TOS VARNSDORF WHN 13.8 CNC Bj 1995 - maschinen-kistner.de
Transcript of TOS VARNSDORF WHN 13.8 CNC Bj 1995 - maschinen-kistner.de
TOS VARNSDORF WHN 13.8 CNC
KISTNER GmbH & Co. KG
Industriestraße 7-9 D-95349 Thurnau
Tel. (+49) 9228 987-0 [email protected] www.maschinen-kistner.de
KISTNER USED MACHINES We are your specialist
LIST OF CONTENTS
Machine info ………………………………………….………..………………………..…………………………. Equipment …………………………………………………………….………………………..…………………..…. Installation data ……………………………………………………..………………………………………..
Drawings of the machine ………………………………..…………………………….………
Machine pictures ……………………………….…………………………………………………....………
Foundation plan ………………………………………………………………………………………………..
3 4 5 9 12 14
TOS VARNSDORF WHN 13.8 CNC | | 2
2
MACHINE INFO
Manufacturer
Type
Year of manufacture
Control
Machine number Travels
| 3 TOS VARNSDORF WHN 13.8 CNC |
| 4 TOS VARNSDORF WHN 13.8 CNC |
EQUIPMENT
Increased working table Table load
Electronic hand wheel Strengthened and additional
coolant device Universal-milling attachment
Electronic probe User guide / Documentation Machine parameters on CD
| 5 TOS VARNSDORF WHN 13.8 CNC |
INSTALLATION DATA
Max. lenght and width of the machine (including electric cabinets) with the
adjustment in the X – axis = 3.500 mm Built ground-plan area of the machine
with X = 3.500 mm Max. height of the machine with
adjustment in the Y- axis = 2.000 mm Total machine power input
Table Max. workpiece weight
Mechanical part
| 6 TOS VARNSDORF WHN 13.8 CNC |
Diameter of the working spindle Taper sleeve of the work spindle
Flange diameter of the hollow spindle Max. diameter of the centering of
the hollow spindle (7 : 24) Minimum distance from the front face of
the spindle from the front face of the hollow spindle
Diameter of the centering flange of the cutting device
Clamping force of the tool Conversion of the end face of the work
spindle in the spindle stroke Change of the face in the post feed
Axis conversion of the work spindle in the Y axis with the parameters start in the plane of the clamping table according
to the stand height
Headstock
Work spindle speed
Mechanical stages with outcome 355 and 1.500 rpm The possibility of percentage change during the machine operation in the range of 50 - 120 %, however at most at the low rows 400 rpm
and at the higher rows 1.600 rpm Max. torque at the spindle speed range of 10-105 is 3379 Nm
| 7 TOS VARNSDORF WHN 13.8 CNC |
Table clamping area (large table) Maximum load
Diameter of the center hole for the clamping surfaces
Depth of the centering of the clamping area
Clamping slots T CSN 02 1030 Division of the T-slots
Minimum spacing of table rotation from the end face of the working spindle Cross adjustment of the table with
a long cross bed
Worktable
Operating platform
Vertical change of operating platform Sustainability of operation stage
Adjustment speed
Feeds
A programmable feed is valid in the axes X, Y, Z and W in the range of up to 8.000 mm/min. Possibility of
percentage change during the operation in the range of 0-150% of the programmable value,
at most 8.000 mm/min The minimum working feed in X, Y, Z and W
Table turning - axis B Axis B (table turning) is intended for positioning
| 8 TOS VARNSDORF WHN 13.8 CNC |
Motor regulator for speeds of the work spindle Servomotors for coordinate drive
Coordinates for: -Cross adjustment of table slide
-Vertical travel of headstock -Longitudinal adjustment of the stand
-Table turning Coordinate for the spindle stroke
Motor of the hydraulic unit Engine of the lubrication unit, depending on the
machine configuration with the aggregate either 7AZ (ZTS Brno)
or MFE 5/B (W) 7 (Company Vogel)
- Motor of the unit for lubrication and cooling of the headstock and speed circuit
- Motor of the operation stage
Main electric motors
Screw thread
With the help of the electronic coupling between the spindle speed and the feed screw
speeds for the spindle stroke Slope area Increment
| 9 TOS VARNSDORF WHN 13.8 CNC |
DRAWINGS OF THE MACHINE
| 10 TOS VARNSDORF WHN 13.8 CNC |
| 11 TOS VARNSDORF WHN 13.8 CNC |
MACHINE PICTURES
| 12 TOS VARNSDORF WHN 13.8 CNC |
2 | 13 TOS VARNSDORF WHN 13.8 CNC |
2 | 14 TOS VARNSDORF WHN 13.8 CNC |