1/4

Will Mold Cleaning Remove Smell?mmihomeimprovement.com/2021/04/27/will-mold-cleaning-remove-smell

Did you sense any musty smell when you turn on your heating and cooling system? It

might be an indication of mold growth in your unit. Mold is not only unpleasant but very

hazardous to health. Your indoor air quality will be destroyed. If you try DIY cleaning

methods or call an expert for the job, you might be concerned about one thing. Will

mold cleaning remove the smell?

How to Get Rid of Mold?

You should know that the leading cause of odor in your HVAC system is mildew. It usually

grows in damp areas. And your AC system is usually damp due to the condensation

process. While this can be a severe problem, the great news is that there is a simple way to

clean it and remove unpleasant odors.

Before you start mold cleaning, just turn off the system and wear a protection kit. Here

are a few simple tips to remove mold odor from your HVAC unit:

2/4

Cleaning Coils and Spraying Fungistat

You must know that coils are a significant part of the system. It is the place where the air

cools down. Ignoring the cleaning of coils may cause excessive moisture and mold

development. So, you should regularly clean the coil and spray them with Fungistat to

avoid mold growth. It will remove the foul odor.

Examine Condensate Pumps and Clean it with Biocide

While cleaning the coils, you should also examine the condensate pump and pan. If water

accumulates in the pan, it can lead to mold and bacterial growth. If you ignore the

cleaning, your system might break down. Using a biocide and Fungistat can help remove

the bad smell.

Ductwork Cleaning and Treating it with Fungistat

When cleaning your system, you must check your ductwork. If there is mold growth, you

should clean it with an EPA-approved disinfectant and then treat it with Fungistat.

Inspect Returns and Clean Debris

Returns are part of the HVAC system, which draws air from within your home. So, you

must check the returns for mold development. If mold is present, call Mold Air Duct

Cleaning in Alpharetta to identify the reason for too much humidity in the system. If

there is any leakage, they will immediately treat it and save your system from significant

damages. Make sure that they clean it with an EPA-approved disinfectant and apply

Fungistat.

Spray an Odor Eliminator in Your System

After you are done with system cleaning, spray it with a FreshDuct odor eliminator. You

should specifically spray the coils, drain pans, ductwork, and air returns. Using this will

give you incredible results.

DIY Odor Control in HVAC

You can dust baking soda in your air ducts to get rid of the foul odor. When baking soda

comes in contact with invasive air particles, it will remove them. So, you should dust the

soda on the maximum surface area.

Duct Filter Pad

You should install duct filter pads in your outlets as they can effectively control the

unpleasant odor caused due to mold. You can easily find these hypoallergenic filter pads

in any home store nearby. These are available in many sizes and easily fit vertical and

horizontal ducts.

To install a duct filter pad, you need to unscrew your vent covers and insert the pad into

the grill. Fix the cover again and allow the pad to filter all harmful particles and smells.

3/4

Hence, following these steps will purify indoor air and make it fragrant. Using chemicals

that are not approved by EPA will wipe out any health danger.

When Should You Hire a Professional for HVAC Cleaning?

If the tips mentioned above and tricks do not show desired results, you should try a

thorough cleaning of your air ducts. Suppose you observe that the smell’s source is pest

infestation instead of mold. In that case, you should immediately call HVAC Cleaning

in Alpharetta for professional assistance.

You must take a professional’s help for HVAC cleaning if:

You observe visible mold growth in the hard duct surfaces or other HVAC

components.

Pests or vermin are living in the ducts. These can be either dead or alive. You must

know that it is an alarming issue as it can lead to severe health conditions.

Your system is clogged with dust and debris. Excessive dust coming out from the

system indicates air duct blockage.

If you cannot access various segments of your HVAC unit or air ducts.

A ductwork leakage that might be indicated by a water flow needs a professional to

repair the problem.

You will have to see the type of HVAC ductwork to determine the best-fit cleaning

method. Hence, it is essential to first know the type of material your ductwork. Generally,

the ductworks are made of sheet metal, fiber-glass, and fiberboard. Some flexible

ductworks are also manufactured of wire coils and insulated with plastic. Moreover, your

ductwork material can be a combination of all the materials. So, it is crucial to identify the

ductwork material before choosing the cleaning method. A professional might be able to

decide better.

How to Find the Best HVAC Services?

4/4

Are you thinking of hiring an expert for HVAC inspection and maintenance? You must

conduct thorough research before you hire someone. The best approach is to shortlist

credible service providers and contact them. You should discuss rates, service time,

certifications, years of service, qualifications, equipment, and chemicals they use.

Consider at least three companies while researching. Asking for referrals is another good

way.

Consider a few essential things before you make a decision:

Avoid companies that make sweeping claims about their services.

Never hire a company that recommends regular cleaning as part of good HVAC

maintenance.

Some companies may tell you that they are certified by EPA. You must know that

EPA is not concerned with duct cleaning standards or service providers.

A ductwork cleaning service under $100 might not include all ducts of your home. A

standard company demands at least $150 for all ductworks.

Always request for before and after pictures of your system.

Ask for state licenses if you doubt the company’s reputation.

Never allow companies to use sealants unless no other technique is possible.