WorkFit-A, Single LCD Mount, LD - Ergotron · WorkFit-A, Single LCD Mount, LD User's Guide -...
Transcript of WorkFit-A, Single LCD Mount, LD - Ergotron · WorkFit-A, Single LCD Mount, LD User's Guide -...
888-45-298-W-02 rev.L • 12/15 1 of 16
WorkFit-A, Single LCD Mount, LD
User's Guide - EnglishGuía del usuario - EspañolManuel de l’utilisateur - FrançaisGebruikersgids - DeutschBenutzerhandbuch - NederlandsGuida per l’utente - ItalianoAnvändarhandbok - svenskaユーザーガイド : 日本語用户指南 : 汉语
IncludesConstant Force™Technology
ENGLISH
ASSEMBLY INSTRUCTIONS
For the latest User Installation Guide please visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.comFor Service visit: www.ergotron.comFor Warranty visit: www.ergotron.com/warranty
Learn more about ergonomic computer use at:
www.computingcomfort.org
Set Your Workstation to Work For YOU!
Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists fl at. Distance Position screen an arm's length from face—at least 20” (508mm). Position keyboard close enough to create a 90˚ angle in elbow. Angle Tilt screen to eliminate glare. Tilt the keyboard back 10° so that your wrists remain fl at.
To Reduce FatigueBreathe - Breathe deeply through your nose.Blink - Blink often to avoid dry eyes.Break • 2 to 3 minutes every 20 minutes• 15 to 20 minutes every 2 hours.
888-45-298-W-02 rev.L • 12/152 of 16
5 - 15 lbs(2.3-6.8 kg)
A
< 5 lbs (2.27 kg)
< 2 lbs (0.9 kg)
B
C
A+B+C < 20 lbs (9.1 kg)
0.78"-2.56" (20-65mm)
0.78"-2.56" (20-65mm)
0.5"-2.5" (13-64mm)
Arm lowers along an arc. Pull Arm toward you as
you lower from the highest position.
827-975
ENGL
ISH
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product
and equipment.
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Adjust the height of your desk (or chair and footrest) to allow the keyboard to lower to your sitting elbow height for ergonomic computing.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these
instructions may result in equipment damage or personal injury.
Arm lowers along an arc. Pull arm towards you as you lower from the highest
position.
CAUTION! Tipping Hazard. Support the stand until the clamp is securely
tightened. Failure to follow these instructions may result in the stand tipping over
causing possible equipment damages and or personal injury.
Safety
Caution:
DO NOT route cables on top of arm. Failure to follow these instructions may result in equipment damage
and/or personal injury.
888-45-298-W-02 rev.L • 12/15 3 of 16
360˚
20"(508 mm)
20˚
10˚
5"(127 mm)
85˚
A B C D E F
1
2
3
4
5
6
7
1x 1x
1x 4x
2x
M4 x 10mm
M4 x 10mm
4x
8x
1x
1x
1x
M3 x 6mm
M5 x 8mm
1/4"
1/4”1x8mm
1x
4 mm8x
1x
1x
M4x16mm
1x
1x
1x1x 2x
2xM6 x 45mm
1x
1x
M5 x 35mm
ENGLISH
888-45-298-W-02 rev.L • 12/154 of 16
1
12"
(300 mm)
18"
(460 mm)
16"
(410 mm)
10"
(260 mm)
12.75"
(320 mm)
12.75"
(320 mm)
12.75"
(320 mm)
12.75"
(320 mm)
Top View
Top View
12.75"
(320 mm)9.5"
(250 mm)
9.5"
(250 mm)9.5" (250 mm)
9.5"
(250 mm)
10"
(260 mm)
16"
(410 mm)
12.75"
(320 mm)
1 2
3 4
55
6
6
ENGL
ISH
With Expanded Arm Extension With Expanded Arm Extension
Arm Extension and Desk Size:
The keyboard tray is designed to extend over the edge of your desk. You can expand the extension of the arm if
you need to based on your desk size. To determine if you need to expand your arm extension, refer to the 4 desk
dimensions below:
CLAMP
CLAMP
CLAMP
GROMMET HOLE
GROMMET HOLE
GROMMET HOLE
To expand the arm extension, follow instructions on
next page.
Grommet hole can
be located anywhere
along this arch.
Grommet hole can
be located anywhere
along this arch.
To expand the arm extension, follow instructions on next page.
CAUTION: Base must be completely on desk surface.
Failure to follow these instructions may result in
equipment damage or personal injury.
888-45-298-W-02 rev.L • 12/15 5 of 16
4 mm
d1 d2 d3
b c da180˚ 180˚
ENGLISH
How to expand the arm extension.
Remove the 4 screws at the
base using the provided 4mm
hex wrench.
Flip the base around (turn
180 degrees.
Re-insert the 4 screws and tighten
with the 4mm hex wrench.
888-45-298-W-02 rev.L • 12/156 of 16
1/4"
1/4”
8mm
2 0.78"-1.78" (20-45mm) 1.70"-2.56" (43-65mm) 4 mm
7
8
ENGL
ISH
Warning: Because mounting surface materials can vary widely, it is imperative that you make
sure mounting surface is strong enough to handle mounted product and equipment.
Mount arm to desk.
Tighten the bolts with the provided 8 mm wrench.
Clamp confi gurations for diff erent desk thickness
OPTIONAL GROMMET HOLE MOUNT
- Follow these instructions if you want to change your clamp to a grommet
hole mount.
CAUTION! Tipping Hazard. Support the stand until
the clamp is securely tightened. Failure to follow
these instructions may result in the stand tipping
over causing possible equipment damages and or
personal injury.
888-45-298-W-02 rev.L • 12/15 7 of 16
a
c
b
d
4 mm
1x1x
1x
1x
0.78"-2.56"
(20-65mm)
0.5"-2.5"
(13-64mm)
ENGLISH
CAUTION: Bolt must be centered
in hole.
Remove clamp bracket screws with
4mm hex wrench.
Insert provided bolt into provided grommet
plate. Attach grommet plate with 4 mm hex
wrench and screws removed in step b.
Remove clamp plate screws with
4mm hex wrench. Retain screws.
Position arm with attached grommet plate over
grommet hole (make sure bolt is centered in
hole). Thread grommet bracket and wing nut
onto bolt and tighten.
OPTIONAL GROMMET HOLE MOUNT
- Follow these instructions if you want to change your clamp to a grommet
hole mount.
888-45-298-W-02 rev.L • 12/158 of 16
4 mm2xM6 x 45mm
3
2x
a
b
cM5 x 35mm
ENGL
ISH
WARNING!
Screws must be tightened to keep
product secure. Failure to follow these
instructions will create an unstable
situation and may result in equipment
damage or personal injury.
888-45-298-W-02 rev.L • 12/15 9 of 16
41xa b
c2x
M4x16mm
ENGLISH
888-45-298-W-02 rev.L • 12/1510 of 16
5 a
b 1xM5 x 8mm4 mm
60°
M3 x 6mm1x
M4 x 10mm
M4 x 10mm
4x
4x
ENGL
ISH
888-45-298-W-02 rev.L • 12/15 11 of 16
1x
4x
8 1x
M4 x 10mm
4x
7 a
b
c
ENGLISH
888-45-298-W-02 rev.L • 12/1512 of 16
9
8x
1x
ENGL
ISH
NOTE: Leave enough slack in cable to allow full range of motion.
Caution:
To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to
follow these instructions may result in equipment damage or personal injury.
Caution:
DO NOT route cables on top of arm.
Failure to follow these instructions
may result in equipment damage
and/or personal injury.
888-45-298-W-02 rev.L • 12/15 13 of 16
10
1/4"
1/4”
8mm
1
2
3
a
Adjustment Step
ENGLISH
Increase Lift StrengthIf the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift StrengthIf the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
888-45-298-W-02 rev.L • 12/1514 of 16
b
c
1/4"1/4”
8mm
ENGL
ISH
Increase Lift StrengthIf the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift StrengthIf the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
Increase Lift StrengthIf the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift StrengthIf the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
888-45-298-W-02 rev.L • 12/15 15 of 16
d 1/4"1/4”
8mm
e 1/4"1/4”
8mm
f4 mm
ENGLISH
Increase FrictionIf this product moves too easily from side-to-side, then you'll need to increase friction:
Decrease FrictionIf this product is too diffi cult to move from side-to-side, then you'll need to decrease friction:
Increase FrictionIf this product moves too easily, then you'll need to increase friction:
Decrease FrictionIf this product is too diffi cult to move, then you'll need to decrease friction:
Increase FrictionIf this product moves too easily, then you'll need to increase friction:
Decrease FrictionIf this product is too diffi cult to move, then you'll need to decrease friction:
888-45-298-W-02 rev.L • 12/1516 of 16
f
4 mm
1
2
3
ENGL
ISH
Loosen these two screws.
Loosen or tighten this bolt to adjust tilt to desired angle.
Tighten to tilt up.
Loosen to tilt down.
After desired tilt is achieved, retighten these
two screws to secure.
WARNING!
Screws must be tightened to keep product secure.
Failure to follow these instructions will create an
unstable situation and may result in equipment
damage or personal injury.
Angle Setting Adjustment