Motorola WR850G 6.1.4 Releasenotes

8/3/2019 Motorola WR850G 6.1.4 Releasenotes

1/14

Compatibility The features in this release are compatible with boththe WR850G and WR850GP Wireless BroadbandRouters.

Release 6.1.4 is compatible with all hardware versions

Changes in Release 6.1.4 (Relative to Releases 2.x, 3.x,4.x, and 5.x)

AP (access point) mode supports five Ethernet ports

HTML help this is now a pop-up tool

STP (spanning tree protocol) this is now user config-urable

Default SSID (service set identifier) the factorydefault setting for SSID includes the complete 12-digitMAC address

WMM (Wi-Fi Multimedia) supported

AP isolation supported

Multicast Rate settings supported

Parental Controls a subset of these settings are nowconfigured on the Filters configuration page

WPA2 (Wi-Fi Protected Access version 2) support-ed

Connection Logging via Syslog Service this hasreplaced URL (uniform resource locator) Log support

LED functions the Power LED does not blink when afirmware update is in progress. (See How to Upgradefor details.) The WAN (wide area network) LED no longerblinks red when it has lost its IP connection to its defaultgateway, or when the WAN connection repair procedureis still in progress. When the Wireless LED is off, the

wireless interface is not enabled by the firmware (nolonger displays red.) Also, when this LED is blinking, thewireless interface is enabled and active wireless trafficis present. The Wireless LED does not blink on WR850GV1 hardware. Refer to the WR850G/GP User Guide for acomplete description of LED functions.

User Interface (UI) User interface of Web-based con-figuration utility realigned to support direct access tomajor functions (WAN interface, LAN interface, wirelessinterface, and advanced routing features). Refer toTables 1 and 2 in this document to quickly locaterenamed and new features in the UI.

WR850G and WR850GPFirmware Release Notes

Version 6.1.4

PPTP (point-to-point tunneling protocol), NetworkDiagnostics and RIP (routing information protocol) theare not supported/configurable

Configuration file save and restore, Web Login Timeoand Wireless site monitor not supported

WEP key input pass phrase and ASCII input not sported

Known Limitations

When you upgrade to 6.x, the factory default configurationsettings are restored to your system. You will need to

customize your configuration settings using the Configuratiopages. Refer to How to Configure the WR850 after theupgrade procedure is completed.

Before You Upgrade

This is the work flow you should follow to prepare to upgrathe WR850G/GP:

A. Print out the current configuration settings

Before you upgrade, it is highly recommended that you printthe current configuration settings of your current firmwareversion so that configuration is easier to follow. To access aprint the Web-based configuration pages of versions 2.x, 3.x4.x or 5.x, follow the steps in To access the Web-basedconfiguration pages, then print out the pages and return tothis section.

B. Back up the old configuration file

Before you upgrade, back up your current versions config.bfile according to instructions supplied with that version.

C. Obtain the WR850G/GP User Guide for complete inmation about version 6.x

You may want to have the user guide handy as you upgradeunit. It contains complete information regarding each

configuration parameter. You can download the User Guidefrom:

http://broadband.motorola.com/consumers/support/default.a

D. Download the Conversion Utility

A conversion utility is supplied to make it easy for you to mthe old configuration file parameters to the new parameterlocations in version 6.x configuration screens. You candownload the conversion utility from the same link shown istep C. Be sure to save it to your hard drive.


2/14

. Run the Conversion Utility

un this utility to generate a text file that shows where theurrent configuration parameters are to be entered in theersion 6.x configuration screens.

1 Navigate and click the Converter.exe file youdownloaded in step D. The HomeNet Backup File Format

Converter main window appears:

2In the Input binary box, click Browse andlocate the config.bin file you saved in step B. Example:5x config.bin

3 In the Output file box, click Browse tolocate a folder to store this file, then type a name forthis file to be generated. Example: Version_6x.txt

4 In the Product ID box, type the product name.Example: WR850G

5 Click Run. When Done appears in the lower left

corner of the dialog box, click Exit.6 Check that the file is located in the folder you speci-fied in step 3, and then click the file to open it and printit.

OW TO UPGRADE

e sure to read Before You Upgrade prior to performinghis procedure. Never reset the unit while its upgrading.

o upgrade from version 2.x, 3.x, 4.x, or 5.x to version 6.x:

1 Download and save theMotorola_WR850_6.1.4.exe file from the MotorolaWeb site at the following link:

http://broadband.motorola.com/consumers/support/default.asp

2 Double-click the .exe file you just saved. Browse tothe default path C:\Motorola_Homenet (unless younamed it otherwise) and unzip the file.

3 Type http://192.168.10.1 in a Web browser.

4 When the Motorola Wireless Broadband Routerlogon dialog box appears, type your user name in the

User name box (if you changed it from the factory default(admin) the last timeyou upgraded).

5 Type your password in the Password box (if youchanged it from the factory default (motorola using alllowercase) the last timeyou upgraded).

6 Click LOG IN.

7 Click the Control Panel tab then the FirmwareUpdate tab to access the firmware information.

8 To locate the Firmware Update .trx file you down-loaded and unzipped in steps 1 and 2, type the path inthe Firmware Update File box, or clickBrowse to navigate to it. The default isC:\Motorola_Homenet.

9 When the .trx file appears in the Firmware UpdateFile box, click Update.

10 When the update is complete, click RESTART andfollow the prompts to restart the WR850

Clearing the Web Browser Cache

After you upgrade, you may need to clear the cache to viewthe upgraded Web page properly:

1 Open a Web browser, such as Microsoft InternetExplorer.

2 Select Tools\Internet Options.

3 In the Temporary Internet files box, click DeleteFiles.

4 In the Delete Files dialog box, select the Delete alloffline content check box and then click OK.

5 Click OK again.

Configuring the WR850G/GP

These release notes provide steps to reconfigure the basicsecurity and other settings so that you can get your systemrunning securely. These basic settings appear in white on theconfiguration pages of the user interface. This document alsoprovides a comprehensive mapping table of parameters sothat you can find the newly named corresponding parametersfrom previous versions. New parameters have also beenadded for Version 6.x.

How to Configure the WR850

After you complete the upgrade procedure, you can customconfigure the WR850 and its associated devices. Proceduresare provided for the commonly used options only. Refer tothe WR850 Wireless Broadband Routers (WR850GP andWR850G) User Guide for complete information.

Refer to Table 1 in this update to locate configurationparameters in previous versions (2x through 5.x) that havebeen renamed or moved to new configuration pages inversion 6.x. Refer to Table 2 in this update for new


3/14

arameters in version 6.x. Be sure to click Apply before youxit the current page, or the changes you entered will best.

o access the Web-based configuration pages:

1 Open a Web browser. In the URL field, typehttp://192.168.10.1 (the routers default IP address) andpress Enter.

2 At the Motorola Wireless Broadband Router loginwindow, type your user name in the User name box (ifyou changed it from the factory default (admin) the lasttimeyou upgraded).

3 Type your password in the Password box (if youchanged it from the factory default (motorola using alllowercase) the last timeyou upgraded). Then click OK.

he Basic configuration page appears.

o configure basic access control features of yourouter/access point:

1 Select the Basic tab on the configuration menu bar.

2 Type a new user name in the Configuration LoginUsernamebox. This allows you to access the configura-tion pages. (If you forget a user name, you can press theReset button on the unit to reset the default user nameto admin.)

!!If you use theRestore Factory Configurationbutton,ll of the configuration options will be reset to the originalactory default settings, not just the current page settings.

3 Type a new password in the ConfigurationLogin Password box. This allows you to accessthe configuration pages. (If you forget a password, youcan press the Reset button on the unit to reset thedefault user name to motorola.)

Note: TheRESET button on the back of the WR850resets a predetermined number of options to theirdefaults. Refer to Section 1 in the User Guide for details.

4 In the Time Zonebox, select a time zone from thelist. The default is Eastern Time.

5 When you finish making changes, click Apply.When it is done, click Continue. Review the changesand then go to another configuration page by selectinganother tab on the configuration menu bar.

Note: If you do not clickApplyand you move to anotheronfiguration page, the changes you just made will be lost.

o configure the router to support connections to

broadband services (wide area network):

Note: Refer to the text file you generated using theconversion utility to make changes on this page.

1 Select theWAN tab on the configuration menu bar.

2 In the Connection Mode box, select the pro-tocol indicated in the converted configuration text file:

DHCP an IP address is dynamically assigned to theWR850 (per the Dynamic Host Configuration Protocol(DHCP). This is typically used with cable modems orgateways, and DSL gateways.

Static an IP address is manually assigned to the WANconnection.

PPPoE Point-to-Point Protocol over Ethernet (PPPoE) isused. PPPoE is typically used with DSL modems.

Disabled the WAN connection is disabled.

DHCP is the default.

Note: Perform the steps below only if PPPoE was select-ed in step 2.

3 In the PPPoE Username box, type the username indicated in the converted configuration textfile.The default is blank.

4 In the PPPoE Password box, type the pass-word indicated in the converted configuration text file.

5 In the PPPoE Service Name box, type the servicename indicated in the converted configuration text file.

6 Be sure all other parameters listed in the .txt fileyou generated match the parameter fields on this screen.

7 Click Apply. When it is done, click Continue.Review the changes and then go to another configura-tion page by selecting another tab on the configurationmenu bar.

If you are done configuring, see Restarting the WR850.

To configure the Wireless network:

When you upgrade, any configuration settings for wirelessconnected devices are lost. Refer to the User Guide for more

information about each configuration parameter on theWireless page, and Table 1 to map previous versions ofwireless configuration parameters to the wirelessparameters in revision 6.x. Refer to Table 2 for new wirelessparameters.

Note: Refer to the text file you generated using theconversion utility in step E to make changes on this page.

1 Select theWireless tab on the configuration menubar.


4/14

2 In the Network Name (SSID) box, type theservice set identifier using up to 32 alphanumeric char-acters, as indicated in the converted configuration textfile.

When a client looks to connect wirelessly to the WR850, thisSID will be the identifier by which it recognizes theetwork.

he default is motorola plus the Wireless MAC Address,hich can be found on the product label.

In the Channel box, select the channel to use (in theU.S., available channels are 1 through 11). You canswitch the channel if you experience poor wireless per-formance due to interference.

4 Be sure all other parameters listed in the .txt fileyou generated match the parameter fields on this screen.

5 Click Apply. When it is done, click Continue.Review the changes and then go to another configura-tion page by selecting another tab on the configuration

menu bar. If you are done configuring, see Restartingthe WR850.

o configure the security options which protectnformation sharing over wireless connections:

When you upgrade, all security configuration settings areplaced with version 6.x defaults. Refer to Table 1 for moreformation about each configuration parameter on theecurity page.

Note: Refer to the text file you generated using the

onversion utility to make changes on this page.

1 Select the Security tab on the configuration menubar.

2 In the WPA-PSK box, select Enabled orDisabled from the list. This engages or disengages Wi-Fi Protected Access (WPA) authentication using thePre-Shared Key (PSK) method.

3 In the WPA2-PSK box, select Enabled or Disabledfrom the list. This engages or disengages Wi-FiProtected Access (WPA) version 2 authentication using

the Pre-Shared Key (PSK) method.Notes: 1) The next option (step 4) is dimmed unlessWPA, WPA2, WPA-PSK or WPA2-PSK is Enabled. 2) Foroptimum security, the same authentication and encryp-tion methods (step 4) should be used for the WR850 andall devices with which it will communicate. However,multiple methods can be used. For example, WPA-PSKand WPA2-PSK can be enabled concurrently to supportdevices with mixed capabilities. Refer toAuthentication Methods in Section 3 in the user guidefor details.

4 In the WPA Encryption box, select anencryption method:

TKIP engages the Temporal key Integrity Protocol

AES engages the Advanced Encryption Standard

TKIP + AES supports a mix of devices using thesetwo encryption methods

Notes: 1) The next option (step 5) is dimmed unlessWPA, WPA2, WPA-PSK or WPA2-PSK is Enabled. 2)Using at least 20 characters is strongly recommended forthe pass phrase. 3) As you enter the pass phrase, it doesnot appear. After you apply the changes, you can selectthe Show button to display the pass phrase in a smalldialog box.

5 In the WPA Pass Phrase box, type a phrase between 8and 63 alphanumeric characters or exactly 64 hexadeci-mal digits (0-9, A-F).

6 Click Apply. When it is done, click Continue. Reviewthe changes and then go to another configuration pageby selecting another tab on the configuration menu bar.

If you are done configuring, see Restarting the WR850.

How to Set Parental Controls

As indicated in the summary of changes in this document,parental controls can be set on the Filters configurationpage. See Section 3 of the updated WR850 WirelessBroadband Routers User Guide. Refer to Filters PageExamples Establishing Parental Controls on Internet Use

for reconfiguring parental controls with the 6.x WR850firmware.

Restarting the WR850

If you are done configuring and applying the changes, youare ready to restart the unit:

1 Print out each configuration page to retain a hardcopy of the new settings.

2 When you are finished printing, select the Basictab and click Restart.

3 After the WR850 reboots, click Continue. The Basicpage reappears.

Configuration Mapping

The following table provides a way for users to findconfiguration parameters renamed from earlier versions ofthe WR850 and locate them in version 6.x.


5/14

Table 1. Configuration mapping from versions 2.x, 3.x, 4.x, and 5.x to version 6.x

Pr ev i ou s p a r a met er n a me

(2.x, 3.x , 4,x , a n d 5.x)

Scr een / Pa ge l oca t i on

i n Pr ev i ou s Ver s i on s

Ver s i on 6.x p a r a met er

n a me

Scr een / Pa ge l oca t i on i n

Ver s i on 6.x a n d d ef a u l t

1 WAN Interface Internet > Basic Interface WAN

Interface

2 Connection

Mode

Internet > Basic Connection Mode WAN

DHCP

3 Connection

Repair

Internet > Basic Release and Renew buttons WAN

4 Connection

Status

Internet > Basic Connection Status WAN read-

only

5 IP Address Internet > Basic IP Address WAN

0.0.0.0

6 Subnet Mask Internet > Basic Subnet Mask WAN

0.0.0.0

7 Default

Gateway

Internet > Basic Default Gateway WAN

0.0.0.0

8 Obtain DNS

Server

Address

Automatically

Internet > Basic NA

9 Primary DNS Internet > Basic DNS Servers (1st) WAN blank

10 Secondary

DNS

Internet > Basic DNS Servers (2nd

field) WAN blank

11 Tertiary DNS Internet > Basic DNS Servers (3rd field) WAN blank

12 Host Name Internet > Basic Host Name WAN blank

13 Domain Name Internet > Basic Domain Name WAN blank

14 PPP

Authentication

Internet > Basic NA

15 PPP User

Name

Internet > Basic PPPoE Username WAN blank

16 PPP

Password/PPP

Internet > Basic PPPoE Password WAN blank

17 PasswordConfirm

Internet > Basic Same as PPoE Password WAN blank

18 PPP Service

Name

Internet > Basic PPPoE Service Name WAN blank

19 PPP Idle Time Internet > Basic PPPoE Max Idle Time WAN 60

20 PPP Auto

Reconnect

Internet > Basic PPPoE Keep Alive WAN

Disabled

21 PPP MTU Internet > Basic PPPoE MTU WAN 1492


6/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



22 PPTP Client

IP

Internet > Basic NA

23 PPTP ServerIP Internet > Basic NA

24 Factory WAN

MAC Address

Internet > Advanced MAC Address WAN blank

25 Cloned WAN

MAC Address

Internet > Advanced Same as MAC Address WAN

26 Learned MAC

Address

Internet > Advanced NA

27 Network

Name (SSID)

Wireless > Basic Network Name (SSID) Wireless (top)

motorola

plus the

WirelessMAC

Address

28 Channel

Number

Wireless > Basic Channel Wireless (top)

11

29 Operation

Mode

Wireless > Basic Wireless Mode Wireless

(top)

Compatibility

30 Performance

Enhancement

(WR850GP

only)

Wireless > Basic Performance Enhancement

(GP models only)

Wireless (top)

On =

WR850GP;

Off =WR850G

31 Wireless MAC

Address

Wireless > Basic Wireless Interface Wireless (top)

Wireless

MAC address

on product

label

32 SSID

Broadcast

(Enabled)

Wireless > Security Network Type Wireless (top)

Open

33 ESS

Authentication

Wireless > Security 802.11 Authentication

through WPA2-PSK (6

items)

Security

Open

34 Encryption

Status

Wireless > Security WPA Encryption or WEP

Encryption

Security

TKIP or

Disabled)

35 Field 802.1X

Mode

Wireless > Security 802.1X Authentication Security

Disabled

36 Key Input

Method

Wireless > Security NA


7/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



37 Pass Phrase Wireless > Security WPA Pass Phrase Security

blank

38 Key Length Wireless > Security NA39 Key Index Wireless > Security Current WEP Network Key

Index

Security 1

40 Key Content

(Keys 1

through 4)

Wireless > Security WEP Network Key 1, Key

2, Key 3, Key 4

Security

blank

41 Group Key

Renewal

Interval

Wireless > Security Network Key Rotation

Interval

Security 0

42 RADIUS

Server IP

Wireless > Security RADIUS Server Security

blank

43 RADIUS

Server Port

Number

Wireless > Security RADIUS Port Security

1812

44 RADIUS

Shared Secret

Wireless > Security RADIUS Shared Secret Security

blank

45 RADIUS

Shared Secret

Confirmation

Wireless > Security Same as RADIUS Shared

Secret

Security

46 Wireless MAC

Access Control

List

Wireless > Security Restricted Wireless MAC

Addresses

Wireless

(bottom)

47 Learned MAC

Addresses

Wireless > Security Authenticated Clients Wireless

(bottom)

blank

48 MAC Address Wireless > Site

Monitor

NA

49 Host Name Wireless > Site Mon. NA

50 Refresh Wireless > Site Mon NA

51 Scan Wireless > Site Mon NA

52 SSID Wireless > Site Mon NA

53 MAC Address Wireless > Site Mon NA

54 Channel Wireless > Site Mon NA

55 Signal

Strength

Wireless > Site Mon NA

56 Wireless Mode Wireless > Site Mon NA

57 Security Wireless > Site Mon NA

58 Radio Wireless > Advanced Wireless Enabled Wireless


8/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



Interface (bottom)

Yes

59 ShortPreamble Wireless > Advanced Preamble Type Wireless (top) Long

60 Frame

Bursting

Wireless > Advanced Frame Bursting Wireless

(top), Off =

WR850G; On

= WR850GP

61 RTS Threshold Wireless > Advanced RTS Threshold Wireless (top)

2347

62 Fragmentation

Threshold

Wireless > Advanced Fragmentation Threshold Wireless (top)

2346

63 Beacon Period Wireless > Advanced Beacon Interval Wireless (top)

100

64 DTIM Period Wireless > Advanced DTIM Interval Wireless (top)

3

65 Basic Rate Set Wireless > Advanced Basic Rate Set Wireless (top)

Default

66 11g Protection

Mode

Wireless > Advanced 802.11g Protection Mode Wireless (top)

Auto

67 WDS Mode

(Enable)

Wireless > Advanced NA

68 WDS Restrict

Mode (Enable)

Wireless > Advanced Wireless Bridge Restriction

Mode

Wireless

(bottom)

Enabled

69 WDS Restrict

MAC

Addresses

Wireless > Advanced Restricted Wireless MAC

Addresses

Wireless

(bottom)

70 Content Policy Parental Control >

Content Policy

NA

71 Policy Number Content Policy NA

72 Policy Name Content Policy NA

73 Allow URL Content Policy NA

74 Deny URL Content Policy NA

75 URL Content Policy NA

76 Keyword Filter Content Policy NA

77 Schedule Content Policy LAN Usage Filters table Filters

12:00AM to

12:00AM

78 MAC Filter Content Policy LAN MAC Filter Mode Filters


9/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



Deny

79 Learned MAC

Addresses

Content Policy NA

80 URL Log Parental Control >

URL Log

NA

81 URL Log

Table Refresh

URL Log NA

82 Visited URL URL Log NA

83 LAN IP URL Log NA

84 LAN MAC

Address

URL Log NA

85 LAN Host

Name

URL Log NA

86 Time URL Log NA

87 Service/Port

Number

URL Log NA

88 LAN MAC

Address

Networking > DHCP

Server

MAC Address LAN MAC

ID of LAN

port

89 LAN Private

IP

DHCP Server IP Address LAN

192.168.10.1

90 LAN Subnet

Mask

DHCP Server Subnet Mask LAN

255.255.255.0

91 LAN DHCP

Server

DHCP Server DHCP Server LAN -

Enabled

92 Address Pool

Begins

DHCP Server DHCP Starting IP Address LAN

192.168.10.2

93 Address Pool

Size

DHCP Server DHCP Ending IP Address LAN

192.168.10.254

94 Default Lease

Duration

DHCP Server DHCP Lease Time LAN 86400

95 Active Leases DHCP Server Active DHCP Leases LAN tableshows client

MAC IDs

96 LAN Private

Host Name

Networking >DNS

Proxy

NA

97 Host Table Networking >DNS

Proxy

NA

98 RIP V1 Networking > Routing NA

99 RIP V2 Networking > Routing NA


10/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



100 Routing Table

Entry List

Networking > Routing NA

101 DDNS Networking >Dynamic DNS DDNS Server WAN Disabled

102 DDNS Server Dynamic DNS DDNS Server WAN

Disabled

103 User Name Dynamic DNS DDNS User Name WAN blank

104 User Password Dynamic DNS DDNS User Password WAN blank

105 User Password

Confirm

Dynamic DNS Same as DDNS User

Password

WAN

106 Host Name Dynamic DNS DDNS Host Name WAN blank

107 NAT Networking > NAT NA

108 Gaming DMZ

Device

Networking > NAT DMZ IP Address Routing

blank

109 My Gaming

Device

Networking > NAT Same as DMZ IP Address Routing

blank

110 TCP Session

Idle Time

Networking > NAT NA

111 UDP Session

Idle Time

Networking > NAT NA

112 ICMP Session

Idle Time

Networking > NAT NA

113 Port Trigger

Name

Networking > Port

Trigger

NA

114 Outgoing

Protocol

Networking > Port

Trigger

Outbound Protocol (Port

Trigger table)

Routing

blank

115 Outgoing Port Networking > Port

Trigger

Outbound Port (Start/ End)

(Port Trigger table)

Routing

blank

116 Triggered

Incoming

Protocol

Networking > Port

Trigger

Inbound Protocol (Port

Trigger table)

Routing

blank

117Incoming Port Networking > PortTrigger Inbound Port (Start/ End)(Port Trigger table) Routing blank

118 Enable Networking > Port

Trigger

Enabled Routing

blank

119Virtual Server

Name

Network > Virtual

Server

NA

120 Incoming

Protocol

Network > Virtual

Server

Protocol (Port Forwards

table)

Routing

blank

121 Incoming Port Network > Virtual WAN Port (Start/End) (Port Routing


11/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



Server Forwards table) blank

122 Forwarding IP Network > Virtual

Server

LAN IP Address (Port

Forwards table)

Routing

blank`123 Forwarding

Port

Network > Virtual

Server

LAN Port (Start/End) (Port

Forwards table)

Routing

blank

124 Enable Network > Virtual

Server

Enabled (Port Forwards

table)

Routing

blank

125 Schedule Network > Virtual

Server

NA

126 Firewall Networking >Firewall Firewall Basic

Enabled

127 Multicast

Pass-through

Networking >Firewall NA

128 Login User ID Control Panel>Device

Security

Configuration Login

Username

Basic blank

129 Login

Password

Control Panel >

Device Security

Configuration Login

Password

Basic blank

130 Login

Password

Confirm

Control Panel >

Device Security

Same as Configuration

Login Password

Basic

131 WAN Web

Login

Control Panel >

Device Security

Remote Login Port Basic blank

132 WAN WebLogin Port

Control Panel >Device Security

Remote Login Port Basic

133 Login Idle

Time

Control Panel >

Device Security

NA

134 WAN Ping

Response

Control Panel >

Device Security

NA

135 Current Time Control Panel > Time Local Time Basic local

time

displayed

136 Time Zone Control Panel > Time Time Zone Basic

Eastern Time

137Auto Daylight

Adjust

Control Panel > Time Auto Adjust for Daylight

Saving Time

Basic

Enabled

138 NTP Time

Synchroniza-

tion

Control Panel > Time NA

139 NTP Server 1,

2, 3

Control Panel > Time Internet Time Server

Addresses

Basic blank


12/14


(2.x, 3.x , 4,x , a n d 5.x)




n a me



140 LAN UPnP

Device

Control Panel > UPnP Universal Plug and Play

(UPnP)

Basic

Disabled

141 Ping Internet > NetworkDiagnostic NA

142 Trace Route Internet > Network

Diagnostic

NA

143 DNS Lookup Internet > Network

Diagnostic

NA

144 Firmware

Revision

Control Panel >

Firmware Update

Firmware

Version

Firmware

read-only

Table 2. New configuration parameters in version 6.1.4

Scr een / Pa ge L oca t i on

i n Ver s i on 6.x

New p a r a met er n a me i n Ver s i on 6.x Def a u l t

Default Gateway 192.168.10.1LAN

Spanning Tree Protocol Enabled

Description Default

connection

WINS Servers blank

PPPoE AccessConcentrator blank

WAN

PPPoE MRU 1492

WAN IP Address

Expires In:

read-onlyWAN

Static Routes blank

System Up Time read-onlyStatus

Connection Log read-only

Filters page (in grid): blank

Protocol blank

Filters

Destination Port Range blank

Routing To Port Start /To Port

End (Port Triggers

table)

blank


13/14

Scr een / Pa ge L oca t i on

i n Ver s i on 6.x

New p a r a met er n a me i n Ver s i on 6.x Def a u l t

Wireless interface Wireless MAC

Address as printed

on product

AP Isolation Off

Rate Auto

Wireless

(top)

Maximum Associations 128

WMM Support Off

No Acknowledgement Off

EDCA AP Parameters: Off

Background AC

Best Effort AC

Video AC

Voice AC

EDCA Client

Parameters:

Off

Background AC

Best Effort AC

Video AC

Wireless

(middle)

Voice AC

Wireless

(bottom)

Bridge Link Detection

Interval

0

WPA2 Disabled

WPA2 Pre-

Authentication

Enabled

when WPA2

is Enabled

Security

WPA2-PSK Disabled


14/14

If You Need Help

If you need assistance while working with the WR850G/GP, contact the Motorola Technical Response Center(TRC):

Inside the U.S: 1-877-466-8646

Motorola Online:www.motorola.com/homenetworking(click Support and Downloads)

The TRC is on call 24 hours a day, 7 days a week. In addition, Motorola Online offers a searchablesolutions database, technical documentation, and low-priority issue creation and tracking.

MOTOROLA and the Stylized M Logo are registered in the US Patent &Trademark Office. WMM, Wi-Fi, and WPA2 are trademarks or registeredtrademarks of the Wi-Fi Alliance. All other product or service names are the

property of their respective owners. Motorola, Inc. 2005. All rights reserved.

No part of the contents of this manual may be reproduced or transmitted in anyform or by any means without the written permission of the publisher.

520949-001 08/05 MGBI
http://www.motorola.com/homenetworkinghttp://www.motorola.com/homenetworkinghttp://www.motorola.com/homenetworkinghttp://www.motorola.com/homenetworking

Motorola WR850G 6.1.4 Releasenotes

Documents

Transcript of Motorola WR850G 6.1.4 Releasenotes