26.00(660)

13.00(330)

11.88(302)

7.38(187) 14.75

(375)

20.00(508)

1.06(27)

2.62(67)

4.50(114)

1.13(29)

1.(3

3.75(95)

5.81(148)

A17.00(432)

4.31(109)

11.75(298)

23.50(597)25.76(654)

B 2.125(54)

1.31 DIA.(33)4 MOUNTING HOLES

23.25(591)

C

3.38(86)

8.50(216)

4.88(124)

(

CLCC DRUM 12.75 DIA.(324)

)

22.75 DIA.(578)

HOISTINGPORT

LOWERINGPORT

CH230A23,000 LB First Layer Line Pull

DIMENSIONAL INFORMATION

COPYRIGHT 2004PACCAR WINCH DIVISION

LIT2179APRIL 2004

PRINTED IN U.S.A. CH230A

High efficiency planetary gearing Optional Hydraulic Motor High Capacity Overrunning Clutch Patented Braden Brake Valve for Smooth Operation

A B C090 9.00 5.38 35.95110 9.50 5.63 36.20120 9.75 5.75 36.32

(2-SPD) 127 15.00 8.56 40.69

MOTOR

VARIABLESDIMENSIONS

PACR WINCH DIVISION

www.paccarwinch.com

P.O. Box 547 Broken Arrow, Oklahoma 74013PHONE: (918) 251-8511 FAX: (918) 259-1575

ROPE ROPESIZE CAPACITY(IN.) (LBS.) (KG) (FPM) (MPM) (LBS.) (KG) (FPM) (MPM) (LBS.) (KG) (FPM) (MPM) (FEET) (M)

1 17,200 7,800 289 88 21,700 9,845 298 91 23,000 10,430 301 90 80 242 15,500 7,030 321 98 19,500 8,845 331 101 20,700 9,390 335 102 169 523 14,100 6,395 353 108 17,700 8,030 364 111 18,800 8,530 368 112 266 814 12,900 5,850 385 117 16,200 7,350 397 121 17,200 7,800 402 123 372 1135 11,900 5,395 417 127 15,000 6,805 430 131 15,900 7,210 435 133 487 1486 11,100 5,035 449 137 13,900 6,305 463 141 14,800 6,715 469 143 611 1861 16,900 7,665 291 89 21,500 9,750 300 91 22,800 10,340 304 93 69 212 15,000 6,805 328 100 19,100 8,665 339 103 20,200 9,160 343 105 147 453 13,500 6,125 366 112 17,100 7,755 377 115 18,200 8,255 382 116 234 714 12,200 5,535 403 123 15,500 7,030 416 127 16,500 7,485 420 128 330 1015 11,200 5,080 440 134 14,200 6,440 454 138 15,100 6,850 459 140 435 133

12.03 CU. IN. DISP.2900 PSI @ 170 GPM

11.03 CU. IN. DISP.

LINE SPEED LINE PULL LINE SPEEDLINE PULL3000 PSI @ 155 GPM

7/8

3/4

9.02 CU. IN. DISP.3000 PSI @ 125 GPM

L

A

Y

E

R

LINE PULL LINE SPEED

SINGLE SPEED 36:1 RATIO DRUM 955 LBS. WEIGHT 01120 MOTOR090 MOTOR 110 MOTOR

PERFORMANCE INFORMATION

NOTES

ROPE ROPESIZE CAPACITY(IN.) (LBS.) (KG) (FPM) (MPM) (LBS.) (KG) (FPM) (MPM) (FEET) (M)

1 23,000 10,430 126 38 8,900 4,035 271 83 80 242 20,700 9,390 140 43 8,000 3,630 302 92 169 523 18,800 8,530 154 47 7,200 3,265 332 101 266 814 17,200 7,800 168 51 6,600 2,995 362 110 372 1135 15,900 7,210 182 55 6,100 2,765 392 119 487 1486 14,800 6,710 196 60 5,700 2,585 422 129 611 1861 22,800 10,340 127 39 8,800 3,990 274 84 69 212 20,200 9,160 143 44 7,800 3,540 309 94 147 453 18,200 8,255 159 48 7,000 3,175 344 105 234 714 16,500 7,485 176 54 6,300 2,860 379 116 330 1015 15,100 6,850 192 59 5,800 2,630 414 126 435 133

L

A

Y

E

R LINE PULL LINE SPEED LINE PULL LINE SPEED

2-SPEED MOTOR 36:1 RATIO 2700 PSI @ 85 GPM DRUM 960 LBS. WEIGHT 01

HIGH SPEED6.37 CU. IN. DISP.

3/4

7/8

12.74 CU. IN. DISP.LOW SPEED

CH230A

Specifications are subject to change without notification and withoutincurring obligation.

Pressure and flow shown are the maximum allowable for the particularcombination of winch, ratio, motor and drum.

Specifications in this publication are theoretical and may vary dependingon hydraulic system, environment, etc.

Line pulls are maximum ratings for the winch only. Wire rope ratingsmay be lower than the winch rating. Consult the wire rope manufacturerfor ratings.

A minimum of 5 wraps of wire rope mustbe left on the drum to prevent the loadfrom being supported by the wire ropeanchor alone. Since the wire rope anchoris not designed to hold the rated load, fail-ure to leave 5 wraps of wire rope on thedrum could cause the load to drop, whichcould result in property damage, injury ordeath.

OPTIONSConsult the factory for high pressure piston motors

and available ratios.

MINIMUM GPM RECOMMENDATION FOR SMOOTH OPERATION*

MOTOR 120 - 28 GPMMOTOR 110 - 27 GPMMOTOR 090 - 24 GPMMOTOR 127 - 24 GPM

*RECOMMENDED MINIMUM SYSTEM FLOW SHOULD BE 2X THESE VALUES.