APS Stamp Color Concrete
Transcript of APS Stamp Color Concrete
中亞建築系統(國際)有限公司
APS Construction Systems (International) Ltd.
香港北角屈臣道4-6號海景大廈B座10樓1009室
Rm. 1009, 10/F., Block B, Sea View Estate,
4-6 Watson Rd, North Point, H K
Tel.: (852) 2979 0890 Fax.: (852) 2979 0499
Email: [email protected]
Website: www.apsconst.com
All Intellectual Property Rights are Reserved &
Protected by APS Construction System
International Limited
1
We provide the latest innovations in specialized architectural decorative stamp and overlay stamp colored concrete finishes that will captivate the Fashion and Beauty of your exterior and interior premises at the very least cost. Consistency, Durability & Environmental Friendly makes our Quality at forefront.
With over 15 years experience and technical skill in workmanship, we do not only sell to you our products but offers you a long term solution for your flooring needs.
2
3
KT008B KT009 KT010
KT0011 KT0012 KT0013
APS 2012
4
KT014A KT014B KT014C
KT015 KT016A KT016B
APS 2012 5
KT017 KT018B
KT020
KT019A
KT021 KT022
APS 2012 6
KT023 KT024A KT024B
KT025 KT026 KT027
APS 2012
7
KT028 KT029 KT030
KT031 KT032 KT033A
APS 2012 8
KT033C KT033B KT033D
KT033E KT034 KT035
APS 2012 9
KT036A KT036B KT036C
KT037A KT037B KT038
APS 2012 10
KT039 KT040 KT041
KT045 KT046 KT047
APS 2012 11
KT048 KT049
KT050 KT051
APS 2012 12
KLT-01A-1 KLT-01A-2 KLT-02B
KLT-03A-1 KLT-03A-2 KLT-03B-1
APS 2011 13
KLT03B-2 KLT-05-1 KLT-05-2
KLT-06-1 KLT-06-2 KLT-06-3
APS 2011 14
KLT-07-1 KLT-07-2 KLT-08-1
KLT-08-2 KLT-08-3 KLT-08-4
APS 2011 15
KLT-09-01 KLT-12-1 KLT-12-2
KLT-15-1 KLT-15-2 KLT-16-1
APS 2011 16
KLT-16-2 KLT-17-1 KLT-17-2
KLT-20 KLT-22 KLT-24A
APS 2011 17
KLT-24C KLT-27 KLT-29-1
KLT-29-2 KLT-30 KLT-31-1
APS 2011 18
KLT-31-2 KLT-32 KLT-33A-1
KLT-33A-2 KLT-34-1 KLT-34-2
APS 2011 19
KLT-35 KLT-36A-1 KLT-36A-2
KLT-36A-3 KLT-36B-1 KLT-36B-2
APS 2011 20
KLT-36B-3 KLT-36C
KLT-38-1 KLT-38-2
APS 2011
21
KLT-39-2 KLT-40
Ginkgo Biloba 銀杏葉
APS 2011
22
QC-002 QC-003 QC-008
QC-009 QC-010 QC-012
APS 2010
23
QC-013 QC-014 QC-019
QC-020 QC-022 QC-023
APS 2010
24
QC-026 QC-027 QC-028
QC-032 QC-035A QC-035B
APS 2010
25
QC-036 QC-039 QC-044
QC-046 QC-047 QC-050
APS 2010
26
QC-051 QC-052 QC-053
QC-055 QC-057 QC-058
APS 2010
27
QC-061 QC-062 QC-063
QC-064 QC-065 QC-066
APS 2010
28
QC-067 QC-069 QC-070
QC-082 QC-083 QC-084
APS 2010
29
QC-086 QC-088 QC-089
QC-090 QC-093 QC-095
APS 2010
30
QC-096 QC-098 QC-099
QC-0100 QC-102 QC-102
APS 2010
31
QC-105 QC-106 QC-108
QC-110 QC-111 QC-112
APS 2010
32
All Intellectual Property Rights are Reserved &
Protected by APS Construction System
International Limited
33
中亞建築系統(國際)有限公司
APS Construction Systems (International) Ltd.
香港北角屈臣道4-6號海景大廈B座10樓1009室
Rm. 1009, 10/F., Block B, Sea View Estate,
4-6 Watson Rd, North Point, H K
Tel.: (852) 2979 0890 Fax.: (852) 2979 0499
Email: [email protected]
Website: www.apsconst.com
APS Stamp
Small Random Stone – Narrow Joint
Small Random Stone – Wide Joint
34
APS Stamp
Lychee Skin Texture Flame Granite Texture
100x100 Small Granite Tile Pattern
35
APS Stamp
Rectangular & Square Stone Tile Pattern
Ashlar Slate Tiles
36
APS Stamp
300x300 Stone Tiles
Plain
Texture
Staggered
37
APS Stamp
Various Sizes Stone
Tiles, 400x400, 500x500,
600x600 mm
38
APS Stamp
European Cobble Stone
Roman Slate
39
APS Stamp
Lisbon Mosaic Stone
Random Stone Tile
40
APS Stamp
Wave Fan
European Fan
41
APS Stamp
Verona Stone
Tactile Stamp for Blind
42
APS Stamp
Various Borders 43
APS Stamp
Herringbone Brick
Herringbone Tile
44
APS Stamp
Large
Herringbone
Block
Basketwave
Brick
Running Bond
Used Brick
Running Bond
Brick
45
APS Stamp
Large Random Stone
Santa Barbara Tile
46
APS Stamp
Garden Stone
Goose Egg Pebble
47
APS Stamp
Deep Texture
Marble Slate Cracked Granite
Lychee Texture Skin
Various Texture Skins
Coquina Shell Stone
Running Bond Slate
Shallow Slate
48
APS Stamp
Large Running Bond Stone
Various Width Wood Pattern
49
APS Stamp
Fossil Stone Tile
Lychee Stone Tile
50
APS Stamp
Spring Rain of West Lake
Medium Ashlar Slate
51
APS Stamp
Brick Pattern
3-D Cubes
52
APS Stamp
Wood Grains
Small Castle Stone
53
Waved Slate
APS Stamp
Big Goose Egg Stone
54
APS Stamp
Quarter Fan Flamed Stone & Square Flamed Stone
55
APS Stamp
Big Water Drops Fish Scale
Wood Grain
56
APS Stamp
Lotus
Fish
Flower Trumpet Shell
57
APS Thin Overlay Stamp Concrete58
APS Stamp Concrete Construction Tools59
APS Integral Chart 60
Method Statement for Installation of APS
Stamp Color Concrete Flooring System General
This method statement is offered as a guideline for the installation of APS Stamp Color Concrete Flooring System on suitable
substrate. APS reserves the total right to make any amendment from time to time. APS does not warrant any liabilities or loss due
to usage of this method statement by any person.
This method statement should be read in conjunction with the current product data sheet and MSDS of APS Color Stamp Concrete
Flooring System.
Subgrade Preparation
The subgrade should be well drained and have adequate and uniform load-bearing characteristics. To reduce cracking, it should be
graded so that the thickness of the concrete will be uniform. At the time of concreting, it must be moist, completely consolidated,
and free of ponding water. If necessary, the subgrade may be dampened with water in advance of concreting, but concrete should
not be placed over freestanding water or over soft, muddy of frozen ground.
Formwork Erection
Erect edge formwork with top edge level to match the finished concrete level. Note the finished concrete level must match
the designed fall gradient.
Recommended thickness for driveway is 100 – 150mm, depending on type of traffic loading.
Recommended thickness for pedestrian walkway is 75- 100mm.
Plan pattern layout, coordinate slab expansion joint, and control joint dimension & locations with stamping pattern
dimensions where necessary.
Expansion Joint & Control Joint
The Expansion Joint and Control Joint have to be complied with design drawings and specifications.
Recommended Expansion and Control Joint distance to be less than 4 M.
Steel Mesh Reinforcement
Place approved steel mesh reinforcement with the approved concrete cover and overlapping.
Concrete Mix Design
1. Concrete Design is ____________MPa compressive strength, aggregate size is 10mm max.
2. Cement Content is ________ Kg/m3.
3. Slump: 100mm
4. Do not use excessive super plasticizers.
5. Do not use calcium chloride or non-chloride accelerators.
61
Method Statement for Installation of APS
Stamp Color Concrete Flooring System
6. Approved APS Integral Color: ____________________, ___% of cement content, never use integral color
more than 10% of cement content.
APS Stamp Color Concrete Installation
1. Ready-mixed concrete supplier for the APS Stamp Color Concrete project has to be maintained
from one source from start to completion.
2. Upon concrete truck arrives site, dose the right amount of integral color pigment into concrete
truck, quickly rotate the drum for 15 minutes.
3. Pour / place well-mixed APS Integral Color concrete into place with pump or wheel barrow.
4. Vibrate concrete as normal standard practice.
5. Concrete shall be poured and finished up to specified level with wood float or screed.
6. Remove the breeding water or wait until the breeding water dry out to a suitable level.
7. Apply 50% of APS Color Hardener at specified application rate (ie. 3kg/m2 – 5kg/m2
depending on chosen color) to freshly floated concrete surface.
8. Broadcast and distribute APS Color Hardener evenly by hand or tools.
9. As soon as APS Color Hardener material has absorbed moisture, which will be indicated by
uniform darkening of surface, use concrete float to smooth concrete surface a second time, just
enough to bring moisture from base slab through color hardener to the surface.
10. Immediately following second floating, apply remaining 50% of specified application rate of
APS Color Hardener. Broadcast in opposite direction of first application for a more uniform
coverage.
11. Do not add water to the surface.
12. Wait until a suitable drying condition, use a steel trowel to trowel the color hardener surface to
an even smooth surface.
62
Method Statement for Installation of APS
Stamp Color Concrete Flooring System
13. Wait until the concrete is set up to a condition to support a person’s weight, or use a finger to press
the concrete and if it does not stick to the finger, then it is about time for stamping procedures.
14. Before stamping, broadcast approved color powder release as stamp concrete release agent at
approximate rate of 0.15kg/m2.
15 Begin imprinting and stamping operations by using stamp molds with planned direction until
job completed.
16. After the stamped concrete is dry and cured for 24 hours, use a chisel to remove the double line
appearance.
Concrete Curing
Allow concrete slab to thoroughly cure with natural curing method, or by any approved methods. Do not use chemical curing
compound.
Saw Cutting for Control Joint
After stamp concrete curing for 2 – 7 days, proceed the saw cutting to form control joints if necessary according to design drawing.
The depth of saw cutting should be aimed at 2/3 of the depth of concrete.
Wash off the Release Agent
Wash off the release agent to the condition of approved mock up. Be cautious that too much washing off will lead to less antique
effect and too less washing off would create a strong antique effect on the finish.
Sealing
Rinse and wash off the release agent with some left over to form antiquing effect as according to approved mock up. Let it dry for
24 hours, apply 2 coats of APS Stamp Concrete Sealer.
- END -
63