Technische InformationRINGSDORFF® Spezialgraphit-Marken für die Funkenerosion
Physikalische Eigenschaften
R 8340
R 8500X
R 8500
R 8510
R 8710
Wirtschaftliche Schruppmarke
Universalwerkstoff für den Formenbau
Verschleißfester Feinkorngraphit für hohe Anforderungen
0Feinstschlichtwerkstoff zur Erzielung bester
Oberflächengüten, bei vergleichsweise hohen Abtragsraten füreine Feinstschlichtmarke
R 8650
Schlichtwerkstoff für besonders hohe DetailwiedergabeSchrupp- und Vorschlichtmarke
100
μm
Broad Base. Best Solutions.
Es handelt sich um mittlere Werte.
R 8340
1,72
15
15
12
2,0
15
80
HR 10/100
45
10,5
12
90
2,9
0,02
R 8500X
1,75
14
12
2,0
15
80
HR 5/100
43
10
15
80
3,8
0,02
R 8500
1,77
13
10
1,5
10
70
HR 5/100
50
10,5
14
80
3,9
0,02
R 8510
1,83
10
10
8
1,5
4
95
HR 5/100
60
11,5
13
100
4,0
0,02
R8650
1,84
10
7
6
0,8
3
95
HR 5/100
65
12,5
14
90
3,9
0,02
R 8710
1,88
10
3
3
0,6
1
110
HR 5/100
85
13,5
13
100
4,7
0,02
Dichte
Porosität (offen)
Mittlere Korngröße
Korngröße optisch vermessen
Mittlere Porengröße
Permeabilität
Härte Rochwell B
Biegefestigkeit
Elastizitätsmodul
Elektrischer Widerstand
Wärmeleitfähigkeit
Wärmeausdehnung
(20 – 200 °C)
Aschwert
g/cm3
Vol.-%
µm
µm
µm
x 10-2 cm2/sec
MPa
GPa
µΩm
W m-1 K-1
x 10-6 K-1
max. %
® eingetragene Marke von Unternehmen der SGL Group 11 2010/1 4NÄ Printed in Germany
Diese Angaben entsprechen dem aktuellen Stand unserer Produktkenntnisse und sollen allgemein über unsere Produkte und deren Anwendungsmöglichkeiten infor-mieren. Im Hinblick auf die Unterschiedlichkeit der möglichen Anwendungen sind die Angaben nur als allgemeine Informationen zu verstehen, die keine bestimmtenEigenschaften der Produkte für jeden konkreten Einsatzfall garantieren. Im Auftragsfalle sind daher die für den Anwendungsfall erforderlichen Eigenschaften konkretbei uns abzufragen. Unser technischer Service wird auf Anfrage dann umgehend ein Eigenschaftsprofil für den konkreten Anwendungszweck mitteilen.
Graphite Specialties SGL CARBON GmbHPhone +49 228 841-577 [email protected]
www.sglgroup.com
Abmessungsprogrammvon RINGSDORFF® Isographite
1550 x 410 x 2001230 x 500 x 400610 x 500 x 400
1230 x 500 x 400610 x 500 x 400
1230 x 480 x 260610 x 480 x 260
610 x 390 x 1901230 x 1030 x 3301230 x 500 x 400610 x 500 x 400
Verschnittfreie Zuschnitte aus o.g. Abmessungen erfolgen ohne Mehrkosten.Bei den angegebenen Maßen handelt es sich um Mindestmaße in mm.
Vorbereitete Eelektrodenrohlinge für diverseSpann systeme auf Anfrage.
R 8340 R 8500XR 8500
R 8510 R 8650 R 8710
Ø 150 x 1230Ø 180 x 1230Ø 200 x 1230Ø 225 x 1230Ø 250 x 1230Ø 280 x 1230Ø 320 x 1230Ø 350 x 1230Ø 380 x 1230Ø 420 x 1230
Abmessungsprogramm
Technische InformationRINGSDORFF® Specialty Graphite Grades for EDM
Physical Properties
R 8340
R 8500X
R 8500
R 8510
R 8710
Efficient grade for roughing
Universal grade for toolmakers
Wear resistant fine grain graphite for demanding applications
Premium finishing grade to perform high quality EDM tasks with high removal rates
R 8650
Finishing grade for highest accuracyGrade for roughing and prefinishing
Broad Base. Best Solutions.
Average values.
R 8340
1.72
15
15
12
2.0
15
80
HR 10/100
45
10.5
12
90
2.9
0.02
R 8500X
1.75
14
12
2.0
15
80
HR 5/100
43
10
15
80
3.8
0.02
R 8500
1.77
13
10
1.5
10
70
HR 5/100
50
10.5
14
80
3.9
0.02
R 8510
1.83
10
10
8
1.5
4
95
HR 5/100
60
11.5
13
100
4.0
0.02
R8650
1.84
10
7
6
0.8
3
95
HR 5/100
65
12.5
14
90
3.9
0.02
R 8710
1.88
10
3
3
0.6
1
110
HR 5/100
85
13.5
13
100
4.7
0.02
Density
Open Porosity
Average Grain Size
Grain Size Measured Optical
Average Pore Size
Permeability
Rockwell Hardness
Flexural Strength
Young s Modulus
Electrical Resistivity
Thermal Conductivity
Thermal Exp.
(293.15 - 473.15 K)
Ash Value
g/cm3
Vol.-%
µm
µm
µm
x 10-2 cm2/sec
MPa
GPa
µΩm
W m-1 K-1
x 10-6 K-1
max. %
0 100
μm
® registered trademark of SGL Group companies 11 2010/1 3NÄ Printed in Germany
This document has been prepared according to the best current knowledge and is intended to provide general information about our products and their use. In view of the wide variety of possible applications, the above data should be regarded as general information and are no guarantee of certain features of our products in a given case. If youfavour us with your order, please ask for information regarding the features needed for the proposed application. Our Technical Service will furnish a feature profile for suchapplication without undue delay.
Graphite Sepcialties SGL CARBON GmbHPhone +49 228 841-577 [email protected]
www.sglgroup.com
Dimension List ofEDM RINGSDORFF® Iso-Graphites
We do not charge for cutting standard blocks if no off-cut material is generated.The dimensions shown above are minimum sizes in mm.
Prepared electrode blanks for various clamping systems on request.
Dimension List
1550 x 410 x 2001230 x 500 x 400610 x 500 x 400
1230 x 500 x 400610 x 500 x 400
1230 x 480 x 260610 x 480 x 260
610 x 390 x 1901230 x 1030 x 3301230 x 500 x 400610 x 500 x 400
R 8340 R 8500XR 8500
R 8510 R 8650 R 8710
Ø 150 x 1230Ø 180 x 1230Ø 200 x 1230Ø 225 x 1230Ø 250 x 1230Ø 280 x 1230Ø 320 x 1230Ø 350 x 1230Ø 380 x 1230Ø 420 x 1230
Top Related