DS DDMMV2.1 EN - Variometrum webáruház · DDMMV2.1, which name is short for “Digital Dream...
Transcript of DS DDMMV2.1 EN - Variometrum webáruház · DDMMV2.1, which name is short for “Digital Dream...
请在这里输入您的公司名称
WWW.DDCNC.COM
DDUM CARD V1.0
Simple Description
(English)
WWW.DDCNC.COM
USB-LPT MACH3 CNC
CARD V2.1
Manual
(EN)
DDMMV2.1
FASTERCNC CO.,LTD FASTERCNC CO., LTD.
DDREAMCNC CO., LTD.
M WWW.DDCNC.COM
DD
LM
V2.1 M
anual
目 录
Chapter 1 Overview .............................................................................................................................................. 1
1.1 Simply Introduction ................................................................................................................................ 1
1.2 Requirements of Computer ..................................................................................................................... 1
1.3 Appearance and size of poduct ............................................................................................................... 2
1.4 Notes and Cautions ................................................................................................................................. 4
Chapter 2 Detailed Features .................................................................................................................................. 5
2.1 Electrical parameters ............................................................................................................................... 5
2.2 Functions and define of each module ..................................................................................................... 5
Chapter 3 Software Installation .......................................................................................................................... 10
3.1 MACH3 Install ..................................................................................................................................... 10
3.2 MACH3 Registration ............................................................................................................................ 13
3.3 USBPlug-in installation ........................................................................................................................ 13
Chapter 4 Software uses ..................................................................................................................................... 14
4.1 Open Software ...................................................................................................................................... 14
4.2 Software Common settings ................................................................................................................... 15
Chapter 5 Q& A ................................................................................................................................................ 19
C ontens
Ch
ap
ter 01
Ov
erview
WWW.DDCNC.COM
1
Chapter 1 Overview
1.1Simply Introduction
DDMMV2.1, which name is short for “Digital Dream Multiple input Mach3 card
Version 2.1”is a CNC system based mach3. This card is designed by our Studio You do not
need to add other Hardware,and you can complete the signal conversion from the G-code to
the movement of the stepper motor drive control. You should use both parallel port and usb port at
the same time.This card is compatible with most stepper drives and servo drives. And it is perfect
weapon to replace mach3 parallel interface board.
1.2Requirements of Computer
Basic Configuration:
1) CPU:1GHz
2) Memory:512MB
3) 500MB Available disk space
4) USB 2.0
5) LPT port
Recommended configuration:
� CPU:2GHz Dual Core
� Memory:2GB
� 1G Available disk space
� USB 2.0
� LPT port
Ch
ap
ter 01
Ov
erview
WWW.DDCNC.COM
2
1.3 Appearance and size of product
� 1、USB communication
interface, and power
supply for the board;
� 2 、 LPT port for
stepper driver signal.
� 3、8 IO outputs ,opto-isolated;
� 4、spindle outputs signal;
� 5、hand control box port;
� 6、6 axis stepper dirver signal output;
� 7、15 IO input, opto-isolated, It Can be configured to limit the emergency stop and
other functions.
� 8、Use STM32 chip as a Master ;
Ch
ap
ter 01
Ov
erview
WWW.DDCNC.COM
3
Figure1-1. Product Outline
See as Figure 1-1,this card’s size is 85.6*98.2mm,its installation holes’location is 79.3*80.1mm.
Figure1-2. Overall appearance
Ch
ap
ter 01
Ov
erview
WWW.DDCNC.COM
4
1.4 Notes and Cautions
� Prohibits the rain, boards for high-performance precision equipment, rain can
cause short-circuit
� CAUTION WARNING, various wiring in strict accordance with installation
Description document specification.
� High risk, boards need to stay away from high-pressure.
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
5
Chapter 2 Detailed Features
2.1 Electrical parameters
A. Operating voltage of input interface:12V;
B. Operating voltage of output interface:12V;
C. stepper motor control signal output voltage:5V;
NOTE: The marked as “USB” is Power input and communication interface, you should
connected correctly.
2.2 Functions and define of each module
Figure 2-1 Functional modules defined in Figure
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
6
� A)USB PORT,This interface is connected to the computer through a USB line.You can
use the software mach3 to control this board, Note that you should use a USB2.0 cable
with shielding and ferrite core,and cable length should be not more than 2 meters.This
USB port not only provides power to the board, but also manages output&input port、
hand control box interface and spindle control port.
� B)LPT port.LPT port should be connected to parallel port of PC.LPT port only manages
6axis stepper motor driver.
� C)Input port to parallel port. There are input10\11\12\13 of parallel port. Wiring
methods see as Figure 2-2,you can link a Micro Switch to GND and INLX(X can be 10
11 12 13). Internal circuit of INPUT10\11\12\13 see as Figure2-3.
Figure 2-2 Input port to parallel port
Figure 2-3 Internal circuit of INPUT10\11\12\13
� D) 8 General IO output interface, Have a current drive capability within 5MA,defined
as 12V O1、O2、O3、O4、O5、O6、O7、O8、GND from left to right. See as figure2-4.
Internal circuit . OUT1 is system reserved,you can not use it.
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
7
Figure 2-4 8 General IO output interface
Figure 2-5 Internal circuit of 8 General IO output interface
� E) Spindle control output port, See as Figure 2-5,. It is defined as GND ,CW
(Clockwise control output),CCW(Counterclockwise control output),VSP (0-10V
output to frequency converter )。
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
8
Figure 2-5 Spindle control output port connect to Frequency Converter
� F)Hand control box port,RS232port, Wiring methods see as Figure 2-6.The function of
Hand control box see as next Section.
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
9
Figure 2-6 Wiring methods of Hand control box
� G)6-axis stepper motor control signal output,defined as DIR-\CP-\COM .They are
negative direction, negative pulse, positive common. These port are common positive
connection. This board does not support the common negative connection. Wiring
method refer to Figure 2-6.This card doesn’t have EN signal, Most drives on sale should
not connected to the EN signal. It is defined as X \ Y \ Z \ A \ B channel from top to
bottom, Wire methods see as Figure 2-6. COM connect to both SP+ DIR+ of Driver;CP-
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
10
connect to SP- of Driver; DIR- connect to DIR- of Driver.
Figure 2-7 Stepper motor driver connection method
� H) General INPUT PORT from USB ,IN1-15,see as Figure 2-8,it is defined as GND、
INP01、INP02、INP03、INP04、INP05、GND、INP06、INP07、INP08、INP09、
INP10、GND、INP11、INP12、INP13、INP14、INP15 from left to right, The interface
uses opto-isolated, using common negetive input, GND is used as the common Port.
These input port is Managed by USB port.Wiring methods see as Figure 2-8。
Ch
ap
ter 2 D
etailed
Fea
tures
WWW.DDCNC.COM
11
Figure 2-8 Stepper motor driver connection method
� J )PROBE input port. This port is connected to PROBE, it’s something used to Tool
setting.Wire method see as Figure 2-9
Figure 2-8 Stepper motor driver connection method
Ch
ap
ter 3 S
oftw
are In
stalla
tion
WWW.DDCNC.COM
12
Chapter 3 Software Installation
3.1 MACH3 Install
When you purchase our product, we will supply a CD-ROM, which contains the MACH3 installation, registration, and USB plug-ins. See as Figure 3-1.
Figure 3-1. CD-ROM Screenshot
First run the installation Mach3Version3.043.066 .Into the first page. See as Figure 3-2.
Ch
ap
ter 3 S
oftw
are In
stalla
tion
WWW.DDCNC.COM
13
Figure 3-2. MACH3 installation process 1
Click Next and then enter the page shown in Figure 3-3.
Figure 3-3. MACH3 installation process 2
Select the consent agreement, click Next, See as Figure 3-4
Ch
ap
ter 3 S
oftw
are In
stalla
tion
WWW.DDCNC.COM
14
Figure 3-4. MACH3 installation process 3
Select the installation path, click Next (it can be installed on any disk, and recommended to install the C drive or the D drive) See as Figure 3-5
Figure 3-5. MACH3 installation process 4
Click Next until completion. Then restart the computer.
Ch
ap
ter 3 S
oftw
are In
stalla
tion
WWW.DDCNC.COM
15
3.2 MACH3 Registration
Copy the file Mach1Lic.dat in The CD-ROM to mach3 installation path (eg C :/ MACH3) .
3.3 USB Plug-in installation
Copy the file DDMMV2.1A.dll to X:\Mach3\PlugIns.
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
16
Chapter 4 Software uses
4.1 Open Software
Double-click the mach3mill .
Enter mach3 software.
4.2 Software Common settings
� DDMM plugin setting
Figure4-1. get in config plugins
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
17
Figure4-2. Plugin dialog
Figure4-3. Enable the DDMM plugin
See as Figure4-2,In this dialog ,you should click the red cross in the circle.Change it to “ √”as Figure4-3.
Then click “OK”.
� Motor operating parameters setting
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
18
Figure4-4. Motor operating parameter setting menu entry
See as Figure 4-3.From submenu “motor tuning” of the menu “config” into the motor parameter settings dialog. See as Figure 4-4.
Figure4-5. Motor operating parameter settings dialog
The parameters are defined as follows: Steps per:Pulse equivalent ,it is number of pulses required with axial movement 1mm, This can be calculated by lead screw pitch and motor drive segment. Such as pitch 2.5mm,2-phase motor 8 segments, Calculation method is 8*200/2.5=640。 Velocity:The speed is the axial velocity, Units is mm/s,Recommended settings 1500. Acceleration:Units is mm/s2,Recommended settings 200. Step Pulse:Minimum pulse width,Recommended settings 2. Dir Pulse:Minimum width direction, Recommended settings 2. Attention:The parameters for each axis is not necessarily the same,To select the axis,
and then set parameters. You should click “SAVE AXIS SETTINGS” After setting.
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
19
� Port Settings
Figure4-6. Port settings
See as Figure 4-6,Click the sub-menu “ports and pins” of menu “Config” into Port Settings dialog box.See as Figure 4-7.
Figure4-7. Port Settings dialog box
The sub-pages you need to set include “Motor Outputs”, “Input Signals”, “Output Signals” and “Spindle Setup”.First Click to enter “Motor Outputs”. See as Figure4-8.
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
20
Figure4-8. Stepper motor port settings dialog
Click “Input Signals” Into the input signal settings page. See as Figure4-9
Figure4-9. IO Input Settings dialog box Here you can configure according to your actual needs the corresponding function. Optional Function include XYZAB5axis’s Upper and lower limit、XYZABC5axis’s HOME point、PROBE、ESTOP, etc. The board has19 input signals in total,See as Figure4-9,there are 4 in signal belong to PORT1,and 15 IN signal belong to PORT3, Customers can choose according
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
21
to their needs, in accordance with the pin numbers, define the corresponding function. Click “Output Signals” to enter the Output signal setting page. See as Figure 4-10.There are 9 output in total.You can set OUT2-OUT8 as normal ouput, OUT1 is system reserved,you
can not use it.All output signals belong to Port#2 , See as Figure4-10
Figure4-10. Output Signal Setup dialog
Ch
ap
ter 4 S
oftw
are u
ses
WWW.DDCNC.COM
22
Figure4-11. Spindle Setup1
Click Spindle Setup to get into Spindle page.Please select “use spindle motor output” if required PWM speed spindle. And select “ PWM Control”.Spindle Setup see as Figure 4-11, set CW and CCW as output10 and output11. PWM port can’t be set. You can only set Frequent of PWMBase. Output#1~output#6 in Output Signal Setup dialog can be Configured into Mist and Flood too. You can set them like CW and CCW.Here we note correspondence between 2 page.
Ch
ap
ter 5 C
on
tact u
s an
d Q
&A
WWW.DDCNC.COM
23
Chapter 5 Contact us andQ& A
� Company Website:ddcnc.com;
� Technical Support email:[email protected];
� Technical Support qq:649631655;
Figure 5-1 All Component in a box