KE Lee in Tektronix
description
Transcript of KE Lee in Tektronix
KE Lee in Tektronix
오실로스코프를 이용한 측정방법
2
레이다 관련 측정장비
.
-. Oscilloscope
-. Pulse Counter
-. Signal Source
-. Power Meter
3
오실로스코프 측정기능
.
-. 전압-. 전류-. 주파수-. Amplitude-. 지터-. Power
4
.
전압
.
-. 최소 / 최대 측정전압 : 1mV-40kV-. probe name: BNC-P6015- 감쇄비 : 1X,1000X
전류-. 최대 측정전류 : 20kA Peak-. probe name: P6021 w/CT4- 감쇄비 : 1000X
5
주파수
.
-. 최대 측정 주파수 : 6GHz-. name: TDS6604
지터-. Period, Cycle, Random, Total jitter.
Power-. True, 역률 , Dynamic Road, Peak Finder
6
지터 (Jitter)란 ?
.
– What is jitter?– “The deviation of an edge from where it should be”
– Jitter is caused by:– (among other things)– Thermal noise– Crosstalk– Injected noise (EMI/RFI)– Circuit instabilities
7
.
Jitter Measurement Summary
P2 P3 P4P1
Period Jitter = 18.3ps RMS (0.990/1.010/0.980/1.020)
Cy-Cy Jitter = 36.1ps RMS (0.020/-0.030/0.040)
TIE = 9.6ps RMS (-0.010/0.000/-0.020/0.000)
0.990ns 1.010ns 0.980ns 1.020ns
0.0ns 0.990ns 2.000ns 2.980ns 4.000ns
0.020ns -0.030ns 0.040ns
-0.010ns 0.000ns -0.020ns 0.000ns
period
cy-cy
TIE
8
.
Total Jitter
– Total jitter is the sum of all these effects
Random components
Tj=(N*Rj)+Dj - Total Jitter where N is desired sigma
Deterministic jitter
9
.
ET Cursor Method
10
.
TDSJIT3 Real Time Method
– Proprietary Rj/Dj Separation and BER Estimation
– Based on real time acquisition data
– Includes Golden PLL TIE measurements
– Spectral Analysis used to decompose jitter
– Wide noise margin – works even with substantial system noise
– Works with short or long data repeats – no pattern details required (you provide bit rate and pattern length)
– Trigger at any random point in your data
– Works with CSA7000, TDS5000, TDS6000, TDS7000 instruments
– Results for Rj, Dj, Pj, DDj, DCD, BER
11
.
Power Supply and Measurements
True Power
Apparent Power
Power Factor
Current harmonic
Total Harmonic Distortion
(THD)
Switching LossRDS on
SOAModulation Analysis
40KHzCLOCK
L
N
G
D
S
G
Core LossB-H Analysis
12
.
Oscilloscope Based Power Measurement and Analysis for
13
TDSJIT3 – TIE: Rj/Dj - BER
– Displays results for Rj/Dj– Rj/Dj results are only
available for TIE and PLL TIE measurements
– Rj/Dj is a two step process: make the TIE measurement; then calculate Rj/Dj
– Rj/Dj requires a repeating pattern, such that 100 repeats are captured in a single acquisition
– You must know and enter the pattern length Rj is RMS, Dj is Pk-Pk, Tj is Pk-Pk …
14
THANK YOU FOR YOUR ATTENDANCE