SSV - Schroeder · PDF fileSSV Special Compensating Bypass Check Valve Range of Applications...
Transcript of SSV - Schroeder · PDF fileSSV Special Compensating Bypass Check Valve Range of Applications...
3
SS
V
SSV 18-20Special Compensating Bypass Check Valve
look at info overview
up to Δp 250 bar
PN 10-PN 400ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
Range of Applications Compared to the series SSV 10-12, the series SSV 18-20 uses an integrated non-return valve in the bypass. It automatically protects centrifugal pumps – especially those handling hot water – from damage which might occur through partial evaporation of the water content during low load operation.As soon as the pump capacity drops below a pre-determined flow rate, the bypass valve opens sufficiently to maintain the pump minimum flow rate. This rate is maintained even if the flow through the main valve to the boiler or process is completely shut off. The pressure will be reduced by integrated throttle stages within the bypass.The type SSV 20 is supplied with a larger bypass.
This is required for larger bypass flows up to 40 bar differential pressure. The choice is done in our works.The valve range SSV is utilized for fluids with a viscosity < 150 cSt without solids, e.g.:• in boiler feed water and cooling water plants• in Petrochemical and Chemical Industry and refrigeration• in potable water supply and backwater disposal • Offshore• in snow production• in steel production• for fire fighting systemsThe utilization in nuclear power plants emphasizes the reliability of these fittings (certified to KTA 1401).
SSV 18-20 (type with integrated non-return valve in the bypass)
3
bar
SSV18-20
up toΔp 250 bar
PN 10-PN 400ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
The Compensating Bypass Check Valves of the range SSV 18 can be utilized for Δp up to 220 bar, the type SSV 19 for Δp up to 250 bar and the SSV 20 for Δp up to 40 bar with temperature ranges from - 250°C up to + 400°C. The valves are manufactured in the sizes DN25 to DN500 and the range of nominal pressure is PN 10 up to PN 400 (ANSI 150-ANSI 2500). The bypass flow can be up to 50% of the main flow, recommended is up to 35%. The valve operates without additional auxiliary energy.For the protection of fluid pumps with delivery heads of above 2200 m we recommend the range SMA 63/64 (see prospect) with “ON/OFF“-regulation of the bypass.
Mode of OperationThe Compensating Bypass Check Valve is flow controlled, that means the non-return cone (3) is kept in its operating position by main flow only. The valve is designed in such a way, that the cone reaches its utmost upper position at denominated main flow.The non-return cone activates the Rotary Slide Valve (13) in the bypass by means of a lever (14). If the cone is positioned on the cone seat, the Rotary Slide Valve is completely open. It closes corresponding to the rising of the cone by delivery in main direction. The valve just allows such an amount of bypass flow, as it is necessary for supplement of the required minimum flow of the pump.As soon as the main flow exceeds the minimum pump flow, the bypass closes. On the other hand the bypass opens again, when the main flow falls short of the bypass flow.
InstallationValves SSV should preferably be connected directly to the pump discharge branch, and must be mounted vertically with flow entry from below. Limited possibilities for horizontal installation exist, but must be confirmed by the manufacturer.The bypass flow is piped back to the suction tank.
All bypass valve components are easily serviced. To facilitate serving of the bypass valve, we recommend a removable flanged pipe approx. 1 m long to be fitted to the bypass branch. We also recommend to install a pressure relieve valve and a stop valve. The stop valve must be of a type which can be locked in the “OPEN“ position.Illustration 1 shows a typical arrangement and flow scheme of our Compensating Bypass Check Valve. The hand-operated bypass feature is optional.In order to avoid vibrations in the valve and the pipes we recommend continuing the connecting line at the outlet (DN2) and Bypass branch (DN3) for approx. 2-3 m in the chosen nominal size. A pipe bend directly at the bypass branch is not admissible.
Illustration 1: Bypass Return with additional hand operated branch (optional).
SSVSpecial Compensating Bypass Check Valve
DesignThe construction is according to specification AD 2000 and particularly to EN 13445. As per Pressure Equipment Directive 97/23 EG the products are provided with the CE marking and the Declaration of Conformity. Certified according to the Module H1 (Pressure Equipment Directive 97/23 EG) all dangerous material classes of category 1 to 4 are covered. Suitable nominal size and nominal pressure are to be chosen according to the pump pressure branch. However, it must be observed, that the admissible flow velocity of 10 m/s may not be exceeded (guarantee). Compensating Bypass Check Valves in larger sizes, for higher pressures and in special designs, which are not listed here, can also be supplied (on request).If the bypass flow has been indicated too low, it may result in vibrations within the plant, a hammering Compensating Bypass Check Valve resp. a damage of the Valve and the pump (see “inquiry specifica-tion“).
ConstructionThe Valve SSV comprises a radial split body with non-return cone (3), and a separate bypass device in the bypass branch.All sliding parts are machined from proven stainless steels suitably matched to each other. Parts subjects to wear such as the check valve seat are stellite-faced. The coil springs are also made of stainless steel. In the standard version the casing is of forged steel P250GH (1.0460). In addition high- quality steels of various qualities can be supplied. In the Bypass the minimum flow is passed off automa-tically by the Bypass valve head (12). The pressure
reduction from pump pressure to the counter pressure in the bypass line takes place via the Bypass Valve Head (12), the throttle (16) and the valve (17) for type SSV 18-20.
The hand operating branch with multiport-throttle is fitted at the casing below the cone seat and serves to pass off the minimum flow via a hand-operated valve combination. We recommend the branch for protection of the internal bypass parts at ex-treme operating conditions, e.g. at high differential pressures and frequent operation in the range of by-pass flow as well as for filling and start-up of the plant.
Start-Up-Trim (SUT) substitutes the Bypass valve head during cleaning and start-up of plants and therefore spares the sophisticated regulating parts (optional, permanently open Bypass outlet). Also usable instead of the Hand operating branch.
Warm-up branch, pressure gauge branch, draining branch etc. can be provided, if required.Flange designs to DIN, ANSI, BS, ISO and all related standards are possible.
Furthermore we supply:• Compensating Bypass Check Valves with control disc and bearing plate in the bypass for high bypass flows at low pump pressure• Autonomous Minimum Flow System Type SMA 63/64 from DN65 upwards at pump pressures from PN 250-400 bar.• Multiport throttles for pressure- and flow reduction of high-pressure media from DN15 upwards and pressures from PN 10 to PN 640 bar.
3
bar
SSV18-20
Parts List SSV 18-20
Lower body Part-No. 1Upper body Part-No. 2Cone Part-No. 3Cone guide Part-No. 4Cone guide Part-No. 5Bypass branch Part-No. 10Valve head casing Part-No. 12Rotary slide Valve Part-No. 13Operating lever Part-No. 14 Throttle Part-No. 16Non-Return Valve Part-No. 17Hand-op. branch Part-No. 24Multi-port throttle Part-No. 25O-Ring Part-No. 78.1O-Ring Part-No. 78.2Socket screw Part-No. 91.1Socket screw Part-No. 91.2Coil spring Part-No. 95.1 (95.2)Coil spring Part-No. 95.3
Materials according to operating conditions and valid standards.
SSV 18-20 with non-return valve in the bypass and hand-operated branch (optional)
Spare/Wear Parts SSV 18-20
Bypass Valve Head, complete Part-No. 60, consisting of:Casing Part-No. 12Rotary slide valve Part-No. 13Operating lever Part-No. 14Dowel pin Part-No. 94.1Dowel pin Part-No. 94.2
Non-Return Valve in the Bypass Branch, complete, consisting of:Throttle Part-No. 16Non-Return Valve Part-No. 17O-Ring Part-No. 78.2Coil spring Part-No. 95.3
Single Spare PartsO-Ring Part-No. 78.1O-Ring Part-No. 78.2Coil spring Part-No. 95.1 (95.2)Coil spring Part-No. 95.3
up toΔp 250 bar
PN 10-PN 400ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
Standard body material 1.0460 (P250GH)
Dimensions and Weights of Valve Range SSV 18 - DINNominal size Valve 1)DN1mm
PNbar
CV[USG/min]
DN2mm
DN3mm
DN4mm
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
25
10-40 2.30
25
152
25
220 78180170 78 170
2020 2
63 2.301525 270 100
190190 100 190
3031 3
100 2.301525 270 100
190190 100 190
3031 3
160 2.121525 270 100
190190 100 190
3031 3.5
250 2.121525 300 115
195195 115 195
4142 4.5
32
10-40 2.30
32
1525
25
220 78180170 78 170
2020 2
63 2.301525 270 100
190190 100 190
3031 3
100 2.301525 270 100
190190 100 190
3031 3
160 2.121525 270 100
190190 100 190
3031 3.5
250 2.121525 300 115
195195 115 195
4141 4.5
40
10-40 2.30
40
152532
25
220 78180170180
78 170202022
2
63 2.30152532
270 100190190200
100 190303133
3
100 2.30152532
270 100190190200
100 190303133
3
160 2.12152532
270 100190190200
100 190303133
3.5
250 2.12152532
300 115195195205
115 195414244
4.5
50
10-40 2.86
50
152532
25
250 90190180190
90 180282830
2
63 2.86152532
280 105200200210
105 200363739
3
100 2.86152532
290 105200200210
105 200434446
3
160 2.65152532
290 105200200210
105 200434446
3.5
250 2.65152532
330 125205205215
125 205505153
4.5
SSVSpecial Compensating Bypass Check Valve
3
bar
SSV18
Dimensions and Weights of Valve Range SSV 18 - DINNominal size Valve 1)DN1mm
PNbar
CV[USG/min]
DN2mm
DN3mm
DN4mm
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
65
10-40 3.87
65
254050
40
280 105205205215
105 205414244
2
63 3.87254050
320 120220225235
120 225535558
3
100 3.87254050
340 125220225235
125 225656770
3
160 3.34254050
340 125220225235
125 225656770
3.5
250 3.34254050
370 140240240250
140 240808286
4.5
80
10-40 6.45
80
254050
40
310 120245230250
120 230484650
3
63 6.45254050
350 130245230250
130 230626064
5
100 6.45254050
370 130250240260
130 240747378
5
160 5.14254050
370 130250240260
130 240747378
6
250 5.14254050
400 150255250270
150 250103103108
8
100
10-40 9.67
100
405065
50
380 145280280300
145 280757680
3
63 9.67405065
390 145280280300
145 2809697
1016
100 9.67405065
430 155300300320
155 300116117122
6
160 7.72405065
430 155300300320
155 300116117122
7
250 7.72405065
500 180320320340
180 320184185191
9
125
10-40 15.91
125
506580
50
440 165360360380
165 360116118122
4
63 15.91506580
460 165360360380
165 360158160165
7
100 15.91506580
500 170360360380
170 360192194200
9
160 11.96506580
500 170360360380
170 360195197203
10
250 11.96506580
570 190380380400
190 380265267274
12
up toΔp 200 bar
PN 10-PN 400
SSVSpecial Compensating Bypass Check Valve
look at info overview
bar
SSV18
Dimensions and Weights of Valve Range SSV 18 - DINNominal size Valve 1)DN1mm
PNbar
CV[USG/min]
DN2mm
DN3mm
DN4mm
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
150
10-40 23.13
150
6580
100
65
500 190390395415
190 390181184191
7
63 23.136580
100520 190
400405425
190 400231234241
10
100 23.136580
100580 190
420420440
190 420264266274
13
160 16.056580
100580 190
420420440
190 420291293301
15
250 16.056580
100630 220
420420440
220 420381383393
19
200
10-40 44.84
200
80100125
80
630 240480480500
240 480364366372
10
63 44.8480
100125
650 240485485505
240 485403405411
14
100 44.8480
100125
680 240510520540
240 510446451459
17
160 20.9680
100125
720 240520535555
240 520459464473
20
250 20.9680
100125
830 265590590610
265 590704707717
27
250
10-40 55.05
250
100125150
100
730 265560560580
265 560661664672
17
63 55.05100125150
760 265550550570
265 550699702710
22
100 55.05100125150
840 280590590610
280 590788791799
23
160 34.97100125150
880 280590590610
280 590814817826
29
250 34.97100125150
1050 340700700720
340 700123912431253
59
300
10-40 81.85
300
125150200
125
860 320640640660
320 640826829837
20
63 81.85125150200
900 320640640660
320 640884887895
28
100 81.85125150200
1050 330680680100
330 680111811231133
29
160 42.29125150200
1050 330680680700
330 680111811231133
38
250 42.29125150200
1200 380740740760
380 740205120562066
75
1) Weight of hand-operating branch
Other pipe sizes, pressure ranges and special designs are deliverable on request.With reservation to changes of dimensions and weights.
up toΔp 200 bar
PN 10-PN 400
SSVSpecial Compensating Bypass Check Valve
look at info overview
3
bar
SSV18
Dimensions and Weights of Valve Range SSV 18 - ANSINominal size Valve 1)DN1inch
PNlbs
CV[USG/min]
DN2inch
DN3inch
DN4inch
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
1˝
150 2.30
1˝
0.5˝1˝
1˝
220 78180170 78 170
1919 2
300 2.300.5˝1˝ 270 100
180170 100 170
2727 3
600 2.300.5˝1˝ 270 100
190190 100 190
2829 3
900 2.120.5˝1˝ 320 125
200200 125 200
3637 3.5
1500 2.120.5˝1˝ 320 125
200200 125 200
3940 4.5
1.25˝
150 2.30
1.25˝
0.5˝1˝
1˝
220 78170170 78 170
1919 2
300 2.300.5˝1˝ 270 100
180170 100 170
2727 3
600 2.300.5˝1˝ 270 100
190190 100 190
2829 3
900 2.120.5˝1˝ 320 125
200200 125 200
3637 3.5
1500 2.120.5˝1˝ 320 125
200200 125 200
3940 4.5
1.5˝
150 2.30
1.5˝
0.5˝1˝
1.25˝
1˝
220 78180170180
78 170191920
2
300 2.300.5˝1˝
1.25˝270 100
180170180
100 170272728
3
600 2.300.5˝1˝
1.25˝270 100
190190200
100 190282931
3
900 2.120.5˝1˝
1.25˝320 125
200200210
125 200363739
3.5
1500 2.120.5˝1˝
1.25˝320 125
200200210
125 200394042
4.5
2˝
150 2.86
2˝
0.5˝1˝
1.25˝
1.5˝
250 90190180190
90 180282829
2
300 2.860.5˝1˝
1.25˝270 100
190180190
100 180333334
3
600 2.860.5˝1˝
1.25˝290 105
200200210
105 200394042
3
900 2.650.5˝1˝
1.25˝325 125
210210220
125 210525355
3.5
1500 2.650.5˝1˝
1.25˝350 135
210210220
135 210616264
4.5
up toΔp 200 bar
ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
Dimensions and Weights of Valve Range SSV 18 - ANSINominal size Valve 1)DN1inch
PNlbs
CV[USG/min]
DN2inch
DN3inch
DN4inch
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
2.5˝
150 3.87
2.5˝
1˝1.5˝2˝
1.5˝
280 105205205215
105 205434445
2
300 3.871˝
1.5˝2˝
300 115205205215
115 205515253
3
600 3.871˝
1.5˝2˝
340 125220225235
125 225626367
3
900 3.341˝
1.5˝2˝
370 140230235245
140 235757780
3.5
1500 3.341˝
1.5˝2˝
390 150240240250
150 240919397
4.5
3˝
150 6.45
3˝
1.5˝2˝
2.5˝
1.5˝
310 120245230250
120 230484650
3
300 6.451.5˝2˝
2.5˝330 125
245230250
125 230626064
5
600 6.451.5˝2˝
2.5˝370 130
250240260
130 240818084
5
900 5.141.5˝2˝
2.5˝390 140
250245265
140 245858589
6
1500 5.141.5˝2˝
2.5˝430 160
255250270
160 250117117121
8
4˝
150 9.67
4˝
1.5˝2˝
2.5˝
2˝
380 145280280300
145 280777882
3
300 9.671.5˝2˝
2.5˝390 145
280280300
145 280102103107
6
600 9.671.5˝2˝
2.5˝430 155
300300320
155 300126128133
6
900 7.721.5˝2˝
2.5˝450 165
300310320
165 310152155159
7
1500 7.721.5˝2˝
2.5˝520 190
320320340
190 320192196202
9
5˝
150 15.91
5˝
2˝2.5˝3˝
2˝
450 165360360380
165 360121123128
4
300 15.912˝
2.5˝3˝
480 165370360380
165 370160161166
7
600 15.912˝
2.5˝3˝
500 170360360380
170 360223225231
9
900 11.962˝
2.5˝3˝
530 185370375395
185 370261264271
10
1500 11.962˝
2.5˝3˝
630 230390390410
230 390344346353
12
SSVSpecial Compensating Bypass Check Valve
3
bar
SSV18
Dimensions and Weights of Valve Range SSV 18 - ANSINominal size Valve 1)DN1inch
PNlbs
CV[USG/min]
DN2inch
DN3inch
DN4inch
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
6˝
150 23.13
6˝
2.5˝3˝4˝
2.5˝
500 190390395415
190 390179181187
7
300 23.132.5˝3˝4˝
520 190390395415
190 390227230236
10
600 23.132.5˝3˝4˝
580 190420420440
190 420275277284
13
900 16.052.5˝3˝4˝
600 200420420440
200 420337339346
15
1500 16.052.5˝3˝4˝
700 260420420440
260 420413416424
19
8˝
150 44.84
8˝
3˝4˝5˝
3˝
630 240480480500
240 480362364370
10
300 44.843˝4˝5˝
650 240480480500
240 480392394400
14
600 44.843˝4˝5˝
680 240510520540
240 510445450458
17
900 20.963˝4˝5˝
750 250520535555
250 520595601609
20
1500 20.963˝4˝5˝
880 295590590610
295 590730733741
27
10˝
150 55.05
10˝
4˝5˝6˝
4˝
730 265560560580
265 560648650656
17
300 55.054˝5˝6˝
750 270560560580
270 560692694700
22
600 55.054˝5˝6˝
840 280590590610
280 590800805813
23
900 34.674˝5˝6˝
900 290590590610
290 590922927935
29
1500 34.674˝5˝6˝
1100 370700700720
370 700145514611471
59
12˝
150 81.85
12˝
5˝6˝8˝
5˝
860 320635635655
320 635818820826
20
300 81.855˝6˝8˝
880 320640640660
320 640881883889
28
600 81.855˝6˝8˝
1050 330680680700
330 680110111061115
29
900 42.295˝6˝8˝
1050 330680680700
330 680129913041313
38
1500 42.295˝6˝8˝
1250 410740740760
410 740200520122024
75
1) Weight of hand-operating branch
Other pipe sizes, pressure ranges and special designs are deliverable on request.With reservation to changes of dimensions and weights.
up toΔp 200 bar
ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
bar
SSV20
up toΔp 40 bar
PN 10-PN 400ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
Dimensions and Weights of Valve Range SSV 20 - DINNominal size Valve 1)DN1mm
PNbar
CV[USG/min]
DN2mm
DN3mm
DN4mm
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
40
10-40 2.86
40
152532
25
220 78180170180
78 170202021
2
63 2.86152532
270 100190190200
100 190303132
3
100 152535
160 152535
250 152535
50
10-40 3.87
50
254050
40
260 95205205215
95 205333538
2
63 3.87254050
300 120220225235
120 225434548
3
100 3.87254050
160 254050
250 254050
65
10-40 6.45
65
254050
40
290 110245230250
110 230514952
2
63 6.45254050
330 125245230250
125 230596164
3
100 254050
160 254050
250 254050
80
10-40 9.67
80
405065
50
330 130280280300
130 280515256
5
63 9.67405065
100 9.67405065
400 150300300320
150 300939498
6
160 9.67405065
400 150300300320
150 300939498
6
250 405065
3
bar
SSV20
up toΔp 40 bar
PN 10-PN 400ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
Dimensions and Weights of Valve Range SSV 20 - DINNominal size Valve 1)DN1mm
PNbar
CV[USG/min]
DN2mm
DN3mm
DN4mm
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
100
10-40 15.91
100
506580
50
410 160350350370
160 350108109113
5
63 15.91506580
420 160350350370
160 350129130134
6
100 15.91506580
460 170350350370
170 350136137141
6
160 506580
460 170350350370
170 350136137141
6
250 506580
125
10-40 23.13
125
6580
100
40
470 180380385405
180 380120122128
7
63 23.136580
100490 180
390395415
180 390197200207
8
100 6580
100
160 6580
100
250 6580
100
150
10-40 46.79
150
80100125
80
520 190440440460
190 440187188195
7
63 46.7980
100125
550 200445445465
200 445240242249
10
100 46.7980
100125
620 210470480500
210 470276279287
13
160 46.7980
100125
620 210480495515
210 480338343352
15
250 80
100125
200
10-40 33.33
200
100125150
100
650 240530530550
240 530390393402
10
63 33.33100125150
670 240520520540
240 520449451460
14
100 100125150
720 260560560580
260 560517520532
20
160 100125150
760 260560560580
260 560540543555
20
250 100125150
bar
SSV20
up toΔp 40 bar
PN 10-PN 400ANSI 150-2500
SSVSpecial Compensating Bypass Check Valve
look at info overview
Dimensions and Weights of Valve Range SSV 20 - DINNominal size Valve 1)DN1mm
PNbar
CV[USG/min]
DN2mm
DN3mm
DN4mm
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
250
10-40 50.56
250
125150200
125
750 270620620640
270 620671673683
20
63 50.56125150200
750 270620620640
270 620712715726
23
100 125150200
160 125150200
250 125150200
300
10-40
300
150200250
150
63 150200250
100 150200250
160 150200250
250 150200250
3
bar
SSV20
Dimensions and Weights of Valve Range SSV 20 - ANSINominal size Valve 1)DN1inch
PNlbs
CV[USG/min]
DN2inch
DN3inch
DN4inch
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
1.5˝
150 2.86
1.5˝
0.5˝1˝
1.25˝
1˝
220 78180170180
78 170191920
2
300 2.860.5˝1˝
1.25˝270 100
180170180
100 170272728
3
600 0.5˝1˝
1.25˝
900 0.5˝1˝
1.25˝
1500 0.5˝1˝
1.25˝
2˝
150 3.87
2˝
1˝1.5˝2˝
1.5˝
250 90205205215
90 250313234
2
300 3.871˝
1.5˝2˝
280 105205205215
105 205383941
3
600 3.871˝
1.5˝2˝
310 120220225235
120 225424447
3
900 1˝
1.5˝2˝
1500 1˝
1.5˝2˝
2.5˝
150 6.45
2.5˝
1˝1.5˝2˝
1.5˝
290 110245230250
110 230535154
2
300 6.451˝
1.5˝2˝
310 120245230250
120 230585659
3
600 1˝
1.5˝2˝
900 1˝
1.5˝2˝
1500 1˝
1.5˝2˝
3˝
150 9.67
3˝
1.5˝2˝
2.5˝
2˝
330 130280280300
130 280505155
3
300 9.671.5˝2˝
2.5˝350 135
280280300
135 280626367
5
600 9.671.5˝2˝
2.5˝390 140
240240260
140 240858691
5
900 9.671.5˝2˝
2.5˝410 150
300310320
150 310105106111
6
1500 1.5˝2˝
2.5˝
up toΔp 40 bar
ANSI 150-900
SSVSpecial Compensating Bypass Check Valve
look at info overview
Dimensions and Weights of Valve Range SSV 20 - ANSINominal size Valve 1)DN1inch
PNlbs
CV[USG/min]
DN2inch
DN3inch
DN4inch
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
4˝
150 15.91
4˝
2˝2.5˝3˝
2˝
410 160350350370
160 350106107111
3
300 15.912˝
2.5˝3˝
420 160360360380
160 360110111115
6
600 15.912˝
2.5˝3˝
460 170360360380
170 360134135140
6
900 2˝
2.5˝3˝
1500 2˝
2.5˝3˝
5˝
150 23.13
5˝
2.5˝3˝4˝
2.5˝
480 180380385405
180 380127129134
4
300 23.132.5˝3˝4˝
500 180380385405
180 380166168173
7
600 2.5˝3˝4˝
900 2.5˝3˝4˝
1500 2.5˝3˝4˝
6˝
150 46.79
6˝
3˝4˝5˝
3˝
520 190440440460
190 440185186193
7
300 46.793˝4˝5˝
540 190440440460
190 440232233241
10
600 46.793˝4˝5˝
620 210470480500
210 470281284292
13
900 46.793˝4˝5˝
640 220490505525
220 490343348357
15
1500 3˝4˝5˝
8˝
150 33.33
8˝
4˝5˝6˝
4˝
650 240530530550
240 530387380389
10
300 33.334˝5˝6˝
690 280 530530 260 530
408410419
14
600 4˝5˝6˝
900 4˝5˝6˝
1500 4˝5˝6˝
SSVSpecial Compensating Bypass Check Valve
3
bar
SSV20
1) Weight of hand-operating branch
Other pipe sizes, pressure ranges and special designs are deliverable on request.With reservation to changes of dimensions and weights.
up toΔp 40 bar
ANSI 150-900
SSVSpecial Compensating Bypass Check Valve
look at info overview
Dimensions and Weights of Valve Range SSV 20 - ANSINominal size Valve 1)DN1inch
PNlbs
CV[USG/min]
DN2inch
DN3inch
DN4inch
Lmm
Hmm
Smm
H1 mm
S1mm
Weightkg
G1 kg
10˝
150 50.56
10˝
5˝6˝8˝
5˝
750 270620620640
270 620677680691
17
300 50.565˝6˝8˝
770 275 620620 275 620
726729740
22
600 5˝6˝8˝
900 5˝6˝8˝
15005˝6˝8˝
12˝
150
12˝
6˝8˝
10˝
6˝
300 6˝8˝
10˝
600 6˝8˝
10˝
900 6˝8˝
10˝
1500 6˝8˝
10˝