PRODUCT DATA SHEETSika AnchorFix®-1 NFAST CURING POLYESTER ANCHORING ADHESIVE

PRODUCT DESCRIPTION

USESSika AnchorFix®-1 N may only be used by experiencedprofessionals.As a fast curing anchoring adhesive for all grades of:

Rebars / reinforcing steel▪Threaded rods▪Bolts and special fastening systems▪In the following substrates:▪Hollow and solid masonry▪Hard natural stone*▪Solid rock*▪

* These substrates may vary greatly, in particular withregard to strength, composition and porosity. There-fore, for each application the suitability of Sika Anchor-Fix®-1 N Adhesive must be tested by first applying SikaAnchorFix®-1 N Adhesive only to a sample area. Checkin particular bond strength, surface staining and discol-ouration.

CHARACTERISTICS / ADVANTAGESFast curing▪Standard guns can be used▪Can be used at low temperatures▪ETA to ETAG 029 for anchoring in masonry▪Non-sag, even overhead▪Styrene-free▪Low odour▪Low wastage▪

ENVIRONMENTAL INFORMATIONSika AnchorFix®-1 N conforms on the LEED v2009 IEQc4.1 Low Emitting Materials - Adhesives and Sealants,product category "Architectural Applications, Mul-tipurpose construction adhesive"

APPROVALS / STANDARDSInjection system for use in masonry according to ETAG029, ETA-17/0327, Declaration of Performance86553674, certified by notified product certificationbody 1020, certificate of constancy of performance1343-CPR-M 632-1, and provided with the CE marking

Product Data SheetSika AnchorFix®-1 NSeptember 2017, Version 01.01020205010010000016

1 / 5

PRODUCT INFORMATIONPackaging 300 ml standard cartridge 12 cartridges per box

pallet: 84 boxes

Colour Component A: whiteComponent B: blackComponent A+B mixed: light grey

Shelf Life 9 months from date of productionAll Sika AnchorFix®-1 N cartridges have the expiry date printed on the label.

Storage Conditions Stored properly in original, unopened, sealed and undamaged pack-aging in dry conditions at temperatures between +5 °C and +25 °C.Protect from direct sunlight.

Density ~1.74 kg/l (component A+B mixed)

TECHNICAL INFORMATIONCompressive Strength ~75 N/mm2 (7 days, +20 °C) (EN 196)

Flexural Strength ~30 N/mm2 (7 days, +20 °C) (EN 196)

Flexural E-Modulus ~4000 N/mm2 (EN 196)

Service Temperature Long term -40 °C min. / +50 °C max.Short term (1–2 hours) +80 °C

(ETAG 001, Part 5)

APPLICATION INFORMATIONMixing Ratio Component A : component B = 10 : 1 by volume

Layer Thickness 3 mm max.

Sag Flow Non-sag, even overhead

Product Temperature Sika AnchorFix®-1 N must be at a temperature of between +5 °C and +35 °Cfor application.

Ambient Air Temperature -5 °C min. / +40 °C max.

Dew Point Beware of condensation.Substrate temperature during application must be at least 3 °C above dewpoint.

Substrate Temperature -5 °C min. / +40 °C max.

Curing Time Temperature Open time - Tgel Curing time - Tcur

+35 °C – +39 °C 2 minutes 20 minutes+30 °C – +34 °C 4 minutes 25 minutes+20 °C – +29 °C 6 minutes 45 minutes+15 °C – +19 °C 15 minutes 80 minutes+10 °C – +14 °C 20 minutes 100 minutes+5 °C – +9 °C 25 minutes 2 hours0 °C – +4 °C 1 45 minutes 3 hours-5 °C – -1 °C 1 90 minutes 6 hours1 Minimum cartridge temperature: +5 °C

APPLICATION INSTRUCTIONSSUBSTRATE QUALITY

Mortar and concrete must be at the requiredstrength. No need to be 28 days old.

▪

Substrate strength (concrete, masonry, naturalstone) must be verified.

▪

Pull-out tests must be carried out if the substratestrength is unknown.

▪

The anchor hole must always be clean, dry, free fromoil and grease etc.

▪

Product Data SheetSika AnchorFix®-1 NSeptember 2017, Version 01.01020205010010000016

2 / 5

Loose particles must be removed from the holes.▪Threaded rods and rebars have to be cleaned thor-oughly from any oil, grease or any other substancesand particles such as dirt etc.

▪

MIXING

Getting the cartridge ready: 165 / 300 ml1. Unscrew the cap

2. Cut the film

3. Screw on the staticmixer

4. Place the cartridge in-to the gun and start ap-plication

Getting the cartridge ready: 420 ml1.Unscrew & remove thecap

2. screw on the staticmixer

3. Place the cartridge in-to the gun and start ap-plication

When the work is interrupted the static mixer can re-main on the cartridge after the gun pressure has beenrelieved. If the resin has hardened in the nozzle whenwork is resumed, a new nozzle must be attached.

Product Data SheetSika AnchorFix®-1 NSeptember 2017, Version 01.01020205010010000016

3 / 5

APPLICATION METHOD / TOOLS

Anchors in hollow blocksDrilling of hole with anelectric drill to the dia-meter and depth re-quired. Drill hole diamet-er must be in accordancewith anchor-and perfor-ated sleeve size.Note: with hollow materi-al do not use rotary ham-mer drills.

The drill hole must bethoroughly cleaned with around brush (brush atleast 1x). The diameter ofthe brush must be largerthan the diameter of thedrill hole.

The drill hole must becleaned after each clean-ing step with a blowpump or by compressedair, starting from the bot-tom of the hole (pump atleast 1x).Important: use oil-freecompressors.

Insert perforated sleevecompletely into the drillhole.

Pump approx. twice untilboth parts come out uni-formly. Do not use thismaterial. Release the gunpressure and clean thecartridge opening with acloth.

Inject the adhesive intothe perforated sleeve,starting from the bottom,while slowly drawing backthe static mixer. In anycase avoid entrapping air.

Close the cap from theperforated sleeve toavoid some escape of theresin during entering thesteel rod.

Insert the anchor with arotary motion into thefilled perforated sleeve.Use the adequate steelrod size.Important: the anchormust be placed within theopen time.

During the resin harden-ing time the anchor mustnot be moved or loaded.Wash tools immediatelywith Sika® Colma Cleaner.Wash hands and skinthoroughly with warmsoap water.

CLEANING OF TOOLS

Clean tools and application equipment with Sika® Thin-ner C immediately after use. Hardened / cured materi-al can only be mechanically removed.

VALUE BASEAll technical data stated in this Product Data Sheet arebased on laboratory tests. Actual measured data mayvary due to circumstances beyond our control.

LOCAL RESTRICTIONSPlease note that as a result of specific local regula-tions the performance of this product may vary fromcountry to country. Please consult the local ProductData Sheet for the exact description of the applicationfields.

ECOLOGY, HEALTH AND SAFETYFor information and advice on the safe handling, stor-age and disposal of chemical products, users shall referto the most recent Safety Data Sheet (SDS) containingphysical, ecological, toxicological and other safety-re-lated data.

Product Data SheetSika AnchorFix®-1 NSeptember 2017, Version 01.01020205010010000016

4 / 5

LEGAL NOTESThe information, and, in particular, the recommenda-tions relating to the application and end-use of Sikaproducts, are given in good faith based on Sika’s cur-rent knowledge and experience of the products whenproperly stored, handled and applied under normalconditions in accordance with Sika’s recommenda-tions. In practice, the differences in materials, sub-strates and actual site conditions are such that no war-ranty in respect of merchantability or of fitness for aparticular purpose, nor any liability arising out of anylegal relationship whatsoever, can be inferred eitherfrom this information, or from any written recom-mendations, or from any other advice offered. Theuser of the product must test the product’s suitabilityfor the intended application and purpose. Sika re-serves the right to change the properties of itsproducts. The proprietary rights of third parties mustbe observed. All orders are accepted subject to ourcurrent terms of sale and delivery. Users must alwaysrefer to the most recent issue of the local Product DataSheet for the product concerned, copies of which willbe supplied on request.

SikaAnchorFix-1N_en_GB_(09-2017)_1_1.pdf

SIKA LIMITEDWatchmeadWelwyn Garden CityHertfordshire, AL7 1BQTel: 01707 394444Web: www.sika.co.ukTwitter: @SikaLimited

SIKA IRELAND LIMITEDBallymun Industrial EstateBallymunDublin 11, IrelandTel: +353 1 862 0709Web: www.sika.ieTwitter: @SikaIreland

Product Data SheetSika AnchorFix®-1 NSeptember 2017, Version 01.01020205010010000016

5 / 5