,0 33,6
9.886-914.0 229 243 258 272 286 301 315 329 344 358 372 386 401 415 429
1,05 27,0 27,9 28,7 29,5 30,2 31,0 31,7 32,4 33,1 33,8 34,5 35,1 35,8 36,4 37,0
9.886-915.0 252 268 284 300 316 331 347 363 379 395 410 426 442 458 473
1,10 29,7 30,6 31,5 32,3 33,2 34,0 34,8 35,6 36,3 37,1 37,8 38,6 39,3 40,0 40,6
9.886-916.0 277 294 312 329 346 364 381 398 416 433 450 468 485 502 520
1,15 32,4 33,4 34,4 35,3 36,3 37,2 38,0 38,9 39,7 40,5 41,3 42,1 42,9 43,7 44,4
9.910-959.0 303 322 341 360 379 398 416 435 454 473 492 511 530 549 568
1,20 35,3 36,4 37,5 38,5 39,5 40,5 41,4 42,3 43,3 44,1 45,0 45,9 46,7 47,5 48,4
9.886-917.0 330 350 371 392 412 433 453 474 495 515 536 557 577 598 618
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 44
4.2.2 Round jet nozzle Form 21 S – Saphir with sapphire insert Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,12 0,1 0,1 0,1 0,1 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2 0,2
9.886-223.0 0 0 1 1 1 1 1 1 1 2 2 2 2 2 2
0,15 0,1 0,2 0,2 0,2 0,2 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,4 0,4 0,4
9.886-224.0 0 1 1 1 1 2 2 2 2 2 3 3 3 3 4
0,18 0,2 0,3 0,3 0,3 0,4 0,4 0,4 0,4 0,4 0,5 0,5 0,5 0,5 0,5 0,6
9.886-225.0 1 1 1 2 2 2 3 3 3 3 4 4 4 5 5
0,20 0,3 0,3 0,4 0,4 0,4 0,5 0,5 0,5 0,5 0,6 0,6 0,6 0,6 0,7 0,7
6.025-218.0 1 1 2 2 3 3 3 3 4 4 5 5 5 6 6
0,25 0,4 0,5 0,6 0,6 0,7 0,7 0,8 0,8 0,8 0,9 0,9 1,0 1,0 1,0 1,1
6.025-219.0 1 2 3 3 4 5 5 5 6 7 7 8 8 9 10
0,30 0,6 0,7 0,8 0,9 1,0 1,1 1,1 1,1 1,2 1,3 1,3 1,4 1,4 1,5 1,6
9.886-207.0 2 3 4 5 6 7 7 8 8 9 10 1 12 13 14
0,35 0,8 0,9 1,1 1,2 1,3 1,4 1,5 1,5 1,6 1,7 1,8 1,9 2,0 2,0 2,1
9.886-208.0 3 4 5 6 8 9 10 10 11 13 14 15 17 18 19
0,40 1,0 1,2 1,4 1,6 1,8 1,9 2,0 2,0 2,1 2,3 2,4 2,5 2,6 2,7 2,8
9.886-209.0 3 5 7 8 10 12 13 13 15 17 18 20 22 23 25
0,45 1,3 1,6 1,8 2,0 2,2 2,4 2,5 2,6 2,7 2,9 3,0 3,1 3,3 3,4 3,5
6.025-220.0 4 6 8 11 13 15 16 17 19 21 23 25 27 30 32
0,50 1,6 1,9 2,2 2,5 2,7 3,0 3,1 3,2 3,3 3,5 3,7 3,9 4,0 4,2 4,3
9.886-210.0 5 8 10 13 16 18 20 21 23 26 29 31 34 36 39
0,55 1,9 2,3 2,7 3,0 3,3 3,6 3,7 3,8 4,1 4,3 4,5 4,7 4,9 5,1 5,2
9.886-211.0 6 9 13 16 19 22 24 25 28 32 35 38 41 44 47
0,60 2,3 2,8 3,2 3,6 3,9 4,3 4,4 4,5 4,8 5,1 5,3 5,6 5,8 6,0 6,2
9.886-212.0 8 11 15 19 23 26 28 30 34 38 41 45 49 53 56
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 45
Round jet nozzle Form 21 S - Saphir
with sapphire insert Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
200 300 400 500 600 700 750 800 900 1000 1100 1200 1300 1400 1500
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,65 2,7 3,3 3,8 4,2 4,6 5,0 5,2 5,3 5,7 6,0 6,3 6,5 6,8 7,1 7,3
6.025-221.0 9 13 18 22 26 31 33 35 40 44 48 53 57 62 66
0,70 3,1 3,8 4,4 4,9 5,4 5,8 6,0 6,2 6,6 6,9 7,3 7,6 7,9 8,2 8,5
6.025-222.0 10 15 20 26 31 36 38 41 46 51 56 61 66 72 77
0,75 3,6 4,4 5,0 5,6 6,2 6,6 6,9 7,1 7,5 7,9 8,3 8.7 9,1 9,4 9,7
9.886-213.0 12 18 23 29 35 41 44 47 53 59 64 70 76 82 88
0,80 4,0 4,9 5,7 6,4 7,0 7,6 7,8 8,1 8,6 9,0 9,5 9,9 10,3 10,7 11,1
9.886-214.0 13 20 27 33 40 47 50 53 60 67 73 80 87 93 100
0,85 4,6 5,6 6,5 7,2 7,9 8,5 8,8 9,1 9,7 10,2 10,7 11,2 11,6 12,1 12,5
9.886-215.0 15 23 30 38 45 53 56 60 68 75 83 90 98 105 113
0,90 5,1 6,3 7,2 8,1 8,9 9,6 9,9 10,2 10,9 11,4 12,0 12,5 13,0 13,5 14,0
9.886-216.0 17 25 34 42 51 59 63 68 76 84 93 101 110 118 127
0,95 5,7 7,0 8,1 9,0 9,9 10,7 11,0 11,4 12,1 12,7 13,4 14,0 14,5 15,1 15,6
9.886-217.0 19 28 38 47 56 66 71 75 85 95 103 113 122 132 141
1,00 6,3 7,7 8,9 10,0 10,9 11,8 12,2 12,6 13,4 14,1 14,8 15,5 16,1 16,7 17,3
9.886-218.0 21 31 42 52 63 73 78 83 94 104 115 125 136 146 156
1,10 7,6 9,4 10,8 12,1 13,2 14,3 14,8 15,3 16,2 17,1 17,9 18,7 19,5 20,2 20,9
9.886-219.0 25 38 50 63 76 88 95 101 114 126 139 151 164 177 189
1,20 9,1 11,1 12,9 14,4 15,8 17,0 17,6 18,2 19,3 20,3 21,3 22,3 23,2 24,1 24,9
9.886-220.0 30 45 60 75 90 105 113 120 135 150 165 180 195 210 225
1,30 10,7 13,1 15,1 16,9 18,5 20,0 20,7 21,3 22,6 23,9 25,0 26,1 27,2 28,2 29,2
9.886-221.0 35 53 70 88 106 123 132 141 159 176 194 211 229 247 264
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support.
The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 46
Round jet nozzle Form 21 S - Saphir
with sapphire insert
Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 3000
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,12 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,4
9.886-223.0 2 3 3 3 3 3 3 3 4 4 4 4 4 4 5
0,15 0,4 0,4 0,4 0,4 0,4 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,6
9.886-224.0 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7
0,18 0,6 0,6 0,6 0,6 0,6 0,7 0,7 0,7 0,7 0,7 0,7 0,8 0,8 0,8 0,8
9.886-225.0 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10
0,20 0,7 0,7 0,8 0,8 0,8 0,8 0,8 0,9 0,9 0,9 0,9 0,9 0,9 1,0 1,0
6.025-218.0 7 7 8 8 8 9 9 10 10 10 11 11 12 12 13
0,25 1,1 1,2 1,2 1,2 1,2 1,3 1,3 1,3 1,4 1,4 1,4 1,5 1,5 1,5 1,5
6.025-219.0 10 11 12 12 13 14 14 15 16 16 17 18 18 19 20
0,30 1,6 1,7 1,7 1,8 1,8 1,8 1,9 1,9 2,0 2,0 2,0 2,1 2,1 2,2 2,2
9.886-207.0 15 16 17 18 19 20 21 22 23 23 24 25 26 27 28
0,35 2,2 2,3 2,3 2,4 2,4 2,5 2,6 2,6 2,7 2,7 2,8 2,8 2,9 2,9 3,0
9.886-208.0 20 23 23 24 26 27 28 29 31 32 33 34 36 37 38
0,40 2,9 2,9 3,0 3,1 3,2 3,3 3,4 3,4 3,5 3,6 3,6 3,7 3,8 3,8 3,9
9.886-209.0 27 28 30 32 33 35 37 38 40 42 43 45 47 48 50
0,45 3,6 3,7 3,8 3,9 4,0 4,1 4,2 4,3 4,4 4,5 4,6 4,7 4,8 4,9 5,0
6.025-220.0 34 37 38 40 42 44 46 49 51 53 55 57 59 61 63
0,50 4,5 4,6 4,7 4,9 5,0 5,1 5,2 5,4 5,5 5,6 5,7 5,8 5,9 6,0 6,1
9.886-210.0 42 44 47 50 52 55 57 60 63 65 68 70 73 76 78
0,55 5,4 5,6 5,7 5,9 6,0 6,2 6,3 6,5 6,6 6,8 6,9 7,0 7,1 7,3 7,4
9.886-211.0 50 54 57 60 63 66 69 73 76 79 82 85 88 91 95
0,60 6,4 6,6 6,8 7,0 7,2 7,4 7,5 7,7 7,9 8,0 8,2 8,4 8,5 8,7 8,8
9.886-212.0 60 64 68 71 75 79 83 86 90 94 98 101 105 109 113
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 47
Round jet nozzle Form 21 S - Saphir
with sapphire insert
Betriebsdruck: max. 3000 bar Operating pressure: max. 43500 psi
Gewinde/Thread: M10 Gewinde M nach ISO 261;Thread M as per ISO 261
Verwendung bei: Pistolen, Wasserwerkzeuge To use for: guns, water tools
Blinddüse 6.025-237.0 Dummy Nozzle 6.025-237.0
Düsen Nozzle
mm
Betriebsdruck / Operating pressure - bar -
1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600 2700 2800 2900 3000
Material-Nr. Material-No.
Düsendurchsatz / Flow rate - l/min Rückstoßkraft in Strahlrichtung / Recoil force in jetting direction /(N)*
0,65 7,5 7,8 8,0 8,2 8,4 8,6 8,8 9,0 9,2 9,4 9,6 9,8 10,0 10,2 10,3
6.025-221.0 70 75 79 84 88 92 97 101 106 110 115 119 123 128 132
0,70 8,8 9,0 9,3 9,5 9,8 10,0 10,3 10,5 10,7 10,9 11,2 11,4 11,6 11,8 12,0
6.025-222.0 82 87 92 97 102 107 112 117 123 128 133 138 143 148 153
0,75 10,0 10,4 10,7 10,9 11,2 11,5 11,8 12,0 12,3 12,6 12,8 13,1 13,3 13,5 13,8
9.886-213.0 94 100 106 111 117 123 129 135 141 147 152 158 164 170 176
0,80 11,4 11,8 12,1 12,5 12,8 13,1 13,4 13,7 14,0 14,3 14,6 14,8 15,1 15,4 15,7
9.886-214.0 107 113 120 127 133 140 147 153 160 167 173 180 187 193 200
0,85 12,9 13,3 13,7 14,1 14,4 14,8 15,1 15,5 15,8 16,1 16,5 16,8 17,1 17,4 17,7
9.886-215.0 121 128 136 143 151 158 166 173 181 188 196 203 211 218 226
0,90 14,5 14,9 15,3 15,8 16,2 16,6 17,0 17,3 17,7 18,1 18,4 18,8 19,1 19,5 19,8
9.886-216.0 135 144 152 160 169 177 186 194 203 211 220 228 236 245 253
0,95 16,1 16,6 17,1 17,6 18,0 18,5 18,9 19,3 19,7 20,1 20,5 20,9 21,3 21,7 22,1
9.886-217.0 151 160 169 179 188 198 207 216 226 235 245 245 263 273 282
1,00 17,9 18,4 18,9 19,5 20,0 20,5 20,9 21,4 21,9 22,3 22,8 23,2 23,6 24,0 24,5
9.886-218.0 167 177 188 198 208 219 229 240 250 261 271 281 292 302 313
1,10 21,6 22,3 22,9 23,6 24,2 24,8 25,3 25,9 26,5 27,0 27,5 28,1 28,6 29,1 29,6
9.886-219.0 202 214 227 240 252 265 277 290 303 315 328 341 353 366 378
1,20 25,7 26,5 27,3 28,0 28,8 29,5 30,2 30,8 31,5 32,1 32,8 33,4 34,0 34,6 35,2
9.886-220.0 240 255 270 285 300 315 330 345 360 375 390 405 420 435 450
1,30 30,2 31,1 32,0 32,9 33,7 34,6 35,4 36,2 37,0 37,7 38,5 39,2 39,9 40,6 41,3
9.886-221.0 282 299 317 335 352 370 388 405 423 440 458 476 493 511 529
* Bei Rückstoßkraft > 150 N muss die Spritzeinrichtung mit einer Körperstütze ausgerüstet sein. Die max. zulässige Rückstoßkraft für den manuellen Einsatz darf 250 N nicht überschreiten.
* In case of recoil force > 150 N the jetting device must be equipped with a body support. The max. permissible recoil force for manual operation must not exceed 250 N.
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 48
5 ELECTRIC ACCESSORIES
Fußschalter Foot switch
Material-Nr. Material-No.
Gewicht ca. Weight appr.
2-Kanal 2-channel
E-Exi - IP65 E-Exi - IP65
9.889-511.0 1,5 kg
2-Kanal 2-channel
24 V DC - IP65 24 V DC - IP65
9.889-501.0 1,5 kg
Kabeltrommel Cable drum
Material-Nr. Material-No.
Gewicht ca. Weight appr.
mit 30 m Kabel with 30 m cable
E-Exi E-Exi
9.890-413.0 5,8 kg
mit 50 m Kabel with 50 m cable
E-Exi E-Exi
9.890-411.0 9,5 kg
mit 30 m Kabel with 30 m cable
24 V DC 24 V DC
9.890-412.0 4,9 kg
mit 50 m Kabel with 50 m cable
24 V DC 24 V DC
9.890-410.0 7,1 kg
Drucktasterstation Remote control box
Material-Nr. Material-No.
Gewicht ca. Weight appr.
2-Kanal 2-channel
E-Exi E-Exi
9.890-387.0 0,5 kg
2-Kanal 2-channel
24 V DC 24 V DC
9.890-399.0 0,5 kg
E-Exi Box Umwandler / Converter
Material-Nr. Material-No.
Gewicht ca. Weight appr.
Gerätespannung Unit voltage
Wasserwerkzeug Water tool
von/from 12 V DC* in/into E-Exi 9.889-539.0* 5,5 kg
von/from 24 V DC in/into E-Exi 9.889-540.0 5,5 kg
*nur für Kompaktgeräte ET600/800, EC1000; EcoPro2500
*only to use for Compact Units ET600/800, EC1000, EcoPro2500
5 m Kabel/cable
3 m Kabel/cable
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 49
NOT - AUS Station Emergency Stop
mit Anschluss für Wasserwerkzeug
with connection for water tool
Material-Nr. Material-No.
Gewicht ca. Weight appr.
2-Kanal 2-channel
E-Exi E-Exi
9.890-388.0 0,5 kg
2-Kanal 2-channel
24 V DC 24 V DC
6.025-447.0 0,5 kg
NOT - AUS Station Emergency Stop
ohne Anschluss für Wasserwerkzeug
without connection for water tool
Material-Nr. Material-No
Gewicht ca. Weight appr.
2-Kanal 2-channel
E-Exi E-Exi
9.915-428.0 0,4 kg
2-Kanal 2-channel
24 V DC 24 V DC
9.889-528.0 0,4 kg
Stecker / Plug
Stecker / Plug
Dose / Socket
Dose / Socket
Copyright © 2015 WOMA GmbH | Subject to change | Stand: 04.2015 50
Contact and Support
WOMA GmbH Werthauser Str. 77 – 79 47226 Duisburg Postfach 14 18 20 47208 Duisburg Telefon +49 2065 304-0 Telefax +49 2065 304-200 E-Mail [email protected] Internet www.woma.de
Sales and Service Werthauser Str. 77 – 79 47226 Duisburg Telefon +49 2065 304-0 Telefax +49 2065 304-200 E-Mail [email protected]
Top Related