<dpwsp;Check that the CP is in parallel, CP-B should be
executive.
Command: DPWSP;
Command:EXRPP:RP=ALL;
Printout: RP DATA
2. Make sure that RP software are defined. There should at least be
REXR/RGEXR, RPFDR and application software defined. .
Command: EXRUP: RP=ALL;
Printout: RP SOFTWARE UNIT DATA
3. Check that the magazine address and RP numbers are
defined.
Command: DBTSP: TAB=RPSRPBSPOS;
Printout: DATA BASE TABLE
Note:
Test all RPs on one RP-bus at a time.
RPs of type RPG are manually blocked after test for safety
reasons.
1. Connect the selected RP-bus to all RPs and power on all
RPs.
2. Deblock one RP.
Command: BLRPE: RP=rp;
Printout: DEBLOCKING OF RP
Command: EXRPP: RP=rp;
Printout: RP DATA
******************************************************************************************************************************
6. Halt one CP-side. Watch out for any RPs going ABL, since this
might indicate swapped A- and B-path RP-buses.
Repair any faults found.
Command: DPPAI;
8. Switch CP sides, so that CP B-side becomes executive.
C11ommand: DPSWI;
Printout: CP STATE
10.Print the status of all RPs, if any RP is in state ABL, correct
all faults and bring the RPs back into service by using commands
REMRI and RECRI.
Command: EXRPP: RP=ALL;
Command: DPPAI;
**************************************************************************************************************************************************
Command: DPWSP;
Printout: CP STATE
2. Request for manual intervention. Follow the actions given in the
printout (except replace the MAU board).
Command: REMCI:MAG=CPU-B,PCB=MAU;
Printout: CP MANUAL INTERVENTION
Command: DPWSP;
Command: RECCI;
Printout: CP REPAIR
5. Suspend forced EX selection. Switch on power in CP-B. Order
updating to parallel working state.
Command: RECCI;
Printout: CP REPAIR
6. Check that the CP is in parallel, CP-A should be
executive.
Command: DPWSP;
Command: DPSWI;
Printout: CP STATE
2. Check that the CP is in parallel, CP-B should be
executive.
Command: DPWSP;
Printout: CP STATE
3. Request for manual intervention. Follow the actions given in the
printout (except replace the MAU-board).
Command: REMCI:MAG=CPU-B, PCB=MAU;
Printout: CP MANUAL INTERVENTION
Command: DPWSP;
Command: RECCI;
Printout: CP REPAIR
6. Suspend forced EX selection. Suspend on power in CP-A. Order
updating to parallel working state.
Command: RECCI;
Printout: CP REPAIR
7. Check that the CP is in parallel, CP-A should be
executive.
Command: DPWSP;
Switch on power in CP-A. Red LED "FEX" should be lit.
Check that the reloading begins after a few minutes:
For APG40: The ACT LED's on the LBB/RAID board should flash
indicating activity.
Wait until loading is done and a restart is made in CP-A.
2. Switch on power in the MAU. Order start-up of the MAU.
Command: RECCI;
Printout: CP REPAIR
3. Switch on power in CP-B. Order updating to parallel working
state.
Command: RECCI;
Printout: CP REPAIR
4. Check that the CP is in parallel, CP-A should be
executive.
Command: DPWSP;
Command: CACLS: DAY=day, TIME=hhmm, DATE=yymmdd;
6. Order a small restart to set the time in all APT blocks, job
buffers and time queues. Printout will appear on terminal defined
for PRCA=32.
Command: SYREI: RANK=SMALL, EXPL=expl;
Printout: RESTART DATA
Command: DPWSP;
Switch on power in CP-B. Red LED "FEX" should be lit.
Check that the reloading begins after a few minutes:
For APG40: The ACT LED's on the LBB/RAID board should flash
indicating activity.
Wait until loading is done and a restart is made in CP-B.
2. Switch on power in the MAU. Order start-up of the MAU.
Command: RECCI;
Printout: CP REPAIR
3. Switch on power in CP-A. Order updating to parallel working
state.
Command: RECCI;
Command: CACLS:DAY=day,TIME=hhmm, DATE=yymmdd;
5. Order a small restart to set the time in all APT blocks, job
buffers and time queues. Printout will appear on terminal defined
for PRCA=32.
Command: SYREI:RANK=SMALL(,EXPL=expl);
Command: DPWSP;
Command: ALLIP;
Command: SYCLI;
5. Take action to other alarms according to relevant OPIs.
6. Sign this Start Up case in the report:
Start Up Report, AXE 810, 69/1532-B/AXE 106 99 Uen
*****************************end*********************************************************************************************************************************************