TURAP (DINDING PENAHAN LENTUR) - yulvi.lecture.ub.ac.id · Dapat memilih model turap yang sesuai...
-
Upload
truongliem -
Category
Documents
-
view
412 -
download
38
Transcript of TURAP (DINDING PENAHAN LENTUR) - yulvi.lecture.ub.ac.id · Dapat memilih model turap yang sesuai...
TURAP (DINDING PENAHAN LENTUR)
YULVI ZAIKA
LEARNING OUTCOMES
• Mengetahui penggunaan dinding penahan turap
• Dapat memilih model turap yang sesuai dengan kondisi lapangan
• Menrencanakan maerial, dimensi dan tipe turap
• Pelaksanaan penginstalan turap dilapangan
TURAP KAYU
TURAP BETON
TURAP BAJA
Cofferdams
• Traditional Sheet Pile Shapes
Z-Type (Z)
Used for intermediate to deep
wall construction
Larson / “U” Type (U)
Used for applications similar to Z - Type
Flat / Straight Type (SA), (S)
Used for filled cell constructionArch shaped & lightweight
Used for shallower wall construction
7
Cofferdams• Typical types of interlocks
Ball & Socket (BS) Single Jaw (SJ) Double Jaw (DJ)
Hook & Grip (HG) Thumb & Finger
one point contact (TFX)
Double Hook (DH)Thumb & Finger
three point contact (TF)
SECTIONTYPE
Width Height Thickness Section Weight WeightMoment
ofModulus o
fw h t Area perpile per wall Inertia Scetion
mm mm mm cm2/m kg/m kg/m2 cm4/m cm3/mSLU5-1 600 150 9.5 119.7 56.4 94 3825 510SLU5-2 600 150 10 126.1 59.4 99 4050 540SLU6-1 600 280 6 90 42.2 70 8940 640SLU7-1 600 300 6 93.4 44 73 9585 690SLU7-2 600 340 6 98 46.2 77 11525 745SLU7-3 600 360 6 99.6 46.9 78.2 11360 740
Tipe U
Single Pile
SectionsWidth(a
)Thickness(t)
Deviation Angle
Steel Section
Mass per m
Mass per m2
Moment of Inertia
Modulus of Section
mm mm o kg/m kg/m2 cm4/m cm3/mSLT1 500 9.5 4.5 81 63.6 127.2 167 45SLT2 500 11 4.5 90 70.5 141 185 48SLT3 500 12 4.5 94.3 74 148 195 50.5SLT4 500 12.5 4.5 96.8 76 152 205 51SLT5 500 12.7 9.5 98 77 154 206 51.5
Straight Type
SectionType
Width Height Thickness Section Weight WeightMoment
ofModulus of
w h t Area Perpile perwall Inertia Section
mm mm mm cm2/m kg/m kg/m2 cm4/m cm3/m
SLZ13-1 670 303 9.5 137 72 107 19700 1300
SLZ13-2 770 344 9 126 76.1 99 22360 1300
SLZ13-3 575 260 10.8 150.3 67.9 118 16250 1250
SLZ14-1 670 304 10.5 149 78.3 117 21300 1400
SLZ14-2 770 345 9.5 132 79.5 103 23300 1355
SLZ14-3 770 345 10 137 82.9 108 24240 1405
SLZ17-3 575 370 8.5 142.8 64.5 112 28890 1655
SLZ17-4 575 370 9 148.2 66.9 116 30110 1725
SLZ17-5 575 350 9.5 149 67.3 117 29760 1705
SLZ14-4 700 420 7 112.8 62 88.6 30910 1480
SLZ14-5 650 320 8 127.4 65 100 22049 1380
Tipe Z
VINYL
Vinyl (composite)sheet piles is applicated to replace traditional
steel, timber and concrete piling. Its much cheaper and durable for years
Cross Section Turap
PENGGUNAAN TURAP
• DINDING PENAHAN UNTUK DERMAGA
• BASEMENT
• PENAHAN SEMENTARA UNTUK PEKERJAAN BAWAH TANAH
• DINDING PENAHAN SUNGAI
PELAKSANAAN UNTUK STRUKTUR URUGAN
Struktur Urugan
Struktur Galian
Efek Pelaksanaan pada Tanah
• Galian
• reduksi overburden
• tegangan efektif lebih kecil
• timbul tekanan air pori negatif
• tanah menjadi lebih lunaksetelah disipasi air pori
• harus menggunakan effectivestrengths dan stresses
• Timbunan
• kenaikan overburden
• tegangan efektif ; lebih besar
• timbul tekanan air pori positif
• tanah konsolidasi dan menjadilebih kuat setelah disipasi air pori
• Mula-mula tanah lunak
Tegangan Lateral
• Tekanan Lateral: 𝜎ℎ = 𝐾 𝜎𝑣 dimana
• Dimana:
• K= koefisien tegangan lateral
• ko = tekanan tanah lateral kondisi diam
• ka= tekanan tanah lateral aktif
• kp= tekanan tanah lateral pasif
• 𝜎𝑎 = 𝐾𝑎𝜎𝑣 − 2𝑐 𝐾𝑎
• 𝜎𝑝 = 𝐾𝑝𝜎𝑣 + 2𝑐 𝐾𝑝
H
g HKa
pa
H/3
45+f/2
45-f/2
DIAGRAM TEGANGAN AKTIF DAN PASIF
−2𝑐 𝐾𝑎
𝐾𝑎𝛾𝐻 − 2𝑐 𝐾𝑎
2𝑐 𝐾𝑝
𝐾𝑝𝛾𝐻 + 2𝑐 𝐾𝑝 𝐾𝑎𝛾𝐻
Tanah non kohesifTanah kohesif
2𝑐 𝐾𝑎
Jenis Turap
• Turap cantilever
di tanah pasir dan lempung
• Turap berjangkar (anchored sheet pile)
• Free earth support
• Fixed earth support