Edition: March 2013
Bruker Manual
Micro/Macro Fiske teller
Manual for Micro/Macro Fiske teller
Page 1
Contents Forord – Micro/Macro Fiske teller ....................................................................................................................... 2
Montering ............................................................................................................................................................. 4
Telle Hode ............................................................................................................................................................. 5
Set Up ................................................................................................................................................................... 6
Pumping ............................................................................................................................................... 6
Vakum pumper .................................................................................................................................... 6
Håving .................................................................................................................................................. 6
Start ...................................................................................................................................................................... 7
Hoved skjerm ........................................................................................................................................................ 8
Valg av fiske størrelse ........................................................................................................................ 10
Test med vann ................................................................................................................................... 10
Start ny telling ................................................................................................................................... 11
Store and Continue Counting ............................................................................................................ 12
Video and Fish spread ....................................................................................................................... 12
Progress bar ....................................................................................................................................... 12
Clear one channel .............................................................................................................................. 13
End counting session ......................................................................................................................... 13
Settings ............................................................................................................................................................... 14
Settings .............................................................................................................................................. 14
Multi channel counting. .................................................................................................................... 14
Advanced ........................................................................................................................................... 15
Report ................................................................................................................................................ 16
Licence codes..................................................................................................................................... 16
Calibration & Visibility ........................................................................................................................................ 17
Visibility ............................................................................................................................................. 17
Counter calibration ............................................................................................................................ 19
View report ......................................................................................................................................................... 20
View record ........................................................................................................................................................ 21
Storing ................................................................................................................................................................ 22
Technical specification ....................................................................................................................................... 22
Standard Counters .............................................................................................................................................. 24
Manual for Micro/Macro Fiske teller
Page 2
Forord – Micro/Macro Fiske teller
VAKI gratulerer deg med valget av MICRO og MACRO fisketeller.
VAKI MICRO og MACRO er utviklet i samarbeid med en rekke ledende oppdrettsselskap for telling av Laks,
Ørret, Sea bass, Bream, Torsk og flatfisk. Vaki har jobbet kontinuerlig med tilpassing av funksjoner og for
tilpassing av telling av arter som reke og rensefisk.
Begge tellerene baserer seg på linjescanning som tellemetode. Fisk som passerer tellefeltet blir registrert og
lagret via kamera, spesialdesignet programvare analyserer bildene og registrerer hver enkelt fisk. Etter hver
telling vil man ha anledning til å generere en rapport som understøttes av et verifiseringsopptak fra tellingen
MICRO er ideell ved telling av fisk fra 0.2 g og har et 500mm bredt tellefelt, MACRO telleren er 1000mm bred
og er ideell ved telling av yngel og smolt.
Denne manualen er en guide for bruk av MICRO og MACRO teller.
Manual for Micro/Macro Fiske teller
Page 3
Garanti
VAKI Aquaculture Systems Ltd. tilbyr 1 års garanti fra leveringsdato hos VAKI Island, med forbehold om riktig
montering, bruk, vedlikehold i henhold til beskrivelse.
Endringer i starttidspunktet av garantien pga forsinket levering til kunde, må rapporteres skriftlig til VAKI.
VAKI forplikter seg til å utbedre alle mangler som skyldes feil på design, materialer eller produksjonen av
utstyret
Disse feilene vil bli rettet ved reparasjon eller utskiftning av komponenter. Kunden kan bli bedt om å sende
inn komplett utstyr eller enkeltdeler for reparasjon hos VAKI på Island
VAKI aksepterer tilsvarende garanti for originale deler som monteres av VAKI. Garantitiden er 1 år fra
levering VAKI Island.
VAKI er ikke ansvarlig for:
Feil montering og bruk eller utilstrekkelig vedlikehold.
Defekter som følge av montering av materialer, komponenter eller enheter som
ikke er levert av VAKI, og montert av brukeren
Mangler som skyldes endringer i utstyret av brukeren, uten skriftlig samtykke
fra VAKI.
Feil eller utilstrekkelige reparasjoner utført av brukeren.
Normal slitasje av utstyret.
Feil tilkobling av elektrisk utstyr
Feil forårsaket av uriktig spenning
Skade/stans på grunn av at Pc og/ eller kamera utsettes for vann/fukt.
Skade på elektriske kabler.
Økonomiske tap som følge av produksjonsstopp eller feiltelling.
Dersom feil eller mangler vises/oppdages på utstyret skal dette rapporteres omgående skriftlig til VAKI.
Rapporten må være sent innen 2 uker før garantitiden utløper.
Dersom kjøperen ikke informerer VAKI innenfor de frister som er angitt ovenfor vil retten til garanti bortfalle.
Manual for Micro/Macro Fiske teller
Page 4
Montering Ved levering må hovedkomponentene,
tellehode,tellebody,ben,innløp og utløp skrus
sammen. (se video på www.vaki.is) Bena er
montert og utstyrt med hjul foran. Innløp og utløp
boltes til bodyet som vist.
For å sikre at kameraet blir riktig innstilt er det
viktig å sette tellehodet nøyaktig på plass.
Micro / Macro kan settes opp som en 1- kanals
eller flerkanals teller. Hovedtrinnene i
monteringen er lik.
Utstyr som leveres: 2 x USB kabel 1 x Standard LAN kabel 1 x Strøm kabel 1xTelle Manual 1 x Flaske VAKI Fluid 1 x Ekstern Alarm 1 x Computer Manual Valgfritt tillegsutstyr: Størrelsesmåling, UPS 80 – 100W (un-interrupted power supply), USB tastatur, Mouse& Printer, 2 –way Batch splitter, CD reader/writer, Twisted LAN cable. Internal heating kit. 2 x USB cables 1 x Standard LAN cable 1 x Power cable 1 x Counter Manual 1 x External Alarm 1 x Computer Manual
Fler-kanals
innløp
1 kanals innløp
Vannavsiling
Ben
De-watering
outlet
Legs
Telle Hode Teller body Lampe huset Utløp
Manual for Micro/Macro Fiske teller
Page 5
Telle Hode Tellehodet inneholder kamera, Pc og touch panel.
Ved/under skjermen finnes tilkoblingsporter og innganger for tilkobling av strøm, lampe, alarm og evt
ekstrautstyr som tastatur, batch splitter.
1. Strøm tilkobling. 2. Av / på knapp 3. Local Area Network (LAN) tilkobling. 4. USB port, for tastatur, printer, mus. 5. USB port. 6. Serial Communication Port. 7. Alam tilkobling for overbelastning / batch
splitting. 8. Lampe tilkobling.
1 2 3 5 6 4
1
4
8 7
Store
Manual for Micro/Macro Fiske teller
Page 6
Set Up Under montering/ oppsett av Micro eller Macro er det viktig å merke seg følgende:
Telleren må plasseres på flatt og stabilt underlag.
Bruk nivå indikator for innjustering av telleren for å sikre at både vann og fisk oppnår god spredning over tellefeltet.
Plasser telleren slik at touch panelet har enkel tilkomst og ikke blir eksponert for vann eller direkte sollys. Merk at høye temperaturer kan ha innvirkning på telleren.
Før hver telling kontrolleres det at speilet er rent, fritt for rester og flekker av vanndråper.
Sikre at alle slanger og tilkoblinger er tilstrekkelig festet.
Koble til kabelen for lampen til tellehodet.
Koble til ekstern alarm i “Ctrl” port
Koble til stømkabel Bruk av UPS (un-interrupted power supply) er anbefalt. Tellerens strømbehov er 80-100W.
Sikre at vann og fisk har fri flow både gjennom og ut av telleren. Tilbakeslag i slangene kan overbelaste telleren.
Telleren skal ikke beveges eller flyttes når den er tilkoblet. Dette for å hindre harddisk feil.
Pumping Ved bruk av pumpe til transport av fisk til telleren er det viktig å oppnå en jevn flow av fisk og vann. Ujevn
pumping av fisk gjennom telleren kan redusere nøyaktigheten samt kapasiteten.
Det er viktig å prøvekjøre telleren med den vannmengden man vil benytte under selve tellingen opp i mot ny
innstilling for fiskestørrelse. Dette for å unngå eventuell overtelling.
Ref: section 7.2 “Test with water only”
Vakum pumper Ved bruk at store vakumpumper under telling kan det være behov for ytterligere vannavskilling eller at fisk
går via en buffertank.”Topper” med vann og spesielt skumfyllt vann eller fisk kan påvirke nøyaktigheten av
tellingen. Dette kan ha stor innvirkning, spesielt på mindre
Håving Ved håving av fisk under telling er det nødvendig å tilsette en jevn fin strøm med transportvann gjennom
telleren.
Manual for Micro/Macro Fiske teller
Page 7
Start
Telleren er nå montert og satt opp som instruert.
Skru på Pc Vent ca 10 minutter slik at software og lampe startes opp.
Følgende vindu vil vises på skjermen.
Dersom telleren nylig har vært i bruk og lampen ikke har blitt
kald kan man hoppe over oppvarmingsprosessen ved å trykke
på “cancel”
Dersom telleren brukes ved lave temperaturer er det
viktig at teller skues på i god tid før operasjonen.
Hovedskjermen vil så vise:
Manual for Micro/Macro Fiske teller
Page 8
Hoved skjerm Funksjoner og muligheter på hovedskjermen.
1. “Ny telling” starter en ny telling, etter aktivering endres knappen til “Stopp telling” 2. “Lagre” for å gjøre en mellomlagring vist i tellerapporten
OBS: husk å lagre siste batchen før tellingen avsluttes
3. “Innstillinger” meny for innstillinger. 4. “Visibility” brukes for å synliggjøre visibilitykurven (intensitet på lyset som kameraet registrerer) 5. “Kalibrering” for en automatisk kalibrering av telleren. 6. “Opptak” for å vise opptak av tellingen. 7. “Rapport” for å vise rapporter fra tellingen. 8. “lukk” for å kru av software før Pc skrus av.
Store
1 2°
1
2
3 4 5 6 7 8
Manual for Micro/Macro Fiske teller
Page 9
A. “Telling” / eller “Ikke telling” indikerer om telleren er klar for telling. Dersom dette området er rødt og viser “Not counting” og feilmelding “visibility insufficient” vises,
se kapittel for kalibrering & Visibility.
B. Total sum av alle kanaler. C. Kanaler. Navnene kan endres i innstillinger. D. Knapper for justering av fiskestørrelse som skal telles i de ulike kanalene. E. Størrelses gruppe valgt størrelse med justeringsknapp.(husk å stille alle kanaler) F. Gjennomstrømnings kurve, den blå grafen indikerer mengden fisk gjennom telleren og den rode
grafen viser maksimum antallet som telleren vil akseptere. G. Belastnings indikator som viser hvor hardt telleren belastes. Dersom baren endres til rød befinner
man seg i overkapasitet. H. Antall i kanalen.
3,9 g
C
1
F
G
1
Store
H
1
D
1 A
1
E
F
1
G
1
B
1
Manual for Micro/Macro Fiske teller
Page 10
Valg av fiske størrelse Størrelses valgene er: 0.2g, 1g, 3g, 10g, 30g, 100g & 200g
Bruk innstillingene og velg den størrelsesgruppen some er nærmest fiskegruppen som skal telles (Husk å
sette inn størrelse på hver kanal). Hver størrelses innstilling kan håndtere fisk som er 5 x mindre og 5 x større
enn valgte innstilling
Dersom innstillinger til liten fisk viser seg å overtelle pga luftbobler og/ eller bevegelser i vannet anbefales
det å øke størrelsesinnstillingen.
Test med vann Juster mengden fra fiskepumpen i forhold til fiskestørrelsen som skal telles. Ved telling av liten fisk reduseres
vannmengden så mye som mulig for å unngå feiltelling. Benytt vannavskiller for å justere vannmengden
gjennom telleren.
Plastikk flapsen brukes for å jevne ut vannstrøm og
fiskemengde gjennom telleren.
Justeringsskrue til ventil for justering av vannavskiller.
Testkjør telleren med vann (uten fisk) for å kontrollere at telleren ikke “teller vann”
Det kan være nødvendig å justere vannmengden for å unngå dette , spesiellt ved telling av liten fisk. Dersom
telleren “teller vann” kan følgende punkter gjennomgås:
Speilet er ikke rent eller har vanndråper For høy vannstrøm gjennom telleren Urent vann / farget vann. Telleren står ikke i water/ vannet er ikke spredt ut i hele tellefeltet Størrelses innstillingen er for sensitiv
Manual for Micro/Macro Fiske teller
Page 11
Start ny telling Start telling ved å trykke “Ny telling” knappen.
Displayet vil vise:
Informasjon om anleggsnavn, kar, gruppe etc kan føres inn ved å trykke på tastaturet. Denne informasjonen
inkluderes i rapporten. Trykk enter på tastaturet etter inntasting. DET ER VIKTIG AT DET KUN BENYTTES
BOKSTAVER OG TALL NÅR INFORMASJON TASTES INN. (.,-/_&) VIL GJØRE AT DATAFILEN IKKE BLIR LAGRET.
The counter should now show 0 in all counting windows. Start pumping or netting the fish into the counter.
Manual for Micro/Macro Fiske teller
Page 12
Store and Continue Counting An intermediate count can be stored by pressing the “Store” button. Then the following message will be
shown.
The number will be stored to the report together with the time label.
Video and Fish spread The Video tab shows the real time camera image of the scanning area. This screen can be used to view how
the fish pass thru the counter and identify any obstructions or obects remaing in the camera´s fied of view.
The Fish spread function shows a graphical representation of the position and quantity fish passing thru the
counter across the scaning area. An even spread of fish across the scanning area will give maximum capacity
and accuracy.
Progress bar The progress bar gives an indication of the rate of fish going thru the counter and relation to counter
capacity limit. The progress bar will change from green to amber as the the flow rate of fish increases
toward maximum counter capacity and finally go red when the flow rate is on or over the maximum limit of
the counter.
Manual for Micro/Macro Fiske teller
Page 13
Clear one channel It is possible to reset the number each counting channel, this will set the channel count back to „0“ but will
not affect the total count.
End counting session When counting is finished press “End counting session”.
The counting report containing information on the counting session including total and individual channel
counts, stored numbers, and the image record are stored.
It is now possible to view the recording and print reports and start a new counting session.
Manual for Micro/Macro Fiske teller
Page 14
Settings To access the settings function press “Settings” on the main screen.
Settings In the screen below it is possible to choose between languages. Select the species for the biomass function
and the weight constants can also be used to fine tune the average weight calculations for each group.
The Control function is for devices connected to the “Alarm” connector on the counting head. There are 4 options:
1. None: No control function activated 2. Overload Alarm: enables an external alarm to
sound when the counter is overloaded. 3. Batch Alarm: sets the external alarm to signal
when the batch number is reached.
Batch Number: This is used to set the number at which the batch alarm or batch splitter will be activated. “Reset” this button is used to turn off the external alarm and to switch between outlets on the batch splitter.
Folder for Report and Record file: This shows where the folder is located that stores the report and image files created after a counting session. The preset folder is c:\reports\.
Multi channel counting. Both Micro and Macro counters are avaialbe in multi channel configerations which can be used for counting
from graders. The Multi channel versions of the counters may also be used in a single channel mode.
To convert a multi channel counter to single channel version remove the channel dividers from the counter
inlet. Fish can then be pumped directly into the counter via the upwelling inlet undeneath the counter or
The program version: 386 The software serial number is 37828 The camera serial number is 13036428
Manual for Micro/Macro Fiske teller
Page 15
netted directly into the inlet. The multi channel outlet can be also be removed and replaced with the single
outlet.
The counting program is changed between multi and single channel modes by checking the Multi channel
counting box as shown in the Settings screen below. The Channel Labels box are used to rename the
counting channels (Counter 1, Channel 1, Small, Large, etc).
It is recommended to leave the program in multi channel counting mode even when using the counter as a
single channel counter. This allows the monitoring of the numbers of fish passing through each channel
section within the counter to ensure that fish are spread evenly across the counter, maximising capacity.
Advanced
“Line Scan Rate” Shows how many lines per second the camera is scanning.
Manual for Micro/Macro Fiske teller
Page 16
“Light Strength” This value indicates the strength of the lamp. Normally this value should be 1000-1400. Should the value drop below 700 this suggests the lamp tube should be replaced.
“Image buffer size” For Vaki engineer debugging purposes only
“Voltage” should be 11V or 12V
“Temperature” This shows the temperature of the camera, optimal around 38◦C.
“Active Biomass function” Indicates the status of the biomass function.
“Imaging hardware” For analog camera select Itex. For digital camera select GigE.
“Counter type” Shows the counter type the software is open for.
Report Here it is possible to enter the name of the operator and the company and an image file with the company
logo to included in the Count Reports.
Licence codes This field shows current liscence codes running on the counter.
Manual for Micro/Macro Fiske teller
Page 17
Calibration & Visibility Each time the counter starts it carries out the following checks:
The scanning area of the camera. That the coutner detecy all internal bulkheads
The intensity of the light detected by the camera.
If the visibility is not acceptable, the following message will appear “Insufficient visibility check again?” To
find what is wrong, push the “Visibility” button.
Visibility Press “Visibility” button to show the visibility graph:
The black vertical lines indicate the edges of the area scanned by the camera, which should correspond to
the inside edges of the counting channel.
The “Visibility” function is also used to
check that the camera is correctly
positioned and the amplification of the
light is correct. It is also possible to check
if dirt or residue blocks or disturbs the
sight of the camera.
This diagram on the left shows how the
graph should look in a single channel
Macro. It shows the position of the edges
of the scanning area with two vertical
black lines. It also shows that the light
intensity detected by the camera is even.
The scanning area on this graph is the distance between 500 and 1500 on the x-axis, and on the y-axis, the
strength of the light is approx. 220. The x-axis is the length of the scanning area in pixels (1 pixel = appx.0.55
mm). The graph for Micro should indicate 900 pixels (500mm) and the Macro 1,800 pixels (1,000mm). The y-
axis is the strength of the light on scale 0 to 255. The counter ignores the area outside the edges. If the
strength is under 180 or over 250, the counter must be re-calibrated. (See section: 10.2 Counter Calibration)
The diagram on the right shows how the graph can look
when something disturbs the light. In this case, the reason
may be humidity or dirt on the mirror. This would prevent
calibration of the camera. In this case, it is necessary to
clean the mirror.
Manual for Micro/Macro Fiske teller
Page 18
The black vertical lines should be positioned where the light intensity (shown by the red curve) falls
steeply. If not it is necessary to re calibrate (see Counter Calibration).
Visibility graph
Below is the curve for a four channel Macro.
It is possible to zoom in.
If no red curve appears this may be caused by, no light source (lamp) or the counting head is not positioned correctly on the counter body.
Manual for Micro/Macro Fiske teller
Page 19
Counter calibration
The Calibration function calculates a new position
automatically. Press “Calibration” button on main
screen with no water running through the counter.
It is also important that the lamp has been on for
five minutes or more and the mirror and camera
window are clean. Wait until counting message
appears on bottom left of screen. It is good practice
to re check the “Visibility” graph. If the edges of the
scanning area are still not acceptable then it may
need to be done manually.
Manual for Micro/Macro Fiske teller
Page 20
View report After pressing “End counting session”, the
programme automatically creates a report file. To
open and view the reports press the “Report”
button on main screen. A list of all stored
counting reports is displayed. Each report is
labelled by date and tank name. With the Biomass
function the average weight, total biomass,
standard deviation, and size distribution chart is
included in the report.
A company logo can be printed on the top right of
the report. The logo must be in a Windows
Bitmap format and under the filename logo.bmp
in the folder c:\Reports
Manual for Micro/Macro Fiske teller
Page 21
View record
To view the images stored press “Record” on the main screen. The files are labelled by date and tank name,
open the file to be viewed from the list. Each screen shows a recording for around one-second interval.
The graph at the top of the screen indicates the rate of fish through the counter over time. Press the graph
and a graph for the next counting channel will be shown.
◄, ► buttons are used to move to the next screen
◄ , ► buttons locate the beginning and end of the recording.
Start/End button, is used to select a part of the recording to be counted.
The pointer indicates the location of the screen currently viewed and can be dragged to quickly locate a
position in the recording.
“Close” to exit.
Manual for Micro/Macro Fiske teller
Page 22
Storing When storing the Bioscanner Micro or Macro it is important to bear the following in mind:
Store the Counting Head in a safe, dry place where there are minumum temperature fluctuations.
Clean any salty seawater off the counter with fresh water after use.
Ensure the counting head is handled with care.
Technical specification
Macro Size:
2.5 x 1.2 x 1.6-2.4 m (L x W x H)
Micro Size:
1.5 x 0.7 x 1.6-2.4 m (L x W x H)
Material: Stainless steel (AISI 316L)
Light source: Micro Counter Macro Counter
18W 60cm 18/12-950 36W 120cm 18/12-950
Osram colour ref 950
Power consumption: 110/220 V
UPS requirement: 80-100W
Size of inlet/outlet pipes: 4”on Micro / 6” on Macro
Size of dewatering pipe: 4” on Micro / 6”on Macro
Manual for Micro/Macro Fiske teller
Page 23
Capacity:
Fish size Micro Counter Macro Counter
Fry/min
0,5 g 9500 14000
1 g 6500 10200
3 g 4300 7200
10 g 2800 4800
30 g 1600 3080
100g 800 1600
200g 600 1200
Accuracy: 98% -100%
Fish sizes: Macro 0.2g – 400g
Micro 0.2g – 200g
Fish species: Sea bass, sea bream, salmon, trout, halibut, turbot, tilapia, cod,yellow tail,
turbot and ornamentals.
Manual for Micro/Macro Fiske teller
Page 24
1300 mm
1600
mm
Standard Counters
Single Channel Macro
Legs are adjustable for up to 500mm extra height.
Sizes are approx. for a standard counter.
4 Channel Macro Quattro
2800 mm
1000
mm
Manual for Micro/Macro Fiske teller
Page 25
The Macro counter is split into 4 separate counting
channels. The channel dividers in the inlet can be
removed and the upwelling inlet used to convert to single
channel for fast deliveries.
Single Channel Micro
The counting channel is 500mm wide x 70mm deep. The Micro can also supplied as a 3 channel counter.
2300 mm
500 m
m
Top Related