For heavy duty professional work For the toughest environments needing high capacity. The wide working range together with the possibility for carbon arc gouging makes it possible to perform a large variety of work in environments where it is difficult or impossible to connect to the mains supply. KHM 595 PS is equipped with a powerful and efficient, water-cooled Perkins diesel engine with battery and electric start.

Welding - Coated electrodes - CCCoated electrodes up to 8 mm can be welded. The low, 10 A min current allows welding with very small electrodes. Using the adjustable Arc force control optimizes welding of cellullosic electrodes. Special gouging outlets give optimal performance.

Welding – MIG/MAG - CVThe Digital control of the welding current give KHM 595 excellent performance on MIG/MAG welding. It can be used with MobileFeed or with an optional connection kit the unit can be used with Origo™ Feed 304 M13 or Origo™ Feed 484 M13 for MIG/MAG welding.

Auxiliary powerElectricity is often needed to carry out the complete job. Drilling, grinding, drying electrodes and lighting are a few examples. On KHM 595 PS you can use up 30kVA three phase 400V, or 15 KVA single phase 230 V power even when welding. A voltmeter shows the actual supply voltage. The units are equipped with earth fault protection for added safety.

FeaturesSeparate gouging outlets, hour meter, over-speed protection, battery charge/low fuel/oil pressure indicators indicator, thermal load, arc force, voltmeter, lifting eyelet and earth fault protection.

TransportThe units are delivered as stationary. For transport, within the work site, there is optional site tow equipment available. Both units have central lifting eyelet.

Applications

KHM 595 PSEngine driven welding /electric power units for the toughest, professional, heavy-duty repair, maintenance and assembly work

XA00131220

• Digital Control of welding current

• Multi process welder: - SMAW: Shielded Metal Arc Welding (Stick) - GMAW:Gas Metal Arc Welding (MIG) - FCAW: Flux Cored Arc Welding (Flux Cored) - GTAW: Gas Tungsten Arc Welding (TIG scratch start)

• Low welding current range (50%) in C.C. mode

• Auxiliary power (up to 30kVA) available during welding

• Ground Fault Interrupter protection

• Large (65 l) fuel tank for up to 16 hours operation

• VRD (Voltage Rediction Device)

• Perkins, water cooled diesel engine (1500 rpm)

• Engine protection (oil pressure/temperature/over speed)

• General fabrication and civil construction• Repair and maintenance• Power generation• Pipelines

KHM 595 PS

Unrivalled service and support Our commitment and ability to deliver the expected service and support starts immediately after the order is confirmed. We endeavour to offer our customers an After Sales service, which is second to non. A strong and skilful service organisation is prepared to offer service and maintenance, calibration, validation and upgrading of equipment and software.

The service organisation will offer standardised solutions for the reconditioning or modification of existing products.

Spare and wear parts are manufactured according to ESAB’s quality plan. Exchange Printed Circuit Board (PCB), exchange modules and components are available for all our products in order to reduce cost and downtime to an absolute minimum. ESAB is continuously upgrading authorised service partners for local service support. Customers who have their own service and maintenance personnel will always be offered a service- training package as part of a total ESAB offering. However, product and process training for end-users will form an additional part of the ESAB offering. Always ask your ESAB sales representative or distributor for a complete ESAB solution.

Ordering information

Technical data

KHM 595 PSConstant Current (C.C) –SMAW (Stick)/ GTAW (TIG)Current range, continuous, A 10-595 Open circuit voltage, V 60Duty cycleMax welding output at 60%, A 550Max welding output at 100%, A 500

Constant Voltage (C.V) –GMAW (MIG/MAG)/ FCAW (Flux Cored)Voltage range, V 16-44Duty cycleMax welding output at 60%, A 550Max welding output at 100%, A 500

A.C. generationTree- Phase, generation, kVA/V 30/400Single- Phase, generation, kVA/V 15/230 Duty cycle, - 100%Insulating class, - H

Engine Type Perkins 1103C - 33G3 Output *, kW(hp) 30.4 (40.7)Speed, rpm 1500 Displacement, cm3 3300 Cylinders 3Fuel consumptions, g/kWh 242

* Maximum output (not overloadable) according to ISO 3046/1

General specifikationsTank capacity, ltr 65 Running time (at 60%), h 16Protection IP 23Dimensions* Lxwxh, mm 2000x850x1130Weight (empty tank), kg 980Guaranteed acoustic power, LWA/dB(A)-7m 96/71

*Dimensions end weight are inclusive of all parts without wheels and towbar

KHM 595 PS (50Hz) 0794 003 883

Accessories2 wheel site tow 0794 018 880PHG1, remote control 20m 0794 008 881Earthing kit 0794 017 880V/A-meter kit 0794 000 160Connector kit for Feed M13, 19 to 10-pole 0740 741 881

Delivery content: Machine complete with engine oil, coolant and charged battery (maintenance free).

Albatross 3000 welding helmet, both for welding and grinding.The welding glass folds up and the inner glass protects you when grinding.

Quality accessories for the quality welderESAB offers a wide range of accessories. The complete range, along with product information, is available at our local web-sites, look at www.esab.com or contact your local ESAB dealer.

ESAB ABBox 8004SE-402 77 GÖTEBORG SWEDENPhone: +46 31 50 90 00 Fax +46 31 22 04 49E-mail: info@esab.se

www.esab.com

2009

-04

-08

/ E

SA

B r

ese

rve

sth

e r

igh

tto

alte

r sp

eci

fica

tions

with

ou

tprio

r no

tice