Priloga k akreditacijski listini (Kalibracijski laboratoriji) hidrometri / Areometers; o OPTIČNE...
Transcript of Priloga k akreditacijski listini (Kalibracijski laboratoriji) hidrometri / Areometers; o OPTIČNE...
OB05-32 Izdaja 7 Stran 1 od 46
Reg. št. / Ref. No.: 3150-0013/10-0020
Datum izdaje / Issued on: 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated: 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si. Information on current accreditation status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI Annex to the accreditation certificate
LK-008
1 AKREDITIRANI ORGAN / Accredited body
LOTRIČ Meroslovje d.o.o. / LOTRIČ Metrology Ltd.
Selca 163, 4227 Selca
2 STANDARD
SIST EN ISO/IEC 17025:2005
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu
usposobljenost za opravljanje naslednjih dejavnosti: / SA hereby acknowledges the accredited body
as being competent for performing the following activities:
3.1 Skrajšani opis obsega akreditacije / A short description of the scope
Kalibriranje na naslednjih področjih in naštetih pod-področjih (Calibration in the following fields and
the specified sub-fields):
o ČAS IN FREKVENCA / TIME AND FREQUENCY:
• Časovni interval / Time interval:
▪ merilniki časa / Timers;
• Tahometri / Tachometers:
▪ oprema za kontrolo tahografov, naprave za kontrolo hitrosti, merilniki obratov /
Equipment for Tachograph inspection, Speedometers, Tachometers;
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 2 od 46
o DIMENZIONALNE VELIČINE / DIMENSIONAL QUANTITIES:
• Dolžina / Length:
▪ Merila dolžine: mejna vzporedna merila – merilne kladice, kvadratne in okrogle merilne
kladice, planparalelna stekla, stopničasti etaloni, merilne urice, merilniki globine
pnevmatik, elektronska tipala, debelinska merila, zevna merila / Length gauges: Gauge
blocks, Square and Cylindrical gauge blocks, Optical plats, Step gauges, Dial gauges,
Tire depth gauges, Electronic probes, Thickness gauges, Gap gauges;
▪ Črtna merila: toga črtna merila, tračna merila / Line scales, distances: Rulers, Tape
measures;
▪ Instrumenti za merjenje dolžine: dvotočkovna vijačna merila (zunanja in notranja),
pomična merila, laserski merilniki razdalje, ultrazvočni merilniki debeline, magnetni
merilniki debeline, cestna merilna kolesa, merilna kolesa s števcem, preskusna sita,
merilniki izteka koles / Length measuring instruments: two point micrometers (internal
and external), Vernier calliper gauges, Laser distance meters, Ultrasonic thickness
meters, Magnetic thickness meters, Distance measuring wheels, Measuring wheels with
counters, Test sieves, Wheel alignment testers;
▪ Premer - notranji premer: tritočkovna vijačna merila, merilni obroči, merilni konusni
obroči; - zunanji premer: merilni trni, merilni konusni trni, merilne krogle / Diameter -
Internal diameter: Tree point micrometers, Ring gauges, Ring taper gauges; - External
diameter: Plug gauges, Plug taper gauges, Sphere (ball) diameter;
▪ Obseg - Instrumenti za merjenje oblik – notranji obseg (premer) / Circumference –
Contour measuring instruments – inside circumference (diameter);
▪ Odstopanje oblike: merilne plošče, ravnila (ravnost in vzporednost) / Form error: Surface
plates, Rulers (flatness and parallelism);
▪ Hrapavost: instrumenti za merjenje hrapavosti / Roughness: Instruments for roughness;
▪ Navojne veličine: navojni obroči in trni, navojni konusni obroči in trni / Tread quantities:
Screw plug and ring gauges, Screw taper plug and ring gauges;
▪ Koordinatni merilni stroji: 1D naprave, 2D naprave, 3D naprave / Co-ordinate measuring
machines: 1D machines, 2D machines, 3D machines;
• Kot / Angle:
▪ Merila kota: Kotna mejna merila – kotne kladice, sinusna ravnila / Angle gauges: Angle
gauge blocks, Sine bars;
▪ Merilniki kota: kotniki, kotomeri / Angle gauges: Squares, Protractors;
▪ Merilniki nagiba / Clinometers;
o MEHANSKE VELIČINE / MECHANICAL QUANTITIES:
• Sila / Force:
▪ pretvorniki sile, merilni stroji za merjenje sile, merjenje položaja prečke, stiskalnice za
beton, vzvodi za kalibracijo naprav z valji za preverjanje zaviralne sile, naprave z valji za
preverjanje zaviralne sile / Force transducers, Force measuring machines, Position
measurement of the crosshead, Concrete testing machines, Levers for calibration of roll
brake testers, Roll brake testers;
▪ Mehanska energija / Mechanical energy:
▪ Merilniki udarne žilavosti / Pendulum impact machines;
• Masa (konvencionalna) / Conventional Mass:
▪ etalonske uteži, predmeti ostalih poljubnih mas / Standard weights, Objects of any other
mass;
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 3 od 46
• Tehtnice / Weighing Instruments:
▪ neavtomatske tehtnice / Non-automatic weighing instruments;
• Tlak / Pressure:
▪ relativni tlak (negativni in pozitivni): merilniki krvnega tlaka, merilniki tlaka v
pnevmatikah, mehanski, elektromehanski in tekočinski manometri / Pressure gauges
(negative and positive): Sphygmomanometers, Tire pressure manometers, Mechanical,
Electromechanical and Liquid manometers;
▪ Absolutni tlak: mehanski, elektromehanski in tekočinski manometri / Atmospheric
pressure: Mechanical, Electromechanical and Liquid barometers
▪ Ovrednotenje komor: parni sterilizatorji, avtoklavi, tlačne komore / Evaluation of
chambers: devices: steam sterilizers, autoclaves, pressure chambers;
• Moment sile / Torque:
▪ Momentni ključi / Torque wrenches
• Pospešek / Acceleration:
▪ Merilniki pojemkov in pospeškov, kalibratorji pospeškomerov / Acceleration and
deceleration measuring instruments, Accelerometer Calibrators;
• Trdota / Hardness:
▪ Merilniki trdote: Shore, IRHD, Brinell, Vickers, Rockwell / Hardness testers: Shore,
IRHD, Brinell, Vickers, Rockwell;
• Masno uravnoteženje / Mass balance:
▪ Stroji za uravnoteženje pnevmatik / Wheel balancing machine;
o AKUSTIČNE VELIČINE / ACOUSTICAL QUANTITIES:
• Raven zvočnega tlaka / Sound pressure level:
▪ merilniki zvočnega tlaka, akustični kalibratorji, korekcijski faktor mikrofona, pistonfoni,
merilniki popačenja / Sound level meters, Acoustical calibrators, Microphone correction
factor, Piston-phone, Distortion analysers;
• Pretvorniki zvočnega tlaka / Transducers of sound level pressure:
▪ merilnika zvočnega tlaka (električni del), pretvorniki zvočnega tlaka, merilniki zvoka /
Sound lever meters (electrical part), Microphone sound level meters, Sound level
meters;
• Pretvorniki vibracij in sile / Vibration and force transducers:
▪ umetni mastoidi, merilniki vibracij / Artificial mastoids, Vibration meters;
o FLUIDNE VELIČINE / FLUID QUANTITIES:
• Hitrost plinov in tekočin / Gas and fluid flow rate
▪ merilniki hitrosti zraka / Anemometers
• Volumen pretoka plinov in tekočin / Volume of flowing gases and liquids:
▪ Prostorninski tok plina, volumetrični dozirni sistemi / Gas volume flow rate, Volumetric
dosing systems
• Volumen tekočin / Volume of Liquids:
▪ pipete (enokanalne in večkanalne), dispenzorji in batne birete (razdeljevalci), sistemi za
avtomatsko pipetiranje (ALHS), steklene merilne in polnilne pipete, birete in steklenice
za merjenje gostote, merilni valji in steklenice, volumske posode, volumen teles,
porozimetri, / Pipettes (single and multi-channel), Dispensers and burettes, Automated
liquid handling systems (ALHS), Glass graduated and Bulb pipette (Titrators),
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 4 od 46
Volumetric flash, Burette and Density bottles – Pycnometers, Graduated cylinders and
Bottles, Volume vessels, Body volume, Porosimeters;
• Gostota / Density:
▪ gostotni hidrometri / Areometers;
o OPTIČNE VELIČINE / OPTICAL QUANTITIES:
• Lastnosti optičnih sistemov / Optical system properties:
▪ merilniki prepustnosti svetlobe, regloskopi, merilniki sijaja / Tint meters, Regloscopes,
Glossmeters;
o TEMPERATURA, VLAGA IN TERMO FIZIKALNE LASTNOSTI / TEMPERATURE, HUMIDITY,
AND THERMO-PHYSICAL PROPERTIES:
• Temperatura / Temperature:
▪ Uporovni termometri / Resistance thermometers;
▪ Termočleni / Thermocouples;
▪ Tekočinski termometri / Liquid-in-glass thermometers:
▪ Termometri s prikazovalniki / Thermometers with indicators,
▪ Indikatorji in simulatorji uporovnih termometrov in termočlenov / Resistance
thermometers and Thermocouple indicators and simulators;
▪ Sevalni termometri, ušesni termometri / Radiation thermometers, Ear thermometers:
• Vlažnost / Humidity:
▪ merilniki relativne vlažnosti / Relative humidity sensors;
• Ovrednotenje klimatsko reguliranih komor / Evaluation of climatic controlled chambers;
▪ klimatske komore (temperatura in relativna vlaga): Stabilizatorji, sušilniki, vakuumski
sušilniki, termostatirane komore in prostori, hladilniki, zamrzovalne skrinje, kopeli /
Climatic chambers (temperature and relative humidity): Stabilizers, Dryers, Vacuum
dryers, Thermostat chambers and rooms, Refrigerators, Freezers, Baths;
▪ parni sterilizatorji, avtoklavi / Steam sterilizers, autoclaves;
▪ temperaturne kalibracijske kopeli / Temperature calibration baths,
▪ temperaturni suhi kalibratorji / Temperature block calibrators,
▪ peči / Furnaces;
o KEMIJSKA ANALIZA, REFERENČNI MATERIALI / CHEMICAL ANALYSIS, REFERENCE
MATERIALS:
• Instrumenti za analizo, monitoring / Analytical instruments, monitors:
▪ merilniki izpušnih plinov, merilniki izpušnih plinov na kompresijski vžig / gas exhaust
analysers, diesel exhaust analysers;
▪ merilniki pH, merilniki prevodnosti tekočin, merilniki slanosti / pH meters, Conductivity
measuring equipment, Salinity meters;
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 5 od 46
3.2 Podrobni opis obsega akreditacije / Detailed scope of accreditation
3.2.1 LOTRIČ Meroslovje d.o.o. / LOTRIČ Metrology Ltd., Selca 163, 4227 Selca
Tabela / Table 1 – kalibracije v laboratoriju / in-lab calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
ČAS IN FREKVENCA
TIME AND FREQUENCY
Časovni interval
Time interval
ƒ = merjena vrednost frekvence / measured value of frequency
Merilniki časa
Timers
- interni postopek / internal procedure:
ML10N111
1. Čas
Time
24 h 0,1 s
Tahometri
Tachometers
Oprema za kontrolo tahografov Equipment for Tachograph inspection
- interni postopek / internal procedure: ML10N113
2. Hitrost Speed
(13 do/ to 1200) Hz (20 do/ to 180) km/h
0,04 Hz + 0,0003·ƒ
3. Prevožena pot Travelled distance
(1000 do/to 10000) m 0,2 %
4. Časovni interval
Time interval
24 h
0,1 s / 24 h
Merilniki obratov Tachometers
- interni postopek / internal procedure: ML10N138
5. do/ to 60 min-1 0,01 min-1
6. (60 do/ to 300) min-1 0,05 min-1
7. (300 do/ to 600) min-1 0,07 min-1
8. (600 do/ to 5000) min-1 0,5 min-1
9. (5000 do/ to 10000) min-1 0,7 min-1
10. (10000 do/ to 30000) min-1 5 min-1
11. (30000 do/ to 60000) min-1 6 min-1
12. (60000 do/ to 99999) min-1 7 min-1
DIMENZIONALNE VELIČINE
DIMENSIONAL QUANTITIES
Dolžina
Length
Merila dolžine
Length gauges L – merjena dolžina / measured length
Mejna vzporedna merila – merilne kladice Gauge Blocks
- interni postopek / internal procedure: ML10N76
13. (0,5 do/ to 5) mm 50 nm ISO 3650:1998
14. (5 do/ to 100) mm 45 nm + 1·10-6·L
15. 125 mm 325 nm
16. (150 do/ to 1000) mm 200 nm + 1,5·10-6·L
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 6 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Mejna vzporedna merila – kvadratne in okrogle merilne kladice Square and Cylindrical Gauge Blocks
- interni postopek / internal procedure: ML10N76
17. (0,5 do/ to 1000) mm 100 nm + 1,6·10-6·L ISO 3650:1998
Mejna vzporedna merila – planparalelna stekla Gauge blocks – optical flats
- interni postopek / internal procedure: ML10N76
18. (5 do/ to 100) mm 100 nm + 1,6·10-6·L VDI/VDE/DGQ 2618:2007
Stopničasti etaloni Step gauges
- interni postopek / internal procedure: ML10N91
19. (2 do/ to 1000) mm 1,2 μm + 6,5·10-5·L Merilna površina / Measuring area: < 100 mm x 100 mm
Merilne urice Dial gauges
- interni postopek / internal procedure: ML10N91
20. do/ to 100 mm 0,4 μm + 2·10-5·L ISO 463:2006 ISO 13102:2012 ISO 9493:2010 VDI/VDE/DGQ 2618:2007
Merilniki globine pnevmatik Tire depth gauges
- interni postopek / internal procedure: ML10N89
21. do/ to 100 mm 0,03 mm
Elektronska tipala Electronic probes
- interni postopek / internal procedure: ML10N91
22. do/ to 200 mm 0,4 μm + 2·10-5·L ISO 13102:2012 VDI/VDE/DGQ 2618:2007
Debelinska merila Thickness gauges
- interni postopek / internal procedure: ML10N91
23. do/ to 1000 mm 0,3 μm + 6,5·10-6·L Merilna površina / Measuring area: < 100 mm x 100 mm
Zevna merila Gap gauges
- interni postopek / internal procedure: ML10N91
24. (2 do/ to 1000) mm 1,2 μm + 6,5·10-6·L Merilna površina / Measuring area: < 100 mm x 100 mm
Črtna merila
Line Scales
Toga črtna merila Rulers
- interni postopek / internal procedure: ML10N85
25. do/ to 300 mm 0,6 μm + 4,5·10-6·L
26. do/ to 1000 mm 3,5 μm + 5·10-6·L
27. (1000 do/ to 4000) mm 50 μm + 3·10-6·L
Tračna merila Tape measures
- interni postopek / internal procedure: ML10N85
28. do/ to 200 m 50 μm + 3·10-6·L
Instrumenti za merjenje dolžine
Length measuring instruments
Dvotočkovna vijačna merila (zunanja in notranja) Two point Micrometers (external and internal)
- interni postopek / internal procedure: ML10N74
29. do/ to 2000 mm 1,0 μm + 4,5·10-6·L ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 7 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Pomična merila Calliper gauges
- interni postopek / internal procedure: ML10N72
30. do/ to 3000 mm 3,5 μm + 1·10-6·L ISO 13385:2011 ISO 13225:2012 VDI/VDE/DGQ 2618:2007
Laserski merilniki razdalje Laser distance meters
- interni postopek / internal procedure: ML10N85
31. do/ to 4000 mm 0,1 mm
32. (4 do/ to 60) m 1,25 mm + 5·10-5·L
Ultrazvočni merilniki debeline Ultrasonic thickness gauges
- interni postopek / internal procedure: ML10N120
33. do/ to 50 mm 15 µm + 4·10-3·L
Magnetni merilniki debeline Magnetic thickness gauges
- interni postopek / internal procedure: ML10N120
34. do/ to 12,5 mm 1,7 µm
Cestna merilna kolesa, merilna kolesa s števcem Distance measuring Wheels, Measuring wheels with counters
- interni postopek / internal procedure: ML10N96
35. do/ to 1000 m 2 mm + 1,5·10-4·L
Preskusna sita Test Sieves
- interni postopek / internal procedure: ML10N107
36. do/ to 400 mm 3,8 µm + 5·10-6·L ISO 3310-1:2000 ISO 3310-2:1999
Premer
Diameter
Notranji premer
Internal diameter
Tritočkovna vijačna merila Three point Micrometers
- interni postopek / internal procedure: ML10N74, ML10M75
37. (2 do/ to 300) mm 1,3 μm + 5,0·10-6·L ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Merilni obroči Ring gauges
- interni postopek / internal procedure: ML10N91
38. (2 do/ to 800) mm 1,2 μm + 6,5·10-6·L
Merilni konusni obroči Ring taper gauges
- interni postopek / internal procedure: ML10N91
39. (2 do/ to 300) mm 5,5 μm + 2,5·10-4·L
40. Konus / Taper 0,5 ´
Zunanji premer
External diameter
Merilni trni Plug gauges
- interni postopek / internal procedure: ML10N91
41. do/ to 300 mm 0,3 μm + 6,5·10-6·L
Merilni konusni trni Plug taper gauges
- interni postopek / internal procedure: ML10N91
42. do/ to 300 mm 5,5 μm + 2,5·10-4·L
43. Konus / Taper 0,5 ´
44. Merilne krogle Sphere (Ball) diameter
do/ to 100 mm 0,3 μm + 6,0·10-6·L
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 8 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Obseg
Circumference
Notranji obseg
Internal circumference
Instrumenti za merjenje oblik – notranji obseg Contour measuring instruments – inside circumference
- interni postopek / internal procedure: ML10N74
45. Premer / diameter (2 do/ to 300) mm 3,6 μm + 2,5·10-6·L
Odstopanje oblike
Form error
Merilne plošče Surface Plates
- interni postopek / internal procedure: ML10N101
46. Ravnost Flatness
3 μm Merilna površina / Measuring area: < 500 mm x 700 mm
Ravnila Rulers
- interni postopek / internal procedure: ML10N87
47. Ravnost in vzporednost Flatness and parallelism
3 μm Dolžina / Length: < 1000 mm
Hrapavost
Roughness
Instrumenti za merjenje hrapavosti Instruments for Roughness measurement
- interni postopek / internal procedure: ML10N145
48. (0,065 do/ to 1,63) μm 0,05 µm + 7·10-2 Ra
Navojne veličine
Thread quantities
Navojni obroči Screw Ring gauges
- interni postopek / internal procedure: ML10N91
Srednji premer Simple Pitch diameter
(2,5 do/ to 300) mm Korak v območju / Pitch in range: (0,35 do/ to 6) mm
= bočni kot / Thread angle po / according to: EURAMET / cg-10 / v2.1 / 2011 - metoda / method: 1a
49. = 30 ° 5,0 μm + 2·10-5·L
50. = 55 ° 3,0 μm + 5·10-6·L
51. = 60 ° 3,5 μm + 3·10-6·L
Navojni trni Screw Plug gauges
- interni postopek / internal procedure: ML10N91
Srednji premer Simple Pitch diameter
(0,8 do/ to 300) mm Korak v območju / Pitch in range: (0,2 do/ to 6) mm
= bočni kot / Thread angle po / according to: EURAMET / cg-10 / v2.1 / 2011 - metoda / method: 1a
52. = 30 ° 5,0 μm + 2·10-5·L
53. = 55 ° 3,0 μm + 5·10-6·L
54. = 60 ° 3,5 μm + 5·10-6·L
Navojni konusni obroči Screw taper Ring gauges
- interni postopek / internal procedure: ML10N91
Srednji premer Simple Pitch diameter
(2,5 do/ to 280) mm Korak v območju / Pitch in range: (0,5 do/ to 6) mm
= bočni kot / Thread angle
55. = 55 ° 4,0 μm + 2,1·10-4·L
56. = 60 ° 5,5 μm + 2,0·10-4·L
57. Konus / Taper 0,5 ´
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 9 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Navojni konusni trni Screw taper Plug gauges
- interni postopek / internal procedure: ML10N91
Srednji premer Simple Pitch diameter
(0,8 do/ to 280) mm Korak v območju / Pitch in range: (0,5 do/ to 6) mm
= bočni kot / Thread angle
58. = 55 ° 4,0 μm + 2,1·10-4·L
59. = 60 ° 5,5 μm + 2,0·10-4·L
60. Konus / Taper 0,5 ´
Koordinatni merilni stroji
Co-ordinate measuring machines
1D naprave 1D machines
- interni postopek / internal procedure: ML10N109
61. do/ to 1000 mm 0,2 µm + 4·10-6·L
2D naprave 2D machines
- interni postopek / internal procedure: ML10N109
62. do/ to (200 x 300) mm 1,5 µm + 3·10-6·L
3D naprave 3D machines
- interni postopek / internal procedure: ML10N109
63. do/ to (1500 x 1500) mm 1,0 µm + 2,5·10-6·L
Kot
Angle
Merilniki kota
Angle gauges
Kotne kladice Angle gauges
- interni postopek / internal procedure: ML10N98
64. do/ to 360 ° 6 ˝
Sinusna ravnila Sine bars
- interni postopek / internal procedure: ML10N185
65. do/ to 500 mm Razdalje Distances Ravnost, vzporednost Flatness, parallelism
1,6 µm + 6,5·10-6·L 3,0 µm
BS 3064:1978
Kotomer Protractor
- interni postopek / internal procedure: ML10N87
66. do/ to 360 ° 15 ˝
Kotniki Squares
- interni postopek / internal procedure: ML10N98
67. Pravokotnost Squarness
6 ˝ Velikost kotnika / Size of Squares:
(500 x 1000) mm
Merilniki nagiba Clinometers
- interni postopek / internal procedure: ML10N99
68. (- 5 do/ to 5) mm/m 25 μm/m
69. (- 0,8 do/ to 0,8) ° 5 ˝
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Sila
Force
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 10 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Pretvorniki sile Force transducers
- interni postopek / internal procedure: ML10N47
70. (>1 do/ to 10) N 0,011 N
71. (10 do/ to 400) N 0,11 N
72. (400 do/ to 600) N 0,12 N
73. (600 do/ to 1000) N 0,13 N
74. (1000 do/ to 2000) N 1,1 N
75. (2000 do/ to 2500) N 1,2 N
76. (2500 do/ to 5000) N 3,5 N
Vzvodi za kalibracijo naprav z valji za preverjanje zaviralne sile Levers for calibration of Roll brake testers
- interni postopek / internal procedure: ML10N124
77. do/ to 0,2 kN 0,7 % (ne/not < 1 N ) Vzvodi za naprave za osebna vozila in kolesa z motorjem Levers for car and moped roll brake testers
78. (0,2 do/ to 0,5) kN 0,5 %
79. (0,5 do/ to 2,0) kN 0,4 %
80. (0,2 do/ to 20) kN
0,4 %
Vzvodi za naprave za tovorna in priklopna vozila Levers for truck roll brake testers
Mehanska energija
Mechanical energy
Merilniki udarne žilavosti Pendulum impact machines
- interni postopek / internal procedure: ML10N168
81. (0,2 J do/ to 50) J ISO 13802:1999
82. Čas / Time 0,1 s
83. Kot / Angle 0,2 °
84. Sila / Force 0,2 % (ne/not < 0,02 N)
85. Dolžina / Length 0,2 % (ne/not < 0,02 mm)
Masa (konvencionalna)
Conventional Mass
Etalonske uteži Standard Weights
- interni postopek / internal procedure: ML10N02, ki temelji na / which is based on OIML R 111-1 (2004)
86. 1 mg 0,002 mg
87. 2 mg 0,002 mg
88. 5 mg 0,002 mg
89. 10 mg 0,002 mg
90. 20 mg 0,003 mg
91. 50 mg 0,004 mg
92. 100 mg 0,005 mg
93. 200 mg 0,006 mg
94. 500 mg 0,008 mg
95. 1 g 0,010 mg
96. 2 g 0,012 mg
97. 5 g 0,015 mg
98. 10 g 0,020 mg
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 11 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
99. 20 g 0,025 mg
100. 50 g 0,030 mg
101. 100 g 0,05 mg
102. 200 g 0,10 mg
103. 500 g 0,25 mg
104. 1 kg 1,5 mg
105. 2 kg 3,0 mg
106. 5 kg 7,5 mg
107. 10 kg 15 mg
108. 20 kg 30 mg
109. 50 kg 250 mg
Predmeti ostalih poljubnih mas
Objects of any other Mass
- interni postopek / internal procedure: ML10N02
110. do/ to 0,5 g 0,01 mg
111. (0,5 do/ to 5,1) g 0,03 mg
112. (5,1 do/ to 50) g 0,05 mg
113. (50 do/ to 205) g 0,1 mg
114. (205 do/ to 2000) g 3,0 mg
115. (2 do/ to 5) kg 5,0 mg
116. (5 do/ to 10,1) kg 7,0 mg
117. (10,1 do/ to 25) kg 25 mg
118. (25 do/ to 40) kg 80 mg
119. (40 do/ to 64,1) kg 120 mg
Tehtnice
Weighing instruments
m = masa / mass
Neavtomatske tehtnice
Non-automatic weighing instruments
- interni postopek / internal procedure: ML10N01, ki temelji na / which is based on EURAMET / cg-18 / v4.0 / 2015
120. do/ to 5 mg 0,0013 mg
121. (5 do/ to 10) mg 0,0015 mg
122. (10 do/ to 20) mg 0,0016 mg
123. (20 do/ to 50) mg 0,0020 mg
124. (50 do/ to 100) mg 0,0024 mg
125. (100 do/ to 200) mg 0,0030 mg
126. (200 do/ to 500) mg 0,0039 mg
127. (0,5 do/ to 1) g 0,0047 mg
128. (1 do/ to 2) g 0,0060 mg
129. (2 do/ to 5) g 0,0078 mg
130. (5 do/ to 10) g 0,011 mg
131. (10 do/ to 20) g 0,014 mg
132. (20 do/ to 50) g 0,018 mg
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 12 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
133. (50 do/ to 600) g m·(3,5·10-7)
134. (600 do/ to 25000) g m·(8,0·10-7)
135. (25 do/ to 100) kg m·(2,5·10-6)
136. (100 do/ to 600) kg m·(3,0·10-6)
Tlak
Pressure
Podtlak: mehanski in elektromehanski manometri Negative pressure gauge: Mechanical and electromechanical manometers
- interni postopek / internal procedure: ML10N31, ML10N55
137. (- 0,95 do/ to 0) bar 0,34 mbar EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij: plin, tekočina Medium: gas, fluid
Nadtlak: merilniki krvnega tlaka Positive pressure gauge: Sphygmomanometers
- interni postopek / internal procedure: ML10N31, ML10N55
138. (0 do/ to 300) mmHg 0,064 mmHg EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij:plin Medium: gas
139. (0 do/ to 40) kPa 8,5 Pa
Nadtlak: mehanski in elektromehanski manometri, merilniki tlaka v pnevmatikah Positive pressure gauge: Mechanical, Electromechanical and, Tyre pressure manometers
- interni postopek / internal procedure: ML10N31, ML10N55
140. (0 do/ to 2500) Pa 1,4 Pa + 1,9·10-3p EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij: plin, tekočina Medium: gas, fluid
141. 2500 Pa do/ to 17,5 bar 2 mbar
142. (17,5 do/ to 35) bar 2,5 mbar
143. (35 do/ to 160) bar 0,05 bar
144. (160 do/ to 1000) bar 0,32 bar
Absolutni tlak: mehanski, elektromehanski in tekočinski barometri Atmospheric pressure: Mechanical, Electromechanical and Liquid barometers
- interni postopek / internal procedure: ML10N31, ML10N55
145. (0,1 do/ to 2) bar 0,45 mbar EURAMET / cg-17 / v.02 / 2011, DKD-R 6-1 Medij: plin Medium: gas
Ovrednotenje komor: parni sterilizatorji, avtoklavi, tlačne komore Evaluation of chambers: Steam sterilizers, Autoclaves, Pressure chambers
- interni postopek / internal procedure: ML10N12
146. (0,1 do/ to 5) bar 0,15 bar Medij: plin, tekočina Medium: gas, fluid
Moment sile
Torque
Momentni ključi Torque Wrenches
- interni postopek / internal procedure: ML10N70
147. (0,1 do/ to 1) Nm 0,9 % ISO 6789:2003
148. (1 do/ to 2) Nm 0,7 %
149. (2 do/ to 6) Nm 0,6 %
150. (6 do/ to 10) Nm 0,5 %
151. (10 do/ to 20) Nm 0,9 %
152. (20 do/ to 100) Nm 0,6 %
153. (100 do/ to 1000) Nm 0,7 %
154. (1000 do/ to 2000) Nm 0,5 %
155. (2000 do/ to 3000) Nm 0,3 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 13 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Pospešek
Acceleration
Merilniki pojemkov in pospeškov Acceleration and Deceleration measuring instruments
- interni postopek / internal procedure: ML10N45
156. do/ to 9,806 ms-2 0,03 ms-2
Trdota
Hardness
Merilniki trdote Hardness testers
- interni postopek / internal procedure: ML10N117
157. Shore Shore
(10 do/ to 100) Shore 1,5 Shore ISO 18898:2012 ISO 7619-1:2010
158. IRHD (10 do/ to 100) IRHD 1,5 IRHD ISO 18898:2012 ISO 7619-1:2010
Merilniki trdote po Brinellu Brinell hardness testers
- interni postopek / internal procedure: ML10N115
159. (60 do/ to 500) HB
2,0 %
ISO 6506-2:2014 ASTM E10-12 posredna in neposredna metoda / indirect and direct method
Merilniki trdote po Vickersu Vickers hardness testers
- interni postopek / internal procedure: ML10N118
160. (50 do/ to 800) HV
2,0 %
ISO 6507-2:2005 ASTM 384-11 posredna in neposredna metoda / indirect and direct method
Merilniki trdote po Rockwellu Rockwell hardness testers
- interni postopek / internal procedure: ML10N116
161. (20 do/ to 85) HRA 2,0 HRA ISO 6508-2:2014 ASTM E18-14 posredna in neposredna metoda / indirect and direct method
162. (20 do/ to 100) HRB 2,0 HRB
163. (20 do/ to 65) HRC 2,0 HRC
164. (40 do/ to 80) HRD 2,0 HRD
165. (70 do/ to 100) HRE 2,0 HRE
166. (70 do/ to 100) HRF 2,0 HRF
167. (20 do/ to 85) HRG 2,0 HRG
168. (70 do/ to 100) HRH 2,0 HRH
169. (35 do/ to 100) HRK 2,0 HRK
170. (40 do/ to 90) HRN 2,0 HRN
171. (30 do/ to 80) HRT 2,0 HRT
FLUIDNE VELIČINE
FLUID QUANTITIES
Hitrost plinov in tekočin
Gas and Fluid flow rate
Merilniki hitrosti zraka Anemometers
- interni postopek / internal procedure: ML10N141
172. (0,3 do/ to 1) m/s 0,10 m/s
173. (1 do/ to 2) m/s 0,11 m/s
174. (2 do/ to 5) m/s 0,16 m/s
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 14 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
175. (5 do/ to 10) m/s 0,25 m/s
176. (10 do/ to 15) m/s 0,34 m/s
177. (15 do/ to 20) m/s 0,44 m/s
178. (20 do/ to 25) m/s 0,53 m/s
179. (25 do/ to 30) m/s 0,62 m/s
180. (30 do/ to 35) m/s 0,71 m/s
181. (35 do/ to 40) m/s 0,80 m/s
Volumen tekočin
Volume of Liquids
Pipete (enokanalne), dispenzorji in batne birete (razdeljevalci) Pipettes (single-channel), Dispensers and Piston Burettes (Titrators)
- interni postopek / internal procedure: ML10N03
182. do/ to 0,5 µl 0,007 µl ISO 8655-6:2002 / Cor 1 :2008
183. (0,5 do/ to 2,5) µl 0,010 µl
184. (2,5 do/ to 10) µl 0,013 µl
185. (10 do/ to 25) µl 0,014 µl
186. (25 do/ to 50) µl 0,018 µl
187. (50 do/ to 100) µl 0,06 µl
188. (100 do/ to 250) µl 0,08 µl
189. (250 do/ to 500) µl 0,15 µl
190. (500 do/ to 1000) µl 0,32 µl
191. (1 do/ to 2,5) ml 0,65 µl
192. (2,5 do/ to 5) ml 1,45 µl
193. (5 do/ to 10) ml 3,10 µl
194. (10 do/ to 25) ml 6,20 µl
195. (25 do/ to 50) ml 15 µl
196. (50 do/ to 100) ml 43 µl
197. (100 do/ to 200) ml 69 µl
Pipete (večkanalne) Pipettes (multi-channel)
- interni postopek / internal procedure: ML10N03
198. do/ to 0,5 µl 0,007 µl ISO 8655-6:2002 / Cor 1 :2008
199. (0,5 do/ to 2,5) µl 0,011 µl
200. (2,5 do/ to 10) µl 0,014 µl
201. (10 do/ to 25) µl 0,016 µl
202. (25 do/ to 50) µl 0,020 µl
203. (50 do/ to 100) µl 0,035 µl
204. (100 do/ to 250) µl 0,18 µl
205. (250 do/ to 500) µl 0,43 µl
206. (500 do/ to 1000) µl 0,84 µl
207. (1000 do/ to 2000) µl 1,68 µl
Steklene merilne in polnilne pipete, birete in steklenice za merjenje gostote Glass graduated and Bulb pipettes, Flash, Burettes and Density bottles – Pycnometers
- interni postopek / internal procedure: ML10N10
208. do/ to 2 ml 1 µl Merilna negotovost skladno s
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 15 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
209. (2 do/ to 5) ml 2 µl EURAMET / cg-19 / v2.1 / 2012 Uncertainty in accordance with EURAMET / cg-19 / v2.1 / 2012 210. (5 do/ to 10) ml 4 µl
211. (10 do/ to 20) ml 8 µl
212. (20 do/ to 25) ml 10 µl
213. (25 do/ to 50) ml 20 µl
214. (50 do/ to 200) ml 40 µl
215. (200 do/ to 500) ml 80 µl
216. (500 do/ to 1000) ml 110 µl
217. (1000 do/ to 2000) ml 230 µl
Merilni valji in steklenice Graduated Cylinders and Bottles
- interni postopek / internal procedure: ML10N10
218. do/to 20 ml 0,016 ml Merilna negotovost skladno s EURAMET / cg-19 / v2.1 / 2012 Uncertainty in accordance with EURAMET / cg-19 / v2.1 / 2012
219. (20 do/ to 50) ml 0,02 ml
220. (50 do/ to 100) ml 0,03 ml
221. (100 do/ to 200) ml 0,08 ml
222. (200 do/ to 500) ml 0,3 ml
223. (500 do/ to 1000) ml 0,4 ml
224. (1000 do/ to 2000) ml 0,6 ml
Volumske posode Volume Vessels
- interni postopek / internal procedure: ML10N10
225. do/ to 2 l 2,2 ml
226. (2 do/ to 5) l 4,4 ml
227. (5 do/ to 10) l 6,8 ml
228. (10 do/ to 20) l 12,5 ml
229. (20 do/ to 25) l 15,0 ml
230. (25 do/ to 50) l 31 ml
231. (50 do/ to 100) l 75 ml
232. (100 do/ to 200) l 131 ml
233. (200 do/ to 300) l 187 ml
234. (300 do/ to 350) l 215 ml
Volumen teles Body volume
- interni postopek / internal procedure: ML10N122
235. do/ to 200 cm3 0,0005 cm3
Porozimetri z metodo pritiska po EN 12350-7 ali ASTM C231/C231M-10 Porosimeters with pressure method according to EN 12350-7 or ASTM C231/C231M-10
- interni postopek / internal procedure: ML10N170
236. (1 do/ to 10) l 0,1 % EN 12350-7:2009, Annex D ali / or: ASTM C231/C231M-10, A1.9
Gostota
Density
Gostotni hidrometri Areometers
- interni postopek / internal procedure: ML10N172
237. (600 do/ to 2000) kg/m3 0,0005 g/cm3
ISO 649-2:1981 ASTM E-126:2005
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 16 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
OPTIČNE VELIČINE
OPTICAL QUANTITIES
Lastnosti optičnih sistemov
Optical system properties
Merilniki prepustnosti svetlobe Tintmeters
- interni postopek / internal procedure: ML10N13
238. (0 do / to 100) % 0,5 % Kalibracija z referenčnimi filtri Calibration with reference filters
Regloskopi Regloscopes
- interni postopek / internal procedure: ML10N4
239. (0 do/ to 5) % 0,07 %
Merilniki sijaja Glossmeters
- interni postopek / internal procedure: ML10N165
240. (0 do/ to 100) GU 1,1 GU
TEMPERATURA, VLAGA IN TERMOFIZIKALNE LASTNOSTI
TEMPERATURE, HUMIDITY AND THERMO-PHYSICAL PROPERTIES
Temperatura
Temperature
Uporovni termometri Resistance Thermometers
- interni postopek / internal procedure: ML10N161
241. (- 90 do/ to - 70) °C 0,12 °C
242. (- 70 do/ to - 40) °C 0,05 °C
243. (- 40 do/ to 0) °C 0,06 °C
244. (0 do/ to 50) °C 0,04 °C
245. (50 do/ to 150) °C 0,16 °C
246. (150 do/ to 250) °C 0,17 °C
247. (250 do/ to 280) °C 0,18 °C
248. (280 do/ to 400) °C 0,29 °C
Termočleni Thermocouples
- interni postopek / internal procedure: ML10N159
249. (- 80 do/ to - 40) °C 0,12 °C
250. (- 40 do/ to 0) °C 0,24 °C
251. (0 do/ to 100) °C 0,20 °C
252. (100 do/ to 150) °C 0,23 °C
253. (150 do/ to 200) °C 0,27 °C
254. (200 do/ to 250) °C 0,32 °C
255. (250 do/ to 280) °C 0,36 °C
256. (280 do/ to 400) °C 0,54 °C
257. (400 do/ to 600) °C 2,6 °C
258. (600 do/ to 800) °C 2,7 °C
259. (800 do/ to 1100) °C 3,8 °C
Tekočinski termometri Liquid-in-glass Thermometers
- interni postopek / internal procedure: ML10N26
260. (- 40 do/ to 0) °C 0,05 °C
261. (0 do/ to 150) °C 0,04 °C
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 17 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
262. (150 do/ to 250) °C 0,05 °C
263. (250 do/ to 280) °C 0,06 °C
Termometri s prikazovalnikom Thermometers with indicators
- interni postopek / internal procedure: ML10N26
264. (- 90 do/ to - 70) °C 0,12 °C
265. (- 70 do/ to 0) °C 0,05 °C
266. (0 do/ to 100) °C 0,03 °C
267. (100 do/ to 150) °C 0,04 °C
268. (150 do/ to 250) °C 0,05 °C
269. (250 do/ to 280) °C 0,06 °C
270. (280 do/ to 400) °C 0,24 °C
271. (400 do/ to 800) °C 2,7 °C
272. (800 do/ to 1100) °C 3,7 °C
Indikatorji uporovnih termometrov Resistance Thermometers Indicators
- interni postopek / internal procedure: ML10N163
273. (- 200 do/ to - 100) °C 0,024 °C EURAMET / cg-11 / v2.0 / 2011 S simulacijo By simulation
274. (- 100 do/ to 0) °C 0,029 °C
275. (0 do/ to 100) °C 0,054 °C
276. (100 do/ to 200) °C 0,32 °C
277. (200 do/ to 300) °C 0,33 °C
278. (300 do/ to 400) °C 0,34 °C
279. (400 do/ to 600) °C 0,36 °C
280. (600 do/ to 850) °C 0,40 °C
Indikatorji termočlenov Thermocouples Indicators
- interni postopek / internal procedure: ML10N16
281. (- 260 do/ to - 100) °C 1,65 °C EURAMET / cg-11 / v2.0 / 2011 S simulacijo By simulation
282. (- 100 do/ to 0) °C 0,33 °C
283. (0 do/ to 100) °C 0,24 °C
284. (100 do/ to 400) °C 0,17 °C
285. (400 do/ to 1200) °C 0,14 °C
286. (1200 do/ to 1760) °C 0,15 °C
Simulatorji uporovnih termometrov Resistance Thermometers Simulators
- interni postopek / internal procedure: ML10N163
287. (- 200 do/ to 100) °C 0,03 °C EURAMET / cg-11 / v2.0 / 2011 S simulacijo By simulation
288. (100 do/ to 200) °C 0,32 °C
289. (200 do/ to 300) °C 0,33 °C
290. (300 do/ to 400) °C 0,34 °C
291. (400 do/ to 600) °°C 0,37 °C
292. (600 do/ to 850) °C 0,40 °C
Simulatorji termočlenov Thermocouples Simulators
- interni postopek / internal procedure: ML10N163
293. (- 260 do/ to - 100) °C 1,20 °C EURAMET / cg-11 / v2.0 / 2011
294. (- 100 do/ to 0) °C 0,25 °C
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 18 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
295. (0 do/ to 100) °C 0,18 °C S simulacijo By simulation
296. (100 do/ to 400) °C 0,12 °C
297. (400 do/ to 1200) °C 0,10 °C
298. (1200 do/ to 1760) °C 0,11 °C
Sevalni termometri Radiation Thermometers
- interni postopek / internal procedure: ML10N67
299. (- 40 do/ to 280) °C 2,0 °C Primerjava s črnim telesom By comparison with black body
300. (35 do/ to 500) °C 3,4 °C Primerjava z referenčnim sevalnim termometrom / By comparison with reference radiation thermometer
Ušesni termometri Ear Thermometers
- interni postopek / internal procedure: ML10N67
301. (35 do/ to 42) °C 0,15 °C Primerjava s črnim telesom By comparison with black body Črno telo / black body: EN 12470-5:2003
Vlažnost
Humidity
Merilniki relativne vlažnosti Relative Humidity sensors
- interni postopek / internal procedure: ML10N147
302. pri / at (20 do/ to 30) °C 11,3 % 0,9 % Primerjalna metoda z uporabo kalibriranimi referenčnih soli By comparison method using calibrated reference salts
303. 32,9 % 1,0 %
304. 74,8 % 1,8 %
305. 96,8 % 1,6 %
Merilniki relativne vlažnosti Relative Humidity sensors
- interni postopek / internal procedure: ML10N147
306. pri / at (20 do/ to 30) °C 1,9 % 1,5 % Primerjalna metoda z uporabo referenčnega higrometra v soleh By comparison method using reference hygrometer in salts
307. 11,3 % 1,3 %
308. 32,9 % 1,1 %
309. 53,1 % 1,5 %
310. 74,8 % 1,5 %
311. 83,9 % 1,8 %
312. 96,8 % 2,2 %
Merilniki relativne vlažnosti Relative Humidity sensors
- interni postopek / internal procedure: ML10N62
313. pri / at (10 do/ to 20) °C (66 do/ to 95) % 2,5 % Primerjalna metoda z uporabo referenčnega higrometra v komori By comparison method using reference hygrometer in chamber
314. pri / at (20 do/ to 22) °C (34 do/ to 95) % 2,5 %
315. pri / at (22 do/ to 30) °C (30 do/ to 95) % 2,5 %
316. pri / at (30 do/ to 40) °C (19 do/ to 95) % 2,5 %
317. pri / at (40 do/ to 50) °C (11 do/ to 95) % 2,5 %
318. pri / at (50 do/ to 60) °C (10 do/ to 95) % 2,5 %
Ovrednotenje klimatsko reguliranih komor
Evaluation of climatic controlled chambers
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 19 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Klimatske komore: stabilizatorji, sušilniki, vakuumski sušilniki, termostatirane komore in prostori, hladilniki, zamrzovalne skrinje, kopeli Climatic chamber: Stabilizer, Dryers, Vacuum dryers, Thermostat Chambers and Rooms, Refrigerators, Freezers, Baths
- interni postopek / internal procedure: ML10N12
319. (- 80 do/ to - 40) °C 0,61 °C EURAMET / cg-20 / v4.0 / 2015
320. (- 40 do/ to 0) °C 0,20 °C
321. (0 do/ to 20) °C 0,19 °C
322. (20 do/ to 150) °C 0,20 °C
323. (150 do/ to 180) °C 0,48 °C
324. (180 do/ to 280) °C 2,03 °C
325. pri / at (10 do/ to 20) °C (66 do/ to 95) % 3,0 % EURAMET / cg-20 / v4.0 / 2015
326. pri / at (20 do/ to 22) °C (34 do/ to 95) % 3,0 %
327. pri / at (22 do/ to 30) °C (30 do/ to 95) % 3,0 %
328. pri / at (30 do/ to 40) °C (19 do/ to 95) % 3,0 %
329. pri / at (40 do/ to 50) °C (11 do/ to 95) % 3,0 %
330. pri / at (50 do/ to 60) °C (10 do/ to 95) % 3,0 %
Parni sterilizatorji, avtoklavi Steam sterilizers, Autoclaves
- interni postopek / internal procedure: ML10N12
331. (- 40 do/ to 140) °C 0,32 °C
Temperaturne kalibracijske kopeli Temperature Calibration Baths
- interni postopek / internal procedure: ML10N53
332. (- 70 do/ to 40) °C 0,048 °C
333. (- 40 do/ to 0) °C 0,042 °C
334. (0 do/ to 20) °C 0,036 °C
335. (20 do/ to 100) °C 0,028 °C
336. (100 do/ to 150) °C 0,033 °C
337. (150 do/ to 200) °C 0,036 °C
338. (200 do/ to 250) °C 0,040 °C
339. (250 do/ to 300) °C 0,042 °C
Temperaturni suhi kalibratorji Thermoblock calibrators
- interni postopek / internal procedure: ML10N151
340. (- 90 do/ to 400) °C 0,09 °C EURAMET / cg-13 / v3.0 / 2015
Peči Furnaces
- interni postopek / internal procedure: ML10N149
341. (50 do/ to 1100) °C 2,2 °C
KEMIJSKA ANALIZA, REFERENČNI MATERIALI
CHEMICAL ANALYSIS, REFERENCE MATERIALS
Instrumenti za analizo / monitoring
Analytical instruments / monitors
Merilniki izpušnih plinov Gas exhaust analysers
- interni postopek / internal procedure: ML10N128
342. CO (0 do/ to 5) % 1,0 % Kalibracija z referenčnimi mešanicami plinov
343. CO2 (0 do/ to 16) % 1,0 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 20 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
344. O2 (0 do/ to 21) % 1,0 % Calibration with reference gas mixtures
345. C3H8 (0 do/ to 2000) ∙ 10-6 1,0 %
Merilniki izpušnih plinov na kompresijski vžig Diesel exhaust analysers
- interni postopek / internal procedure: ML10N130
346. (0 do/ to 9,99) m-1 0,5 % Kalibracija z referenčnimi stekli Calibration with reference glasses 347. (0 do/ to 100) % 0,5 %
pH merilniki z notranjo impedanco: 100Ω/1000MΩ pH measuring equipment with inner impedance of: 100Ω/1000MΩ
- interni postopek / internal procedure: ML10N83
348. (0 do/ to 12,45) pH 0,009 pH Kalibracija s simulacijo, brez sonde Calibration without probe with simulation 349. (-1999 do/ to 1999) mV 0,30 mV
Merilniki prevodnosti tekočin Conductivity measuring equipment
- interni postopek / internal procedure: ML10N83
350. (0,04 do/ to 100) µS/cm 0,2%
Kalibracija s simulacijo, brez sonde Calibration without probe with simulation 351. (0,1 do/ to 800) mS/cm 0,1%
Merilniki slanosti Salinity meters
- interni postopek / internal procedure: ML10N142
352. (0,00005 do/ to 0,0002) kg/kg 1,3 %
353. (0,0002 do/ to 0,035) kg/kg 0,8 %
Tabela / Table 2 – kalibracije na terenu / on-site calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
ČAS IN FREKVENCA
TIME AND FREQUENCY
Časovni interval
Time interval
ƒ = merjena vrednost frekvence / measured value of frequency
Merilniki časa
Timers
- interni postopek / internal procedure:
ML10N111
354. Čas
Time
24 h 0,1 s
Tahometri
Tachometers
Naprave za kontrolo hitrosti Speedometers
- interni postopek / internal procedure: ML10N43
355. (10 do/ to 90) km/h 0,1 km/h
356. (90 do/ to 200) km/h 0,2 km/h
357. (200 do/ to 250) km/h 0,3 km/h
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 21 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Oprema za kontrolo tahografov Equipment for tachographs inspection
- interni postopek / internal procedure: ML10N113
358. Hitrost Speed
(13 do/ to 1200) Hz (20 do/ to 180) km/h
0,04 Hz + 0,0003·ƒ
359. Prevožena pot Travelled distance
(1000 do/ to 10000) m 0,2 %
360. Časovni interval
Time interval
24 h
0,1 s / 24 h
Merilniki obratov Tachometers
- interni postopek / internal procedure: ML10N138
361. do/ to 60 min-1 0,01 min-1
362. (60 do/ to 300) min-1 0,05 min-1
363. (300 do/ to 600) min-1 0,07 min-1
364. (600 do/ to 5000) min-1 0,5 min-1
365. (5000 do/ to 10000) min-1 0,7 min-1
366. (10000 do/ to 30000) min-1 5 min-1
367. (30000 do/ to 60000) min-1 6 min-1
368. (60000 do/ to 99999) min-1 7 min-1
DIMENZIONALNE VELIČINE
DIMENSIONAL QUANTITIES
Dolžina
Length
Merila dolžine
Length gauges L – merjena dolžina / measured length
Merilne urice Dial gauges
- interni postopek / internal procedure: ML10N89
369. do/ to 100 mm 0,4 μm + 2·10-5·L Kalibracija samo z obremenjevanjem Calibration with increasing only
Merilniki globine pnevmatik Tire depth gauges
- interni postopek / internal procedure: ML10N89
370. do/ to 100 mm 0,03 mm
Elektronska tipala Electronic probes
- interni postopek / internal procedure: ML10N89
371. do/ to 100 mm 0,4 μm + 2·10-5·L Kalibracija brez histereze Calibration without hysteresis
Instrumenti za merjenje dolžine
Length measuring instruments
Dvotočkovna vijačna merila (zunanja in notranja) Two point micrometers (external and internal)
- interni postopek / internal procedure: ML10N74
372. do/ to 2000 mm 1,0 μm + 9·10-6·L ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Pomična merila Vernier calliper gauges
- interni postopek / internal procedure: ML10N72
373. do/ to 3000 mm 7,5 μm + 5·10-5·L ISO 13385:2011 ISO 13225:2012 VDI/VDE/DGQ 2618:2007
Ultrazvočni merilniki debeline Ultrasonic thickness meters
- interni postopek / internal procedure: ML10N120
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 22 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
374. do/ to 50 mm 15 µm + 4·10-3·L
Magnetni merilniki debeline Magnetic thickness gauges
- interni postopek / internal procedure: ML10N120
375. do/ to 12,5 mm 1,7 µm
Merilniki izteka koles Wheel alignment testers
- interni postopek / internal procedure: ML10N65
376. do/ to 50 mm/m (m/km) 0,4 mm/m (m/km)
Hrapavost
Roughness
Instrumenti za merjenje hrapavosti Instruments for Roughness measurement
- interni postopek / internal procedure: ML10N145
377. (0,065 do/ to 1,63) μm 0,05 µm + 7·10-2 Ra
Koordinatni merilni stroji
Co-ordinate measuring machines
1D naprave 1D machines
- interni postopek / internal procedure: ML10N109
378. do/ to 1000 mm 0,2 µm + 4·10-6·L
2D naprave 2D machines
- interni postopek / internal procedure: ML10N109
379. do/ to (200 x 300) mm 1,5 µm + 3·10-6·L
3D naprave 3D machines
- interni postopek / internal procedure: ML10N109
380. do/ to (1500 x 1500) mm 1,0 µm + 2,5·10-6·L
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Sila
Force
Pretvorniki sile Force transducers
- interni postopek / internal procedure: ML10N47
381. (1 do/ to 10) N 0,011 N
382. (10 do/ to 400) N 0,11 N
383. (400 do/ to 600) N 0,12 N
384. (600 do/ to 1000) N 0,13 N
385. (1000 do/ to 2000) N 1,1 N
386. (2000 do/ to 2500) N 1,2 N
387. (2500 do/ to 5000) N 3,5 N
Merilni stroji za merjenje sile Force measuring machines
- interni postopek / internal procedure: ML10N105
388. nateg / tension (0,2 do / to 200) kN 0,25 % ISO 7500-1:2015
389. tlak / compression (0,2 do / to 3000) kN 0,25 %
Merilni stroji za merjenje sile - merjenje položaja prečke Force measuring machines - Position measurement of the crosshead
- interni postopek / internal procedure: ML10N105
390. do/ to 1000 mm 0,05 mm + 4,5·10-4 · L
Merilni stroji za merjenje sile – stiskalnice za beton Force measuring machines – concrete testing machines
- interni postopek / internal procedure: ML10N103
391. (0,2 do / to 3000) kN 0,3 % EN 12390-4:2000
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 23 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Naprave z valji za preverjanje zaviralne sile Roll brake testers
- interni postopek / internal procedure: ML10N126
392. (0,1 do/ to 0,5) kN 1,6 % Steza za osebna vozila in kolesa z motorjem Track for cars and mopeds 393. (0,5 do/ to 1) kN 1,4 %
394. (1 do/ to 2) kN 1,2 %
395. (2 do/ to 3) kN 1,0 %
396. (3 do/ to 6) kN 0,9 %
397. (0,1 do/ to 10) kN 1,8 % Steza za tovorna in priklopna vozila Track for trucks
398. (10 do/ to 20) kN 0,8 %
399. (20 do/ to 30) kN 0,6 %
Mehanska energija
Mechanical energy
Merilniki udarne žilavosti Pendulum impact machines
- interni postopek / internal procedure: ML10N168
400. (0,2 J do/ to 50) J ISO 13802:2008
401. Čas / Time 0,1 s
402. Kot / Angle 0,2 °
403. Sila /Force 0,2 % (ne/not < 0,02 N)
404. Dolžina / Length 0,2 % (ne/not < 0,02 mm)
Masa (konvencionalna)
Conventional Mass
Etalonske uteži Standard Weights
- interni postopek / internal procedure: ML10N02, ki temelji na / which is based on OIML R 111-1 (2004)
405. 100 mg 0,15 mg
406. 200 mg 0,20 mg
407. 500 mg 0,25 mg
408. 1 g 0,3 mg
409. 2 g 0,4 mg
410. 5 g 0,5 mg
411. 10 g 0,6 mg
412. 20 g 0,8 mg
413. 50 g 1,0 mg
414. 100 g 1,5 mg
415. 200 g 3,0 mg
416. 500 g 7,5 mg
417. 1 kg 15 mg
418. 2 kg 30 mg
419. 5 kg 75 mg
420. 10 kg 150 mg
421. 20 kg 300 mg
422. 500 kg 15 g
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 24 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Predmeti ostalih poljubnih mas
Objects of any other Mass
- interni postopek / internal procedure: ML10N02
423. do/ to 1 g 1 mg
424. (1 do/ to 5) g 2 mg
425. (5 do/ to 20) g 3 mg
426. (20 do/ to 50) g 5 mg
427. (50 do/ to 100) g 6 mg
428. (100 do/ to 205) g 8 mg
429. (205 do/ to 500) g 15 mg
430. (500 do/ to 1000) g 25 mg
431. (1 do/ to 2,1) kg 50 mg
432. (2,1 do/ to 5) kg 250 mg
433. (5 do/ to 10) kg 300 mg
434. (10 do/ to 20) kg 450 mg
435. (20 do/ to 32) kg 650 mg
436. (32 do/ to 400) kg 28 g
Tehtnice
Weighing instruments
m = masa / mass
Neavtomatske tehtnice
Non-automatic weighing instruments
- interni postopek / internal procedure: ML10N01, ki temelji na / which is based on EURAMET / cg-18 / v.04 / 2015
437. do/ to 0,005 g 0,004 mg
438. (0,005 do/ to 0,02) g 0,005 mg
439. (0,02 do/ to 0,05) g 0,006 mg
440. (0,02 do/ to 0,1) g 0,008 mg
441. (0,1 do/ to 0,2) g 0,009 mg
442. (0,2 do/ to 0,5) g 0,012 mg
443. (0,5 do/ to 1) g 0,015 mg
444. (1 do/ to 2) g 0,019 mg
445. (2 do/ to 5) g 0,024 mg
446. (5 do/ to 10) g 0,030 mg
447. (10 do/ to 20) g 0,039 mg
448. (20 do/ to 50) g 0,051 mg
449. (50 do/ to 100) g 0,088 mg
450. (100 do/ to 200) g 0,16 mg
451. (0,2 do/ to 25) kg m·(8,0·10-7)
452. (25 do/ to 100) kg m·(2,5·10-6)
453. (100 do/ to 600) kg m·(3,0·10-6)
454. (600 do/ to 6000) kg m·(1,5·10-4)
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 25 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
455. (6 do/ to 37,5) t m·(2,5·10-4)
456. (37,5 do/ to 60) t m·(3,5·10-4)
457. (60 do/ to 75) t m·(4,0·10-4)
458. (75 do/ to 100) t m·(5,0·10-4)
Tlak
Pressure
Podtlak: mehanski in elektromehanski manometri Negative pressure gauge: Mechanical and electromechanical manometers
- interni postopek / internal procedure: ML10N31, ML10N55
459. (- 0,95 do/ to 0) bar 0,34 mbar EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij: plin, tekočina Medium: gas, fluid
Nadtlak: merilniki krvnega tlaka Positive pressure gauge: Sphygmomanometers
- interni postopek / internal procedure: ML10N31, ML10N55
460. (0 do/ to 300) mmHg 0,064 mmHg EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij:plin Medium: gas
461. (0 do/ to 40) kPa 8,5 Pa
Nadtlak: mehanski in elektromehanski manometri, merilniki tlaka v pnevmatikah Positive pressure gauge: Mechanical, Electromechanical and, Tyre pressure manometers
- interni postopek / internal procedure: ML10N31, ML10N55
462. (0 do/ to 2500) Pa 1,4 Pa + 1,9.10-3p EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij: plin, tekočina Medium: gas, fluid
463. 2500 Pa do/ to 17,5 bar 2 mbar
464. (17,5 do/ to 35) bar 2,5 mbar
465. (35 do/ to 160) bar 0,05 bar
466. (160 do/ to 1000) bar 0,32 bar
Absolutni tlak: mehanski, elektromehanski in tekočinski barometri Atmospheric pressure: Mechanical, Electromechanical and Liquid barometers
- interni postopek / internal procedure: ML10N31, ML10N55
467. (0,1 do/ to 2) bar 0,45 mbar EURAMET / cg-17 / v2.0 / 2011, DKD-R 6-1 Medij: plin Medium: gas
Ovrednotenje komor: parni sterilizatorji, avtoklavi, tlačne komore Evaluation of chambers: Steam sterilizers, Autoclaves, Pressure chambers
- interni postopek / internal procedure: ML10N12
468. (0,1 do/ to 5) bar 0,15 bar Medij: plin, tekočina Medium: gas, fluid
Moment sile
Torque
Momentni ključi Torque Wrenches
- interni postopek / internal procedure: ML10N70
469. (0,1 do/ to 0,2) Nm 1,2 % ISO 6789:2003
470. (0,2 do/ to 1) Nm 1,0 %
471. (1 do/ to 2) Nm 0,9 %
472. (2 do/ to 10) Nm 0,8 %
473. (10 do/ to 20) Nm 1,1 %
474. (20 do/ to 1000) Nm 0,9 %
475. (1000 do/ to 2000) Nm 0,8 %
476. (2000 do/ to 3000) Nm 0,7 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 26 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Pospešek
Acceleration
Merilniki pojemkov in pospeškov Acceleration and Deceleration measuring instruments
- interni postopek / internal procedure: ML10N45
477. do/ to 9,806 ms-2 0,03 ms-2
Trdota
Hardness
Merilniki trdote Hardness testers
- interni postopek / internal procedure: ML10N117
478. Shore Shore
(10 do/ to 100) Shore 1,5 Shore ISO 18898:2012 ISO 7619-1:2010
479. IRHD (10 do/ to 100) IRHD 1,5 IRHD ISO 18898:2012 ISO 7619-1:2010
Merilniki trdote po Brinellu Brinell hardness testers
- interni postopek / internal procedure: ML10N115
480. (60 do/ to 500) HB
2,0 %
ISO 6506-2:2014 ASTM E10-12 posredna in neposredna metoda / indirect and direct method
Merilniki trdote po Vickersu Vickers hardness testers
- interni postopek / internal procedure: ML10N118
481. (50 do/ to 800) HV
2,0 %
ISO 6507-2:2005 ASTM 384-11 posredna in neposredna metoda / indirect and direct method
Merilniki trdote po Rockwellu Rockwell hardness testers
- interni postopek / internal procedure: ML10N116
482. (20 do/ to 85) HRA 2,0 HRA ISO 6508-2:2014 ASTM E18-14 posredna in neposredna metoda / indirect and direct method
483. (20 do/ to 100) HRB 2,0 HRB
484. (20 do/ to 65) HRC 2,0 HRC
485. (40 do/ to 80) HRD 2,0 HRD
486. (70 do/ to 100) HRE 2,0 HRE
487. (70 do/ to 100) HRF 2,0 HRF
488. (20 do/ to 85) HRG 2,0 HRG
489. (70 do/ to 100) HRH 2,0 HRH
490. (35 do/ to 100) HRK 2,0 HRK
491. (40 do/ to 90) HRN 2,0 HRN
492. (30 do/ to 80) HRT 2,0 HRT
Masno uravnoteženje
Mass balance
Stroji za uravnoteženje pnevmatik Wheel balancing machine
- interni postopek / internal procedure: ML10N137
493. do/ to 100 g·mm 4,5 g·mm
FLUIDNE VELIČINE
FLUID QUANTITIES
Volumen tekočin
Volume of Liquids
Sistemi za avtomatsko pipetiranje Automated liquid handling systems (ALHS)
- interni postopek / internal procedure: ML10N200
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 27 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
494. do/ to 0,5 µl 0,015 µl IWA 15:2015 (točka / point B.2), v povezavi z / in relation with ISO 8655-6:2002 / Cor 1 :2008 495. (0,5 do/ to 2,5) µl 0,017 µl
496. (2,5 do/ to 10) µl 0,019 µl
497. (10 do/ to 25) µl 0,020 µl
498. (25 do/ to 50) µl 0,026 µl
499. (50 do/ to 100) µl 0,045 µl
500. (100 do/ to 250) µl 0,18 µl
501. (250 do/ to 500) µl 0,44 µl
502. (500 do/ to 1000) µl 0,88 µl
503. (1000 do/ to 2000) µl 1,75 µl
Batne birete (razdeljevalci) Piston Burettes (Titrators)
- interni postopek / internal procedure: ML10N03
504. do/ to 250 µl 0,46 µl ISO 8655-6:2002 / Cor 1 :2008
505. (250 do/ to 500) µl 0,48 µl
506. (500 do/ to 1000) µl 0,53 µl
507. (1000 do/ to 2500) µl 0,7 µl
508. (2500 do/ to 5000) µl 1,5 µl
509. (5000 do/ to 10000) µl 2,7 µl
510. (10 do/ to 25) ml 5,4 µl
511. (25 do/ to 50) ml 13,3 µl
512. (50 do/ to 100) ml 53,1 µl
Volumen pretok kapljevin
Volume of flowing Liquids
Volumetrični dozirni sistemi – pretečeni volumen Volumetric dosing systems – volume of flow
- interni postopek / internal procedure: ML10N78
513. do/ to 1 ml 0,006 ml
514. (1 do/ to 2) ml 0,007 ml
515. (2 do/ to 5) ml 0,010 ml
516. (5 do/ to 10) ml 0,016 ml
517. (10 do/ to 20) ml 0,03 ml
518. (20 do/ to 50) ml 0,08 ml
519. (50 do/ to 100) ml 0,15 ml
520. (100 do/ to 200) ml 0,6 ml
521. (200 do/ to 500) ml 1,0 ml
522. (500 do/ to 1000) ml 1,6 ml
523. (1000 do/ to 5000) ml 3,0 ml
524. (5 do/ to 10) l 0,05 l
525. (10 do/ to 20) l 0,06 l
526. (20 do/ to 30) l 0,08 l
527. (30 do/ to 100) l 0,5 l
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 28 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
528. (100 do/ to 200) l 0,6 l
529. (200 do/ to 300) l 0,7 l
530. (300 do/ to 400) l 0,8 l
531. (400 do/ to 500) l 0,9 l
OPTIČNE VELIČINE
OPTICAL QUANTITIES
Lastnosti optičnih sistemov
Optical system properties
Merilniki prepustnosti svetlobe Tintmeters
- interni postopek / internal procedure: ML10N130
532. (0 do / to 100) % 0,5 % Kalibracija z referenčnimi filtri Calibration with reference filters
Regloskopi Regloscopes
- interni postopek / internal procedure: ML10N41
533. (0 do/ to 5) % 0,07 %
Merilniki sijaja Glossmeters
- interni postopek / internal procedure: ML10N165
534. (0 do/ to 100) GU 1,1 GU
TEMPERATURA, VLAGA IN TERMOFIZIKALNE LASTNOSTI
TEMPERATURE, HUMIDITY AND THERMO-PHYSICAL PROPERTIES
Temperatura
Temperature
Uporovni termometri Resistance Thermometers
- interni postopek / internal procedure: ML10N161
535. (- 90 do/ to - 70) °C 0,12 °C
536. (- 70 do/ to - 40) °C 0,05 °C
537. (- 40 do/ to 0) °C 0,06 °C
538. (0 do/ to 50) °C 0,04 °C
539. (50 do/ to 150) °C 0,16 °C
540. (150 do/ to 250) °C 0,17 °C
541. (250 do/ to 280) °C 0,18 °C
542. (280 do/ to 400) °C 0,29 °C
Termočleni Thermocouples
- interni postopek / internal procedure: ML10N159
543. (- 80 do/ to - 40) °C 0,12 °C
544. (- 40 do/ to 0) °C 0,24 °C
545. (0 do/ to 100) °C 0,20 °C
546. (100 do/ to 150) °C 0,23 °C
547. (150 do/ to 200) °C 0,27 °C
548. (200 do/ to 250) °C 0,32 °C
549. (250 do/ to 280) °C 0,36 °C
550. (280 do/ to 400) °C 0,54 °C
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 29 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
551. (400 do/ to 600) °C 2,6 °C
552. (600 do/ to 800) °C 2,7 °C
553. (800 do/ to 1100) °C 3,8 °C
Termometri s prikazovalnikom Thermometers with indicators
- interni postopek / internal procedure: ML10N26
554. (- 90 do/ to - 70) °C 0,12 °C
555. (- 70 do/ to 0) °C 0,04 °C
556. (0 do/ to 200) °C 0,09 °C
557. (200 do/ to 300) °C 0,18 °C
558. (300 do/ to 400) °C 0,24 °C
559. (400 do/ to 800) °C 2,7 °C
560. (800 do/ to 1100) °C 3,7 °C
Indikatorji uporovnih termometrov Resistance Thermometers Indicators
- interni postopek / internal procedure: ML10N163
561. (- 200 do/ to - 100) °C 0,024 °C EURAMET / cg-11 / v2.0 / 2011 S simulacijo By simulation
562. (- 100 do/ to 0) °C 0,029 °C
563. (0 do/ to 100) °C 0,054 °C
564. (100 do/ to 200) °C 0,32 °C
565. (200 do/ to 300) °C 0,33 °C
566. (300 do/ to 400) °C 0,34 °C
567. (400 do/ to 600) °C 0,36 °C
568. (600 do/ to 850) °C 0,40 °C
Indikatorji termočlenov Thermocouples Indicators
- interni postopek / internal procedure: ML10N163
569. (- 260 do/ to - 100) °C 1,65 °C EURAMET / cg-11 / v2.0 / 2011 S simulacijo By simulation
570. (- 100 do/ to 0) °C 0,33 °C
571. (0 do/ to 100) °C 0,24 °C
572. (100 do/ to 400) °C 0,17 °C
573. (400 do/ to 1200) °C 0,14 °C
574. (1200 do/ to 1760) °C 0,15 °C
Simulatorji uporovnih termometrov Resistance Thermometers Simulators
- interni postopek / internal procedure: ML10N163
575. (- 200 do/ to 100) °C 0,03 °C EURAMET / cg-11 / v2.0 / 2011 S simulacijo By simulation
576. (100 do/ to 200) °C 0,32 °C
577. (200 do/ to 300) °C 0,33 °C
578. (300 do/ to 400) °C 0,34 °C
579. (400 do/ to 600) °°C 0,37 °C
580. (600 do/ to 850) °C 0,40 °C
Simulatorji termočlenov Thermocouples Simulators
- interni postopek / internal procedure: ML10N163
581. (- 260 do/ to - 100) °C 1,20 °C EURAMET / cg-11 / v2.0 / 2011
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 30 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
582. (- 100 do/ to 0) °C 0,25 °C S simulacijo By simulation 583. (0 do/ to 100) °C 0,18 °C
584. (100 do/ to 400) °C 0,12 °C
585. (400 do/ to 1200) °C 0,10 °C
586. (1200 do/ to 1760) °C 0,11 °C
Sevalni termometri Radiation Thermometers
- interni postopek / internal procedure: ML10N67
587. (35 do/ to 500) °C 3,4 °C Primerjava z referenčnim sevalnim termometrom / By comparison with reference radiation thermometer
Vlažnost
Humidity
Merilniki relativne vlažnosti Relative humidity sensors
- interni postopek / internal procedure: ML10N147
588. pri / at (20 do/ to 30) °C 11,3 % 0,9 % Primerjalna metoda z uporabo kalibriranimi referenčnih soli By comparison method using calibrated reference salts
589. 32,9 % 1,0 %
590. 74,8 % 1,8 %
591. 96,8 % 1,6 %
Merilniki relativne vlažnosti Relative humidity sensors
- interni postopek / internal procedure: ML10N147
592. pri / at (20 do/ to 30) °C 1,9 % 1,5 % Primerjalna metoda z uporabo referenčnega higrometra v soleh By comparison method using reference hygrometer in salts
593. 11,3 % 1,3 %
594. 32,9 % 1,1 %
595. 53,1 % 1,5 %
596. 74,8 % 1,5 %
597. 83,9 % 1,8 %
598. 96,8 % 2,2 %
Ovrednotenje klimatsko reguliranih komor
Evaluation of climatic controlled chambers
Klimatske komore: stabilizatorji, sušilniki, vakuumski sušilniki, termostatirane komore in prostori, hladilniki, zamrzovalne skrinje, kopeli Climatic chamber: Stabilizer, Dryers, Vacuum dryers, Thermostat Chambers and Rooms, Refrigerators, Freezers, Baths
- interni postopek / internal procedure: ML10N12
599. (- 80 do/ to - 40) °C 0,61 °C EURAMET / cg-20 / v4.0 / 2015
600. (- 40 do/ to 0) °C 0,20 °C
601. (0 do/ to 20) °C 0,19 °C
602. (20 do/ to 150) °C 0,20 °C
603. (150 do/ to 180) °C 0,48 °C
604. (180 do/ to 280) °C 2,03 °C
605. pri / at (10 do/ to 20) °C (66 do/ to 95) % 3,0 % EURAMET / cg-20 / v4.0 / 2015
606. pri / at (20 do/ to 22) °C (34 do/ to 95) % 3,0 %
607. pri / at (22 do/ to 30) °C (30 do/ to 95) % 3,0 %
608. pri / at (30 do/ to 40) °C (19 do/ to 95) % 3,0 %
609. pri / at (40 do/ to 50) °C (11 do/ to 95) % 3,0 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 31 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
610. pri / at (50 do/ to 60) °C (10 do/ to 95) % 3,0 %
Parni sterilizatorji, avtoklavi Steam sterilizers, Autoclaves
- interni postopek / internal procedure: ML10N12
611. (- 40 do/ to 140) °C 0,32 °C
Temperaturne kalibracijske kopeli Temperature Calibration Baths
- interni postopek / internal procedure: ML10N53
612. (- 70 do/ to 40) °C 0,048 °C
613. (- 40 do/ to 0) °C 0,042 °C
614. (0 do/ to 20) °C 0,036 °C
615. (20 do/ to 100) °C 0,028 °C
616. (100 do/ to 150) °C 0,033 °C
617. (150 do/ to 200) °C 0,036 °C
618. (200 do/ to 250) °C 0,040 °C
619. (250 do/ to 300) °C 0,042 °C
Temperaturni suhi kalibratorji Thermoblock calibrators
- interni postopek / internal procedure: ML10N151
620. (- 90 do/ to 400) °C 0,09 °C EURAMET / cg-13 / v3.0 / 2015
Peči Furnaces
- interni postopek / internal procedure: ML10N149
621. (50 do/ to 1100) °C 2,2 °C
KEMIJSKA ANALIZA, REFERENČNI MATERIALI
CHEMICAL ANALYSIS, REFERENCE MATERIALS
Instrumenti za analizo / monitoring
Analytical instruments / Monitors
Merilniki izpušnih plinov Gas exhaust analysers
- interni postopek / internal procedure: ML10N128
622. CO (0 do/ to 5) % 1,0 % Kalibracija z referenčnimi mešanicami plinov Calibration with reference gas mixtures
623. CO2 (0 do/ to 16) % 1,0 %
624. O2 (0 do/ to 21) % 1,0 %
625. C3H8 (0 do/ to 2000) ∙ 10-6 1,0 %
Merilniki izpušnih plinov na kompresijski vžig Diesel exhaust analysers
- interni postopek / internal procedure: ML10N130
626. (0 do/ to 9,99) m-1 0,5 % Kalibracija z referenčnimi stekli Calibration with reference glasses 627. (0 do/ to 100) % 0,5 %
pH merilniki z notranjo impedanco: 100Ω/1000MΩ pH measuring equipment with inner impedance of: 100Ω/1000MΩ
- interni postopek / internal procedure: ML10N83
628. (0 do/ to 12,45) pH 0,009 pH Kalibracija s simulacijo, brez sonde Calibration without probe with simulation 629. (-1999 do/ to 1999) mV 0,30 mV
Merilniki prevodnosti tekočin Conductivity measuring equipment
- interni postopek / internal procedure: ML10N83
630. (0,04 do/ to 100) µS/cm 0,2%
Kalibracija s simulacijo, brez sonde Calibration without probe with simulation 631. (0,1 do/ to 800) mS/cm 0,1%
Merilniki slanosti Salinity meters
- interni postopek / internal procedure: ML10N142
632. (0,00005 do/ to 0,0002) kg/kg 1,3 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 32 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
633. (0,0002 do/ to 0,035) kg/kg 0,8 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 33 od 46
3.2.2 Kalibracija se izvaja v enoti v okviru sistema vodenja kakovosti LOTRIČ Meroslovje d.o.o. Calibration is performed at quality system unit within LOTRIČ Metrology Ltd.
QSlab IMS, Cesta Ljubljanske brigade 23a, 1000 Ljubljana
Tabela / Table 3 – kalibracije v laboratoriju / in-lab calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Pospešek
Acceleration
Kalibratorji pospeškomerov
Accelerometer Calibrators
- interni postopek / internal procedure:
ML10N134
634. 10 Hz do/ to 5 kHz 100 mm/s2 do/ to 100 m/s2
1,2 % Kalibracije kalibratorjev pretvornikov
vibracij z variabilno obremenitvijo Transducer Calibrator Calibration with variable load
AKUSTIČNE VELIČINE
ACOUSTICAL QUANTITIES
Raven zvočnega tlaka
Sound Pressure level
0 dB predstavlja 20 µPa
0 dB Corresponds to 20 µPa
Merilniki zvočnega tlaka 94 dB
Sound level meters 94 dB
- interni postopek / internal procedure:
ML10N60
635. 31,5 Hz do/ to 12,5 kHz 0,2 dB
Akustični kalibratorji 94 dB
Acoustic calibrators 94 dB
- interni postopek / internal procedure:
ML10N60
636. 31,5 Hz do/ to 8 kHz 0,2 dB
637. 8 kHz do/ to 12,5 kHz 0,25 dB
Korekcijski faktor mikrofona
Microphone correction factor
- interni postopek / internal procedure:
ML10N60
638. Pri / At 94 dB 250 Hz 0,2 dB
Pistonfon 124 dB
Piston-phone 124 dB
- interni postopek / internal procedure:
ML10N60
639. 250 Hz 0,08 dB
Akustična kalibracija 94 dB
Acoustical calibration 94 dB
- interni postopek / internal procedure:
ML10N60
640. 1000 Hz 0,09 dB
641. 31,5 Hz do/ to 16 kHz 0,11 dB
Akustična kalibracija (94 – 114) dB korak
Acoustical calibration (94 – 114) dB step
- interni postopek / internal procedure:
ML10N60
642. 1000 Hz 0,03 dB
643. 31,5 Hz do/ to 16 kHz 0,11 dB
Popačenje pri (94 – 114) dB
Distortion at (94 – 114) dB
- interni postopek / internal procedure:
ML10N60
644. 31,5 Hz do/ to 16 kHz 0,121 %TD
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 34 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Popačenje pri 124 dB
Distortion at 124 dB
- interni postopek / internal procedure:
ML10N60
645. Merilnik popačenja
Distortion analyser 250 Hz 0,25 d %
Pretvorniki zvočnega tlaka
Transducers of sound level pressure
0 dB predstavlja 1 V/Pa
0 dB Corresponds to 1 V/Pa
Električni del merilnikov zvočnega tlaka
Electrical part of sound level meters
- interni postopek / internal procedure:
ML10N60
646. (40 do/ to 134) dB 31,5 Hz do/ to 12,5 kHz 0,1 dB Najboljša merilna zmogljivost velja za instrumente, katerih mikrofoni imajo znane vse potrebne karakteristike CMC is valid for instruments, whose microphone has all necessary characteristics
647. (40 do/ to 134) dB 31,5 Hz do/ to 200 Hz 0,6 dB
648. (134 do/ to 154) dB 200 Hz do/ to 4 kHz 0,2 dB
649. (124 do/ to 154) dB 4 Hz do/ to 20 kHz 0,6 dB
Pretvorniki zvočnega tlaka
Microphone sound level meters
- interni postopek / internal procedure:
ML10N132
650. - 26 dB do/ to - 60 dB re 1 V 0,1 dB Pretvorniki zvočnega tlaka s predojačevalnikom ali brez Microphone cartridge with or without preamplifier
651. 74 dB do/ to 114 dB re 1 Pa 0,1 dB
Merilniki zvoka
Sound level meters
- interni postopek / internal procedure:
ML10N60
652. 0 dB do/ to - 60 dB re 1 Pa 0,1 dB re 1 Pa Kalibracija s simulacijo brez sonde Calibration with simulation without probe 653. 50 µV do/ to 50 V 89 µV
Pretvorniki vibracij in sile
Vibration and force transducers
Umetni mastoidi
Artificial Mastoids
- interni postopek / internal procedure:
ML10N134
654. Statična sila / Static Force: 5,4 N in / and 2,5 N
0 dB do/ to - 60 dB re 1 V/N 0,6 dB re 1V/N Kalibracija s konstantno statično silo in merjenje hitrosti ob konstantni dinamični sili Calibration with static force and velocity measurement at constant dynamic force.
Merilniki vibracij
Vibration meters
- interni postopek / internal procedure:
ML10N133
655. (0 do/ to 3500) m/s2 0,8 % Kalibracija s simulacijo brez sonde Calibration with simulation without probe 656. 50 µV do/ to 50 V 89 µV
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 35 od 46
3.2.3 Kalibracija se izvaja v enoti v okviru sistema vodenja kakovosti LOTRIČ Meroslovje d.o.o. Calibration is performed at quality system unit within LOTRIČ Metrology Ltd.
QSlab ECHO, Stari trg 37, 3210 Slovenske Konjice
Tabela / Table 4 – kalibracije v laboratoriju / in-lab calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
FLUIDNE VELIČINE
FLUID QUANTITIES
Prostorninski tok plina
Gas volume flow rate
Merilniki pretoka plinov
Gas flow meters
- interni postopek / internal procedure:
ML10N140
657. (0,01 do/ to 100) l/min 2,0 %
Masni tok plinov
Gas mass flow rate
Merilniki pretoka plinov
Gas flow meters
- interni postopek / internal procedure:
ML10N140
658. (0,012 do/ to 120) g/min 2,0 %
Tabela / Table 5 – kalibracije na terenu / on-site calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
FLUIDNE VELIČINE
FLUID QUANTITIES
Prostorninski tok plina
Gas volume flow rate
Merilniki pretoka plinov
Gas flow meters
- interni postopek / internal procedure:
ML10N140
659. (0,01 do/ to 100) l/min 3,5 %
Masni tok plinov
Gas mass flow rate
Merilniki pretoka plinov
Gas flow meters
- interni postopek / internal procedure:
ML10N140
660. (0,012 do/ to 120) g/min 2,0 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 36 od 46
3.2.4 Kalibracija se izvaja v enoti v okviru sistema vodenja kakovosti LOTRIČ Meroslovje d.o.o. Calibration is performed at quality system unit within LOTRIČ Metrology Ltd.
QSL LOTRIČ Mjeriteljstvo, Crnojezerska 18, Laboratorij C2.00, 1000 Zagreb
Tabela / Table 6 – kalibracije v laboratoriju / in-lab calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
ČAS IN FREKVENCA
TIME AND FREQUENCY
Časovni interval
Time interval
Merilniki časa
Timers
- interni postopek / internal procedure:
ML10N111
661. Čas
Time
24 h 0,15 s
DIMENZIONALNE VELIČINE
DIMENSIONAL QUANTITIES
Dolžina
Length
Merila dolžine
Length gauges L – merjena dolžina / measured length
Merilne urice Dial gauges
- interni postopek / internal procedure: ML10N89
662. do/ to 50 mm 1,5 μm + 1·10-5·L Kalibracija samo z obremenjevanjem Calibration with increasing only
Merilniki globine pnevmatik Tire depth gauges
- interni postopek / internal procedure: ML10N89
663. do/ to 50 mm 0,03 mm
Elektronska tipala Electronic probes
- interni postopek / internal procedure: ML10N89
664. do/ to 50 mm 1,5 μm + 1·10-5·L
Kalibracija brez histereze Calibration without hysteresis
Instrumenti za merjenje dolžine
Length measuring instruments
Dvotočkovna vijačna merila (zunanja in notranja) Two point micrometers (external and internal)
- interni postopek / internal procedure: ML10N74
665. do/ to 1000 mm 1,0 μm + 9·10-6·L
ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Pomična merila Vernier calliper gauges
- interni postopek / internal procedure: ML10N72
666. do/ to 1000 mm
7,5 μm + 5·10-5·L ISO 13385:2011 ISO 13225:2012 VDI/VDE/DGQ 2618:2007
Ultrazvočni merilniki debeline Ultrasonic thickness meters
- interni postopek / internal procedure: ML10N120
667. do/ to 50 mm 15 µm + 4·10-3·L
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 37 od 46
Tabela / Table 7 – kalibracije na terenu / on-site calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
ČAS IN FREKVENCA
TIME AND FREQUENCY
Časovni interval
Time interval
Merilniki časa
Timers
- interni postopek / internal procedure:
ML10N111
668. Čas
Time
24 h 0,15 s
DIMENZIONALNE VELIČINE
DIMENSIONAL QUANTITIES
Dolžina
Length
Merila dolžine
Length gauges L – merjena dolžina / measured length
Merilne urice Dial gauges
- interni postopek / internal procedure: ML10N89
669. do/ to 50 mm 1,5 μm + 1·10-5·L Kalibracija samo z obremenjevanjem Calibration with increasing only
Merilniki globine pnevmatik Tire depth gauges
- interni postopek / internal procedure: ML10N89
670. do/ to 50 mm 0,03 mm
Elektronska tipala Electronic probes
- interni postopek / internal procedure: ML10N89
671. do/ to 50 mm 1,5 μm + 1·10-5·L
Kalibracija brez histereze Calibration without hysteresis
Instrumenti za merjenje dolžine
Length measuring instruments
Dvotočkovna vijačna merila (zunanja in notranja) Two point micrometers (external and internal)
- interni postopek / internal procedure: ML10N74
672. do/ to 1000 mm 1,0 μm + 9·10-6·L
ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Pomična merila Vernier calliper gauges
- interni postopek / internal procedure: ML10N72
673. do/ to 1000 mm
7,5 μm + 5·10-5·L ISO 13385:2011 ISO 13225:2012 VDI/VDE/DGQ 2618:2007
Ultrazvočni merilniki debeline Ultrasonic thickness meters
- interni postopek / internal procedure: ML10N120
674. do/ to 50 mm 15 µm + 4·10-3·L
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 38 od 46
3.2.5 Kalibracija se izvaja v enoti v okviru sistema vodenja kakovosti LOTRIČ Meroslovje d.o.o. Calibration is performed at quality system unit within LOTRIČ Metrology Ltd.
QSL LOTRIČ Mjeriteljstvo, Laboratorij C1.00, Prilaz baruna Filipovića 25, 1000 Zagreb
Tabela / Table 8 – kalibracije v laboratoriju / in-lab calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Masa (konvencionalna)
Conventional Mass
Etalonske uteži Standard weights
- interni postopek / internal procedure: ML10N02, ki temelji na / which is based on OIML R 111-1 (2004)
675. 1 mg 0,002 mg
676. 2 mg 0,002 mg
677. 5 mg 0,002 mg
678. 10 mg 0,002 mg
679. 20 mg 0,003 mg
680. 50 mg 0,004 mg
681. 100 mg 0,005 mg
682. 200 mg 0,006 mg
683. 500 mg 0,008 mg
684. 1 g 0,010 mg
685. 2 g 0,012 mg
686. 5 g 0,016 mg
687. 10 g 0,020 mg
688. 20 g 0,025 mg
689. 50 g 0,03 mg
690. 100 g 0,05 mg
691. 200 g 0,10 mg
692. 500 g 0,25 mg
693. 1 kg 0,5 mg
694. 2 kg 1,2 mg
695. 5 kg 8,0 mg
696. 10 kg 16 mg
697. 20 kg 30 mg
698. 50 kg 250 mg
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 39 od 46
3.2.6 Kalibracija se izvaja v enoti v okviru sistema vodenja kakovosti LOTRIČ Meroslovje d.o.o. Calibration is performed at quality system unit within LOTRIČ Metrology Ltd.
QSL LOTRIČ Metrologija, Dragoslava Sreovića, 34000 Kragujevac
Tabela / Table 9 – kalibracije v laboratoriju / in-lab calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
ČAS IN FREKVENCA
TIME AND FREQUENCY
Časovni interval
Time interval
Merilniki časa
Timers
- interni postopek / internal procedure:
ML10N111
699. Čas
Time
24 h 0,15 s
Merilniki obratov
Tachometers
- interni postopek / internal procedure: ML10N138
700. do/ to 60 min-1 0,01 min-1
701. (60 do/ to 300) min-1 0,07 min-1
702. (300 do/ to 600) min-1 0,09 min-1
703. (600 do/ to 4800) min-1 0,6 min-1
704. (4800 do/ to 9960) min-1 0,9 min-1
705. (9960 do/ to 30000) min-1 6 min-1
706. (30000 do/ to 60000) min-1 7 min-1
707. (60000 do/ to 99999) min-1 9 min-1
DIMENZIONALNE VELIČINE
DIMENSIONAL QUANTITIES
Dolžina
Length
Merila dolžine
Length gauges L – merjena dolžina / measured length
Merilne urice Dial gauges
- interni postopek / internal procedure: ML10N89
708. do/ to 50 mm 1,5 μm + 1·10-5·L Kalibracija samo z obremenjevanjem Calibration with increasing only
Merilniki globine pnevmatik Tire depth gauges
- interni postopek / internal procedure: ML10N89
709. do/ to 50 mm 0,03 mm
Elektronska tipala Electronic probes
- interni postopek / internal procedure: ML10N89
710. do/ to 50 mm 1,5 μm + 1·10-5·L Kalibracija brez histereze Calibration without hysteresis
Instrumenti za merjenje dolžine
Length measuring instruments
Dvotočkovna vijačna merila (zunanja in notranja) Two point micrometers (external and internal)
- interni postopek / internal procedure: ML10N74
711. do/ to 1000 mm 1,0 μm + 9·10-6·L ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Pomična merila Vernier calliper gauges
- interni postopek / internal procedure: ML10N72
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 40 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
712. do/ to 1000 mm 7,5 μm + 5·10-5·L ISO 13385:2011 ISO 13225:2012 VDI/VDE/DGQ 2618:2007
Ultrazvočni merilniki debeline Ultrasonic thickness meters
- interni postopek / internal procedure: ML10N120
713. do/ to 20 mm 15 µm + 4·10-3·L
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Sila
Force
Pretvorniki sile Force transducers
- interni postopek / internal procedure: ML10N47
714. (>1 do/ to 10) N 0,011 N
715. (10 do/ to 400) N 0,11 N
716. (400 do/ to 600) N 0,12 N
717. (600 do/ to 1000) N 0,13 N
Masa (konvencionalna)
Conventional Mass
Etalonske uteži Standard Weights
- interni postopek / internal procedure: ML10N02, ki temelji na / which is based on OIML R 111-1 (2004)
718. 1 mg 0,06 mg
719. 2 mg 0,06 mg
720. 5 mg 0,06 mg
721. 10 mg 0,08 mg
722. 20 mg 0,10 mg
723. 50 mg 0,12 mg
724. 100 mg 0,16 mg
725. 200 mg 0,20 mg
726. 500 mg 0,25 mg
727. 1 g 0,3 mg
728. 2 g 0,4 mg
729. 5 g 0,5 mg
730. 10 g 0,6 mg
731. 20 g 0,8 mg
732. 50 g 1,0 mg
733. 100 g 1,6 mg
734. 200 g 3,0 mg
735. 500 g 8,0 mg
736. 1 kg 16 mg
737. 2 kg 30 mg
738. 5 kg 80 mg
739. 10 kg 160 mg
740. 20 kg 300 mg
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 41 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Tehtnice
Weighing instruments
m = masa / mass
Neavtomatske tehtnice
Non-automatic weighing instruments
- interni postopek / internal procedure: ML10N01, ki temelji na / which is based on EURAMET / cg-18 / v.04 / 2015
741. do/ to 0,02 g 0,008 mg
742. (0,02 do/ to 0,05) g 0,009 mg
743. (0,05 do/ to 0,1) g 0,010 mg
744. (0,1 do/ to 0,2) g 0,011 mg
745. (0,2 do/ to 0,5) g 0,015 mg
746. (0,5 do/ to 1) g 0,017 mg
747. (1 do/ to 2) g 0,018 mg
748. (2 do/ to 5) g 0,022 mg
749. (5 do/ to 10) g 0,034 mg
750. (10 do/ to 50) g 0,06 mg
751. (50 do/ to 100) g 0,09 mg
752. (100 do/ to 200) g 0,18 mg
753. (200 do/ to 500) g 0,34 mg
754. (0,5 do/ to 50) kg m·(2,0·10-6)
755. (50 do/ to 2000) kg m·(2,5·10-4)
Moment sile
Torque
Momentni ključi Torque Wrenches
- interni postopek / internal procedure: ML10N70
756. (0,1 do/ to 0,2) Nm 1,2 % ISO 6789:2003
757. (0,2 do/ to 1) Nm 1,0 %
758. (1 do/ to 2) Nm 0,9 %
759. (2 do/ to 10) Nm 0,8 %
760. (10 do/ to 20) Nm 1,1 %
761. (20 do/ to 1000) Nm 0,9 %
762. (1000 do/ to 2000) Nm 0,8 %
763. (2000 do/ to 3000) Nm 0,7 %
TEMPERATURA, VLAGA IN TERMOFIZIKALNE LASTNOSTI
TEMPERATURE, HUMIDITY AND THERMO-PHYSICAL PROPERTIES
Temperatura
Temperature
Termometri s prikazovalnikom in zunanjimi sondami Thermometers with indicators and external probes
- interni postopek / internal procedure: ML10N26
764. 0 °C 0,15 °C
765. (25 do/ to 200) °C 0,15 °C
766. (200 do/ to 300) °C 0,40 °C
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 42 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
767. (300 do/ to 400) °C 0,45 °C
Vlažnost
Humidity
Merilniki relativne vlažnosti Relative humidity sensors
- interni postopek / internal procedure: ML10N147
768. pri / at (20 do/ to 30) °C 11,3 % 1,8 % Kalibracija v fiksnih točkah z uporabo referenčnega merilnika relativne vlage Calibration in fixed points using reference relative humidity sensor
769. 32,9 % 1,6 %
770. 53,1 % 2,0 %
771. 74,8 % 2,0 %
772. 83,9 % 2,4 %
773. 96,8 % 2,8 %
KEMIJSKA ANALIZA, REFERENČNI MATERIALI
CHEMICAL ANALYSIS, REFERENCE MATERIALS
Instrumenti za analizo / monitoring
Analytical instruments / monitors
pH merilniki z notranjo impedanco: 100Ω/1000MΩ pH measuring equipment with inner impedance of: 100Ω/1000MΩ
- interni postopek / internal procedure: ML10N83
774. (0 do/ to 12,45) pH 0,05 pH Kalibracija s simulacijo, brez sonde. Calibration without probe with simulation 775. (-1800 do/ to 1800) mV 1,2 mV
Merilniki prevodnosti tekočin Conductivity measuring equipment
- interni postopek / internal procedure: ML10N83
776. (0,04 do/ to 1000) µS/cm 0,3%
Kalibracija s simulacijo, brez sonde / Calibration without probe with simulation 777. (1 do/ to 800) mS/cm 0,3%
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 43 od 46
Tabela / Table 10 – kalibracije na terenu / on-site calibrations
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
ČAS IN FREKVENCA
TIME AND FREQUENCY
Časovni interval
Time interval
Merilniki časa
Timers
- interni postopek / internal procedure:
ML10N111
778. Čas
Time
24 h 0,15 s
Merilniki obratov
Tachometers
- interni postopek / internal procedure: ML10N138
779. do/ to 60 min-1 0,01 min-1
780. (60 do/ to 300) min-1 0,07 min-1
781. (300 do/ to 600) min-1 0,09 min-1
782. (600 do/ to 4800) min-1 0,6 min-1
783. (4800 do/ to 9960) min-1 0,9 min-1
784. (9960 do/ to 30000) min-1 6 min-1
785. (30000 do/ to 60000) min-1 7 min-1
786. (60000 do/ to 99999) min-1 9 min-1
DIMENZIONALNE VELIČINE
DIMENSIONAL QUANTITIES
Dolžina
Length
Merila dolžine
Length gauges L – merjena dolžina / measured length
Merilne urice Dial gauges
- interni postopek / internal procedure: ML10N89
787. do/ to 50 mm 1,5 μm + 1·10-5·L Kalibracija samo z obremenjevanjem Calibration with increasing only
Merilniki globine pnevmatik Tire depth gauges
- interni postopek / internal procedure: ML10N89
788. do/ to 50 mm 0,03 mm
Elektronska tipala Electronic probes
- interni postopek / internal procedure: ML10N89
789. do/ to 50 mm 1,5 μm + 1·10-5·L Kalibracija brez histereze Calibration without hysteresis
Instrumenti za merjenje dolžine
Length measuring instruments
Dvotočkovna vijačna merila (zunanja in notranja) Two point micrometers (external and internal)
- interni postopek / internal procedure: ML10N74
790. do/ to 1000 mm 1,0 μm + 9·10-6·L ISO 3611:2011 VDI/VDE/DGQ 2618:2007
Pomična merila Vernier calliper gauges
- interni postopek / internal procedure: ML10N72
791. do/ to 1000 mm 7,5 μm + 5·10-5·L ISO 13385:2011 ISO 13225:2012 VDI/VDE/DGQ 2618:2007
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 44 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
Ultrazvočni merilniki debeline Ultrasonic thickness meters
- interni postopek / internal procedure: ML10N120
792. do/ to 20 mm 15 µm + 4·10-3·L
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Sila
Force
Pretvorniki sile Force transducers
- interni postopek / internal procedure: ML10N47
793. (>1 do/ to 10) N 0,011 N
794. (10 do/ to 400) N 0,11 N
795. (400 do/ to 600) N 0,12 N
796. (600 do/ to 1000) N 0,13 N
Tehtnice
Weighing instruments
m = masa / mass
Neavtomatske tehtnice Non-automatic weighing instruments
- interni postopek / internal procedure: ML10N01, ki temelji na / which is based on EURAMET / cg-18 / v.04 / 2015
797. do/ to 0,02 g 0,008 mg
798. (0,02 do/ to 0,05) g 0,009 mg
799. (0,05 do/ to 0,1) g 0,010 mg
800. (0,1 do/ to 0,2) g 0,011 mg
801. (0,2 do/ to 0,5) g 0,015 mg
802. (0,5 do/ to 1) g 0,017 mg
803. (1 do/ to 2) g 0,018 mg
804. (2 do/ to 5) g 0,022 mg
805. (5 do/ to 10) g 0,034 mg
806. (10 do/ to 50) g 0,06 mg
807. (50 do/ to 100) g 0,09 mg
808. (100 do/ to 200) g 0,18 mg
809. (200 do/ to 500) g 0,34 mg
810. (0,5 do/ to 50) kg m·(2,0·10-6)
811. (50 do/ to 2000) kg m·(2,5·10-4)
Moment sile
Torque
Momentni ključi Torque Wrenches
- interni postopek / internal procedure: ML10N70
812. (0,1 do/ to 0,2) Nm 1,2 % ISO 6789:2003
813. (0,2 do/ to 1) Nm 1,0 %
814. (1 do/ to 2) Nm 0,9 %
815. (2 do/ to 10) Nm 0,8 %
816. (10 do/ to 20) Nm 1,1 %
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 45 od 46
Št.
No
Merjena veličina,
(pod)področje, oz.
merilni instrumenti in/ali
območje (merjene
veličine).
Measured quantity, (sub-) field, and/or instruments, and/or range (of measured quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity) or
Limitations, conditions, influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and measurement Capability (CMC) Expressed as an Expanded Uncertainty.*
- Tip kalibracijske metode,
kalibracijski postopek.
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method, internal calibration procedure
- Measuring instruments (option)**
- Remarks
817. (20 do/ to 1000) Nm 0,9 %
818. (1000 do/ to 2000) Nm 0,8 %
819. (2000 do/ to 3000) Nm 0,7 %
TEMPERATURA, VLAGA IN TERMOFIZIKALNE LASTNOSTI
TEMPERATURE, HUMIDITY AND THERMO-PHYSICAL PROPERTIES
Temperatura
Temperature
Termometri s prikazovalnikom in zunanjimi sondami Thermometers with indicators and external probes
- interni postopek / internal procedure: ML10N26
820. 0 °C 0,15 °C
821. (25 do/ to 200) °C 0,15 °C
822. (200 do/ to 300) °C 0,40°C
823. (300 do/ to 400) °C 0,45 °C
Vlažnost
Humidity
Merilniki relativne vlažnosti Relative humidity sensors
- interni postopek / internal procedure: ML10N147
824. pri / at (20 do/ to 30) °C 11,3 % 1,8 % Kalibracija v fiksnih točkah z uporabo referenčnega merilnika relativne vlage Calibration in fixed points using reference relative humidity sensor
825. 32,9 % 1,6 %
826. 53,1 % 2,0 %
827. 74,8 % 2,0 %
828. 83,9 % 2,4 %
829. 96,8 % 2,8 %
KEMIJSKA ANALIZA, REFERENČNI MATERIALI
CHEMICAL ANALYSIS, REFERENCE MATERIALS
Instrumenti za analizo / monitoring
Analytical instruments / monitors
pH merilniki z notranjo impedanco: 100Ω/1000MΩ pH measuring equipment with inner impedance of: 100Ω/1000MΩ
- interni postopek / internal procedure: ML10N83
830. (0 do/ to 12,45) pH 0,05 pH Kalibracija s simulacijo, brez sonde. Calibration without probe with simulation 831. (-1800 do/ to 1800) mV 1,2 mV
Merilniki prevodnosti tekočin Conductivity measuring equipment
- interni postopek / internal procedure: ML10N83
832. (0,04 do/ to 1000) µS/cm 0,3%
Kalibracija s simulacijo, brez sonde / Calibration without probe with simulation 833. (1 do/ to 800) mS/cm 0,3%
* CMC opomba / CMC Note
Razširjena negotovost je podana kot kombinirana standardna negotovost pomnožena s takšnim faktorjem pokritja k, da
določa interval zaupanja približno 95 %. / Expanded uncertainty of measurement is stated as the standard uncertainty of
measurement multiplied by the coverage factor k such that the coverage probability corresponds to approximately 95 %.
** Navedba informacije o merilnih instrumentih se v tej koloni uporabi le v tistih primerih, kjer to ne izhaja že iz opredelitve
veličine, opisa (pod)področja in instrumentov v drugi koloni tabele. / Information on measuring instruments are specified
in this column only if it is not clear from the description of quantity, (sub-) field, and/or instruments in the second column
of this table.
Priloga k akreditacijski listini št. / Annex to the Accreditation Certificate No. LK-008
Datum izdaje / Issued on 31. julij 2017
Zamenjuje izdajo z dne / Replaces Annex dated 6. marec 2017
Veljavnost akreditacije je mogoče preveriti na: Information on current accreditation status is available at:
www.slo-akreditacija.si
OB05-32 Izdaja 7 Stran 46 od 46
*** Kadar je za enoumno razumevanje zmogljivosti potreben opis robnih pogojev, vplivnih veličin ali drugih omejitev se ti
navajajo v tej koloni (z enoumno oznako kolone), območje merjene veličine pa je v takem primeru določeno že v drugi
koloni te tabele. / When a description of the boundary conditions, influence quantity or other limits is required for an
unequivocal understanding of capabilities it is specified in this column (clearly indicated), providing that the range of
measured quantity is defined in the second column of this table.
Direktor / Director dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu. Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.