Vlt Hvac Basic Drive Fc 101
description
Transcript of Vlt Hvac Basic Drive Fc 101
MAKING MODERN LIVING POSSIBLE
QQuick GuideVLT® HVAC Basic Drive FC 101
www.danfoss.com/drives
*MG18A402*132R0078 MG18A402 Rev. 2012-03-23
Downloaded from www.Manualslib.com manuals search engine
Contents
1 Quick Guide 2
1.1 Safety 2
1.1.1 Warnings 2
1.1.2 Safety Instructions 2
1.2 Introduction 3
1.2.1 Available Literature 3
1.2.2 Approvals 3
1.2.3 IT Mains 3
1.2.4 Avoid Unintended Start 4
1.2.5 Disposal Instruction 4
1.3 Installation 4
1.3.1 Before Starting Repair Work 4
1.3.2 Side-by-Side Installation 4
1.3.3 Dimensions 5
1.3.4 Electrical Installation in General 6
1.3.5 Connecting to Mains and Motor 7
1.3.6 Fuses 13
1.3.7 EMC-Correct Electrical Installation 15
1.3.8 Control Terminals 17
1.3.9 Electrical Overview 18
1.4 Programming 19
1.4.1 Programming with the Local Control Panel (LCP) 19
1.4.3 The Start-up Wizard for Open Loop Applications 20
1.5.1 Main menu structure 30
1.6 Warnings and Alarms 32
1.7 General Specifications 34
1.7.1 Mains Supply 3x200-240 V AC 34
1.7.2 Mains Supply 3x380-480 V AC 35
1.7.3 Mains Supply 3x380-480 V AC 37
1.7.4 Mains Supply 3x525-600 V AC 39
1.8 Special Conditions 43
1.8.1 Derating for Ambient Temperature and Switching Frequency 43
1.8.2 Derating for Low Air Pressure 43
1.9 Options for VLT® HVAC Basic Drive FC 101 43
1.10 MCT 10 Support 43
Contents VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 1
Downloaded from www.Manualslib.com manuals search engine
1 Quick Guide
1.1 Safety
1.1.1 Warnings
WARNINGHigh Voltage WarningThe voltage of the frequency converter is dangerouswhenever it is connected to mains. Incorrect installation ofthe motor or frequency converter may cause damage tothe equipment, serious injury or death. Consequently, it isessential to comply with the instructions in this manual aswell as local and national rules and safety regulations.
WARNINGDISCHARGE TIME!Frequency converters contain DC-link capacitors that canremain charged even when the frequency converter is notpowered. To avoid electrical hazards, disconnect AC mains,any permanent magnet type motors, and any remote DC-link power supplies, including battery backups, UPS andDC-link connections to other frequency converters. Wait forthe capacitors to fully discharge before performing anyservice or repair work. The amount of wait time is listed inthe Discharge Time table. Failure to wait the specified timeafter power has been removed before doing service orrepair could result in death or serious injury.
Voltage [V] Power range [kW] Minimum waiting time[min]
3x200 0.25–3.7 4
3x200 5.5–11 15
3x400 0.37–7.5 4
3x400 11–90 15
3x600 2.2–7.5 4
3x600 11–90 15
Table 1.1 Discharge Time
CAUTIONLeakage Current:The earth leakage current from the frequency converterexceeds 3.5 mA. According to IEC 61800-5-1 a reinforcedProtective Earth connection must be ensured with a min.10 mm² Cu or an additional PE wire - with the same cablecross section as the Mains wiring - must be terminatedseparately.Residual Current Device:This product can cause a DC current in the protectiveconductor. Where a residual current device (RCD) is usedfor extra protection, only an RCD of Type B (time delayed)shall be used on the supply side of this product. See alsoDanfoss Application Note on RCD, MN90G.Protective earthing of the frequency converter and the useof RCDs must always follow national and local regulations.
Motor thermal protection:Motor overload protection is possible by setting Parameter1-90 Motor thermal protection to the value ElectronicThermal Relay (ETR) trip.
WARNINGInstallation at high altitudesFor altitudes above 2 km, contact Danfoss regarding PELV.
1.1.2 Safety Instructions
• Make sure the frequency converter is properlyconnected to earth.
• Do not remove mains connections, motorconnections or other power connections whilethe frequency converter is connected to power.
• Protect users against supply voltage.
• Protect the motor against overloading accordingto national and local regulations.
• The earth leakage current exceeds 3.5 mA.
• The [Off/Reset] key is not a safety switch. It doesnot disconnect the frequency converter frommains.
Quick Guide VLT® HVAC Basic Drive Quick Guide
2 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.2 Introduction
1.2.1 Available Literature
This Quick Guide contains the basic information necessaryfor installing and running the frequency converter. If moreinformation is needed, literature can be found on theenclosed cd or downloaded from:www.danfoss.com/BusinessAreas/DrivesSolutions/Documen-tations/Technical+Documentation.htm
1.2.2 Approvals
Table 1.2
IP54 enclosure frequency converterdo not have UL approvals.
Table 1.3
1.2.3 IT Mains
CAUTIONIT MainsInstallation on isolated mains source, that is, IT mains.Max. supply voltage allowed when connected to mains:440 V (3x380-480 V units).
On IP20 200-240 V 0.25-11 kW and 380-480 V IP20 0.37-22kW, open the RFI switch by removing the screw on theside of the frequency converter when at IT grid.
130B
B612
.10
1
Illustration 1.1 IP20 200-240 V 0.25-11 kW, IP20 0.37-22 kW380-480 V.
1 EMC screw
Table 1.4
130B
C25
1.10
Illustration 1.2 IP54 400 V 0.75-18.5 kW
1 EMC screw
Table 1.5
On all units, set to [Off] when operating in IT mains.
CAUTIONIf reinserted, only use M3x12 screw.
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 3
1 1
Downloaded from www.Manualslib.com manuals search engine
1.2.4 Avoid Unintended Start
While the frequency converter is connected to mains, themotor can be started/stopped using digital commands, buscommands, references or via the LCP.
• Disconnect the frequency converter from mainswhenever personal safety considerations make itnecessary to avoid unintended start of anymotors.
• To avoid unintended start, always press [Off/Reset] before changing parameters.
1.2.5 Disposal Instruction
Equipment containing electrical componentsmust not be disposed of together with domesticwaste.It must be separately collected with electricaland electronic waste according to local andcurrently valid legislation.
Table 1.6
1.3 Installation
1.3.1 Before Starting Repair Work
1. Disconnect FC 101 from mains (and external DCsupply, if present).
2. Wait as stated in Table 1.1 for discharge of theDC-link.
3. Remove motor cable.
1.3.2 Side-by-Side Installation
The frequency converter can be mounted side-by-side andrequires the clearance above and below for cooling.
Power [kW] Clearance above/below [mm/inch]
Frame IP class 3x200-240 V 3x380-480 V 3x525-600 V
H1 IP20 0.25-1.5 0.37-1.5 100/4
H2 IP20 2.2 2.2-4 100/4
H3 IP20 3.7 5.5-7.5 100/4
H4 IP20 5.5-7.5 11-15 100/4
H5 IP20 11 18.5-22 100/4
H6 IP20 15-18.5 30-45 18.5-30 200/7.9
H7 IP20 22-30 55-75 37-55 200/7.9
H8 IP20 37-45 90 75-90 225/8.9
H9 IP20 2.2-7.5 100/4
H10 IP20 11-15 200/7.9
Table 1.7
NOTEWith IP21/Nema Type1 option kit mounted, a distance of50 mm between the units is required.
Quick Guide VLT® HVAC Basic Drive Quick Guide
4 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.3.3 Dimensions
Aa
bB
C
0 D
130B
B614
.10
e
fa
d
e
130B
C205
.10
e
fa
e
130B
C246
.10
Table 1.8
Enclosure Power [kW] Height [mm] Width [mm] Depth[mm]
Mounting hole[mm]
Max.Weig
ht
Frame IP Class 3x200-240 V 3x380-480 V 3x525-600 V A "A incl De-coupling
Plate"
a B b C d e f kg
H1 IP20 0.25-1.5 0.37-1.5 195 273 183 75 56 168 9 4.5 5.3 2.1
H2 IP20 2.2 2.2-4.0 227 303 212 90 65 190 11 5.5 7.4 3.4
H3 IP20 3.7 5.5-7.5 255 329 240 100 74 206 11 5.5 8.1 4.5
H4 IP20 5.5-7.5 11-15 296 359 275 135 105 241 12.6 7 8.4 7.9
H5 IP20 11 18.5-22 334 402 314 150 120 255 12.6 7 8.5 9.5
H6 IP20 15-18.5 30-45 18.5-30 518 595/635(45 kW)
495 239 200 242 - 8.5 15 24.5
H7 IP20 22-30 55-75 37-55 550 630/690(75 kW)
521 313 270 335 - 8.5 17 36
H8 IP20 37-45 90 75-90 660 800 631 375 330 335 - 8.5 17 51
H9 IP20 2.2-7.5 269 374 257 130 110 205 11 5.5 9 6.6
H10 IP20 11-15 399 419 380 165 140 248 12 6.8 7.5 12
I2 IP54 0.75-4.0 332 - 318.5 115 74 225 11 5.5 9 5.3
I3 IP54 5.5-7.5 368 - 354 135 89 237 12 6.5 9.5 7.2
I4 IP54 11-18.5 476 - 460 180 133 290 12 6.5 9.5 13.8
I5 IP54 11-18.5 480 - 454 242 210 260 19 9 9 23
I6 IP54 22-37 650 - 624 242 210 260 19 9 9 27
I7 IP54 45-55 680 - 648 308 272 310 19 9 9.8 45
I8 IP54 75-90 770 - 739 370 334 335 19 9 9.8 65
Table 1.9
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 5
1 1
Downloaded from www.Manualslib.com manuals search engine
The dimensions are only for the physical units, but wheninstalling in an application it is necessary to add space forfree air passage both above and below the units. Theamount of space for free air passage is listed in Table 1.10:
Enclosure Clearance needed for free air passage [mm]
Frame IP class Above unit Below unit
H1 20 100 100
H2 20 100 100
H3 20 100 100
H4 20 100 100
H5 20 100 100
H6 20 200 200
H7 20 200 200
H8 20 225 225
H9 20 100 100
H10 20 200 200
I2 54 100 100
I3 54 100 100
I4 54 100 100
I5 54 200 200
I6 54 200 200
I7 54 200 200
I8 54 225 225
Table 1.10 Clearance Needed for Free Air Passage [mm]
1.3.4 Electrical Installation in General
All cabling must comply with national and localregulations on cable cross-sections and ambienttemperature. Copper conductors required, (75 °C)recommended.
Power [kW] Torque [Nm]
Frame IP class 3x200-240 V 3x380-480 V Line Motor DCconnection
Controlterminals
Earth Relay
H1 IP20 0.25-1.5 0.37-1.5 1.4 0.8 0.8 0.5 0.8 0.5
H2 IP20 2.2 2.2-4 1.4 0.8 0.8 0.5 0.8 0.5
H3 IP20 3.7 5.5-7.5 1.4 0.8 0.8 0.5 0.8 0.5
H4 IP20 5.5-7.5 11-15 1.2 1.2 1.2 0.5 0.8 0.5
H5 IP20 11 18.5-22 1.2 1.2 1.2 0.5 0.8 0.5
H6 IP20 15-18 30-45 4.5 4.5 - 0.5 3 0.5
H7 IP20 22-30 55 10 10 - 0.5 3 0.5
H7 IP20 - 75 14 14 - 0.5 3 0.5
H8 IP20 37-45 90 242 242 - 0.5 3 0.5
Table 1.11
Power [kW] Torque [Nm]
Frame IP class 3x380-480 V Line Motor DC connection Controlterminals
Earth Relay
I2 IP54 0.75-4.0 1.4 0.8 0.8 0.5 0.8 0.5
I3 IP54 5.5-7.5 1.4 0.8 0.8 0.5 0.8 0.5
I4 IP54 11-18.5 1.4 0.8 0.8 0.5 0.8 0.5
I5 IP54 11-18.5 1.8 1.8 - 0.5 3 0.6
I6 IP54 22-37 4.5 4.5 - 0.5 3 0.6
I7 IP54 45-55 10 10 - 0.5 3 0.6
I8 IP54 75-90 14/241 14/241 - 0.5 3 0.6
Table 1.12
Quick Guide VLT® HVAC Basic Drive Quick Guide
6 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Power [kW] Torque [Nm]
Frame IP class 3x525-600 V Line Motor DC connection Controlterminals
Earth Relay
H9 IP20 2.2-7.5 1.8 1.8 notrecommended
0.5 3 0.6
H10 IP20 11-15 1.8 1.8 notrecommended
0.5 3 0.6
H6 IP20 18.5-30 4.5 4.5 - 0.5 3 0.5
H7 IP20 37-55 10 10 - 0.5 3 0.5
H8 IP20 75-90 14/241 14/241 - 0.5 3 0.5
Table 1.13 Details of Tightening Torques
1 Cable dimensions ≤95 mm2
2 Cable dimensions >95 mm2
1.3.5 Connecting to Mains and Motor
The frequency converter is designed to operate allstandard three-phased asynchronous motors. Formaximum cross-section on wires see 1.6 General Specifi-cations.
• Use a shielded/armored motor cable to complywith EMC emission specifications, and connectthis cable to both the decoupling plate and themotor metal.
• Keep motor cable as short as possible to reducethe noise level and leakage currents.
• For further details on mounting of thedecoupling plate, see FC 101 De-coupling PlateMounting Instruction MI02Q.
• Also see EMC-Correct Installation in the VLT® HVACBasic Design Guide, MG18C.
1. Mount the earth wires to earth terminal.
2. Connect motor to terminals U, V and W.
3. Mount mains supply to terminals L1, L2 and L3and tighten.
130B
B634
.10
1
2
2
3
4
Motor
U V W -DC+DC
MAINS
Illustration 1.3 H1-H5 FrameIP20 200-240 V 0.25-11 kW and IP20 380-480 V 0.37-22 kW.
1 Line
2 Earth
3 Motor
4 Relays
Table 1.14
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 7
1 1
Downloaded from www.Manualslib.com manuals search engine
1
95
99
L1 91 / L2 92 / L3 93
U 96 / V 97 / W 98
03 02 0106 05 04
2 3 413
0BB7
62.1
0Illustration 1.4 H6 FrameIP20 380-480 V 30-45 kWIP20 200-240 V 15-18.5 kWIP20 525-600 V 22-30 kW
1 Line
2 Motor
3 Earth
4 Relays
Table 1.15
1 2
3
4
130B
B763
.10
Illustration 1.5 H7 FrameIP20 380-480 V 55-75 kWIP20 200-240 V 22- 30 kWIP20 525-600 V 45-55 kW
1 Line
2 Relays
3 Earth
4 Motor
Table 1.16
Quick Guide VLT® HVAC Basic Drive Quick Guide
8 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
130B
B764
.10
1
2
3
4
989796
99
95939291
L1 L1 L1
U V w
Illustration 1.6 H8 FrameIP20 380-480 V 90 kWIP20 200-240 V 37-45 kWIP20 525-600 V 75-90 kW
1 Line
2 Relays
3 Earth
4 Motor
Table 1.17
MOTOR
MOTORU V W
99
130B
T302
.12
Illustration 1.7 H9 FrameIP20 600 V 2.2-7.5 kW
-DC+DC BR- BR+ U V W
99
M A I N S
95
RELA
Y 1
REL
AY 2
- LC
+
130B
A26
1.10
Illustration 1.8
130B
A26
2.10
M
I N S
+DCBR-
BR+U
V
W
RELA
Y 1
RELA
Y 295
Illustration 1.9
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 9
1 1
Downloaded from www.Manualslib.com manuals search engine
130B
A26
3.10
95
MA
I NS
+DC BR- BR+U
VW
91 92 93
L1L2 L3 RE
LAY
1
REL
AY 2
Illustration 1.10
+DC BR- BR+U
VW
MA
I NS
L1 L2 L391 92 93
RELA
Y 1
R
ELAY
2
99
- LC
-
130B
A26
4.10
Illustration 1.1113
0BA
725.
10
Illustration 1.12 H10 FrameIP20 600 V 11-15 kW
Quick Guide VLT® HVAC Basic Drive Quick Guide
10 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
130B
C29
9.10
7
3
2
5
1
8
4
6
Illustration 1.13 I2 FrameIP54 380-480 V 0.75-4.0 kW
1 RS-485
2 Line in
3 Earth
4 Wire clamps
5 Motor
6 UDC
7 Relays
8 I/O
Table 1.1813
0BC
201.
10
Illustration 1.14 I3 FrameIP54 380-480 V 5.5-7.5 kW
1 RS-485
2 Line in
3 Earth
4 Wire clamps
5 Motor
6 UDC
7 Relays
8 I/O
Table 1.19
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 11
1 1
Downloaded from www.Manualslib.com manuals search engine
130B
D01
1.10
Illustration 1.15 I4 FrameIP54 380-480 V 0.75-4.0 kW
1 RS-485
2 Line in
3 Earth
4 Wire clamps
5 Motor
6 UDC
7 Relays
8 I/O
Table 1.20
130B
C203
.10
Illustration 1.16 IP54 I2-I3-I4 frame
130B
T326
.10
Illustration 1.17 I6 FrameIP54 380-480 V 22-37 kW
130B
T325
.10
Illustration 1.18 I6 FrameIP54 380-480 V 22-37 kW
Quick Guide VLT® HVAC Basic Drive Quick Guide
12 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
311
130B
A21
5.10
RELAY 1RELAY 2
9
9
6
03 02 01
90 05 04
Illustration 1.19 I6 FrameIP54 380-480 V 22-37 kW
91L1
92L2
93L3
96U
97V
98W
88DC-
89DC+
81R-
8R+
9995
130B
A24
8.10
Illustration 1.20 I7, I8 FrameIP54 380-480 V 45-55 kWIP54 380-480 V 75-90 kW
1.3.6 Fuses
Branch circuit protectionIn order to protect the installation against electrical andfire hazard, all branch circuits in an installation, switchgear, machines etc., must be short-circuit and overcurrentprotected according to national/international regulations.
Short circuit protectionDanfoss recommends using the fuses mentioned in thefollowing tables to protect service personnel or otherequipment in case of an internal failure in the unit orshort-circuit on DC-link. The frequency converter providesfull short circuit protection in case of a short-circuit on themotor.
Overcurrent protectionProvide overload protection to avoid overheating of thecables in the installation. Overcurrent protection mustalways be carried out according to national regulations.Fuses must be designed for protection in a circuit capableof supplying a maximum of 100,000 Arms (symmetrical),480 V maximum.
Non UL complianceIf UL/cUL is not to be complied with, Danfoss recommendsusing the fuses mentioned in Table 1.21, which ensurescompliance with IEC 61800-5-1.In case of malfunction, not following the fuse recommen-dation may result in damage to the frequency converter.
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 13
1 1
Downloaded from www.Manualslib.com manuals search engine
Circuit Breaker Fuse
UL Non UL UL Non UL Bussmann Bussmann Bussmann Bussmann Max fuse
Power [kW] Type RK5 Type RK1 Type J Type T Type G3x200-240 V IP20
0.25
FRS-R-10 KTN-R10 JKS-10 JIN-10 10
0.37 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
0.75 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
1.5 FRS-R-10 KTN-R10 JKS-10 JIN-10 10
2.2 FRS-R-15 KTN-R15 JKS-15 JIN-15 16
3.7 FRS-R-25 KTN-R25 JKS-25 JIN-25 25
5.5 FRS-R-50 KTN-R50 JKS-50 JIN-50 50
7.5 FRS-R-50 KTN-R50 JKS-50 JIN-50 50
11 FRS-R-80 KTN-R80 JKS-80 JIN-80 65
15 Cutler-HammerEGE3100FFG
Moeller NZMB1-A125
FRS-R-100 KTN-R100
125
18.5 FRS-R-100 KTN-R100 125
22 Cutler-HammerJGE3150FFG
Moeller NZMB1-A160
FRS-R-150 KTN-R150 160
30 FRS-R-150 KTN-R150 160
37 Cutler-HammerJGE3200FFG
Moeller NZMB1-A200
FRS-R-200 KTN-R200 200
45 FRS-R-200 KTN-R200 200
3x380-480 V IP20
0.37
FRS-R-10 KTS-R10 JKS-10 JJS-10 10
0.75 FRS-R-10 KTS-R10 JKS-10 JJS-10 10
1.5 FRS-R-10 KTS-R10 JKS-10 JJS-10 10
2.2 FRS-R-15 KTS-R15 JKS-15 JJS-15 16
3 FRS-R-15 KTS-R15 JKS-15 JJS-15 16
4 FRS-R-15 KTS-R15 JKS-15 JJS-15 16
5.5 FRS-R-25 KTS-R25 JKS-25 JJS-25 25
7.5 FRS-R-25 KTS-R25 JKS-25 JJS-25 25
11 FRS-R-50 KTS-R50 JKS-50 JJS-50 50
15 FRS-R-50 KTS-R50 JKS-50 JJS-50 50
18.5 FRS-R-80 KTS-R80 JKS-80 JJS-80 65
22 FRS-R-80 KTS-R80 JKS-80 JJS-80 65
30Cutler-Hammer
EGE3125FFGMoeller NZMB1-
A125
FRS-R-80 KTS-R80 JKS-R80 JJS-R80 80
37 FRS-R-100 KTS-R100 JKS-R100 JJS-R100 100
45 FRS-R-125 KTS-R125 JKS-R125 JJS-R125 125
55 Cutler-HammerJGE3200FFG
Moeller NZMB1-A200
FRS-R-150 KTS-R150 JKS-R150 JJS-R150 150
75 FRS-R-200 KTS-R200 JKS-R200 JJS-R200 200
90Cutler-Hammer
JGE3250FFGMoeller NZMB2-
A250FRS-R-250 KTS-R250 JKS-R250 JJS-R250 250
Table 1.21
Quick Guide VLT® HVAC Basic Drive Quick Guide
14 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Circuit Breaker Fuse
UL Non UL UL Non UL Bussmann Bussmann Bussmann Bussmann Max fuse
Power [kW] Type RK5 Type RK1 Type J Type T Type G3x525-600 V IP20
2.2
KTS-R20
20
3 KTS-R20 20
3.7 KTS-R20 20
5.5 KTS-R20 20
7.5 KTS-R20 30
11
KTS-R30 35
15 KTS-R30 35
18.5Cutler-Hammer
EGE3080FFGCutler-Hammer
EGE3080FFG
FRS-R-80 KTN-R80 80
22 FRS-R-80 KTN-R80 80
30 FRS-R-80 KTN-R80 80
37Cutler-Hammer
JGE3125FFGCutler-Hammer
JGE3125FFG
FRS-R-125 KTN-R125 125
45 FRS-R-125 KTN-R125 125
55 FRS-R-125 KTN-R125 125
75 Cutler-HammerJGE3200FAG
Cutler-HammerJGE3200FAG
FRS-R-200 KTN-R200 200
90 FRS-R-200 KTN-R200 200
3x380-480 V IP54
0.75
1.5
2.2
3
4
5.5
7.5
11
15
18.5
22
Moeller NZMB1-A125
125
30 125
37 125
45Moeller NZMB2-A160
160
55 160
75Moeller NZMB2-A250
200
90 200
Table 1.22 Fuses
1.3.7 EMC-Correct Electrical Installation
General points to be observed to ensure EMC-correctelectrical installation.
• Use only screened/armoured motor cables andscreened/armoured control cables.
• Connect the screen to earth at both ends.
• Avoid installation with twisted screen ends(pigtails), since this ruins the screening effect at
high frequencies. Use the cable clamps providedinstead.
• It is important to ensure good electrical contactfrom the installation plate through the installationscrews to the metal cabinet of the frequencyconverter.
• Use starwashers and galvanically conductiveinstallation plates.
• Do not use unscreened/unarmoured motor cablesin the installation cabinets.
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 15
1 1
Downloaded from www.Manualslib.com manuals search engine
Back
OK
Com.
On
Warn.
Alarm
HandOn
O�Reset
AutoOn
Menu Status QuickMenu
MainMenu
L1
L2L3
PE
Min. 16 mm2
Equalizing cable
Control cables
All cable entries in
one side of panel
Earthing rail
Cable insula-tion stripped
Output con-tactor etc.
Motor cable
Motor, 3 phases and
PLC etc. Panel
Mains-supply
Min. 200mmbetween control cable, mains cable and between mains motor cable
PLC
Protective earthReinforced protective earth
130B
B761
.11
Illustration 1.21 EMC-correct Electrical Installation
NOTEFor North America use metal conduits instead of shieldedcables.
Quick Guide VLT® HVAC Basic Drive Quick Guide
16 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.3.8 Control Terminals
IP20 200-240 V 0.25-11 kW and IP20 380-480 V 0.37-22 kW:
130B
B622
.10
Illustration 1.22 Location of Control Terminals
1. Place a screwdriver behind the terminal cover toactivate snap.
2. Tilt the screwdriver outwards to open the cover.
130B
B624
.10
Illustration 1.23 IP20 380-480 V 30-90 kW
1. Place a screwdriver behind the terminal cover toactivate snap.
2. Tilt the screwdriver outwards to open the cover.
Digital input 18, 19 and 27 mode is set in 5-00 Digital InputMode (PNP is default value) and digital input 29 mode isset in 5-03 Digital Input 29 Mode (PNP is default value).
130B
C24
9.10
Illustration 1.24 IP54 400 V 0.75-7.5 kW
1. Remove the front cover.
Control terminalsIllustration 1.25 shows all control terminals of the frequencyconverter. Applying Start (term. 18), connection betweenterminal 12-27 and an analog reference (term. 53 or 54and 55) make the frequency converter run.
18 19
12 20 55
27 29 42 45 50 53 54
DIG
I IN
DIG
I IN
DIG
I IN
DIG
I IN
61 68 69
NPCOM
M. G
ND
+24V
0/4-20mA A OUT / DIG OUT 0/4-20mA A OUT / DIG OUT
GND
GND
10V/20mA
IN
10V/20mA
IN
10V OU
T
130B
B625
.10BUS TER.
OFF ON
Illustration 1.25 Control Terminals
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 17
1 1
Downloaded from www.Manualslib.com manuals search engine
1.3.9 Electrical Overview
L1L2L3
3 Phasepowerinput
PE PE
+10Vdc
0-10Vdc-
0-10Vdc-
50 (+10V OUT)
54 (A IN)
53 (A IN)
55 (COM A IN/OUT)
0/4-20 mA
0/4-20 mA
42 0/4-20mA A OUT / DIG OUT
45 0/4-20mA A OUT / DIG OUT
18 (DIGI IN)
19 (DIGI IN)
27 (DIGI IN)
29 (DIGI IN)
12 (+24V OUT)
24V (NPN)
20 (COM D IN)
OV (PNP)
24V (NPN)OV (PNP)
24V (NPN)OV (PNP)
24V (NPN)OV (PNP)
Bus ter.
Bus ter.
RS-485Interface RS-485(N PS-485) 69
(P RS-485) 68
(Com RS-485 ) 61
(PNP)-Source(NPN)-Sink
ON=TerminatedOFF=Unterminated
ON
12
240V AC 3A
Not present on all power sizes
Do not connect shield to61 on 116,117 and 118 unites
01
02
03relay1
relay2
UDC+
UDC-
Motor
UV
W
130B
B626
.10
06
05
04
240V AC 3A
Illustration 1.26
NOTEThere is no access to UDC- and UDC+ on the following units:IP20 380-480 V 30-90 kWIP20 200-240 V 15-45 kWIP20 525-600 V 2.2-90 kWIP54 380-480 V 22-90 kW
Quick Guide VLT® HVAC Basic Drive Quick Guide
18 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.4 Programming
1.4.1 Programming with the Local ControlPanel (LCP)
NOTEThe frequency converter can also be programmed from aPC via RS-485 com-port by installing the MCT 10 Set-upSoftware. This software can either be ordered using codenumber 130B1000 or downloaded from the Danfoss Website: www.danfoss.com/BusinessAreas/DrivesSolutions/softwar-edownload
1.4.2 Local Control Panel (LCP)
The following instructions are valid for the FC 101 LCP. TheLCP is divided into four functional sections.
A. Alphanumeric display
B. Menu key
C. Navigation keys and indicator lights (LEDs)
D. Operation keys and indicator lights (LEDs)
130B
B765
.11
Back
Com.
1-20 Motor Power[5] 0.37kW - 0.5HPSetup 1
A
B
1
12
13 14 15
11
11
10
9
8
7
6
54
3
2
C
D
Status MainMenu
QuickMenu
HandOn
OK
Menu
O�Reset
AutoOn
Alarm
Warn.
On
11
Illustration 1.27
A. Alpha Numeric DisplayThe LCD-display is back-lit with 2 alpha-numeric lines. Alldata is displayed on the LCP.
Information can be read from the display.
1 Parameter number and name.
2 Parameter value.
3 Set-up number shows the active set-up and the edit set-up. If the same set-up acts as both active and edit set-up,only that set-up number is shown (factory setting). Whenactive and edit set-up differ, both numbers are shown inthe display (Setup 12). The number flashing, indicates theedit set-up.
4 Motor direction is shown to the bottom left of the display– indicated by a small arrow pointing either clockwise orcounterclockwise.
5 The triangle indicates if the LCP is in status, quick menu ormain menu.
Table 1.23
B. Menu keyUse the menu key to select between status, quick menu ormain menu.
C. Navigation keys and indicator lights (LEDs)
6 Com led: Flashes when bus communication is communi-cating.
7 Green LED/On: Control section is working.
8 Yellow LED/Warn.: Indicates a warning.
9 Flashing Red LED/Alarm: Indicates an alarm.
10 [Back]: For moving to the previous step or layer in thenavigation structure
11 [▲] [▼] [►]: For maneuvering between parameter groups,
parameters and within parameters. Can also be used forsetting local reference.
12 [OK]: For selecting a parameter and for accepting changes toparameter settings
Table 1.24
D. Operation keys and indicator lights (LEDs)
13 [Hand On]: Starts the motor and enables control of thefrequency converter via the LCP.
NOTETerminal 27 Digital Input (5-12 Terminal 27 DigitalInput) has coast inverse as default setting. This meansthat [Hand On] not starts the motor if there is no 24V to terminal 27. Connect terminal 12 to terminal 27.
14 [Off/Reset]: Stops the motor (Off). If in alarm mode thealarm will be reset.
15 [Auto On]: frequency converter is controlled either viacontrol terminals or serial communication.
Table 1.25
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 19
1 1
Downloaded from www.Manualslib.com manuals search engine
At power-upAt the first power-up, select the preferred language. Onceselected, this screen never shows again in the followingpowerups, but language can still be changed in0-01 Language.
130B
B628
.10Select Language
[ 0 ] EnglishSetup 1
Illustration 1.28
1.4.3 The Start-up Wizard for Open LoopApplications
The built-in “wizard” menu guides the installer through thesetup of the frequency converter in a clear and structuredmanner to setup an open loop application. An open loopapplication is here an application with a start signal,analog reference (voltage or current) and optionally alsorelay signals (but no feed back signal from the processapplied).
FC+24V
DIG INDIG IN
DIG INDIG IN
COM DIG IN
A OUT / D OUTA OUT / D OUT
1819
2729
4255
505354
20
12
010203
040506
R2R1
+
-0-10V
Start
+10VA INA INCOM
130B
B674
.10
45
Reference
Illustration 1.29
The wizard will initially be shown after power up until anyparameter has been changed. The wizard can always beaccessed again through the quick menu. Press [OK] to startthe wizard. If [Back] is pressed, the FC 101 returns to thestatus screen.
130B
B629
.10Press OK to start Wizard
Push Back to skip itSetup 1
Illustration 1.30
Quick Guide VLT® HVAC Basic Drive Quick Guide
20 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Setup 1Power kW/50 Hz
Setup 1
Set Motor Speed low LimitHz
Setup 1
Set Motor Speed high Limit Hz
Setup 1
Set Ramp 1 ramp-up time s
Setup 1
Set Ramp 1 ramp-down Times
Setup 1
Active Flying start? Disable
OK
5
Setup 1
Set Motor Power7
Setup 1
Set Motor Voltage8
Setup 1
Set Motor frequency9
Setup 1
Set Motor current10
Setup 1
Set Motor nominal speed 11
if
17
20
21
22
Select Regional Settings
... the HVAC FC 101 Wizard starts
Setup 1200-240V/50Hz/Delta
Grid Type
4
Asynchronous MotorSetup 1Asynchronous
Select Motor Type 6
Setup 1
Set Motor current12
Setup 1
Select Motor nominal speed13
Setup 1
Set Motor Cont. Rated Torque14
Setup 1
Stator resistance15
Setup 1
Motor poles16
Setup 1
Back EMF at 1000 rpm
18
Setup 1
d-axis inductance
19Setup 1
Set Max Output Frequency
23
24
Setup 1
Setup 1Setup 1
Setup 1
Set T53 low VoltageV
Set T53 high VoltageV
Set T53 Low CurrentA
Set T53 High CurrentA
Current Voltage
28
29
26
27
Setup 1
Setup 1 Setup 1 Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
Setup 1
AMA Failed
0.0 Hz0.0 kW
Wizard completedPress OK to accept
Automatic Motor Adaption O�
Auto Motor Adapt OKPress OK
Select Function of Relay 2 No function
Select Function of Relay 1[0] No function
Set Max ReferenceHz
Set Min ReferenceHz
AMA running-----
AMA failed
Do AMA
(Do not AMA)
AMA OK
30
31
32
33
34
3738
39
35 36
[0]
[0]
[0]
Setup 1
Select T53 ModeCurrent 25
[0]
[0]
3.8 A
3000 RPM
5.4 Nm
0.65 Ohms
8
57 V
5 mH
0065 Hz
1.50 kW
0050 V
0050 Hz
04.66 A
1420 RPM
[0]
PM motor
Motor Type = Asynchronous
Motor Type = PM Motor
0000
0050
0003
0003
[0]
[0]
04.66
13.30
0050
0220
0000
0050
OK
Back
Status MainMenu
QuickMenu
HandOn
OK
Menu
O�Reset
AutoOn
Alarm
Warn.
On
Status Screen
The Wizard can always be
reentered via the Quick Menu!
Power Up Screen
At power up the user isasked to choose theprefered laguage.
Select language[1] English
0.0 Hz0.0 kW
Setup 1
Setup 1
Status MainMenu
QuickMenu
HandOn
OK
Menu
O�Reset Auto
On
Alarm
Warn.
On
Press OK to start WizardPress Back to skip it
Setup 1
Status MainMenu
QuickMenu
HandOn
OK
Menu
O�Reset
AutoOn
Alarm
Warn.
On
The next screen will be
the Wizard screen.
Wizard Screen
1
2
if
3
Back
Back
Back
Com.
Com.
Com.
130B
C244
.11
Illustration 1.31
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 21
1 1
Downloaded from www.Manualslib.com manuals search engine
The FC 101 Start-up Wizard for Open Loop ApplicationsNo & Name Range Default Function0-03 Regional Settings [0] International
[1] US0
0-06 GridType [0] 200-240 V/50 Hz/IT-grid[1] 200-240 V/50 Hz/Delta[2] 200-240 V/50 Hz[10] 380-440 V/50 Hz/IT-grid[11] 380-440 V/50 Hz/Delta[12] 380-440 V/50 Hz[20] 440-480 V/50 Hz/IT-grid[21] 440-480 V/50 Hz/Delta[22] 440-480 V/50 Hz[30] 525-600 V/50 Hz/IT-grid[31] 525-600 V/50 Hz/Delta[32] 525-600 V/50 Hz[100] 200-240 V/60 Hz/IT-grid[101] 200-240 V/60 Hz/Delta[102] 200-240 V/60 Hz[110] 380-440 V/60 Hz/IT-grid[111] 380-440 V/60 Hz/Delta[112] 380-440 V/60 Hz[120] 440-480 V/60 Hz/IT-grid[121] 440-480 V/60 Hz/Delta[122] 440-480 V/60 Hz[130] 525-600 V/60 Hz/IT-grid[131] 525-600 V/60 Hz/Delta[132] 525-600 V/60 Hz
Size related Select operating mode for restart uponreconnection of the drive to mains voltage afterpower down
1-10 Motor Construction *[0] Asynchron[1] PM, non salient SPM
[0] Asynchron Setting the parameter value might change theseparameters:1-01 Motor Control Principle1-03 Torque Characteristics1-14 Damping Gain1-15 Low Speed Filter Time Const.1-16 High Speed Filter Time Const.1-17 Voltage filter time const.1-20 Motor Power [kW]1-22 Motor Voltage1-23 Motor Frequency1-24 Motor Current1-25 Motor Nominal Speed1-26 Motor Cont. Rated Torque1-30 Stator Resistance (Rs)1-33 Stator Leakage Reactance (X1)1-35 Main Reactance (Xh)1-37 d-axis Inductance (Ld)1-39 Motor Poles1-40 Back EMF at 1000 RPM1-66 Min. Current at Low Speed1-72 Start Function1-73 Flying Start4-19 Max Output Frequency4-58 Missing Motor Phase Function
1-20 Motor Power 0.12-110 kW/0.16-150 hp Size related Enter motor power from nameplate data
1-22 Motor Voltage 50.0-1000.0 V Size related Enter motor voltage from nameplate data
1-23 Motor Frequency 20.0-400.0 Hz Size related Enter motor frequency from nameplate data
Quick Guide VLT® HVAC Basic Drive Quick Guide
22 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
No & Name Range Default Function1-24 Motor Current 0.01-10000.00 A Size related Enter motor current from nameplate data
1-25 Motor NominalSpeed
100.0-9999.0 RPM Size related Enter motor nominal speed from nameplate data
1-26 Motor Cont. RatedTorque
0.1-1000.0 Size related This parameter is available only when 1-10 MotorConstruction Design is set to [1] PM, non-salientSPM .
NOTEChanging this parameter will affect settingsof other parameters
1-29 Automatic MotorAdaption (AMA)
See 1-29 Automatic Motor Adaption(AMA)
Off Performing an AMA optimizes motor performance
1-30 Stator Resistance(Rs)
0.000-99.990 Size related Set the stator resistance value
1-37 d-axis Inductance(Ld)
0-1000 Size related Enter the value of the d-axis inductance.Obtain the value from the permanent magnetmotor data sheet. The de-axis inductance cannotbe found by performing an AMA.
1-39 Motor Poles 2-100 4 Enter the number of motor poles
1-40 Back EMF at 1000RPM
10-9000 Size related Line-Line RMS back EMF voltage at 1000 RPM
1-73 Flying Start When PM is selected, Flying Start is enabled andcan not disable
1-73 Flying Start [0] Disabled[1] Enabled
0 Select [1] Enable to enable the drive to catch amotor spinning due to mains drop-out. Select [0]Disable if this function is not required. When isenabled 1-71 Start Delay and 1-72 Start Functionhave no function. is active in VVC+ mode only
3-02 Minimum Reference -4999-4999 0 The minimum reference is the lowest valueobtainable by summing all references
3-03 Maximum Reference -4999-4999 50 The maximum reference is the lowest obtainableby summing all references
3-41 Ramp 1 Ramp UpTime
0.05-3600.0 s Size related Ramp up time from 0 to rated 1-23 MotorFrequency if Asynchron motor is selected; ramp uptime from 0 to 1-25 Motor Nominal Speed if PMmotor is selected
3-42 Ramp 1 RampDown Time
0.05-3600.0 s Size related Ramp down time from rated 1-23 MotorFrequency to 0 if Asynchron motor is selected;ramp down time from 1-25 Motor Nominal Speedto 0 if PM motor is selected
4-12 Motor Speed LowLimit [Hz]
0.0-400 Hz 0 Hz Enter the minimum limit for low speed
4-14 Motor Speed HighLimit [Hz]
0.0-400 Hz 65 Hz Enter the maximum limit for high speed
4-19 Max OutputFrequency
0-400 Size related Enter the maximum output frequency value
5-40 Function Relay [0]Function relay
See 5-40 Function Relay Alarm Select the function to control output relay 1
5-40 Function Relay [1]Function relay
See 5-40 Function Relay Drive running Select the function to control output relay 2
6-10 Terminal 53 LowVoltage
0-10 V 0.07 V Enter the voltage that corresponds to the lowreference value
6-11 Terminal 53 HighVoltage
0-10 V 10 V Enter the voltage that corresponds to the highreference value
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 23
1 1
Downloaded from www.Manualslib.com manuals search engine
No & Name Range Default Function6-12 Terminal 53 LowCurrent
0-20 mA 4 Enter the current that corresponds to the lowreference value
6-13 Terminal 53 HighCurrent
0-20 mA 20 Enter the current that corresponds to the highreference value
6-19 Terminal 53 mode [0] Current[1] Voltage
1 Select if terminal 53 is used for current- or voltageinput
Table 1.26
Quick Guide VLT® HVAC Basic Drive Quick Guide
24 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Closed Loop Set-up Wizard
6-29 Terminal 54 Mode[1] Voltage
6-25 T54 high Feedback
0050 Hz20-94 PI integral time0020.00 s
Current Voltage
This dialog is forced to be set to [1] Analog input 54
27
28
29
30
31
32
33
34
20-00 Feedback 1 source[1] Analog input 54
3-10 Preset reference [0]0.00
3-03 Max Reference50.00
3-02 Min Reference0.00
Asynchronous Motor
1-73 Flying Start [0] No
1-22 Motor Voltage0050 V
1-24 Motor current04.66 A
1-25 Motor nominal speed1420 RPM
3-41 Ramp 1 ramp-up time0003 s
3-42 Ramp1 ramp-down time0003 s
5
6
7
8
9
18
19
20
21
22
22a
23
24
25
26
35
36
37
38
39
40
0-06 Grid Type
4-12 Motor speed low limit0016 Hz
4-13 Motor speed high limit0050 Hz
130B
C402
.10
1-20 Motor Power1.10 kW
1-23 Motor frequency0050 Hz
6-22 T54 Low Current A
6-24 T54 low Feedback0016 Hz
6-23 T54 high Current13.30 A
6-25 T54 high Feedback0050
0.01 s
20-81 PI Normal/Inverse Control[0] Normal
20-83 PI Normal/Inverse Control0050 Hz
20-93 PI Proportional Gain00.50
1-29 Automatic Motor Adaption[0] O�
6-20 T54 low Voltage0050 V
6-24 T54 low Feedback0016 Hz
6-21 T54 high Voltage0220 V
6-26 T54 Filter time const.
1-00 Con�guration Mode[3] Closed Loop3
0-03 Regional Settings[0] Power kW/50 Hz1
3-16 Reference Source 2[0] No Operation22b
1-10 Motor Type[0] Asynchronous4
2 [0] 200-240V/50Hz/Delta
1-30 Stator resistance0.65 Ohms
1-25 Motor nominal speed3000 RPM
1-24 Motor Current3.8 A
1-26 Motor Cont. Rated Torque5.4 Nm
1-37 d-axis inductance(Ld)5 mH
4-19 Max Ouput Frequency0065 Hz
1-40 Back EMF at 1000 rpm57 V
10
11
12
13
14
15
16
17
PM motor
1-39 Motor poles8
%
04.66
Hz
MotorType = Asynchronous
MotorType = PM Motor
Illustration 1.32
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 25
1 1
Downloaded from www.Manualslib.com manuals search engine
Closed Loop Set-up WizardNo & Name Range Default Function0-03 Regional Settings [0] International
[1] US0
0-06 GridType [0] -[[132] see start -up wizardfor open loop application
Size selected Select operating mode for restart uponreconnection of the frequency converter tomains voltage after power down
1-00 Configuration Mode [0] Open loop[3] Closed loop
0 Change this parameter to Closed loop
1-10 Motor Construction *[0] Motor construction[1] PM, non salient SPM
[0] Asynchron Setting the parameter value might changethese parameters:1-01 Motor Control Principle1-03 Torque Characteristics1-14 Damping Gain1-15 Low Speed Filter Time Const.1-16 High Speed Filter Time Const.1-17 Voltage filter time const.1-20 Motor Power [kW]1-22 Motor Voltage1-23 Motor Frequency1-25 Motor Nominal Speed1-26 Motor Cont. Rated Torque1-30 Stator Resistance (Rs)1-33 Stator Leakage Reactance (X1)1-35 Main Reactance (Xh)1-37 d-axis Inductance (Ld)1-39 Motor Poles1-40 Back EMF at 1000 RPM1-66 Min. Current at Low Speed1-72 Start Function1-73 Flying Start4-19 Max Output Frequency4-58 Missing Motor Phase Function
1-20 Motor Power 0.09-110 kW Size related Enter motor power from nameplate data
1-22 Motor Voltage 50.0-1000.0 V Size related Enter motor voltage from nameplate data
1-23 Motor Frequency 20.0-400.0 Hz Size related Enter motor frequency from nameplate data
1-24 Motor Current 0.0 -10000.00 A Size related Enter motor current from nameplate data
1-25 Motor Nominal Speed 100.0-9999.0 RPM Size related Enter motor nominal speed from nameplatedata
1-26 Motor Cont. Rated Torque 0.1-1000.0 Size related This parameter is available only when1-10 Motor Construction Design is set to [1]PM, non-salient SPM .
NOTEChanging this parameter affects settingsof other parameters
1-29 Automatic Motor Adaption(AMA)
Off Performing an AMA optimizes motorperformance
1-30 Stator Resistance (Rs) 0.000-99.990 Size related Set the stator resistance value
1-37 d-axis Inductance (Ld) 0-1000 Size related Enter the value of the d-axis inductance.Obtain the value from the permanent magnetmotor data sheet. The de-axis inductancecannot be found by performing an AMA.
1-39 Motor Poles 2-100 4 Enter the number of motor poles
1-40 Back EMF at 1000 RPM 10-9000 Size related Line-Line RMS back EMF voltage at 1000 RPM
Quick Guide VLT® HVAC Basic Drive Quick Guide
26 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
No & Name Range Default Function1-73 Flying Start [0] Disabled
[1] Enabled0 Select [1] Enable to enable the frequency
converter to catch a spinning motor. I.e. fanapplications. When PM is selected, Flying Startis enabled.
3-02 Minimum Reference -4999-4999 0 The minimum reference is the lowest valueobtainable by summing all references
3-03 Maximum Reference -4999-4999 50 The maximum reference is the highest valueobtainable by summing all references
3-10 Preset Reference -100-100% 0 Enter the set point
3-41 Ramp 1 Ramp Up Time 0.05-3600.0 s Size related Ramp up time from 0 to rated 1-23 MotorFrequency if Asynchron motor is selected;ramp up time from 0 to 1-25 Motor NominalSpeed if PM motor is selected"
3-42 Ramp 1 Ramp Down Time 0.05-3600.0 s Size related Ramp down time from rated 1-23 MotorFrequency to 0 if Asynchron motor is selected;ramp down time from 1-25 Motor NominalSpeed to 0 if PM motor is selected
4-12 Motor Speed Low Limit [Hz] 0.0-400 Hz 0.0 Hz Enter the minimum limit for low speed
4-14 Motor Speed High Limit [Hz] 0-400 Hz 65 Hz Enter the minimum limit for high speed
4-19 Max Output Frequency 0-400 Size related Enter the maximum output frequency value
6-29 Terminal 54 mode [0] Current[1] Voltage
1 Select if terminal 54 is used for current- orvoltage input
6-20 Terminal 54 Low Voltage 0-10 V 0.07 V Enter the voltage that corresponds to the lowreference value
6-21 Terminal 54 High Voltage 0-10 V 10 V Enter the voltage that corresponds to the lowhigh reference value
6-22 Terminal 54 Low Current 0-20 mA 4 Enter the current that corresponds to the highreference value
6-23 Terminal 54 High Current 0-20 mA 20 Enter the current that corresponds to the highreference value
6-24 Terminal 54 Low Ref./Feedb.Value
-4999-4999 0 Enter the feedback value that corresponds tothe voltage or current set in 6-20 Terminal 54Low Voltage/6-22 Terminal 54 Low Current
6-25 Terminal 54 High Ref./Feedb.Value
-4999-4999 50 Enter the feedback value that corresponds tothe voltage or current set in 6-21 Terminal 54High Voltage/6-23 Terminal 54 High Current
6-26 Terminal 54 Filter TimeConstant
0-10 s 0.01 Enter the filter time comstant
20-81 PI Normal/ Inverse Control [0] Normal[1] Inverse
0 Select [0] Normal to set the process control toincrease the output speed when the processerror is positive. Select [1] Inverse to reducethe output speed.
20-83 PI Start Speed [Hz] 0-200 Hz 0 Enter the motor speed to be attained as astart signal for commencement of PI control
20-93 PI Proportional Gain 0-10 0.01 Enter the process controller proportional gain.Quick control is obtained at high amplifi-cation. However if amplification is too great,the process may become unstable
20-94 PI Integral Time 0.1-999.0 s 999.0 s Enter the process controller integral time.Obtain quick control through a short integraltime, though if the integral time is too short,the process becomes unstable. An excessivelylong integral time disables the integral action.
Table 1.27
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 27
1 1
Downloaded from www.Manualslib.com manuals search engine
Motor Set-upThe Quick Menu Motor Set-up guides through the neededmotor parameters.
No & Name Range Default Function0-03 RegionalSettings
[0] Interna-tional[1] US
0
0-06 GridType [0] -[132] seestart -upwizard foropen loopapplication
Size selected Select operatingmode for restartuponreconnection ofthe drive tomains voltageafter powerdown
1-10 MotorConstruction
*[0] Motorconstruction[1] PM, nonsalient SPM
[0]Asynchron
1-20 MotorPower
0.12-110 kW/0.16-150 hp
Size related Enter motorpower fromnameplate data
1-22 MotorVoltage
50.0-1000.0 V Size related Enter motorvoltage fromnameplate data
1-23 MotorFrequency
20.0-400.0 Hz Size related Enter motorfrequency fromnameplate data
1-24 MotorCurrent
0.01-10000.00A
Size related Enter motorcurrent fromnameplate data
1-25 MotorNominalSpeed
100.0-9999.0RPM
Size related Enter motornominal speedfrom nameplatedata
1-26 MotorCont. RatedTorque
0.1-1000.0 Size related This parameter isavailable onlywhen 1-10 MotorConstructionDesign is set to[1] PM, non-salient SPM.
NOTEChanging thisparameteraffects settingsof otherparameters
1-30 StatorResistance (Rs)
0.000-99.990 Size related Set the statorresistance value
No & Name Range Default Function1-37 d-axisInductance(Ld)
0-1000 Size related Enter the valueof the d-axisinductance.Obtain the valuefrom thepermanentmagnet motordata sheet. Thede-axisinductancecannot be foundby performing anAMA.
1-39 MotorPoles
2-100 4 Enter the numberof motor poles
1-40 Back EMFat 1000 RPM
10-9000 Size related Line-Line RMSback EMF voltageat 1000 RPM
1-73 FlyingStart
[0] Disabled[1] Enabled
0 Select Enable toenable thefrequencyconverter tocatch a spinningmotor
3-41 Ramp 1Ramp UpTime
0.05-3600.0 s Size related Ramp up timefrom 0 to rated1-23 MotorFrequency
3-42 Ramp 1Ramp DownTime
0.05-3600.0 s Size related Ramp down timefrom rated1-23 MotorFrequency to 0
4-12 MotorSpeed LowLimit [Hz]
0.0-400 Hz 0.0 Hz Enter theminimum limitfor low speed
4-14 MotorSpeed HighLimit [Hz]
0.0-400 Hz 65 Enter themaximum limitfor high speed
4-19 MaxOutputFrequency
0-400 Size related Enter themaximum outputfrequency value
Table 1.28
Quick Guide VLT® HVAC Basic Drive Quick Guide
28 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Changes MadeChanges Made lists all parameters changed since factorysetting. Only the changed parameters in current edit-setupare listed in changes made.
If the parameters value is changed back to factory setting'svalue from another different value, the parameter will NOTbe listed in Changes Made.
1. Press [Menu] key to enter the Quick Menu untilindicator in display is placed above Quick Menu.
2. Press [▲] [▼] to select either FC 101 wizard,closed loop setup, motor setup or changes made,then press [OK].
3. Press [▲] [▼] to browse through the parametersin the Quick Menu.
4. Press [OK] to select a parameter.
5. Press [▲] [▼] to change the value of a parametersetting.
6. Press [OK] to accept the change.
7. Press either [Back] twice to enter “Status”, orpress [Menu] once to enter “Main Menu”.
The Main Menu accesses all parameters.
1. Press [Menu] key until indicator in display isplaced above “Main Menu”.
2. Press [▲] [▼] to browse through the parametergroups.
3. Press [Ok] to select a parameter group.
4. Press [▲] [▼] to browse through the parametersin the specific group.
5. Press [Ok] to select the parameter.
6. Press [▲] [▼] to set/change the parameter value.
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 29
1 1
Downloaded from www.Manualslib.com manuals search engine
1.5.
1M
ain
men
ust
ruct
ure
0-**
Ope
ratio
n /
Dis
play
0-0*
Basi
c Se
ttin
gs0-
01La
ngua
ge0-
03Re
gion
al S
ettin
gs0-
04O
pera
ting
Sta
te a
t Po
wer
-up
0-06
Grid
Type
0-07
Aut
o D
C B
raki
ng0-
1*Se
t-up
Ope
ratio
ns0-
10A
ctiv
e Se
t-up
0-11
Prog
ram
min
g S
et-u
p0-
12Li
nk S
etup
s0-
3*LC
P C
usto
m R
eado
ut0-
30Cu
stom
Rea
dout
Uni
t0-
31Cu
stom
Rea
dout
Min
Val
ue0-
32Cu
stom
Rea
dout
Max
Val
ue0-
37D
ispl
ay T
ext
10-
38D
ispl
ay T
ext
20-
39D
ispl
ay T
ext
30-
4*LC
P K
eypa
d0-
40[H
and
on]
Key
on
LCP
0-42
[Aut
o o
n] K
ey o
n L
CP0-
44[O
ff/Re
set]
Key
on
LCP
0-5*
Copy
/Sav
e0-
50LC
P C
opy
0-51
Set-
up C
opy
0-6*
Pass
wor
d0-
60M
ain
Men
u P
assw
ord
1-**
Load
and
Mot
or1-
0*G
ener
al S
ettin
gs1-
00Co
nfig
urat
ion
Mod
e1-
01M
otor
Con
trol
Prin
cipl
e1-
03To
rque
Cha
ract
eris
tics
1-06
Cloc
kwis
e D
irect
ion
1-1*
Mot
or S
elec
tion
1-10
Mot
or C
onst
ruct
ion
1-14
Dam
ping
Gai
n1-
15Lo
w S
peed
Filt
er T
ime
Cons
t1-
16H
igh
Spe
ed F
ilter
Tim
e Co
nst
1-17
Volta
ge fi
lter
time
cons
t1-
2*M
otor
Dat
a1-
20M
otor
Pow
er1-
22M
otor
Vol
tage
1-23
Mot
or F
requ
ency
1-24
Mot
or C
urre
nt1-
25M
otor
Nom
inal
Spe
ed1-
26M
otor
Con
t. R
ated
Tor
que
1-29
Aut
omat
ic M
otor
Ada
ptio
n (A
MA
)1-
3*A
dv. M
otor
Dat
a1-
30St
ator
Res
ista
nce
(Rs)
1-33
Stat
or L
eaka
ge R
eact
ance
(X1)
1-35
Mai
n R
eact
ance
(Xh)
1-37
d-ax
is In
duct
ance
(Ld)
1-39
Mot
or P
oles
1-4*
Adv
. Mot
or D
ata
II1-
40Ba
ck E
MF
at 1
000
RPM
1-42
Mot
or C
able
Len
gth
1-43
Mot
or C
able
Len
gth
Fee
t1-
5*Lo
ad In
dep.
Set
ting
1-50
Mot
or M
agne
tisat
ion
at
Zero
Spe
ed1-
52M
in S
peed
Nor
mal
Mag
netis
ing
[Hz]
1-55
U/f
Cha
ract
eris
tic -
U1-
56U
/f C
hara
cter
istic
- F
1-6*
Load
Dep
en. S
ettin
g1-
60Lo
w S
peed
Loa
d C
ompe
nsat
ion
1-61
Hig
h S
peed
Loa
d C
ompe
nsat
ion
1-62
Slip
Com
pens
atio
n1-
63Sl
ip C
ompe
nsat
ion
Tim
e Co
nsta
nt1-
64Re
sona
nce
Dam
peni
ng1-
65Re
sona
nce
Dam
peni
ng T
ime
Cons
tant
1-66
Min
. Cur
rent
at
Low
Spe
ed1-
7*St
art
Adj
ustm
ents
1-71
Star
t D
elay
1-72
Star
t Fu
nctio
n1-
73Fl
ying
Sta
rt1-
8*St
op A
djus
tmen
ts1-
80Fu
nctio
n a
t St
op1-
82M
in S
peed
for
Func
tion
at
Stop
[Hz]
1-9*
Mot
or T
empe
ratu
re1-
90M
otor
The
rmal
Pro
tect
ion
1-93
Ther
mis
tor
Sour
ce2-
**Br
akes
2-0*
DC-
Brak
e2-
00D
C H
old/
Mot
or P
rehe
at C
urre
nt2-
01D
C B
rake
Cur
rent
2-02
DC
Bra
king
Tim
e2-
04D
C B
rake
Cut
In S
peed
2-06
Park
ing
Cur
rent
2-07
Park
ing
Tim
e2-
1*Br
ake
Ener
gy F
unct
.2-
10Br
ake
Func
tion
2-16
AC
Bra
ke, M
ax c
urre
nt2-
17O
ver-
volta
ge C
ontr
ol3-
**Re
fere
nce
/ Ra
mps
3-0*
Refe
renc
e Li
mits
3-02
Min
imum
Ref
eren
ce3-
03M
axim
um R
efer
ence
3-1*
Refe
renc
es3-
10Pr
eset
Ref
eren
ce3-
11Jo
g S
peed
[Hz]
3-14
Pres
et R
elat
ive
Refe
renc
e3-
15Re
fere
nce
1 So
urce
3-16
Refe
renc
e 2
Sour
ce3-
17Re
fere
nce
3 So
urce
3-4*
Ram
p 1
3-41
Ram
p 1
Ram
p U
p T
ime
3-42
Ram
p 1
Ram
p D
own
Tim
e3-
5*Ra
mp
23-
51Ra
mp
2 R
amp
Up
Tim
e3-
52Ra
mp
2 R
amp
Dow
n T
ime
3-8*
Oth
er R
amps
3-80
Jog
Ram
p T
ime
3-81
Qui
ck S
top
Ram
p T
ime
4-**
Lim
its /
War
ning
s4-
1*M
otor
Lim
its
4-10
Mot
or S
peed
Dire
ctio
n4-
12M
otor
Spe
ed L
ow L
imit
[Hz]
4-14
Mot
or S
peed
Hig
h L
imit
[Hz]
4-18
Curr
ent
Lim
it4-
19M
ax O
utpu
t Fr
eque
ncy
4-4*
Adj
. War
ning
s 2
4-40
War
ning
Fre
q. L
ow4-
41W
arni
ng F
req.
Hig
h4-
5*A
dj. W
arni
ngs
4-50
War
ning
Cur
rent
Low
4-51
War
ning
Cur
rent
Hig
h4-
54W
arni
ng R
efer
ence
Low
4-55
War
ning
Ref
eren
ce H
igh
4-56
War
ning
Fee
dbac
k Lo
w4-
57W
arni
ng F
eedb
ack
Hig
h4-
58M
issi
ng M
otor
Pha
se F
unct
ion
4-6*
Spee
d B
ypas
s4-
61By
pass
Spe
ed F
rom
[Hz]
4-63
Bypa
ss S
peed
To
[Hz]
4-64
Sem
i-Aut
o B
ypas
s Se
t-up
5-**
Dig
ital I
n/O
ut5-
0*D
igita
l I/O
mod
e5-
00D
igita
l Inp
ut M
ode
5-03
Dig
ital I
nput
29
Mod
e5-
1*D
igita
l Inp
uts
5-10
Term
inal
18
Dig
ital I
nput
5-11
Term
inal
19
Dig
ital I
nput
5-12
Term
inal
27
Dig
ital I
nput
5-13
Term
inal
29
Dig
ital I
nput
5-3*
Dig
ital O
utpu
ts5-
34O
n D
elay
, Dig
ital O
utpu
t5-
35O
ff D
elay
, Dig
ital O
utpu
t5-
4*Re
lays
5-40
Func
tion
Rel
ay5-
41O
n D
elay
, Rel
ay5-
42O
ff D
elay
, Rel
ay5-
5*Pu
lse
Inpu
t5-
50Te
rm. 2
9 Lo
w F
requ
ency
5-51
Term
. 29
Hig
h F
requ
ency
5-52
Term
. 29
Low
Ref
./Fee
db. V
alue
5-53
Term
. 29
Hig
h R
ef./F
eedb
. Val
ue5-
9*Bu
s Co
ntro
lled
5-90
Dig
ital &
Rel
ay B
us C
ontr
ol6-
**A
nalo
g In
/Out
6-0*
Ana
log
I/O
Mod
e6-
00Li
ve Z
ero
Tim
eout
Tim
e6-
01Li
ve Z
ero
Tim
eout
Fun
ctio
n6-
1*A
nalo
g In
put
536-
10Te
rmin
al 5
3 Lo
w V
olta
ge6-
11Te
rmin
al 5
3 H
igh
Vol
tage
6-12
Term
inal
53
Low
Cur
rent
6-13
Term
inal
53
Hig
h C
urre
nt6-
14Te
rmin
al 5
3 Lo
w R
ef./F
eedb
. Val
ue6-
15Te
rmin
al 5
3 H
igh
Ref
./Fee
db. V
alue
6-16
Term
inal
53
Filte
r Ti
me
Cons
tant
6-19
Term
inal
53
mod
e6-
2*A
nalo
g In
put
546-
20Te
rmin
al 5
4 Lo
w V
olta
ge6-
21Te
rmin
al 5
4 H
igh
Vol
tage
6-22
Term
inal
54
Low
Cur
rent
6-23
Term
inal
54
Hig
h C
urre
nt6-
24Te
rmin
al 5
4 Lo
w R
ef./F
eedb
. Val
ue6-
25Te
rmin
al 5
4 H
igh
Ref
./Fee
db. V
alue
6-26
Term
inal
54
Filte
r Ti
me
Cons
tant
6-29
Term
inal
54
mod
e6-
7*A
nalo
g/D
igita
l Out
put
456-
70Te
rmin
al 4
5 M
ode
6-71
Term
inal
45
Ana
log
Out
put
6-72
Term
inal
45
Dig
ital O
utpu
t6-
73Te
rmin
al 4
5 O
utpu
t M
in S
cale
6-74
Term
inal
45
Out
put
Max
Sca
le6-
76Te
rmin
al 4
5 O
utpu
t Bu
s Co
ntro
l6-
9*A
nalo
g/D
igita
l Out
put
426-
90Te
rmin
al 4
2 M
ode
6-91
Term
inal
42
Ana
log
Out
put
6-92
Term
inal
42
Dig
ital O
utpu
t6-
93Te
rmin
al 4
2 O
utpu
t M
in S
cale
6-94
Term
inal
42
Out
put
Max
Sca
le6-
96Te
rmin
al 4
2 O
utpu
t Bu
s Co
ntro
l6-
98D
rive
Type
8-**
Com
m. a
nd O
ptio
ns8-
0*G
ener
al S
ettin
gs8-
01Co
ntro
l Site
8-02
Cont
rol S
ourc
e8-
03Co
ntro
l Tim
eout
Tim
e8-
04Co
ntro
l Tim
eout
Fun
ctio
n8-
3*FC
Por
t Se
ttin
gs8-
30Pr
otoc
ol8-
31A
ddre
ss8-
32Ba
ud R
ate
8-33
Parit
y /
Stop
Bits
8-35
Min
imum
Res
pons
e D
elay
8-36
Max
imum
Res
pons
e D
elay
8-37
Max
imum
Inte
r-ch
ar d
elay
8-4*
FC M
C p
roto
col s
et8-
43PC
D R
ead
Con
figur
atio
n8-
5*D
igita
l/Bus
8-50
Coas
ting
Sel
ect
8-51
Qui
ck S
top
Sel
ect
8-52
DC
Bra
ke S
elec
t8-
53St
art
Sele
ct8-
54Re
vers
ing
Sel
ect
8-55
Set-
up S
elec
t8-
56Pr
eset
Ref
eren
ce S
elec
t8-
7*BA
Cnet
8-70
BACn
et D
evic
e In
stan
ce8-
72M
S/TP
Max
Mas
ters
8-73
MS/
TP M
ax In
fo F
ram
es8-
74"I
am
" Se
rvic
e8-
75In
tialis
atio
n P
assw
ord
8-8*
FC P
ort
Dia
gnos
tics
8-80
Bus
Mes
sage
Cou
nt8-
81Bu
s Er
ror
Coun
t8-
82Sl
ave
Mes
sage
s Rc
vd8-
83Sl
ave
Erro
r Co
unt
8-84
Slav
e M
essa
ges
Sent
8-85
Slav
e Ti
meo
ut E
rror
s8-
88Re
set
FC p
ort
Dia
gnos
tics
8-9*
Bus
Feed
back
8-94
Bus
Feed
back
113
-**
Smar
t Lo
gic
13-0
*SL
C S
ettin
gs13
-00
SL C
ontr
olle
r M
ode
13-0
1St
art
Even
t13
-02
Stop
Eve
nt13
-03
Rese
t SL
C13
-1*
Com
para
tors
13-1
0Co
mpa
rato
r O
pera
nd13
-11
Com
para
tor
Ope
rato
r13
-12
Com
para
tor
Valu
e13
-2*
Tim
ers
13-2
0SL
Con
trol
ler
Tim
er13
-4*
Logi
c Ru
les
13-4
0Lo
gic
Rule
Boo
lean
113
-41
Logi
c Ru
le O
pera
tor
113
-42
Logi
c Ru
le B
oole
an 2
13-4
3Lo
gic
Rule
Ope
rato
r 2
13-4
4Lo
gic
Rule
Boo
lean
313
-5*
Stat
es13
-51
SL C
ontr
olle
r Ev
ent
13-5
2SL
Con
trol
ler
Act
ion
14-*
*Sp
ecia
l Fun
ctio
ns14
-0*
Inve
rter
Sw
itchi
ng14
-01
Switc
hing
Fre
quen
cy14
-03
Ove
rmod
ulat
ion
14-0
8D
ampi
ng G
ain
Fac
tor
14-1
*M
ains
On/
Off
14-1
0M
ains
Fai
lure
14-1
2Fu
nctio
n a
t M
ains
Imba
lanc
e14
-2*
Rese
t Fu
nctio
ns14
-20
Rese
t M
ode
14-2
1A
utom
atic
Res
tart
Tim
e14
-22
Ope
ratio
n M
ode
14-2
3Ty
peco
de S
ettin
g14
-27
Act
ion
At
Inve
rter
Fau
lt14
-28
Prod
uctio
n S
ettin
gs14
-29
Serv
ice
Code
14-4
*En
ergy
Opt
imis
ing
14-4
0VT
Lev
el14
-41
AEO
Min
imum
Mag
netis
atio
n14
-5*
Envi
ronm
ent
14-5
0RF
I Filt
er14
-51
DC-
Link
Vol
tage
Com
pens
atio
n14
-52
Fan
Con
trol
14-5
3Fa
n M
onito
r14
-55
Out
put
Filte
r14
-6*
Aut
o D
erat
e14
-63
Min
Sw
itch
Fre
quen
cy15
-**
Driv
e In
form
atio
n15
-0*
Ope
ratin
g D
ata
15-0
0O
pera
ting
hou
rs15
-01
Runn
ing
Hou
rs15
-02
kWh
Cou
nter
15-0
3Po
wer
Up'
s15
-04
Ove
r Te
mp'
s15
-05
Ove
r Vo
lt's
15-0
6Re
set
kWh
Cou
nter
Quick Guide VLT® HVAC Basic Drive Quick Guide
30 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
15-0
7Re
set
Runn
ing
Hou
rs C
ount
er15
-3*
Ala
rm L
og15
-30
Ala
rm L
og: E
rror
Cod
e15
-31
Inte
rnal
Faul
tRea
son
15-4
*D
rive
Iden
tific
atio
n15
-40
FC T
ype
15-4
1Po
wer
Sec
tion
15-4
2Vo
ltage
15-4
3So
ftw
are
Vers
ion
15-4
4O
rder
ed T
ypeC
ode
15-4
6D
rive
Ord
erin
g N
o15
-47
Pow
er C
ard
Ord
erin
g N
o15
-48
LCP
Id N
o15
-49
SW ID
Con
trol
Car
d15
-50
SW ID
Pow
er C
ard
15-5
1D
rive
Seria
l Num
ber
15-5
3Po
wer
Car
d S
eria
l Num
ber
15-9
*Pa
ram
eter
Info
15-9
2D
efin
ed P
aram
eter
s15
-97
App
licat
ion
Typ
e15
-98
Driv
e Id
entif
icat
ion
16-*
*D
ata
Read
outs
16-0
*G
ener
al S
tatu
s16
-00
Cont
rol W
ord
16-0
1Re
fere
nce
[Uni
t]16
-02
Refe
renc
e [%
]16
-03
Stat
us W
ord
16-0
5M
ain
Act
ual V
alue
[%]
16-0
9Cu
stom
Rea
dout
16-1
*M
otor
Sta
tus
16-1
0Po
wer
[kW
]16
-11
Pow
er [h
p]16
-12
Mot
or V
olta
ge16
-13
Freq
uenc
y16
-14
Mot
or c
urre
nt16
-15
Freq
uenc
y [%
]16
-18
Mot
or T
herm
al16
-3*
Driv
e St
atus
16-3
0D
C L
ink
Volta
ge16
-34
Hea
tsin
k Te
mp.
16-3
5In
vert
er T
herm
al16
-36
Inv.
Nom
. Cur
rent
16-3
7In
v. M
ax. C
urre
nt16
-38
SL C
ontr
olle
r St
ate
16-5
*Re
f. &
Fee
db.
16-5
0Ex
tern
al R
efer
ence
16-5
2Fe
edba
ck[U
nit]
16-6
*In
puts
& O
utpu
ts16
-60
Dig
ital I
nput
16-6
1Te
rmin
al 5
3 Se
ttin
g16
-62
Ana
log
Inpu
t A
I53
16-6
3Te
rmin
al 5
4 Se
ttin
g16
-64
Ana
log
Inpu
t A
I54
16-6
5A
nalo
g O
utpu
t A
O42
[mA
]16
-66
Dig
ital O
utpu
t16
-67
Puls
e In
put
#29
[Hz]
16-7
1Re
lay
Out
put
[bin
]16
-72
Coun
ter
A16
-73
Coun
ter
B
16-7
9A
nalo
g O
utpu
t A
O45
16-8
*Fi
eldb
us &
FC
Por
t16
-86
FC P
ort
REF
116
-9*
Dia
gnos
is R
eado
uts
16-9
0A
larm
Wor
d16
-91
Ala
rm W
ord
216
-92
War
ning
Wor
d16
-93
War
ning
Wor
d 2
16-9
4Ex
t. S
tatu
s W
ord
16-9
5Ex
t. S
tatu
s W
ord
218
-**
Info
& R
eado
uts
18-1
*Fi
re M
ode
Log
18-1
0Fi
reM
ode
Log:
Even
t20
-**
Driv
e Cl
osed
Loo
p20
-0*
Feed
back
20-0
0Fe
edba
ck 1
Sou
rce
20-0
1Fe
edba
ck 1
Con
vers
ion
20-8
*PI
Bas
ic S
ettin
gs20
-81
PI N
orm
al/
Inve
rse
Cont
rol
20-8
3PI
Sta
rt S
peed
[Hz]
20-8
4O
n R
efer
ence
Ban
dwid
th20
-9*
PI C
ontr
olle
r20
-91
PI A
nti W
indu
p20
-93
PI P
ropo
rtio
nal G
ain
20-9
4PI
Inte
gral
Tim
e20
-97
PI F
eed
For
war
d F
acto
r22
-**
App
l. Fu
nctio
ns22
-4*
Slee
p M
ode
22-4
0M
inim
um R
un T
ime
22-4
1M
inim
um S
leep
Tim
e22
-43
Wak
e-U
p S
peed
[Hz]
22-4
4W
ake-
Up
Ref
./FB
Diff
22-4
5Se
tpoi
nt B
oost
22-4
6M
axim
um B
oost
Tim
e22
-47
Slee
p S
peed
[Hz]
22-6
*Br
oken
Bel
t D
etec
tion
22-6
0Br
oken
Bel
t Fu
nctio
n22
-61
Brok
en B
elt
Torq
ue22
-62
Brok
en B
elt
Del
ay24
-**
App
l. Fu
nctio
ns 2
24-0
*Fi
re M
ode
24-0
0FM
Fun
ctio
n24
-05
FM P
rese
t Re
fere
nce
24-0
9FM
Ala
rm H
andl
ing
24-1
*D
rive
Bypa
ss24
-10
Driv
e By
pass
Fun
ctio
n24
-11
Driv
e By
pass
Del
ay T
ime
38-*
*D
ebug
onl
y -
see
PNU
142
9 (s
ervi
ce-
code
) al
so38
-0*
All
debu
g p
aram
eter
s38
-00
Test
Mon
itorM
ode
38-0
1Ve
rsio
n A
nd S
tack
38-0
2Pr
otoc
ol S
W v
ersi
on38
-06
LCPE
dit
Set-
up38
-07
EEPR
OM
Dda
taVe
rs38
-08
Pow
erD
ataV
aria
ntID
38-0
9A
MA
Ret
ry38
-10
DA
C s
elec
tion
38-1
2D
AC
sca
le
38-2
0M
OC_
Test
US1
638
-21
MO
C_Te
stS1
638
-23
Test
Moc
Func
tions
38-2
4D
C L
ink
Pow
er M
easu
rem
ent
38-2
5Ch
eckS
um38
-30
Ana
log
Inpu
t 53
(%)
38-3
1A
nalo
g In
put
54 (%
)38
-32
Inpu
t Re
fere
nce
138
-33
Inpu
t Re
fere
nce
238
-34
Inpu
t Re
fere
nce
Sett
ing
38-3
5Fe
edba
ck (%
)38
-36
Faul
t Co
de38
-37
Cont
rol W
ord
38-3
8Re
setC
ount
ersC
ontr
ol38
-39
Act
ive
Setu
p F
or B
ACn
et38
-40
Nam
e O
f A
nalo
g V
alue
1 F
or B
ACn
et38
-41
Nam
e O
f A
nalo
g V
alue
3 F
or B
ACn
et38
-42
Nam
e O
f A
nalo
g V
alue
5 F
or B
ACn
et38
-43
Nam
e O
f A
nalo
g V
alue
6 F
or B
ACn
et38
-44
Nam
e O
f Bi
nary
Val
ue 1
For
BA
Cnet
38-4
5N
ame
Of
Bina
ry V
alue
2 F
or B
ACn
et38
-46
Nam
e O
f Bi
nary
Val
ue 3
For
BA
Cnet
38-4
7N
ame
Of
Bina
ry V
alue
4 F
or B
ACn
et38
-48
Nam
e O
f Bi
nary
Val
ue 5
For
BA
Cnet
38-4
9N
ame
Of
Bina
ry V
alue
6 F
or B
ACn
et38
-50
Nam
e O
f Bi
nary
Val
ue 2
1 Fo
r BA
Cnet
38-5
1N
ame
Of
Bina
ry V
alue
22
For
BACn
et38
-52
Nam
e O
f Bi
nary
Val
ue 3
3 Fo
r BA
Cnet
38-5
3Bu
s Fe
edba
ck 1
Con
vers
ion
38-5
4Ru
n S
top
Bus
Con
trol
38-5
8In
vert
er E
TR c
ount
er38
-59
Rect
ifier
ETR
cou
nter
38-6
0D
B_Er
rorW
arni
ngs
38-6
1Ex
tend
ed A
larm
Wor
d38
-69
AM
A_D
ebug
S32
38-7
4A
OCD
ebug
038
-75
AO
CDeb
ug1
38-7
6A
O42
_Fix
edM
ode
38-7
7A
O42
_Fix
edVa
lue
38-7
8D
I_Te
stCo
unte
rs38
-79
Prot
ect
Func
. Cou
nter
38-8
0H
ighe
st L
owes
t Co
uple
38-8
1D
B_Se
ndD
ebug
Cmd
38-8
2M
axTa
skRu
nnin
gTim
e38
-83
Deb
ugIn
form
atio
n38
-85
DB_
Opt
ionS
elec
tor
38-8
6EE
PRO
M_A
ddre
ss38
-87
EEPR
OM
_Val
ue38
-88
Logg
er T
ime
Rem
ain
38-9
0LC
P F
C-Pr
otoc
ol s
elec
t38
-91
Mot
or P
ower
Inte
rnal
38-9
2M
otor
Vol
tage
Inte
rnal
38-9
3M
otor
Fre
quen
cy In
tern
al38
-94
Lsig
ma
38-9
5D
B_Si
mul
ateA
larm
War
ning
ExSt
atus
38-9
6D
ata
Logg
er P
assw
ord
38-9
7D
ata
Logg
ing
Per
iod
38-9
8Si
gnal
to
Deb
ug38
-99
Sign
ed D
ebug
Info
40-*
*D
ebug
onl
y -
Back
up40
-0*
Deb
ug p
aram
eter
s ba
ckup
40-0
0Te
stM
onito
rMod
e_Ba
ckup
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 31
1 1
Downloaded from www.Manualslib.com manuals search engine
1.6 Warnings and Alarms
Faultnumber
Alarm/Warning
BitNumber Fault text Warning Alarm
Triplocked Cause of problem
2 16 Live zero error X X
Signal on terminal 53 or 54 is less than 50% of value set in6-10 Terminal 53 Low Voltage, 6-12 Terminal 53 Low Current,6-20 Terminal 54 Low Voltageor 6-22 Terminal 54 Low Current. Seealso parameter group 6-0*
4 14 Mains ph. loss X X XMissing phase on supply side or too high voltage imbalance. Checksupply voltage. See 14-12 Function at Mains Imbalance
7 11 DC over volt X X Intermediate circuit voltage exceeds limit.
8 10 DC under volt X X Intermediate circuit voltage drops below “voltage warning low”limit.
9 9Inverteroverload X X More than 100% load for too long.
10 8Motor ETRover X X
Motor is too hot due to more than 100% load for too long. See1-90 Motor Thermal Protection
11 7 Motor th over X X Thermistor or thermistor connection is disconnected. See1-90 Motor Thermal Protection.
13 5 Over Current X X X Inverter peak current limit is exceeded.
14 2 Earth Fault X X Discharge from output phases to ground.
16 12 Short Circuit X X Short-circuit in motor or on motor terminals.
17 4 Ctrl. word TO X X No communication to frequency converter. See parameter group8-0*
24 50 Fan Fault X X The fan is not working (Only on 400 V 30-90 kW units).
30 19 U phase loss X XMotor phase U is missing. Check the phase. See 4-58 Missing MotorPhase Function.
31 20 V phase loss X XMotor phase V is missing. Check the phase. See 4-58 Missing MotorPhase Function.
32 21 W phase loss X XMotor phase W is missing. Check the phase. See 4-58 Missing MotorPhase Function.
38 17 Internal fault X X Contact the local Danfoss supplier.
44 28 Earth Fault X X Discharge from output phases to ground.
47 23ControlVoltage Fault X X X 24 V DC may be overloaded.
48 25VDD1 SupplyLow X X Control voltage low. Contact the local Danfoss supplier
50 Calibrationfailed X Contact the local Danfoss supplier.
51 15 Unom,Inom X The setting of motor voltage, motor current and motor power ispresumably wrong. Check the settings.
52 low Inom X The motor current is too low. Check the settings.
53 big motor X The motor is too big for the to be carried out
54 small mot X The motor is too small for the to be carried out
55 par. range X The parameter values found from the motor are outside acceptablerange
56 user interrupt X The has been interrupted by the user
Quick Guide VLT® HVAC Basic Drive Quick Guide
32 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Faultnumber
Alarm/Warning
BitNumber Fault text Warning Alarm
Triplocked Cause of problem
57 timeout X
Try to start the again a number of times, until the is carried out.
NOTERepeated runs may heat the motor to a level where theresistance Rs and Rr are increased. In most cases, however,this is not critical
58 internal X X Contact the local Danfoss supplier.
59 25 Current limit X The current is higher than the value in 4-18 Current Limit
60 44ExternalInterlock X
External interlock has been activated. To resume normal operation,apply 24 V DC to the terminal programmed for external interlockand reset the frequency converter (via serial communication, digitalI/O, or by pressing reset button on keypad).
66 26
Heat sinkTemperatureLow X
This warning is based on the temperature sensor in the IGBTmodule (Only on 400 V 30-90 kW units).
69 1Pwr. CardTemp X X X
The temperature sensor on the power card is either too hot or toocold.
79
Illegal powersection config-uration X X Internal fault. Contact the local Danfoss supplier.
80 29Driveinitialised X All parameter settings are initialized to default settings.
87 47Auto DCBraking X The drive is auto DC braking
95 40 Broken Belt X X Torque is below the torque level set for no load, indicating abroken belt. See parameter group 22-6*.
126 Motor Rotating X High back-emf voltage. Stop the motor of the PM motor.
200 Fire Mode X Fire mode has been activated
202
Fire ModeLimitsExceeded X Fire Mode has suppressed one or more warranty voiding alarms
250 New sparepart X XThe power or switch mode power supply has been exchanged.(Only on 400 V 30-90 kW units). Contact the local Danfoss supplier
251 New Typecode X XThe frequency converter has a new type code (Only on 400 V 30-90kW units). Contact the local Danfoss supplier.
Table 1.29
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 33
1 1
Downloaded from www.Manualslib.com manuals search engine
1.7 General Specifications
1.7.1 Mains Supply 3x200-240 V AC
Frequency converter PK25
PK37
PK75
P1K5
P2K2 P3K7 P5K5 P7K5 P11K P15K P18K P22K P30K P37K P45K
Typical shaft output [kW] 0.25 0.37 0.75 1.5 2.2 3.7 5.5 7.5 11.0 15.0 18.5 22.0 30.0 37.0 45.0
Typical shaft output [hp] 0.33 0.5 1.0 2.0 3.0 5.0 7.5 10.0 15.0 20.0 25.0 30.0 40.0 50.0 60.0
IP20 frame H1 H1 H1 H1 H2 H3 H4 H4 H5 H6 H6 H7 H7 H8 H8
Max. cable size in terminals (mains,
motor) [mm2/AWG]
4/10 4/10 4/10 4/10 4/10 4/10 16/6 16/6 16/6 35/2 35/2 50/1 50/1 95/0 120/(4/0)
Output current
RELAY 2
130B
B632
.10 40 °C ambient temperature
Continuous(3x200-240 V) [A]
1.5 2.2 4.2 6.8 9.6 15.2 22.0 28.0 42.0 59.4 74.8 88.0 115.0 143.0 170.0
Intermittent(3x200-240 V) [A]
1.7 2.4 4.6 7.5 10.6 16.7 24.2 30.8 46.2 65.3 82.3 96.8 126.5 157.3 187.0
Max. input current
RELAY 2
130B
B633
.10 Continuous
(3x200-240 V) [A]1.1 1.6 2.8 5.6 8.6/
7.214.1/12.0
21.0/18.0
28.3/24.0
41.0/38.2
52.7 65.0 76.0 103.7 127.9 153.0
Intermittent(3x200-240 V) [A]
1.2 1.8 3.1 6.2 9.5/7.9
15.5/13.2
23.1/19.8
31.1/26.4
45.1/42.0
58.0 71.5 83.7 114.1 140.7 168.3
Max. mains fuses See 1.3.6 Fuses
Estimated powerloss [W], Best
case/typical1)
12/14
15/18
21/26
48/60
80/102
97/120
182/204
229/268
369/386
512 697 879 1149 1390 1500
Weight enclosureIP20 [kg]
2. 2.0 2.0 2.1 3.4 4.5 7.9 7.9 9.5 24.5 24.5 36.0 36.0 51.0 51.0
Efficiency [%],Best case/
Typical1)
97.0/
96.5
97.3/
96.8
98.0/
97.6
97.6/
97.0
97.1/96.3
97.9/97.4
97.3/97.0
98.5/97.1
97.2/97.1
97.0 97.1 96.8 97.1 97.1 97.3
Output current
50 °C ambient temperature
Continuous(3x200-240 V) [A]
1.5 1.9 3.5 6.8 9.6 13.0 19.8 23.0 33.0 53.5 66.6 79.2 103.5 128.7 153.0
Intermittent(3x200-240 V) [A]
1.7 2.1 3.9 7.5 10.6 14.3 21.8 25.3 36.3 58.9 73.3 87.1 113.9 141.6 168.3
Table 1.30
1) At rated load conditions
Quick Guide VLT® HVAC Basic Drive Quick Guide
34 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.7.2 Mains Supply 3x380-480 V ACFr
eque
ncy
conv
erte
rPK
37PK
75P1
K5P2
K2P3
K0P4
K0P5
K5P7
K5P1
1KP1
5KP1
8KP2
2KP3
0KP3
7KP4
5KP5
5KP7
5KP9
0KTy
pica
l sha
ft o
utpu
t [k
W]
0.37
0.75
1.5
2.2
3.0
4.0
5.5
7.5
11.0
15.0
18.5
22.0
30.0
37.0
45.0
55.0
75.0
90.0
Typi
cal s
haft
out
put
[hp]
0.5
1.0
2.0
3.0
4.0
5.0
7.5
10.0
15.0
20.0
25.0
30.0
40.0
50.0
60.0
70.0
100.
012
5.0
IP20
fram
eH
1H
1H
1H
2H
2H
2H
3H
3H
4H
4H
5H
5H
6H
6H
6H
7H
7H
8
Max
. cab
le s
ize
in t
erm
inal
s (m
ains
, mot
or)
[mm
2 /AW
G]
4/10
4/10
4/10
4/10
4/10
4/10
4/10
4/10
16/6
16/6
16/6
16/6
35/2
35/2
35/2
50/1
95/0
120/
250M
CM
Out
put
curr
ent
RELA
Y 2
130BB632.10
40 °C
am
bien
t te
mpe
ratu
re
Cont
inuo
us(3
x380
-440
V)
[A]
1.2
2.2
3.7
5.3
7.2
9.0
12.0
15.5
23.0
31.0
37.0
42.5
61.0
73.0
90.0
106.
014
7.0
177.
0
Inte
rmitt
ent
(3x3
80-4
40 V
)[A
]
1.3
2.4
4.1
5.8
7.9
9.9
13.2
17.1
25.3
34.0
40.7
46.8
67.1
80.3
99.0
116.
016
1.0
194.
0
Cont
inuo
us(3
x440
-480
V)
[A]
1.1
2.1
3.4
4.8
6.3
8.2
11.0
14.0
21.0
27.0
34.0
40.0
52.0
65.0
80.0
105.
013
0.0
160.
0
Inte
rmitt
ent
(3x4
40-4
80 V
)[A
]
1.2
2.3
3.7
5.3
6.9
9.0
12.1
15.4
23.1
29.7
37.4
44.0
57.2
71.5
88.0
115.
014
3.0
176.
0
Max
. inp
ut c
urre
nt
RELA
Y 2
130BB633.10
Cont
inuo
us(3
x380
-440
V)
[A]
1.2
2.1
3.5
4.7
6.3
8.3
11.2
15.1
22.1
29.9
35.2
41.5
57.0
70.0
84.0
103.
014
0.0
166.
0
Inte
rmitt
ent
(3x3
80-4
40 V
)[A
]
1.3
2.3
3.9
5.2
6.9
9.1
12.3
16.6
24.3
32.9
38.7
45.7
62.7
77.0
92.4
113.
015
4.0
182.
0
Cont
inuo
us(3
x440
-480
V)
[A]
1.0
1.8
2.9
3.9
5.3
6.8
9.4
12.6
18.4
24.7
29.3
34.6
49.2
60.6
72.5
88.6
120.
914
2.7
Inte
rmitt
ent
(3x4
40-4
80 V
)[A
]
1.1
2.0
3.2
4.3
5.8
7.5
10.3
13.9
20.2
27.2
32.2
38.1
54.1
66.7
79.8
97.5
132.
915
7.0
Max
. mai
ns fu
ses
See
1.3.
6 Fu
ses
Tabl
e 1.
31
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 35
1 1
Downloaded from www.Manualslib.com manuals search engine
Freq
uenc
y co
nver
ter
PK37
PK75
P1K5
P2K2
P3K0
P4K0
P5K5
P7K5
P11K
P15K
P18K
P22K
P30K
P37K
P45K
P55K
P75K
P90K
Estim
ated
pow
er lo
ss [W
], Be
st c
ase/
typi
cal1)
13/1
516
/21
46/5
746
/58
66/8
395
/118
104/
131
159/
198
248/
274
353/
379
412/
456
475/
523
733
922
1067
1133
1733
2141
Wei
ght
encl
osur
e IP
20 [k
g]2.
02.
02.
13.
33.
33.
44.
34.
57.
97.
99.
59.
524
.524
.524
.536
.036
.051
.0
Effic
ienc
y [%
], Be
st c
ase/
Typi
cal 1
97.8
/97.
398
.0/9
7.6
97.7
/97
.298
.3/9
7.9
98.2
/97.
898
.0/9
7.6
98.4
/98
.098
.2/9
7.8
98.1
/97.
998
.0/9
7.8
98.1
/97.
998
.1/9
7.9
97.8
97.7
9898
.297
.897
.9
Out
put
curr
ent
50
°C a
mbi
ent
tem
pera
ture
Cont
inuo
us(3
x380
-440
V)
[A]
1.04
1.93
3.7
4.85
6.3
8.4
10.9
14.0
20.9
28.0
34.1
38.0
48.8
58.4
72.0
74.2
102.
912
3.9
Inte
rmitt
ent
(3x3
80-4
40 V
)[A
]
1.1
2.1
4.07
5.4
6.9
9.2
12.0
15.4
23.0
30.8
37.5
41.8
53.7
64.2
79.2
81.6
113.
213
6.3
Cont
inuo
us(3
x440
-480
V)
[A]
1.0
1.8
3.4
4.4
5.5
7.5
10.0
12.6
19.1
24.0
31.3
35.0
41.6
52.0
64.0
73.5
91.0
112.
0
Inte
rmitt
ent
(3x4
40-4
80 V
)[A
]
1.1
2.0
3.7
4.8
6.1
8.3
11.0
13.9
21.0
26.4
34.4
38.5
45.8
57.2
70.4
80.9
100.
112
3.2
Tabl
e 1.
32
Quick Guide VLT® HVAC Basic Drive Quick Guide
36 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.7.3 Mains Supply 3x380-480 V ACFr
eque
ncy
conv
erte
rPK
75P1
K5P2
K2P3
K0P4
KOP5
K5P7
K5P1
1KP1
5KP1
8KP1
1KP1
5KP1
8KP2
2KP3
0KP3
7KP4
5KP5
5KP7
5KP9
0KTy
pica
l sha
ft o
utpu
t [k
W]
0.75
1.5
2.2
3.0
4.0
5.5
7.5
1115
18.5
1115
18.5
22.0
30.0
37.0
45.0
55.0
75.0
90.0
Typi
cal s
haft
out
put
[hp]
1.0
2.0
3.0
4.0
5.0
7.5
10.0
1520
2515
.020
25.0
30.0
40.0
50.0
60.0
70.0
100.
012
5.0
IP54
fram
eI2
I2I2
I2I2
I3I3
I4I4
I4I5
I5I5
I6I6
I6I7
I7I8
I8
Max
. cab
le s
ize
in t
erm
inal
s (m
ains
,
mot
or)
[mm
2 /AW
G]
4/10
4/10
4/10
4/10
4/10
4/10
4/10
16/6
16/6
16/6
10/7
10/7
10/7
35/2
35/2
35/2
50/1
50/1
95/
(3/0
)12
0/(4
/0)
Out
put
curr
ent
40
°C a
mbi
ent
tem
pera
ture
Cont
inuo
us(3
x380
-440
V)
[A]
2.2
3.7
5.3
7.2
9.0
12.0
15.5
23.0
31.0
37.0
2432
37.5
44.0
61.0
73.0
90.0
106.
014
7.0
177.
0
Inte
rmitt
ent
(3x3
80-4
40 V
)[A
]
2.4
4.1
5.8
7.9
9.9
13.2
17.1
25.3
34.0
40.7
26.2
35.2
41.3
48.4
67.1
80.3
99.0
116.
616
1.7
194.
7
Cont
inuo
us(3
x440
-480
V)
[A]
2.1
3.4
4.8
6.3
8.2
11.0
14.0
21.0
27.0
34.0
2127
3440
.052
.065
.080
.010
5.0
130.
016
0.0
Inte
rmitt
ent
(3x4
40-4
80 V
)[A
]
2.3
3.7
5.3
6.9
9.0
12.1
15.4
23.1
29.7
37.4
23.1
29.7
37.4
44.0
57.2
71.5
88.0
115.
514
3.0
176.
0
Max
. inp
ut c
urre
nt
Co
ntin
uous
(3x3
80-4
40 V
)[A
]
2.1
3.5
4.7
6.3
8.3
11.2
15.1
22.1
29.9
35.2
2229
3441
.857
.070
.384
.210
2.9
140.
316
5.6
Inte
rmitt
ent
(3x3
80-4
40 V
)[A
]
2.3
3.9
5.2
6.9
9.1
12.3
16.6
24.3
32.9
38.7
24.2
31.9
37.3
46.0
62.7
77.4
92.6
113.
115
4.3
182.
2
Cont
inuo
us(3
x440
-480
V)
[A]
1.8
2.9
3.9
5.3
6.8
9.4
12.6
18.4
24.7
29.3
1925
3136
.049
.260
.672
.588
.612
0.9
142.
7
Inte
rmitt
ent
(3x
440-
480
V)[A
]
2.0
3.2
4.3
5.8
7.5
10.3
13.9
20.2
27.2
32.2
20.9
27.5
34.1
39.6
54.1
66.7
79.8
97.5
132.
915
7.0
Max
. mai
ns fu
ses
See
1.3.
6 Fu
ses
Tabl
e 1.
33
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 37
1 1
Downloaded from www.Manualslib.com manuals search engine
Freq
uenc
y co
nver
ter
PK75
P1K5
PK2K
2PK
3K OPK
4K OPK
5K 5PK
7K 5P1
1KP1
5KP1
8KPK
11 KPK
15 KP1
8KP2
2KP3
0KP3
7KP4
5KP5
5KP7
5KP9
0K
Estim
ated
pow
er lo
ss [W
], Be
st c
ase/
typi
cal1)
21/
1646
/57
46/
5866
/83
95/
118
104/
131
159/
198
248/
274
353/
379
412/
456
242
330
396
496
734
995
840
1099
1520
1781
Wei
ght
encl
osur
e IP
54 [k
g]5.
35.
35.
35.
35.
37.
27.
213
.813
.813
.823
2323
2727
2745
4565
65
Effic
ienc
y [%
], Be
st c
ase/
Typi
cal 1
98.0
/97
.697
.7/
97.2
98.3
/97
.998
.2/
97.8
98.0
/97
.698
.4/
98.0
98.2
/97
.898
.1/
97.9
98.0
/97
.898
.1/
97.9
98.0
98.0
98.0
98.0
97.8
97.6
98.3
98.2
98.1
98.3
Out
put
curr
ent
50
°C a
mbi
ent
tem
pera
ture
Cont
inuo
us(3
x380
-440
V)
[A]
1.93
3.7
4.85
6.3
7.5
10.9
14.0
20.9
28.0
33.0
19.2
25.6
3035
.248
.858
.463
.074
.210
2.9
123.
9
Inte
rmitt
ent
(3x3
80-4
40 V
) [A
]2.
14.
075.
46.
99.
212
.015
.423
.030
.836
.321
.228
.233
38.7
53.9
64.2
69.3
81.6
113.
213
6.3
Cont
inuo
us(3
x440
-480
V)
[A]
1.8
3.4
4.4
5.5
6.8
10.0
12.6
19.1
24.0
30.0
16.8
21.6
27.2
32.0
41.6
52.0
56.0
73.5
91.0
112.
0
Inte
rmitt
ent
(3x4
40-4
80 V
) [A
]2.
03.
74.
86.
18.
311
.013
.921
.026
.433
.018
.523
.830
35.2
45.8
57.2
61.6
80.9
100.
112
3.2
Tabl
e 1.
34
Quick Guide VLT® HVAC Basic Drive Quick Guide
38 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
1.7.4 Mains Supply 3x525-600 V AC
Frequency converter P2K2 P3K0 P3K7 P5K5 P7K5 P11K P15K P18K P22K P30K P37K P45K P55K P75K P90K
Typical shaft output [kW] 2.2 3.0 3.7 5.5 7.5 11.0 15.0 18.5 22.0 30.0 37 45.0 55.0 75.0 90.0
Typical shaft output [hp] 3.0 4.0 5.0 7.5 10.0 15.0 20.0 25.0 30.0 40.0 50.0 60.0 70.0 100.0
125.0
IP20 frame H9 H9 H9 H9 H9 H10 H10 H6 H6 H6 H7 H7 H7 H8 H8
Max. cable size in terminals (mains,
motor) [mm2/AWG]
4/10 4/10 4/10 4/10 4/10 10/8 10/8 35/2 35/2 35/2 50/1 50/1 50/1 95/0 120/(4/0)
Output current
RELAY 2
130B
B632
.10 40 °C ambient temperature
Continuous(3x525-550 V)[A]
4.1 5.2 6.4 9.5 11.5 19.0 23.0 28.0 36.0 43.0 54.0 65.0 87.0 105.0
137.0
Intermittent(3x525-550 V)[A]
4.5 5.7 7.0 10.5 12.7 20.9 25.3 30.8 39.6 47.3 59.4 71.5 95.7 115.5
150.7
Continuous(3x551-600 V)[A]
3.9 4.9 6.1 9.0 11.0 18.0 22.0 27.0 34.0 41.0 52.0 62.0 83.0 100.0
131.0
Intermittent(3x551-600 V)[A]
4.3 5.4 6.7 9.9 12.1 19.8 24.2 29.7 37.4 45.1 57.2 68.2 91.3 110.0
144.1
Max. input current
RELAY 2
130B
B633
.10 Continuous
(3x525-550 V)[A]
3.7 5.1 5.0 8.7 11.9 16.5 22.5 27.0 33.1 45.1 54.7 66.5 81.3 109.0
130.9
Intermittent(3x525-550 V)[A]
4.1 5.6 6.5 9.6 13.1 18.2 24.8 29.7 36.4 49.6 60.1 73.1 89.4 119.9
143.9
Continuous(3x551-600 V)[A]
3.5 4.8 5.6 8.3 11.4 15.7 21.4 25.7 31.5 42.9 52.0 63.3 77.4 103.8
124.5
Intermittent(3x551-600 V)[A]
3.9 5.3 6.2 9.2 12.5 17.3 23.6 28.3 34.6 47.2 57.2 69.6 85.1 114.2
137.0
Max. mains fuses See 1.3.6 Fuses
Estimated power loss [W], Best case/
typical1)
65 90 110 132 180 216 294 385 458 542 597 727 1092 1380 1658
Weight enclosure IP54 kg] 6.6 6.6 6.6 6.6 6.6 11.5 11.5 24.5 24.5 24.5 36.0 36.0 36.0 51.0 51.0
Efficiency [%], Best case/Typical 1 97.9 97 97.9 98.1 98.1 98.4 98.4 98.4 98.4 98.5 98.5 98.7 98.5 98.5 98.5
Output current
50 °C ambient temperature
Continuous(3x525-550 V)[A]
2.9 3.6 4.5 6.7 8.1 13.3 16.1 19.6 25.2 30.1 37.8 45.5 60.9 73.5 95.9
Intermittent(3x525-550 V)[A]
3.2 4.0 4.9 7.4 8.9 14.6 17.7 21.6 27.7 33.1 41.6 50.0 67.0 80.9 105.5
Continuous(3x551-600 V)[A]
2.7 3.4 4.3 6.3 7.7 12.6 15.4 18.9 23.8 28.7 36.4 43.3 58.1 70.0 91.7
Intermittent(3x551-600 V)[A]
3.0 3.7 4.7 6.9 8.5 13.9 16.9 20.8 26.2 31.6 40.0 47.7 63.9 77.0 100.9
Table 1.35
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 39
1 1
Downloaded from www.Manualslib.com manuals search engine
1.7.5 EMC Test Results
The following test results have been obtained using asystem with a frequency converter, a screened controlcable, a control box with potentiometer, as well as a motorscreened cable.
RFI Filter Type Conduct emission. Maximum shielded cable length [m] Radiated emission
Industrial environmentHousing, trades and
light industriesIndustrial environment
Housing, trades andlight industries
EN 55011 Class A2 EN 55011 Class A1 EN 55011 Class B EN 55011 Class A1 EN 55011 Class B
Withoutexternal
filter
Withexternal
filter
Withoutexternal
filter
Withexternal
filter
Withoutexternal
filter
Withexternal
filter
Withoutexternal
filter
Withexternal
filter
Withoutexternal
filter
Withexternal
filter
H4 RFI filter (Class A1)
0.25-11 kW3x200-240 VIP20
25 50 20 Yes Yes No
0.37-22 kW3x380-480 VIP20
25 50 20 Yes Yes No
H2 RFI filter (Class A2)
1.5-45 kW3x200-240 VIP20
25 No No
30-90 kW3x380-480 VIP20
25 No No
0.75-18.5 kW3x380-480 VIP54
25 Yes
22-90 kW3x380-480 VIP54
25 No No
H3 RFI filter (Class A1/B)
1.5-45 kW3x200-240 VIP20
50 20 Yes No
30-90 kW3x380-480 VIP20
50 20 Yes No
0.75-18.5 kW3x380-480 VIP54
25 10 Yes
22-90 kW3x380-480 VIP54
50 10 Yes No
Table 1.36
Quick Guide VLT® HVAC Basic Drive Quick Guide
40 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
Protection and features
• Electronic thermal motor protection motor protection against overload.
• Temperature monitoring of the heatsink ensures that the frequency converter trips in case of overtemperature.
• The frequency converter is protected against short-circuits between motor terminals U, V, W.
• If a motor phase is missing, the frequency converter trips and issues an alarm.
• If a mains phase is missing, the frequency converter trips or issues a warning (depending on the load).
• Monitoring of the intermediate circuit voltage ensures that the frequency converter trips if the intermediate circuitvoltage is too low or too high.
• The frequency converter is protected against earth faults on motor terminals U, V, W.
Mains supply (L1, L2, L3)Supply voltage 200-240 V ±10%Supply voltage 380-480 V ±10%Supply voltage 525-600 V ±10%Supply frequency 50/60 HzMax. imbalance temporary between mains phases 3.0% of rated supply voltageTrue Power Factor (λ) ≥ 0.9 nominal at rated loadDisplacement Power Factor (cosφ) near unity (>0.98)Switching on the input supply L1, L2, L3 (power-ups) enclosure frame H1-H5, I2, I3, I4 Max. 2 times/min.Switching on the input supply L1, L2, L3 (power-ups) enclosure frame H6-H8, I6-I8 Max. 1 time/min.Environment according to EN 60664-1 overvoltage category III/pollution degree 2The unit is suitable for use on a circuit capable of delivering not more than 100.000 RMS symmetrical Amperes, 240/480 Vmaximum.
Motor output (U, V, W)Output voltage 0-100% of supply voltageOutput frequency 0-200 Hz (VVCplus), 0-400 Hz (u/f)Switching on output UnlimitedRamp times 0.05-3600 s
Cable lengths and cross sectionsMax. motor cable length, screened/armoured (EMC correct installation) See 1.7.5 EMC Test ResultsMax. motor cable length, unscreened/unarmoured 50 mMax. cross section to motor, mains*Cross section DC terminals for filter feedback on enclosure frame H1-H3, I2, I3, I4 4 mm2/11 AWGCross section DC terminals for filter feedback on enclosure frame H4-H5 16 mm2/6 AWGMaximum cross section to control terminals, rigid wire 2.5 mm2/14 AWG)Maximum cross section to control terminals, flexible cable 2.5 mm2/14 AWG)Minimum cross section to control terminals 0.05 mm2/30 AWG*See 1.7.2 Mains Supply 3x380-480 V AC for moreinformation
Digital inputsProgrammable digital inputs 4Terminal number 18, 19, 27, 29Logic PNP or NPNVoltage level 0-24 V DCVoltage level, logic '0' PNP <5 V DCVoltage level, logic '1' PNP >10 V DCVoltage level, logic '0' NPN >19 V DCVoltage level, logic '1' NPN <14 V DCMaximum voltage on input 28 V DCInput resistance, Ri Approx. 4 kDigital input 29 as thermistor input Fault: >2.9 kΩ and no fault: <800 Ω
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 41
1 1
Downloaded from www.Manualslib.com manuals search engine
Analog inputsNumber of analog inputs 2Terminal number 53, 54Terminal 53 mode Parameter 6-19: 1=voltage, 0=currentTerminal 54 mode Parameter 6-29: 1=voltage, 0=currentVoltage level 0-10 VInput resistance, Ri approx. 10 kΩMax. voltage 20 VCurrent level 0/4 to 20 mA (scalable)Input resistance, Ri <500 ΩMax. current 29 mA
Analog outputNumber of programmable analog outputs 2Terminal number 42, 451)
Current range at analog output 0/4-20 mAMax. load to common at analog output 500 ΩMax. voltage at analog output 17 VAccuracy on analog output Max. error: 0.4% of full scaleResolution on analog output 10 bit
1) Terminal 42 and 45 can also be programmed as digital outputs.
Digital outputNumber of digital outputs 2Terminal number 42, 451)
Voltage level at digital output 17 VMax. output current at digital output 20 mAMax. load at digital output 1 kΩ
1) Terminals 42 and 45 can also be programmed as analog output.
Control card, RS-485 serial communicationTerminal number 68 (P, TX+, RX+), 69 (N, TX-, RX-)Terminal number 61 Common for terminals 68 and 69
Control card, 24 V DC outputTerminal number 12Max. load enclosure frame H1-H8, I2-I8 80 mA
Relay outputProgrammable relay output 2Relay 01 and 02 01-03 (NC), 01-02 (NO), 04-06 (NC), 04-05 (NO)Max. terminal load (AC-1)1) on 01-02/04-05 (NO) (Resistive load) 250 V AC, 3 AMax. terminal load (AC-15)1) on 01-02/04-05 (NO) (Inductive load @ cosφ 0.4) 250 V AC, 0.2 AMax. terminal load (DC-1)1) on 01-02/04-05 (NO) (Resistive load) 30 V DC, 2 AMax. terminal load (DC-13)1) on 01-02/04-05 (NO) (Inductive load) 24 V DC, 0.1 AMax. terminal load (AC-1)1) on 01-03/04-06 (NC) (Resistive load) 250 V AC, 3 AMax. terminal load (AC-15)1) on 01-03/04-06 (NC) (Inductive load @ cosφ 0.4) 250 V AC, 0.2 AMax. terminal load (DC-1)1) on 01-03/04-06(NC) (Resistive load)
30 V DC, 2 AMin. terminal load on 01-03 (NC), 01-02 (NO) 24 V DC 10 mA, 24 V AC 20 mA
Environment according to EN 60664-1 Overvoltage category III/pollution degree 21) IEC 60947 parts 4 and 5.
Control card, 10 V DC outputTerminal number 50Output voltage 10.5 V ±0.5 VMax. load 25 mA
Quick Guide VLT® HVAC Basic Drive Quick Guide
42 MG18A402 - VLT® is a registered Danfoss trademark
11
Downloaded from www.Manualslib.com manuals search engine
All inputs, outputs, circuits, DC supplies and relay contacts are galvanically isolated from the supply voltage (PELV) andother high-voltage terminals.
SurroundingsEnclosure IP20Enclosure kit available IP21, TYPE 1Vibration test 1.0 gMax. relative humidity 5%-95% (IEC 60721-3-3; Class 3K3 (non-condensing) during operationAggressive environment (IEC 60721-3-3), coated (standard) frame H1-H5 Class 3C3Aggressive environment (IEC 60721-3-3), non-coated frame H6-H10 Class 3C2Aggressive environment (IEC 60721-3-3), coated (optional) frame H6-H10 Class 3C3Test method according to IEC 60068-2-43 H2S (10 days)Ambient temperature See max. output current at 40/50 °C in the tables mains supply
Derating for high ambient temperature, see 1.7.6 Surroundings
Minimum ambient temperature during full-scale operation 0 °CMinimum ambient temperature at reduced performance, enclosure frame H1-H5 -20 °CMinimum ambient temperature at reduced performance, enclosure frame H6-H10 -10 °CTemperature during storage/transport -30 to +65/70 °CMaximum altitude above sea level without derating 1000 mMaximum altitude above sea level with derating 3000 mDerating for high altitude, see 1.7.6 SurroundingsSafety standards EN/IEC 61800-5-1, UL 508CEMC standards, Emission EN 61800-3, EN 61000-6-3/4, EN 55011, IEC 61800-3
EMC standards, ImmunityEN 61800-3, EN 61000-3-12, EN 61000-6-1/2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN
61000-4-5, EN 61000-4-6
1.8 Special Conditions
1.8.1 Derating for Ambient Temperatureand Switching Frequency
The ambient temperature measured over 24 hours shouldbe at least 5°C lower than the max. ambient temperature.If the frequency converter is operated at high ambienttemperature, the continuous output current should bedecreased. For derating curve, see VLT® HVAC Basic DesignGuide MG18C.
1.8.2 Derating for Low Air Pressure
The cooling capability of air is decreased at low airpressure. For altitudes above 2000 m, contact Danfossregarding PELV. Below 1000 m altitude no de-rating isnecessary, but above 1000 m the ambient temperature orthe maximum output current should be decreased.Decrease the output by 1% per 100 m altitude above 1000m or reduce the max. ambient temperature by 1° per 200m.
1.9 Options for VLT® HVAC Basic Drive FC101
For options, see the VLT® HVAC Basic Design Guide MG18C.
1.10 MCT 10 Support
MCT 10 information is available at: www.danfoss.com/BusinessAreas/DrivesSolutions/fc101driveupdates
Quick Guide VLT® HVAC Basic Drive Quick Guide
MG18A402 - VLT® is a registered Danfoss trademark 43
1 1
Downloaded from www.Manualslib.com manuals search engine
MAKING MODERN LIVING POSSIBLE
QQuick GuideVLT® HVAC Basic Drive FC 101
www.danfoss.com/drives
*MG18A402*132R0078 MG18A402 Rev. 2012-03-23
Downloaded from www.Manualslib.com manuals search engine