TBD-309LNb/ML-305HS application test report · AWS A4.2M 堆焊层表面 3-8 实测值Measured ....
Transcript of TBD-309LNb/ML-305HS application test report · AWS A4.2M 堆焊层表面 3-8 实测值Measured ....
TBD-309LNb/ML-305HS application test report
0
不锈钢带极单层高速电渣堆焊 High Speed ESW Strip Cladding
TBD-309LNb/ML-305HS
焊后热处理(PWHT) 665℃×12hr+705℃×32hr
应用试验报告 Application Test Report
ITW 焊接集团亚洲技术中心
ITW Welding Asia R&D Center
TBD-309LNb/ML-305HS application test report
1
1. 试验焊材 / welding consumables
品名
Consumables 规格 Size
批号 Lot.
标准 Spec. No.
型号 Class
生产商 Manufacturer
TBD-309LNb 0.5×60 404197 NB/T 47018.5 EQ309LNb 天泰(台湾)
ML-305HS / 21010 NB/T 47018.5 / 天泰(台湾)
2. 焊带化学成分 / Chemical composition of strip
C Si Mn P S Cr Ni Mo Nb Cu
NB/T 47018 EQ309LNb
0.030 1.00 0.50- 2.50
0.025 0.015 21.00- 25.00
9.00- 14.00
- 8*C- 1.0
0.75
TBD-309LNb 0.018 0.30 2.17 0.019 0.001 24.4 12.2 0.05 0.71 0.05 * 标准中单个值为最大值 3. 堆焊试验 / Cladding test 3.1 焊接工艺 / Welding process
焊接方法 Welding Process
单层高速电渣堆焊 H-ESW
焊接位置 Welding position
平焊(1G)
母材材质及尺寸 Base Metal
EH36+ TWE-911B3(1.2) 400╳400╳30mm
焊机型号 Power Source
Miller Subarc DC 1250 Two sets
TBD-309LNb/ML-305HS application test report
2
3.2 焊接参数 / Welding parameters
焊接示意图 Welding Diagram
层次 Layer
道数 Pass
电流 Current(A)
电压 Voltage(V)
道间温度 Interpass temp.(℃)
焊接速度 WS(mm/min)
热输入 HI(KJ/cm)
1st layer 1 1900 24 RT 350 78.2 1st layer 2 1900 24 90 350 78.2 1st layer 3 1900 24 140 350 78.2 1st layer 4 1900 24 167 350 78.2 1st layer 5 1900 24 175 350 78.2
3.3 焊接图片 / Welding photos
第一层第一道 First pass of first layer
所有焊道 All pass
TBD-309LNb/ML-305HS application test report
3
3.4 堆焊层化学成分 / Chemical composition of deposit
位置 Test Position
C Si Mn P S Cr Ni Mo Cu Nb N
NB/T 47018.5 FZ347-D
0.05 1.00 2.5 0.030 0.020 18.0- 21.0
9.0- 12.0
-- 0.75 8*C-
1.00 -
4.8mm surface
0.033 0.68 1.46 0.015 0.004 18.4 9.7 0.28 0.04 0.46 0.04
3.0mm beneath
0.033 0.66 1.45 0.015 0.005 18.6 9.8 0.28 0.04 0.45 0.04
* 标准中单个值为最大值 * 表面下 3mm 的成分经 WRC 1992 计算后的 FN=6 3.5 堆焊层铁素体 / Ferrite content (AW)
试验方法 Test spec.
测试位置 Test position
铁素体含量 content
平均值 Avg
标准值 Standard Magnetic method of
AWS A4.2M
堆焊层表面 3-8
实测值 Measured 距母材 4.8mm FN:8.1、7.9、6.3、6.5、6.3 7.0
TBD-309LNb/ML-305HS application test report
4
3.6 堆焊层耐腐蚀试验 / Corrosion resistance test of cladding layer (PWHT)
试验结果 Test result
根据 ASTM A262 E 法标准试验(尺寸:80╳10╳3mm),两片腐蚀片均合格。 According to the ASTM A262 E (Size: 80╳10╳3mm), the two samples are OK.
3.7 堆焊层侧弯试验 / Side bend test (PWHT)
编号 No.
试样类型 Sample type
试样厚度 Sample
thickness
弯心直径 Diameter
(mm)
弯曲角度 Bend angle
(°)
试样个数 Quantity
试验结果 Test result
1 横向大侧弯
Transverse side bend(big) 10 40 180° 2
两片无裂纹 OK
2 横向小侧弯
Transverse side bend(small) 3 12 180° 2
两片无裂纹 OK
3 纵向大侧弯
Longitudinal side bend(big) 10 40 180° 2
两片无裂纹 OK
4 纵向小侧弯
Longitudinal side bend(small) 3 12 180° 2
两片无裂纹 OK
3.8 硬度 / Hardness (PWHT) PWHT 测试位置 Test position 硬度值 Hardness 平均值 AVG:
标准值 Standard 248
实测值 Measured 665℃×
12hr+705℃×32hr
Surface (4.8mm) 232、219、226、233、233 229 Section (Corrosion resistant) 215、224、216、235、228 220
Section (welding line) 237、234、194、216、199 216 Section (HAZ) 226、230、228、231、236 230
TBD-309LNb/ML-305HS application test report
5
侧弯照片
横向大侧弯(1) 横向大侧弯(2)
纵向大侧弯(1) 纵向大侧弯(2)
横向小侧弯 纵向小侧弯