Thomas Riegler Système d'altération et ... - Tableau de bord
Transcript of Thomas Riegler Système d'altération et ... - Tableau de bord
THÈSE
Pour l'obtention du grade deDOCTEUR DE L'UNIVERSITÉ DE POITIERS
UFR des sciences fondamentales et appliquéesInstitut de chimie des milieux et matériaux de Poitiers - IC2MP
(Diplôme National - Arrêté du 7 août 2006)
École doctorale : Sciences pour l'environnement - Gay Lussac (La Rochelle)Secteur de recherche : Terre solide et enveloppes superficielles
Présentée par :Thomas Riegler
Système d'altération et minéralisation en uranium le long dufaisceau structural Kiggavik-Andrew Lake (Nunavut, Canada) :
modèle génétique et guides d'exploration
Directeur(s) de Thèse :Daniel Beaufort
Soutenue le 10 décembre 2013 devant le jury
Jury :
Président Alain Meunier Professeur des Universités, Université de Poitiers
Rapporteur Michel Cuney Directeur de recherche CNRS, Université de Nancy 1
Rapporteur Michel Jébrak Professeur, Université du Québec à Montréal
Membre Daniel Beaufort Professeur des Universités, Université de Poitiers
Membre Maurice Pagel Professeur des Universités, Université Paris Sud 11, Orsay
Membre David Quirt Senior Geoscientist, AREVA Resources Canada
Membre Thierry Allard Directeur de recherche CNRS, Université Paris 6, Jussieu
Membre Charlie Jefferson GEM uranium Project leader, Geological Survey of Canada
Pour citer cette thèse :Thomas Riegler. Système d'altération et minéralisation en uranium le long du faisceau structural Kiggavik-AndrewLake (Nunavut, Canada) : modèle génétique et guides d'exploration [En ligne]. Thèse Terre solide et enveloppessuperficielles. Poitiers : Université de Poitiers, 2013. Disponible sur Internet <http://theses.univ-poitiers.fr>
THESE
Pour l’obtention du Grade de
DOCTEUR DE L’UNIVERSITE DE POITIERS
(Diplôme National - Arrêté du 7 août 2006) UFR Sciences Fondamentales et Appliquées
Ecole Doctorale : Gay-Lussac
Secteur de Recherche : Terre solide et enveloppes superficielles.
Présentée par :
Thomas Riegler
************************
Système d’altération et minéralisation en uranium le long du faisceau structural Kiggavik - Andrew Lake (Nunavut, Canada) : modèle
génétique et guides d’exploration
************************ Directeur de Thèse : M. Daniel Beaufort
************************
Soutenue le 10 décembre 2013
devant la Commission d’Examen
************************
JURY
Rapporteurs: MM. M. Cuney Directeur de recherche CNRS, Nancy I M. Jébrak Professeur, Université du Québec à Montréal
Examinateurs: MM. M. Pagel Professeur, Université Paris Sud XI Orsay D. Quirt Senior Geoscientist, AREVA Resources Canada
C. Jefferson GEM uranium Project Leader, Geological Survey of Canada T. Allard Directeur de recherche CNRS, Paris VI Jussieu A. Meunier Professeur, Université de Poitiers D. Beaufort Professeur, Université de Poitiers
2
Remerciements
Ce travail est le fruit d’une longue aventure commencée dans les prairies de la Saskatchewan,
il y a de cela trois années. Je remercie donc les initiateurs de se projet : Joseph Roux, Dave
Quirt, Jean-Pierre Milesi et Jean-Luc Lescuyer de m’avoir fait confiance pour mener à bien
cette étude. Merci à AREVA Resources Canada, AREVA NC et ERM pour le support financier
et admnistratif de cette thèse, enfin bien sur au laboratoire HydrASA pour son acceuil.
Je tiens également remercier Daniel Beaufort, pour sa patience, ses conseils, et le partage de
ses connaissances. Ce fût un plaisir depuis notre première rencontre à Shea Creek, et j’espère
que cette relation scientifique et amicale durera après le strict cadre de cette thèse.
Bien évidement je suis reconnaissant à Michel Cuney et Michel Jébrak de bien vouloir être les
rapporteurs de ce travail. A Maurice Pagel, Dave Quirt, Charlie Jefferson, Thierry Allard et
Alain Meunier de me faire eux aussi l’honneur de faire partie de mon jury.
De manière plus particulière je voudrais remercier Thierry Allard, Mostafa Fayek et Maurice
Pagel pour leur accueil dans leurs laboratoires respectifs et de leur aide au cours de ce
travail.
Une pensée chaleureuse pour Peter Wollenberg donc la contribution a été essentielle de par
son experience et sa connaissance de la zone de Kiggavik. J’attends avec impatience le livre
du récit de tes aventures arctiques !
J’aurai aussi une pensée pour mes collègues et amis, présents ou passés. De l’Université de
Poitiers ou d’HydrASA ; merci Alain pour tes conseils toujours judicieux, ta disponibilité et
ton humour, à mes voisins de palier Paul et Laurent, Thierry toujours là quand il faut, Abder
bien sûr, et pardon pour tous les autres. Je garderai un excellent souvenir de mon passage ici.
Merci également à Marion, Freddy, Mélissa, Emilie, Antoine et Jo pour votre accueil lors de
mon arrivé à Poitiers. Plus récement à Fabien, Jean-Christophe, Sophie et Valentin pour leur
amitié, avec une mention spéciale pour les pros de la belote et de l’ultracentrifugeuse. Un
pensée aussi pour les amis de l’ESIP, Anne-Laure et Benoit ; du 504 à Orsay, Tony et
Morgane ; ou ceux Dysart Road à U of M, thanks Ryan. Enfin, de Saskatoon, Dwayne, Mario,
et tout particulièrement Nancy, Drew, et Rebecca.
3
Ces trois années à Poitiers ont été riches de nouvelles rencontres. La liste est trop longue,
mais je ne peux pas oublier Lindsay, Mariana, Juan-Pablo, Jamal, Solweig, Camila, Chi-Wei,
Blandine, Emilie, et Gabriel.
Une pensée aux Gaúchos : Amanda, et sa famille ; Edson, Victória.
À Christophe mon camarade depuis maintenant 10 ans. Pour le soutien dans les moments
difficiles et les discussions sur la métallogénie toujours passionnante.
Enfin merci à ma famille ; à Mathias, Maud, et Mathieu pour leur générosité lors de mes
nombreux passages à Paris ; à ma sœur Chloé bien sûr, et tout particulièrement à mes
parents pour leur soutien indéfectible depuis toujours.
4
Aussi audacieux soit-il d’explorer
l’inconnu, il l’est plus encore de remettre
le connu en question.
Kaspar
C’était un ancien basset qui, à force de
travail, d’énergie, d’ambition, de
volonté, de sens civique, avait réussi à
devenir un saint-bernard fort correct.
Pierre Dac
5
Table des matières
1. INTRODUCTION ............................................................................................................................................. 9
1.1. Introduction générale ...................................................................................................................... 9
1.2. Enjeux ............................................................................................................................................ 10
2. PRÉSENTATION DU MÉMOIRE DE THÈSE ............................................................................................................ 11
3. RAPPELS BIBLIOGRAPHIQUES .......................................................................................................................... 14
3.1. Le ou lie Ca adie et les assi s d’âge Pal op ot ozoi ue ..................................................... 14
3.2. Les minéralisations de type discordance ....................................................................................... 19
3.3. Gitologie des i alisatio s u a if es asso i es au dis o da es d’âge pal op ot ozoï ue 21
3.4. Contrôle structural régional et local des minéralisations .............................................................. 25
3.5. Typologie des altérations .............................................................................................................. 26
3.6. Quelques repères chronologiques : âges des minéralisations, événements thermiques (diagenèse
& intrusions) et o te te g od a i ue e lie ave les i alisatio s d’u a iu de l’Atha as a et du
Thelon 30
3.7. G ologie des gise e ts d’u a iu du dist i t de Kiggavik ........................................................... 32
4. RÉFÉRENCES ............................................................................................................................................... 41
5. ECHANTILLONNAGE ...................................................................................................................................... 47
A. LE SYSTEME D’ALTERATION DU FAISCEAU DE KIGGAVIK-ANDREW LAKE ET SES RELATIONS AVEC LES
MINERALISATIONS EN URANIUM ................................................................................................................... 48
1. ALTERATION RELATED TO URANIUM DEPOSITS IN THE KIGGAVIK-ANDREW LAKE STRUCTURAL TREND, NUNAVUT, CANADA;
NEW INSIGHTS FROM PETROGRAPHY AND CLAY MINERALOGY .......................................................................................... 49
1.1. Abstract ......................................................................................................................................... 49
1.2. Introduction ................................................................................................................................... 50
1.3. Geological setting .......................................................................................................................... 53
1.4. Sampling and analytical procedure ............................................................................................... 54
1.5. Petrography and mineralogy......................................................................................................... 57
1.6. Textural properties and crystal structure of phyllosilicates ........................................................... 63
6
1.7. Phyllosilicate crystal chemistry ...................................................................................................... 66
1.8. Discussion ...................................................................................................................................... 69
1.9. Concluding remarks ....................................................................................................................... 77
1.10. References ..................................................................................................................................... 79
2. ETUDE MICROTHERMOMETRIQUE DES INCLUSIONS FLUIDES DANS LES QUARTZ ET DOLOMITE ASSOCIEES AUX
MINERALISATIONS URANIFERES DU FAISCEAU STRUCTURAL KIGGAVIK-ANDREW LAKE .......................................................... 83
2.1. Introduction ................................................................................................................................... 83
2.2. Bong .............................................................................................................................................. 83
2.3. End Grid ......................................................................................................................................... 85
2.4. Interprétations et perspectives...................................................................................................... 91
3. ILLITE & URANINITE GEOCHRONOLOGY ............................................................................................................ 96
3.1. Introduction ................................................................................................................................... 96
3.2. Ar/Ar principle and method ........................................................................................................... 96
3.3. Samples ......................................................................................................................................... 98
3.4. Results ........................................................................................................................................... 99
3.5. Discussion .................................................................................................................................... 103
3.6. References ................................................................................................................................... 107
4. THE BASAL THELON FORMATION AT KIGGAVIK ................................................................................................. 108
4.1. Methods ...................................................................................................................................... 108
4.2. Sandstones regional setting ........................................................................................................ 109
4.3. Bulk-rock chemistry of the Basal Thelon sandstones .................................................................. 112
4.4. Petrography and mineralogy....................................................................................................... 114
4.5. Crystallochemical properties of kaolin minerals.......................................................................... 120
4.6. Microcrystalline quartz cement chemistry and in situ composition of oxygen isotopes ............ 126
4.7. Discussion .................................................................................................................................... 128
4.8. Conclusion ................................................................................................................................... 133
4.9. References ................................................................................................................................... 135
5. CARBONACEOUS MATERIAL OCCURRENCE IN THE KIGGAVIK URANIUM DEPOSITS (THELON, NUNAVUT, CANADA). ......... 139
5.1. Introduction ................................................................................................................................. 139
7
5.2. Geological setting and petrography ............................................................................................ 141
5.3. Samples & Methods .................................................................................................................... 144
5.4. Results ......................................................................................................................................... 144
5.5. Discussion .................................................................................................................................... 151
5.6. Conclusion ................................................................................................................................... 157
5.7. References ................................................................................................................................... 157
B. LES MARQUEURS MINÉRALOGIQUES .................................................................................................. 163
1. SPATIAL DISTRIBUTION AND COMPOSITIONAL VARIATION OF APS MINERALS RELATED TO URANIUM DEPOSITS IN THE
KIGGAVIK ANDREW LAKE STRUCTURAL TREND, NUNAVUT, CANADA. ............................................................................. 164
1.1. Abstract ....................................................................................................................................... 164
1.2. Introduction ................................................................................................................................. 165
1.3. Regional geological setting ......................................................................................................... 166
1.4. Sampling and methods ................................................................................................................ 169
1.5. APS minerals and alteration petrography ................................................................................... 172
1.6. Electron microprobe data ............................................................................................................ 179
1.7. Whole rock chemistry and REE distribution................................................................................. 188
1.8. Discussion .................................................................................................................................... 193
1.9. Conclusion ................................................................................................................................... 200
1.10. References ................................................................................................................................... 202
2. NATURE AND STABILITY OF RADIATION INDUCED DEFECTS IN NATURAL ILLITE NEW RESULTS AND IMPLICATIONS FOR ANCIENT
RADIOELEMENT MOBILITY ...................................................................................................................................... 205
2.1. Introduction ................................................................................................................................. 205
2.2. Sampling ...................................................................................................................................... 206
2.3. Methods ...................................................................................................................................... 207
2.4. Annealing Experiments protocol ................................................................................................. 208
2.5. Results ......................................................................................................................................... 209
2.6. Preliminary discussion and concluding remarks .......................................................................... 214
2.7. References ................................................................................................................................... 216
8
C. DISCUSSION GÉNÉRALE, CONCLUSIONS ET PERSPECTIVES .................................................................. 217
1. DISCUSSION GENERALE ............................................................................................................................... 218
1.1. Histoi e des v e e ts d’alt atio .......................................................................................... 219
1.2. Evénements précoces Hudsoniens ............................................................................................... 219
1.3. Mise e pla e du p ofil d’alt atio P -Thélon .......................................................................... 223
1.4. Diagenèse et évolution du bassin du Thelon ............................................................................... 224
1.5. Altération hydrothermale et mise en place de la minéralisation ................................................ 225
2. CONCLUSION GENERALES ET PERSPECTIVES ...................................................................................................... 228
3. RÉFÉRENCES ............................................................................................................................................. 229
Introduction
9
1. Introduction
1.1. Introduction générale
La région de Kiggavik dans le Territoire du Nunavut est un district majeur pour l’exploration
de l’uranium dans le bouclier Canadien, et l’un des plus actifs au Canada en dehors de
l’Athabasca dans la province de la Saskatchewan. Les premiers travaux d’exploration menés
dans la zone du bassin du Thelon, il y a une trentaine d’années ont fait suite aux découvertes
de minéralisations uranifères à hautes teneurs dans le bassin Paléoprotérozoïque de
l’Athabasca. Dans les deux cas, les reconnaissances radiométriques au sol et aéroportées ont
permis la découverte des minéralisations encaissées dans le socle et dans les formations
gréseuses sus-jacentes. Par la suite, lorsque le modèle de minéralisation de type discordance a
été établi, l’exploration s’est poursuivie plus en profondeur, sur des cibles cachées sous la
couverture sédimentaire et parfois même sous des épaisseurs conséquentes de roches de socle.
Ainsi la géophysique a permis d’identifier les grandes structures régionales tandis que la
pétrographie, la minéralogie, et la géochimie ont fourni les outils pour tracer les systèmes
hydrothermaux potentiellement favorables à la formation de gites uranifères. A Kiggavik les
minéralisations ne sont pour le moment que rattachées par extrapolation à un modèle de type
discordance, de par leur localisation à deux kilomètres des grès de la Formation du Thelon. Il
est alors fondamental de le confirmer par une approche gîtologique, et pétrographique
géochimique, minéralogique afin de mieux cerner le fonctionnement du système d’altération
et de minéralisation et si possible de définir des métallotectes pertinents. Enfin la position des
minéralisations reconnues à plusieurs centaines de mètres sous la surface d’érosion actuelle à
Kiggavik, pose la question de l’extension potentielle en profondeur des minéralisations
encaissées dans le socle dans l’Athabasca. Il y a alors une problématique aux multiples
implications ne se limitant pas aux seules minéralisations du Thelon et qui peuvent s’étendre à
Introduction
10
d’autre district uranifère associées aux discordances, dans le bouclier Canadien ou en
Australie.
1.2. Enjeux
Les enjeux de ce travail sont multiples et recouvrent à la fois la minéralogie, pétrologie, la
géochimie et la gîtologie des minéralisations uranifère de Kiggavik pour tenter de comprendre
les relations entre l’altération et les concentrations en uranium dans une vue prospective. Pour
cela une approche globale, de l’échelle du district à celle du minéral, a été nécessaire afin de
cerner les objets minéralisés dans leur contexte. Il s’est agi de prendre en compte l’ensemble
des éléments favorables à la formation des concentrations en uranium tels que les
discontinuités, les lithologies, les minéraux ou bien encore les paramètres contrôlant l’oxydo-
réduction pour n’en citer que quelques uns. C’est donc par une approche multidisciplinaire,
intégrée, et en ayant recourt à un grand nombre de méthodes chacune pertinente pour la
compréhension d’un élément clef du système géologique si particulier qu’est un gîte
métallique que nous tenterons de répondre aux thématiques ou questions suivantes :
- Quelles sont les paragenèses d’altération associées aux minéralisations uranifère de
Kiggavik ?
- Quelles sont leurs implications pour l’interprétation géologique et quel potentiel
représentent les minéraux argileux produits par ces altérations pour l’exploration.
- Comment s’organisent ces altérations à l’échelle régionale ?
- Quelle est leur contribution au modèle génétique de la minéralisation ?
Présentation du mémoire de thèse
11
2. Présentation du mémoire de thèse
Les résultats présentés dans ce mémoire s’organisent autour de β grandes parties, elles-mêmes
subdivisées en chapitres, principalement sous forme d’articles. De manière préliminaire le
cadre géologique régional, local concernant les minéralisations en uranium, sera présenté de
même que l’échantillonnage de la zone d’étude.
Le premier volet de ce travail (partie A) s’attardera sur la caractérisation du système
d’altération et ses relations avec les minéralisations en uranium, tandis que le second (partie
B) sera axé sur les marqueurs minéralogiques s.l. de ce système. Enfin les éléments présentés
dans ces deux grands axes feront l’objet d’une synthèse et seront discutés dans la partie C.
Dans le premier chapitre (article 1), il s’agit de caractériser l’altération en relation avec les
minéralisations uranifère de Kiggavik et pour cela d’identifier la minéralogie et les
paragenèses minérales résultant des différents épisodes d’interactions fluide roches qui se sont
succédés au cours du temps. La minéralogie permet alors de proposer des clefs
d’interprétation des systèmes hydrothermaux de Kiggavik par comparaison avec les
signatures d’altération déjà identifiées autour des gisements de type associés aux discordances
au Canada et en Australie et de proposer des pistes pour les transferts élémentaires lors de
l’altération. Enfin la cristallographie détaillée des minéraux argileux, permet, en plus des
aspects comparatifs, de proposer un nouvel outil cartographique de l’altération. De plus cet
article sera complété d'un deuxième chapitre traitant des aspects paléofluides afin de mieux
cerner les fluides en relations avec les phénomènes d’altération et de minéralisation. Enfin, un
troisième chapitre présentera des éléments de géochronologie, à la fois sur les minéraux
argileux et sur la minéralisation.
Dans un quatrième chapitre (article 2), on s’interessera aux relations entre le socle et la
couverture gréseuse, principalement par l’étude des formations basales du bassin du Thelon. Il
Présentation du mémoire de thèse
12
s’agira alors de retracer la nature et l’origine des apports sédimentaires puis de suivre
l’évolution diagénétique du bassin grâce entre autres aux minéraux du groupe kaolin.
Enfin en prélude à la conclusion de cette première partie, le cinquième chapitre (article 3)
concernera les matières carbonées, autre composante fréquemment associée aux gîtes de type
discordance. Elles feront l’objet d’une caractérisation poussée afin de proposer leur
intégration comme une composante de la paragenèse d’altération.
La deuxième partie (B) du manuscrit sera consacrée à l’identification de marqueurs
minéralogiques connus pour leur réponse cristallochimique aux variations du pH et des
conditions d’oxydoréduction du milieu ou leur potentiel pour la dosimétrie de la radioactivité
naturelle. Le premier chapitre (article 4), consiste en la compréhension spatiale et temporelle
des phosphates et sulfates d’aluminium formés lors des événements diagénétiques et
hydrothermaux. Il s’agit également de comprendre, à travers le prisme des terres rares, les
transferts et la mobilité des éléments, dont l’uranium, au cours de l’histoire géologique ayant
conduit à la formation des zones minéralisées à Kiggavik. Une approche « bilan de masse »
sera mise en œuvre pour compléter la pétrographie et la cristallochimie. Le deuxième chapitre
aura pour objet la compréhension de l’expression des défauts d’irradiation dans l’illite. Il
s’agit de raffiner la compréhension de la manifestation des différentes composantes
constitutives du signal RPE dans l’illite pour dégager ses caractéristiques fondamentales et
ainsi contribuer à une meilleure interprétation des circulations des radioéléments (pre, syn ou
post minéralisation) dans un système géologique ou les remobilisations de l’uranium sont un
phénomène fréquent (article 5).
Enfin, la troisième dernière partie (C) sera consacrée à une discussion globale de l’ensemble
des résultats des travaux de la thèse dans laquelle l‘accent sera mis sur la proposition d’un
Présentation du mémoire de thèse
13
modèle métallogénique pour les minéralisations uranifère du faisceau structural de Kiggavik –
Andrew Lake et sur les perspectives scientifiques.
Rappels bibliographiques
14
3. Rappels bibliographiques
La présentation du contexte géologique multi-échelle qui suit a pour objectif de replacer la
zone de Kiggavik dans un cadre lithologique et structural en accordant une attention
particulière à la métallogénie de l’uranium et aux processus d’altération associés. Bien
évidemment compte tenu de la proximité des contextes géologiques, de nombreux éléments
de la littérature qui font référence aux bassins d’âge Méso-Paléoproterozoique de l’Athabasca
(Canada) et de Kombolgie (Australie) seront également mentionnés.
3.1. Le bouclier Canadien et les bassins d’âge Paléoprotérozoique
Figure 3-1 : Carte géologique simplifiée du bouclier canadien, (Corrigan et al. 2007)
Le bouclier canadien, figure 3-1, est un ensemble géologique complexe dont l’organisation
actuelle est liée à l’accrétion de cratons archéens soudés par des ceintures orogéniques lors
des phases Talson - Thelon (2.0 -1.9 Ga) et Trans-Hudsonienne (1.9 - 1.8 Ga) (Hoffman
Rappels bibliographiques
15
1988; Hoffman 1990). Le supercontinent de la Laurentia était alors composé de blocs
constitués des provinces du Supérieur-Nain, de Churchill-Wyoming et de l’Esclave
respectivement à l’est et l’ouest de la baie d’Hudson. De grandes zone mylonitiques à
l’échelle lithosphérique telle que la Snowbird Tectonic Zone (STZ) séparant les sous
provinces de Rae et de Hearne constituent l’une des discontinuités majeures de la partie ouest
de la province de Chuchill. Elles marquent un événement majeur de dislocation puis de suture
du bloc Churchill-Wyoming avec le bloc de Queen Maude (Hanmer et al. 1995; Hoffman
1988). Au final, la configuration du bouclier résulte à la fois des phases multiples de
structuration des cratons à l’Archéen, et des phases d’extension (rifting) avec mise en place de
séries volcano-sédimentaires archéennes au niveau des marges passives de ces cratons qui
sont à l’origine des ceintures de roches vertes avec les groupes de Murmac Bay, Woodburn,
Prince Albert et Mary River pour la province de Churchill (Hartlaub et al. 2004; Ashton
1988).
L’orogène Trans- Hudsonien est d’une importance majeure du point de vue métallogénique.
On retrouve toutes les étapes de son évolution sur une période allant de 2.45 à 1.95 Ga,
incluant la phase de rifting lors de l’ouverture de l’océan Manikewan (Stauffer 1984) suivie
du dépôt de sédiments sur les marges des cratons archéens ou des bassins intra-cratoniques
(e.g Groupe de Wollaston, Hurwitz, Amer) (Aspler et al. 2001), puis la formation de croûte
océanique, d’arc volcaniques océaniques et continentaux et de bassins d’arrière arc. Cet
enregistrement complet de l’orogène et la variété des environnements géologiques qui le
composent expliquent sa renommée mondiale pour les amas sulfurés volcanogéniques (e.g
Flin-Flon), magmatiques à Ni-Cu-EGP (e.g Thompson, Raglan) et dans une moindre mesure
pour l’or orogénique (e.g Seabee), ainsi que pour les formations de fer rubanées (Corrigan et
al. 2007; Kerrich et al. 2005). A cela s’ajoute des événements tectono-metamorphiques
exprimés dans une tectonique ductile le long de zones de cisaillement, d’écaillage et de
Rappels bibliographiques
16
plissement ainsi que la recristallisation des roches dans les conditions des faciès schiste vert à
amphibolite supérieur du métamorphisme régional (Aspler et al. 2002).
Vers la transition Paléo -Méso-protérozoique, de grands bassins intra-continentaux de
composition silicoclastique se sont mis en place lors des phases de démantèlement des grands
orogènes Paléoproterozoiques. On en identifie plusieurs au Canada: Il s’agit des bassins
d’Athabasca, du Thelon, d’Hurwitz, ou d’Hornby Bay (Figures 3-1 et 3-3). Parmi ces
bassins, certains possèdent des gisements d’uranium associés à des discordances en cours
d’exploitation et/ou de prospection (Athabasca, Thelon) et les autres présentent de forte
potentialité pour l’exploration (Jefferson et al. 2007a). Enfin les études géodynamiques et les
reconstructions paléogéographiques suggèrent un lien génétique entre le fonctionnement des
grandes orogénèses du Protérozoïque et la formation de grands bassins intra-continentaux via
des phénomènes de tectonique d’échappement et de contraintes à distance, ou de flexuration
thermique d’une croûte épaissie et structurée (Karlstrom et al. 2001; Molnar et al. 1998;
Eriksson et al. 2001; Ramaekers and Catuneanu 2004). Il existe des similitudes entre les
caractéristiques des bassins silicoclasitiques du bouclier Canadien et celles du bouclier nord-
australien, en terme de facies sédimentaires, d’âge, de position paléogéographique et de
métallogénie de l’uranium. Ceci est à rapprocher des reconstitutions paléogéographiques
(Figure 3-2) qui indiquent la proximité des bassins de la Laurentia avec ceux du craton nord
australien vers la fin du Paléoprotérozoique (Betts et al. 2008; Kerrich et al. 2005; Zhao et al.
2004).
Rappels bibliographiques
17
Figure 3-2 : Reconstitution de l’évolution de l’ensemble Australia-East Antartica et Laurentia entre 1780-1650
Ma. In (Betts et al. 2008) d’après (Bagas 2004; Duebendorfer and Houston 1987; Duebendorfer et al. 2001;
Karlstrom and Bowring 1988)
Les minéralisations d’uranium sont associées à ces bassins intracontinetaux formés d’une
séquence sédimentaire quasi horizontale, dominée par des environnements fluviatiles,
continentaux dans lesquelles des grés très riches en quartz constituent la lithologie dominante.
On retrouve néanmoins des red beds et des siltites que l’on peut rapprocher de facies de plaine
d’inondation ainsi que des facies conglomératiques fluviatiles, comme par exemple ceux qui
Rappels bibliographiques
18
sont mentionnés à la base de la formation du Thelon (Rainbird et al. 2003; Rainbird and Davis
2007). Ces bassins sont décrits comme de grands lacs intracontinentaux remplis de sables et
de graviers avec un début de sédimentation estimé entre 1730-1740 Ma pour le bassin
d’Athabasca et 17β0-1750 Ma pour le Thelon, soit quelques dizaines de millions d’années
après les derniers événements du métamorphisme enregistrées dans les sphènes des roches de
la ceinture de plis de Wollaston et daté à 1750Ma (Rainbird et al. 2006; Miller et al. 1989;
Orrell et al. 1999).
Les roches du socle situées au niveau de la discordance sont affectées par une intense
hématitisation dont l’épaisseur varie de quelques centimètres à plusieurs centaines de mètres.
L’hématitisation est particulièrement développée à l’aplomb de grandes structures. Elle est
généralement interprétée comme un paléo-profil d’altération liée à la mise en place d’un
régolithe antérieurement à la formation du bassin sur la base d’arguments texturaux ou
minéralogiques (présence de diaspore) ou bien encore de par la nature graduelle du contact
entre les zones à hématite et à chlorite, ou bien par un comportement géochimique des
éléments traces analogue à celui décrit dans d’autres profils d’altération continentale d’âge
précambrien (Macdonald 1980; Hoeve and Quirt 1984). Toutefois des éléments probants de
paléosol (tel que des pisolithes par exemple) reste encore à trouver (Hoeve and Quirt 1984).
Selon une autre hypothèse, l’hématitisation pourrait être la conséquence de l’interaction des
saumures oxydantes issues du bassin avec la partie superficielle des roches réduites du socle
au cours de la diagenèse (Cuney et al. 2003).
Rappels bibliographiques
19
Figure 3-3 : Localisation actuelle des bassins intracontinentaux MesoProterozoic de la partie West du bouclier
Canadien, d’après Jefferson et al, 2007 et Thomas, 2000.
3.2. Les minéralisations de type discordance
Les gîtes et gisements d’uranium associés aux discordances sont des objets géologiques
uniques formant une classe à part parmi les autres types de minéralisation uranifère de part les
teneurs (avec en moyenne ≈ β % U pour l’Athabasca, et ≈ 0.4 % pour le Thelon et la
Kombolgie) et les tonnages exceptionnels (Gandhi 1995; Ruzicka 1996; Jefferson et al.
2007a). La production issue des mines canadiennes représentait 17 % de l’uranium produit
dans le monde en 2011.
Rappels bibliographiques
20
La découverte et l‘interprétation des gisements uranifères canadiens est une longue et riche
histoire qui commence par les découvertes de minéralisation de type filoniennes à proximité
du Grand lac de l'Ours (Port Radium) aux alentours de 1930, puis en 1952 avec la mine
Gunnar à Uranium City, exploitée par Eldorado, une compagnie minière qui deviendra
Cameco Corporation dans les années 80. Elle s’est poursuivie par la découverte d’Elliot Lake,
un modèle de minéralisation que l’on pourrait rapprocher de ce qui est connu dans le
Witwatersrand en Afrique du Sud (Hills 1987).
Par la suite, le tournant majeur pour l’exploration de l’uranium au Canada s’est produit à la
fin des années 60, avec la découverte de minéralisations à l’affleurement dans le bassin de
l’Athabasca. Le gisement de Rabbit Lake a été découvert conjointement par Gulf Minerals
Ltd & Uranerz Exploration and Mining limited dans l’Est du bassin d’Athabasca en 1968.
Celui de Cluff Lake a été découvert dans l’ouest du bassin en 1969 par Amok Limited
(Gandhi 2006), Figure 3-4. On peut d’ailleurs noter que les découvertes de Nabarlek et
Ranger en (Territoire du Nord, Australie) ont été faites à la même époque.
Rappels bibliographiques
21
Figure 3-4 : Panneau d’indication de l’ancien camp d’Amok limited (prédécesseur de COGEMA devenu
AREVA Resources Canada) situé entre rive Sud du lac de Carswell et le site minier de Cluff Lake
(Saskatchewan, Canada).
3.3. Gitologie des minéralisations uranifères associées aux discordances d’âge
paléoprotérozoïque
Les minéralisations sont formées de lentilles massives à semi massives mais aussi de veines à
remplissage quasi exclusif d’uraninite (UO2) et situées au voisinage de la discordance basale
des bassins, entre les grès conglomératiques d’âge Paléo à Mésoproterozoiques et leur socle
métamorphique d’âge Archéen à Paléoproterozoique.Les minéralisations forment des objets
de dimensions relativement limitées mais pour lesquelles les teneurs peuvent atteindre 15 à 20
% U comme dans les mines de Cigar Lake ou de McArthur River Figure 3-5. On peut
également noter que les volumes de minéralisation reconnus pour le bassin du Thelon
représentent le dixième de celle de l’Athabasca et que les teneurs moyennes enregistrées
(environ 0.5 %) sont beaucoup plus faibles que celles mesurées dans l’Athabasca et proches
de celles rencontrées dans les gisements Australiens de l’Alligator River (Battey et al. 1987;
Ruzicka 1993). Ainsi on peut légitiment questionner le potentiel de découverte pour cette
zone encore sous explorée que constitue le Thelon et dans lequel s’inscrit la présente étude.
Rappels bibliographiques
22
Figure 3-5 : Relation entre teneur et tonnage des différents gisements d'uranium associés à des discordances en
Australie et au Canada (d'après Gandhi 1995; Ruzicka 1996; Jefferson et al. 2007a; Gandhi 2006). Les différents
gisements et prospects de Kiggavik sont représentés en bleu alors que les deux gisements géants de l’Athabasca
que sont McArthur et Cigar sont en rouge. L’encadré donne les teneurs moyennes les ressources et les réserves
ainsi que la production passée pour chacun des bassins Paléoprotérozoiques dans lesquels des minéralisations de
type discordances ont été reconnues. Bien qu’il soit distinct du point de vue génétique, le gisement d’Olympic
Dam est donné pour comparaison, car il constitue le plus gros gisement connu dans lemonde.
Rappels bibliographiques
23
On peut alors distinguer trois sous-types de minéralisation en fonction de la localisation des
corps minéralisés (Jefferson et al. 2007b): (1) les minéralisations encaissées dans le socle
(gisement de Collins Bay par exemple), (2) les minéralisations distribuées dans des failles ou
des corridors de fractures la long de la discordance basale (gisement de Cigar Lake par
exemple) et (3) les minéralisations situées au dessus de la discordance (minéralisation dite
perchée), Figure 3-6. Les différents sous-types de minéralisation ne sont pas exclusifs. Ils
peuvent être associés dans un même gisement comme c’est le cas à Key Lake ou à Shea
Creek (Andrade 2002; Thomas et al. 2000). Les profondeurs sous la discordance à laquelle se
font les nouvelles découvertes de minéralisation dans le socle sont de plus en plus
importantes. Elles atteignent plus de 300m dans le bassin d’Athabasca (Shea Creek) et plus de
200m dans le gisement de Jabiluka (Australie).
Il est également possible de déterminer deux sous ensembles de minéralisation sur une base
de critères géochimiques : (1) la minéralisation monométallique est essentiellement constituée
de’uraninite. Elle est surtout encaissée dans le socle et est globalement pauvre en terres rares
légères (2) La minéralisation polymétallique est généralement encaissée dans le grès ou
localisée à la discordance. Elle se caractérise par un minerai riche en Ni, Co, Cu, Mo et en
terres rares légères, Figure 3-7.
Rappels bibliographiques
24
Figure 3-6 : Exemples de gisements illustrant les trois styles de minéralisation dans des gisements d’uranium
associées aux discordances d’après (Andrade 2002; Thomas et al. 2000; Jefferson et al. 2007b).
Rappels bibliographiques
25
Figure 3-7 : Schéma simplifié des environnements géologiques associées aux gîtes mono- et polymétalliques
dans les systèmes de type discordance d’après (Jefferson et al. 2007b; Sibbald et al. 1976; Hoeve and Sibbald
1978; Hoeve and Quirt 1984; Ruzicka 1996; Thomas et al. 2000; Tourigny et al. 2007).
3.4. Contrôle structural régional et local des minéralisations
Quelles que soient les typologies de minéralisation rencontrées, il existe un fort contrôle
structural de leur mise en place. A l’échelle régionale, ce contrôle s’exerce par de grandes
structures souvent héritées des phases de structuration Archéennes et Paléoprotérozoiques qui
sont exprimées sous la forme de zones mylonitiques graphiteuses (Athabasca, bordure Sud
ouest du Thelon) ou non (Nord Est du Thelon, Kombolgie) (Wilde and Wall 1987). C’est le
cas par exemple de la structure P2 le long de laquelle se distribuent les gisements de Cigare
Lake et McArthur River ou bien celle du « Saskatoon Lake Conductor » qui contrôle les
minéralisations du district de Shea Creek dans les parties est et ouest du bassin de
l’Athabasca respectivement.
Ces zones de déformation majeure du socle ont ensuite été réactivées lors de l’histoire
tectonique post-dépôt sédimentaire. A cela s’ajoute l’ensemble des réseaux de failles
subsidiaires qui forment des zones favorables pour la circulation des fluides et dont le rôle
Rappels bibliographiques
26
dans le contrôle de la minéralisation à été mis en évidence très tôt sur la mine de Rabbit lake
(Hoeve and Sibbald 1978; Hoeve et al. 1980), à Cigare lake (McGill et al. 1993), à Cluff Lake
(Beaudemont and Fedorowich 1996) ou bien encore à Shea Creek par le biais de « couloirs
brèchiques » (Lorilleux 2001) pour ne citer que quelques exemples.
3.5. Typologie des altérations
La manifestation des interactions fluides roches guidées par les structures et responsables de
la formation des minéralisations, est le témoin d’échanges et de circulations entre le bassin et
les roches de socle sous jacentes. Les conditions nécessaires sont celles décrites par les
auteurs du modèle de type diagénétique-hydrothermal dans lequel les saumures de bassins
sont à la fois les vecteurs de l’altération et de la minéralisation (Hoeve and Sibbald 1978;
Hoeve and Quirt 1984). Ces processus sont mis en œuvre lors des phases de réactivation
permettant la mise en circulation de ces fluides, alors que le bassin est soumis à une diagenèse
poussée (Pagel 1975).
La minéralogie et la géochimie des altérations des roches encaissantes des gisements
d’uranium associées aux discordances ont fait l’objet d’études au Canada, principalement
dans l’Athabasca et dans une moindre mesure dans le Thelon, et en Australie dans l’Alligator
River afin de décrire et comprendre les zonalités des gisements et de les comparer (Hoeve and
Quirt 1984; Miller and LeCheminant 1985; Kotzer and Kyser 1995; Kyser et al. 2000;
Beaufort et al. 2005; Renac et al. 2002; Cuney et al. 2003; Percival and Kodama 1989),
Figure 3-8.
On remarque alors une minéralogie des halos d’altération associés aux minéralisations
uranifères très semblable pour les trois bassins Paléoproterozoiques avec un assemblage à
illite ( interstratifié illite-smectite) sudoite (chlorite Al-Mg) clinochlore (chlorite Mg)
chlorite Fe-Mg phosphate sulfate d’alumium hydratés apatite en différentes
Rappels bibliographiques
27
proportions selon que l’on considère les grès, la discordance ou bien le socle. On note
également la présence de la dravite parfois en abondance ( tourmaline magnésienne).
Figure 3-8 : Paragenèse minérales associées aux minéralisations de types discordances dans les Bassins de la
Kombolgie, du Thelon et de l’Athabasca in (Jefferson et al. 2007b) d’après (Kyser et al. 2000; Polito et al. 2004;
Polito et al. 2005; Creaser and Stasiuk 2007)
Cette minéralogie des phases d’altération est fortement dominée par l’illite dont les halos
peuvent s’étendre à plusieurs centaines de mètres des minéralisations aussi bien dans le socle
que dans la couverture sédimentaire. Cette altération se manifeste par une forte desilicification
et une déstabilisation des minéraux initialement présents, principalement les aluminosilicates,
et aussi les minéraux accessoires (zircon, monazite, tourmaline, etc). Ces processus induisent
une déstabilisation des minéraux ferromagnésien du socle tels la biotite ou l’amphibole et se
manifeste sous la forme d’un blanchiment des roches ainsi altérées (Hoeve and Quirt 1984).
Rappels bibliographiques
28
Enfin, le potassium libéré par la dissolution des aluminosilicates du socle peut alors alimenter
l’illitisation des kaolinites présentes dans la couverture gréseuse.
De plus une zonalité apparaît, dans la répartition des polytypes de l’illite autour des corps
minéralisés (Laverret 2002) et la distribution spatiale des différentes chlorites Fe-Mg ou Al-
Mg (sudoite) (Hoeve and Quirt 1984). Cette zonation minéralogique est contrôlée par
plusieurs facteurs tels que l’évolution de la composition du fluide hydrothermal, la durée des
phénomènes d’interaction fluide-roche ou bien encore l’hydrodynamisme du système.
Enfin la distribution spatiale des altérations argileuses s’exprime schématiquement sous la
forme de deux typologies selon que l’expression de l’altération est prédominante dans le socle
ou dans la couverture, Figure 3-9. Ces distributions donnent lieu à une interprétation selon les
modes « egress » ou « ingress » (Quirt 2003). Le mode « egress » se distingue par une large
enveloppe à illite sudoite largement exprimée dans la couverture gréseuse entourant une
zone plus riche en sudoite et un cœur riche en chlorite ferromagnésienne, biotite et sudoite qui
semble s’enraciner sur la structure guidant l’altération. Le mode « ingress » affecte
essentiellement le socle. Il montre une zonalité inverse des altérations avec au cœur un
assemblage à illite sudoite entouré d’un halo à sudoite illite puis d’une zone à chlorite
Fe-Mg, biotite et sudoite. On peut éventuellement considérer que ce dernier assemblage,
dominé par les minéraux métamorphiques du socle est l’expression plus distale de l’altération.
Chacune de ces altérations est considérée comme un marqueur du passage des fluides soit du
socle vers la couverture (egress) soit de la couverture vers le socle (ingress).
Rappels bibliographiques
29
Figure 3-9 : Schéma des types de minéralisations "egress" et "ingress" in (Jefferson et al. 2007b) d’après (Hoeve
and Quirt 1984; Sibbald 1985; Fayek and Kyser 1997)
Rappels bibliographiques
30
3.6. Quelques repères chronologiques : âges des minéralisations, événements
thermiques (diagenèse & intrusions) et contexte géodynamique en lien avec les
minéralisations d’uranium de l’Athabasca et du Thelon
Figure 3-10 : Mise en relation des grands événements tectoniques à l’échelle du bouclier avec les âges des
minéralisations uranifère dans le bassin de l’Athabasca, (Alexandre et al. 2009)
Rappels bibliographiques
31
Les travaux de datation des minéralisations sont toujours complexes de part la forte réactivité
chimique de l’uraninite et sa propension à recristalliser au cours des temps géologiques. Les
différentes études géochronologiques permettent néanmoins de caler l’âge des minéralisations
avec un certain nombre de moments clefs de la géodynamique du craton canadien
(orogenèses, magmatisme, ritfing, diagenèse), Figure 3-10.
Les principaux âges de mise en place des minéralisations uranifères du le bouclier canadien
s’étalent entre 1800 et 900 Ma. Pour les minéralisations de l’Athabasca, ils peuvent être
résumés comme suit: (1) 1780 20 Ma pour les veines de Beaverlodge (Koeppel 1967), (2)
1586 15 (Alexandre et al. 2009) 151922 et 1486 9 Ma U/Pb à McArthur River et
1467 47 à Cigare Lake parmi les plus anciennes mesurées a la sonde ionique dans
l’Athabasca (Fayek et al. 2002), (3) 1329 17 Ma à Key lake (Cumming and Krstic 1992), (4)
1275 22 à Shea Creek, ou bien encore 900 Ma (Fayek et al. 2002). Ces datations
n’excluent pas la possibilité de remobilisations plus tardives d’une partie de la minéralisation
sous la formes de fronts d’oxydo-réduction datés jusqu’à moins de 400 Ma (Mercadier et al.
2010).
A Shea Creek, il existe une bonne concordance entre les âges obtenus sur les illites du halo
d’altération (1453 2, 1330 20 et 1235 Ma ) et ceux obtenus sur les uraninites du gisement
(Laverret et al. 2010).
Comme ces auteurs l’on proposé il est possible de relier ces différents âges d’une part à
l’événement diagénétique ayant affecté l’ensemble du bassin au alentour de 1500 Ma
(contemporain de la fin de l’orogène Mazatzal et des minéralisations les plus anciennes) et
d’autre part aux remobilisations qui ont pu être contemporaines d’autres phases tectoniques
tels que les orogènes Bertoud et Grenville respectivement vers 1400 et 1100 Ma et les dykes
de Mackenzie à 12672 Ma (LeCheminant and Heaman 1989), la formation et dislocation de
Rappels bibliographiques
32
la Rhodinia ou de la Pangée (1000, 700 et 300 Ma), ou bien enfin des phénomènes d’uplift et
d’érosion pour les fronts redox mis en place vers 400 Ma.
Les données de datations de la littérature sont bien moins abondantes pour les gisements du
bassin du Thelon. On peut toutefois mentionner des âges à 1403 10 Ma U/Pb (Farkas
1984) sur roche totale pour Kiggavik ainsi que des âges K/Ar sur illite à 1386 24 Ma, 1362
21 Ma (Miller and LeCheminant 1985) ou 1073 Ma (Miller 1981). Des âges plus récents à
environ 1200 Ma ont été obtenu sur la minéralisation massive d’End, échantillonné en 2010 et
confiée à M. Brouand pour analyse à la microsonde ionique. On retrouve des gammes d’âges
concordantes entre évènements de minéralisation et d’altération. On peut noter des âges pafois
proches pour les minéralisations en uranium associées à l’Athabasca et au Thelon.
Enfin l’âge de la sédimentation ou du début de la diagenèse à été contraint à 1730-1750 Ma
pour le bassin d’Athabasca par la datation des derniers épisodes métamorphiques (Orrell et al.
1999) et à 17206 Ma et 1667 5 Ma par datation Pb/Pb sur apatite diagénétique en ciment à
la base du Thelon (Miller et al. 1989) et datation in situ U/Pb sur fluorapatite (Davis et al.
2011) respectivement pour le bassin du Thelon .
3.7. Géologie des gisements d’uranium du district de Kiggavik
3.7.1. Localisation et bref historique des travaux d’exploration
Le projet Kiggavik anciennement dénommé Lone Gull est situé à 80 km à l’ouest du hameau
Inuit de Baker Lake, au Nunavut. Les premiers travaux d’exploration de ce gisement qui est
activement prospecté depuis quelques années, remontent à 1974 lors de la découverte de
minéralisations uranifères sub-affleurantes à Kiggavik s.s lors d’une campagne de radiométrie
aéroportée menée par Urangesellschaft Canada (UG). Ceci conduira à la découverte de la
lentille de Main Zone en 1977 avec un premier sondage intersectant 35m de roches altérées
contenant 1% U3O8 (Fuchs et al. 1986). L’actuel camp d’exploration des équipes d’AREVA
Rappels bibliographiques
33
Resources Canada (ARC) se situe à quelques centaines de mètres à l’Est de cette zone, à
l’emplacement de l’ancien camp Schutlz-Sissons South d’UG, Figure 3-11.
Figure 3-11 : Camp d’exploration de Kiggavik, crédit photo aérienne : AREVA Resources Canada
Le district comprend plusieurs zones minéralisées d’importance économique ainsi que de
nombreux prospects ou zones à fort potentiel en cours de développement ou de test. Ainsi du
Nord Est au Sud Ouest des propriétés formant le projet on retrouve Kiggavik ss., la
découverte initiale (1974), Bong (1986) , End (1987), et enfin Andrew (SW Grid, 1988) puis
Jane (1993), l’ensemble de ces zones minéralisées totalise un contenu de ressources
historiques d’approximativement 58000t d’uranium. Le projet comprend deux grandes zones
non contigües de permis d’exploration composées de St Tropez au Nord et de Kiggavik au
Sud, Figure 3-12 et 3-15.
A l’échelle régionale, les guides de prospection suivis ont été tout d’abord, la géophysique
avec la combinaison de données de résistivité et de gravimétrie permettant de localiser les
structures et les zones altérées (Hasegawa et al. 1990). Par la suite de proche en proche,
l’exploration a été menée en suivant le contact entre les bancs de quarztites massifs (archéen
Rappels bibliographiques
34
ou Paléoproterozoïques) et les métagraywackes Archéan du Woodburn Lake Group (WLG).
Ce contact étant lui-même souligné par de puissantes zones de brèches à remplissage de
quartz, souvent associées à une forte hématitisation. Ces brèches sont par ailleurs recoupées
en sondages dans l’ensemble des zones minéralisées de Kiggavik ou elles délimitent souvent
deux zones de minéralisations de part et d’autre du couloir de brèche à remplissage de quartz.
Figure 3-12 : Carte des droits miniers pour les projets ARC de la bordure Sud Ouest du bassin du Thelon
(Kiggavik et St Tropez) et localisation du camp d’exploration de Kiggavik (Morisson et al. 2012)
Rappels bibliographiques
35
3.7.2. Séquence lithostratigraphique de la bordure Sud Est du bassin du
Thelon et position des minéralisations
L’encaissant des minéralisations et principalement formé par des métagraywackes Archéens
(2711 3 Ma) appartenant au groupe de Woodburn, et dans une moindre mesure dans des
métagranodiorites (assignées au méso-Archéen) mis eu contact avec les métagraywackes par
le biais d’une structure mylonitique plate, parallèle à la foliation, Figure 3-13. Les granites et
syénites Hudsonienne ou Nuetlin peuvent être minéralisés plus rarement. Un lien génétique
entre la minéralisation en uranium et les roches intrusives été évoqué dans les travaux
historiques sur le gisement de Kiggavik (Weyer et al. 1987). Cette proximité spatiale entre
roches intrusives et minéralisations uranifères est exprimée à Kiggavik ss, à End Grid et à
Andrew Lake. Les roches intrusives sont majoritairement représentées par des granites et des
syénites hudsoniennes souvent riches en fluorine (1840-1830 Ma) sous la forme de dykes
sécants sur la foliation horizontale ou de sills entourés d’un fin halo de cornéennes (Jeffrey et
al. 2010; Peterson et al. 2002). Les intrusions de l’épisode Nuetlin et leur équivalent
volcanique (Pitz rhyolite) datés à à 1750 Ma sont présents à l’affleurement à Andrew lake et
sont fréquemment recoupées en sondage sous la forme de dykes de granite porphyrique à
texture rapakivi.
Les minéralisations semblent s’enraciner plus en profondeur vers le SW du faisceau
minéralisé. De Kiggavik jusqu’à Andew, la minéralisation est trouvée à l’affleurement, dans
les métagraywackes altérés. A Jane, elle est encaissée dans des orthogneisses sous la forme de
veines à remplissage de pechblende. Les quartzites qui séparent les lentilles supérieures et
inférieures du gisement de Kiggavik sont également rencontrés au dessus de la zone
minéralisée à Bong, Figure 3-14.
On peut enfin noter que les contacts entre les unités lithologiques ou les structures brêchiques
forment souvent des zones favorables au dépôt des lentilles minéralisées. C’est tout
Rappels bibliographiques
36
particulièrement le cas au contact entre les roches intrusives et les méta-graywackes ou autour
des brèches à remplissage de quartz que l’on peut l’observer à Bong ou End.
Figure 3-13 : Coupe géologique dans une section du gisement d’Andrew Lake (données UG/AREVA Resources
Canada Inc.)
Rappels bibliographiques
37
Figure 3-14 : Coupe du gisement de Center Zone à Kiggavik montrant la position des minéralisations par rapport
aux bancs massifs de quartzite (Weyer 1992)
3.7.3. Structuration ductile et déformation fragile
Comme il a été présenté précédement, un lien fort est établi entre les structures et les
minéralisations dans les gisements de type discordance. A Kiggavik l’histoire tectono-
métamorphique polyphasée et complexe a contribué au développement des discontinuités qui
sont les drains préférentiels des fluides minéralisateurs. On reprendra rapidement ici les
résultats établis par les travaux de terrains et les analyses structurales de Jean-Louis Feybesse
et Nicolas Flotté réalisés en 2009, 2010 autour de Kiggavik (Flotté 2009; Feybesse 2010).
- La déformation ductile
On peut identifier deux grandes phases tectoniques tardi-archéennes avec (1) la mise en place
de plis à vergence NW et NNW dans le socle méso-Archeén puis (2) la mise en place de
nappes de chevauchement exprimée par une zone mylonitique faiblement pentée à la base des
Rappels bibliographiques
38
métasédiments du Woodburn group et le développement d’une foliation sub-parallèle au
contact mylonitique que l’on retrouve communément dans la zone de Kiggavik (Beaudemont
1995).
Une troisième phase de déformation est caractérisée par le developpement d’une zone de
cisaillement Nβ70 à linéation d’étirement E-W. Elle est principalement observée à la base des
quartzites et elle constitue une des discontinuités majeures de la zone de Kiggavik avec pour
conséquence l’entrainement des quartzites massifs dont la position dans la pile lithologique
(elles reposent sur les roches du Woodburn Group par le jeu d’une zone mylonitiques
faiblement pentée vers le Nord) fait toujours l’objet de débat. Cette phase de déformation est
attribuée à la phase hudsonienne (Paléoproterozoique)
- Déformation fragile
Plusieurs familles de failles sont identifiées avec à l’échelle régionale. Il s’agit de la faille
du Thelon, Judge Sisson lake ou leur parallèles dont l’expression est visible aussi bien à
l’affleurement qu’en sondage autour des zones End Grid et Bong. On a alors, pour structure
de premier ordre, la faille d’Andrew lake, d’orientation NE-SW et de cinématique interprétée
dextre par la suite réactivée en senestre. Les minéraliations d’Andrew et Jane se trouvent
distribuées le long de cette structure. Le second ordre de faille est d’orientation globale
WNW-ESE (N70 à N100) avec une cinématique dextre. Ces dernières structures sont
soulignées par une forte cataclase et de puissantes zones de brèches à remplissage de quartz.
Elles présentent également une hématitisation intense qui affecte le socle métamorphique, les
intrusifs (hudsonien et Nuetlin) ainsi que les sédiments du Thelon.
A ces failles (et les brêches tectoniques associées) sont reliés un ensemble de structures
dextres redressées d’orientation N1β0-N130, formant parfois des zones de relais avec les
Rappels bibliographiques
39
structures N70 et un autre ensemble de failles normales Est- Ouest faiblement pentées vers le
Nord.
Enfin une série de failles tardives sont venues modifier la géométrie des éléments structuraux
précédents et affecter les sédiments des bassins de Baker lake et de Wharton. Il s’agit, soit de
failles Nord-Sud, à N30 senestres, soit de failles N160 dextre (Rainbird and Hadlari 2000).
Ces structures tardives ne se limitent pas à la zone de Kiggavik. Elles s’expriment dans
l’ensemble de la province de Rae. Elles ont été observées dans le gisement de Sue C dans la
partie est du bassin d’Athabasca (Flotté et Feybesse, 2008).
Rappels bibliographiques
40
Figure 3-15 : Carte géologique révisée de la bordure Sud Ouest du Thelon et synthèse stratigraphique des formations Archéennes d’après (Jefferson et al. 2011)
Références
41
4. Références
Alexandre P, Kyser K, Thomas D, Polito P, Marlat J (2009) Geochronology of unconformity-related uranium deposits in the Athabasca Basin, Saskatchewan, Canada and their integration in the evolution of the basin. Miner Deposita 44:41-59. doi: 10.1007/s00126-007-0153-3.
Andrade N (ed) (2002) Geology of the Cigar Lake uranium deposit. Geological Association of Canada - Mineralogical association of Canada, Saskatoon, SK.
Ashton KE (1988) Precambrian Geology of the Southeastern Amer Lake Area (66H/1), Near Baker Lake, N.W.T. Queens University.
Aspler LB, Wisotzek IE, Chiarenzelli JR, Losonczy MF, Cousens BL, McNicoll VJ, Davis WJ (2001) Paleoproterozoic intracratonic basin processes, from breakup of Kenorland to assembly of Laurentia: Hurwitz Basin, Nunavut, Canada. Sedimentary Geology 141–142:287-318. doi: http://dx.doi.org/10.1016/S0037-0738(01)00080-X.
Aspler LB, Chiarenzelli JR, McNicoll VJ (2002) Paleoproterozoic basement-cover infolding and thick-skinned thrusting in Hearne domain, Nunavut, Canada: intracratonic response to Trans-Hudson orogen. Precambrian Research 116:331-354. doi: http://dx.doi.org/10.1016/S0301-9268(02)00029-3.
Bagas L (2004) Proterozoic evolution and tectonic setting of the Northwest Paterson Orogen, Western Australia. Precambrian Research 128:475-496.
Battey GC, Miezitis Y, McKay AD (1987) Australian uranium resources. Bureau of Mineral Resources, Geology and Geophysics, pp 69.
Beaudemont D (1995) Sisson Project, regional tectonics and structural control of mineralization, report on summer 1995 inverstigation. Cogemac Inc, pp 41.
Beaudemont D, Fedorowich J (1996) Structural control of uranium mineralization at the Dominique-Peter deposit, Saskatchewan, Canada. Economic Geology 91:855-874.
Beaufort D, Patrier P, Laverret E, Bruneton P, Mondy J (2005) Clay Alteration Associated with Proterozoic Unconformity-Type Uranium Deposits
in the East Alligator Rivers Uranium Field, Northern Territory, Australia. Economic Geology v. 100:pp. 515–536.
Betts PG, Giles D, Schaefer BF (2008) Comparing 1800 – 1600 Ma accretionary and basin processes in Australia and Laurentia: Possible geographic connections in Columbia. Precambrian Research 166:81-92. doi: http://dx.doi.org/10.1016/j.precamres. 2007.03.007.
Corrigan D, Galley AG, Pehrsson S (2007) Tectonic evolution and metallogeny of the southwestern Trans-Husdon Orogen In: Goodfellow WD (ed) Mineral Deposits of Canada: A synthesis of Major Deposit-Types, District Metallogeny, the Evolution of Geological Provinces, and Exploration Methodes. Geological Association of Canada, Mineral Deposits Division, pp 881-902.
Creaser RA, Stasiuk LD (2007) Depositional age of the Douglas Formation, northern Saskatchewan, determined by Re-Os geochronology In: Jefferson CW (ed) EXTECH IV: Geologyand Uranium EXploration TECHnology of the Proterozoic AthabascaBasin, Saskatchewan and Alberta. Geological Survey of Canada, pp 341-346.
Références
42
Cumming GL, Krstic D (1992) The age of unconformity related uranium mineralization in the Athabasca Basin, northern Saskatchewan. Canadian Journal of Earth Sciences 29:1623-1639.
Cuney M, Brouand M, Cathelineau M, Derome D, Freiberger R, Hecht R, Kister P, Lobaev V, Lorilleux G, Peiffert C, Bastoul AM (2003) What parameters control the high grade-large tonnage of the Proterozoic unconformity related uranium deposits? In: Cuney M (ed) International conference on uranium geochemistry. Université Henri Poincaré, Nancy, pp 123-126.
Davis WJ, Gall Q, Jefferson CW, Rainbird RH (2011) Fluorapatite in the Paleoproterozoic Thelon Basin: Structural-stratigraphic context, in situ ion microprobe U-Pb ages, and fluid-flow history. Geological Society of America Bulletin 123:1056-1073. doi: 10.1130/b30163.1.
Duebendorfer EM, Houston RS (1987) Proterozoic accretionary tectonics at the southern margin of the Archean Wyoming craton. Geological Society of America Bulletin 98:554-568.
Duebendorfer EM, Chamberlain KR, Jones CS (2001) Paleoproterozoic tectonic history of the Cerbat Northwestern Arizona:Implications for crustal Southwestern United States. Geological Society of America Bulletin 113:575-590.
Eriksson PG, Martins-Neto MA, Nelson DR, Aspler LB, Chiarenzelli JR, Catuneanu O, Sarkar S, Altermann W, Rautenbach CJdW (2001) An introduction to Precambrian basins: their characteristics and genesis. Sedimentary Geology 141–142:1-35. doi: http://dx.doi.org/10.1016/S0037-0738(01)00066-5.
Farkas A (1984) Mineralogy and host rock alteration of the Lone Gull deposit Internal report. Urangesellschaft, Frankfurt am Main, pp 45.
Fayek M, Kyser K (1997) Characterization of multiple fluid events and rare-earth-element mobility associated with formation of unconformity-type uranium deposits in the Athabasca Basin, Saskatchewan. The Canadian Mineralogist 35:627-658.
Fayek M, Kyser K, Riciputi LR (2002) U and Pb isotope analysis of uranium minerals by ion microprobe and the geochronology of the McArthur River and Sue zone uranium deposits, Saskatchewan, Canada. Canadian Mineralogist 40:1553-1569.
Feybesse J-L (2010) Sequence of structural events in the Kiggavik district ( Nunavut, Canada): The uranium mineralization in its geological and tectonic setting and structural control on the ore bodies geometry. AREVA BGM/DGS.
Flotté N (2009) End Grid geological and structural study. AREVA Resources Canada, Saskatoon.
Fuchs HD, Hilger W, Prosser E (eds) (1986) Geology and exploration history of the Lone Gull property. CIM.
Gandhi SS (1995) An overview of the exploration history and genesis of Proterozoic uranium deposits in the Canadian Shield. Exploration and Research for Atomic Minerals 8:1-47.
Gandhi SS (2006) Significant unconformity-associated uranium deposits of the Athabasca Basin, Saskatchewan and Alberta and selected related deposits of Canada and the world In: GSC (ed) Open File 5005. pp (CD-ROM).
Hanmer S, Williams ML, Kopf C (1995) Striding-Athabasca mylonite zone: implications for the Archean and Early Proterozoic tectonics of the Western Canadian shield. Canadian Journal of Earth Sciences 32:178-196.
Hartlaub RP, Heaman LM, Ashton KE, Chacko T (2004) The Archean Murmac Bay Group: evidence for a giant Archean rift in the Rae Province, Canada. Precambrian Research 131:345-372.
Références
43
Hasegawa K, Davidson GI, Wollenberg P, Yoshimasa I (1990) Geophysical exploration for unconformity-related uranium deposits in the northeastern part of the Thelon Basin, Northwest Territories, Canada. Mining Geology 40:83-95.
Hills FA (1987) Tectonic environment of Precambrian quartz-pebble conglomerate uranium deposits formed along the southern margin of the Archean shield in North America In: Agency IAE (ed) Report of the working group on uranium geology organized by the International Atomic Energy Agency. Vienna, pp 453.
Hoeve J, Sibbald TII (1978) On the genesis of the Rabbit Lake and other unconformity-type uranium deposits in Northern Saskatchewan, Canada. Economic Geology 73.
Hoeve J, Sibbald TII, Ramaekers P, Lewry JF (1980) Athabasca basin unconformity-type uranium deposits : a special class of sandstone-type deposits? In: Ferguson J, Goleby AB (eds) Uranium in the Pine Creek Geosyncline. International Atomic Energy Agency, Vienna, pp pp. 575-594.
Hoeve J, Quirt D (1984) Mineralization and host rock alteration in relation to clay mineral diagenesis and evolution of the Middle-Proterozoic Athabasca basin, Northern Saskatchewan, Canada Saskatchewan Research Concil Technical report. Saskatchewan Reasearch Council, pp 197.
Hoffman PF (1988) United Plates of America, The Birth of a Craton: Early Proterozoic Assembly and Growth of Laurentia. Annual Review of Earth and Planetary Sciences 16:543-603. doi: doi:10.1146/annurev.ea.16.050188.002551.
Hoffman PF (1990) Subdivision of the Churchill Province and extent of the Trans-Hudson orogen In: Lewry JF, Stauffer MR (eds) The Early Proterozoic Trans-Hudson Orogen of North Amercia. Geological Survey of Canada Special Paper, pp 15-39.
Jefferson CW, Thomas DJ, Gandhi SS, Ramaekers P, Delaney G, Brisbin D, Cutts C, Portella P, Olson RA (2007a) Unconformity-associeted uranium deposits of the Athabasca Basin, Saskatchewan and Alberta EXTECH IV. pp 23-67.
Jefferson CW, Thomas DJ, Gandhi SS, Ramaekers P, Delaney G, Brisbin D, Cutts C, Quirt D, Portella P, Olson RA (2007b) Unconformity-associated uranium deposits of the Athabasca Basin, Saskatchewan and Alberta In: Goodfellow WD (ed) Mineral Deposits of Canada: A synthesis of Major Deposit-types, District Metallogeny, the Evolution of Geological Provinces, and Exploration Methods. Geological Association of Canada, Mineral deposits division, pp 273-305.
Jefferson CW, Pehrsson S, Peterson T, Chorlton L, Davis DW, Keating P, Gandhi SS, Fortin R, Buckle JL, Miles W, Rainbird RH, LeCheminant AN, Tschirhart V, Tschirhart P, Morris W, Scott J, Cousens B, McEwan B, Bethune K, Riemer W, Calhoun L, White J, MacIssac D, Leblon B, Lentz D, laRocque A, Shelat Y, Patterson J, Enright A, Stieber C, Riegler T (2011) Northeast Thelon region geoscience framwork-new maps and data for uranium in Nunavut In: Canada NR (ed). Geological Survey of Canada.
Jeffrey S, Peterson T, Jefferson CW, Cousens B (2010) Proterozoic (1.85-1.7 Gaà granitoid rocks and uranium in the Baker Lake -Thelon Basin region, Nunavut GeoCanada2010. Calgary.
Karlstrom KE, Bowring SA (1988) Early Proterozoic assembly of tectonostratigraphic terranes in Southwestern North America. J Geol 96:561-576.
Karlstrom KE, Åhäll K-I, Harlan SS, Williams ML, McLelland J, Geissman JW (2001) Long lived (1.8-1.0 Ga) convergent orogen in southern Laurentia, its extensions to Australia and Baltica, and implications for refining Rodinia. Precambrian Research 111:5-30.
Kerrich R, Goldfarb RJ, Richards JP (2005) Metallogenic Provinces in an Evolving Geodynamic Framework. Economic Geology 100th Anniversary Volume:1097-1136.
Koeppel V (1967) Age and history of uranium mineralization of the Beaverlodge area, Saskatchewan. Geological Survey of Canada, pp 111.
Références
44
Kotzer TG, Kyser TK (1995) Petrogenesis of the Proterozoic Athabasca Basin, northern Saskatchewan, Canada, and its relation to diagenesis, hydrothermal uranium mineralization and paleohydrogeology. Chemical Geology 120:45-89. doi: http://dx.doi.org/10.1016/0009-2541(94)00114-N.
Kyser K, Hiatt EE, Renac C, Durocher K, Holk G, Deckart K (2000) Diagenetic fluids in Paleo and Meso-proterozoic sedimentary basins and their implications for long protracted fluid histories In: Kyser K (ed) Fluids and Basin Evolution. Mineralogical Association of Canada, pp 225-258.
Laverret E (2002) Evolution temporelles et spatiales des altérations argileuses des gisements d'uranium sous discordance, secteur de Shea Creek (basin d'Athabasca, Canada). Université de Poitiers, pp 192.
Laverret E, Clauer N, Fallick A, Mercadier J, Patrier P, Beaufort D, Bruneton P (2010) K–Ar dating and δ18O–δD tracing of illitization within and outside the Shea Creek uranium prospect, Athabasca Basin, Canada. Applied Geochemistry 25:856-871. doi: http://dx.doi.org/10.1016/j.apgeochem.2010.03.004.
LeCheminant AN, Heaman LM (1989) Mackenzie igneous events, Canada: Middle Proterozoic hotspot magmatism associated with ocean opening. Earth and Planetary Science Letters 96:38-48. doi: http://dx.doi.org/10.1016/0012-821X(89)90122-2.
Lorilleux G (2001) Les brèches associées aux gisements d'uranium de type discordance du bassin d'Athabasca, Saskatchewan, Canada Institut National Polytechnique de Lorraine. Université Henri Poincaré, Vandoeuvre les Nancy.
Macdonald R (1980) Mineralogy and geochemistry of a Precambrian regolith in the Athabasca Basin. University of Saskatchewan, Saskatoon, pp 151.
McGill B, Marlat J, Matthews RB, Sopuck V, Homenuik L, Hubergtse J (1993) The P2 North uranium deposit, Saskatchewan, Canada. Exploration Mining Geology 2:321-331.
Mercadier J, Cuney M, Cathelineau M, Lacorde M (2010) U redox and kaolinisation in basement-hosted unconformity-related U ores of the Athabasca Basin (Canada): late U remobilisation by meteoric fluids. Miner Deposita 46:105-135.
Miller AR (1981) Lone Gull deposit district of Keewatin, N.W.T. Geological Survey of Canada.
Miller AR, LeCheminant AN (1985) Geology and uranium metallogeny of Proterozoic supracrustal successions, central District of Keewatin, N.W.T with comparisons to northern Saskatchewan Geology of uranium deposits. Canadian Institute of Mining and Metalurgy, pp 167-185.
Miller AR, Cumming GL, Krstic D (1989) U-Pb, Pb-Pb, and K-Ar isotopic study and petrography of uraniferous phosphate-bearing rocks in the Thelon Formation, Dubawnt Group, Northwest Territories, Canada. Canadian Journal of Earth Sciences 26:867-880.
Molnar P, Houseman GA, Conrad CP (1998) Rayleigh-Taylor instability and convective thinning of mecanically thickened lithosphere:effects of non-linear viscosity decreasing exponentially with depth and horizontal shortening of the layer. Geophys J Int 133:568-584.
Morisson D, McCallum B, Zunti D, Jackson K, Carter C, Calayan N, Richard Y (2012) Kiggavik Project Field Program 2012 Annual Report In: Stumborg N (ed). AREVA Resources Canada Inc., Saskatoon.
Orrell SE, Bickford ME, Lewry JF (1999) Crustal evolution and age of thermotectonic reworking in the western hinterland of the Trans-Hudson Orogen, northern Saskatchewan. Precambrian Research 95:187-223.
Références
45
Pagel M (1975) Détermination des conditions physico-chimique de la silicification diagénétique des grès Athabasca (Canada) au moyen des inclusions fluides. Comptes Rendus de l'académie des Sciences Paris 280:2301-2304.
Percival JB, Kodama H (1989) Sudoite from Cigar Lake, Saskatchewan. Canadian Mineralogist 27:633-641.
Peterson TD, Van Breemen O, Sandeman H, Cousens B (2002) Proterozoic (1.85-1.75 Ga) igneous suites of the Western Churchill Province: granitoid and ultrapotassic magmatism in a reworked Archean hinterland. Precambrian Research 119:73-100.
Polito P, Kyser K, Thomas DJ, Marlat J, Dreaver G (2005) Re-evaluation of the Petrogenesis of the Proterozoic Jabiluka unconformity-related uranium deposit, Northern Territory, Australia. Miner Deposita 40:257-288.
Polito PA, KYSER TK, Marlatt J, Alexandre P, Bajwah Z, Drever G (2004) Significance of Alteration Assemblages for the Origin andEvolution of the Proterozoic Nabarlek Unconformity-Related Uranium Deposit,Northern Territory, Australia. Economic Geology 99:113-139. doi: 10.2113/gsecongeo.99.1.113.
Quirt D (2003) Athabasca unconformity type uranium deposits: one deposit type with many variations. In: Cuney M (ed) Uranium Geochemistry International Conference. Nancy, France, pp 309-312.
Rainbird RH, Hadlari T (2000) Revised stratigraphy and sedimentology of the Paleoproterozoic Dubawnt Supergroup and the Northern Margin of Baker Lake Basin, Nuanvut Current Research. Geological Survey of Canada, pp 9.
Rainbird RH, Hadlari T, Aspler LB, Donaldson JA, LeCheminant AN, Peterson TD (2003) Sequence stratigraphy and evolution of the Paleoproterozoic intracontinental Baker Lake and Thelon basins, western Churchill Province, Nunavut, Canada. Precambrian Research 125:21-53.
Rainbird RH, Stern RA, Rayner N, Jefferson CW (2006) Ar-Ar and U-Pb geochronology of a late Paleoproterozoic rift basin: support for a genetic link with Hudsonian orogenesis, western Chruchill Province, Nunavut, Canada. The Journal of Geology 114:1-17.
Rainbird RH, Davis WJ (2007) U-Pb detrital zircon geochronology and provenance of the late Paleoproterozoic Dubawnt Supergroup: Linking sedimentation with tectonic reworking of the western Churchill Province, Canada. Geological Society of America Bulletin 119:314-328. doi: 10.1130/b25989.1.
Ramaekers P, Catuneanu O (2004) Develoment and sequences of the Athabasca Basin, Early Proterozoic, Saskatchewan and Alberta, Canada In: Eriksson PG, Altermann W, Nelson DR, Mueller WU, Catuneanu O (eds) The Precambrian Earth: Tempos and Events. Elsivier, Amsterdam, Netherlands, pp 705-723.
Renac C, Kyser K, Durocher K, Dreaver G, O'Connor T (2002) Comparison of diagenetic fluids in the Proterozoic Thelon and Athabsca Basins, Canada: implications for protracted fluid histories in stable intracratonic basins. Can J Earth Sci 39:113-132.
Ruzicka VR (1993) Unconformity type uranium deposits In: Kirkham RV, Sinclair WD, Thorpe RI, Duke JM (eds) Mineral Deposit Modeling. Geological Survey of Canada, Ottawa, pp 125-149.
Ruzicka VR (1996) Unconformity-associated uranium In: Eckstrand OR, Sinclair WD, Thorpe RI (eds) Geology of Canadian Mineral Deposits. Geological Survey Of Canada, pp 197-210.
Sibbald TII, Munday RJC, Lewry JF (1976) The geolgical setting of uranium mineralization in northern Saskachtewan In: Dunn CE (ed) Uranium in Saskatchewan. Saskatchewan Geological Society, pp 51-98.
Sibbald TII (1985) Geology and genesis of the Athabasca Basin uranium deposits In: Macdonald R, Sibbald TII, Paterson DF (eds) Summary of Inversitgations 1985.
Références
46
Saskatchewan Geological Survey: Saskatchewan Energy and Mines Miscellaneous Report, pp 133-156.
Stauffer MR (1984) Manikewan and early proterozoic ocean in central Canada, its igneous history and orogenic closure. Precambrian Research 25:257-281.
Thomas DJ, Matthews RB, Sopuck V (2000) Athabasca Basin (Canada) unconformity-type uranium deposits: exploration model, current mine developpments and exploration directions In: Cluer JK, Price JG, Struhsacker EM, Hardyman RF, Morris CL (eds) Geology and Ore Deposits 2000:The Great Basin and Beyond, Geological Society of Nevada symposium proceedings. Reno, NV, pp 103-126.
Tourigny G, Quirt D, Wilson N, Wilson S, Breton G, Portella P (2007) Basement geology of the Sue C uranium deposit, McClean Lake area, Saskatchewan In: Jefferson CW, Delaney G (eds) EXTECH IV:Geology and uranium EXploration TECHnology of the Proterozoic Athabsca Basin, Saskatchewan and Alberta. Geological Survey of Canada, Mineral Deposits division, pp 229-248.
Weyer H-J, Friedrich G, Bechtel A, Ballhorn RK (1987) The Lone Gull uranium deposit-New geochemical and petrological data as evidence for the nature of the ore bearing solutions Metallogenesis of uranium deposits. IAEA, Vienna.
Weyer H-J (1992) Die uraniagnerstätte Kiggavik, Nordwesterritorien, Kanada Fakultät für Bergbau, Hüttenwesen und Geowissenschaften. Rheinisch-Westfälischen Technischen Hochschule, Aachen, pp 223.
Wilde AR, Wall VJ (1987) Geology of the Nabarlek uranium deposit, Northern Territory, Australia. Economic Geology 82:1152-1168.
Zhao G, Wilde SA, Li S (2004) A Paleo-Mesoproterozoic supercontinent: assembly, growth and breakup. Earth-Science Reviews 36:678-686.
Echantillonnage
47
5. Echantillonnage
Tableau 5-1 : Description générale de l’échantillonnage de la zone de Kiggavik – St Tropez.
DrillHole Depth
(m) Samples Purpose
W97-4 191.1 18 Regional Alteration background
B1-94-1 224.3 9 "
BSE1 154.5 5 "
W-2 94.2 4 "
Bong51 300.6 4 carbonaceous material
Bong50 386.7 28 Reference in Bong prospect
Bong45 405.0 40 Reference in Bong prospect
Bong42 459.0 43 Reference in Bong prospect
Bong43 495.0 36 Reference in Bong prospect
Bong33 223.4 11 Reference in Bong prospect
Bong39 486.2 29 Reference in Bong prospect
Bong26 225.6 8 Reference in Bong prospect
Bong24 312.4 17 Reference in Bong prospect
Bong8 232.6 16 Reference in Bong prospect
Bong6 204.9 4 Reference in Bong prospect
BongExt2 177.1 9 Alteration without mineralisation
SW8 191.1 17 Reference in Andrew deposit
And10-01 387.0 38 "
End09-11 378.8 15 Reference in End deposit
End09-10 377.6 17 Reference in End deposit
End09-09 393.0 20 Reference in End deposit
End09-08A 347.4 18 Reference in End deposit
End09-07 348.6 10 Reference in End deposit
End09-05 272.0 16 Reference in End deposit
End09-04 420.0 35 Reference in End deposit/Mineralization
End09-03 436.2 18 Reference in End deposit
End09-02 465.0 13 Reference in End deposit
End13 230.7 9 alteration without mineralization
SL9 335.9 5 Sleek Area alteration without Umin
Th18 123.6 7 regional sandstones NE of Kiggavik
Outcrops
Granite Grid
7 basal Thelon Fm conglomeratic sandstones
St Tropez
7 basal Thelon Fm conglomeratic sandstones
Uno
1 Fluorite bearing granite
Andrew&End 10 quartz breccia & porphyitic rhyolite
Unconformity Lake 8 basal Thelon & Woodburn
Echantillonnage
48
A. L E SYSTEME D’ALTERATION DU FAISCEAU DE K IGGAVIK -
ANDREW L AKE ET SES RELATIONS AVEC LES
MINERALISATIONS EN URANIUM
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
49
1. Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
Thomas Riegler*, Jean-Luc Lescuyer***, Peter Wollenberg***
Dave Quirt*** and Daniel Beaufort**
Accepted in Canadian Mineralogist
*IC2MP, HydrASA / ERM, Université de Poitiers, CNRS UMR 7285, Bâtiment
B08, Rue Albert Turpin, 86022 Poitiers cedex, [email protected]
** IC2MP, HydrASA, Université de Poitiers, CNRS UMR 7285, Bâtiment B35,
Rue Michel Brunet, 86022 Poitiers cedex, [email protected]
***AREVA Mines & AREVA Ressources Canada, Tour AREVA, 1 place Jean
Millier 92084 Paris la Défense Cedex
1.1. Abstract
The Kiggavik project, located 70km west of Baker Lake (Nunavut) is a major uranium
exploration project in the Canadian arctic, with three significant basement hosted uranium
deposits (Kiggavik, End and Andrew) which spread along a NE-SW trend a few kilometers to
the south-eastern border of the Thelon Basin. These deposits are closely associated with
alteration zones in which clay minerals are abundant. At the scale of the whole structural
trend, the alteration paragenesis is composed of illite ± sudoite ± hematite ± aluminum
phosphates sulfates minerals (APS). Alteration petrography and mineral paragenesis are
similar to those identified in basement hosted uranium deposits related to Paleoproterozoic
unconformities in the Athabasca Basin (Canada) or the Alligator River (Australia). The
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
50
alteration haloes are characterized by two similar types of phyllosilicate assemblages
(dioctahedral micas or illite and chlorites) corresponding to a regional retrograde
metamorphic stage that was overprinted by hydrothermal alteration during the mineralization
event. These two assemblages can be distinguished on the basis of crystallographic and
chemical properties and mapping of structural parameters such as the variation of crystallinity
along the c-axis or the polytypes of phyllosilicates can been used as a vector to
mineralization. The crystal-chemistry of the hydrothermal phyllosilicates replacing the
previous metamorphic minerals indicates a release of iron. This last point is fundamental
regarding the occurrence of hematite in alteration zones and points out the potential effects of
iron redox state in the control of uranium precipitation during the hydrothermal event.
1.2. Introduction
The Kiggavik project (previously named Lone Gull), located 70km west of Baker Lake,
Nunavut hosts several significant uranium deposits and very prospective areas, with an overall
uranium content of approximately 50,000t U of historical resources (Jefferson et al. 2007).
The deposits and prospects are structurally controlled along a NE-SW trend and are
exclusively basement hosted in Late Archean metasediments. This rock package consists of
dominant meta-arkose (wacke) and minor quartzite and rhyolites (Miller and LeCheminant
1985) later intruded by a suite of igneous bodies including Hudsonian fluorite-bearing
granites, syenites and lamprophyres (Peterson et al. 2002). The northern end of the trend,
where the Kiggavik deposit is located lies two kilometers south of the unconformity between
the Archean basement the late Paleoproterozoic Thelon Formation sandstones (Miller et al.
1989). Sub-outcropping mineralization was first discovered in 1974 following an airborne
radiometric survey by Urangesellschaft Canada, then followed with ground resistivity and
gravity surveys in further exploration work to detect alteration zones (Fuchs et al. 1986,
Hasegawa et al. 1990). This target identification method has been successfully used and lead
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
51
to several additional discoveries along the trend indicating that alteration features where in
most cases spatially related to mineralized zones.
Following the trend toward the southwest are found the Bong prospect, the End and
Andrew deposits (Fig. 1-1). The last known mineralization southward of this 18 kilometer
long mineralized trend is the Jane prospect. The main structural feature and regional
pathfinder are kilometer long ENE-WSW faults showing an intense hydrothermal activity
with both hematization and quartz veining. The nature and origin of the hydrothermal
processes responsible for uranium mineralization and its associated alteration haloes are still
unclear at Kiggavik.
Initially, exploration was carried out to find high-grade uranium in a geological context
similar to the basement rocks underlying the late Paleoproterozoic Athabasca Basin in
Northern Saskatchewan. Alternative models favored hydrothermal systems partly related to
heat sources generated by the numerous intrusive bodies identified in the area (Weyer et al.
1987) but geochronology of pitchblende (bulk U/Pb) and illite (whole rock K/Ar) from altered
and mineralized metasediments showed younger but discordant with possible lead loss or late
remobilization ages respectively around 140310 Ma, (Farkas 1984) and 1386±24 Ma K/Ar
(Miller and LeCheminant 1985). Salinity of the basinal brines, stable isotopes on diagenetic
clays and geochronology in the Thelon and Athabasca Basins had highlighted similar
diagenetic histories (Hiatt et al. 2010, Renac et al. 2002). However, uranium deposits within
the Kiggavik-Andrew Lake trend significantly differ from the unconformity-related uranium
deposits in the Athabasca basin by (1) the absence of graphite along the regional faults as well
as in the mineralized structures and (2) a lower average ore grade (around 0.5%).
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
52
Figure 1-1 : Kiggavik-Andrew Lake simplified geological map, showing deposit & prospects. Black dots for
sampled drillhole locations, simplified geology based on GSC Open file 1839, Schultz Lake GIS map.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
53
The aim of the present study is to determine the sequence of mineral crystallization
that occurred in the alteration halo associated with uranium mineralization along the
Kiggavik-Andrew Lake trend. Alteration petrology has been used to refine the spatial
distribution of the mineral assemblages and the chronological relationships between the
secondary mineral phases related to uranium mineralization. The mineralogical characteristics
of the alteration halo have been compared with those of the unconformity-related uranium
deposits of the Athabasca Basin in order to provide new insight on the genesis of uranium
mineralization at Kiggavik. Finally, crystal structure and crystal chemistry of clay minerals
and associated mineral phases have been investigated to identify new vectors to
mineralization at the prospect scale.
1.3. Geological setting
A simplified geological map of the Kiggavik-Andrew lake area is presented in Figure 1-1
(Hadlari et al. 2004). At a regional scale, the litho-structural pile consists of Mesoarchean
granitic, granodioritic and augen gneisses (2866±6 Ma; (Zaleski et al. 2001) tectonically
overlain by a Neoarchean metavolcano-sedimentary package retromorphosed to greenschist
facies. The latter consists in quartzo-feldspatic wackes and minor quartzite with thin
interbedded banded iron formation layers, rare black shales, and locally komatiite and
rhyolite. Geochronology on interbedded volcanics in the wacke give a U-Pb zircon age of
2710±2.1 Ma (Davis and Zaleski 1998). This Archean supracustal package, known as the
Woodburn Lake Group (WLG), belongs to a set of several greenstone belts due to continental
rifting of the Rae Province, which extends over 2000 km from northern Saskatchewan to the
North of Baffin Island (Hartlaub et al. 2004). Both Archean and the unconformably overlying
Early Paleoproterozoic Amer and Ketyet River Groups, underwent tectono-metamorphic
events during Middle Paleoproterozoic times (Hoffman 1990), due to the polyphased tectonic
accretion of the Laurentian Craton during Trans-Hudson (2.0-1.8 Ga) and Taltson-Thelon
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
54
orogens (2.0-1.9 Ga). Both the Woodburn and Amer-Ketyet Groups were intruded by Hudson
granite and syenite around 1.85-1.79 Ga and by Nueltin granite and associated Pitz rhyolite at
1.75 Ga (Peterson et al. 2002, Van Breemen et al. 2005). Following late Hudsonian
metamorphic events, dated at 1750 Ma in the northern Saskatchewan (Orrell et al. 1999), post
orogenic uplift and erosion generated large volumes of detrital material while regional
thermal and tectonic subsidence accommodated space for deposition of thick flat lying
siliciclastic sequences, forming the Dubwant Supergroup (Rainbird et al. 2003). This Late
Paleoproterozoic non metamorphic rock package comprises the Wharton and Baker Lake
Groups and the uncomformably overlying Barrensland Group which includes the Thelon
Formation sandstones (Rainbird et al. 2003). The siliciclastic sequences accumulated in
widespread intercontinental sag and fault controlled basins. Late thermal events of
Mesoproterozoic age are evidenced by the Kuungmi Formation basalts, of limited extent in
the central part of the Thelon basin, and by the McKenzie dyke swarms (Fahrig 1987).
At the regional and deposit scale uranium mineralization is typically hosted in the Woodburn
Group metagraywackes, in the vicinity of a N080 fault trend, preferably where second order
structures are present. Ore is located within a clay alteration halo centered on faults, itself
surrounded by a hematite pervasive alteration extending over tens of meters. Disseminated
mineralization can also be found in relatively weakly argillized or hematized rocks (e.g. End
deposit).
1.4. Sampling and analytical procedure
Sampling has been carried out extensively along the Kiggavik-Andrew Lake trend in various
basement lithologies to determine the regional alteration background and the specific clay
signature related to uranium ore deposits. A total of 217 samples (selected from 17 diamond
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
55
drillholes) were collected for detailed petrology and crystal-chemistry. Sampling has been
both focused on altered rocks in mineralized zones (i.e., Bong prospect, End deposit and
Andrew Lake deposit) and on poorly altered to fresh rocks from barren drill holes at various
distances laterally to the main structures controlling the mineralization. Such sampling allows
the lateral variation of mineral paragenesis from fresh rocks to strongly altered fault cores
with or without mineralization. The Bong prospect was chosen for its rock package of
homogeneous metasediments to minimize the influence of the protolith chemistry on the
mineral paragenesis.
Rock samples were gently crushed and put in deionized water to get mineral suspensions
afterwards dispersed ultrasonically during 2 minutes. Clay size fractions < 4µm were
extracted by sedimentation for oriented and randomly oriented powder mounts. No cation
exchange was performed. Chemical composition, morphology and texture of clay mineral
assemblage were studied using a JEOL® 5600 electron microscope equipped with a Bruker
energy dispersive X-ray spectroscopy detector (EDS). Analytical conditions were as follows:
accelerating voltage 15 kV, probe current 1 nA, working distance 17 mm, counting time of
100 s. The analyzed elements were Na, Mg, Al, Si, Mn, Fe, Ti, K, and Ca. The microanalysis
system was calibrated using synthetic and natural oxides and silicates (MnTiO3, hematite,
albite, orthoclase, and diopside) and corrections were made using a ZAF program. The
relative errors on the analyzed values are <1.5% (except Na which is >3%). Total Fe has been
arbitrarily considered as FeO or Fe2O3 according to the nature of the analysed mineral.
All clay preparations were analyzed on a Bruker D8 Advance diffractometer. Diffracted beam
CuKα1+2 radiation was used (40kV, 40mA) and collected by a linxeye detector. Relative
humidity was not controlled during data acquisition. Experimental conditions used for X-ray
diffraction (XRD) data collection are given in Table 1-1.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
56
Table 1-1 : Conditions used for X-ray diffraction data collection
Type of preparation Angular range
°βƟ Scanned range
(Å) Step size °βƟCuKα
Counting time (s)
Oriented slides 2-30 44.0-2.98 0.01 1
Clay separation: AD and EG1
Randomly oriented preparations 19-34 4.67-2.64 0.01 5
(polytypes determination)
Randomly oriented preparations 58-65 1.59-1.43 0.01 5 determination of the 060 reflection
1AD: Air dried, EG ethylene glycol solvated 2060 reflection is used to determine the b parameter and hence to distinguish the dioctahedral, di-
trioctahedral and triocataedral phyllosilicates
The crystallinity of illite along the c axis was estimated by measuring the full width at half
maximum intensity (FWHM) of the typical d001 reflection on oriented preparations.
Although more advanced methods have been developed recently (Drits et al., 1997, among
others), this broad method still remains suitable for illite (Guggenheim et al., 2002). Illite
polytypes were identified by XRD on clay separates that were randomly oriented using a
back-loading method as described and recommended by Moore and Reynolds (1989). The
diffraction patterns were recorded using the step-scanning mode from 19 to 34 °2(4.67-2.64
Å) with a step size of 0.01 °2 and a counting time of 5s per step. Illite polytype identification
was based on comparisons with reference data given in Bailey (1980) and (Brindley and
Brown 1980) for 1M and 2M1 polytypes and (Drits et al. 1993) for pure tv-1M (1M polytype
with trans-vacant octahedral cation occupancy) and cv-1M (1M polytype with cis-vacant
octahedral cation occupancy) polytypes. Note that earlier references used the terms “1M” and
“3T” for illite polytypes that are now considered to be tv-1M and cv-1M respectively (Drits et
al. 1993, Reynolds 1993), Table 1-2.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
57
Table 1-2 : X-ray diffraction lines characteristic of illite polytypes: tv-1M (octahedral trans vacant), cv-1M
(octahedral cis vacant) and 2M1 polytypes.
tv-1M cv-1M 2M1
Pos Å hkl Pos Å hkl Pos Å hkl Properties
3.655 1 12 3.591 112 Diagnostic peaks of of tv-1M and cv-1M polytypes
3.073 112 3.126 112 Diagnostic peaks of tv-1M and cv-1M polytypes
3.885 3.889 Common to 2M1 and 1Mc polytypes
2.875 2.870 115 Common to 2M1 and 1Mc polytypes
3.735 023 Specific to 2M1 polytype
3.500 114 Specific to 2M1 polytype
3.208 114 Specific to 2M1 polytype
2.999 025 Specific to 2M1 polytype
ArcGIS® and the Geosoft Target® module were used for Kriging interpolation and mapping
of the crystal properties of clay mineral in 2D & 3D with a 12*12*12 meters cell size.
1.5. Petrography and mineralogy
The lithology of fresh rocks and their altered and mineralized equivalents encompasses the
Woodburn Group metasediments, the underlying augen gneiss and highly silicified feldspar
bearing aphanitic rocks thought to be porphyritic rhyolite or mylonitized (micro)granite.
Locally, these rocks have been intruded by late mafic rich gabbro or biotite rich lamprophyre
to more differentiated, coarse to fine grained syenite, and quartz- K feldspar granite and
feldspar porphyry. The dominant ore bearing lithology are the Woodburn Group
metasediments in which alteration is the most widely developed. Macroscopically, fresh rocks
of the metasedimentary package are dark green and dominated by fine to medium grain meta-
arkose to wacke with rare lithic fragments. Pyrite rich pelitic horizons as well as thin layers of
banded iron formation (up to 10 cm thick) are interbedded. The metasediments consists of
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
58
feldspar (55 %), with dominant K-feldspar and quartz (40 %); accompanied by biotite, white
mica, minor garnet in places and accessory minerals such as tourmaline, zircon, rutile, pyrite
and magnetite. These metasediments were affected by a retrograde metamorphism
(greenschist facies) which consists of pervasive chloritization of biotite, sericitization of
feldspars and occurrence of minor veinlets filled by epidote, alkali feldspars and late
carbonates.
1.5.1. Alteration features
Macroscopically, hydrothermal alteration of the metamorphic basement resulted in color
change of the rocks in response to mineralogical transformation as well as transfer of
chemical elements, especially iron. Several contrasting features have been noted (Figure 1-2):
bleaching related to strong argillization (illitization and chloritization) and desilicification,
reddish coloration related to crystallization of iron oxide (mostly hematite), and late
silicification (secondary quartz). All these features are spatially related to faults from
millimeter to several meters wide fault zones, highlighting the strong structural control of the
alteration. Both fractures and alteration decrease in intensity from the fault core (Figure 1-
2a), to the damage zone and then to the distal surrounding rocks in which only diffuse
alteration is present (Figure 1-2b). The regional N070 fault trends, such as the Thelon and
Judge Sisson North Faults, are characterized by extensive hematization and silicification.
Protracted tectonic and hydrothermal activity is expressed by numerous phases of brecciation
and alteration that led to complex textures of hydraulic quartz breccia (Figure 1-2c)
frequently overprinted by late pervasive silicification, resulting in alternating bands of
hematized and silicified breccia. Strong argillization (bleaching) associated with various
degrees of desilicification occurs along the fault core and within the main mineralized zones.
Although the original foliation is still visible in most of the intensely altered rocks, the
lithology and structure of the protolith is difficult to identify. The thickness of the fault gouge
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
59
is generally limited to 10s of centimeters whilst the width of the whole mineralized structure
(gouge + damage zone and associated alteration halo) may reach several tens of meters. Fault
gouges are often superimposed on inherited structures such as quartz-carbonate veined
corridors resulting in mixed fragments of sub-angular argilized basement, quartz and
carbonates embedded in an illitic matrix. At greater lateral distance from the uranium deposits
and their associated altered zones, minor faults are expressed as tectonic brecciation corridors
in which the mechanical grinding (attrition) led to a chlorite-rich greenish fault gouge.
Usually, hematization is observed at the transition between the fault damage zone and
surrounding weakly altered basement rocks. These transition zones outlined by redox fronts
are frequently mineralized.
Figure 1-2 A : Totally argilized fault gouge at the footwall of mineralized zone, Bong-043 drillhole; B, Fresh
metagraywacke bleached over 50 cm by diffusive illitization around a centimeter microfault, Bong-045 drillhole.
C, Outcrop along the Sisson North Fault showing intense N080 quartz veining in a strongly hematized
A B
C D
Foliation plan
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
60
metagraywacke; D, Mineralized rock sample with pitchblende impregnation along the foliation plans Bong-042
drillhole around 400 m below erosion surface.
At the thin section scale, alteration is related to dissolution of preexisting metamorphic
silicates and to crystallization of an abundant clay matrix composed of illite associated with
variable amounts of sudoite (di-trioctahedral Al -Mg chlorite). Illitization occurs both as
pseudomorphic replacement of K-bearing metamorphic minerals (Figure 1-3a) and chlorite,
and as neoformation of fine grained (less than 10m) laths or whiskers in the secondary
porosity of the altered rocks. In altered intrusive rocks, the feldspars phenocrysts are totally
replaced by illite and specular hematite. Sudoite is intimately associated with illite, forming
millimetre size pockets of extremely fine grained flaky or lathy particles aggregates (Figure 1-
3b) or as partial replacement of exfoliated metamorphic phyllosilicates.
In addition iron remobilization from metamorphic phases (phyllosilicates and sulfides) is
shown by textural relashionships. The corrosion of iron bearing minerals is followed the
release of iron and precipitation of hematite in the secondary porosity (Figure 1-3c). Hematite
as well as barite grows after titanium oxides (Figure 1-3d).
Minor amounts of phosphate minerals are closely associated with illite and sudoite. They
consist of aluminum phosphate-sulfate minerals (APS) and apatite. APS minerals occur as
tiny euhedral crystals ranging in size from less than to 10 µm up to 50 µm, and frequently
display features of chemical zoning. Sr and S rich APS (svanbergite) dominate in the external
alteration halo, up to hundreds of meters away from the mineralized zones. With decreasing
distance from orebodies the general trend is a transition from svanbergite to LREE-rich
phosphate (florencite). Locally, The APS minerals can be fractured and partly dissolved with
smoothed edges. Secondary apatite occurs close to and within the mineralized zones. It is
textural association with pitchblende displays features of cogenetic growth, with inclusions of
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
61
pitchblende inside apatite or coatings of colloform pitchblende around apatite and titanium
oxides.
Figure 1-3 A : Hanging wall of the main mineralized structure with strong alteration and replacement of
metamophic 2M1 micas by laths of tv-1Millite (identified by XRD) showing an exfoliation texture; Bong-042;
B, Sudoite (S) pocket occurring in illitized phengite laths, Bong-008; C Metamorphic chlorite partially altered to
illite with associated crystallization of hematite, End09-11 ; D Illitization of metamorphic Fe-Mg
phyllosilictates leading to precipitation of titanium oxides, hematite spherules and minute crystals of barite in the
secondary porosity, End09-11.
Abbreviations; Brt: barite, Cal: calcite, Chl: chlorite, Coff: coffinite, Gn: galena, Hem: hematite, Ill: illite, Qtz:
quartz, TiO2: titanium oxide, Sud: sudoite, Uran: uraninite
Sud
A B
Ms
Ill
Ill
Ill
Hem Qtz
Brt
TiO2
Qtz
ChlFeMg ChlFeMg
Hem
Qtz C D
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
62
1.5.2. Ore paragenesis
Uranium mineralization is spatially related to the faults and their alteration haloes. At least
two generations of uranium mineralization have been found. The first consists of pitchblende
coatings on foliation planes and along fracture walls in weakly to strongly bleached host rock
(Figure 1-2d & 1-4a). In this type of primary ore, metamorphic chlorite is normally partially
altered to illite and sudoite and disseminated patches of pitchblende occur in the fault gouge.
Uraninite is epigenetic on iron magnesium chlorite as well as pyrite with boxwork textures
(Figures 1-4b, 1-4c & 1-4d). Uraninite is altered and replaced by coffinite in corrosion pits
latter filled with barite and galena. Pitchblende is also present as fracture filling and smearing
along microfaults planes with or without iron oxides as well as along redox fronts in the fault
damage zone. This last mineralization setting could be interpreted as secondary
remobilization of primary mineralization. Pitchblende does not appear to be associated with
iron oxides, and hematite staining frequently overprints argillized zones that are not
necessarily mineralized.
The primary ore paragenesis observed in thin section is uraninite later replaced by coffinite.
Metallic sulfides are rare, mainly as chalcopyrite and Cu, Co & Ni sulfides. They occur as
minute crystals and colloform products which are cogenetic to pitchblende and clay alteration
minerals. Subhedral to euhedral titanium oxides, apatite and APS disseminated in the clay
matrix often show partial dissolution features, and are frequently rimed by pitchblende
overgrowths. Apatite is particularly abundant within the mineralized zone.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
63
Figure 1-4 : A Mineralized rock sample of metasediments showing the pitchblende (colloform uraninite)
precipitation along the foliation plans in which the metamorphic phyllosilicates have been transformed to illite.
The intergranular voids are cemented by pitchblende, Bong-042 drillhole; B Metamorphic phyllosilicate
pseudomorphs and uraninite overgrowths, End09-04 drillhole; C Metamorphic phyllosilicate pseudomorphs and
uraninite overgrowths, postdated coffinite crystallization and calcite cementation, End09-04; D Pyrite and
uraninite (boxwork texture) subsequently altered in coffinite and cemented by late calcite, End09-04.
1.6. Textural properties and crystal structure of phyllosilicates
Two distinctive types of phyllosilicates have been identified on the basis of textural
characteristics. Metamorphic phyllosilicates in large subhexagonal plates ranging from 15 to
50 µm are oriented along foliation planes, whereas hydrothermal phyllosilicates replace all
the minerals of the basement rocks (including the micas) in zones of intense alteration and
consist of fine grained laths to flakey particles of < 5 µm.
A
S
Qtz
Uran
B
Uran
Brt
C
Uran Cal
Coff
Gn D
Coff
Uran
Pyrite
boxwork Cal
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
64
The XRD data of oriented and randomly oriented powders of the <4 m size fraction of all
samples investigated along the Kiggavik-Andrew Lake trend are dominated by dioctahedral
potassic phyllosilicates (micas and illite) associated with variable but generally small amounts
of chlorite (Figure 1-5). The crystal structure of phyllosilicates was investigated through the
full width at half maximum (FWHM) of the peaks corresponding to the d001 reflections
(close to 10 Å and 14 Å for illite and chlorite respectively) and through the relative amounts
of different polytypes identified from the randomly oriented powders mounts.
Figure 1-5 : X-ray diffraction patterns of oriented preparations of clay separates (< 4m) of representative
samples from the alteration halo surrounding the Bong deposit. (A) sample from the damaged zone, (B) sample
3 8 13 18 23 28
A
B
C
°2θ, Cu Kα
chl/sud chl/sud
chl/sud
chl/sud
Ill
Ill
Qtz
Ill
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
65
from the fault core hosting the mineralization; (C) sample from a sudoite-rich level. Ill: Illite, Sud/Chl: Sudoite
& Chlorite, Qtz : quartz diffraction peaks.
In fresh to very poorly altered basement rocks, the phyllosilicate assemblage of metamorphic
origin is made of dioctahedral micas (muscovite or phengite) and trioctahedral Fe-chlorite
with weak intensities of odd basal reflections compared to the even ones and d060 ranging
between 1.54 and 1.55Å). The d001 reflections of K-mica and chlorite are characterized by
very low FWHM (less than 0.1° 2) and the XRD patterns of mica has all the index hk
reflections of the 2M1 polytype (Figures 1-6 and Table 2).
Figure 1-6 : XRD diffraction patterns of randomly oriented mount of clay separates illustrating the change in
polytype of the dioctaedral phyllosilicates as a function of their distance from a mineralized structure in the
altered metagraywacke. The index XRD reflections of 2M1 (dotted lines), cv-1M (solid lines) and tv-1M (dashed
line) are from Drits and Tchoubar, (1990). A fault gouge hosting most of the mineralization, B fault damage
zone, C fresh metagraywacke. Note the presence of significant amounts of unaltered feldspar and quartz in the
less than 4 µm size fraction of the fresh metagraywacke. 1 hk reflections of K feldspar, 2 hk reflections of albite.
19 24 29 34
2
1 1
1 1
1
2
2
1Mt 1Mc
2M1
2M1/1Mc 2M1/1Mc
2M1
1Mc
1Mt
C
B
A
°2θ, CuKα
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
66
In basement rocks affected by hydrothermal alteration, the phyllosilicate assemblage is
largely dominated by illite associated with small amounts of chlorite. Compared to those of
the metamorphic phyllosilicates, the d00l reflections of both hydrothermal illite and chlorite
have distinctive peak profiles and intensity ratios (Figure 1-5). The d00l reflections of ill ite
and chlorite are broad (0.3<FWHM <0.65° 2and >0.15° 2, respectively). XRD patterns of
hydrothermal illite indicate a mixture of tv-1M and cv-1M polytype with a trend to
predominance of tv-1M polytype in the fault gouge that is totally illitized (Figure 1-6). In
addition, the XRD patterns of the hydrothermal chlorite are characteristic of the sudoite. They
differs from that of the trioctahedral chlorite by an intense d003 reflection compared to the
d001 reflection (Figure 1-5) and by a d060 spacing close to 1.51 Å (instead of 1.54 Å or
more for a trioctahedral chlorite) . Comparing the XRD patterns of all rocks samples, it
appears that the FWHM values of the dioctahedral K-phyllosilicates strongly increase and the
amount of 2M1 polytype decreases and then disappears with increasing hydrothermal
alteration (Figure 1-6). As 2M1 polytype and the lowest FWHM values are representative of
the metamorphic micas, such a trend can be a consequence of the alteration of metamorphic
micas and their replacement by illite as observed by SEM investigations (Figure 1-3a).
However, the FWHM values of the hydrothermal illite continue to increase with increasing
alteration, such that in the highly altered zones, no 2M1 micas persist. Increase in FWHM
values of the d00l reflection of illite is correlated with the increasing amount of tv-1M
polytype close to the uranium mineralization.
1.7. Phyllosilicate crystal chemistry
Microprobe analyses of metamorphic micas by EDS and the calculated structural formulas on
the basis of 11 oxygens per half formula unit are fairly homogeneous and are comparable to
muscovite with phengitic substitutions (Si+R2+ = Al IV+AlVI ). This is illustrated by (1) Si
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
67
contents higher than 3 atoms coupled with amounts of divalent atoms ranging from 3.04 to
3.29 (2) interlayer charges totally satisfied by K and ranging between 0.9 and 1 atom, and (3)
octahedral occupancies close to 2 atoms (Table 3a). The Fe/Fe+Mg ratios (XFe) of these
micas range between 0.6 and 0.8. The structural formula of hydrothermal illite (Table 3b)
differs from those of metamorphic micas by a higher Si content from 3.3 to 3.4 atoms coupled
with a lower interlayer charge ranging from 0.75 to 0.85 atom. Compared to metamorphic
micas (Figure 1-6), the composition of illite is very poor in Fe (<0.04 atom) and richer in Mg
(>0.20 atom). As a consequence, they can be easily distinguished by their very low Fe/Fe+Mg
ratios of < 0.1.
Chemical analyses and structural formulae of metamorphic chlorite indicate an iron-rich
species of trioctahedral chlorite (Table 1-3). Their octahedral occupancy is close to 6 atoms
when the structural formulae were calculated with total Fe in the ferrous state and their XFe is
generally higher than 0.5. The structural formulas of the hydrothermal chlorites are more
heterogeneous than those of the metamorphic chlorites. Most of them are comparable to those
of the sudoite (Table 1-3), which is the di-trioctahedral chlorite species identified by XRD
investigations. The structural formula of sudoite is characterized by an Al-Mg rich
composition and an octahedral occupancy close to 5 atoms. The fact that many analyses of
what was initially thought to be sudoite are in fact mixture of variable amounts of sudoite
with illite is indicative of the very small size of the crystals and their close association with
illite even at a few micrometers scale. Chemical analysis of hydrothermal chlorites has also
permit to identify Mg-rich trioctahedral chlorites in a few altered samples (Table 1-3). These
chlorites sealed late microfractures in some hydrothermally altered samples. The chemical
composition of this Mg-rich chlorite is typical of the clinochlore species. It is characterized by
low iron content (XFe<0.10) and a trioctahedral structure with the presence of a small
amount of octahedral vacancy (octahedral occupancy averaging 5.75 atoms).
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
68
Table 1-3 : EDS analysis and structural formulas of representative phyllosilicates in the Kiggavik- Andrew Lake
trend
1 2 3 4 5 6 7 8 SiO2 24.01 31.59 33.86 43.96 45.45 42.33 43.00 48.38 TiO2 0.05 0.01 0.06 0.56 0.36 0.34 0.00 0.04 Al 2O3 19.32 15.58 28.78 31.44 33.38 29.35 27.61 27.78 FeO 27.17 4.39 0.20 2.11 2.31 4.28 Fe2O3 0.04 0.45 MnO 0.22 0.00 0.00 0.00 0.10 0.06 0.00 0.03 MgO 11.90 28.33 17.26 1.46 1.32 1.48 1.80 2.63 CaO 0.03 0.19 0.07 0.00 0.03 0.00 0.06 0.14 Na2O 0.26 0.36 0.32 0.39 0.49 0.44 0.21 0.27 K2O 0.03 0.00 0.22 10.23 10.37 10.03 8.60 8.14 Total 83.00 80.45 80.77 90.15 93.83 88.32 81.33 87.85 Si 2.73 3.22 3.27 3.12 3.09 3.11 3.30 3.42 Al IV 1.27 0.78 0.73 0.88 0.91 0.89 0.7 0.58 AlVI 1.32 1.09 2.54 1.74 1.77 1.65 1.80 1.73 Ti 0.00 0.00 0.00 0.03 0.02 0.02 0.00 0.00 Fe 2.58 0.37 0.02 0.12 0.13 0.26 0.00 0.02 Mn 0.02 0.00 0.00 0.00 0.01 0.00 0.00 0.00 Mg 2.02 4.31 2.48 0.15 0.13 0.16 0.21 0.28 Occ 5.94 5.78 5.04 2.05 2.06 2.10 2.01 2.03 XFe 0.56 0.08 0.01 0.45 0.50 0.62 0.01 0.08 Ca 0.00 0.02 0.01 0.00 0.00 0.00 0.00 0.01 Na 0.06 0.07 0.06 0.05 0.06 0.06 0.03 0.04 K 0.00 0.00 0.03 0.93 0.90 0.94 0.84 0.73 Int. Ch. 0.07 0.11 0.10 0.98 0.97 1.00 0.88 0.79
1 Metamorphic chlorites; 2 Hydrothermal clinochlore associated with a dolomite veinlet; 3 Sudoite filling
veinlet; 4-5 Metamorphic micas; 6 Relics of metamorphic micas persisting in a mineralized zone; 7 illite pocket
in a fault gouge; 8 illite in a mineralized zone. Xfe:(Fe/Fe+Mg), Int. Ch : Interlayer Charge, Total: sum of the
oxide Wt%. The fact that the total oxide Wt% of hydrothermal illite and chlorite are slightly lower than expected
for theoretical ones (>90% and 86% respectively) can be explained by the microporosity of the clay material.
Such a deviation did not affect the calculation of the structural formulas.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
69
1.8. Discussion
1.8.1. Comparing the alteration pattern of the Kiggavik-Andrew Lake trend
to those of unconformity-related uranium deposits in the Athabasca
or the Kombolgie Basins.
The alteration pattern associated with the uranium deposits of the Kiggavik-Andrew Lake
trend shows a great number of similarities with those of basement hosted unconformity-
related uranium deposits described in both the Athabasca Basin (Cloutier et al. 2009,
Jefferson et al. 2007) and references therein) or the Kombolgie Basin (Beaufort et al. 2005,
Gustafson and Curtis 1983) and references therein). Such similarities include the geometric
shape of the alteration halo as well as the sequence of mineral crystallization and the
mineralogical characteristics of the secondary minerals. They can be summarized as follows:
(1) Similar alteration halos in fracture controlled uranium mineralization in clay-rich rocks
associated with dissolution of silicates and quartz in retro-metamorphosed basement rocks.
(2) Similar crystal chemistry of the secondary mineral phases dominated by illite and both di-
trioctahedral (sudoite) and trioctahedral chlorites with minor amounts of phosphate minerals
(APS, apatite) and hematite.
(3) Similar time-space alteration sequence expressed by zoned alteration around the fracture
network which hosts the uranium mineralization: i.e. illite ± sudoite followed by late
clinochlore in veinlets and lateral transition from APS to apatite toward the mineralized zone.
The occurrences of unconformity-related uranium deposits in Canada and Australia are
usually interpreted on the basis of the widely accepted diagenetic-hydrothermal genetic model
originally proposed by (Hoeve and Quirt 1984, Hoeve et al. 1980). According to this model
and all the refinements proposed thereafter, the uranium ores formed close to the
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
70
unconformity are the result of a long period of tectonically controlled interaction between
diagenetic oxidizing basinal brines at the base of deep continental basins and hydrothermal
reducing fluids circulating in basement faults (Jefferson et al. 2007, Kyser and Cuney 2008).
The spatial distribution of the alteration haloes associated with unconformity uranium
mineralization in the Athabasca Basin show contrasting patterns interpreted as representative
of discharge (“egress” style) and recharge (“ingress” style) zones (Quirt 1989, 2003). Egress
style is characterized by extensive and zoned alteration pattern in the sub-basinal sandstones
in response to upward fluid flow from basement-rooted faults. Ingress style shows more
limited inverted alteration haloes, mainly within the faulted basement, in response to
downward infiltration of basinal fluids in probable extensional local settings.
From the aforementioned considerations, the alteration pattern associated with the uranium
deposits along the Kiggavik-Andrew Lake area have many of the characteristics associated
with basement hosted unconformity-related uranium deposits. This suggests a close
relationship between the genesis of these ore deposits and both the burial history and tectonic
evolution of the Thelon Basin which has a potential for hidden uranium deposits (Beyer et al.
2011, Miller and LeCheminant 1985, Rainbird et al. 2003). However, compared to the
basement-hosted uranium deposits of the Athabasca Basin such as Shea Creek (Laverret et al.
2006) or Millenium (Cloutier et al. 2009), the alteration pattern associated with the uranium
deposits of the Kiggavik-Andrew Lake differs by the absence of significant amounts of
graphite in the fault system and the absence of dravite in the paragenetic sequence.
1.8.2. Crystal structure of clay minerals as a vector to mineralization in the
Bong prospect
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
71
Several authors have shown that the crystal structure of phyllosilicates can be used as a vector
to mineralization in the unconformity-related uranium deposits of Australia and Canada
(Beaufort et al. 2005, Laverret et al. 2006). As the full width at half maximum (FWHM) of
phyllosilicates depends on the degree of order-disorder in the layer staking sequence, the d001
XRD reflections of illite or chlorite are broad indicators of P-T conditions in geological
environments (see reviews and critical comments in (Guggenheim et al. 2002). The FWHM
of the d001 reflection of metamorphic white micas (FWHM< 0.10 °βθ) is lower than those of
the hydrothermal illite (0.15 °βθ <FWHM< 0.70 °βθ), and the FWHM values of illite tend to
increase as a function of decreasing distance to the uranium mineralisation (Figure 1-7).
The FWHM values of the d001 reflection of illite have been systematically measured to map
their variation around the Bong deposit.
Figure 1-7 : Change in peak profile of the d001 reflection of the K-bearing dioctahedral phyllosilicates according
to their distance to the uranium mineralization. The FWHM of the peak gradually increases from less than 0.10
8 8.5 9 °2θ, CuKα
I
A
B
C
D
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
72
°2θ to more than 0.70 °2θ from the unaltered metagraywakes until the mineralized fault core. A, fresh
metagraywacke, B fault damaged zone, C barren fault core, D mineralized fault core.
1.8.2.1. MAPPING THE FWMH OF THE ILLITE/MICA D001 REFLECTION
The extensive dataset of FWHM values obtained from samples from the Bong prospect are
distributed in four categories arbitrarily based on the crystallographic data and the intensity of
clay alteration (Figure 1-8). These ranges corresponds to (1) fresh rocks containing only
metamorphic micas (FWHM< 0.10 βθ), (2) very weakly illitiz ed rocks (FWHM< 0.15 βθ) that
are “fresh” macroscopically; (3) moderately to strongly illitized rocks (FWHM< 0.30 βθ)
which are sill cohesive with a weak to moderate desilicification and that show a typical
mixture of 2M1 and 1M polytypes in the damage and distal alteration zones around the
structure; and (4) totally illitized rocks (FWHM > 0.30 βθ) in which illite is the only potassic
phyllosilicate in the strongly desilicified metasediments and the fault gouges.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
73
Figure 1-8 : Interpolation of FWHM values of the d001 XRD reflection of illite/micas using Kreiging method
permits to ouline a zoned distribution of the average crystallinity along the c axis of these minerals around the
uranium orebodies of the Bong prospect. The edge of the mineralized halo in the section is indicated by the black
dotted line.
The spatial populations of samples (in average a point every 10 m in the Z direction and every
20 m on the XY plan) allow to use interpolation tools, in this case Kriging method, to map the
intensity of the alteration related to the mineralization process on the basis of the d001
FWHM of the potassic phyllosilicates. The result of such interpolation methods allows to map
the intensity of the alteration process and to outline the geometry of the hydrothermal haloes
at larger scale (Figure 1-8). Knowing the position of the main structure in the Bong prospect,
this alteration map confirms the location of the uranium orebodies inside the more strongly
illitized part of the alteration halo. Such maps could be also very useful for further
assessment of the altered rock volume around the structures. As a general statement, illite
with the highest FWHM values are closely related to the fault gouge and more specifically to
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
74
the mineralized zones. Micas with low FWHM values have been found in fresh rocks as well
as in the damage zone where the dioctaedral micas have been only partially transformed
during the alteration processes.
1.8.2.2. MAPPING THE DISTRIBUTION OF SUDOITE
Sudoite occurs proximal to the uranium orebodies in most unconformity-related uranium
deposits (Quirt 1989, 2003). The spatial distribution of this mineral has been mapped in the
alteration halo of the Bong prospect (Figure 1-9).
Figure 1-9: Interpolation of the chlorite-sudoite relative proportions estimated from the diffraction peakratio (
Kcs factor) with a Kreiging method permitting to map the spatial distribution of sudoite in the alteration halo of
the Bong prospect. The edge of the mineralized halo in the section is indicated by the black dotted line.
The relative amount of sudoite in the bulk chlorite material has been estimated based on the
intensity ratio between the d003 and d001 reflections of the chlorite minerals (corresponding
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
75
to d spacing close to 14Å and 4.75Å respectively) measured after background stripping in the
XRD pattern of oriented clay preparations (referred to Kcs factor hereafter). Trioctahedral
chlorite largely predominates if the Kcs factor is <1, both trioctahedral chlorite and sudoite
are mixed in equal proportions if the Kcs factor is close to 1, and sudoite largely predominates
over trioctahedral chlorite if the Kcs factor >1. It should be mentioned that this method is only
a broad approximation of the amount of sudoite in the altered rocks. A more accurate
quantification could be done using quantitative XRD methods such as decomposition of X-ray
diffraction profile or Rietveld method. However such methods are time consuming and not
really appropriate to the analysis of a great number of heterogeneous samples. The good
correlation that is noted between the obtained Kcs factor and the petrographic observations
give confidence that this parameter highlights the major contrasts in alteration mineralogy.
Nevertheless, the confidence in this factor for mapping hydrothermal alteration has been also
checked on the basis of other structural parameters such as the b parameter of the chlorite
lattice cell (expected from the d 060 reflection of chlorite minerals) and the estimation of
mineral proportions from chemical analysis on clay separates.
Mapping the spatial distribution of sudoite in the Bong prospect shows that this mineral is
present throughout the alteration zone around the main structure where iron rich chlorite tends
to disappear. Thus, sudoite-rich zones are not strictly associated with the mineralization. At a
larger scale it seems distributed along two distinctive structures. The first one, relatively poor
in sudoite, is associated with the mineralization while the other one which occurs above is
richer in sudoite but contains only trace to weak amounts of uranium mineralization.
1.8.3. Relationships between clay alteration and hematization.
The crystal chemistry of phyllosilicates and the chemiographic representation of both the
metamorphic and hydrothermal assemblages in a MR3-2R3-3R2 diagram (Velde 1977, 1985)
outline a close relationship between clay alteration and hematization within the alteration
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
76
halos (figure 1-10). Dissolution of iron-rich phyllosilicates such as Fe-Mg trioctahedral
chlorite (XFe<0.5) and phengitic micas (0.6<XFe<0.8) and their replacement by illite
(XFe<0.1) and sudoite (XFe<0.02) is a geochemical evidence for a leaching of iron from the
silicate minerals during the hydrothermal process. Such a leaching can be explained by the
oxidation of ferrous iron during the dissolution of metamorphic minerals (silicates, Fe-Ti
oxides and sulfides) by the oxidizing and acidic basinal brines infiltrated along the fracture
network in the basement rocks. As incorporation of ferric iron in phyllosilicates such as
chlorite, di-tri or trioctahedral, is very limited (Billault et al. 2002, Nelson and Guggenheim
1993), most of the ferric iron precipited as cogenetic hematite. Moreover, as ferric iron
mobility is generally very limited due to its very low solubility in hydrothermal solutions, the
iron redistribution is centered on the structures where alteration took place.
Observations on the hydrothermal clay assemblage chemistry as well as the textural evidences
of hematite precipitation in the secondary porosity developed with alteration lead to the
conclusion that hydrothermal hematization was effective along the Kiggavik-Andrew lake
fault trend. Even if this does not mean that all the hematite observed at regional scale is a by-
product of the hydrothermal alteration process, we suggest that the hematite haloes observed
at the field scale are probably good indicators of proximal hydrothermal alteration zones.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
77
Figure 1-10 : Chemiographic representation of the phyllosilicate assemblages formed during both retrograde
metamorphic (■) and hydrothermal (◊) stages which successively affected the metasediments hosting uranium
mineralization. Structural formulas of phyllosilicates have been plotted in a MR3-2R3-3R2 diagram (Velde 1977)
in which MR3 represent feldspar compositions (Na+, K+, 2Ca2+ + Al3+) in atomic proportions, 2R3 represents the
dioctahedral pole [1/2 (Fe3+ + Al3+ + Ti4+)-MR3] and 3R2 represents the trioctahedral pole [1/2 (Fe2+ + Mg2+ +
Mn2+)]. The microprobe analyses which fall between the compositional fields of the phyllosilicates phases
labeled in the triangle correspond to two-phases (and more rarely three phases) admixtures.
1.9. Concluding remarks
This study indicates that most of the secondary minerals found within the alteration haloes
associated with uranium mineralization along the Kiggavik-Andrew Lake fault trend are
similar to those produced by diagenetic-hydrothermal alteration in basement hosted
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
78
unconformity-related uranium deposits (Figure 1-11). Only minor occurrences of propylitic
alteration expressed as epidote and feldspar veinlets give credit to the possible link invoked
between intrusive granitic bodies and a possible early stage of uranium mineralization in the
Kiggavik deposit (Weyer et al. 1987). Nevertheless the extent of such alteration is too limited
to be considered as representative of a major mineralizing event at regional scale.
Figure 1-11: Paragenetic sequence in the Kiggavik-Andrew Lake trend.
Diagenetic-hydrothermal alteration associated with uranium mineralization in the Kiggavik
Andrew Lake trend involves fluids originating from the Late Paleoproterozoic Thelon Basin.
Due to the present level of erosion, only basement hosted mineralization can be found in the
study area and the thickness of basement rocks which has been eroded since the formation of
the ore deposits is unknown. However both alteration and mineralization studied along the
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
79
Kiggavik Andrew Lake trend are related to steep structures and can be compared to the
basement hosted uranium deposits like Jabiluka in Australia or Shea Creek in the Western
Athabasca Basin of Canada in which mineralization and alteration follow corridors down to
several hundred meters below the unconformity. Nevertheless, contrarily to the Athabasca
basement, basement uranium mineralization in the Thelon Basin area is dominantly hosted by
coarse Late Archean metasediments along faults without graphite. The source of uranium
within the Kiggavik Andrew Lake trend is still conjectural but the very low uranium content
in unaltered metasediments and the evidence of interaction between diagenetic fluids and
basement rocks argue for a potential contribution of uranium from the Thelon Basin or for
mobilization of uranium from fertile basement rock at distance from the structural trend.
A few implications for uranium exploration can be deduced from the findings of this study.
The Kiggavik Andrew Lake trend is interpreted as the deep roots of an unconformity related
uranium deposit system, so the possibility of discovering uranium deposits closer to the
unconformity below the Thelon Basin at appropriate structural locations cannot be discarded.
Perhaps the findings on the mineralogical indicators developed in this study of would permit
to delineate new prospective uranium bearing alteration systems.
Acknowledgment
The authors would like to thank AREVA Mines for financial and technical support of this
study. The authors would like to thanks the reviewers, Pr Kyser and Pr Pagel for their detailed
comments which greatly helped to improve the manuscript.
1.10. References
BEAUFORT, D., PATRIER, P., LAVERRET, E., BRUNETON, P. and MONDY, J. (2005): Clay Alteration Associated with Proterozoic Unconformity-Type Uranium Deposits
in the East Alligator Rivers Uranium Field, Northern Territory, Australia. Economic Geology. v. 100, pp. 515–536.
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
80
BEYER, S.R., HIATT, E.E., KYSER, K., DALRYMPLE, R.W. and PETTMAN, C. (2011): Hydrogeology, sequence stratigraphy and diagenesis in the Paleoproterozoic western Thelon Basin: Influences on unconformity-related uranium mineralization. Precambrian Research. 187, 293-312. BILLAULT, V., BEAUFORT, D., PATRIER, P. and PETIT, S. (2002): Crystal chemistry of Fe-sudoites rom uranium deposits in the Athabasca basin ( Saskatchewan, Canada). Clays and Clay Minerals. 50, 69-80. BRINDLEY, G.W. and BROWN, G. (1980): Crystal structures of clay minerals and their X-ray identification, Mineralogical Society, London, UK CLOUTIER, J., KYSER, K., OLIVO, G.R., ALEXANDRE, P. and HALABURDA, J. (2009): The Millennium Uranium Deposit, Athabasca Basin, Saskatchewan, Canada: An Atypical Basement-Hosted Unconformity-Related Uranium Deposit. Economic Geology. 104, 815-840. DAVIS, W.J. and ZALESKI, E. (1998): Geochronological investigations of the Woodburn Lake group, western Churchill Province: preliminary results. Current Research 1998-F, Geological Survey Of Canada DRITS, V.A., WEBER, F., SALYN, A.L. and TSIPURKY, S.I. (1993): X-ray identification of one-layer illite varieties: application to the study of illites around uranium deposits of Canda. Clays and Clay Minerals. 41, 389-398. FAHRIG, W.F. (1987): The tectonic settings of continental mafic dyke swarms: Failed arm and early passive margin In Mafic dyke swarms. 34, Geological Association of Canada Special Paper FARKAS, A. (1984): Mineralogy and host rock alteration of the Lone Gull deposit. Internal report, Urangesellschaft FUCHS, H.D., HILGER, W. and PROSSER, E. (1986): Geology and exploration history of the Lone Gull property. Uranium Deposits of Canada, CIM Special Volume 33 GUGGENHEIM, S., BAIN, D.C., BERGAYA, F., BRIGATTI, M.F., DRITS, V.A., EBERL, D.D., FORMOSO, M.L.L., GALAN, E., MERRIMAN, R.J., PEACOR, D.R., STANJEK, H. and TAKASHI, W. (2002): Report of the association internationale pour l'étude des argiles(AIPEA) nomenclature committee for 2011: Order, disorder and crystallinity in phyllosilicates and the use of the "crystallinity index". Clays and Clay Minerals. 50, 406-409. GUSTAFSON, L.B. and CURTIS, L.W. (1983): Post-Kombolgie metasomatism at Jabiluka, Northern Territory, Australia, and it's significance in the formation of high grade uranium mineralization in Lowar Proterozoic rocks. Economic Geology. 78, 26-56. HADLARI, T., RAINBIRD, R.H. and PEHRSSON, S.:(2004) Geology Schultz Lake, Nunavut, open file 1839, scale 1: 250 000. Geological Survey Of Canada. HARTLAUB, R.P., HEAMAN, L.M., ASHTON, K.E. and CHACKO, T. (2004): The Archean Murmac Bay Group: evidence for a giant Archean rift in the Rae Province, Canada. Precambrian Research. 131, 345-372. HASEGAWA, K., DAVIDSON, G.I., WOLLENBERG, P. and YOSHIMASA, I. (1990): Geophysical exploration for unconformity-related uranium deposits in the northeastern part of the Thelon Basin, Northwest Territories, Canada. Mining Geology. 40, 83-95. HIATT, E.E., PALMER, S., E., KYSER, K. and O'CONNOR, T. (2010): Basin evolution, diagenesis and uranium mineralization in the Paleoproterozoic Thelon Basin, Nunavut, Canada. Basin Research. 22, 302-323. HOEVE, J. and QUIRT, D. (1984): Mineralization and host rock alteration in relation to clay mineral diagenesis and evolution of the Middle-Proterozoic Athabasca basin, Northern Saskatchewan, Canada. Saskatchewan Research Concil Technical report, Saskatchewan Reasearch Council
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
81
HOEVE, J., SIBBALD, T.I.I., RAMAEKERS, P. and LEWRY, J.F. (1980): Athabasca basin unconformity-type uranium deposits : a special class of sandstone-type deposits? In Uranium in the Pine Creek Geosyncline. International Atomic Energy Agency HOFFMAN, P.F. (1990): Subdivision of the Churchill Province and extent of the Trans-Hudson orogen In The Early Proterozoic Trans-Hudson Orogen of North Amercia. 37, Geological Survey of Canada Special Paper JEFFERSON, C.W., THOMAS, D.J., GANDHI, S.S., RAMAEKERS, P., DELANEY, G., BRISBIN, D., CUTTS, C., PORTELLA, P. and OLSON, R.A. (2007): Unconformity-associeted uranium deposits of the Athabasca Basin, Saskatchewan and Alberta In EXTECH IV . Geology and Unranium EXploration TECHnology of the Proterozoic Athabasca Basin, Saskatchewan and Alberta, Geological Survey of Canada, Bulletin 588, KYSER, K. and CUNEY, M. (2008): Unconformity-related uranium deposits In Recent and not so recent developments in uranium deposits and implications for exploration. Short Course 39, Mineralogical Association of Canada LAVERRET, E., PATRIER, P., BEAUFORT, D., KISTER, P., QUIRT, D., BRUNETON, P. and CLAUER, N. (2006): Mineralogy and geochemistry of the host-rock alterations associated with the Shea Creek unconformity-type uranium deposits (Athabasca basin, Saskatchewan, Canada) Part1. Spatial variation of illite properties. Clays and Clay Minerals. 54, 275-294. MILLER, A.R., CUMMING, G.L. and KRSTIC, D. (1989): U-Pb, Pb-Pb, and K-Ar isotopic study and petrography of uraniferous phosphate-bearing rocks in the Thelon Formation, Dubawnt Group, Northwest Territories, Canada. Canadian Journal of Earth Sciences. 26, 867-880. MILLER, A.R. and LECHEMINANT, A.N. (1985): Geology and uranium metallogeny of Proterozoic supracrustal successions, central District of Keewatin, N.W.T with comparisons to northern Saskatchewan. NELSON, D.O. and GUGGENHEIM, S. (1993): Inferred limitations to the oxidation of Fe in chlorite : a high-temperature single-crystal X-ray study. American Mineralogist. 78, pp. 1197-1207. ORRELL, S.E., BICKFORD, M.E. and LEWRY, J.F. (1999): Crustal evolution and age of thermotectonic reworking in the western hinterland of the Trans-Hudson Orogen, northern Saskatchewan. Precambrian Research. 95, 187-223. PETERSON, T.D., VAN BREEMEN, O., SANDEMAN, H. and COUSENS, B. (2002): Proterozoic (1.85-1.75 Ga) igneous suites of the Western Churchill Province: granitoid and ultrapotassic magmatism in a reworked Archean hinterland. Precambrian Research. 119, 73-100. QUIRT, D. (1989): Host rock alteration at Eagle Point South. R-855-1E-89, Saskatchewan Research Council QUIRT, D. (2003): Athabasca unconformity type uranium deposits: one deposit type with many variations. . Uranium Geochemistry International Conference, Nancy, France RAINBIRD, R.H., HADLARI, T., ASPLER, L.B., DONALDSON, J.A., LECHEMINANT, A.N. and PETERSON, T.D. (2003): Sequence stratigraphy and evolution of the Paleoproterozoic intracontinental Baker Lake and Thelon basins, western Churchill Province, Nunavut, Canada. Precambrian Research. 125, 21-53. RENAC, C., KYSER, K., DUROCHER, K., DREAVER, G. and O'CONNOR, T. (2002): Comparison of diagenetic fluids in the Proterozoic Thelon and Athabsca Basins, Canada: implications for protracted fluid histories in stable intracratonic basins. Can. J. Earth Sci. 39, 113-132. REYNOLDS, R.C. (1993): Three-dimentional X-ray powder diffraction form disordered illite: Simulation and interprétation of the diffraction patterns. LECTURES
Alteration related to uranium deposits in the Kiggavik-Andrew lake structural trend, Nunavut, Canada; new insights from petrography and clay mineralogy
82
VAN BREEMEN, O., PETERSON, T.D. and SANDEMAN, H. (2005): U-Pb zircon geochronology and Nd isotops geochemistry of Proterozoic granitoids in the western Churchill Province: intrusive age pattern and Archean source domains. Canadian Journal of Earth Sciences. 42, 339-377. VELDE, B. (1977): Proposed Phase-Diagram For Illite, Expending Chlorite, Corrensite and Illite-Montmorillonite Mixed Layered Minerals. Clays and Clay Minerals. 25, 264.270. VELDE, B. (1985): Clay minerals: A physico-chemical explanation of their occurence. Developments in Sedimentology, Elsevier WEYER, H.-J., FRIEDRICH, G., BECHTEL, A. and BALLHORN, R.K. (1987): The Lone Gull uranium deposit-New geochemical and petrological data as evidence for the nature of the ore bearing solutions. Metallogenesis of uranium deposits, 542/19, Proceedings of a technical committee meeting, Vienna ZALESKI, E., DAVIS, W.J. and SANDEMAN, H. (2001): Continental rifting, mantle magmas and basement/cover relashionships. 4th International Archean Symposium, Perth, Australia
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
83
2. Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
2.1. Introduction
Les nombreuses études d’inclusions fluides menées sur les gisements de type discordance
associés au basin de l’Athabasca sont venues étayer les modèles de minéralisations de type
diagénétique-hydrothermal dans lesquels des saumures oxydantes de bassin viennent interagir
avec des fluides et/ou des lithologies réductrices du socle (Pagel 1975, Pagel et Jaffrezic,
1977, Kotzer & Kyser, 1995, Derome et al, 2005, Hoeve & Quirt, 1984).
Une seule étude, limitée à des échantillons d’Andrew Lake a été réalisée sur les cristaux de
quartz associés aux gisements du faisceau de Kiggavik (Pagel et Ahamdach, 1995). Elle a mis
en évidence à la fois la circulation de fluides du bassin dans les roches du socle ainsi qu’une
histoire hydrothermale complexe plus précoce associée à des fluides de plus haute
température.
La présente étude vient donc compléter ces observations en étendant les investigations au
inclusions fluides présentes dans les cristaux de quartz et de dolomites associées au gisement
d’End Grid et Andrew Lake, et aussi au prospect de Bong. Deux échantillons provenant du
gisement d’End Grid seront étudiés. End09-05_13 à 254.9 m dans une veine de dolomite
massive et End09-07_06 à 210.0m dans une brèche hydraulique à remplissage de quartz
laiteux.
2.2. Bong
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
84
Les brèches hydrauliques à quartz et/ou carbonates sont relativement peu abondantes à
l’échelle de la zone de Bong. Elles sont sont cependant bien représentée dans le sondage
Bong33 situé au NE de la zone explorée. La structure portant la minéralisation a un pendage
vers le WSW. L’échantillon Bong39_04 64.8m est constitué par une veine à quartz et
carbonate de couleur miel clair à rosâtre montrant un jeu normal apparent reactivant
partiellement une microfracture cimentée par de la chlorite, dans un metagraywack très
faiblement altéré, Figure 2-1.
Figure 2-1 : Echantilllon BG39_04 présentant une microfaille à remplissage de quartz et carbonates avec
mouvement normal apparent et traces d’illitisation le long des épontes de la veinule, carotte diamètre NQ. Le
haut de l’image est dirigé vers le haut du sondage
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
85
2.3. End Grid
2.3.1. Echantillon : End09-05_13 @ 254.9m
Cet échantillon représente une veine de dolomite massive de 60 cm de puissance apparente et
encaissée dans un metagraywacke fortement argilisé au mur d’une zone de faille
plurimétrique.
Les 4 types d’inclusions identifiés dans les échantillons sont :
(1) Des inclusions triphasées constituées d’un liquide, d’une bulle de vapeur (estimée à environ 1% du volume de l’inclusion) et d’un cube de sel (L+V+H). Certaines de ces inclusions présentent également des inclusions solides sous forme de lamelles de nature indéterminée (illite ?).
(2) Des inclusions L+V (1 à10%) dans lesquelles ont observe parfois le mouvement de la bulle de gaz à température ambiante
(3) Des inclusions L+V (80%) (4) Des inclusions monophasées L
Les inclusions triphasées sont de loin les plus nombreuses. Elles sont de grande taille de 20
jusqu'à 50x150 µm et suivent généralement les plans de clivage du cristal de dolomite, figure
2-2.
Les inclusions biphasées présentent une grande hétérogénéité de taille et de morphologie,
certaines sont semblables au type (1) et tandis que d’autres en général de dimension
micrométriques et oblongues se répartissent sous forme d’alignements typiques de fractures
cicatrisées.
Les inclusions de types 3 et 4 sont elles aussi fréquement associées à des fractures secondaires
cicatrisées. Le necking down des inclusions n’étant pas un phénomène isolé il est fort
probable que de nombreuses inclusions des types β, 3, 4 résultent de la striction d’inclusions
triphasées de plus grande taille.
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
86
Seules les inclusions triphasées L+ V + H et les L + V à petites bulle de vapeur ont été
mesurées.
Figure 2-2 : Microphotographie des inclusions triphasées (L+ V + H) de grande taille dans la dolomite. De
l'échantillon End09-05_13
Les données microthermométriques montrent des températures d’homogénéisation figure 2-3
ainsi que des températures de fusion de la halite (TfNaCl) figure 2-4 très homogènes quelles
que soient la taille et la morphologie des inclusions considérées.
100 µm
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
87
Figure 2-3 : Histogramme de fréquence des températures d'homogénéisation (en °C) dans l'échantillon End09-
05_13
Figure 2-4 : Temperature de fusion de la glace en fonction des temperatures d'homogénisation, séparation des
inclusions triphasées des carbonates et de quartz
0
1
2
3
4
5
6
7
8
152 154 156 158 160 162 164 166 168 170 172 174 176 178 180 182 184 186 188 190
fré
qu
en
ce
Th en °C
Th Dolomite
70.00
90.00
110.00
130.00
150.00
170.00
190.00
70.00 90.00 110.00 130.00 150.00 170.00 190.00 210.00 230.00
Th
Tfglace °C
carbonates
quartz
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
88
Les températures de fusion de la glace sont plus homogènes parmis les inclusions triphasées
des cristaux de dolomite tandis que celles mesurées dans les quartz sont relativement
dispersées. De ce fait, il apparaît que certaines inclusions triphasées dans les quartz sont
situées sur des plans de fractures cicatrisées ce qui implique de possible réovertures ou des
piégeages à des instants différents. Au contraire dans les carbonates, les inclusions
apparaissent toutes primaires ou pseudo-primaires. Ainsi soit les carbonates ont piégé un seul
événement ce qui paraît peu probable ou bien les inclusions sont toutes secondaires et
marquent un seul et même événement de réactivation qui a conduit au remplissage des cavités
néoformées avec les saumures de fond de bassin. Cette réactivation est d’autant plus aisée que
les carbonates sont facilement clivables.
La seule température de fusion de la glace mesurée est extrêmement basse à -35.0°C, figure
2-5 et donne des salinités calculées de 14.7 wt% NaCl et 18.9 wt% CaCl2 en utilisant
l’équation de Steele-MacInnis, M., Bodnar, R.J. and Naden, J. (2010). A cette exception près
aucune prise de glace n’a été observée dans les inclusions triphasées malgré un
refroidissement jusqu’à -196°C.
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
89
Figure 2-5 : Température de fusion de la glace des inclusions triphasées dans la dolomite et biphasées le quartz
2.3.2. Echantillon : End09-07_06 @ 210.0m
Cet échantillon provient d’une brèche hydraulique à remplissage de quartz mise en place dans
un métagraywacke frais. Il se caractérise par une très forte densité d’inclusions fluides qui
rend difficile l’identification des différentes générations d’inclusions.
Les inclusions sont de petites taille avec des diamètres <20 microns. Elles se répartissent dans
la masse de quartz (sans organisation spatiale particulière) et le long de plans entre deux
phases de croissance de quartz ou des fractures cicatrisées.
4 types d’inclusions ont été identifés :
(1) L+V (1-5 %) prédominantes (2) L+V (> 80%) fréquentes (3) L rares (4) L+V+H rares
On note que le long de plans de fractures les inclusions de type (3) à une seule phase liquide
(généralement micrométriques) sont associées à des inclusions biphasées.
0
2
4
6
8
10
12
0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 -40
fré
qu
en
ce
Tfglace en °C
TfgQuartz
TfgDolomite
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
90
L’ensemble de ces inclusions a une morphologie ovoïde plus ou moins lobée ou de cristal
négatif de quartz.
Les mesures microthermométriques ont été effectuées sur les inclusions biphasées à bulle de
gaz de petite taille ainsi que sur les inclusions à cube de sel et bulle de gaz, figure 2-4 et 2-5.
Les températures de fusion de la glace mesurées permettent de calculer des salinités
comprises entre 2.8 et 11.2 wt% NaCl. Il est possible de mettre en évidence deux populations
avec une salinitée moyenne de 3.0 wt% NaCl pour l’une et de 9.3 wt% NaCl pour l’autre,
figure2-6. Ces deux familles d’inclusions sont pétrographiquement semblables. On remarque
de plus des températures d’homogénéisation moyenne de 305.5°C pour la population
d’inclusions présentant les salinités les plus élevées ainsi qu’une plus forte dispersion de
température d’homogénéisation, figure 2-7.
Figure 2-6 : Températures d'homogénéisation en fonction de la salinité dans les inclusions biphasées de
l'échantillon End09-07_06
0.0
50.0
100.0
150.0
200.0
250.0
300.0
350.0
400.0
450.0
500.0
0.0 2.0 4.0 6.0 8.0 10.0 12.0
Tem
pé
ratu
re d
'ho
mgé
né
isat
ion
en
°C
Salinité calculé en wt% NaCl
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
91
Figure 2-7 : Histogramme de fréquence des températures d’homogénéisation des inclusions fluides dans les
quartz de l’échantillon End09-07_06
2.4. Interprétations et perspectives
L’ensemble des données microthermométriques acquises a permis de calculer les isochores
figure 2-8.
En prenant l’hypothèse d’une couverture sédimentaire de 5km avec une densité de 2600
kg/m3 et d’un gradient géothermique de 40°C/km (cas idéal purement diffusif) on remarque
que les températures de piégeage données par les isochores sont légèrement plus élevées mais
proches des températures d’homogénéisation mesurées sur les inclusions triphasées à cube de
sel dans la dolomlite, aux environs de 210°C. Dans le cas des inclusions biphasées les
températures sont beaucoup plus variable mais dans l’ensemble plus élevées que celles
calculées sur les inclusions triphasées. Elles pourraient signifier un apport de chaleur local
plus important ou une mise en place à plus grande profondeur.
0
1
2
3
4
5
80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480
fré
qu
en
ce
Th en °C
Th Quartz Fréquence
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
92
Ces observations sont en accord avec les résultats précédemment acquis sur le gisement
d’Andrew lake (1) avec la mise en évidence de circulation de saumures de bassin à plusieurs
centaines de mètres dans le socle et (2) une histoire des fluides polyphasée avec des saumures
de moyenne température et des fluides peu salés de plus haute temperature, figure 2-9. Il
convient maintenant d’étudier les inclusions des cristaux de quartz et carbonates des autres
gisements du faisceau afin de confirmer ces tendances. Ces mesures pourrant être
éventuellement complétées par de la spectroscopie RAMAN, du LIBS ou encore de l’ablation
laser pour determiner la composition chimique des saumures.
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
93
Figure 2-8 : Isochores calculées à l’aide de Flincor en utilisant l’équation de Brown & Lamb, 1989
-500
0
500
1000
1500
2000
2500
3000
3500
50 150 250 350 450 550 650 750
TmodelConductif(30°C/km)
TmodelConductif(40°C/km)
END090513_1.1
END090513_1.8
END090513_1.9
END090513_2.1
END090513_2.2
END090513_2.4
END090513_2.15
END090513_4.3
END090513_4.4
END090513_5.1
END090513_5.2
END090513_5.3
END090513_5.4
END090513_6.1
END090513_7.1
END090513_7.2
Phydro(Bar)
Phydro(Bar)
END090706_1.1
END090706_2.2
END090706_2.3
P lihto
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
94
Figure 2-9 : Histogramme de fréquence des températures d’homogénéisation de l’ensemble des inclusions étudiées le long du faisceau structural de Kiggavik Andrew Lake
0
5
10
15
20
25
30
35
40
0
20
40
60
80
10
0
12
0
14
0
16
0
18
0
20
0
22
0
24
0
26
0
28
0
30
0
32
0
34
0
36
0
38
0
40
0
42
0
44
0
46
0
48
0
Fré
qu
en
ce
Temperature °C
HistoFReq_Th_Carbonates
HistoFReq_Th_Quartz Fréquence
Etude microthermométrique des inclusions fluides dans les quartz et dolomite associées aux minéralisations uranifères du faisceau structural Kiggavik-Andrew Lake
95
Réferences
Derome D, Cathelineau M, Cuney M, Fabre C, Lhomme T, Banks DA (2005) Mixing of Sodic and Calcic Brines and Uranium Deposition at McArthur River, Saskatchewan, Canada: A Raman and Laser-Induced Breakdown Spectroscopic Study of Fluid Inclusions. Economic Geology 100:1529-1545. doi: 10.2113/gsecongeo.100.8.1529.
Hoeve J, Quirt D (1984) Mineralization and host rock alteration in relation to clay mineral diagenesis and evolution of the Middle-Proterozoic Athabasca basin, Northern Saskatchewan, Canada Saskatchewan Research Concil Technical report. Saskatchewan Reasearch Council, pp 197.
Kotzer TG, Kyser TK (1995) Petrogenesis of the Proterozoic Athabasca Basin, northern Saskatchewan, Canada, and its relation to diagenesis, hydrothermal uranium mineralization and paleohydrogeology. Chemical Geology 120:45-89. doi: http://dx.doi.org/10.1016/0009-2541(94)00114-N.
Pagel M (1975) Détermination des conditions physico-chimique de la silicification diagénétique des grès Athabasca (Canada) au moyen des inclusions fluides. Comptes Rendus de l'académie des Sciences Paris 280:2301-2304.
Pagel M, Jaffrezic H (1977) Analyses chimiques des saumures des inclusionsdu quartz et de la dolomite du gisement d’uranium de Rabbit Lake(Canada). Aspect méthodologique et importance génétique. Comptes Rendus de l'Académie des Sciences 284:113-116.
Pagel M, Ahamdach N (1995) Etude des inclusions fluides dans les quartz des gisements d'uranium de l'Athabasca et du Thelon (Canada). Centre de Recherche sur la Geologie des matières premieres minerales et énérgétiques - CREGU, Vandoeuvre les Nancy, pp 1-10.
Illite & Uraninite geochronology
96
3. Illite & Uraninite geochronology
3.1. Introduction
Temporal constrains on alteration and mineralization events are of main importance for
geologists who deal with metallogenic interpretation of uranium deposition and more
particularly with the timing of deposition of the present uranium ore deposits. From the
previous study on petrography and mineralogy of both uranium ore bodies and alteration
haloes along the Kiggavik-Andrew Lake structural trend, uraninite and illite seems to be the
best mineral candidates for gaining the radio-chronological data necessary to refine the age
and the temporal relationships between mineralization and uranium alteration processes.
Uranium ore-forming minerals like uraninite are very likely to be remobilized in oxidizing
conditions, (via the oxidation of the U4+ to U6+ which is highly soluble in aqueous solutions).
Then, losses of radiogenic lead or gain of common lead can occur and mislead the
interpretation of the original crystallisation age. However, this could be seen as a great
advantage because uraninite resets may help to record the various remobilisation events since
the primary uranium deposition, either controlled by regional events (e.g. intrusion
emplacements, meteoric water circulation in faults and fractures) either controlled by far field
effects of the continental crust geodynamics (e.g. rifting, diagenesis, collision, uplift,
isostatic rebound).
3.2. Ar/Ar principle and method
The principle of the 40Ar/39Ar geochronology is a variant of the K / Ar method, based on the
fact that potassium rich mineral present elevated 40Ar/36Ar ratios due to the 40K decay
(Aldrich and Nier 1948). Then the amount of radiogenic 40Ar* is proportional to the initial
potassium content in the mineral and time.
Illite & Uraninite geochronology
97
In nature both stable isotopes (36Ar, 38Ar and 40Ar*) and radioactive ones (37Ar & 39Ar) are
presents. Then artificial irradiation allows the precise quantification of the initial 40K from the
relative abundance between argon isotopes and the argon produced via neutron irradiation
(39Ark), with the relations:
40K = 0.0000125 * 39K, and 39Ark = 40K * J’ with J’, the irradiation parameter.
Then the isotopic ratios and the combination of the different yields can give access to the
40Ar/39Ar age using the equation:
with λ the decay constant and J the irradiation parameter.
The J’ and J parameter constrains the abundance of potassium isotopes, the decay constant,
the neutron fluence, the effective cross section of the K (n, p) reaction, as well as the duration
of irradiation. These parameters are obtained from the co-irradiation of standard of known age
with the samples (Mitchell 1968).
One of the advantages of the Ar/Ar method over the conventional K/Ar is the step heating
degassing (Merrihue and Turner 1966). This is providing information about potential Ar
unrelated to the radioactive decay of potassium, and can possibly be plotted as an isochron
diagram comprising a plot of 40Ar/36Ar vs 39Ar/36Ar. Then one sample can give many ages,
and the presence or absence of plateau is critical for interpretation. The lack of plateau forces
to a more carful interpretation. Then ages resulting from the interpretation of Ar realised must
be taken more carefully. Such assessment and control over the data in not possible with the
K/Ar were the age is representative of the mean value of all the released radiogenic argon.
Then two types of ages can be calculated: (1) an average age comprising several steps that
define a plateau, and (2) a total fusion age, were all the measured steps are used, and then is
Illite & Uraninite geochronology
98
equivalent to a K/Ar age. Since the several decades the definition of the plateau varied
according to the analytical progress and the authors. As a general guideline, a plateau can be
defined a segment of the age spectrum which consist of 3 steps with overlapping age within
the analytical error (2σ) in which more than 50 % of the argon is released. All samples
were run as conventional furnace step heating analyses on bulk illite mineral separates. All
data are reported at the 1σ uncertainty level, unless noted otherwise. Furnace step heating
analyses produce what is referred to as an apparent age spectrum. The "apparent age" derives
from the fact that ages on an age spectrum plot are calculated assuming that the non-
radiogenic argon (often referred to as trapped, or initial argon) is atmospheric in isotopic
composition (40Ar/36Ar = 295.5).
3.3. Samples
The dataset of our geochronological study consists in 6 mineral Table 3-1 (1) Four of them
consist in illite and sudoite separates which were dated by the Ar/Ar method. Sudoite persists
in the illite concentrate because it was not possible to efficiently separate these two clay
minerals. They constitute a clay assemblage impossible to sort by any existing method of
mineral separation. However, it can be expected that sudoite which does not contain
potassium (or other alkali element) in its crystal structure has not significant influence on the
measured ages. Each clay sample was encapsulated prior to irradiation to avoid Ar losses
(Hess and Lippolt 1986; Foland et al. 1992) and processed in the Nevada Isotope
Geochronology Laboratory at the University of Nevada, Las Vegas, USA. A sudoite-rich,
sample (Bong42_25) was selected in order to test the timing of alteration comparatively with
zones where illite is dominant. The work hypothesis was a possible reset of the illite
geochronometer during the sudoite precipitation. (2) Two semi-massive uraninite samples
from the End Grid deposit were analysed via SIMS using the U/Pb geochronometer at the
CRPG-CNRS facility on a CAMECA IMS 1270 ion-probe. The analytical protocol is given in
Illite & Uraninite geochronology
99
(Alexandrov et al. 2000) and the ISOPLOT software was used for the isochron calculations
(Ludwig 1993).
Table 3-1 : Main characteristics of minerals samples selected for geochronology
Sample Depth Macroscopic description Illite Sudoite Method
End09_04_32/
9568-38
345.1 uraninite in fracture in a redox front zone,
bleaching
no data U/Pb
SIMS
End09_04_33/
9568-39
355.6 semi-massive pitchblend in a fracture parallel to
the foliation
xxx x “
Bong42_21 309.3 microfault gouge parallel to the foliation xx xx Ar/Ar
Bong42_25 347.7 pervasively altered metagraywacke x xxx “
Bong42_32 388.2 pervasively altered metagraywacke xx x “
Bong42_40 441.0 microfault gouge parallel to the foliation xxx x “
3.4. Results
3.4.1. Ar-Ar datation of illite
All the samples produced discordant age spectrum, while the K/Ca ratios were low and
consistent with illite separate. In addition the high radiogenic yields in agreement indicates
that the samples were not affected by recent alteration. The total gas ages obtained were 1248,
1072, 1033 and 952 Ma (Figure 3-1 and table 3-1). However most of the samples showed a
relatively complex age spectrum, and only one plateau age at 1124 9 Ma can be calculated
from the Bong42_40 sample (figure 3-1d). Nevertheless, some significant steps of the age
spectrum diagrams showing overlaps can cautiously be interpreted, as “pseudo-plateau”. This
age which doesn’t fully agree with the requirements for a plateau definition (in term of age
Illite & Uraninite geochronology
100
overlap and Ar released) may provide more knowledge on the alteration and mineralization
relationships. From these data, several groups of ages can be identified, near 1300 Ma in the
Bong4221 & 4225 samples and near 1100 Ma in the Bong4232 and Bong4240 samples. A last
an age around 1200 Ma can be also suspected with less confidence.
Figure 3-1 : Age spectrum of illites of the Bong prospect obtained from Ar/Ar datation method. a: Bong42_21;
b: Bong42_25; c: Bong42_32; d: Bong42_40.
Illite & Uraninite geochronology
101
Table 3-2 Ar/Ar geochronology data
step T
(°C) t
(min.) 36Ar 37Ar 38Ar 39Ar 40Ar %40Ar* % 39Ar rlsd Ca/K 40Ar*/39ArK Age (Ma) 1s.d. Bong42_21, Illite, 0.19 mg, J = 0.00543 ± 0.50%
1 450 12 0.118 0.023 0.192 8.963 1347.69 98.3 9.1 0.08033758 148.094449 1064.6 7.6 2 500 12 0.047 0.022 0.115 6.233 977.83 99.7 6.3 0.110502883 156.763618 1111.0 7.7 3 550 12 0.045 0.017 0.151 9.552 1608.99 99.8 9.7 0.055718043 169.307208 1176.2 8.1 4 600 12 0.050 0.022 0.194 13.161 2222.12 99.8 13.3 0.052332878 169.979488 1179.7 8.0 5 650 12 0.055 0.025 0.269 17.968 3362.74 99.8 18.2 0.043559211 188.752426 1272.8 9.1 6 700 12 0.049 0.028 0.345 22.443 4385.28 99.9 22.7 0.039058566 197.360166 1314.0 8.6 7 750 12 0.031 0.020 0.226 14.783 2902.95 100.0 15.0 0.042355226 197.627568 1315.3 8.9 8 800 12 0.029 0.015 0.062 3.602 814.771 100.0 3.7 0.130376126 223.734354 1434.6 9.3 9 850 12 0.027 0.016 0.021 1.242 323.665 100.0 1.3 0.403350707 248.229084 1539.8 9.8 10 910 12 0.036 0.014 0.016 0.541 153.107 100.0 0.5 0.810337177 250.430085 1549.0 10.2 11 970 12 0.042 0.016 0.014 0.187 58.036 99.9 0.2 2.680684089 167.943639 1169.3 9.5
Cumulative %39Ar rlsd = 100.0 Total gas age = 1248.2 7.3 Bong42_25, Illite, 0.39 mg, J = 0.00472 ± 1.55%
1 450 12 0.596 0.049 2.155 20.042 1901.65 91.0 20.3 0.077876847 87.679309 624.78 9.29 2 500 12 0.161 0.061 1.302 24.770 2048.34 98.3 25.1 0.078443549 81.899919 589.63 8.75 3 540 12 0.073 0.045 0.531 14.914 2595.82 99.6 15.1 0.096111195 174.883789 1085.74 14.15 4 570 12 0.044 0.028 0.323 9.758 2128.38 99.9 9.9 0.091401271 219.612617 1283.18 15.96 5 600 12 0.043 0.029 0.237 8.190 1882.00 99.9 8.3 0.112790305 231.224893 1331.09 16.47 6 640 12 0.222 0.033 0.278 9.022 2122.05 97.5 9.2 0.116511623 231.250191 1331.20 16.40 7 690 12 2.220 0.046 0.711 7.371 2242.50 72.7 7.5 0.198792401 223.065351 1297.56 16.93 8 740 12 0.050 0.014 0.036 1.443 298.336 99.3 1.5 0.309060685 410.064354 1942.77 20.67 9 840 12 0.153 0.023 0.089 2.286 448.787 94.6 2.3 0.320505207 179.954762 1109.24 14.65 10 1000 12 0.189 0.032 0.064 0.706 75.517 42.5 0.7 1.44433639 29.580690 235.79 5.23
Cumulative %39Ar rlsd = 100.0 Total gas age = 952.49 14.92 Bong42_32, Illite, 0.10 mg, J = 0.00474 ± 1.37%
1 400 12 0.069 0.014 0.118 2.727 294.022 96.7 5.3 0.164422178 101.868836 710.76 9.55 2 450 12 0.043 0.013 0.117 3.132 398.964 99.5 6.1 0.132933729 124.984666 839.36 10.62 3 480 12 0.031 0.009 0.103 3.076 429.522 99.9 6.0 0.093705459 137.874793 907.29 11.32 4 510 12 0.035 0.014 0.110 4.048 619.357 100.0 7.9 0.110763932 152.413632 980.95 11.96 5 540 12 0.042 0.021 0.126 5.367 852.669 99.8 10.5 0.125314216 158.622804 1011.52 12.25 6 570 12 0.032 0.016 0.128 6.002 995.231 100.0 11.7 0.085375188 166.133281 1047.81 12.65 7 600 12 0.036 0.016 0.135 6.078 1059.91 100.0 11.8 0.084307621 174.877712 1089.17 12.89 8 640 12 0.505 0.014 0.277 8.625 1632.74 91.9 16.8 0.051984331 175.153282 1090.46 13.08 9 690 12 4.233 0.029 1.037 7.700 2565.11 54.2 15.0 0.120620002 182.139769 1122.81 15.47 10 740 12 0.103 0.016 0.091 3.226 613.706 98.4 6.3 0.15884459 183.675258 1129.84 13.29 11 840 12 0.114 0.016 0.067 1.096 254.611 94.8 2.1 0.46758933 205.979005 1229.02 14.66 12 1000 12 0.179 0.016 0.043 0.242 102.156 66.6 0.5 2.118677458 209.431054 1243.90 17.20
Cumulative %39Ar rlsd = 100.0 Total gas age = 1032.96 13.94 Bong42_40, Illite, 0.26 mg, J = 0.00484 ± 1.38%
1 400 12 0.118 0.015 0.175 4.771 634.887 86.3 3.8 0.102158706 127.854730 869.02 11.06 2 450 12 0.063 0.022 0.195 5.649 780.443 99.0 4.5 0.126545782 136.870450 917.00 11.42 3 480 12 0.038 0.012 0.158 5.432 755.730 99.9 4.3 0.071781289 139.021735 928.27 11.56 4 510 12 0.039 0.013 0.183 7.532 1144.59 99.9 5.9 0.056081659 152.582126 997.69 12.33 5 540 12 0.042 0.012 0.216 10.217 1599.84 99.9 8.1 0.038163082 158.598822 1027.66 12.37 6 570 12 0.042 0.020 0.248 12.560 2017.40 99.9 9.9 0.051740144 161.907354 1043.93 12.58 7 600 12 0.043 0.024 0.248 13.829 2355.68 99.9 10.9 0.056390808 171.838464 1091.91 13.03 8 640 12 0.162 0.029 0.394 20.673 3642.17 99.9 16.3 0.045580701 176.431866 1113.67 13.20 9 690 12 2.722 0.038 1.105 27.837 5656.73 86.7 22.0 0.044355505 178.419659 1123.01 13.60 10 760 12 0.142 0.020 0.297 15.464 2798.37 98.9 12.2 0.042023694 180.891527 1134.55 13.36 11 1000 12 0.334 0.016 0.148 2.685 644.618 88.9 2.1 0.193633545 207.465883 1254.22 14.65
Cumulative %39Ar rlsd = 100.0 Total gas age = 1072.18 6.29
Plateau age = 1123.60 8.98
note: isotope beams in mV, rlsd = released, error in age includes J error, all errors 1 sigma 4 amu discrimination = 1.0598 ± 0.62%, 40/39K = 0.0086 ± 27.68%, 36/37Ca = 0.000256 ± 2.01%, 39/37Ca = 0.000658 ± 1.01% isotope beams in mV, rlsd = released, error in age includes J error, all errors 1 sigma (36Ar through 40Ar are measured beam intensities, corrected for decay for the age calculations)
Illite & Uraninite geochronology
102
3.4.2. SIMS U/Pb datation of uraninite
Uranium and lead isotopic ratios (206Pb/238U and 207Pb/235U) measured in samples End0904-32
and End0904-33 were plotted on Concordia diagrams, figure 3-2 & 3-3.
Figure 3-2 : U/Pb concordia diagram for End Grid veinlet mineralization
1600
1400
1200
1000
800
600
0.06
0.10
0.14
0.18
0.22
0.26
0.30
0.34
0.5 1.5 2.5 3.5
207Pb/
235U
206P
b/2
38U
Intercepts at
124±25 & 1293.1 ±6.2 [±8.4] Ma
MSWD = 27
KIGGAVIK (End Grid) - 9568-38
Illite & Uraninite geochronology
103
Figure 3-3 : U/Pb Concordia diagrams for End Grid semi-massive mineralization
Veinlet type mineralization data gave an upper intercept at 12936 Ma and a Mean Square
Weighted Deviation (MSWD) of 27, figure 3-2. The data for the semi-massive mineralization
gave an upper intercept of 118719 Ma and a MSWD of 8.3, Figure 3-3. In both case the
high MSWD indicates relatively scattered values.
3.5. Discussion
Until know most of the available literature on the Kiggavik area were TIMS U/Pb ages on the
mineralization or K/Ar geochronology on illite (c.f introduction). The gathered
geochronological data can be integrated with the literature data especially the recent work
done with in-situ techniques, more suitable to discriminate distinct events of mineralization
and alteration.
1400
1200
1000
800
600
400
200
00.00
0.04
0.08
0.12
0.16
0.20
0.24
0.28
0 1 2 3
207Pb/
235U
20
6P
b/2
38U Intercepts at
46 ± 57 & 1187 ± 19 [±20] MaMSWD = 8.3
KIGGAVIK (End Grid) - 9568-39
Illite & Uraninite geochronology
104
The Ar/Ar data obtained on illite from the Bong deposits can be compared with U/Pb in-situ
data ages on Bong uraninite (Sharpe 2013), as well as the age obtained on End mineralization,
Figure 3-4. Both the identified plateau and pseudo-plateau are within the errors range of the
U/Pb ages on uraninite. In addition, ages around 1300 Ma seems recurrent in all the analysed
samples. This age is in the same time frame as the MacKenzie dykes, so this event could be a
control of the mineralization via the far field tectonics related to Poseidon ocean opening.
They could be indicative of the first mineralization stage, but older ages cannot be totally
excluded. Nevertheless, the step heating doesn’t indicate that this age could be related to a
major reset due to the absence of ages older than 1300 Ma. The only possibility as showed in
the Bong4225 would be the presence of trace of unaltered metamorphic micas, giving a non
significant step of Hudsonian age. These ages are slightly younger than the 1403 Ma U/Pb
TIMS age on uraninite or the K/Ar ages on illite 138624 Ma and 1362 21 Ma at Kiggavik
(Farkas 1984; Miller and LeCheminant 1985). However, the comparison between the bulk
ages and in situ or Ar/Ar via step heating degassing may be not relevant as heterogeneities
and numerous remobilizations affected uraninite. In fact, remoblization could result in
contamination by common lead and apparently older ages. The younger ages around 1100
Ma are possibly connected to a later event of uranium remobilization. They could also be
related to the Grenville orogen.
Finally, it can be noted that similar ages have been obtained for both the uranium
mineralization and the illite crystallization in the associated alteration halo in the Bong and
the End uranium mineralizations. This confirms a close temporal relationship between the two
process, highlighting so the interest of alteration minerals as marker of the paleoconditions of
uranium deposition. The fact that similar ages have been obtained in the two studied areas
confirms also the regional extension of the alteration and mineralization processes. This also
indicates that reactivation of both local and regional faults allowed the fluid circulation.
Illite & Uraninite geochronology
105
Finally, the ages obtained in the uranium deposits along the Kiggavik-Andrew-lake structural
trend indicate that alteration and mineralization processes were active over a large span of
time (⋍200MA) which is not so different of the span of time reported for alteration
mieralization processes in the Athabasca basin (Jefferson et al., 2007).
Illite & Uraninite geochronology
106
Figure 3-4 : Summary of new geochronological data on alteration and mineralization at Kiggavik with comparison to tectonic or thermal events affecting the Canadian shield
during the Paleoproterozoic, data from (Fahrig 1987; Rainbird et al. 2003; Davis et al. 2011; Peterson et al. 2002; Turner et al. 2001; Sharpe 2013)
Illite & Uraninite geochronology
107
3.6. References
Aldrich LT, Nier AO (1948) Argon 40 in Potassium minerals. Phys Rev 74. Alexandrov P, Cheilletz A, Deloule É, Cuney M (2000) 319 ± 7 Ma crystallization age for the Blond
granite (northwest Limousin, French Massif Central) obtained by U/Pb ion-probe dating of zircons. Comptes Rendus de l'Académie des Sciences - Series IIA - Earth and Planetary
Science 330:617-622. doi: http://dx.doi.org/10.1016/S1251-8050(00)00201-9. Davis WJ, Gall Q, Jefferson CW, Rainbird RH (2011) Fluorapatite in the Paleoproterozoic Thelon Basin:
Structural-stratigraphic context, in situ ion microprobe U-Pb ages, and fluid-flow history. Geological Society of America Bulletin 123:1056-1073. doi: 10.1130/b30163.1.
Fahrig WF (1987) The tectonic settings of continental mafic dyke swarms: Failed arm and early passive margin In: Halls HC, Fahrig WF (eds) Mafic dyke swarms. Geological Association of Canada Special Paper, St John's, Nfld, pp 331-348.
Farkas A (1984) Mineralogy and host rock alteration of the Lone Gull deposit Internal report. Urangesellschaft, Frankfurt am Main, pp 45.
Foland KA, Hubacher FA, Arehart GB (1992) 40Ar39Ar dating of very fine-grained samples: An encapsulated-vial procedure to overcome the problem of 39Ar recoil loss. Chemical Geology
102:269-276. doi: http://dx.doi.org/10.1016/0009-2541(92)90161-W. Hess JC, Lippolt HJ (1986) 40Ar/39Ar ages of tonstein and tuff sanidines: New calibration points for
the improvement of the Upper Carboniferous time scale. Chemical Geology: Isotope
Geoscience section 59:143-154. doi: http://dx.doi.org/10.1016/0168-9622(86)90066-7. Ludwig KR (1993) Isoplot:excel based program for plotting radiogenic isotopes. U.S. Geological
Survey, pp 1-42. Merrihue C, Turner G (1966) Potassium-argon dating by activation with fast neutrons. Journal of
Geophysical Research 71:2852-2857. doi: 10.1029/JZ071i011p02852. Miller AR, LeCheminant AN (1985) Geology and uranium metallogeny of Proterozoic supracrustal
successions, central District of Keewatin, N.W.T with comparisons to northern Saskatchewan Geology of uranium deposits. Canadian Institute of Mining and Metalurgy, pp 167-185.
Mitchell JG (1968) The argon-40argon-39 method for potassium-argon age determination.
Geochimica et Cosmochimica Acta 32:781-790. doi: http://dx.doi.org/10.1016/0016-7037(68)90012-4.
Peterson TD, Van Breemen O, Sandeman H, Cousens B (2002) Proterozoic (1.85-1.75 Ga) igneous suites of the Western Churchill Province: granitoid and ultrapotassic magmatism in a reworked Archean hinterland. Precambrian Research 119:73-100.
Rainbird RH, Hadlari T, Aspler LB, Donaldson JA, LeCheminant AN, Peterson TD (2003) Sequence stratigraphy and evolution of the Paleoproterozoic intracontinental Baker Lake and Thelon basins, western Churchill Province, Nunavut, Canada. Precambrian Research 125:21-53.
Sharpe R (2013) The geochermistry and geochronolgy of the Bong uranium deposit, Thelon Basin, Nunavut, Canada Department of Geological Sciences. University of Manitoba, Winnipeg, Manitoba.
Turner W, Richards J, Nesbitt B, Muehlenbachs K, Biczok J (2001) Proterozoic low-sulfidation epithermal Au-Ag mineralization in the Mallery Lake area, Nunavut, Canada. Miner Deposita 36:442-457. doi: 10.1007/s001260100181.
The basal Thelon Formation at Kiggavik
108
4. The basal Thelon Formation at Kiggavik
At Kiggavik, Thelon Formation is not widely encountered on actual land ARC land holdings,
and mostly represented by a strip of sandstones outcrops located at the North of the Granite
Grid prospect, close to the Thelon fault escarpment and basal conglomerates outcrops, at the
WNW of Kiggavik camp and in the St Tropez area, south of Schultz Lake. All studied
samples presented here where taken from outcrops in the Granite (labeled as GGx) & St
Tropez areas as well as in the historical Th18 BP drillhole, located 10 kilometers NNW of
Kiggavik.
Nevertheless, as the connection between the Thelon Basin and the mineralization system at
Kiggavik appears more and more preeminent, an overview of local petrographic and
mineralogical properties of these sandstones would provide additional informations for the
metallogenic interpretation of the Kiggavik area.
4.1. Methods
XRD diffraction were performed using a Bruker D8 diffractometer, on the 2- 65° 2θ range
using a 0.02 °2θ step a d se o d ou ti g ti e. Cu a ode X-ray tube set up with a 40kV
acceleration tension and 40mA current, 1° fixed divergence slit.
Transmission Fourier Infrared (FT-IR) spectra were recorded with a Nicolet 760 FT-IR
spectrometer equipped with a Potassium Bromide (KBr) beamsplitter and a DTGS-KBr
detector. Acquisitions were performed in the 400 – 4000 cm-1 (mid infrared range) with a
4cm-1 resolution. Pellets suitable for analysis were made using 1 mg of clay separates, used
for XRD measurement, and grounded in an agate mortar with 150 mg of KBr. The mixture
was therefore pressed in a vacuum die with 10 tons per cm2 of compression. Pellets were dried
24 hours at 120°C prior to measurements to avoid hygroscopic water in KBr. For each
spectrum 100 scans were cumulated after a background acquisition.
The basal Thelon Formation at Kiggavik
109
Electron microprobe measurements on clay minerals were done on a Cameca SX100 using
natural and synthetic standards for calibration. Albite, anortite and orthose, diopside, garnet
and MnTiO3 respectively for Na, Ca, K, Si, Fe, Mn, and Ti, with a column setting with a
15kV acceleration tension and a 10nA beam current.
Quartz oxygen isotopes compositions measurements were performed in situ by secondary ion
mass spectrometry (SIMS) on a CAMECA IMF 7f ion microprobe, at the University of
Manitoba. A ~2 nA primary beam of Cs+ was accelerated at 10kV and focused to a 10 x 15
m spot using a 100 m aperture in the primary column. An offset of 200-volts was used to
eliminate molecular ion interferences (Fayek et al. 2002; Riciputi and Greenwood 1998). Ions
were detected with a Balzers SEV 1217 electron multiplier coupled with an ion-counting
system using an overall deadtime of 52 ns. Two isotopes of oxygen, 16O- and 18O-, were
detected by switching the magnetic field. Analyses comprised 70 cycles and lasted ~10
minutes (Sharpe 2013). All stable-isotope data are presented in the δ-notation relative to the
appropriate standard. Oxygen is reported relative to Vienna Standard Mean Ocean Water (V-
SMOW) in units of per mil (‰) and are calculated using the following equation: δ18O (‰) =
(Rsample / RV-SMOW -1) * 103. Additional informations on SIMS are provided in appendix.
Chemical bulk rock analysis ICP-MS on major and traces elements were performed by the
Service d’Analyses des Roches et Minéraux (SARM) in CRPG, Nancy, France
4.2. Sandstones regional setting
The unconformity is mostly visible along the Thelon fault through the tectonic contact, the
sandstones being generally found on the Northern side of the fault, Figure 4-1a. A significant
vertical displacement, up to 200 meters, has been recognized from drillholes along this fault
The basal Thelon Formation at Kiggavik
110
exhibiting a horst and graben structure (P.Wollenberg, pers. Comm.). Then in one
compartment, both basement rocks at the topographic surface and the unconformity are
eroded while in the other compartment tens or hundreds of meters of sandstones are still
present above the unconformity. This feature reveals that the actual position of the Kiggavik
trend deposits known form to surface up to several hundred meters into the basement rocks
may have been formed deeply and thus are possibly the expression of deep seated
unconformity type uranium deposits. The normal movements with a dextral component
interpreted from the kinematic markers on fault surface, Figure 4-1b, are consistent with the
regional ones and are observed on the both Thelon and judge Sisson faults and are also
marked by significant alteration associated with hydraulic and tectonic breccias. Alteration is
expressed with a zone of intense hematization centered on the fault core which intensity
decrease rapidly in the damage zones in both foot and hanging walls. Into the fault core
hematization zones are forming alternating corridors of silicified / desilificied / hematized
rocks dominantly expressed in the Woodburn metasediments but also in the Archean or
Proterozoic quartzites. Hydraulic and tectonic brecciation is also present in the sandstones
above the unconformity along the Thelon fault zone Figure 4-1f. The lateral change form
strongly altered to fresh rocks is relatively sharp (over less than tens of meters) with
hematization being more disseminated and patchier in a dominantly chloritic metasediments.
Moreover at the vicinity of these regional tectonic structures, the general trend of flat flying
foliation is reworked and vertically reoriented, Figure 4-1c.
The basal Thelon Formation at Kiggavik
111
The basal Thelon Formation at Kiggavik
112
Figure 4-1a : Thelon fault escarpment where the Thelon Formation sandstones are tectonically in contact with
the underlying Woodburn Group metasediments, view looking toward the NNW, outcrop located at the north of
the Granite Grid area on CAMECO corp. ground (checked jointly with R. Hunter, CAMECO & C. Jefferson,
GSC); b, Detail of the previously indicated fault, looking at the handing wall the surface is showing quartzite
fragments dragged into the fault and indicating a normal with a dextral component displacement; c Angular
unconformity between the Thelon sandstones and the locally steep foliation of Woodburn Group metasediments,
strong red-brick hematization, at Unconformity lake (Forum’s ground); d, symmetrical ripple marks develloped
on the Thelon sandstones at Unconformity lake; e, red siltstone facies of the basal Thelon formation; f, hydraulic
fracturation breccias with sub angular sandstones fragments cemented by hydrothermal quartz at 110.9 meter,
with unconformity at 126.4m , BP historic drillcores; g, Polymictic conglomerate at the base of the Thelon
Formation in the St Tropez area, gravel to pebble boulder size elements of red siltite, gneisses and abundant
quartzite in a siliceous and hematitic matrix.
The sedimentary cover overlying the unconformity is formed of gritty to conglomeratic,
moderately to weakly sorted, and locally cross bedded, matrix supported sandstones
containing abundant lithic fragments of basement rocks (various gneisses, quartzite).
Lenticular to isopachous, metric intercalation of red siltstone beds are present within the
sandstones. Finally conglomerates seems to fill paleovalleys Figure 4-1e, d, g. in which
sediments may have been deposited in a relatively high energy, continental environment, at
shallow depth as are indicating from the observed symmetrical ripple marks, characteristic of
the oscillating waves effects Figure 4-1d.
4.3. Bulk-rock chemistry of the Basal Thelon sandstones
Bulk rock chemical analysis from the basal Thelon Formation are representative of quartz
arenite sandstones totally depleted in Na, Mg and Ca elements with only Al as major element
in addition to the strongly predominant Si (table 4-1). In the sandstones samples, the
The basal Thelon Formation at Kiggavik
113
aluminum content ranges from 2 to 8 % and can be essentially assigned to the presence of
kaolinite (in absence of significant amount of K), while iron (less than 1%) is principally
assigned to hematite. The very low potassium amount of sandstones can be related to detrital
micas and locally to traces of illite related to later incipient hydrothermal alteration. The
higher potassium content measured in the siltite sample (GG3a) is representative of the high
content of detrital micas in the sample. All these data are indicative of the absence of
significant amount of feldspar in the sandstones of the basal Thelon formation investigated in
the Kiggavik area.
Table 4-1 Major and traces elements concentration of basal Thelon sandstones (sst) from the NE St Tropez
(NESTP4) and Granite Grid (GG) areas. Red siltites from Granite Grid are represented by the GG3a sample
SiO2 Al2O3 Fe2O3 MnO MgO CaO Na2O K2O TiO2 P2O5 PF Zr Th U NESTP4 sst 91.50 4.57 0.96 0.01 0.03 < L.D. 0.01 0.41 0.11 0.04 1.51 52.42 5.35 0.70 GG3b sst 93.25 4.36 0.22 0.00 0.02 < L.D. 0.02 0.28 0.13 0.07 1.46 83.88 8.58 0.40 GG3c sst 91.70 4.93 0.24 0.00 0.02 < L.D. 0.01 0.25 0.08 0.04 1.81 51.12 6.07 0.39 GG4 sst 91.46 4.94 0.15 0.00 < L.D. < L.D. 0.01 0.22 0.07 0.03 1.88 50.05 5.47 0.34 GG5 sst 95.01 2.50 0.16 0.00 0.04 < L.D. 0.01 0.61 0.07 0.03 0.58 66.38 5.29 0.34 GG7 sst 87.19 8.06 0.61 0.00 0.02 < L.D. < L.D. 0.33 0.07 0.05 2.79 64.70 5.30 0.44 GG3a siltite 82.74 8.98 1.94 0.00 0.16 0.77 0.02 2.33 0.34 0.28 2.08 68.89 23.40 0.92
La Ce Pr Nd Sm Eu Gd Tb Dy Ho Er Tm Yb Lu ΣREE 21.08 32.63 3.46 10.60 1.31 0.23 0.77 0.11 0.52 0.09 0.26 0.04 0.32 0.05 71.19 29.04 50.28 5.18 15.88 2.08 0.40 1.28 0.15 0.56 0.07 0.20 0.03 0.24 0.04 105.23 19.57 33.48 3.46 11.10 1.50 0.31 0.85 0.10 0.38 0.06 0.18 0.03 0.24 0.04 71.11 18.49 18.61 3.18 9.76 1.15 0.23 0.52 0.06 0.27 0.04 0.13 0.02 0.18 0.03 52.54 11.96 21.40 2.18 7.09 1.02 0.22 0.64 0.07 0.32 0.05 0.15 0.03 0.20 0.03 45.20 18.72 35.23 3.47 11.30 1.65 0.35 1.16 0.14 0.67 0.11 0.32 0.05 0.37 0.06 73.28 92.91 133.00 19.44 72.43 12.31 2.30 7.17 0.74 2.08 0.21 0.60 0.09 0.73 0.12 343.52
Considering the trace elements, the basal sandstones can be characterized by very low
uranium concentrations (0.3 to 0.9 ppm) and U/Th ratios which range between 7.6 and 21.7.
In addition, sandstones are also characterized by light REE (La to Eu) > to heavy REE (Gd to
Lu) in the chondrite normalized patterns, Figure 4-2. Moreover the (La/Yb)ch ratios are
ranging from 34 to 82. Such fractionation is very common in weathering processes where
The basal Thelon Formation at Kiggavik
114
residual products are enriched in LREE and depleted in HREE (Duddy 1980; Nesbitt 1979,
(Braun et al. 1990).
Figure 4-2: chondrite normalized (Evensen et al. 1978) REE patterns for sandstones and siltites at the base of the
Thelon Formation
4.4. Petrography and mineralogy
According to the available sampling, petrographic and mineralogical study of sandstones
samples is not representative of the whole diagenetic phenomenon throughout the Thelon
basin. Its main goal is to describe in more details the basin / basement relationships at the
vicinity of the N70 trend Thelon fault which is non graphitic and non mineralized, but need to
be accounted for a fault of regional interest for the prospection of uranium mineralization in
the Kiggavik area.
All hand samples present a well developed cementation of the intergranular porosity by very
fine grained “cherty quartz”. Such silica cement trapped diagenetic APS minerals (see the
0.1
1
10
100
1000
La Ce Pr Nd Sm Eu Gd Tb Dy Ho Er Tm Yb Lu
NESTP4
GG3b
GG3c
GG4
GG5
GG7
GG3a
Siltite
Sandstones
The basal Thelon Formation at Kiggavik
115
paragenetic sequence in chapter 2) as well as large kaolinite vermicules or fragments of
aggregated quartz / kaolinite material of detrital origin.
Three different generations of quartz can be identified in these cemented sandstones: (1)
detrital, angular to sub rounded grains, (2) syntaxial quartz overgrowth forming 10 to 20
micrometer rims around detrital quartz grains, and (3) very fine grained microcrystalline
quartz (Folk and Weaver 1952) sealing all the remaining porosity of the sandstone, figure 4-
3a. The quartz overgrowths display evidence of stopping at the contact with the kaolinite
vermicules, Figure 4-3b, while the microcrystalline quartz cement not only heal the porosity
but show evidences of jigsaw texture suggesting a fluid assisted brecciation. Such hydraulic
fracture together with a matrix formed of a mosaic of tiny quartz crystals, is indicative of a
brutal event of fluid-rock interaction (strong oversaturation of the solution versus quartz)
during which nucleation is favored rather crystal growth.
According to their textural characteristics, three different types of kaolinite minerals have
been distinguished: (1) smalls euhedral crystals (3 * 3m) disseminated in the cemented
porosity (possibly neoformed or fragments of larger size kaolinite), Figure 4-3a, 4-3b; (2)
large vermicular kaolinite up to 0.5 x 0.2 mm which occurred either as individual crystal
either as aggregates, Figure 4-3c; and (3) composite aggregates of detrital quartz grains and
kaolinite, Figure 4-3d.
The basal Thelon Formation at Kiggavik
116
Figure 4-3 : a, epitaxial diagenetic quartz overgrowths (Q2) and (Q3) microcrystalline quartz cement; b, large
kaolinite booklets floating in the cemented porosity with evidence of stopping of the epitaxial growth of
diagenetic quartz overgrowth (Q2), c, aggregate of large, (up to 0.5mm length) kaolinite booklets in the
sandstone porosity, d, composite quartz and kaolinite lithic grain (red dotted circle); e, kaolinite & quartz lithic
grain showing evidence of later illitization; f, detrital quartz grain cross cut by a fracture filled by
microcrystalline quartz.
The basal Thelon Formation at Kiggavik
117
In addition it can be noted that micrometer grained size hematite grains are observed between
the booklets of kaolinite vermicules, as well as disseminated in the porosity in absence of any
trace of associated illitization. These iron oxides, likely hematite, are quite abundant in the
sandstone porosity, as lath and detrital, sub rounded grains, both cemented by the APS
minerals and the microcrystalline quartz, Figure 4-4a & b. It can be noted that a later
generation of hematite is also present in association with illite and APS minerals fillings of
fractures which cross cutt the microcrystalline quartz cement (see part B, chapter 1, on APS
minerals).
Lastly, one centimeter clay filled fracture cross cutting the basal Thelon Formation sandstone
in one of the historical BP drillcore site (located around 10 kilometers at the NW of the
Kiggavik camp, collar coordinates unknown), showed a white clay mineral with a blocky
habit characteristic of diagenetic dickite, figure 4-4c & d &e.
A detailed SEM observation and a chemical mapping of the pore filling material of the
cemented sandstones close to the unconformity (figure 4-5a to d) permitted to identify
fragments of detrital material mostly composed of aluminum-rich minerals associated with
disseminated micrograins of quartz and tiny crystals of cerium oxide. The chemical
composition of the aluminum-rich minerals agree with that of aluminum oxi-hydroxide such
as diaspore or boehmite ( 35.5 % Al, 60.1 % O, 2.8 % Si), Figure 4-4f which contain
significant amount of cerium (Figure 4-4g & h and table 4-2). In addition, some
disseminated cerium oxide (cerianite) are frequently associated with aluminum oxi-
hydroxides minerals, Figure, 4-4f & g.
The basal Thelon Formation at Kiggavik
118
The basal Thelon Formation at Kiggavik
119
Figure 4-4 : a hematite lath cemented by microcrystalline quartz, b hematite grain cemented by APS minerals
and microcrystalline quartz, c kaolinite booklet cemented by microcrystalline quartz (Q3) cementing the
sandstone porosity; d & e blocky dickite (+detail view on the picture) filling a fracture cross cutting the quartz
cemented Thelon sandstones; f, aluminum oxy - hydroxide minerals coating associated with cerium rich grains
on detrital quartz grain later cemented (by Q3), g aluminum hydroxide and kaolinite/dicktite blocky crystals and
associated with cerium oxides (cerianite), h, Ce-rich (over 4%) aluminum hydroxide matrix EDS spectra.
Figure 4-5 : SEM EDS chemical element maps (Si, Al, Ce) of aluminum rich compounds, identified as oxy
hydroxide, a SEM secondary electron image, b, Silicon image, c, Aluminum and silicon composite images, and
d, silicon and cerium composite image.
The basal Thelon Formation at Kiggavik
120
Table 4-2 : Chemical composition of the Al-rich mineral phase identified in the detrital material filling the pore
space of sandstone overlying the basal unconformity between the Thelon sedimentary formation and the
basement rocks (sample GG7).
Al2O3 SiO2 K2O CaO Fe2O3 Ce2O3 total
71,34 6,45 0,53 0,32 0,05 5,12 83,80
65,04 6,91 0,12 0,23 0,07 4,42 76,78
69,75 12,60 0,32 0,26 0,33 2,75 86,00
4.5. Crystallochemical properties of kaolin minerals
The crystal-chemistry of the kaolin group minerals occurring at the base of the Thelon basin
has been done using XRD, mid infra-red spectroscopy and EMPA.
As showed on XRD diffraction patterns, figure 4-6a, kaolin group minerals are well
represented in the basal Thelon sandstones were they have been preserved from subsequent
hydrothermal alteration. In both oriented as well as randomly oriented powder all the kaolin
group minerals are identified by their strong d00l and d002 diffraction peaks at 7.16 Å & 3.57
Å respectively. According to the obtained XRD patterns, both kaolinite and dickite have been
identified in the basal Thelon samples. Kaolinite and dickite polytype has been identified
within all the samples which contain kaolin minerals disseminated within the quartz cemented
porosity (fig 4a). Evidences of a kaolinite/dickite mixing is given by (1) the broadening of the
020 diffraction line resulting from the contribution of both kaolinite (4.47 Å) and dickite (4.44
Å) 020 diffraction lines and (2) specific dickite diffraction peaks in the 35-40 2 theta range,
Figure 4a. Moreover, using the peak intensity ratio between the 132,204 reflections of the
dickite polytype and the 20-2 ,1-31 reflections of the kaolinite polytype (Beaufort 2014) the
proportion of dickite in the bulk kaolin material can be estimated to 35%. In addition to these
estimations, pure dickite polytype has been identified in the late fractures which crosscut the
cemented sandstone (Th18_3), Figure 4-6b.
The basal Thelon Formation at Kiggavik
121
Figure 4-6 : X-ray diffraction patterns for Thelon Formation kaolin group minerals, showing, a a
kaolinite/dickite mixture, and b, a pure dickite fracture. Both diffractograms of kaolinite and dickite display the
diffraction peaks attributed to highly ordered minerals.
The basal Thelon Formation at Kiggavik
122
These results are confirmed by the mid IR technique which appears to be the most effective to
discriminate kaolinite and dickite using the differences in position and relative intensity of
OH stretching bands, figure 4-7. In the GG3 and GG7 samples (disseminated kaolin minerals)
the four bands observed at 3696, 3669, 3653 and 3620 cm-1 are in agreement with data given
in literature for the hydroxyl-stetching bands region of kaolinite (Farmer 1974). In addition
the good distinction between the bands at 3669 and 3653 cm-1, as well as the narrow and
symmetrical shapes of the other bands are characteristic of a rather well ordered kaolinite
microcrystals. It can be noticed that the inflexion at 3598 cm-1 observed on the GG3 spectra is
characteristic of the Al- Fe3+ OH vibration and thus indicate the presence of structural ferric
iron in the kaolinite of certain samples (Petit and Decarreau 1990; Petit et al. 1999).
The 3706, 3654 and 3621 cm-1 bands observed in the FTIR spectrum of the kaolin minerals
from the late fracture which crosscut the cemented sandstone (Th18_3 sample) are typical of a
pure dickite polymorph, figure 4-7.
GG3b (kaolinite)
GG7 (kaolinite)
Th18_3 Fracture (dickite) 0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
3550 3600 3650 3700 3750 3800
Wavenumbers (cm-1)
Ab
so
rba
nce
ab
itra
ry u
nits
Figure 4-7 : Mid Infra-red spectra of Thelon formation Kaolin Group minerals in the OH-stretching domain.
The basal Thelon Formation at Kiggavik
123
4.5.1. Crystallographic properties of kaolin group minerals: order /disorder
The structural order of the kaolin group minerals could be investigated using classical
Hinckley index of crystallinity calculation method on XRD diffraction patterns and IR
spectroscopy spectra (Hinckley 1963; Crowley and Vergo 1988). However, this approach
requires the absence of quartz in the analysed kaolin material and the study of samples series,
a major difficulty in our area where most of the sandstones are eroded and in which quartz
microcrystals cannot be separted from kaolin minerals. Nevertheless, the crystallographic
properties giving the level of structural order of kaolinite and dickite can be assessed using
both XRD and IR (Brindley and Brown 1980).
Then the basal Thelon formation kaolinite, are matching with the order criteria of prominent
basal reflections 001 and 002 together with well defined 02l and 11l reflection in the 19-33°
(2θ range (Hayes 1963; Keller et al. 1966). In addition, in the range, 35-40° (2θ), the 13l, 20l
reflections occurs with the 003 basal reflection. These reflections forming two groups of
triplets in the well ordered kaolinites (Brindley and Brown 1980), Figure 4-6a. Lastly, the
tiny shoulder observed on the right sides of diffraction peaks and due to the Kαβ reflection
indicates the presence of highly ordered crystals. Such a high order is moreover coherent with
the presence of dickite diffraction lines.
As in kaolinite, dickite diffraction lines can be used to characterize the level of structural
order. Then even if dickite is generally seen as an highly ordered polymorph of the kaolin
mineral group, some differences in crystallinity have been described in dickite series
(Brindley and Porter 1978). Then, the better ordered samples as the Th18_3 dickite, show all
the X-ray powder diffraction lines (Newnham and Brindley 1956; Newnham 1961), Figure 4-
6b.
The basal Thelon Formation at Kiggavik
124
4.5.2. Chemistry of kaolinite minerals
The electron microprobe data acquired on the kaolinite vermicules confirmed their relatively
high iron content (up to 0.73 % Fe2O3), with a moderate compositional variability in each
single crystal, Table4-3 4-9 & figure4-9. Two distinct populations of kaolinite can be
identified on the basis of their morphology & chemistry. The first one being iron poor with
virtually no iron while the second is iron rich with an average content around 0.5 % wt Fe2O3.
However they are both represented by large booklets and minute crystals in the
microcrystalline quartz matrix.
Table 4-3 : Representative microanalysis of the two kaolinite morphologies present in the basal Thelon
Formation sandstones
Na2O MgO Al 2O3 SiO2 K 2O CaO TiO 2 MnO Fe2O3 H2O total
Large kaolinite Fe 0.01 0.05 38.00 46.99 0.07 0.05 0.00 0.01 0.67 14.00 99.85
Large kaolinite 0.00 0.05 38.30 47.47 0.02 0.07 0.00 0.00 0.06 14.00 99.96
Minute kaolinite 0.01 0.01 38.77 47.16 0.08 0.04 0.00 0.06 0.35 14.00 100.47
Figure 4-8 : plot of the chemical microanalyses of kaolin minerals from the basal Thelon Formation sandstones
in the Al2O3-Fe2O3 cross plot diagram.
y = -0.19x + 38.31
36.0
37.0
38.0
39.0
40.0
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80
Al2
O3
%
Fe2O3 %
Basal Thelon Fm sandstones kaolinites
The basal Thelon Formation at Kiggavik
125
Figure 4-9 : Electron microprobe chemical transects in the aggregates of kaolin of the basal Thelon sandstones
of the Kiggavik area. Average distance between the punctual analyses ranges from 10 to 20 micrometers
according to the size of the kaolin grains.
In addition, the kaolinite crystals tends to be chemically homogeneous throughout the grain
with no significant compositional variation near the edges or along the crystallographic c or
ab axis, as shown by the microchemical transects, Figure 4-10 & 4-11.
Figure 4-10 : Location of some of the electron microprobe transects in kaolinite (GG4 sample)
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Fe2
O3
wt
%
number of analysis points in the transect
GG4_kaol_Trsct2
GG4_kaol_Trsct3
GG4_kaol_Trsct4
GG4_kaol_Trsct6
GG3b_KaoITrsct4
GG3b_KaolTrsct2
The basal Thelon Formation at Kiggavik
126
4.6. Microcrystalline quartz cement chemistry and in situ composition of
oxygen isotopes
Figure 4-11 : Silica and alumina content measured in detrital and microcrystalline quartz. Note that the
measurements were performed on a SEM-EDS
In addition to their petrographic characteristics, the microcrystalline quartz reveals a peculiar
chemical signature with an increase in aluminum content relatively to the detrital quartz,
figure 4-12. Such variation in Al content has been described in burial diagenesis in successive
quartz overgrowths generations (Tournier 2010). In addition the aluminum content of quartz,
as hydrous Al species, seems to be correlated to the amount of defects and the rate of crystal
growth (Ihinger and Zink 2000). Then, the oxygen isotopes composition has been investigated
to better constrain the paleoconditions at which they crystallized.
0.00
0.20
0.40
0.60
0.80
1.00
1.20
1.40
1.60
1.80
2.00
96.00 97.00 98.00 99.00 100.00
Al 2
O3
SiO2
Detrital Quartz
Microcrystalline quartz
The basal Thelon Formation at Kiggavik
127
Figure 4-12 : Histogram of 18O values measured in microcrystalline (Qtz3) and detrital quartz from the basal
Thelon Formation sandstones.
Table 4-4 : SIMS oxygen isotopic data and detrital quartz grain and the microcrystalline quartz (Qtz3).
Mineral 18O/16O FF 1σ 18OV-SMOW (‰) T (°C)
GG4_Qtz3-1 Quartz 1.848399 0.9241131 1.2 32.5 54 GG4_Qtz3-2 Quartz 1.850852 0.92533948 1.3 33.9 48 GG4_Qtz3-3 Quartz 1.857398 0.92861217 1.2 37.5 35 GG4_Qtz3-4 Quartz 1.862655 0.93124043 1.2 40.4 25 GG4_Qtz3-5 Quartz 1.84891 0.92436857 1.2 32.8 53 GG4_Qtz3-6 Quartz 1.847598 0.92371263 1.3 32.0 56 GG4_Qtz3-7 Quartz 1.860585 0.93020553 1.2 39.3 29 GG4_Qtz3-8 Quartz 1.854224 0.92702532 1.3 35.7 41 GG4_Qtz3-9 Quartz 1.857503 0.92866467 1.2 37.6 35 GG4_Qtz3-10 Quartz 1.86143 0.93062799 1.3 39.8 27 GG3_Qtz3-1 Quartz 1.861797 0.93081147 1.2 40.0 27 GG3_Qtz3-2 Quartz 1.860428 0.93012703 1.2 39.2 29 GG3_Qtz3-3 Quartz 1.864177 0.93200136 1.2 41.3 22 GG3_Qtz3-4 Quartz 1.856241 0.92803373 1.2 36.9 37 GG3_Qtz3-5 Quartz 1.855203 0.92751478 1.2 36.3 39 GG4_Detrital-Gr-1 Quartz 1.826909 0.9133691 1.2 20.5 102 GG4_Detrital-Gr-2 Quartz 1.831189 0.9155089 1.2 22.9 85 GG4_Detrital-Gr-3 Quartz 1.826232 0.91303063 1.2 20.1 106 GG4_Detrital-Gr-4 Quartz 1.820232 0.91003091 1.2 16.8 135
0
1
2
3
4
16 18 20 22 24 26 28 30 32 34 36 38 40 42
δ18OV-SMOW (‰)
The basal Thelon Formation at Kiggavik
128
The δ18O values obtained from in situ measurements in the microcrystalline quartz which
cement the porosity of the sandstones range between 31.9 and 41.3 per mil with an error of
1.2 (1σ). The data presents two modes centered on 33 ‰ and 40 ‰, Figure 4-13 & table 4-4.
For comparison the detrital grain were ranging from 16.8 to 22.9 per mil, in a similar range
than other Thelon sandstones detrital quartz grains (Hiatt et al. 2007). Then using the
extrapolation of classical quartz-water fractionation (Clayton et al. 1972) and AlphaDelta
program (Beaudoin and Therrien 2004; Beaudoin and Therrien 2009), the calculated
temperature range from from 1°C up to 35°C and are rather questionable. However, the use of
most recent fractionation equation for low temperature quartz - kaolinite-water system,
between 0 and 130°C (Méheut et al. 2007), provides more realistic temperatures. A water
composition in equilibrium with sea water was chosen for temperature calculation as a more
saline water composition can be assumed in an intracratonic, possibly warm environement,
with shallow water depht. The obtained temperatures show a bimodal distribution, each mode
being centered on 27 °C and 52°C respectively.
4.7. Discussion
Petrographic studies carried on the basal Thelon Formation sandstones around Kiggavik,
showed peculiar mineralogy and textures with (1) the large kaolinite crystals embedded in the
sandstone matrix and (2) the quartz-kaolinite composite grains, (3) the local presence of Al
oxides or oxide-hydroxides associated with cerium oxides, (4) evidences of dickite as fracture
filling material and (5) a sandstone porosity sealed by microcrystalline quartz, figure 4-14.
Another very interesting point is the preservation of most of the basal Thelon formation of the
The basal Thelon Formation at Kiggavik
129
postdating hydrothermal alteration which is strongly developed along the major faults of the
underlying basement rocks. Then, the petrography and the mineralogy of this compartment of
basal Thelon sandstone formation, makes possible an attempt to reconstruct the early history
of the bottom part of the Thelon basin (from sedimentation to the end of diagenetic
evolution).
Figure 4-13 : Paragenetic sequence of minerals determined in the basal Thelon formation. See Part B chapter 2
on APS minerals for more details on the crystal-chemistry of the different aluminium phosphate minerals.
The detrital mineralogy raises questions about the origin of the material leading to such
assemblage as well as the genetic processes involved in there formation prior to erosion
transport and sedimentation. Diagenetic processes and paleoburial conditions have to be
considered at the view of the kaolinite/ dickite transition evidenced from crystallographic
properties in this study, with respect to previous works on kaolin diagenesis in siliciclastic
basins (Beaufort et al. 1998; Shutov et al. 1970; Eckhardt and Von Gaertner 1962; Eckhardt
1965).
The basal Thelon Formation at Kiggavik
130
4.7.1. On the origin of detrital and diagenetic Al bearing minerals in the
basal Thelon Formation
The presence of detrital aluminum minerals with kaolinite, hematite aluminum phosphate
sulfate and local cerium oxide raise the question of the source of the detrital material. Similar
minerals assemblages have been described in various actual or recent lateritic profiles or
bauxites (Valeton 1972; McFarlane 1976; Loughnan and Bayliss 1961; Braun et al. 1990;
Curtis and Spears 1971). In addition the crystallochemical properties of kaolinite with
frequent and relatively high (from 0.3 up to 2% Fe2O3) structural Fe3+ observed in the Thelon
Formation kaolinite is also common in kaolinites formed in laterite under intense weathering
(Herbillon et al. 1976; Malden and Meads 1967; Tardy and Nahon 1985; Cantinolle et al.
1984). Moreover it has been showed that the amount of structural iron is of great influence on
the kaolinite crystallinity, with an increase of disorder positively correlated to the iron content
(Mestdagh et al. 1980; Brindley et al. 1986).
On the contrary in the kaolinite and quartz composite grains, the morphology of kaolinite is
by far more irregular and indicate that the lithic fragments was originally of analogous
composition, and possibly formed by a mechanical mixing of the two minerals. In addition,
the sub rounded shape for such a fragile assemblage also indicates a likely moderate distance
of transport.
As described in many studies, three type of kaolin are widely recognized depending on their
textural properties: (1) as micas replacement, where authigenic kaolinite crystallization takes
place in between expended detrital micas flackes (Nedkvitne and Bjorlykke 1992; Ehrenberg
et al. 1993; Macaulay et al. 1993), (2) as vermicules and (3) as blocky kaolinite (Lanson et al.
2002). The last two types raise numerous questions on the processes responsible for their
crystallization including temperature, pH, H+/K+ ratio and reaction kinetics.
The basal Thelon Formation at Kiggavik
131
Then, the well developed crystals and the pristine shape of kaolinite booklets observed at the
base of the Thelon Formation sandstone is thus in agreement with an in-situ formation in the
sandstone porosity. Moreover petrography showed that the diagenetic quartz overgrowths
(Qtz2) are stopped by the presence of the kaolinite vermicule present in the porosity.
Then it could seem in contradiction with the relatively high crystallographic order of the
kaolinite present in the basal Thelon Formation. However, the evidence of neoformation of
hematite between kaolinite stackes or in place the fine grain hematization observed in the
sealed porosity surrounding the grain might be directly linked to the high iron initially present
in the kaolinite. Such feature, could be explained by diagenetic dissolution recrystallization
processes in which iron is partially taken out from the kaolinite to precipitate as hematite.
Then, it could also indicate that the detrital kaolinites could have been iron richer and that the
vermicules of kaolinite are pro parte recrystallized sedimentary kaolinites or generated
through aluminum oxy-hydroxides silicification processes or neoformation (Trolard and
Tardy 1989).
Nevertheless, our interpretation of such mineral assemblages at the view of present geological
is limited by the two following points:
(1) the atmosphere redox and pH conditions during the Paleoproterozoic paleoweathering
events are not clearly defined but probably developed in a more reducing environment than
today (Partin et al. 2013). Then the condition would have been less oxidizing with
consequences of an higher iron mobility, and a preferential integration of iron in
phyllosilicates rather than in iron oxides or sulfide that would also suggest that sulfur wasn’t
available in the system (2) the persistence of aluminum hydroxides, minerals common in
laterite or bauxite is very rarely found in the sediments and even more in the sandstone
affected by deep burial diagenesis.
The basal Thelon Formation at Kiggavik
132
4.7.2. Sandstone quartz cementation, some contradictory observations
The Churchill province of the Canadian Shield presents several occurrences of silicified
weathering profiles or silicified sediments which were described as silcretes, as in the Thelon
or Hornby Bay Basins (Gall 1994; Ross and Chiarenzelli 1985; Ross 1983). Oxygen isotopes
on the quartz cements are then a critical tool to assess the crystallization conditions but the
comparison with modern cherts and careful use of the actualism principle is necessary. Indeed
some differences in formation environments and forming processes have been established
between Precambrian and Phanerozoic cherts (Maliva et al. 2005). In addition several
isotopic composition of the quartz is then dependent of the crystallization temperature, as well
as the salinity and the isotopic composition of the fluid in equilibrium with the quartz.
Relatively high oxygen isotopes values on quartz are the expression of very low temperature
processes not uncommon in surface environments (Kolodny et al. 2005). In addition such high
silica rich rocks as cherts or silcretes had been studies for a long time and used as indicators
of surface temperature or weathering conditions through geological times (Knauth and
Epstein 1976; Sayin and Jackson 1973).
In addition, the present results are partially in agreement with the petrography and oxygen
isotopes of the quartz cements at the base of the Thelon Formation (Hiatt et al. 2007). These
authors described isopachous microcrystalline quartz rims fringing the detrital quartz grains,
in both eolian facies of Thelon sandstones and the Pitz formations, without any prior
diagenetic overgrowth. In fact, at Kiggavik the microcrystalline is not present as comb
structure and seems to be developed after a first stage of diagenetic overgrowth. However, the
oxygen isotopic composition is quite similar with values between the microcrystalline quartz
at Kiggavik and the quartz cements or even some of the latter quartz generation filling the
porosity described by the same authors. Then two opposite trends are presents, which may
indicate different porosity evolutions throughout the Thelon formation sandstones. In one case
The basal Thelon Formation at Kiggavik
133
the earlier cements have the highest δ18O values up to 33 ‰ with a 26 ‰ mean (Hiatt et al.
2007), while the present study the microcrystalline quartz have a maximum δ18O values value
of 41.3 ‰ with a 37 ‰ mean. These significantly higher values are in agreement with very
low temperatures but contradictory with the petrographic evidence of a rapid precipitation
associated with hydraulic fracturation.
Finally, the sedimentary features as the ripples marks observed at the base of the Thelon
indicates relatively shallow environment. In addition, in similar Paleoproterozoic Basins as
the Athabasca Basin Boron, and Chlorine isotopes studies have proposed an evaporated sea
water as sources for the ore related brines (Richard et al. 2011; Richard et al. 2013). Then, the
position over the Tropics during the Paleoproterozoic (Betts et al. 2008) of these huge
intracratonic basins could be considered as relatively close environment favourable for water
evaporation. This raise numerous question about the water isotopic composition, and might
suggest that the δ18O (H2O) would have been higher. If so, the calculated temperature from
the microcrystalline quartz cement would be necessarily shifter toward higher temperatures.
Then, the temperature would be even more compliant with an hydrothermal origin for the
microcrystalline quartz cement, possibly in relaton with a brutal pressure change.
4.8. Conclusion
Petrography and cystal-chemistry gave a series of arguments to relate the composition of the
clay minerals of the basal Thelon Formation sandstones to a product of paleo weathering
profile dismantling, possibly lateritic or bauxitic, developed during the regolithisation of the
Archean and Paleoproterozoic basement rocks which preceeded the sandstone deposition.
This is also supported by the very specific location of the studies sandstones in the vicinity of
The basal Thelon Formation at Kiggavik
134
an ancient fault system that may have been reactivated with a tectonic control of the
sedimentation, with very little transport of the basin filling material studied. Such settings are
then highly favorable to preserve the fragile clay / quartz composite of the dismantled
weathering profile, or the large kaolinite later recrystallized as massive vermicules in the
porosity during burial diagenesis, as well as the aluminum oxi-hydroxides such as diaspore or
boehmite.
The diagenesis also includes the precipitation of the quartz overgrowths as well as the
recrystallisation of the coarse grained vermicules of ordered kaolinite in the porosity. This
reasonably indicates that significant burial depth may have been reach to generate such a
degree of order in the kaolinite, prior to the microcrystalline quartz cementation. Finally, this
might also be supported by even later fracture controlled precipitation under even higher
pressure condition with the presence of the cross cutting dickite fracture.
Then the basis of the Thelon sandstones, at this particular location are recording the early
basin filling history and the weathering processes active before the Thelon deposition. The
structural control of the sedimentation is giving a good indication on the source material due
to the expected short distance of transport. Finally this preservation of kaolin group mineral
from both the sedimentary and diagenetic histories highlight the fact the sandstone had been
chemically isolated in the Kiggavik area. This could appear contradictory with the occurrence
of authigenic K-feldspar and illite diagenetic cements described in the Thelon basin (Renac et
al. 2002). Such a fact probably indicates that the Thelon Basin was compartmented during its
evolution history as did many others younger basins worldwide.
The basal Thelon Formation at Kiggavik
135
4.9. References
Beaudoin G, Therrien P (eds) (2004) The web stable isotope fractionation calculator. Elsevier. Beaudoin G, Therrien P (eds) (2009) The updated web stable isotope fractionation calculator.
Elsevier. Beaufort D, Cassagnabère A, Petit S, Lanson B, Berger G, Lacharpagne JC, Johansen H (1998)
Kaolinite-to-dickite reaction in sandstone reservoirs. Clays minerals 33:297-316. Beaufort D (2014) Chapitre2: contribution des argiles à la reconstitution de l'histoire
thermique des bassins sédimentaires In: Pagel M (ed) Bassins sédimentaires: les marqueurs de leur histoire thermique. EDP Sciences.
Betts PG, Giles D, Schaefer BF (2008) Comparing 1800 – 1600 Ma accretionary and basin processes in Australia and Laurentia: Possible geographic connections in Columbia. Precambrian Research 166:81-92. doi: http://dx.doi.org/10.1016/j.precamres.2007.03.007.
Braun J-J, Pagel M, Muller J-P, Bilong P, Michard A, Guillet B (1990) Cerium anomalies in lateritic profiles. Geochimica et Cosmochimica Acta 54:781-795. doi: http://dx.doi.org/10.1016/0016-7037(90)90373-S.
Brindley GW, Porter ARD (1978) Occurencies of dickites in Jamaica-order and disordered varieties. American Mineralogist 63:554-562.
Brindley GW, Brown G (1980) Crystal structures of clay minerals and their X-ray identification. Mineralogical Society, London, UK.
Brindley GW, Kao C-C, Harrison JL, Lispicas M, Raythatha R (1986) Relation between structural disorder and other characteristics of kaolinites and dickites. Clays abd Clay Minerals 34:239-249.
Cantinolle P, Didier P, Meunier JD, Parron C, Guendon JL, Bocquier G, Nahon D (1984) Kaolinites ferrifères et oxy-hydroxydes de fer et d'alumine dans les bauxites des Canonnettes (S.E. de la France). Clay Minerals 19:125-135.
Clayton RN, O'Neil JR, Mayeda TK (1972) Oxygen isotope exchange between quartz and water. Journal of Geophysical Research 77:3057-3067. doi: 10.1029/JB077i017p03057.
Crowley J, K., Vergo N (1988) Near-infrared reflectance spectra of mixtures of kaolin-group minerals:use in clay mineral studies. Clays and Clay Minerals 36:310-316.
Curtis CD, Spears DA (1971) Diagenetic developement of kaolinite. Clays and Clay Minerals 19:219-227.
Duddy LR (1980) Redistribution and fractionation of rare-earth and other elements in a weathering profile. Chemical Geology 30:363-381. doi: http://dx.doi.org/10.1016/0009-2541(80)90102-3.
Eckhardt FJ, Von Gaertner HR (1962) Zur enstehung un umbildung der kaolinit Kolhentonsteine. Forschr Geol Rheinl Westf 3:623-640.
Eckhardt FJ (1965) Über den einfluss der tempertur auf den kristallographishen ordnungsgrad von kaolinit Proc Int Clat Conf Stockhlom, pp 137-145.
Ehrenberg SN, Aagaard P, Wilson MJ, Fraser AR, Duthie DML (1993) Depth-dependent transformation of kaolinite to dickite in sandstones of the Norwegian continental shelf. Clay Minerals 28:325-352.
Evensen NM, Hamilton PJ, O'Nions RK (1978) Rare-earth abondances in chondritic meteorites. Geochimica et Cosmochimica Acta 42:1199-1212.
Farmer VC (ed) (1974) The infrared spectra of minerals. Mineralogical Society, London.
The basal Thelon Formation at Kiggavik
136
Fayek M, Kyser K, Riciputi LR (2002) U and Pb isotope analysis of uranium minerals by ion microprobe and the geochronology of the McArthur River and Sue zone uranium deposits, Saskatchewan, Canada. Canadian Mineralogist 40:1553-1569.
Folk RL, Weaver CE (1952) A study of the texture and composition of chert. American Journal of Science 250:498-510. doi: 10.2475/ajs.250.7.498.
Gall Q (1994) The Proterozoic Thelon paleosol, Northwest Territories, Canada. Precambrian Research 68:115-137. doi: http://dx.doi.org/10.1016/0301-9268(94)90068-X.
Hayes JB (1963) Kaolinite from Warsaw geodes, Keokuk region, Iowa. Proceedings of the Iowa Academy of Sciences 70:261-272.
Herbillon AJ, Mestdagh MM, Vielvoye L, de Rouane EG (1976) Iron in kaolinite with special reference from tropical soils. Clay Minerals 2:201-220.
Hiatt EE, Kyser TK, Fayek M, Polito P, Holk GJ, Riciputi LR (2007) Early quartz cements and evolution of paleohydraulic properties of basal sandstones in three Paleoproterozoic continental basi s: Evide e f o i situ δ O a alysis of ua tz e e ts. Che i al Geology 238:19-37. doi: http://dx.doi.org/10.1016/j.chemgeo.2006.10.012.
Hinckley DN (1963) Variability in "crystallinity" values among the kaolin deposits of the coastal plain of Georgia and South Carolina In: Swineford A (ed) Clays and Clay Minerals, Proc 11th Natl Conf. Pergamon Press, New York, Ottawa, Ontario, pp 229-235.
Ihinger PD, Zink SI (2000) Determination of relative growth rates of natural quartz crystals. Nature 404:865-869.
Keller WD, Pickett EE, Reesman AL (1966) Elevated dehydroxylation temperature of the Keokuk geode kaolinite Proc Int Clay Conf. Jerusalem, pp 75-85.
Knauth LP, Epstein S (1976) Hydrogen and oxygen isotope ratios in nodular and bedded cherts. Geochimica et Cosmochimica Acta 40:1095-1108. doi: http://dx.doi.org/10.1016/0016-7037(76)90051-X.
Kolodny Y, Chaussidon M, Katz A (2005) Geochemistry of a chert breccia. Geochimica et Cosmochimica Acta 69:427-439.
Lanson B, BEAUFORT D, Berger G, Bauer A, Cassagnabère A, Meunier A (2002) Authigenic kaolin and illitic minerals during burial diagenesis of sandstones: a review. Clay Minerals 37:1-22.
Loughnan FC, Bayliss P (1961) The mineralogy of bauxite deposits. American Mineralogist 46:207-217.
Macaulay CI, Fallick A, Hasezeldine RS (1993) Textural and isotopic variations in diagenetic kaolinite form the Magnus oilfield sandstones. Clay Minerals 28:625-639.
Malden PJ, Meads RE (1967) Substitution by Iron in Kaolinite. Nature 215:844-846. Maliva RG, Knoll AH, Simonson BM (2005) Secular change in the Precambrian silica cycle:
Insights from chert petrology. Geological Society of America Bulletin 117:835-845. doi: 10.1130/b25555.1.
McFarlane MJ (1976) Laterite and landscape. Academic Press, London. Méheut M, Lazzeri M, Balan E, Mauri F (2007) Equilibrium isotopic fractionation in the
kaolinite, quartz, water system: Prediction from first-principles density-functional theory. Geochimica et Cosmochimica Acta 71:3170-3181. doi: http://dx.doi.org/10.1016/j.gca.2007.04.012.
Mestdagh MM, Vielvoye L, Herbillon AJ (1980) Iron in kaolinite. II. The relashionship between kaolinite and iron content. Clay Minerals 15:1-13.
The basal Thelon Formation at Kiggavik
137
Nedkvitne T, Bjorlykke K (1992) Secondary porosity in the Brent Group (Middle Jurassic), Huldra Field, North Sea; implication for predicting lateral continuity of sandstones? Journal of Sedimentary Research 62:23-34. doi: 10.1306/d426787a-2b26-11d7-8648000102c1865d.
Nesbitt HW (1979) Mobility and fractionation of rare earth elements during weathering of a granodiorite. Nature 279:206-210.
Newnham RE, Brindley GW (1956) The structure of dickite. Acta crystallographica 9:759-764. Newnham RE (1961) Refinement of the dickite structure and some remarks on
polymorphism in kaolin minerals. Mineralogical Magazine 32:231-243. Partin CA, Bekker A, Planavsky NJ, Scott CT, Gill BC, Li C, Podkovyrov V, Maslov A, Konhauser
KO, Lalonde SV, Love GD, Poulton SW, Lyons TW (2013) Large-scale fluctuations in Precambrian atmospheric and oceanic oxygen levels from the record of U in shales. Earth and Planetary Science Letters 369–370:284-293. doi: http://dx.doi.org/10.1016/j.epsl.2013.03.031.
Petit S, Decarreau A (1990) Hydrothermal (200°C) synthesis and crystal chemistry of iron-rich kaolinites. Clay Minerals 25:191-196.
Petit S, Madejova J, Decarreau A, Martin F (1999) Charcterization of octaedral substitutions in kaolinites using near infrared spectroscopy. Clays and Clay Minerals 47:103-108.
Renac C, Kyser K, Durocher K, Dreaver G, O'Connor T (2002) Comparison of diagenetic fluids in the Proterozoic Thelon and Athabsca Basins, Canada: implications for protracted fluid histories in stable intracratonic basins. Can J Earth Sci 39:113-132.
Richard A, Banks DA, Mercadier J, Boiron M-C, Cuney M, Cathelineau M (2011) An evaporated seawater origin for the ore-forming brines in unconformity-related u a iu deposits Atha as a Basi , Ca ada : Cl/B a d δ Cl a alysis of fluid inclusions. Geochimica et Cosmochimica Acta 75:2792-2810. doi: http://dx.doi.org/10.1016/j.gca.2011.02.026.
Richard A, Boulvais P, Mercadier J, Boiron M-C, Cathelineau M, Cuney M, France-Lanord C (2013) From evaporated seawater to uranium-mineralizing brines: Isotopic and trace element study of quartz–dolomite veins in the Athabasca system. Geochimica et Cosmochimica Acta 113:38-59. doi: http://dx.doi.org/10.1016/j.gca.2013.03.009.
Riciputi LR, Greenwood JP (1998) Analysis of sulfur and carbon isotope ratios in mixed matrices by secondary ion mass spectrometry: implications for mass bias corrections. International Journal of Mass Spectrometry 178:65-71. doi: http://dx.doi.org/10.1016/S1387-3806(98)14086-1.
Ross GM (1983) BigBear erg: a Proterozoic intermontane eolian sand sea in the Hornby Bay group, Northwest Territories, Canada In: Brookfield ME, Ahlbrandt TA (eds) Eolian Sediments and Processes. Elsevier, Amsterdam, pp 483-519.
Ross GM, Chiarenzelli JR (1985) Paleoclimatic significance of widespread Proterozoic silcretes in the Bear and Churchill provinces of the northwestern Canadian Shield. Journal of Sedimentary Research 55:196-204. doi: 10.1306/212f8666-2b24-11d7-8648000102c1865d.
Sayin M, Jackson ML (1973) Scanning electron microscopy of cherts in relation to the oxygen isotopic variation of soil quartz. Clays and Clay Minerals 23:365-368.
Sharpe R (2013) The geochermistry and geochronolgy of the Bong uranium deposit, Thelon Basin, Nunavut, Canada Department of Geological Sciences. University of Manitoba, Winnipeg, Manitoba.
The basal Thelon Formation at Kiggavik
138
Shutov VD, Alexandrova AV, Losievskaya SA (1970) Genetic interpretation of the polytypism of the kaolinite group in sedimentary rocks. Sedimentology 15:69-82.
Tardy Y, Nahon D (1985) Geochemistry of laterites, stability of Al-goethite, Al-hematite, and Fe (super 3+) -kaolinite in bauxites and ferricretes; an approach to the mechanism of concretion formation. American Journal of Science 285:865-903. doi: 10.2475/ajs.285.10.865.
Tournier F (2010) Mécanismes et contrôle des phénomènes diagénétiques en milieu acide dans les grès de l'Ordovicien glaciaire du bassin de Sbaa, Algérie UMR CNRS IDES. Paris Sud 11, Orsay, pp 333.
Trolard F, Tardy Y (1989) A model of Fe3+-kaolinite, Al3+-goethite, Al3+-hematite equilibria in laterites. Clay Minerals 24:1-21.
Valeton I (1972) Bauxites. Elsivier, Amsterdam.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
139
5. Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
Riegler Thomas & Beaufort Daniel.
Paper in preparation
5.1. Introduction
Carbonaceous materials (CM) in the early earth history are always controversial with two
possible origin, one involving life where bitumen are deriving from classical kerogen thermal
evolution, while the second is the expression of abiotic synthesis of organic compounds in
hydrothermal or magmatic systems e.g. via Fischer-Tropsch type synthesis (FTT) (Shock
1990; Gize 1999; Foustoukos and Seyfried 2004; McCollom and Seewald 2006; Horita 2005;
Ueno et al. 2004; Curiale 1986; McCollom 2013). Both processes are being tracked by
specific geochemical signatures such as molecular markers, carbon and sulfur stable isotopes,
together with petrographic evidences. Such carbonaceous materials, referred as bitumens,
have been frequently identified within the alteration halos surrounding the Mid-Proterozoic
unconformity type uranium deposits (Hoeve and Sibbald 1978; Hoeve et al. 1980; Hoeve and
Quirt 1984; Pagel et al. 1980; Sangély et al. 2007). The reducing potential, the source and the
distribution in brecciated and altered Archean to Paleoproterozoic metamorphic basement or
in the Meso-Proterozoic sedimentary cover of such material have been discussed for uranium
metallogenesis (Leventhal et al. 1987; Kyser et al. 1989; Landais and Dereppe 1985; Yeo and
Potter 2010; Sangély et al. 2007) without strong evidence for ore control, while it was
invoked as ore controlling parameter in gold bearing veins (Mastalerz et al. 1995). On the
contrary in the Paleoproterozoic Oklo mineralization the paragenesis indicates a more obvious
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
140
link between bitumen and oil occurrences with uranium precipitation, in a petroleum-like
system were faults creates trap and path for oil migration as well as favorable contact between
marine black shale and the bitumen hosting deltaic sandstones (Gauthier-Lafaye and Weber
1989; Nagy et al. 1991).
In previous works in the Athabasca Basins, bitumen is considered to post-date the main
uranium mineralization stage (Wilson et al. 2002; Leventhal et al. 1987) or is sometimes seen
to be contemporaneous to it (Alexandre and Kyser 2006). However the host rock is composed
of a various package of metasediments or meta-igneous rocks devoid of any carbon other than
graphite on faults. Although several lithologies are known as potential sources of oil with
including the Phaneroic blackshales of the Exshaw Formation (Sangély et al. 2007), who
might have migrated downwards trough 1500 meters of Athabasca Group sandstones and
several hundred meters below the unconformity, along the fault and fracture network
controlling the uranium mineralization. The main debate being the in situ formation versus the
migration of the organic compounds.
The aim of this work is to identify and to characterize the chemistry and structure of the
carbonaceous materials associated with the uranium mineralizations at the Southeastern
margin of the Meso-Proterozoic Thelon Basin. Then geochemical, isotopic, petrographic and
crystallographic evidences with comparison with (1) similar type of mineralization in the
Athabasca Basins and (2) laboratory synthesis of organic compounds will gives the basis of
discussion for the genesis and emplacement of such material several hundred meters below
the eroded unconformity at Kiggavik in alteration envelopes surrounding one of the major
uranium ore zones in Canada outside the Athabasca basin. Lastly the new knowledge on the
crystal structure of carbonaceous material in unconformity type uranium mineralization will
give a new perception for metallogenesis and approach in ore deposits studies.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
141
5.2. Geological setting and petrography
Uranium mineralization (mainly uraninite and coffinite) at Kiggavik is composed of several
ore bodies but one at Bong is particularly rich in carbonaceous material very often easy to
distinguish with the strong cabbage / garlic smells associated with its presence. All the ore
shoots are surrounded by tens of meters large clay alteration envelopes developed in Achean
metagraywackes belonging to the Woodburn Lake Group (Farkas 1984; Miller and
LeCheminant 1985) and controlled by fault and fracturation corridors and slip opening along
the foliation plan. Then all the primary metamorphic silicates (feldspars, muscovite, biotite,
chlorite) are replaced by an alteration paragensis dominated by illite and sudoite (Al-Mg
chlorite) in various proportions displaying similar feature as many other unconformity
associated uranium mineralization in Canada and Australia (Beaufort et al. 2005; Laverret et
al. 2006; Hoeve and Quirt 1984; Polito et al. 2004), as in the present work. Accessory
minerals in the non altered are largely represented by zircon, monazite, titanium oxides,
magnetite and pyrite, that latter being quite abundant in places where the medium to fine grain
graywacke tends to be more pelitic.
Carbonaceous materials are exclusively found within clay alteration zones as fracture filling
up to 1 centimeter thick of massive carbonaceous material, a dark black, stainy, relatively
hard and brittle material showing concoïdal fractures. Dots of similar material are presents
scattered in the argilized host rock. The other expression of carbonaceous material are black
to dark gray fractures and coating (no visible CM aggregate under the SEM) on foliation plan
with a typical cabbage / garlic smell, Figure 5-1a, b. There distribution doesn’t seems to
follow any spatial organization other than alteration but rich zones but most of it is found at
the hanging wall of the alteration envelop in Bong where sudoite is slightly dominant over
illite. In addition there are frequently intersected with several drillholes in the same area
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
142
roughly over several a tens of meters radius. The CM nodule are ranging from millimetric to
micrometric in diameter and are developed in an illite and sudoite clay matrix showing in
places thin coatings of uraninite are presents as fracture fillings of the CM nodules Figure 5-
1c, d. Uraninite is found dissemintated in the carbonaceous matrix as mint euhedral crystals,
often partially altered to coffinite and organized in pseudo concentric rings forming
alternating bands with the massive carbon carbon in which elevated U and Cu level are
noticeable Figure 5-1e. Finally dissolution pits have been identified at the surface of the
carbonaceous material forming circular to oblate holes of a few micrometers in diameter
Figure 5-1f.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
143
Figure 5-1 : Carbonaceous materials occurrences at Kiggavik. 1a: carbonaceous material along the foliation plan
and filling millimetric fractures in altered metagraywacke, S : schistosity, BG5101. 1b: detail of fracture filling
material under binocular lense, button of carbonaceous material in the intergrain porosity BG5101. 1c:
carbonaceous nodule in argilized metagrawacke BG4326. 1d: Carbonaceous material nodule in an illite and
sudoite matrix, some microfrature plans are coated with uraninite BG4238. 1e Disseminated uraninite partially
altered to coffinite and chalcopyrite in massive carbonaceous material. 1f Hollow point in massive carbonaceous
material
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
144
5.3. Samples & Methods
Representative samples of each type of carbonaceous material had been chosen. In addition a
particular care had been taken in the sampling itself in taking the samples just after drilling to
avoid contamination as much as possible, as well as alteration of the carbonaceous material by
bacteria.
All the 3 samples from the Bong prospect are representative of the two types of carbonaceous
material found in the alteration halos in association with uranium mineralization. One is
composed of massive carbonaceous material (MCM) (BG4238), at the hanging wall of fault
zone, while the second is set as diffuse impregnations of carbonaceous material (DiffuseCM)
as staining and coating on fractures and foliation plans in a highly argilized rock with the
BG4326 and 5101 samples. Samples were collected respectively at 428, 316 and 286 meters
below the actual erosion surface.
5.4. Results
The both type of material have been analyzed with the most suitable method in order to
extract all the possible information from (1) volatile organic compound disseminations and
(2) the massive carbonaceous material, and tie the two concurrencies in the alteration history.
The two expression of carbon bearing compounds are very distinct in term of petrographic
expression but also in term of carbon content from tenth of per mil to tens from tens of
percent in the massive CM.
5.4.1. GC-MS pyrolysis
Several organic sulfur compounds have been identified in GC-MS flash pyrolysis using both
600 / 400°C as well as low temperature extraction of volatiles at 300°C in dichloromethane
with a HMDS & TMAH treatment. Both methods yield similar results with the identification
of low molecular weight and volatile compounds: carbon disulfide, dimethyldisulfide
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
145
(DMDS) and dimethyltrisulfide in the black to grayish disseminations in the argilized
metagraywacke. Such compounds haven’t been detected in the massive carbonaceous sample
and the identified alcanes or aromatic are possible contaminations. Sulfur dioxide is also
present in all studied samples and is very likely the expression of sulfides roasting,
chalcopyrite in that case. All these molecules are responsible for the characteristic smell
associated with some areas in the alteration zone, even if in traces. The trace characters of
these compounds make their identification.
5.4.2. X-Ray Diffraction
The massive carbonaceous material 66 % C doesn’t exhibit any reflection of the graphite
diffraction pattern in a whole rock randomly oriented powder mount of the <50 μm size
fraction. This surprising feature raises the question of the type of bonds between the Carbon
atoms and the structure of this material, Figure 5-2. The only minerals identified are
uraninite, coffinite, chalcopyrite, johannite [Cu(UO2)(SO4)2(OH)2.8H2O)] and studtite
[UO4.4H2O] according to XRD data from (Walenta 1974). In addition an oriented slide of the
infra 0.1 μm size fraction extracted by ultracentrifugation haven’t shown any diffraction peak
for graphite either, only a broad baseline indicating either an amorphous material or a
structure without enough layers stacked to induce the X-ray diffraction. Such characteristic
possibly reflect a graphene structure or amorphous graphitic material.
Then in order to probe the structure of C-C bonds and possible spatial organization the Raman
spectroscopy and transmission electron microscopy appears to be the most suitable
techniques.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
146
Figure 5-2 : Randomly oriented powder XRD diffractogram of massive carbonaceous material, (5-65° 2theta
scan, 0.02 stepsize and 4 seconds counting time). Abbreviations, Ccp (1): Chalcopyrite; Coff (2): coffinite; Uran
(3) uraninite; Joh (4): johannite and Stu (5): studtite.
5.4.3. Raman spectroscopy
Raman spectra obtained on massive CM show two pronounced bands at about 1340 (D) and
1600 (G) cm-1 as well as a relatively marked fluorescence responsible for the moderate
baseline but also hiding the second order Raman bands (overtone) in the 2000 – 4000 cm-1
range, Figure 5-3. Of these two bands the first one, broad and relatively intense, is attributed
to disordered carbons and edges effects (D band) while the second is the graphite band (G)
linked to the sp2 C-C configuration of the graphene planes (Chu and Li 2006; Jehlička et al.
2003; Tuinstra and Koenig 1970b). The shift toward higher wavelength values of the G band
seems to be indicative of extremely small crystallites (Tuinstra and Koenig 1970a). In
addition, the spectrum decomposition using pseudo Voigt function leads to the identification
of 4 different bands respectively at 1188, 1334, 1510 & 1601 cm-1, and a final fitted profile
(cross) with a reasonable match with the original spectrum Figure 5-3. The graphite G & D
5 15 25 35 45 55 65 2θ
graphite main diffraction line
Coff
2
Ccp 1
Uran
Joh 1 1
1
2
2
2 2 2 2 3
3 2 2 3 3 4 4
2 4
Stu
5 5 5 5 5 5
1
2
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
147
bands at 1334 & 1601 cm-1 are also well identified in the decomposition, while in addition
the 1188 cm-1 band assigned to disorder in the graphitic lattice and the 1510 cm-1 band
revealing an amorphous component in the signal (Sadezky et al. 2005; Al -Jishi and
Dresselhaus 1982; Dippel and Heintzenberg 1999).
Finally the band intensity ratio ID/IG (0.54) gave an in-plane crystallite size (La), ranging
from 2 to 30 nm using two empirical formula given in literature (Knight and White 1989;
Cancado et al. 2006).
Figure 5-3 : Raman spectra of massive carbonaceous material, a raw signal & b decomposed Raman spectrum
showing 4 components (dotted lines) and fit (cross) after linear background correction.
1000 1200 1400 1600 1800
1188
1334
1510
1601
1000 1200 1400 1600 1800
Raman shift (cm-1)
G D
1338
1601
Spectrum decomposition
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
148
5.4.4. Transmission electron microscope study of the carbonaceous
material
In addition to RAMAN spectroscopy and XRD, TEM observed were performed in order to
obtain microstructural information. The general view in Figure 5-4a indicates that the
massive carbonaceous materials are in fact formed of carbon veil, best described as graphen
layers. In close association to it, nanometric crystals of size ranging from 5 to 50 nm are
disseminated in the carbonaceous material between the graphen layers. In addition, HRTEM
images (Figure 5-4b) confirm that the structure of the carbonaceous matrix is fully disordered
along the C axis.
Moreover, figure 5-4c & d reported an example of HRTEM image from nanoparticle and the
corresponding Fast Fourier Transform (FFT). The digital diffractogram from the particle
shows spots with fringe spacing of 3.1A and an angle of 70° between the two sets of fringes.
This experimental result agrees with the d{111} planes of the uraninite cubic structure. The
two other spots correspond to fringe spacing of 1.9A and 2.73 of the d{022} and d{002}
respectively showing that the zone axis of the particle is <110>. Lastly, the diffraction pattern
taken over a large area, Figure 5-4e& 5-4f suggests a preferential orientation of the {111}
plans of uraninite.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
149
Figure 5-4 : Transmission electron microscope image of MCM and associated nanocrystals; a, disseminated
nano crystals in the carbonaceous material, b, HRTEM images of nano crystals and amorphous carbonaceous
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
150
material matrix, c, lattice parameter of a euhedral crystal of uraninite, and d, corresponding FFT image, e & f
uraninite crystal in the carbon matrix and electron diffraction over the same area.
5.4.5. Isotopy & geochemistry
Bulk geochemistry gathered on massive and disseminated carbonaceous materiel is given in
the table 5-1. The massive material is almost entirely formed of carbon with more 66% C.
The Very little Si, Al, K, and Mg amounts are coherent with the absence of clay minerals
within the massive material. Nevetheless the material is particularly rich only in Cu and U
while other trace elements, especially those which are sensitive to redox condition like Mo,
Co, and V are negligible.
Table 5-1 : Chemistry and isotope composition of the two types of carbonaceous materials
Sample Massive CM Diffuse CM
SiO2 % 1.94 44.49
Al2O3 % 0.51 27.17
Fe2O3 % 3.44 0.66
K2O % 0.08 8.24
MgO % 0.06 2.06
TiO2 % 0.13 1.53
As (ppm) 139 36.67
Co (ppm) 142.1 31.18
Cu (ppm) 10020 167.9
Mo (ppm) 9.52 15970
Pb (ppm) 2192.82 234.52
U (ppm) 71910 403.6
V (ppm) 31.96 750.7
%C 66.3 0.04
%H 3.9 0.7
%S 4.68 0.5
δC °/00 -39.1 < detection limits
δS °/00 No data + 12.2
13C relative to PDB and 34S to CDT standards
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
151
5.5. Discussion
Considering the carbonaceous materials present at Kiggavik it appears that the petrographic
and textural relationships with alteration minerals lead us to integrate these materials to the
paragenesis formed during the hydrothermal alteration of the Archean basement and the
associated the transport and deposition of uranium. In Kiggavik as well as in the Athabasca
Basin (Sangély et al. 2007; Landais and Dereppe 1985; Leventhal et al. 1987; Alexandre and
Kyser 2006), the carbonaceous materials are considered to belong to succession of
hydrothermal events responsible for the main uranium deposition. Then, on the basis of this
multi-method characterization we propose to refine the interpretation of the Kiggavik
carbonaceous material in terms of genesis and potential role on uranium precipitation.
5.5.1. Forms of carbon and hydrothermal signatures
To sum-up the two main expressions of carbonaceous materials identified in alteration zone
associated with uranium ore depositions at Kiggavik are: (1) dissemination of short chain
carbon & sulfur compounds, the most common, and (2) more locally as massive, hard and
brittle aggregates or spherules of carbonaceous material. In both cases these carbonaceous
materials were compared with similar products formed by synthesis in laboratory. Then the
comparison of data from literature on experimental synthesis with those collected in natural
system may help to highlight the processes responsible for the genesis of carbonaceous
material and give complementary information to constrain the hydrothermal conditions in
unconformity related uranium deposits.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
152
5.5.2. Carbon sulfides a comparison between natural and laboratory created
hydrothermal systems
The first expression of carbonaceous material in the alteration system are the organic sulfur
compounds as short chain carbon sulfides which can be compared to the artificial synthesis of
the same chemical compounds, CS2 as well as thiols, from a FeS/HCl/CO2 or FeS/H2S/CO2
system at 75°C (Heinen and Lauwers 1996) via the 2 following reactions :
7FeS+ 8HCl +CO2 → 4FeCl2+3FeS2+CH3SH+2H2O and 2CH3SH +2H2O → CS2 +CO2+6H2
It also appears in the same study that DMDS and carbon disulfide are indicators of suboptimal
conditions for CO2 reduction, as consequence of a limitation of H2 resulting from an
unfavorable FeS/HCl (H2S) ratio or a low temperature. The formation of DMDS via the 2
methanthiol condensation in addition to short thiols may be significant of H2 limitation. It also
needs to be noted that such reaction produces pyrite. In all these reaction oxidation conditions
are controlled by mineral buffers, which are all present in the unaltered rock (pyrite &
magnetite) prior to alteration and given in (Shock 1990), while a part of H2 may be generated
from water radiolysis:
2 Fe3O4 + H2O = 3 Fe2O3 + H2 and 2 FeS + 4/3 H20 = FeS2 + 1/3 Fe304 + 4/3 H2
Finally thermodynamic studies on similar short chain carbon sulfides with the example of
dimethlysulfide gives another temperature constrain to the hydrothermal condition necessary
to the synthesis of such compounds, Figure 5-5 (Schulte 2010). Then when using the
measured or calculated fluid temperature for the brines involved in the alteration processes
(fluid inclusion and stable isotopes on illite) and ranging from 150 to 220°C at Kiggavik, but
similar to the one in the Athabasca Basins (Pagel and Ahamdach 1995; Kotzer and Kyser
1995; Pagel 1975; Renac et al. 2002), allows us to determine that the reaction is displaced in
the sens of synthesis of carbon sulfide compounds with a LogK just above 0 at 220°C but
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
153
around 8 at 150°C . Then the hydrothermal conditions related to alteration processes were
favorable for the in situ genesis of carbon sulfide compounds. It may also indicate that these
products were synthesized when temperature started to decrease possibly at the end of an
hydrothermal pulse.
Figure 5-5 : Stability of carbon sulfide coumpounds as a function of Log K and T °C, from
Schulte, 2010
Unfortunaly, the carbon content is too low in the disseminated material to get a carbon isotope
footprint of such compounds.
Then after look at the more volatile compounds the massive carbonaceous materials
5.5.3. Massive carbonaceous materials: solid properties & genesis
The massive carbonaceous materials found at Kiggavik presents similarities in term of
texture, petrographic relashionship with clays within alteration surrounding mineralization
zones as well as low 13C to the one identified as solid bitumen in the Paleoproetrozoic
Athabasca Basins in unconformity related uranium deposits (Leventhal et al. 1987; Sangély et
al. 2007). However the isotopic fractionation alone have been questioned as the efficient tool
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
154
to identified C fractionation from organic or inorganic processes, while only few literature
refers to the massive carbonaceous material (also named condensed CM) isotopic
fractionation experiments (Horita 2005). Nevertheless, the limited data avaliable quasi
systematic 13C depletion up to -60°/00 and ranging from -5 to – 50 °/00 have been measured on
MCM relatively to CO2 and CH4 between 200°C and 600°C in presence of metallic catalyst
such as Ni produced via FT type reaction (Lancet and Anders 1970; Horita 2001; Kerridge et
al. 1989; Sackett 1995).
As the with the carbon stable isotope fractionation, the solid properties and his structural
characterization have been poorly considered while been of great importance because of the
implications of the types of organic matter precursors, if there is any, in the formation of the
massive carbonaceous materials in hydrothermal environments, or the alteration or chemical
processes responsible for the transformation or neogenesis of such materials (Durand 1980).
5.5.4. Degree of tridimensional organization of massive carbonaceous
material
According to the XRD and RAMAN spectroscopy data the studied massive carbonaceous
materials cannot be called graphite. The lack of diffraction of X-ray indicates no sufficient
coherent carbon layer stacking along the c-axis (or a predominantly amorphous material). In
addition the RAMAN signal (ID/IG band intensity ratio, positions and shapes) share some
similarities with amorphous carbon, activated charcoal, graphite nano-particules or altered
graphite from uranium deposits (Tuinstra and Koenig 1970a; Chu and Li 2006; Wang et al.
1989; Calderon Moreno et al. 2000). The in plane crystallite size ranging between 2 to 30nm
and the images in TEM both indicate that the material is predominantly formed of sp2 bonded
(graphene) carbon mono layers or at best a few layer of graphene with a low degree of spatial
organization. This is also marked by the broad D and G bands in the RAMAN spectra, with an
amorphous component in the signal around 1500cm-1, while the D band at 1350cm-1 signs the
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
155
graphen layer edges of a disordered graphitic lattice as the interpreted band positions from
spectrum decomposition (Sadezky et al. 2005).
Then if it is not graphite, the origin of such material and the formation processes can be
questioned. In fact graphite resulting for the thermal maturation of organic matter is known to
keep the acquired crystalline order (Luque et al. 1993). Then the low level of order of the
massive carbonaceous material relatively to the regional greenschist to amphibolites
metamorphic facies together with his only presence in the alteration halos seems in favor of a
thermal event and formation processes unrelated with the prograde metamorphism (Pasteris
and Wopenka 1991; Wopenka and Pasteris 1993; Lewry and Sibbald 1980). The hypothesis
of fluid deposited during ore related hydrothermal activity might be given by
crystallochemical properties via the RAMAN signature. From this perspective the massive
carbonaceous from Kiggavik share more similarities with the Neoproterozoic, vein hosted,
brittle solid bitumens or graphitoids described in hydrothermal environments related to
Klecany intrusive complex in Bohemia (Jehlička et al. β003) and also quite similar to shungite
found in Karelia (La of 40 nm; disorder) (Jehlička et al. β005; Wopenka and Pasteris 1993) or
to laboratory produced, fluid deposited graphite (Luque et al. 1998), rather than graphitized
carbonaceous material under greenschist facies or even more to graphite host in higher
metamorphic grade facies (Wopenka and Pasteris 1993). Then all low temperature (< 250°C)
hydrothermally deposited carbonaceous or graphitic material appears to share a small in-plan
crystallite size as well as a high level of disorder.
In addition during experimental precipitation of graphite in a C-H-O system, parameters as
such as lower temperature, and higher fH2 lead to the formation of a poorly organize material
(Pasteris and Chou 1998; Ziegenbein and Johannes 1990; Mastalerz et al. 1995). Moreover,
both nucleation and crystal growth must occur to produce graphite. Finally in unconformity
related uranium deposits system such as Kiggavik the presence of CO2 and H2 have been
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
156
demonstrated and thought to be produce by water radiolysis (Derome 2002; Dubessy et al.
1988).
5.5.5. Nanoscale graphite and possible implications for uranium
precipitation
Graphite is known as chemically inert and though is role as been debated as a potential
control for uranium mineralization in the Eastern and Western Athabasca Basins and in the
SW Thelon at Boomerang where major deposits are spatially related with regional scale
graphitic fault systems (Davidson and Gandhi 1989; Thomas and Wood 2007; Laverret et al.
2006; Thomas et al. 2000). By contrast with the massive carbonaceous materials studied here,
in these structures, graphite doesn’t show a low level of organization and belong to the
metamorphic history of a metasedimentary rock package which underwent at least a green
schist metamorphic grade (Lewry and Sibbald 1980). In contrast no such graphitic bearing
fault is present at Kiggavik, and the only potential sources of organic compounds are to be
related to black shales recognize at minima 10 km to the East.
In addition a nano-scale association has been identified with the MCM and mint crystals of
uraninite and pyrite. Moreover Cu and U are both elevated in the carbonaceous matrix even if
no mineral phase can be identified with the SEM. But nano crystal of uranium phases seems
to coexist within the carbonaceous material. Such close association between the
carbonaceous material and uraninite could be related to orientation-controlled growth on the
graphene layer. In fact, the epitaxial growth of uraninite would be due to the match between
uraninite lattice, on the {111} plan, and the (0001) hexagonal lattice of graphen.
Then the deposition of the carbonaceous material may be contemporanous to the uraninite
deposition during the ore forming processes (both needing reducing condition to precipitate).
In such a process, the enhanced surface area of the carbonaceous material can act as a
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
157
potential site for nucleation or uraninite and chalcopyrite. Such process would be adequate to
explain the disseminated low grade mineralization found widely in alteration zones where
carbonaceous materials are present.
5.6. Conclusion
Then regarding the petrography, the isotopic measurement and the crystallographic properties,
we propose that the carbonaceous material in Kiggavik could be the expression of abiotic,
hydrothermal synthesis of carbonaceous compounds, with small chains of carbon sulfide and
also massive carbon. This is supported by laboratory experiments of hydrocarbon synthesis
via the CO2 or CH4 reduction on mineral catalyzes like magnetite or pyrite (Heinen and
Lauwers 1996). In addition the range of temperature used for the synthesis of short chains of
carbon sulfides are similar to the one estimated via fluid inclusion work in unconformity type
uranium deposits around 200°C, (see chapter 3) (Pagel 1975; Derome et al. 2005).
We also suggest that the solid properties may provide a favorable environment for uranium
minerals, and metallic sulfide precipitation.
Acknowledgments:
Authors would like to express their gratitude to Marie-France Beaufort for the HRTEM
charaterisation and to AREVA NC & ERM sponsors of this study.
5.7. References
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
158
Al-Jishi R, Dresselhaus G (1982) Lattice-dynamical model for graphite. Physical Review B 26:4514-4522.
Alexandre P, Kyser TK (2006) GEOCHEMISTRY OF URANIFEROUS BITUMEN IN THE SOUTHWEST ATHABASCA BASIN, SASKATCHEWAN, CANADA. Economic Geology 101:1605-1612. doi: 10.2113/gsecongeo.101.8.1605.
Beaufort D, Patrier P, Laverret E, Bruneton P, Mondy J (2005) Clay Alteration Associated with Proterozoic Unconformity-Type Uranium Deposits
in the East Alligator Rivers Uranium Field, Northern Territory, Australia. Economic Geology v. 100:pp. 515–536.
Calderon Moreno JM, Swamy SS, Fujino T, Yoshimura M (2000) Carbon nanocells and nanotubes grown in hydrothermal fluids. Chemical Physics Letters 329:317-322. doi: http://dx.doi.org/10.1016/S0009-2614(00)01017-4.
Cancado LG, Takai K, Enoki T, Endo M, Kim YA, Mizusaki H, Jorio A, Coelho LN, Magalhaes-Paniago R, Pimenta MA (2006) General equation for the determination of the crystallite size L[sub a] of nanographite by Raman spectroscopy. Applied Physics Letters 88:163106.
Chu PK, Li L (2006) Characterization of amorphous and nanocrystalline carbon films. Materials Chemistry and Physics 96:253-277. doi: http://dx.doi.org/10.1016/j.matchemphys.2005.07.048.
Curiale JA (1986) Origin of solid bitumens, with emphasis on biological markers results. Organic Geochemistry 10:559-580.
Davidson GI, Gandhi SS (1989) Unconformity-related U-Au mineralization in the middle Proterozoic Thelon sandstones, Boomerang Lake Prospect, Northwest Territories,Canada. Economic Geology 84:143-157.
Derome D (2002) Evolution et origines des saumures dans les bassins protérozoiques au voisinage de la discordance socle/couverture. L'exemple de l'environnement des gisements d'uranium associés aux bassins Kombogie (Australie) et Athabasca (Canada). Université Henri Poincaré, Nancy.
Derome D, Cathelineau M, Cuney M, Fabre C, Lhomme T, Banks DA (2005) Mixing of Sodic and Calcic Brines and Uranium Deposition at McArthur River, Saskatchewan, Canada: A Raman and Laser-Induced Breakdown Spectroscopic Study of Fluid Inclusions. Economic Geology 100:1529-1545. doi: 10.2113/gsecongeo.100.8.1529.
Dippel B, Heintzenberg J (1999) Soot characterization in atmospheric particles from different sources by NIR FT Raman spectroscopy. Journal of Aerosol Science 30, Supplement 1:S907-S908. doi: http://dx.doi.org/10.1016/S0021-8502(99)80464-9.
Dubessy J, Pagel M, Beny JM, Christensen B, Hickel C, Kosztolany B, Poty B (1988) Radiolysis evidenced by H2-O2 and H2 bearing fluid inclusions in three uranium deposits. Geochimica et Cosmochimica Acta 52:1155-1167.
Durand B (1980) Kerogen: Insoluble organic matter from sedimentary rocks. Techniq., Paris. Farkas A (1984) Mineralogy and host rock alteration of the Lone Gull deposit Internal report.
Urangesellschaft, Frankfurt am Main, pp 45. Foustoukos DI, Seyfried WE (2004) Hydrocarbons in Hydrothermal Vent Fluids: The Role of
Chromium-Bearing Catalysts. Science 304:1002-1005. doi: 10.1126/science.1096033. Gauthier-Lafaye F, Weber F (1989) The Francevillian (Lower Proterozoic) uranium ore
deposits of Gabon. Economic Geology 84:2267-2285. Gize AP (1999) Organic alteration in hydrothermal sulfide ore deposits. Economic Geology
94:967-979. doi: 10.2113/gsecongeo.94.7.967.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
159
Heinen W, Lauwers A (1996) Organic sulfur compounds resulting from the interaction of iron sulfide, hydrogen sulfide and carbon dioxide in an anaerobic aqueous environment. Origins Life Evol Biosphere 26:131-150. doi: 10.1007/bf01809852.
Hoeve J, Sibbald TII (1978) On the genesis of the Rabbit Lake and other unconformity-type uranium deposits in Northern Saskatchewan, Canada. Economic Geology 73.
Hoeve J, Sibbald TII, Ramaekers P, Lewry JF (1980) Athabasca basin unconformity-type uranium deposits : a special class of sandstone-type deposits? In: Ferguson J, Goleby AB (eds) Uranium in the Pine Creek Geosyncline. International Atomic Energy Agency, Vienna, pp pp. 575-594.
Hoeve J, Quirt D (1984) Mineralization and host rock alteration in relation to clay mineral diagenesis and evolution of the Middle-Proterozoic Athabasca basin, Northern Saskatchewan, Canada Saskatchewan Research Concil Technical report. Saskatchewan Reasearch Council, pp 197.
Horita J (2001) Carbon isotope exchange in the system CO2-CH4 at elevated temperatures. Geochimica et Cosmochimica Acta 65:1907-1919.
Horita J (2005) Some perspectives on isotope biosignatures for early life. Chemical Geology 218:171-186. doi: http://dx.doi.org/10.1016/j.chemgeo.2005.01.017.
Jehlička J, U a O, Poko ý J Ra a spe t os opy of a o a d solid itu e s i sedimentary and metamorphic rocks. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy 59:2341-2352. doi: http://dx.doi.org/10.1016/S1386-1425(03)00077-5.
Jehlička J, F a k O, Poko ý J, Rouzaud J-N (2005) Evaluation of Raman spectroscopy to detect fullerenes in geological materials. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy 61:2364-2367. doi: http://dx.doi.org/10.1016/j.saa.2005.02.014.
Kerridge JF, Mariner R, Flores J, Chang S (1989) Isotopic characteristics of simulated meteoritic organic matter. Origins Life Evol Biosphere 19:561-572.
Knight DS, White WB (1989) Characterization of diamond films by Raman spectroscopy. Journal of Material Research 4:385-393.
Kotzer TG, Kyser TK (1995) Petrogenesis of the Proterozoic Athabasca Basin, northern Saskatchewan, Canada, and its relation to diagenesis, hydrothermal uranium mineralization and paleohydrogeology. Chemical Geology 120:45-89. doi: http://dx.doi.org/10.1016/0009-2541(94)00114-N.
Kyser K, Wilson MR, Ruhrmann G (1989) Stable isotpoe contraints on the role of graphite in the genesis of unconformity-type uranium deposits. Canadian Journal of Earth Sciences 26:490-498.
Lancet MS, Anders E (1970) Carbon isotops fractionation in the Fischer-Tropsch synthesis and in meteorites. Science 170:980-982.
Landais P, Dereppe JM (1985) A chemical study of the carbonaceous material form the Carswell structure - The Carswell Structure Uranium deposits Geolgical Association of Canada SPecial Paper. Toronto, pp 165-174.
Laverret E, PATRIER P, BEAUFORT D, Kister P, Quirt D, BRUNETON P, Clauer N (2006) Mineralogy and geochemistry of the host-rock alterations associated with the Shea Creek unconformity-type uranium deposits (Athabasca basin, Saskatchewan, Canada) Part1. Spatial variation of illite properties. Clays and Clay Minerals 54:275-294.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
160
Leventhal JS, Grauch RI, Threlkeld CN, Lichte FE, Harper CT (1987) Unusual organic matter associated with uranium from the Claude Deposit, Cluff Lake, Canada. Economic Geology 82:1169-1176. doi: 10.2113/gsecongeo.82.5.1169.
Lewry JF, Sibbald TII (1980) Thermotectonic evolution of the Chruchill province in Northern Saskatchewan. Tectonophysics 68:45-82.
Luque FJ, Barrenechea JF, Rodas M (1993) Graphite geothermometry in low and high temperature regimes: two case studies. Geological Magazine 130:501-511. doi: doi:10.1017/S0016756800020562.
Luque FJ, Pasteris JD, Wopenka B, Rodas M, Barrenechea JF (1998) Natural fluid-deposited graphite; mineralogical characteristics and mechanisms of formation. American Journal of Science 298:471-498. doi: 10.2475/ajs.298.6.471.
Mastalerz M, Bustin RM, Sinclair AJ, Stankiewicz BA (1995) Carbon-rich material in the Erickson hydrothermal system, northern British Columbia, Canada; origin and formation mechanisms. Economic Geology 90:938-947. doi: 10.2113/gsecongeo.90.4.938.
McCollom TM, Seewald JS (2006) Carbon isotope composition of organic compounds produced by abiotic synthesis under hydrothermal conditions. Earth and Planetary Science Letters 243:74-84. doi: http://dx.doi.org/10.1016/j.epsl.2006.01.027.
M Collo TM La o ato y Si ulatio s of A ioti Hyd o a o Fo atio i Ea th’s Deep Subsurface. Reviews in Mineralogy and Geochemistry 75:467-494. doi: 10.2138/rmg.2013.75.15.
Miller AR, LeCheminant AN (1985) Geology and uranium metallogeny of Proterozoic supracrustal successions, central District of Keewatin, N.W.T with comparisons to northern Saskatchewan Geology of uranium deposits. Canadian Institute of Mining and Metalurgy, pp 167-185.
Nagy B, Gauthier-Lafaye F, Holliger P, Davis DW, Mossman DJ, Leventhal JS, Rigali MJ, Parnell J (1991) Role of organic matter in containment of uranium and fissiongenic isotopes at the Oklo natural reactor. Nature 354:472-475.
Pagel M (1975) Détermination des conditions physico-chimique de la silicification diagénétique des grès Athabasca (Canada) au moyen des inclusions fluides. Comptes Rendus de l'académie des Sciences Paris 280:2301-2304.
Pagel M, Poty B, Sheppard SMF (1980) Contribution to some Saskatchewan uranium deposits from fluid inclusion and isotopic data In: Ferguson J, Goleby AB (eds) Uranium in the Pince Creek geosyncline. AEIA, Vienna, pp 639-654.
Pagel M, Ahamdach N (1995) Etude des inclusions fluides dans les quartz des gisements d'uranium de l'Athabasca et du Thelon (Canada). Centre de Recherche sur la Geologie des matières premieres minerales et énérgétiques - CREGU, Vandoeuvre les Nancy, pp 1-10.
Pasteris JD, Wopenka B (1991) Raman spectra of graphite as indicators of degree of metamorphism. The Canadian Mineralogist 29:1-9.
Pasteris JD, Chou IM (1998) Fluid-Deposited Graphitic Inclusions in Quartz: Comparison Between KTB (German Continental Deep-Drilling) Core Samples and Artificially Reequilibrated Natural Inclusions. Geochimica et Cosmochimica Acta 62:109-122. doi: http://dx.doi.org/10.1016/S0016-7037(97)00322-0.
Polito PA, KYSER TK, Marlatt J, Alexandre P, Bajwah Z, Drever G (2004) Significance of Alteration Assemblages for the Origin andEvolution of the Proterozoic Nabarlek
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
161
Unconformity-Related Uranium Deposit,Northern Territory, Australia. Economic Geology 99:113-139. doi: 10.2113/gsecongeo.99.1.113.
Renac C, Kyser K, Durocher K, Dreaver G, O'Connor T (2002) Comparison of diagenetic fluids in the Proterozoic Thelon and Athabsca Basins, Canada: implications for protracted fluid histories in stable intracratonic basins. Can J Earth Sci 39:113-132.
Sackett WM (1995) The thermal stability of methane from 600-1000°C. Organic Geochemistry 23:403-405.
Sadezky A, Muckenhuber H, Grothe H, Niessner R, Pöschl U (2005) Raman microspectroscopy of soot and related carbonaceous materials: Spectral analysis and structural information. Carbon 43:1731-1742. doi: http://dx.doi.org/10.1016/j.carbon.2005.02.018.
Sangély L, Chaussidon M, Michels R, Brouand M, Cuney M, Huault V, Landais P (2007) Micrometer scale carbon isotopic study of bitumen associated with Athabasca uranium deposits: Constraints on the genetic relationship with petroleum source-rocks and the abiogenic origin hypothesis. Earth and Planetary Science Letters 258:378-396. doi: http://dx.doi.org/10.1016/j.epsl.2007.03.018.
Schulte M (2010) Organic Sulfides in Hydrothermal Solution: Standard Partial Molal Properties and Role in Organic Geochemistry of Hydrothermal Environments. Aquat Geochem 16:621-637. doi: 10.1007/s10498-010-9102-3.
Shock E (1990) Geochemical constraints on the origin of organic compounds in hydrothermal systems. Origins Life Evol Biosphere 20:331-367. doi: 10.1007/bf01808115.
Thomas DJ, Matthews RB, Sopuck V (2000) Athabasca Basin (Canada) unconformity-type uranium deposits: exploration model, current mine developpments and exploration directions In: Cluer JK, Price JG, Struhsacker EM, Hardyman RF, Morris CL (eds) Geology and Ore Deposits 2000:The Great Basin and Beyond, Geological Society of Nevada symposium proceedings. Reno, NV, pp 103-126.
Thomas MD, Wood G (2007) Geological significance of gravity anomalies in the area of McArthur River uranium deposit, Athabasca Basins, Saskatchewan In: Jefferson CW, Delaney G (eds) EXTECH IV: Geology and Uranium Exploration TECHnology of the Proterozoic Athabasca Basin, Saskatchewan and Alberta Geological Survey of Canada.
Tuinstra F, Koenig JL (1970a) Raman Spectrum of Graphite. The Journal of Chemical Physics 53:1126-1130.
Tuinstra F, Koenig JL (1970b) Characterization of Graphite Fiber Surfaces with Raman Spectroscopy. Journal of Composite Materials 4:492-499. doi: 10.1177/002199837000400405.
Ueno Y, Yoshioka H, Maruyama S, isozaki Y (2004) Carbon isotopes and petrography of kerogens in 3.5-Ga hydrothermal silica dikes in the North Pole area, Western Australia. Geochimica et Cosmochimica Acta 68:573-589.
Walenta K (1974) On Studtite and its composition. American Mineralogist 59:166-171. Wang A, Dhamenincourt P, Dubessy J, Guerard D, Landais P, Lelaurain M (1989)
Characterization of graphite alteration in an uranium deposit by micro-Raman spectroscopy, X-ray diffraction, transmission electron microscopy and scanning electron microscopy. Carbon 27:209-218. doi: http://dx.doi.org/10.1016/0008-6223(89)90125-5.
Wilson MR, Stasiuk LD, Fowler MG (2002) Post mineralization origin of organic matter in Athabasca unconformity-type uranium deposits, Saskatchewan, Canada Summary of Investigations. Saskachewan Geological Survey pp 6.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
162
Wopenka B, Pasteris JD (1993) Structural characterization of kerogens to granulite-facies graphite; applicability of Raman microprobe spectroscopy. American Mineralogist 78:533-557.
Yeo G, Potter EG (2010) Review of reducing mechanisms potentially involved in the formation of unconformity-type uranium depoists and their relevance to exploration In: Survey SG (ed). Sask. Ministry of Energy and Resources, pp 13.
Ziegenbein D, Johannes W (1990) Graphite-Fluid-Wechselwirkungen: Einfluss der Graphitkristallinität In: Emmermann R, Giese P (eds) KTB report. Niedersächsisches Landesamt Bodenforsch, pp 559.
Carbonaceous material occurrence in the Kiggavik uranium deposits (Thelon, Nunavut, Canada).
163
B. L ES MARQUEURS MINÉRALOGIQUES
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
164
1. Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
Riegler, Thomas; Quirt, Dave & Daniel Beaufort
In preparation for submission in Mineralium Deposita
1.1. Abstract
The Kiggavik Andrew lake structural trend consists in four mineralized zones, partially
outcropping, lying two kilometers south of the erosional contact with the unmetamorphosed
sandstone and basal conglomerates of the Paleoproterozoic Thelon Formation. The
mineralization is controlled by a major East-West fault system associated with illite and
sudoite alteration halos developed in the Archean metagraywackes of the Woodburn Lake
Group. Aluminum phosphate sulfate minerals (APS) from the alunite group crystallized in
association with the clay minerals in the basement alteration halo as well as in the overlying
sandstones which suffered mostly diagenesis. APS minerals are Sr and S-rich (svanbergite
end-member) in the sedimentary cover overlying the unconformity while they are LREE-rich
(florencite end member) in the altered basement rocks below the unconformity. The
geochemical signature of each group of APS mineral together with the petrography indicates
two distinct generations of APS minerals:(1) a first one related to sedimentation-diagenesis
processes at the bottom of the Thelon sandstones and (2) a second one related to hydrothermal
alteration processes which accompanied the uranium deposition in the basement and partially
overlap the sedimentary-diagenetic mineral parageneses . The primary REE bearing minerals
of the hosts rock were characterized in order to identify the potential sources of REE. The
obtained chemical composition of REE highlights a local re-incorporation of the REE
released from the alteration processes in the APS minerals. The distinctive geochemical
signatures between diagenetic (or sedimentary) and hydrothermal APS minerals suggest a
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
165
different source material in the Thelon basin than the Athabasca basin. Lastly as some of the
primary REE-bearing minerals are potential uranium sources, the potential fertility and the
sources of the uranium can be questioned.
1.2. Introduction
Since several decades hydrated aluminum phosphate and sulfate (APS) minerals of the alunite
supergroup have been found and studied in a broad range of geological environments; form
soils to sedimentary basins, or hydrothermal and volcanic system (Dill, 2001; Stoffregen and
Alpers, 1987). They occur as minute, euhedral crystal with rhombohedral or pseudocubic
habits. Their general structural formula is AB3 (XO4)(OH)6, where A, B, X are the 12, 6 and
4-fold coordinated crystallographic sites. The A site can be occupied by monovalent (H3O+,
K+, Na+, Rb+, NH4+, Ag+, Tl+, etc), divalent (Ca2+, Sr2+, Ba2+, Pb2+) or trivalent (Bi3+,
LREE3+) cations. More rarely tetravalent cation like Th4+ can integrate the APS crystal
structure in this site. The B: 6-fold coordinence site is occupied by Al3+ and Fe3+, and lastly
the X site is commonly occupied by S6+, P5+, and As5+. As the three sites are subject to
numerous substitutions, and thus to complex solid solutions, these crystal-chemical properties
give rise to tens of end-members within the alunite supergroup.
Despite their relative very low abundance as well as their very small size making them
somehow difficult to identify in thin sections, recent studies have highlighted the potential of
APS mineral as geochemical markers of the proximity of orebodies in unconformity related
uranium deposits (Gaboreau et al., 2005; Gaboreau et al., 2007). In fact, two major
characteristics can be pointed out: (1) once formed, they resist to most of the chemical
reactions involved during surface or subsurface alteration processes and (2) their sensitivity to
physic-chemical condition of formation (such as Eh and pH) is recorded in their broad range
of chemical composition, with the ability to trap and concentrate trace elements and
particularly the light rare earth elements (LREE), (Herold, 1987; Stoffregen, 1993).
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
166
Worldwide in the paleoproterozoic unconformity related uranium deposits, APS minerals
seem to be systematically associated with the clay alteration assemblages. They have been
studied in the Kombolgie basin in Australia (Beaufort et al., 2005; Gaboreau et al., 2005) as
well as in the Athabasca and Kombolgie Basins (Gaboreau et al., 2007; (Cloutier et al. 2010)
and both the Thelon and Horny Bay Basins in Canada (Gall and Donaldson, 2006) as well as
in the underlying saprolites (Miller 1983).
The spatial distribution and the compositional variation of these minerals around the uranium
orebodies led some authors to consider them as good indicator of both the redox and pH
paleo-conditions responsible for the development of fronts during the alteration process, and
hence as potential tools for mineral exploration (Gaboreau et al., 2005, 2007).
The aim of this study is to determine the nature and the origin of the APS minerals present
near the bottom of the middle Proterozoic Thelon sandstone formation and in the underlying
archean basement rocks which host the alteration halos of the uranium ore bodies distributed
along the Kiggavik Andrew lake structural trend, Nunavut, Canada . The main goals are (1) to
determine the paragenetic association and the crystal chemistry of APS mineral in the
basement and the overlying Thelon sandstones, (2) to determine the source material for APS
minerals and (3) assign and replace each paragenesis in the basin and the uranium
mineralization history. These results are compared and discussed with respect to those
already obtained from APS in alteration halos associated with the unconformity-type uranium
deposits of the both Australian and Canadian counterparts.
1.3. Regional geological setting
The Kiggavik exploration project is composed of two groups of claims, St Tropez to the
North and Kiggavik down South, going roughly from the Southern Shore of Schultz Lake to
the East of Judge Sisson Lake, about 80km West of the Inuit hamlet of Baker Lake, NU. All
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
167
the deposits, Kiggavik, End and Andrew, and most of the prospects Bong, Granite, Sleek, are
exclusively located in the Kiggavik part of the project, figure 1-1. The overall historical metal
content is estimated to about 50 000t U, with an average 0.5% grade (Jefferson et al., 2007).
Figure 1-1 : Bedrock geology of the NE Thelon Basin margin, modified form Jefferson et al., 2013. Sampling
area are indicated by the following number: 1 Granite Grid area; 2 W94-4 drillhole south of the Judge Sisson
Fault, W2 drillhole; 4 Uno Granite
The study area encompasses the St Tropez and the Kiggavik areas in order to have a more
regional, vision of the geological factors that could be involved to generate a favorable
environment for uranium mineral deposition (basement rocks lithology, structural control of
the fluid flow paths, degree of fluid rock interaction in any place etc.).
4
2
3
1
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
168
The host of the mineralization is the Woodburn Lake Group (WLG), a 2.6-2.7 Ga, neoarchean
supracrustal rock package formed mainly by a sequence of metagraywackes and
metavolcanics, with minor quartzite and iron formation. This sedimentary pile
retromorphosed in a greenschite facies overlies older granitic gneiss of uncertain age and is
part of a series of greenstone belt known from Northern Saskatchewan to Northern Baffin
Island, set during the Rae craton continental riflting (Hartlaub et al., 2004). The archean rock
package had his own tectonometamorphic history. During the paleoproterozoic the archean
and the overlying paleoproterozoic cover where imbricated and structured together in several
stages of deformation related to the Thelon-Taltson (2.0-1.9 Ga) and the Trans-Hudson (2.0-
1.8 Ga) orogens, respectively at the NW and SE during the Laurentia accretion (Hoffman,
1990). These events formed the main structural frame with main foliations and major shield
scale ductile mylonite zones and led to a complex stratigraphic stack not yet completely
understood (Pehrsson et al., 2010). Following the Thelon-Taltson orogeny collapse two major
suites of igneous bodies took place. The older intrusive (1.82-1.85 Ga) belongs to the Hudson
Suite; composed of granite; Martell syenite and the Dubawnt minettes. It was followed
100Ma later by the Nueltin rapakivi granite and its volcanic equivalent, the Pitz rhyolites
which belongs to the Wharton Group which constitute the intermediate and second sequence
of the Dubawnt supergroup (Miller and LeCheminant, 1985; Peterson et al., 2002; Rainbird et
al., 2003). The last sequence is the Barrensland Group which hold the Thelon Formation, a
siliciclastic sedimentary sequence similar the Athabasca Group in term of age and lithology.
As already mentioned in the Athasbasca basin, the upper part the Thelon sandstone have been
locally cemented by apatite during an early diagenesis stage dated between 1720 and 1647
Ma (Miller et al., 1989). Morever in addition to the fluor-apatite cement observed in the
Thelon and the Hornby bay basins, APS cements have been also described in the Thelon
Formation, (Gall and Donaldson, 2006).
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
169
In addition to those already observed in the sandstones, APS minerals where commonly
observed in close association with illite and sudoite (Al-Mg chlorite) within the clay alteration
halos which envelop the uranium deposits along the Kiggavik - Andrew lake structural trend
(Riegler et al. 2013).
1.4. Sampling and methods
A set of several tens of fresh and altered rocks samples from drillcores and outcrops coming
from various locations in the Kiggavik and St Tropez area were selected for a preliminary
petrographic analysis. Such a sampling encompasses the basement rocks with the
metagraywackes and the later intrusive (Hudson Granite and aplite, Martell Syenite, Nueltin
porphyritic rhylolite) as well as the overlying basal sedimentary beds of the Thelon Basin -
conglomerates and conglomeratic sandstones) figure 1-1, Table 1-1. 13 samples were then
selected within the previous extensive set of samples for a detailed analysis of APS minerals
in altered rocks and their parental minerals in the fresh ones. In addition the chemical
compositions of 189 core samples and 50 centimeter long composite samples of altered and
fresh metagraywackes were acquired to investigate the elements transfers, Table 1-1. These
samples are representative of the varying degree of alteration in the alteration halos developed
around the major structures which controlled the deposition of uranium orebodies.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
170
Table 1-1: Kiggavik-St Tropez APS, REE minerals bearing rocks sampling table
Geochemistry
Sample name Area Drillhole/Outcrop rock type alteration Umin ICP-OES
ICP-MS
Thelon Formation: Sedimentary Cover
GG3a Granite Grid outcrop mudstone no no 1 GG3b,c, GG4, 5, 7,
StTropez " outcrop sandstone no " 6
Basment
GGG Granite Grid outcrop Hudson granite no no
W2-2 Sleek Lake drillhole " no "
W2-03 " " metagraywacke no " 1
SL9_1 to 5 " " Hudson granite yes " 5
UnoGranite St Tropez outcrop " no "
W97-4_10 & 17 Judge
Sisson lake drillhole " no " 1
W97-4_3 " " metagraywacke no "
B1-94-1_08 " " " no " 1
ALCS Andrew
Lake outcrop porphyritic
ryholite no " 1
BSE_05 Bong drillhole metagraywacke no " 1
BG45_13 " " " no " 1
BG42-23 " " metagraywacke yes yes
BG42-21a, b; 25; 30; 40 " " " yes no 5
BG45_28 " " " yes yes 1
BG43_028 " " " yes " 1 BG42 composite
set " " " yes " 133 BG49 composite
set " " " no no 34
Then, for the Sedimentary cover (Thelon Formation): Unaltered mudstones: GG3a as well as
unaltered sandstones GG3b, c; GG4 & GG7 samples have been taken on outcrop along the
Thelon fault North of the Granite Grid prospect, point #1 on the figure 1-2. The GG4 & 7
sampled were taken a few kilometers away to the East. In the basement rocks the main sample
location were:
- Altered and/or mineralized metagraywacke form the Bong prospect with the BG42
and BG49 drillholes (DDH)
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
171
- Unaltered Intrusives: A prophyritic ryholite dyke belonging to the Nueltin Suite
located at the Andrew Lake core storage (ALCS). Hudson granite, part of the Schultz
lake intrusive complex with the W97-4_10 & W2-2 drillholes as well as an outcrop
sample form the Granite Grid and the NE St Tropez areas, respectively the point #2, 3
and 4 on the figure 1-1.
- Altered Hudson granite form the Sleek Lake area SL9_01 distal to mineralization &
SL9_05 in the vicinity of very local and weak mineralization intercepts. Such samples
are representative of barren alteration zones.
1.4.1. Methods
Petrographic study and mineralogical identification were made in thin sections using
observation with a polarizing optical microscope and a scanning electron microscope (SEM,
JEOL 5600LV) equipped with a Brucker Energy Dispersive Spectrometer (EDS) X-ray
analyser at the University of Poitiers (15kV acceleration voltage, 1 nA beam current).
Quantitative chemical analyses were performed using a Cameca SX100 electron microprobe
with wavelength dispersion spectrometers (WDS) at the CAMPARIS micro-analysis facility,
UPMC Jussieu Paris. Chemical microanalysis of Si, Al, Fe, F, P, S, Ca, Ba, Sr, La, Ce, Pr,
Nd, Th and U were obtained at the following analytical conditions: 15kV accelerating
voltage, 4 nA beam current, 2 micrometer spotsize and a counting time ranging from 5 to 20
seconds according to the specific element. The microprobe was calibrated using both natural
and synthetic standards: anorthite, apatite, pyrite, diopside, barite, uraninite, thorite, monazite,
SrSiO3, NdCu and a glass doped in rare earth elements (REE). The relative error on the
elements is below 1 %. The structural formulas of APS minerals were calculated using a 6
cations normalization as in the theoretical mineral formula AB3 (XO4)2(OH)6.
Bulk rock chemistry (including major and 54 traces elements) of representative samples
selected in our study were done using ICP-MS at the Service d'Analyse des Roches et des
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
172
Mineraux - CNRS – CRPG, in Nancy France. These chemical data have been completed by
an exploration chemical data set provided by AREVA Resources Canada (major and traces
elements) analysed at the Saskatchewan Research Council Laboratory in Saskatoon, Canada
using ICP-OES. Due to the lower detection limits and better accuracy provided by ICP-MS,
only the samples analyzed at the SARM will be used to compare the trace elements.
In order to decipher and interpret the geochemical data gathered on the REE bearing phases
we carried a petrographic study to highlight the textural and chronological relationships of
these minerals. Thus the primary, magmatic or sedimentary/diagenetic paragenesis have to be
identified and compared with secondary mineral assemblage linked to the hydrothermal
events in relation with the mineralization processes.
1.5. APS minerals and alteration petrography
In thin sections APS were observed by SEM because of their brightness in backscattered
electron (BSE) mode, due to their high content in heavy elements such as Sr and LREE.
Generally, APS crystals occur as very small euhedral rhombs (2–10 mm in average width,
exceptionally up to 50mm) located in the intergranular porosity of the clay matrix which
constitutes most of the alteration products of both sedimentary and basement rocks or are
associated with secondary quartz and hematite as fracture controlled cement. Locally coarser
grained APS crystals display features of growth zoning characterized by alternation of
concentric bright and light grey thin zones.
Their identification is quite arduous in optical microscopy due to their small size and the
possible confusion with apatite and their relatively scattered distribution in the rock even if
they can form massive aggregate in places (figure 1-2a).
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
173
Figure 1-2 : Aluminum phosphate sulfate minerals (APS) of the Kiggavik area in Thelon Formation ( pictures A
to D) and in the altered basement (E& F). A APS minerals in the sandstone in equilibrium with kaolinite,
remanante porosity filled by microcrystalline quartz (QTZ3) GG7 sample; B Massive APS cement; C
Microcrystalline (QTZ3) and APS minerals fracture cross cutting unaltered red mudstone at the base of the
Thelon Fm, later re-opened and filled with illite and hematite, GG3a sample; D Local ililtization pocket
developed in a large kaolinite booklet with co precipitation of APS, GG4 sample; E Altered granite with Illite
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
174
replacement of feldspar and devellopement of APS minerals, SL9 drillhole, Sleek lake area; F Illitic pocked with
euhedral APS, Andrew Lake, And10-01 drillhole
Abbreviations, Ill: illite; Hm: Hematite; Kao: kaolinite; Qtz: quartz
1.5.1. APS of the basal Thelon Formation
In the sandstones APS (hereafter named and labeled by the number of each generation)
minerals are relatively abundant in the following petrographic settings: (1) as pore filling
aggregates of very fine crystals with a typical pseudocubic habits or as cements (Figure 1-2a
& 2b); (2) as disseminated euhedral crystals coeval of post diagenetic quartz overgrowths
figure 2c and (3) locally associated with illite flakes in the late illitization pockets developed
at the expense of the pore-filling kaolinite, figure 1-2d.
Late reopening the post diagenetic quartz hydraulic breccia is associated with co-precipitation
of illite and anatase followed by specular hematite. The paragenetic sequence determined in
the sandstone is presented figure 1-3.
Figure 1-3 : Mineral paragenesis of APS minerals in the basal Thelon Formation
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
175
According to the petrographic study, the first generation (APS1) is related to a sedimentary-
diagenetic stage which emcompasses the deposition of large sedimentary kaolinite booklets
and then their diagenetic recystallization into dickite ± hematite with increasing burial depth,
contemporaneously of the formation of diagenetic quartz overgrowths (QTZ2). In addition,
these APS1 are associated with a AlO(OH), cerianite, Ce-La oxides, thorianite and hematite
paragenesis in the GG7 sample, figure 1-4. The second generation (APS2) is trapped in a very
fine grained, microcrystalline, quartz filling the remaining porosity. This quartz cementation
heals microbreccia and fractures which affected lithic fragements. The last generation (APS3)
is associated with late illite which replace the previous diagenetic kaolinite during a
postdating hydrothermal event which is well known to be related with the deposition of the
uranium orebodies in the underlying basement rocks (Riegler et al., 2013).
In the sandstone, the crystals of diagenetic APS tend to be relatively homogenous in
composition with no more than one generation of visible overgrowth showing a slightly
brighter core in BSE mode, indicating the incorporation of more heavy elements during the
first crystallization stage. Unfortunately the crystal size is often smaller than the electron spot
size, permitting not to have EMP measurement of the chemical composition on both core and
overgrowth for these crystals.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
176
Figure 1-4 : a, Oxy-hydroxy aluminium minerals associeted with cerianite grains and exhibiting high Ce levels
up to several percent; b, same AlOOH minerals associated with cerianite, La-Ce oxide and thorianite and related
EDS spectra for these phases:c, c, & e.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
177
1.5.2. Basement Alteration petrography and mineralogy
Figure 1-5 : Primary REE & Uranium bearing minerals in the Kiggavik & St Tropez area, A Non metamict
unaltered monzite grain, Woodburn Group metagraywacke, W97-4; B Parisite (Ca,Ce, La)CO3 euhedral crystal
with local partial dissolution associated with illite formation, granitoid at the bottom of the W97-4 drillhole; C
Altered allanite, Uno granite, D Uranothorite altered to thorogummite, Andrew lake syenite dyke.
Abbreviations, Aln: allanite, Cal: calcite, Par: Parisite, Py: Pyrite, Ttn:titanite
In the basement rocks, APS minerals are closely associated with the hydrothermal alteration
processes which controlled the uranium ore genesis, Figure1-2e. The alteration of basement
rocks is spatially related to faults at every scale. It results in a strong color change of the
rocks. Two contrasting macroscopic alteration features have been noted: (1) bleaching related
to strong argilization and (2) reddish coloration related to crystallization of iron oxide (mostly
hematite) and local silicification of open fractures (quartz veins). Strong argilization
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
178
(bleaching) associated with various degrees of desilicification is the most common alteration
feature observed in both the fault core and the major mineralized zones. At small scale,
alteration is related to the dissolution of the preexisting metamorphic silicates and the
crystallization of an abundant clay matrix composed of illite associated to variable but
generally small amounts of sudoite (Al-Mg chlorite). In altered intrusive rocks, the feldspars
phenocrysts are totally replaced by illite and specular hematite. Sudoite is always intimatly
associated with illite.
Minor amounts of phosphate minerals are closely associated with illite and sudoite. They
essentially consists in aluminum phosphate-sulfate minerals (APS) and secondary apatite and
they display a marked zoning pattern around the mineralized bodies. APS minerals occur as
tiny pseudocubic crystals which size range from less than to 10 µm up to 50 µm. APS
minerals display frequently features of chemical zoning but the ones observed were quite
homogeneous with only one generation of overgrowth and very little compositional change
(Figure1-2f). Secondary apatite occurs close to and within the mineralized zones.
APS minerals are totally absent in the fresh basement rocks. However, several accessory
minerals of these rocks can be considered as the potential source for the chemical elements
incorporated in the APS minerals observed in the altered zones. According to the nature of the
host rock, they can consist in monazite (Figure 1-5a), mostly in the metagraywackes;
bastnaesite/parasite (Figure1-5b), allanite or REE oxides (Figure1-5c) as accessory phases
in granites, ryholites and syenites. In addition uranothorite altered to thorogummite can be
found in place in ryholite (Figure 1-5d). This last mineral being a potential source for both U
and REE.
To sum up the petrographic observations in both the sedimentary and basement rocks, it
appears that two main generations of APS minerals can be identified with respect to their
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
179
relationships with clay minerals. In the Thelon sandstones APS1 & 2 coexist with kaolin
minerals and are related to the basin evolution from sedimentation to deep diagenesis as
indicated by the kaolinite to dickite transition (voir chapitre 4). The second generation of APS
is clearly related to the hydrothermal alteration event associated with uranium mineralization
within the underlying basement rocks. The APS3 observed locally with illite near the bottom
of the Thelon sandstone is considered as a signature of the hydrothermal alteration event
which is extensively developed below the unconformity.
Then, the crystal-chemical properties of APS minerals needs to be investigated in more
details to determine if the textural observation can also be linked to a chemical evolution of
the system and how this would fit in the general mineralization model for the uranium
mineralization found along the Kiggavik Andrew lake structural trend. In addition,
complementary EMP measurements have been done on the REE bearing mineral identified in
the fresh rock (monazite, bastnaesite/parasite, allanite, REE oxides). Complementary data on
accessory uranium-bearing mineral is also presented.
1.6. Electron microprobe data
1.6.1. Overall chemistry of APS minerals
Average representative electron microprobe data of each geological environment have been
sum up in the table 1-2. The low and relatively variable sum of oxide weight percent of the
analyses is a result of the water content of the APS minerals as well as a significant
microporosity between the micrograins aggregates of the X-Ray emitting volume. However,
even if the very small size of the APS minerals increases the possibility of contamination of
the microprobe analysis by chemical elements of surrounding clay minerals or quartz, it has
no significant influence on the relative proportions of the APS forming chemical elements (at
the exception of aluminum).
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
180
Table 1-2 : Representative electron microprobe analyses of APS minerals, B: basement, C, sedimentary cover
B C
Distal Alteration; SL9_01
Intermediate Alteration; SL9_05
Proximal Alteration Zone, BG42_23
GG7_APSCement
GG7_Mtx
GG4 GG3
n = 32 n = 17 n = 17 n = 18 n = 31 n = 9 n = 20
Mean Wt% Std Dv. Mean Wt%
Std Dv.
Mean Wt% Std Dv.
Mean Wt%
Std Dv.
Mean Wt%
Std Dv.
Mean Wt%
Std Dv.
Mean Wt%
Std Dv.
SrO 5.95 1.31 4.61 1.22 3.26 0.76 10.09 0.70 11.31 1.22 7.31 0.95 13.49 1.12
CaO 2.52 0.40 2.31 0.61 1.15 0.28 1.72 0.15 2.18 0.39 3.48 1.04 2.25 0.30
BaO 0.33 0.37 0.31 0.31 0.02 0.03 0.67 0.13 0.72 0.34 0.43 0.31 1.31 0.50
La2O3 6.11 1.63 5.99 1.43 7.71 1.08 5.54 1.04 2.37 1.57 3.00 1.32 1.15 0.28
Ce2O3
6.97 2.06 9.55 1.98 11.60 0.90 2.23 0.72 3.01 0.78 3.69 0.94 1.49 0.42
Pr2O3 0.74 0.21 0.76 0.20 0.97 0.17 0.84 0.13 0.38 0.21 0.67 0.15 0.20 0.07
Nd2O3
2.01 0.76 1.93 0.54 2.27 0.50 2.92 0.48 1.33 0.75 2.92 0.56 0.72 0.28
ThO2 0.36 0.30 0.37 0.43 0.02 0.03 0.30 0.12 0.38 0.13 0.25 0.33 0.36 0.24
Al2O3 29.48 1.42 28.94 1.42 32.78 1.21 31.50 0.55 31.61 1.72 32.70 1.71 31.76 1.00
FeO 0.72 0.66 0.80 0.82 0.08 0.05 1.17 0.50 1.18 0.64 0.54 0.58 1.59 2.28
P2O5 23.65 1.28 24.42 1.56 26.78 2.12 25.75 0.60 23.98 1.84 27.56 2.67 23.31 1.18
SO2 2.35 0.85 1.85 0.87 1.78 1.02 2.10 0.38 3.02 0.74 2.64 0.42 4.73 0.48
Total 81.18 81.83 88.41 84.81 81.48 85.19 82.35
Mean apfu Stdt Dv.
Mean apfu Stdt Dv.
Mean apfu Stdt Dv. Mean apfu
Stdt Dv.
Mean apfu
Stdt Dv.
Mean apfu
Stdt Dv.
Mean apfu
Stdt Dv.
A Sr 0.30 0.06 0.23 0.06 0.15 0.03 0.47 0.03 0.54 0.05 0.33 0.05 0.62 0.04
Ca 0.23 0.03 0.21 0.06 0.10 0.02 0.15 0.01 0.19 0.03 0.29 0.09 0.19 0.02
Ba 0.01 0.01 0.01 0.01 0.00 0.00 0.02 0.00 0.02 0.01 0.01 0.01 0.04 0.02
La 0.20 0.06 0.19 0.05 0.23 0.03 0.17 0.03 0.07 0.05 0.09 0.04 0.03 0.01
Ce 0.22 0.07 0.30 0.06 0.34 0.03 0.07 0.02 0.09 0.02 0.11 0.02 0.04 0.01
Pr 0.02 0.01 0.02 0.01 0.03 0.00 0.02 0.00 0.01 0.01 0.02 0.00 0.01 0.00
Nd 0.06 0.02 0.06 0.02 0.07 0.01 0.08 0.01 0.04 0.02 0.08 0.02 0.02 0.01
Th 0.01 0.01 0.01 0.01 0.00 0.00 0.01 0.00 0.01 0.00 0.00 0.01 0.01 0.00
B Al 2.99 0.05 2.96 0.06 3.11 0.09 3.01 0.05 3.05 0.09 3.01 0.10 2.99 0.10
Fe 0.05 0.05 0.06 0.06 0.01 0.00 0.08 0.03 0.08 0.04 0.04 0.04 0.10 0.15
X P 1.72 0.04 1.79 0.08 1.83 0.11 1.77 0.04 1.66 0.09 1.82 0.11 1.58 0.07
S 0.19 0.06 0.15 0.07 0.14 0.09 0.16 0.03 0.23 0.06 0.19 0.04 0.35 0.03
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
181
Table 1-3 : Electron microprobe analyes of primary REE and U bearing minerals in the Kiggavik-St Tropez area, n number of analyses; the low total elements for monazite could be
explained by the fact that Pb, Y, Sm, Ga haven’t been analysed.
Hudson Granite Metagraywackes
Bastnaesite/Parisite Allanite Monazite Thorogummite Thorogummite Monazite
W97-4_10 & 17; W2 Uno W97-4; W2; Uno; Granite Grid
W97-4_17 W97-4_10 W97-4_3
n= 26 n= 5 n= 8 n= 4 n= 3 n= 14
wt% Mean Std Dv. wt% Mean Std Dv. wt% Mean Std Dv. wt% Mean Std Dv. wt% Mean Std Dv. wt% Mean
Std Dv.
F 3.26 0.40 0.20 0.02 0.37 0.04 0.68 0.09 0.34 0.05 0.40 0.06
Al2O3 0.13 0.36 11.76 0.60 0.10 0.11 0.22 0.11 0.39 0.09 0.07 0.04
P2O5 0.00 0.01 0.31 0.26 24.88 2.14 0.25 0.25 1.81 0.39 26.19 1.46
SO2 0.00 0.00 0.00 0.00 0.00 0.01 1.06 1.01 0.46 0.44 0.29 0.25
CaO 17.07 0.70 8.90 0.36 0.55 0.35 1.57 0.14 2.84 0.36 1.16 0.43
FeO 0.36 0.94 12.31 0.98 0.85 1.26 1.95 1.04 2.04 1.46 0.15 0.14
SrO 0.02 0.03 0.28 0.04 0.11 0.13 0.08 0.06 0.05 0.03 0.20 0.11
La2O3 13.63 0.76 4.45 0.73 16.11 2.11 0.21 0.05 0.07 0.05 16.92 1.05
BaO 0.02 0.04 0.56 0.11 0.06 0.08 0.06 0.05 0.36 0.38 0.03 0.05
Pr2O3 2.43 0.21 0.82 0.28 3.22 0.21 0.15 0.09 0.25 0.06 3.32 0.13
Nd2O3 8.70 1.10 2.57 1.32 9.68 1.19 1.41 0.39 0.95 0.29 11.41 0.90
UO2 0.06 0.07 0.11 0.08 0.15 0.15 4.20 2.12 0.90 0.47 0.09 0.08
ThO2 0.23 0.63 1.02 0.22 4.29 2.71 53.32 3.19 56.10 2.63 0.49 0.65
Ce2O3 25.30 1.37 9.33 1.22 30.79 1.53 0.86 0.19 0.84 0.22 31.82 1.20
SiO2 0.15 0.43 28.55 0.84 1.88 1.22 13.45 0.88 13.22 0.20 0.18 0.07
Total 71.36 1.00 81.18 4.07 93.04 2.82 79.47 4.47 80.64 2.32 92.73 1.83
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
182
Nevertheless it appears that a clear chemical distinction can be made between APS minerals
from the siliciclastic sedimentary cover, (C) and those from the basement (B), table 1-2. APS
minerals from the siliciclastic sedimentary cover are Sr ,Fe and SO2 rich while APS minerals
of the hydrothermal alteration zones are enriched in LREE with a concentration 2 to 3 times
higher than in the APS form the sandstones, and correlatively lower Sr and SO2. These global
consideration leads to the identification of two chemical fields of APS minerals easily
differentiated in a Sr/LREE/S ternary diagram, figure 1-6. The first chemical field which is
next to that of svanbergite, is representative of the sedimentary and diagenetic APS (GG3,
GG7) samples. The second compositional field which is next to the one of florencite is
representative of the hydrothermal APS of the altered basement (SL1&SL5 and BG42).
Figure 1-6 : Ternary plot using Sr, LREE & S composition of APS minerals obtained from electron microprobe
analysis. mineralized metagraywackes ◊ Mineralized zone graywacke BG4β, □ proximal to mineralization in
granite SL9, ■ distal to mineralization SL9, ▲ sandstone GG7, ▽ sandstone GG3, △ sandstone GG4
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
183
In both chemical fields, the compositional variation of Sr and LREE follows the same
direction with a distribution of analyses between a Sr (svanbergite, goyazite) and a LREE rich
(florencite) end members. Lastly, the GG4 sample represents a group of APS minerals with
intermediate chemical composition between the APS of unaltered sandstones and those of the
illitized basement especially for the Sr and LREE contents.
Figure 1-7 : Ternary plot using La, Pr+Nd & Ce of electron microprobe data on APS minerals form Thelon
formation conglomeratic sandstones and altered as well as mineralized metagraywackes. Mineralized zone
graywacke BG42, □proximal to mineralization in granite SL9, distal to mineralization SL9, ▲ sandstone
GG7, ▽ sandstone GG3, △ sandstone GG4
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
184
The relative proportion of the LREE incorporated in the APS minerals (La,Ce,Pr,Nd) can be
illustrated using a La/Pr+Nd/Ce ternary diagram, figure 1-7. Over all the APS minerals
analyzed, the greatest variability in LREE relative proportions correspond to the cerium in the
APS minerals from the sandstone and more particularly for the GG7 sample (solid triangle
pointing up) with a broad range LREE proportion, from high Ce in the matrix APS to low in
the massive APS cement. Such a feature of strong variation of cerium content in the APS
minerals while La/Pr+Nd ratio is constant needs to be look at jointly with the presence of
cerianite. Then, cerium might had been fractionated between Ce-oxide and APS minerals
during the crystallization stage of early APS1. In the altered basement the relative
proportions of APS seems broadly constant with a predominance of cerium over the other
LREE elements (figure 1-6).
1.6.2. Element distribution in crystallographic sites
As already demonstrated, (Dill, 2001; Gaboreau et al., 2005; Gaboreau et al., 2007), APS
minerals are subject to numerous and various substitutions in the A, B and X sites forming
solid solution between ten’s of end members of the alunite supergroup. Moreover, the chemo-
sensitive behavior of APS mineral have been identified in the selective incorporation of REE
depending mainly on Eh and to a less extent on pH of the forming environment.
The global composition of the different types of APS minerals identified in various locations
along the Kiggavik Andrew lake structural trend preferentially varies in response to coupled
substitutions of Sr and LREE in their A site and P and S in their X site. In the altered
basement rocks both intra- and inter-sample chemical variations of APS range along a binary
solid solution between Svanbergite [Sr(Al3)(PO4,SO4)(OH)6] (which belongs to the beudantite
group) and Florencite [LREE( Al3)(PO4)2(OH)6] (which belong to the the crandallite group).
Sr-rich APS minerals (closer to the Svanbergite end member) are associated with non-altered
to distal alteration zone while APS minerals with the highest LREE content were analysed
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
185
within the mineralized zones, and more particularly in the ore grade mineralization zone in
which LREE-rich APS can coexist with secondary apatite.
In the overlying sandstones, the compositional variation of APS cannot be explained only by a
change in svanbergite to florencite solid solution. Indeed, the fact that all the punctual
analyses are anomalously enriched in of Sr versus S (figure 8) is indicative of a significant
contribution the Goyazite end-member [SrAl 3(PO3[(O0.5(OH)0.5]2(OH)6] to the crystal-
chemistry of these minerals.
Figure 1-8 : Cross plot diagram S versus Sr of APS minerals
1.6.3. Chemistry of primary REE bearing minerals
Representative electron microprobe analyses given in % oxydes of primary REE and U, Th
bearing mineral are presented in the table 1-3.
0.00
0.20
0.40
0.60
0.00 0.20 0.40 0.60 0.80
S (
ap
fu)
Sr (apfu)
SL9_01 SL9_05 BG42_23
GG3 GG4 GG7
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
186
As described in the previous petrographic study, several primary REE-bearing minerals are
found in the unaltered basement rocks in which they belong to magmatic or metamorphic
paragenesis.
Rare earth carbonates are widely encountered in the Hudson granite but their concentration is
to low to permit their characterization by classical X-ray diffraction methods, even after
heavy minerals concentration using sodium polytungstate at a density of 2.9. Nevertheless the
punctual EMP analysis provides valuable information to identify REE carbonates on the basis
of the low sum of oxide weight % (near 70%) and the qualitative analysis of carbon on the
EDS spectra and the overall chemistry. The most common REE carbonates of igneous rock
are: bastnaesite (Ce,La)CO3F, parisite Ca(Ce,La,Nd)(CO3)2F2, and synchysite
Ca(Ce,La)(CO3)2F. The ternary Thorium, calcium and total rare earth plot for the assumed
carbonates, figure 1-9 shows that the REE carbonates are closer to the parisite end member
with relatively high calcium content. More interesting, when plotted in a La/Pr+Nd/Ce ternary
diagram (figure 9), all these minerals have a composition which is superimposed on the
composition field determined for most of the APS minerals of the basement rocks (figure 6).
The second groups of REE bearing minerals are the monazites with higher thorium content in
the Hudson granite monazite than in the metagraywacke ones table 1-3, 1-4. The low sum of
oxide Wt% of the monazite analyses are explained by the fact that HREE have not been
analyzed.
The following simplified structural formulas (without HREE) can be calculated for the
monazite, Table 1-4.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
187
Figure 1-9 : Ternary plot using La, Pr+Nd & Ce, of electon microprobe chemical composition on REE bearing
minerals in unaltered Woodbun metagraywackes & Hudson granitoids in the Kiggavik & St Tropez area: ▲
monazite, allanite, REE oxides ? , REE carbonates. The field of composition and the phase
identification for REE carbonates is given in the Ca, Th, REE ternary diagram.
Table 1-4 : Mean simplified structural formulas of monazite analysed in both the metagraywacke and Hudson
granite. n: number of microprobe analysis
Metagraywacke Hudson Granite
n= 14 n= 8
(Ce0.50,La0.27,Pr0.05,Nd0.17,Th0.00)P0.95O4 (Ce0.51,La0.27,Pr0.05,Nd0.16,Th0.05)P0.93O4
Finally, allanite, zircon and uranothoriferous minerals occurs in the Hudson granite.
Uranothorite is frequently altered and replaced by thorogummite with up to 8% UO2, table 1-
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
188
3. Moreover the Ce, and Nd concentration of the thorogummite (up to 1%) make this mineral
a minor REE source released during the alteration processes.
This result highlights the potential role of the Hudson granite as a regional source of uranium,
and REE while monazite is globally uranium poor but nevertheless a very good candidate as
LREE primary source.
Monazite has not been identified in the sandstone cover probably because of its total
dissolution during the diagenetic processes.
1.7. Whole rock chemistry and REE distribution
The crystal-chemical study of REE and U bearing minerals has been completed by a bulk-
rock chemical analysis of major and trace elements in order to identified the geochemical
behavior of these elements and to to evaluate the elements transfers during the alteration-
mineralization processes.
As the evaluation of a mass transfer requires the assumption of immobile elements, Ti, Al and
Th (or Zr which is not represented in figure 9) have been tested by a comparative study of
their relative proportions in both unaltered and altered rocks of a same metagraywake
protolith. A plot of the relative proportions of these elements from all the unaltered to highly
altered samples of metagraywakes in a ternary diagram (figure 1-10) indicates that the Al and
Ti relative percentages remain constant while elements such as Th or Zr (not represented in
figure 9) slightly vary. Such a geochemical behavior which is enhanced by the factor 1000
used in the ternary plot can be easily explained by bedding heterogeneities in the
metasediments. A similar behavior is observed when Th or Zr have been replaced by the sum
of LREE in the ternary plot. This indicates that Ti and Al can be considered as immobile
elements in the system while minor changes in Th, Zr and LREE, can be reasonably assigned
to the sedimentary control on the amount of detrital heavy minerals (zircon, monazite…).
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
189
However, the inter-sample variation in Th concentration which is quite low and has probably
no significant impact on the use of Th, Ti or Al for mass balance calculation.
Figure 1-10 : Plot of the chemical composition of all the unaltered to highly altered samples
of metagraywakes in a Ti, Th*1000, Al/10 ternary diagram. (□) altered metagraywacke and
(■) unaltered metagraywacke.
1.7.1. Pearce analysis & Mass balance calculation
Petrography and crystal chemistry lead to the identification of the REE ratio and content on
both fresh and altered rocks. Pearce Element ratio analysis (PER) and mass balance
calculation have been used to approach the chemical transfer during alteration.
At first, local redistribution needs to be assess comparing the samples of the altered zone. In
the figure 1-11a, the Ce/Th and Al/Th molar ratio behavior gives a representation of the
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
190
redistribution of cerium in APS minerals during the alteration of monazite. It appears that
some samples are depleted in LREE while other are enriched, this being concordant with the
heterogeneities in APS content inside the illite & sudoite alteration halos. In addition the
Ce/Th vs La/Th reveals that very little fractionation between the various REE occurs figure
11b. This is in agreement with the La/Pr+Nd/Ce ternary diagrams where the LREE proportion
between the sources minerals and APS is fairly constant. Then alteration and crystallization of
REE phases seems to be a topochemical processes leading to a redistribution of REE at small
scale inside the alteration halos.
Figure 1-11 : Pearce element ratio diagrams for unaltered and altered metagraywackes representing. a, the
monazite and the florencite, and b evolution of REE ratios relatively to Th
The low mobility of REE can also be noticed in the mass balance calculation, figure 12. That
method gives an estimate of the elemental transfers during alteration processes. The
calculations have been done using both thorium and titanium as reference for immobile
elements. The error on elements loss or gain is given by the relative loss or gain on the
element chosen as immobile. In addition the concentration in the altered rock was corrected as
a function of the rock density using d = 2.70.02 for the unaltered rock and d = 1.70.2 in
0
2
4
6
8
10
12
14
0 500 1000
Ce / T
h
Al / Th
unaltered
altered
a
y = 1.99x - 0.42 R² = 0.98
y = 1.46x + 0.06 R² = 0.99
0
2
4
6
8
10
12
14
0 5 10
Ce /T
h
La / Th
unaltered
altered
b
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
191
the altered equivalent on the basis of the determination of the density of 4 and 5 representative
samples in laboratory. These values are in agreement with the density estimated from
geophysical methods in the literature (respectively 2.7 and 2.3) (Hasegawa et al. 1990). The
alteration is marked by a relative but moderately significant increase in Al, K, Mg concordant
with the dissolution of the primary minerals (quartz, feldspars, biotite, chlorite and pyrite) and
followed by the crystallization of illite and sudoite.
It can be noted that iron is globally leached out of the system, especially when Th is used as
the immobile element in agreement with the pervasive hematization observed around the main
alteration zones.
The enrichment in phosphorus in altered zone is not only related to formation of APS
minerals because secondary apatite is the most frequent P-bearing mineral of the alteration
halo close to the uranium orebodies.
Considering the trace elements, an important result of the mass balance calculation is the
strong enrichment in U, V and Mo and the substantial gain in Bi, Co, Cr, Ni, W elements with
increasing alteration (expressed by an increase of loss on ignition).
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
192
Figure 1-12 : Mass balance analysis for metagraywacke Ti & Th as stable elements. Corrected for density change using (average measured densities 2.7 for fresh and 1.7 for
altered metagraywacke)
-500
0
500
1000
1500
2000
2500
3000
3500
4000
4500
As
Ba
Be
Bi
Cd
Ce
Co
Cr
Cs
Cu
Dy
Er
Eu
Ga
Gd
Ge
Hf
Ho
In
La
Lu
Mo
Nb
Nd
Ni
Pb
Pr
Rb
Sc
Sb
Sm
Sn
Sr
Ta
Tb
Th
Tm
U
V
W
Y
Yb
Zn
Zr
SiO
2
Al2
O3
Fe2O
3
MnO
MgO
CaO
Na2O
K2O
TiO
2
P2O
5
Relative Loss/Gain % corrected to densities
Ti as immobile element
Th as immobile element
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
193
1.8. Discussion
Evidences from petrography and mineral crystal-chemistry support the successive occurrence
of three types of APS minerals in the sedimentary and basement rocks encountered on both
sides of the paleoproterozoic unconformity at which the uranium deposits in the Kiggavik
Andrew lake structural trend are related (Riegler et al., 2013). APS minerals have been
already described in the paleoproterozoic Thelon and Hornby Bay basins (Gall and
Donaldson, 2006). They have been also extensively investigated in both altered basement
rocks and sedimentary cover which constitute the alteration halos of the unconformity related
uranium deposits of the Athabasca and Kombolgie basins (Beaufort et al., 2005; Gaboreau et
al., 2005; Gaboreau et al., 2007).
The paragenetic sequence established from the petrographic study permitted to distinguish
three different populations of APS minerals which can be related respectively to sedimentary
(APS1) and diagenetic (APS2) processes in the sandstones of the basal Thelon formation and
to hydrothermal alteration (APS3) strongly developed in the basement rocks next to the
regional faults and much weakly developed in the overlying Thelon sandstone (Figure 1-3).
The three distinctive generation of APS can be also distinguished on the basis of their crystal-
chemical properties. When plotted in a diagram Ce2O3/La2O3 versus the total amount of the
most abundant light rare earth elements (La2O3 + Ce2O3+ Nd2O3), three distinct compositional
fields can be distinguished (figure 13):
1.8.1. Crystal-chemical signature of sedimentary and diagenetic APS of the
Kiggavik area
The APS related to the sedimentary and the diagenetic history (APS1 and APS2) differ from
the hydrothermal ones (APS3) by their lower content in LREE and a great scattering of their
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
194
Ce2O3/La2O3 ratio. However this apparent scattering of the APS crystal chemistry within the
basal sandstones can be interpreted in more details on the basis of the petrographic
observations.
The sedimentary APS which are associated with detrital aluminum oxi-hydroxides and cerium
oxides are characterized by a relatively high LREE oxide content (8 to 13%) and a strong
depletion in cerium (Ce2O3/La2O3 ratio less than 0,5) whereas the compositional field of the
diagenetic APS (APS2) characterized by a lower total amount of LREE oxide (from 2 to 7%)
and a variable but quite much higher Ce2O3/La2O3 ratio (from 1 up to 7) which spread over
the composition of APS analysed in upper sandstones elsewhere in the Thelon basin (Gall and
Donaldson, 2006). The variation of the Ce/La and total amount of LREE measured in the APS
formed in sandstones could be related to change in the nature of the sedimentary material. For
instance, the Wharton Group is known to host volcano-sedimentary sequences with rhyolitic
tuffs (Miller and LeCheminant, 1985; Rainbird and Davis, 2007; Rainbird et al., 2003), and
given the highly instable nature of such material and the large volumes possibly involved the
contribution of these lithologies to the LREE budget can be assumed. However we cannot
easily interpreted the APS compositional variations as the result of a chemical change in the
source material because bulk-rock chemical analyses of the sandstone samples do not indicate
any significant variation in total amount of rare earth or in Ce/La ratio.
A better explanation can be found in the possibility of partitioning of rare earth elements
between coexisting mineral phases. Such a phenomenon can be invoked for the chemistry of
the Ce-depleted APS1 minerals which coexist with cerianite and Al-oxi-hydroxides. Indeed,
All these aforementioned minerals as well as kaolinite and iron hematite are well known to
be the typical mineral assemblage of the continental alterites in tropical climatic conditions.
APS can be found in modern laterites (Seghal 1998; Sehnke 1993), and the presence of
persevered Al oxy-hydroxide and CeO2 are also indicative of lateritic environments. In such
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
195
alterites, cerium, preferentially present in the Ce4+ oxidizing state (Braun et al. 1990), is rather
incorporated in cerianite (CeO2) than in other minerals such as APS in which Ce is
preferentially incorporated in the Ce3+ state. The above considerations lead us to interpret the
specific crystal chemistry of the APS1 as an inheritage of their condition of formation during
the paleoweathering (regolith) of the continental crust prior the formation of the Thelon basin.
In other words, such a geochemical signature confirms that dismantled regolith was involved
in the source material of the sedimentation at the first filling stage of the basin.
The presence of coexisting REE-bearing phases has not been clearly identified in the case of
the diagenetic APS2 which are characterized by low REE content and high Ce/La. Diagenetic
fluorapatite has been identified elsewhere in the Thelon basin (Gall and Donaldson, 2006) but
its REE content remains very low and no information on their Ce/La ratio is available.
However APS related to early diagenetic processes have been already documented in other
siliciclasic basins in which other REE-bearing minerals can be present (Rasmussen, 1996, Pe-
Piper and Dolansky, 2005).
1.8.2. Crystal-chemical signature of the hydrothermal APS of the Kiggavik
area
The hydrothermal APS which coexist with illite and minor sudoite in the altered basement are
characterized by a high LREE oxide content (13 to 26%) and a nearly constant Ce2O3/La2O3
ratio (between 1 and 2) which fits fairly well with the Ce2O3/La2O3 ratio of the parental
REE-bearing minerals which still persist in the unaltered basement rocks (Figure1-13, Table
1-3). This is indicative of the absence of rare earth elements fractioning during the
hydrothermal alteration process and agree with the rather immobile behavior of these
chemical elements which are essentially incorporated in the APS3 minerals which crystallize
close to the site of primary LREE-bearing minerals dissolution (monazite, bastnaesite,
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
196
parasite …). The first consequence of this phenomenon is the preservation of the relative ratio
of LREE, figure 1-14.
Figure 1-13 : Ce/La oxides ratio verus the sum of REE in APS minerals from the cover and the
basement. Data from Gall & Donaldson, 2006 as a comparison for sandstone APS minerals
0
2
4
6
8
10
12
14
0 5 10 15 20 25 30
Ce2
O3
/La2
O3
LREE (oxide wt%)
APS from altered basement
APS from sandstone cover
APS from Thelon Fm (Gall and Donaldson., 2006)
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
197
Figure 1-14 : Synthetic plot of composition field REE ratio for all APS minerals in the
Kiggavik area and the primary REE minerals
However, the major compositional variation of APS3 consists in their large range of total
LREE content which variation seems well correlated with the distance to the uranium
mineralization. Such a variation has been already demonstrated in other unconformity related
uranium deposits (Gaboreau et al., 2005, 2007) and is interpreted as a result of Eh-pH
variations in the alteration system. Regarding the previous works made on the Eh/Ph control,
(Dill, 2001; Kolitsch and Ping, 2001), the evolution between the Svanbergite Sr-end member
to the Florencite REE end of APS minerals can be interpreted as an evolution from low pH
oxidizing to more reduced and higher pH conditions (Gaboreau et al., 2005). Then the fact
that LREE-rich APS coexisting with secondary apatite crystallized close to the uranium
orebodies whereas APS with lower LREE content were crystallized outer in the alteration
halo is interpreted as the result of a time-space chemical evolution of the infiltrating fluid
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
198
which Eh and pH progressively change towards more reducing and more neutral conditions
with increasing interaction with the minerals of the basement rock. Such a geochemical
process could be the cause of the synchronous deposition of uranium mineralization and
LREE-rich APS in both the Athabasca and Kombolgie unconformity type uranium deposits
(Gaboreau et al., 2007, Beaufort et al., 2005 among others).
Finally the mass-balance calculation related to the hydrothermal alteration of basement rocks
lead to a geochemical signature similar to the one found in unconformity type uranium
deposits in the Athabasca Basin (Hoeve and Sibbald 1978; Quirt 1997; Ruzicka 1993) but
also in the Amer Group uranium occurrences, (Miller and LeCheminant 1985) with among
others an increase in Bi, Co, Mo, V, W & U. All these elements been described in the
Athabasca basins either associated to red bed or in lateritic profile to ferric iron hydroxides
and thought to be a possible sources for these metals (Macdonald 1980; Mosser et al. 1985;
Wedepohl 1978).
All the above considerations lead us to interpret the crystal-chemical variations of the
hydrothermal APS related to the uranium deposits in the Kiggavik Andrew lake structural
trend as the consequence of the same geochemical processes than those already identified in
basement-hosted unconformity-related uranium deposits worldwide.
1.8.3. Comparing the overall APS compositional field at Kiggavik with that
of unconformity-related uranium deposits worldwide
First of all one of the striking chemical feature observed previously in both Athabasca and
Kombolgie basin is a fairly continuous range of composition of APS mineral from zone
proximal to mineralization to barren altered and finally the unaltered sedimentary rocks in the
basins (Gaboreau et al, 2005, 2007). The compositional field is then going roughly from the
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
199
florencite end-member to the svanbergite end-member, disseminated along a steady slope
given by the constant S/Sr ratio, in a Sr-LREE-S ternary diagram figure 1-15.
Figure 1-15 : Comparison of the compositional field of the APS mineral from the Kiggavik area (dotted lines)
with those of APS minerals determined by Gaboreau et al. (2005, 2007) in both the Athabasca & Kombolgie
basins .
On the opposite the in-situ chemical data gathered on APS mineral from the Kiggavik area
shows two groups of minerals with different S/Sr ratio according to the fact that APS mineral
are found in the altered basement or in the un-altered sedimentary cover. The first group of
APS in the altered basement, defines a composition envelop chemically very similar to that
established in the Athabasca and Kombolgie basins. Then, as the conclusions of the first
studies on alteration lead to relate the Kiggavik Andrew lake trend uranium deposits to an
unconformity related type of mineralization, APS minerals had a similar forming history in
these three basins when basement alteration is considered. The second group in the sandstones
defines an envelope of composition which slightly overlaps the Athabasca trend nevertheless
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
200
with a steeper slope of the composition envelop. This highlights the predominant role of the
S/Sr ratio in the Thelon APS when the Sr/LREE explains more the composition variability in
the Athabasca sandstones. Such chemical differences illustrates the chemical specificity of the
APS minerals of the basal sandstones of the Thelon formation which have been mostly
preserved of the hydrothermal alteration related to the basement hosted uranium
mineralization and highlight their interest as markers of the basin evolution prior the
occurrence of the U-mineralizing hydrothermal event. Contrary to other unconformity-related
uranium deposits, the APS minerals of the sandstones which locally overly the basement
hosted uranium deposits of the Kiggavik area cannot be considered as reliable indicators of
the deep seated mineralizing process because they are inherited minerals from the earlier
basin history which have been preserved from hydrothermal alteration in an unaltered
compartment.
Finally the geochemistry lead to the identification of geochemical signature of alteration
similar to the one found in unconformity type uranium deposits in the Athabasca Basin
(Hoeve and Sibbald 1978; Quirt 1997; Ruzicka 1993) but also in the Amer Group uranium
occurrences, (Miller and LeCheminant 1985) with among others an increase in Bi, Co, Mo, V,
W & U. All these elements been described in the Athabasca basins either associated to red
bed or in lateritic profile to ferric iron hydroxides and thought to be a possible sources for
these metals (Macdonald 1980; Mosser et al. 1985; Wedepohl 1978).
1.9. Conclusion
The concluding remarks of this study are :
(1) The similar trend of composition for hydrothermally related APS minerals in the basement
and locally in the sandstone cover where illitization takes place. The chemical zonation
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
201
expressed in the LREE enrichment is the same as in the Athabasca and the Kombolgie
unconformity type uranium mineralization occurrences.
(2) To confirm and implement the knowledge of the relationship between the hydrothermal
APS and the ones related to an early diagenetic stage during the basin evolution, similar to the
APS cementation observed in Paleozoic siliciclastic basins, (Pe-Piper and Dolansky 2005).
Moreover the chemical composition of sedimentary cover APS is pro parte in a similar trend
than APS minerals observed in other location within the Thelon. However, new evidence
leads to the identification of pre diagenesis APS minerals. This features, enhanced here by the
pristine conservation of the most early sedimentation stages would be very likely the same in
the Athabasca Basin, in place with no later alteration overprint.
These two facts lead to the conclusions that APS should be observed as markers of a long
lived evolution of the basin some being related to the mineralization and alteration events in a
range of temperature in the range of hydrothermalism, somehow link to thermal peak during
the diagenesis when the others are the relicts of laterites related to the paleoweathering, as
well as witness of the early cementation during diagenesis.
Finally, APS minerals unique mineralogical markers able to record equally the early processes
related to the sedimentation and diagenesis of these Meso-Proterozoic basins. Nevertheless
their complex history doesn’t allow the use of the APS minerals as direct mineralogical
pathfinders to alteration and then mineralization.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
202
1.10. References
Braun J-J, Pagel M, Muller J-P, Bilong P, Michard A, Guillet B (1990) Cerium anomalies in lateritic profiles. Geochimica et Cosmochimica Acta 54:781-795. doi: http://dx.doi.org/10.1016/0016-7037(90)90373-S.
Beaufort, D., Patrier, P., Laverret, E., Bruneton, P., and Mondy, J., 2005, Clay Alteration Associated with Proterozoic Unconformity-Type Uranium Depositsin the East Alligator Rivers Uranium Field, Northern Territory, Australia: Economic Geology, v. v. 100, p. pp. 515–536.
Cloutier J, Kyser K, Olivo GR, Alexandre P (2010) Contrasting Patterns of Alteration at the Wheeler
River Area, Athabasca Basin, Saskatchewan, Canada: Insights into the Apparently Uranium-
Barren Zone K Alteration System. Economic Geology 105:303-324. doi:
10.2113/gsecongeo.105.2.303.
Dill, H.G., 2001, The geology of aluminium phosphates and sulphates of the alunite group minerals: a review: Earth-Science Reviews, v. 53, p. 35-93.
Gaboreau, S., Beaufort, D., Vieillard, P., Patrier, P., and Bruneton, P., 2005, Aluminum phosphate- sulfate minerals associated with Proterozoic unconformity-type uranium deposits in the East Alligator River Uranium Field, Northern Territory, Australia: Canadian Mineralogist, v. 43, p. 813-827.
Gaboreau, S., Cuney, M., Quirt, D., BEAUFORT, D., PATRIER, P., and Mathieu, R., 2007, Significance of alumium phosphate-sulfate minerals associeted with U unconformity-type deposits: The Athabasca basin, Canada: American Mineralogist, v. 92, p. 267-280.
Gall, Q., and Donaldson, J.A., 2006, Diagenetic fluorapatite and aluminum phosphate-sulphate in the pPelaoproterozoic Thelon Formation and Hornby Bay Groupe, northwestern Canadian Shield: Canadian Journal of Earth Sciences, v. 43, p. 617-629.
Hartlaub, R.P., Heaman, L.M., Ashton, K.E., and Chacko, T., 2004, The Archean Murmac Bay Group: evidence for a giant Archean rift in the Rae Province, Canada: Precambrian Research, v. 131, p. 345-372.
Hasegawa K, Davidson GI, Wollenberg P, Yoshimasa I (1990) Geophysical exploration for
unconformity-related uranium deposits in the northeastern part of the Thelon Basin,
Northwest Territories, Canada. Mining Geology 40:83-95.
Herold, H., 1987, Zur Kristallchemie und Thermodynamik der Phosphate und Arsenate vom
Crandallit-Typ., Erlangen University.
Hoeve J, Sibbald TII (1978) On the genesis of the Rabbit Lake and other unconformity-type uranium deposits in Northern Saskatchewan, Canada. Economic Geology 73. Hoeve, J., and Quirt, D., 1984, Mineralization and host rock alteration in relation to clay mineral diagenesis and evolution of the Middle-Proterozoic Athabasca basin, Northern Saskatchewan, Canada, Saskatchewan Research Concil Technical report, Volume 197, Saskatchewan Reasearch Council, p. 197.
Hoffman, P.F., 1990, Subdivision of the Churchill Province and extent of the Trans-Hudson orogen, in Lewry, J.F., and Stauffer, M.R., eds., The Early Proterozoic Trans-Hudson Orogen of North Amercia, Volume 37: Special paper, Geological Survey of Canada Special Paper, p. 15-39.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
203
Jefferson, C.W., Thomas, D.J., Gandhi, S.S., Ramaekers, P., Delaney, G., Brisbin, D., Cutts, C., Portella, P., and Olson, R.A., 2007, Unconformity-associeted uranium deposits of the Athabasca Basin, Saskatchewan and Alberta, EXTECH IV, Volume Geology and Unranium EXploration TECHnology of the Proterozoic Athabasca Basin, Saskatchewan and Alberta, p. 23-67.
Kolitsch, U., and Ping, A., 2001, Crystal chemistry of the crandallite, beudantite and alunite groups: a review and evaluation of the suitability as storage materials for toxic metals: Journal of Mineralogical and Petrological Sciences, p. 67-78.
Macdonald R (1980) Mineralogy and geochemistry of a Precambrian regolith in the Athabasca Basin.
University of Saskatchewan, Saskatoon, pp 151.
Miller AR (1983) A progress report: uranium phosphorus association in the Helikian Thelon Formation and Sub-Thelon saprolite, central district of Keewatin, NWT. Current Research GSC 83-1A:449-456
Miller, A.R., and LeCheminant, A.N., 1985, Geology and uranium metallogeny of Proterozoic supracrustal successions, central District of Keewatin, N.W.T with comparisons to northern Saskatchewan, Geology of uranium deposits, Volume Special Vol. 32, Canadian Institute of Mining and Metalurgy, p. 167-185.
Mosser C, Leprun JC, Blot A (1985) Les éléments traces des fractions < 2 m à kaolinite et smectite formées par altération de roches silicatées acides en Afrique de l'Ouest (Sénégal et Haute-Volta). Chemical Geology 48:165-181. doi: http://dx.doi.org/10.1016/0009-2541(85)90044-0.
Pe-Piper, G., and Dolansky, L.M., 2005, Early diagenetic origin of Al phosphate-sulfate minerals (woodhouseite and crandallite series) in terrestrial sandstones, Nova Scotia, Canada: American Mineralogist, v. 90, p. 1434-1441.
Pehrsson, S., Jefferson, C.W., Peterson, T.D., Scott, J., Chorlton, L., Hillary, B., Patterson, J., Lentz, D., Shelat, Y., and Bethune, K., 2010, Basement to the Thelon Basin, Nunavut- Revisited, GeoCanada2010: Calgary.
Peterson, T.D., Van Breemen, O., Sandeman, H., and Cousens, B., 2002, Proterozoic (1.85-1.75 Ga) igneous suites of the Western Churchill Province: granitoid and ultrapotassic magmatism in a reworked Archean hinterland: Precambrian Research, v. 119, p. 73-100.
Quirt D (1997) Athabasca Basin Uranium metallogenic model Thermotectonic and uranium metallogenic evolution of the Wollaston EAGLE project Area. Saskatchewan Research Council, Saskatoon, pp 1-41.
Rainbird, R.H., and Davis, W.J., 2007, U-Pb detrital zircon geochronology and provenance of the late Paleoproterozoic Dubawnt Supergroup: Linking sedimentation with tectonic reworking of the western Churchill Province, Canada: Geological Society of America Bulletin, v. 119, p. 314-328.
Rainbird, R.H., Hadlari, T., Aspler, L.B., Donaldson, J.A., LeCheminant, A.N., and Peterson, T.D., 2003, Sequence stratigraphy and evolution of the Paleoproterozoic intracontinental Baker Lake and Thelon basins, western Churchill Province, Nunavut, Canada: Precambrian Research, v. 125, p. 21-53.
Rasmussen, B., 1996. Early-diagenetic REE-phosphate minerals (florencite, gorceixite, crandallite, and xenotime) in marine sandstones: a major sink for oceanic phosphorus. American Journal of Science, 296, 601-632.
Ruzicka VR (1993) Unconformity type uranium deposits In: Kirkham RV, Sinclair WD, Thorpe RI, Duke JM (eds) Mineral Deposit Modeling. Geological Survey of Canada, Ottawa, pp 125-149.
Stoffregen, R.E., 1993, Stability relations of jarosite and natroalunite at 100–250°C: Geochimica et Cosmochimica Acta, v. 58, p. 903–916.
Stoffregen, R.E., and Alpers, C.N., 1987, Woodhouseite and svanbergite in hydrothermal ore deposits: products of apatite destruction during advanced argilic alteration: Canadian Mineralogist, v. 25, p. 201-211. Seghal J (1998) Red and lateritic soils. Rotterdam.
Spatial distribution and compositional variation of APS minerals related to uranium deposits in the Kiggavik Andrew lake structural trend, Nunavut, Canada.
204
Sehnke E (1993) REFRACTORY-GRADE BAUXITE: AN OVERVIEW- 1993 Unitecr'93 Congress Refractories for the New World Economy Proc Conf Sao Paulo, 31 October-3 November 1993. pp 658-670.
Wedepohl KH (1978) Handbook of Geochemistry I, II. Springer Verlag, Berlin, New York.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
205
2. Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
Riegler, Thomas; Allard, Thierry; Beaufort, Daniel. in preparation for submission to Physics
and Chemistry of Minerals
2.1. Introduction
Illite is a common clay mineral, widespread in various geological contexts from soils, to
sedimentary basins or hydrothermal systems. It is formed of a tetrahedral-octaedral-tetraedral
layered structure, with a closed interlayer space occupied by potassium ions. Radiation
induced defects (RIDs) spectrum, relatively similar to kaolinite has been identified in illite
subject to artificial or natural irradiation. For the latter similar EPR signal were recorded in
naturally irradiated illite coming from alteration halos associated with Paleo-Proterozoic
uranium deposits in the Athabasca Basin in Canada (Allard et al. 2003; Morichon et al. 2008).
In both cases, in comparison with the extensive data available on kaolinite, the defects in
these illites tend to present a smaller thermal stability. In addition the EPR spectrum showed
very often a different look compared to kaolinite with a broader signal and very unclear
expression of the A, A’ and B centers corresponding to defects in the signal (Allard et al.
2012; Morichon 2008). Then it is critical to have a better understanding of the expression and
properties of radiation induced defects in illite, especially when old and long-lived open
geological systems are considered. In such systems numerous events ( e.g. thermal, multiple
radionuclide migrations) are superimposed over very long and short term periods from billons
years to the actual and illite can be considered as a natural dosimeter. So refinements in the
contribution of the short half life defects such as the A’ & B center in addition to the
permanent A center defects in the total RIDs content would be critical to decipher the radio-
elements migrations over time.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
206
The newly acquired data tends to make illite properties more similar to kaolinite than
previously thought, in term of spectra and stability properties. Then, addition to previous
authors work, we propose to revise and implement the knowledge of radiation induced defects
in illite. In this work a naturally irradiated illite formed in an unconformity related deposit
was studied with X & Q-bands hyperfrequencies on natural and annealed samples in order to :
(1) get a better estimation on the thermal stability of RIDs, (2) assess this stability throughout
geological times and (3) refine the spectrum signature, and assign to it the contribution of the
different defects centers. All these properties are critical to refine interpretations of the
radioelement’s mobility and its signature in clay minerals, as around uranium deposits for
both exploration and environmental considerations.
2.2. Sampling
Sample selection have been made in a larger data set of about 60 samples samples from illite
& sudoite rich alteration zones developed in the Woodburn lake Group, Archean volcano-
sedimentary sequence hosting unconformity related uranium mineralization, in the Kiggavik
area, Nunavut, Canada. The age of alteration related to the ore formation is yet relatively
poorly constrained within 1.2-1.4 Ga on historical illite K/Ar geochronological data (Mi ller et
al. 1989).
The majors’ constraints were to obtain a pure illite sample with a high concentration of
radiation defects in which the distinct components of the Electron Paramagnetic Resonance
spectrum are presents. This data screening (XRD followed by X-band EPR) lead to the
selection of the BG814 sample for further characterization of the Electron Paramagnetique
Resonance (EPR) signature of radiation induced defects in illite. The interest of this peculiar
sample is its strong and well defined defect spectra.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
207
2.3. Methods
All altered bulk rock samples were dispersed in deionzide water and the clay minerals
extracted by sedimentation in order to obtain the infra 4 micrometer size fraction. Clay
minerals identification and crystallographic properties were determined using X-ray
diffraction (XRD) on oriented slides and randomly oriented powders, following the
preparation methods given in (Brindley and Brown 1980). A D8 Advance Bucker
diffractometer equipped with a Cu anode was used for X-ray diffraction and analytical
conditions were set with a 40kV acceleration tension and 40mA current, and 1° fixed
divergence slit. Data collection scan parameters were 2-30 (oriented slides) or 19-30 (random
mounts) degrees 2theta both with a 0.01° 2theta step and 1 or 5 second counting time. In
addition to XRD, chemical analysis major elements using SEM-EDS on on clay pellets
separates were carried in order to recalculate the mineral proportion during sample selection
phase.
Electron paramagnetic resonance spectra of RID were observed at X- (≈ 9.βGHz) and Q-
bands (≈ 35GHz) and room temperature (20°C) using a Brucker EMXplusTM spectrometer on
both natural and annealed illite. The use of an higher frequency as in the Q-band allows lower
detection limits, and gives better resolved spectra by increasing the gap between spin levels
(Calas and Hawthorne 1988). The acquisition parameters were 1 G amplitude and a 327 ms
time constant and microwave power of 40mW in X-bands.
All spectrums were normalized to sample mass, volume occupied in resonance cavity and
acquisition gain. In addition EPR spectrums were labelled by their effective spectroscopic
factor g values defined by the follow formula: h * = g * β * Ho. The different parameters
being: h the Plack constant; the resonance frequency; g the Landé factor, a tensor with the
eigenvalues: gxx, gyy, gzz calibrated by comparison with a 2,2 diphenyl-1picrylhydrazyl
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
208
standard of known g value (gDPPH = 2.0036); β the Bohr magneton and Ho the external
magnetic field. The accuracy on magnetic field and g-values measurements were respectively
Ho = 1G, and g 0.001. It must be noted that only the g values can be compared due to
the frequency dependence of the magnitude and magnetic field positions of the resonances.
Concentrations are expressed in arbitrary units’ proportion to the number of spins per gram of
clay.
2.4. Annealing Experiments protocol
With a similar approach to the work carried on kaolinite step annealing was used in order to
differentiate RIDs in illite (Clozel et al. 1994). The isochronal annealing was carried out for 2
hours at 100°C intervals form 100 to 600°C, in order to define the thermal conditions for the
individualization of the different defects center spectra. In addition the lifetime of some of
the most stable defect centers were investigated with isothermal annealing experiments and
were performed at 400°C and 450°C from 30 minutes up to 134 hours. Regarding data on
kaolinite these center are thought to be stable over geological times under the Earth’s surface
thermal regime and then of great interest to trace ancient irradiations. Then illite could be
considered as a natural dosimeter.
A particular attention was given to the samples preparation for experiments in order to get
accurate and reproducible annealing temperatures. Each sample consists in a few 10s of
milligrams of illite, sieved at 50 micrometer and wrapped in aluminum foil and placed in a
regulated furnace equipped with a PID controller. Sampled were sieved a second time in order
to get randomly oriented powder in the Suprasil high purity silica glass capillaries used as
sample holder in the resonance cavity.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
209
2.5. Results
2.5.1. EPR parameters of defects in illite
As a first approach natural and annealed illites were studied in X-band in order to identify the
spectroscopic factors characteristic (g values) of the radiation induced defects in illite (A, A’
and B centers), figure 2-1a. Then, spectrums were obtained on natural illite and their
annealed equivalent to be able to identify the characteristic of the A center defects. In the
natural sample, 5 spectroscopic factors were identified respectively at 2.063, 2.050, 2.037,
2.013 and 2.002; while only 4 were present in the annealed illite at 2.063, 2.051, 2.011 and
2.002. It can already be noted that very little shift is present in the g-values positions between
the natural and annealed samples. In addition the intensity ratio of the bands doesn’t seems
affected by heating and the band at 2.063 could be very similar to the N1 defect described in
montmorillonite in term of g-value and annealing temperature around 500°C, figure 2-1b
(Sorieul et al. 2005). Finally the EPR signal for naturally irradiated illite from the Kiggavik
area shows similar spectroscopic parameters with a well expressed A center defect as well as
the presence of less stable ones in the 2.037 region possibly resulting from the superimposed
signal of the A’ and B centers.
Then, in addition to the illite EPR signal characterization, the stability and temperature
dependant kinetics of decay were experimentally tested by both isochronal and isothermal
annealing the latter being used to estimate the half life (t1/2) and the activation energy of Ea
(eV) of the A center defect in illite.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
210
Figure 2-1 : EPR spectra of defects in natural (a) and annealed illite (b) at X-Band (9.4GHz). DPPH (2,2
diphenyl-1picrylhydrazyl) is a standard compound with known g factor
2.5.2. Stability of the radiation induced defects in illite
First the stability of the radiation induced defects contents can be assessed using the overall
defect content via double integration of the EPR signal in complement to the defect spectra
evolution across the temperature range selected for annealing, Figure 2a & 2b. The annealing
curve, indicate a sharp decrease in both the defects content as well as a clear diminution of the
2.037 spectroscopic factor at low temperature below 100 °C. From then to around 350°C the
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
211
defects concentration is increasing by about 30% and is marked by a continuous decrease of
the 2.037 component and an increase of the 2.050, 2.011 and 2.002 g- values. Such behaviour
is similar to the one observed in kaolinite and various materials and due to electron transfers
during the annealing experiments (Griscom 1984; Hennig and Grün 1983). With increasing
annealing temperature the total defects concentration decreases sharply for temperature higher
than 450°C. Finally the total concentration evolution is a balance between at first below 400
°C the healing of the less stable with electron transfers phenomenon’s as a result of thermal
activation and in a second time the healing of the most thermally stable defects, which present
the g values characteristic of the center A type defects. Finally the A center appears to be
stable at until temperatures reaches field of clay mineral deshydoxylation temperature in
which the crystalline structure is affected. Then we propose to investigate the intrinsic
properties of these centers in illite via isothermal annealing experiments.
Figure 2-2 : Isochronal annealing experiments, 2hours from 100 to 600°C
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
212
Decay processes are generally described using first (Arrhenius) or second order equations
(Furetta 1988). The first order formula can be written: [A] = [A 0]e-Kt , where the different
parameters are: [A] is the instantaneous defect concentration (a.u.), [A0] the intial
concentration , t the time of decay and K the probability of decay per second. This probability
parameters itself is expressed by the following relation K = (t1/2)-1Ln2 = so.e
-Ea/kT, where s0 is
the frequency factor, usually in the range 108 - 1010 s-1 (Marfunin 1979), k the Boltzman
constant (k =8.6 10-5 eV.K-1) and T the temperature (K). Then it appears that the half life of
the defect in only temperature dependant and two isotherms would be required to determine
the activation energy. The second order decay law is more suitable for more complexes
mechanisms (transit stage or retrapping) that may occur during the decay processes, and can
be written as : [A] -1 = K.t+[A0] -1 with K = tgθ = (t1/2 . [A0])-1 = s0.e-Ea/kT or lnK= Ln s0-
(Ea/k)T-1 with θ is the slope of the linear curve. In this case the half life temperature and time
dependant.
Both first and second order equations were used to describe the isothermal annealing of the A-
center in illite. Curves were plotted for the BG814 sample in the figure 2-3, in which the
defect and the A center are particularly abundant. The decay curves, present two distinct
tends with at first a rapid decrease of the defects concentration within the first 8 hours of
annealing followed by a steady decreasing phases over the all annealing time span. Then, this
behaviour might be related to the healing of the least stable components of the defects signal,
as the A’ and B centers. Thereafter this rapid decay stage it can be assumed that the total
defect concentration represent the A center concentration. In both cases at 400 and 450°C
annealing temperatures, the second order law gives the best description of the data, figure 2-
3a. In addition the annealing curves, figures 2-3b, allowed the graphic determination of the
center-A properties with a maximal range of 1.9 to 49 109 years for the half life and activation
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
213
energies between 1.0 and 1.4 eV when estimation were made using both first and second
order decay laws, Table 2-1. Moreover, as the second order law tends to give the best data
description, the activation energy and half life at 15°C are a little bit lower than the ones
obtained on kaolinite but within similar orders of magnitude (Clozel et al. 1994).
Figure 2-3 : Isothermal annealing experiments at 400 and 450 isotherms. The decay law is described by a second
order kinetics. The fitting of the isotherms in the 1/[A] plot and the slope of the curves provides values of the
temperature dependant decay constant K(h-1). The activation energy and the half life are estimated and deduced
from decay equations.
a
b
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
214
Table 2-1 : A center properties, half life (years) and activation energy (eV) estimated at 15°C for both first and
second orders decay laws.
1st order 2nd order
s0(s-1) t1/2 @ 15°C t1/2 @ 15°C
108 3.9E+09 1.9E+09
1010 4.9E+10 2.9E+10
Ea (eV) 1.0 - 1.2 1.3 - 1.4
2.6. Preliminary discussion and concluding remarks
Additional electron paramagnetic resonance spectroscopy results in Q band couldn’t be
added to this final version of the manuscript. These new data will potentially allow a more
accurate identification of the radiation induced defects acciociated with illite and implement
the current results.
To date, the two major contributions form the present work are (1) the identification of a
singular EPR signal in naturally irradiated illite possibly linked to a type of radiation induced
defect specific to illite, and (2) the determination of the physical properties of such defect.
Thus, the radiation induce defects in illite seem similar to the A center defect, both in term of
EPR spectra and physical properties (e.g. stability), to the ones in kaolinite or
montmorillonite. This similarities could be explained by the nature of the defect and linked to
an electronic vacancy on a Si-O bond. Therefore, the type of sheet assemblage between the
tetrahedral and octaedral layers in the different clay minerals could have no influence on the
defect itself as the control for the decfect is a the atomic bond scale.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
215
Finally, the identification of defect stable at the scale of geological times (like center A
defect) as well as others less stable (A’, B centers) is critical to attempt to discriminate recent
and ancient radioelement circulations.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
216
2.7. References
Allard T, Ildefonse P, Del Villar LPr, Sorieul Sp, Pelayo M, Boizot B, Balan E, Calas G (2003) Radiation-induced defects in dickites from the El Berrocal granitic system (Spain): relation with past occurrence of natural radioelements. European Journal of Mineralogy 15:629-640.
Allard T, Balan E, Calas G, Fourdrin C, Morichon E, Sorieul S (2012) Radiation-induced defects in clay minerals: A review. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms 277:112-120. doi: http://dx.doi.org/10.1016/j.nimb.2011.12.044.
Brindley GW, Brown G (1980) Crystal structures of clay minerals and their X-ray identification. Mineralogical Society, London, UK.
Calas G, Hawthorne FC (1988) Introduction to spectroscopic methods. Reviews in Mineralogy and Geochemistry 18:1-9.
Clozel B, Allard T, Muller J-P (1994) Nature and stability of radiation-induced defects in natural kaolinites: new resulats and a reappraisal of published works. Clays and Clay Minerals 42:657-666.
Furetta C (1988) New calculations concerning the fading of thermoluminscent materials. Nucl Tracks Radiat Meas 14:413-414.
Griscom DL (1984) Characterization of three E'-center variants in X- and γ-irradiated high purity a-SiO2. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms 1:481-488. doi: http://dx.doi.org/10.1016/0168-583X(84)90113-7.
Hennig GJ, Grün R (1983) ESR dating in quaternary geology. Quaternary Science Reviews 2:157-238. doi: http://dx.doi.org/10.1016/0277-3791(83)90006-9.
Marfunin AS (1979) Spectroscopy, Luminescence and Radiation Centers in Minerals. Springer Verlag, Berlin, Heidelberg, New York.
Miller AR, Cumming GL, Krstic D (1989) U-Pb, Pb-Pb, and K-Ar isotopic study and petrography of uraniferous phosphate-bearing rocks in the Thelon Formation, Dubawnt Group, Northwest Territories, Canada. Canadian Journal of Earth Sciences 26:867-880.
Morichon E (2008) Les défauts d'irradiation dans les minéraux argileux: des marqueurs de la mobilité de l'uranium dans le contexte des gisements d'uranium associés à une discordance. Thèse Université de Poitiers, pp 297.
Morichon E, Allard T, Beaufort D, Patrier P (2008) Evidence of native radiation-induced paramagnetic defects in natural illites from unconformity-type uranium deposits. Phys Chem Minerals 35:339-346. doi: 10.1007/s00269-008-0227-5.
Sorieul S, Allard T, Morin G, Boizot B, Calas G (2005) Native and artificial radiation-induced defects in montmorillonite. An EPR study. Phys Chem Minerals 32:1-7. doi: 10.1007/s00269-004-0427-6.
Nature and stability of radiation induced defects in natural illite new results and implications for ancient radioelement mobility
217
C. DISCUSSION GÉNÉRALE, CONCLUSIONS ET PERSPECTIVES
Discussion générale
218
1. Discussion générale
La genèse d’un gîte métallique implique la succession d’une série d’étapes de pré-
concentration, libération, transport, dépôt et enfin de préservation des minéraux formant le
minerai d’intérêt économique. Les gisements d’uranium associés aux discordances du
Protérozoïque s’inscrivent eux aussi dans ce schéma, depuis les processus de différenciation
magmatique à l’origine des sources primaires de l’uranium, aux divers processus superficiels
qu’ils soient sédimentaires, diagénétiques ou hydrothermaux à l’origine des concentrations
économiques d’uranium (Cuney 2010). L’ensemble des données acquises à l’échelle du
faisceau structural de Kiggavik-Andrew Lake dans ce travail permet d’identifier certaines de
ces étapes et processus.
On peut replacer la formation des minéralisations en uranium de la bordure Sud-Est du bassin
Protérozoïque moyen du Thelon dans un cadre métallogénique plus large à l’échelle du
bouclier Canadien. Il s’agira tout d’abord de retracer l’histoire des altérations ayant
successivement affecté le district de Kiggavik afin de comprendre comment elles ont pu
contribuer, par incrément, à la formation des minéralisations en uranium. Cela amènera à
considérer les conditions physico-chimiques à l’origine des signatures minéralogiques propres
à chaque environnement, en considérant ses implications en termes de source, transport ou de
piège de l’uranium. Enfin l’ensemble sera replacé dans le contexte géodynamique global
ayant conduit à la formation des bassins intracontinentaux hôtes des minéralisations et
contraint du point de vue temporel à l’aide d’éléments de géochronologie.
Au vu des données présentées dans ce mémoire, il est possible de proposer un schéma
retraçant l’évolution géologique de la zone de Kiggavik au cours de la vaste période (1800-
1100Ma) qui couvre l’histoire de cette région, de l’initiation du processus sédimentaire lié à la
mise en place du bassin du Thelon à la fin des épisodes d’altération argileuse associés à la
Discussion générale
219
mise en place ou au remaniement de la minéralisation uranifère Figure 1-2. Enfin, chacune
des étapes sera mise en parallèle avec les connaissances actuelles des gisements du bassin
Meso Proterozoique de l’Athabasca qui constitue une référence en termes de gisement
d’uranium associé à une discordance Paléoprotérozoique.
1.1. Histoire des événements d’altération
On peut tout d’abord noter que la mise en place des minéralisations s’inscrit principalement
dans le cycle orogénique Hudsonien. On peut alors mettre en parallèle les différents
événements d’altération et les grands événements géologiques ayant affecté la zone de
Kiggavik, depuis les événements tardi-orogéniques Hudsonien jusqu’à la mise en place des
minéralisations uranifères.
1.2. Evénements précoces Hudsoniens
Ils regroupent à la fois les réactivations des grandes structures crustales Archéennes lors de
l’orogenèse Husdonienne ainsi que tous les stades post-orogéniques. Il s’agit à la fois de la
rétromorphose dans le faciès schiste vert des roches du socle métamorphique de la zone de
Kiggavik et de la mise en place d’un système de veines de quartz de haute température
soulignant les failles régionales Est-Ouest. Elles sont identifiées dans la zone d’End Grid dans
cette étude, mais aussi dans le gisement d’Andrew Lake (Pagel and Ahamdach 1995). On peut
aussi rattacher à ces épisodes tardi- métamorphiques les évidences d’altération propylitique
exprimée sous la forme de veinules d’épidotes et/ou d’adulaire localement. Cette
structuration, permet de mettre en place les grandes discontinuités qui pourront par la suite
être réactivées et former les principaux drains empruntés par les fluides minéralisateurs qui
contrôlent la localisation des minéralisations (Annesley et al. 1995; Annesley et al. 1996;
Beaudemont and Fedorowich 1996). De plus la mise en place des corridors brêchiques à
remplissage de quartz, contribue à créer des zones de contraste rhéologiques, qui seront
importantes pour contrôler l’ouverture des discontinuités (zone mylonitique, foliation) ou des
Discussion générale
220
fractures. Dans le bassin de l’Athabasca de nombreux gisements d’importance économique
sont eux aussi situés aux interfaces entre deux lithologies aux propriétés mécaniques
contrastées. Parmi ceux-ci, on peut citer les dômes de gneiss au contact des roches supra-
crustales de la ceinture de Wollaston (Yeo and Delaney 2007), de même que le contraste
existant entre les quartzites et les autres métasediments, parfois graphitiques, de cette ceinture
de plis et chevauchements.
A cette structuration s’ajoutent les phénomènes propres à l’effondrement de l’orogène
Hudsonien tel que la genèse de granites peralumineux par le biais de la fusion crustale lors de
la phase d’extension post orogénique, puis la mise en place des syénites et des granites
anorogéniques de la suite Nueltin (Van Breemen et al. 2005; Peterson et al. 2002).
Figure 1-4 : Rapport Th/ U des intrusions Hudsoniennes et Nueltin, d’après Van Breemen, β005
Les phases de fusion crustale de roches alumineuses permettent par ailleurs d’aboutir à des
roches plus différenciées et ainsi enrichir la croûte en uranium, comme c’est le cas dans l’Est
du bassin de l’Athabasca (Annesley and Madore 1999). Toutefois il semble que tous les
Discussion générale
221
granites Hudsonien ne soient pas tous aussi fertiles en uranium (Van Breemen et al. 2005),
Figure 1-1. Le granite de Kiggavik entre dans cette catégorie de granite faiblement fértile
(Weyer et al. 1987). Toutefois, et à contrario de ce qui est observé dans l’Est du bassin de
l’Athabasca, on ne retrouve pas d’évidence de pegmatites à uraninite à Kiggavik. Cette
fertilité moindre peut s’expliquer par une différence de nature des protolithes, les
métasédiments pélitiques du Wollaston étant plus riches en uranium que les séries de l’Amer
ou du Ketyet River Group, principalement constituées de quartzites et d’arkoses. Par ailleurs,
les métagraywackes de la ceinture de roche verte du Woodburn lake Group sont
particulièrement pauvres en U (<3 ppm U).
Dès le stade Hudsonien, il apparaît donc, des différences marquées entre le bassin
d’Athabasca et la bordure Sud Est du bassin du Thelon en ce qui concerne le potentiel
métallogénique des protores pour alimenter des gisements liés à la discordance bassin-socle.
Dans la région de Kiggavik, les sources de l’uranium pourraient être reliées aux tuffs
ryholitiques du groupe de Wharton déposés lors de la mise en place du bassin de Baker Lake.
Ceux-ci pourraient avoir formé alors une source régionale associée ponctuellement à des
sources « plutoniques » plus locales tels que les granitoïdes et les syénites du socle.
Discussion générale
222
Discussion générale
223
Figure 1-5 : Reconstitution schématique de l’évolution des processus géologiques dans les roches situées au
voisinage de la discordance paleoprotérozoïque dans la zone de Kiggavik.
1.3. Mise en place du profil d’altération Pré-Thélon
L’existence d’un régolithe ayant transformé la partie superficielle des roches du socle avant
la mise en place des premiers sédiments silcoclastiques des bassins de l’Athabasca et du
Thelon a été évoquée par de nombreux auteurs sur la base d’évidence minéralogiques
(kaolinite, diaspore, hematite, phosphate sulfates d’aluminium hydratés) et pétrographiques
(Macdonald 1980; Pagel 1975; Cecile 1973). Les études pétrographiques et minéralogiques
présentées dans ce mémoire démontrent que tous les minéraux index des altérites
continentales de type latérite ou bauxite sont présents dans la matrice sédimentaire des
premiers remplissages de conglomérats et de grès grossiers qui subsistent dans la région de
Kiggavik (kaolinite riches en fer, hématite, oxy-hydroxydes d’aluminium, oxydes de cérium
et de thorium, ainsi que des phosphate-sulfate d’aluminium). Ces observations nous
conduisent à interpréter ces premières formations sédimentaires comme des produits issus de
l’érosion et démantèlement de la surface régolithisée des roches métamorphiques et
magmatiques environnantes. La très faible concentration en uranium des premiers dépôts
sédimentaires qui ont été préservés de l’altération hydrothermale (0,3 à 0,7 ppm) suggère une
mobilité précoce du stock potentiel d’uranium issu des processus de régolithisation des roches
du socle. Dans l’état d’avancement de nos connaissances sur les transferts géochimiques
effectifs pendant la phase de sédimentation précoce du bassin du Thelon à Kiggavik, il semble
prématuré d’établir un lien entre l’uranium mobilisé pendant ce phénomène précoce et les
corps minéralisés actuels. On peut cependant mentionner des résultats préliminaires de
travaux de spectroscopie de résonance paramagnétique électronique sur la kaolinite des
formations sédimentaires basales du bassin du Thelon qui indiquent des concentrations de
défauts d’irradiation élevées dans la région de Kiggavik qui ne sont pas en accord avec les
Discussion générale
224
concentrations actuelles en radio-éléments. De tels défauts pouvant être la conséquence du
passage de fluides riches en radioélements comme cela a déjà été démontré dans le bassin
d’Athabasca (Morichon 2008; Morichon et al. 2008; Morichon et al. 2010). Des travaux
complémentaires seront nécessaires pour évaluer l’importance de ces migrations qui ont dû se
produire a un stade très précoce de l’histoire du bassin du Thelon, avant la cimentation des
grès et le confinement de l’ensemble des minéraux détritiques par le quartz microcristallin.
1.4. Diagenèse et évolution du bassin du Thelon
Dans le continuum d’évolution des bassins intracratoniques Protérozoïques, l’histoire
diagénétique apparait prolongée pour aboutir à des conditions de diagenèse poussée (Patrier et
al. 2003; Beaufort et al. 2005; Jefferson et al. 2007). La profondeur maximale
d’enfouissement est alors estimée à environ 5km sur la base de données d’inclusions fluides
(Pagel 1975) ou du stade de transformation en dickite des minéraux du groupe kaolin
(Beaufort et al. 1998; Lanson et al. 2002). Cette évolution permet aux saumures de bassins
oxydantes de remobiliser et transporter l’uranium en solution. Les données nouvellement
acquises sur l’ordre/désordre, des kaolinites recristallisées de la base du bassin ainsi que les
fractures à dickite indiquent également que dans la zone de Kiggavik les formations basales
du bassin du Thelon ont subi un enfouissement similaire à ce qui a été évoqué dans le bassin
d’Athabasca ou bien même dans les grès de Kombolgie en Australie (environ 5km ). De plus,
on peut noter que les inclusions fluides triphasées à cube de halite observées dans les veines
de quartz et surtout les dolomites du socle indiquent des paléotempératures aux alentours de
200 °C qui sont en accord avec la transition complète de la kaolinite en dickite dans les roches
gréseuses comme cela a été observée dans les grès de Kombolgie (Patrier et al., 2003) et des
salinités semblables à celles des saumures minéralisatrices connuesdans le bassin de
l’Athabasca (Derome 2002; Pagel and Jaffrezic 1977).
Discussion générale
225
Certaines caractéristiques des grès telles que les ciments phosphatés (Gall and Donaldson
2006), ainsi que les surcroissances de quartz (Hiatt et al. 2003; Hiatt et al. 2010) ou la
présence de feldspaths potassiques néoformés (Renac et al. 2002) n’ont pas été retrouvées
dans cette étude. On doit néanmoins prendre en compte le fait que ces travaux ne concernent
que les roches sédimentaires de la base des grès du Thelon. Les ciments phosphatés ou les
illites qui ont été mentionnés plus haut dans la série sédiementaire du bassin du Thélon par
ailleurs peuvent avoir été érodés. La préservation de kaolinite détritique non illitisée dans les
grès situés à la base du bassin n’est pas limitée à Kiggavik. En effet, celle-ci a déjà été mise
en évidence à la base du bassin de l’Athabasca, dans la région de Shea Creek (Uri 2012).
Enfin, les températures calculées à partir de la composition isotopique de l’oxygène des illites
néoformées des grès du Thelon par ces mêmes auteurs sont cohérentes avec celles obtenues à
Kiggavik dans le halo d’altération associé à la minéralisation de Bong (Sharpe 2013). Elles se
situent aux alentours de 200°C, en cohérence avec les données microthermométriques de
notre étude. Il est alors envisageable que la partie basale du bassin du Thelon étudiée dans la
zone de Kiggavik appartienne à un compartiment du bassin qui a été préservé de l’altération
hydrothermale à illite et sudoite. Ce type de compartiment se révèle très intéressant pour
recueillir des informations originales sur l’histoire précoce (sédimentaire puis diagénétique)
qui a précédé l’évènement d’altération hydrothermale régionale auquel sont associés les
gisements d’uranium qui sont présents dans les roches de socle.
1.5. Altération hydrothermale et mise en place de la minéralisation
La prise en compte des saumures et de leur température amène naturellement à considérer leur
interaction avec les roches du socle sous la discordance du Thelon, là où sont encaissées les
minéralisations en uranium. De manière générale, ces interactions fluides/roche sont
marquées par la déstabilisation des aluminosilicates et des sulfures du socle avec une
précipitation concomitante de l’illite et de l’uraninite. On comprend alors que les lithologies
Discussion générale
226
plus riches en phyllosilicates sensibles au redox (donneurs d’électrons comme l’oxydation du
fer des phyllosilicates (chlorite-Fe ou de la biotite) et des sulfures (pyrite) puissent agir en tant
que piège de la minéralisation au cours de leur altération, comme c’est le cas dans les méta-
sédiments du Woodburn Lake Group. Le contrôle de la minéralisation apparaît alors local
guidée par la richesse de l’encaissant en phyllosilicates ferreux ou en pyrite. De plus, les
matières carbonées en relation avec les phénomènes d’altération peuvent localement
consittuer des pièges supplémentaires efficaces. Les teneurs mesurées de plusieurs pour cent
métal dépassant largement la moyenne de celle des gisements de la zone de Kiggavik.
L’étude de l’altération sur l’ensemble des gisements du faisceau structural de Kiggavik-
Andrew Lake a permis de mettre en évidence une séquence paragenétique d’altération
commune à l’ensemble de zones minéralisées. Elle s’exprime de manière analogue à celle des
gisements de type discordance de l’Athabasca ou de la Kombolgie par un mélange d’illite et
de sudoite et la présence de phases accessoires comme les APS ou les matières carbonées. On
notera l’absence de la dravite qui est souvent un minéral index abondant dans de nombreux
gisements associés aux discordances du bassin d’Athabasca et plus accessoire dans les
gisements de Kombolgie. Ces volumes de roches hydrothermalisées forment des halos
d’altération qui sont contrôlés par les discontinuités structurales à toute échelle : les réseaux
de failles et leurs zones d’endommagement, les fractures, mais aussi les plans de foliation des
métasédiments à plus petite échelle. Il apparaît alors un double contrôle à la fois
litholologique et structural pour la précipitation de la minéralisation. On peut aussi remarquer
que la minéralisation peut être également présente dans des secteurs situés en périphérie des
grands drains là où l’altération de la roche encaissante est modérée et où persistent une partie
des minéraux porteurs de fer ferreux (progression des fronts rédox lors des phases de
minéralisations primaire mais aussi des remobilisations). Ainsi, et compte tenu de la position
des minéralisations rencontrées dans le socle à jusqu'à plusieurs centaines de mètres en
Discussion générale
227
dessous de la surface d’érosion actuelle qui se situe à une profondeur indéterminée sous la
discordance paleoprotérozïque, il semble très probable que les minéralisations du faisceau de
Kiggavik représentent l’extension en profondeur (voir les racines ?) d’un système de
minéralisation en uranium de type discordance tel que ceux déjà connus par ailleurs dans le
monde (Athabasca, Kombolgie…).
Un tel contexte géologique pourrait expliquer à la fois les plus faibles teneurs en uranium,
ainsi que le caractère disséminé de la minéralisation, comparativement à celle connue au
voisinage de la discordance dans le bassin de l’Athabasca et des caractéristiques plus proches
de celles rencontrées dans les gisements australiens plus profonds de Kombolgie tels que celui
de Jabiluka notamment (Jefferson et al. 2007). On ne peut de ce fait pas exclure que des
minéralisations aient été ou soient présentes au niveau de la discordance par ailleurs dans le
bassin du Thelon. Dans un tel schéma, la précipitation de l’uranium en solution est
conditionné par la neutralisation et la reduction progressive du fluide minéralisateur du fait
de son interaction avec les minéraux des roches de socle (Komninou and Sverjensky 1996).
Les derniers progrès réalisés sur l’interprétation des défauts d’irradiation de l’illite sont
primordiaux pour tenter de reconstruire les paléo-circulations des radioéléments au travers des
drains empruntés par les saumures oxydantes. La meilleure connaissance des signaux associés
aux différents types de défauts électroniques devrait permettre de différencier les irradiations
les plus anciennes, de celle plus récentes liées à des remobilisations des minéralisations
actuelles.
Conclusion générales et perspectives
228
2. Conclusion générales et perspectives
L’ensemble des travaux menés dans cette thèse ont permis d’affiner la compréhension du
système d’altération associé aux minéralisations en uranium du faisceau structural de
Kiggavik en le reliant à l’expression profonde d’un système de type discordance tel que ceux
déjà connus dans le bassin d’Athabasca au Canada et ceux de Kombolgie en Australie. Par
certains aspects, les minéralisations de socles reconnues à Shea Creek dans le bassin
d’Athabasca plus au sud pourraient constituer un contexte de dépôt proche de celui caractérisé
vers la marge Sud Est du bassin du Thelon. Compte tenu du type de minéralisation la
perspective de découvertes de minéralisations, dans les grès ou à la discordance basale de la
formation du Thelon ne peut pas être exclue. On peut par ailleurs mentionner que l’altération
dans les grès peut apparaître localement, la transition entre les roches altérées ou non pouvant
être réalisée en quelques centaines de mètres. Ainsi l’absence d’altération dans les grès au
dessus de la discordance n’interdit pas que des zones altérées, et donc indicatices d’un
potentiel pour l’exploration soit présente dans le socle sous jacent.
Les relations entre la circulation des fluides minéralisateurs et les structures fertiles sont en
cours d’étude par le biais de l’étude des défauts d’irradiations de l’illite qui est un minéral
ubiquiste dans les roches du socle. Un complément de travail de géologie structurale associée
à de la radiogéochronologie sur les minéraux argileux devraient permettre de mieux
contraindre la succession des événements d’altération et minéralisations.
Par ailleurs, des études de la chimie des inclusions fluides par ablation laser couplée à la
spectrométrie de masse pourraient permettre de donner des indications supplémentaires sur la
composition des saumures et sur leur signature géochimiques.
Références
229
3. Références
Annesley I, Madore C, SHi R (1995) Revision mapping/integrated geology Wollaston EAGLE project:
Segment 1. Saskatchewan Research Council, Saskatoon, pp 132. Annesley I, Madore C, SHi R (1996) Wollastion EAGLE project, Revision mapping/integrated geology
Wollaston EAGLE project:Segment 2. Saskatchewan Research Council, Saskatoon, pp 184. Annesley I, Madore C (1999) Leucogranites and pegmatites of the sub-Athabasca basement,
Saskatchewan: U protore? In: Stanley CJ (ed) Mineral Deposits:Processes to Processing. Balkema, pp 297-30
Beaudemont D, Fedorowich J (1996) Structural control of uranium mineralization at the Dominique-Peter deposit, Saskatchewan, Canada. Economic Geology 91:855-874.
Beaufort D, Cassagnabère A, Petit S, Lanson B, Berger G, Lacharpagne JC, Johansen H (1998) Kaolinite-to-dickite reaction in sandstone reservoirs. Clays minerals 33:297-316.
Beaufort D, Patrier P, Laverret E, Bruneton P, Mondy J (2005) Clay Alteration Associated with Proterozoic Unconformity-Type Uranium Deposits
in the East Alligator Rivers Uranium Field, Northern Territory, Australia. Economic Geology v. 100:pp. 515–536.
Cecile MP (1973) Lithofacies analysis of the Proterozoic Thelon Formation, Northwest Territories. Carlton University, pp 119.
Cuney M (2010) Evolution of Uranium Fractionation Processes through Time: Driving the Secular Variation of Uranium Deposit Types. Economic Geology 105:553-569. doi: 10.2113/gsecongeo.105.3.553.
Derome D (2002) Evolution et origines des saumures dans les bassins protérozoiques au voisinage de la discordance socle/couverture. L'exemple de l'environnement des gisements d'uranium associés aux bassins Kombogie (Australie) et Athabasca (Canada). Université Henri Poincaré, Nancy.
Gall Q, Donaldson JA (2006) Diagenetic fluorapatite and aluminum phosphate-sulphate in the Paleoproterozoic Thelon Formation and Hornby Bay Groupe, northwestern Canadian Shield. Canadian Journal of Earth Sciences 43:617-629.
Hiatt EE, Kyser K, Dalrymple RW (2003) Relationships among sedimentology, stratigraphy, and diagenesis in the Proterozoic Thelon Basin, Nunavut, Canada: implications for paleoaquifers and sedimentary-hosted mineral deposits. Journal of Geochemical Exploration 80:221-240.
doi: http://dx.doi.org/10.1016/S0375-6742(03)00192-4. Hiatt EE, Palmer S, E., Kyser K, O'Connor T (2010) Basin evolution, diagenesis and uranium
mineralization in the Paleoproterozoic Thelon Basin, Nunavut, Canada. Basin Research 22:302-323.
Jefferson CW, Thomas DJ, Gandhi SS, Ramaekers P, Delaney G, Brisbin D, Cutts C, Portella P, Olson RA (2007) Unconformity-associeted uranium deposits of the Athabasca Basin, Saskatchewan and Alberta EXTECH IV. pp 23-67.
Komninou A, Sverjensky DA (1996) Geochemical modeling of the formation of an unconformity-type uranium deposit. Economic Geology 91:590-606. doi: 10.2113/gsecongeo.91.3.590.
Lanson B, BEAUFORT D, Berger G, Bauer A, Cassagnabère A, Meunier A (2002) Authigenic kaolin and illitic minerals during burial diagenesis of sandstones: a review. Clay Minerals 37:1-22.
Macdonald R (1980) Mineralogy and geochemistry of a Precambrian regolith in the Athabasca Basin. University of Saskatchewan, Saskatoon, pp 151.
Morichon E (2008) Les défauts d'irradiation dans les minéraux argileux: des marqueurs de la mobilité de l'uranium dans le contexte des gisements d'uranium associés à une discordance. Thèse Université de Poitiers, pp 297.
Références
230
Morichon E, Allard T, Beaufort D, Patrier P (2008) Evidence of native radiation-induced paramagnetic defects in natural illites from unconformity-type uranium deposits. Phys Chem Minerals 35:339-346. doi: 10.1007/s00269-008-0227-5.
Morichon E, Beaufort D, Allard T, Quirt D (2010) Tracing past migrations of uranium in Paleoproterozoic basins: New insights from radiation-induced defects in clay minerals. Geology 38:983-986. doi: 10.1130/g31453.1.
Pagel M (1975) Détermination des conditions physico-chimique de la silicification diagénétique des grès Athabasca (Canada) au moyen des inclusions fluides. Comptes Rendus de l'académie des Sciences Paris 280:2301-2304.
Pagel M, Jaffrezic H (1977) Analyses chimiques des saumures des inclusionsdu quartz et de la dolo ite du gise e t d’u a iu de Ra it Lake Ca ada . Aspe t éthodologi ue et importance génétique. Comptes Rendus de l'Académie des Sciences 284:113-116.
Pagel M, Ahamdach N (1995) Etude des inclusions fluides dans les quartz des gisements d'uranium de l'Athabasca et du Thelon (Canada). Centre de Recherche sur la Geologie des matières premieres minerales et énérgétiques - CREGU, Vandoeuvre les Nancy, pp 1-10.
Patrier P, Beaufort D, Laverret E, Bruneton P (2003) High diageentic dickite and 2M1 illite from the middle Proterozoic Kombolgie formtion (Northern Territory, Australia). Clays and Clay Minerals 51:102-116. doi: 10.1346/ccmn.2003.510112.
Peterson TD, Van Breemen O, Sandeman H, Cousens B (2002) Proterozoic (1.85-1.75 Ga) igneous suites of the Western Churchill Province: granitoid and ultrapotassic magmatism in a reworked Archean hinterland. Precambrian Research 119:73-100.
Renac C, Kyser K, Durocher K, Dreaver G, O'Connor T (2002) Comparison of diagenetic fluids in the Proterozoic Thelon and Athabsca Basins, Canada: implications for protracted fluid histories in stable intracratonic basins. Can J Earth Sci 39:113-132.
Sharpe R (2013) The geochermistry and geochronolgy of the Bong uranium deposit, Thelon Basin, Nunavut, Canada Department of Geological Sciences. University of Manitoba, Winnipeg, Manitoba.
Uri F (2012) Altération et minéralisation d'uranium à Shea Creek (Ouest Athabasca, Saskatchewan, Canada) : vers un nouveau modèle génétique de gisement. Université de Poitiers pp 338.
Van Breemen O, Peterson TD, Sandeman H (2005) U-Pb zircon geochronology and Nd isotops geochemistry of Proterozoic granitoids in the western Churchill Province: intrusive age pattern and Archean source domains. Canadian Journal of Earth Sciences 42:339-377.
Weyer H-J, Friedrich G, Bechtel A, Ballhorn RK (1987) The Lone Gull uranium deposit-New geochemical and petrological data as evidence for the nature of the ore bearing solutions Metallogenesis of uranium deposits. IAEA, Vienna.
Yeo G, Delaney G (eds) (2007) The Wollaston supergroup stratigraphy and metallogeny of a Paleoproterozoic Wilson cycle in the Trans-Hudson orogen, Saskatchewan. Geological Survey of Canada.
Annexe
Méthodologie
Comme précédemment évoquées, de nombreuses méthodes ont pu être mises en œuvre afin
de répondre aux objectifs de ce travail. Afin de rendre la lecture de ce manuscrit plus claire, et
pour donner le supplément de détail qui fait parfois défaut par souci de concision dans les
articles, une rapide revue des méthodes utilisées sera donnée. Il s’agira de présenter pour la
spectroscopie en résonance paramagnétique électronique ou la sonde ionique, l’objet de sa
mise en œuvre en rappelant son grand principe de fonctionnement en faisant un éventuel
rappel à la théorie, et insistant pour certaines d’entre elles sur la méthodologie de traitement
des données acquises.
La caractérisation des milieux géologiques passe par un ensemble de sauts d’ échelles
d’observations et de mesures, de l’affleurement à la roche, agrégat de minéraux, puis aux
minéraux eux-mêmes et enfin leur organisation spatiale ou leur composition isotopique. Ainsi
à la fois chimie et cristallographie sont mobilisées pour identifier, comprendre et interpréter
leur relation texturales et in fine tenter de proposer une interprétation de l’histoire géologique.
A cela s’ajoute la contrainte temporelle afin d’ancrer les successions relatives des événements
dans un l’échelle absolue des temps géologiques.
Spectroscopie de résonance paramagnétique électronique
Généralités
La spectroscopie RPE (Résonance Paramagnétique Electronique) s’apparente à la RMN mais
il s’agit alors de s’intéresser au comportement des électrons non appariés présent dans le
média à analyser, en utilisant les transitions énergétiques entre différents niveaux d’énergie de
spin électronique. Cette méthode de caractérisation d’une grande sensibilité, de l’ordre de la
partie par million (ppm) en concentration s’apparente à de la dosimétrie. Ainsi les défauts
induits par l’irradiation, principalement du aux particules alpha, permettent alors de tracer
les circulations des radioéléments en solution au cours de l’histoire géologique du système
considéré.
Deux appareils ont été utilisés, un spectromètre ESP 300E Bruker mais surtout son équivalent
plus moderne, l’EMXplusTM, offrant à la fois une interface souple sous windows 7 ainsi
qu’une plus grande sensibilité de la cavité de résonance, Figure 1. Le principe de
fonctionnement étant quoi qu’il en soit le même. Les éléments constitutifs sont :
- L’électroaimant pour imposer le champ Ho
- La cavité de résonnance dans laquelle on introduit l’échantillon
- Le pont hyperfréquence (diode de type Gunn) qui génère une onde électromagnétique
de fréquence fixe à 9.4 GHz en bande X
- Un détecteur pour mesure les ondes électromagnétiques
- Ordinateur de contrôle pour paramétrer les conditions analytiques et d’exporter les
spectres acquis
- Système d’échange de chaleur pour le refroidissement du pont et de l’électroaimant.
Figure 1 , Spéctromètre RPE, source de microonde (1) & électroaimant (2) et son alimentation (3), cavité de résonance (4)
Théorie
Les conditions de résonance
Sous l’influence d’un champ magnétique Ho l’électron de moment magnétique µ s’aligne sur
l’axe du champ. Son moment angulaire propre, aussi appelé spin, est lui caractérisé par son
nombre quantique S=1/β. L’énergie d’interaction entre le champ appliqué et le moment
magnétique de l’électron s’écrit alors :
E = g * * Ms * Ho
Avec :
- le magnéton de Bohr, égal à eh/βmc - g le facteur spectroscopique de l’électron libre - Ms la projection du spin sur l’axe Ho
2
1
3
image: www.bruker.com
4
L’effet Zeeman, à pour effet de produire des transitions électroniques de niveau d’énergie
déterminées par les deux orientations possible du spin, donnant un état de basse et de haute
énergie (E= 1/2*g* *Ho), selon que le spin est parallèle ou antiparallèle au champ
magnétique externe.
Les conditions de résonances sont alors obtenues en utilisant une source de micro-ondes
constante (de fréquence =9.4 GHz pour la bande X) dans un champ magnétique variable. Il
est alors possible de mesurer l’absorption induite du quantum d’énergie résultant de la
transition de niveaux d’énergie à la condition de résonnance.
On peut l’exprimer par l’expression suivant :
h * = g * * Ho
Avec :
- h la constante de Planck
- la fréquence des microondes - g le facteur de Landé, spécifique du type de défaut dont les valeurs dépendent des
directions cristallographiques - le magnéton de Bohr - Ho le champ magnétique externe
Les types de défauts d’irradiation et leur genèse
Dès lors que les bases physiques théoriques sont posées, il faut maintenant considérer les
différents types de défauts et les conditions de leur formation et plus important encore leur
persistance dans le temps au sein du minéral.
Type de défaut Nature Stabilité T1/2 années T de (recuit °C) Kaolinite/Illite/Sudoite
Centre A Si-O□ 1012 450 / 600 / 500
Centre A' Si-O□ 103 300
Centre B Al-O□-Al 10-100 200
D’après (Calas et al. 2003; Allard et al. 2012)
Figure 2, type de défaut d'irradiation (Allard et al. 2012)
Les défauts de centre A, les plus stables à l’échelle des temps géologiques, sont ceux
responsables de la majeure partie du signal d’irradiation que l’on peut mesurer en RPE. La
création du défaut peut être induite par tous types de radiation α, , et γ, mais elle nécessite
toutefois la présence d’une substitution (d’un cation trivalent par un cation divalent) créant
un déséquilibre local de charge qui sera par la suite compensé par l’éjection d’un électron lors
de l’interaction matière particule (Jones et al. 1974).
Mise en œuvre et calcul des concentrations en défaut
L’acquisition des données est réalisée sur des extraits argileux purs pour (1) réduire les pertes
de signal par effet de dilution, si par exemple du quartz est présent dans l’échantillon la
quantité de défaut mesurée sera normalisée à 100% d’argile et (2) éviter la présence de
minéraux porteurs de Fe2+/3+ qui peuvent perturber le signal RPE.
Les échantillons sont tamisés (maille 50 microns) afin d’obtenir une orientation aléatoire des
feuillets dans le tube en silice ultra pure qui contient l’échantillon.
Les spectres de défauts sont réalisés sur une gamme de champs magnétiques comprise entre
3100 et 3600 Gauss (soit 310 et 360 mT, 1Tesla = 10 000 Gauss) pour une puissance du pont
hyperfréquence de 40mW. Une phase de post traitement et de correction du signal tenant
compte de la quantité de matière présente dans le tube (en masse, et en hauteur par rapport à
la longueur utile de la cavité) et du gain utilisé pour l’acquisition est alors nécessaire.
Le calcul de la concentration en défaut de l’échantillon passe par le traitement du signal avec
le logiciel Kaleidagraph, il s’agit de corriger le signal de la ligne de base et de procéder à
deux intégrations successives. L’aire sous la courbe de la seconde intégrale donne alors la
quantité de défauts pour un échantillon en unités arbitraires, figure 2. Le passage en unités
absolues est alors aisé après étalonnage de la cavité avec un standard xxx en utilisant la
formule donnée par (Wertz and Bolton 1986) :
Avec :
- (Std) concentration en défaut dans l’étalon
- Sx surface sous la courbe (2nd intégration) pour l’échantillon
- Sstd surface sous la courbe (2nd intégration) pour l’étalon
- Pasx / Passtd pas du spectre de l’échantillon / de étalon
- Gx gain de l’échantillon ; Gstd gain de l’étalon
- gx facteur spectroscopique caractéristique du type de défaut
- gstd facteur spectroscopique du standard
- Px /Pstd puissance de l’échantillon / du standard
Figure 2, séquence schématique du traitement des spectres RPE pou la uantification des défauts d’i adiations
SIMS (Secondary Ion Mass Spectrometry)
Généralités
La spectrométrie de masse à ionisation secondaire permet entre autre l’analyse ponctuelle, in
situ, des rapports isotopiques. Initialement développée à l’Université d’Orsay par G. Slodzian
dans les années 1960 pour l’étude des matériaux, elle s’avère d’une grande utilisé pour les
géosciences ou son utilisation à pris un véritable essor aussi bien pour la datation (U/Pb) que
pour la détermination des rapports isotopiques d’éléments stables (O, H, S). Elle permet de
s’affranchir des problèmes de séparations ou de purifications des différentes phases (parfois
techniquement impossible). Ainsi comme pour la microsonde électronique et la chimie des
minéraux, on accède alors à des données isotopiques que l’on peut mettre en regard
d’information pétrographiques à une échelle plus petites que celle des minéraux (Reed 1990;
Reed 1989). On peut évoquer pour l’exemple l’évolution de la composition isotopique de
l’oxygène des fluides entre plusieurs phases de surcroissances, la mise en évidence d’âges
distincts entre différentes plages de grains de zircons, de monazite ou d’uraninite permettant
ainsi de mieux caler dans le temps l’histoire des cristallisations.
Un photographie ainsi qu’un schéma de l’appareil correspondant est présenté sur la figure 3a
et 3b.
Figure 3, A SIMS CAMECA IMS7f, Université du Manitoba SIMS Facility, B schéma de fonctionnement (CAMECA IMS 6f)
Sources archives CAMECA
A
B
Théorie
La spectrométrie de masse à ionisation secondaire dans le cas de son utilisation en mode
dynamique repose sur le bombardement de la surface de l’échantillon par en faisceau d’ions
primaires focalisés, de haute énergie (16O ou 133Cs) avec une incidence de 20 - 45° pour
optimiser l’émission des ions secondaires. Les collisions atomiques génèrent l’ablation de la
matière minérale en surface et l’éjection de particules neutres ou chargées dont une partie est
ionisée spontanément. Ces ions sont ensuite transférés par un champ électrostatique, de la
surface de l’échantillon vers le spectromètre de masse où ils sont séparés selon leur masse et
charge (m/Q) avant leur introduction dans le détecteur (Ireland 2004). La mesure des isotopes
stables de l’oxygène est la plus problématique du fait de l’usage d’ion primaire Cs+ qui
tendent à s’accumuler à la surface du fait d’une évacuation incomplète par la couche
conductrice déposée en surface (Au). Un canon à électron rentre alors en action pour
compenser l’excès de charge positive sur la surface de l’échantillon et ainsi permettre une
bonne extraction des ions secondaire (Lyon et al. 1994; Ireland 2004; Slodzian et al. 1987).
Un des éléments propres à la technique est le biais induit par le fractionnement des masses lié
à l’ionisation préférentielle des isotopes les plus légers. De ce fait l’enrichissement relatif en
éléments légers du faisceau d’ions secondaire doit être ajusté par rapport aux rapports
isotopiques du standard pour prendre en compte ce phénomène. De plus pour garantir, la
précision et la reproductibilité des mesures et éviter les effets de fractionnement du à la
composition chimique ou la structure du minéral (effets de matrice), le minéral choisi comme
standard doit être le plus proche que possible du minéral à analyser (Ireland 1986).
Mise en œuvre et présentation des données
Les échantillons sont montés sur section polie de diamètre 1ˮ (2.54 cm) puis recouverts d’un
film d’or par évaporation sous vide.
Les résultats sont présentés sous la forme classique :
Réch et Rstd correspondent respectivement aux rapports isotopiques absolus de l’échantillon
analysé et du standard.
Diffractométrie de rayon-X
La diffraction des rayons X gouvernée par la loi de Bragg est la seule technique rendant
possible la connaissance de la position relative de tous les atomes au sein d’un cristal. Il est
alors possible de connaitre la nature et la position des atomes, la présence de symétries,
l’organisation périodique tridimensionnelle (polytypisme, ordre/désordre, cristallinité, ect.)
mais encore de déterminer la taille des domaines cohérents ou les paramètres de maille
cristalline. Elle résulte de l’interaction des rayons X avec les nuages électroniques des atomes
constitutifs du cristal considéré, la nature des atomes (Z) considérés influant sur l’intensité
diffractée (facteur de diffusion atomique).
La loi de Bragg peut alors s’écrire
Avec :
- dhkl, la distance réticulaire caractéristique des plans hkl
- θ l’angle d’incidence des rayons X sur les plans réticulaires
- n l’ordre d’interférence (nombre entier)
- λ la longueur d’onde du rayonnement
La préparation des échantillons s’effectuant selon un protocole tel que donné par (Brindley
and Brown 1980) pour les poudres désorientées lorsque l’identification de toutes les
directions cristallographiques sont nécessaire ou en lames orientées (dépôt filtre ou goutte)
principalement pour les minéraux présentant une forte anisotropie, tel que l’habitus lamellaire
des minéraux argileux.
Réferences
Allard T, Balan E, Calas G, Fourdrin C, Morichon E, Sorieul S (2012) Radiation-induced defects in clay minerals: A review. Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms 277:112-120. doi: http://dx.doi.org/10.1016/j.nimb.2011.12.044.
Brindley GW, Brown G (1980) Crystal structures of clay minerals and their X-ray identification. Mineralogical Society, London, UK.
Calas G, Allard T, Balan E, Morin G, Sorieul S (2003) Radiation-induced Defects in Nonradioactive Natural Minerals: Mineralogical and Environmental Significance. MRS Online Proceedings Library 792:null-null. doi: doi:10.1557/PROC-792-R2.6.
Ireland TR (1986) Isotope systematics of refractory inclusions from carbonaceous chondrites. The Australian National University.
Ireland TR (2004) Chapter 30 - SIMS Measurement of Stable Isotopes In: Pier AdG (ed) Handbook of Stable Isotope Analytical Techniques. Elsevier, Amsterdam, pp 652-691.
Jones JPE, Angel BR, Hall PL (1974) Electron spin resonance studies of doped synthetic kaolinite II. Clay Minerals 10:257-270.
Lyon IC, Saxton JM, Turner G, Hinton R (1994) Isotopic fractionation in secondary ionization mass spectrometry. Rapid Communications in Mass Spectrometry 8:837-843. doi: 10.1002/rcm.1290081009.
Reed SJB (1989) Ion microprobe analysis-a review of geological applications. Mineralogical Magazine 53:3-24.
Reed SJB (1990) Recent developments in geochemical microanalysis. Chemical Geology 83:1-9. doi: http://dx.doi.org/10.1016/0009-2541(90)90135-T.
Slodzian G, Chainteau MP, Dennebouy RC (1987) SIMS: self-regulated potential at insulating surfaces in presence of strong electrostatic field. CAMECA news.
Wertz J, Bolton J (1986) Electron paramagnetic resonance. Chapman and Hall.
Système d’altération et minéralisation en uranium le long du faisceau structural Kiggavik Andrew Lake (Nunavut, Canada) : modèle génétique et guides d’exploration Ce travail présente une étude multi-échelle des relations entre altération et minéralisation en uranium le long de la bordure Sud Est du bassin Meso-Proterozoïque du Thelon, au Nunavut, Canada. Les altérations associées aux minéralisations sont développées dans une série volcano-sédimentaire Archéenne appartenant à la ceinture de roche verte du Woodburn Lake Group (WLG). Elles s’expriment majoritairement par un assemblage à illite (polytypes 1Mcis & 1M trans) sudoite hématite et phosphates sulfates d'aluminium hydratés (APS). De plus des composés carbonés, cogénétiques des minéralisations, ont été identifiés comme des produits des réactions hydrothermales. La signature de l'altération, fortement guidées par les structures Est-Ouest du corridor de Kiggavik-Andrew Lake, apparaît alors très similaire à celle rencontrée dans les roches de socles des parties profondes des autres gisements d'uranium de type discordance du bassin d’Athabasca (Canada) ou de la Kombolgie (Australie). L'étude des marqueurs minéralogiques tels que les APS ont permis de mettre en évidence les transferts élémentaires au cours des processus métallogéniques et de distinguer les caractéristiques pétrographique et chimiques des processus diagénétiques et hydrothermaux. Enfin la compréhension fine de l’expression de marqueurs cristallographiques issus de l’irradiation naturelle des minéraux argileux donne de nouvelles pistes pour le traçage et la compréhension des circulations des radios-éléments à l’échelle géologique. Mots cléfs : Bassin Méso-Protérozoique du Thelon, altération, minéraux argileux, petrographie, cristallochimie et métallogenie de l’uranium. Alteration system and uranium mineralization along the Kiggavik-Andrew Lake structural trend (Nunavut, Canada): genetic model and exploration guides This work presents a multi-scale study of the relationships between alteration and uranium mineralization along the South Eastern margin of the Meso-Proterozoic Thelon Basin, Nunavut, Canada. The ore associated alterations are hosted in an Archean volcano-sedimentary sequence belonging to the Woodburn Lake Group (WLG). Their main expression is a mineral assemblage composed of dominant illite (1Mcis & 1M trans polytypes) together with sudoite hematite and aluminum phosphate sulfate minerals. Moreover carbonaceous materials cogenetic with the uranium mineralization have been identified as potential indicators of the hydrothermal conditions. At a regional scale, alteration is strongly controlled via East-West faults forming the main frame of the Kiggavik-Andrew Lake structural trend. Then from the regional to the mineral scale, alterations signatures at Kiggavik are similar to the ones described in deep basement rocks of unconformity type uranium deposits in both Athabasca (Canada) and Kombolgie (Australia) Paleoproterozoic basins. In addition mineralogical markers studies (APS minerals) lead to the distinction between hydrothermal and diagenetic processes as well as elemental transfers during fluid rock interaction. Finally, detailed studies on radiation induced defects on illite revealed new ways to tracing and better understanding the radio elements mobility in such deep seated natural systems. Keywords : Meso-Proterozoic Thelon Basin, alteration, clay minerals, petrography, crystallochemistry and uranium metallogeny.