ServerViewアラームサービスが受け取るSNMPト...
Transcript of ServerViewアラームサービスが受け取るSNMPト...
ServerViewアラームサービスが受け取るSNMPトラップ一覧です。各ベンダより提供されているデータのため、メッセージにより問い合わせ先が異なりますので注意してください。
これらのトラップは以下の場合に使用されます。
1)ポップアップメッセージの表示内容2)OSのイベントログの内容3)AlarmServiceのアラーム一覧の表示内容4)AlarmServiceのアラーム設定のアラーム一覧の表示内容5)MIBファイルのHelpのアラーム一覧のアラームタイプ
以下の一覧表と、各メッセージ表示内容の対応は下記のようになります。
TRAP-TYPE /アラームタイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
TRAPの名称:5)MIBファイルのHelpのアラーム一覧のアラームタイプに対応3)AlarmServiceのアラーム一覧の表示内容。4)AlarmServiceのアラーム設定のアラーム一覧の表示内容。
表示等の例は以下のような画面となります。1)ポップアップ
2)OSイベントログ
3)AlarmService(アラームモニタ)のアラーム一覧
ENTERPRISE OIDがenterprises.231以外は、各ベンダより提供されているため、問い合わせ先が異なります。
1)Pop Upメッセージの表示内容。2)OSのイベントログの内容。 (表示内容は英語のみです)
4)AlarmServiceのアラーム設定のアラーム一覧
5)MIBファイルのHelpのアラーム一覧のアラームタイプ
この画面を表示するための手順は以下のようになります。
1.ServerViewを起動します。
2.「アラーム」メニューのモニタを実行します。
3.AlarmServiceの[ヘルプ]をクリックします。
4.ヘルプー目次のエージェントアラーム情報をクリックします。
5.アラームMibのRFC1157.mibをクリックします。
SNI-TRAP-MIB (trap.mib)
表1:SNI-TRAP-MIB トラップ(ENTERPRISE : enterprises.231)
TRAP-TYPE/アラーム タイプ Specific 重要度詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sniNWVolSysMountedVolume SYS is mounted
0 INFORMATIONALVolume SYS is mounted on server %sサーバ%sで、システムボリュームがマウントされました。
Netware監視のTrapです。サポートしていません。
sniNWSysVolumeDismountedVolume SYS is dismounted
1 CRITICALVolume SYS is dismounted on server %sサーバ%sで、システムボリュームがディスマウントされました。
↑
sniNWVolumeMountedVolume is mounted
2 INFORMATIONALVolume %s is mounted on server %sサーバ%sで、ボリューム%sがマウントされました。
↑
sniNWVolumeDismountedVolume is dismounted
3 INFORMATIONALVolume %s is dismounted on server %sサーバ%sで、ボリューム%sがディスマウントされました。
↑
sniNWDownServerServer is going down (NetWare)
4 CRITICALServer is going down: %sサーバをダウンします:%s
↑
sniNWExitToDosServer exits to DOS
7 CRITICALServer exits to DOS : %sサーバはDOSに抜けました:%s
↑
sniNWModuleUnloadedModule is unloaded
8 INFORMATIONALModule %s is unloaded on server %sサーバ%sで、モジュール(NLM)%sがロードされていません。
↑
sniNWClearConnectionConnection is cleared
9 INFORMATIONALA connection is cleared on server %sサーバ%sの接続がクリアされました。
↑
sniNWLoginUserUser logged into server
10 INFORMATIONALA user logged into server %sサーバ%sに、ユーザがログインしました。
↑
sniNWCreateBinderyObjBindery object created
11 INFORMATIONALA bindery object is created on server %sサーバ%sで、バインダリオブジェクトが作成されました。
↑
sniNWDeleteBinderyObjBindery object deleted
12 INFORMATIONALA bindery object is deleted on server %sサーバ%sで、バインダリオブジェクトが削除されました。
↑
sniNWChangeSecuritySecurity changed (NetWare)
13 INFORMATIONALSecurity change has occurred on server %sサーバ%sで、セキュリティが変更されました。
↑
sniNWActivateScreenScreen activated
14 INFORMATIONALA screen is activated on server %sサーバ%sで、画面が活性化されました。
↑
sniNWUpdateScreenScreen updated
15 INFORMATIONALA screen is updated on server %sサーバ%sで、画面が更新されました。
↑
sniNWUpdateCursorCursor position updated
16 INFORMATIONALThe cursor position is updated on server %sサーバ%sで、カーソル位置が更新されました。
↑
sniNWKeyWasPressedKey pressed
17 INFORMATIONALA key is pressed on server %sサーバ%sで、キーが押下されました。
↑
sniNWDeactivateScreenScreen deactivated
18 INFORMATIONALA screen is deactivated on server %sサーバ%s上のスクリーンが非活性化されました。
↑
sniNWTrusteeChangeTrustee changed (NetWare)
19 INFORMATIONALTrustee is changed on server %sサーバ%sで、トラスティが変更されました。
↑
sniNWOpenScreenScreen opened
20 INFORMATIONALA Screen is opened on server %sサーバ%sで、画面が開かれました。
↑
sniNWCloseScreenScreen closed
21 INFORMATIONALA Screen is closed on server %sサーバ%sで、画面が閉じられました。
↑
sniNWModifyDirEntryDirectory entry changed
22 INFORMATIONALDirectory entry is changed on server %sサーバ%sで、ディレクトリエントリが変更されました。
↑
sniNWNoRelinquishControlNLM has not relinquished control
23 CRITICALThe NLM %s has not relinquished control on server %sサーバ%sで、NLM %sが制御を放棄していません。
↑
sniNWThreadSwitchThread switch has occurred
25 INFORMATIONALA thread switch has occurred on server %sサーバ%sで、スレッドが切り替えられました。
↑
sniNWModuleLoadedModule loaded
27 INFORMATIONALModule %s is loaded on server %sサーバ%sで、モジュール(NLM)%sがロードされました。
↑
sniNWCreateProcessProcess created
28 INFORMATIONALA Process is created on server %sサーバ%sで、プロセスが生成されました。
↑
sniNWDestroyProcessProcess destroyed
29 INFORMATIONALA Process is destroyed on server %sサーバ%sで、プロセスが破棄されました。
↑
sniNWNewPublicNew public symbol
32 INFORMATIONALA new public symbol is registered on server %sサーバ%sで、新規パブリックシンボルが登録されました。
↑
sniNWProtocolBindProtocol bound
33 INFORMATIONALA protocol is bound to a MLID on server %sサーバ%sで、MLIDにプロトコルがバインドされました。
↑
sniNWProtocolUnbindProtocol unbound
34 MAJORA protocol is unbound from a MLID on server %sサーバ%sで、MLIDからプロトコルがアンバインドされました。
↑
sniNWAllocateConnectionConnection allocated
37 INFORMATIONALA connection is allocated on server %sサーバ%sで、接続が割り当てられました。
↑
sniNWLogoutConnectionUser logged out
38 INFORMATIONALA user has logged out of server %sサーバ%sで、ユーザがログアウトしました。
↑
sniNWMLIDRegisterMLID registered
39 INFORMATIONALA MLID is registered on server %sサーバ%sで、MLIDが登録されました。
↑
sniNWMLIDDeRegisterMLID deregistered
40 INFORMATIONALA MLID is deregistered on server %sサーバ%sから、MLIDの登録が抹消されました。
↑
sniNWDataMigrationFile data migrated
41 INFORMATIONALA files data has been migrated on server %sサーバ%sで、ファイルデータが移動されました。
↑
sniNWDataDeMigrationFile data demigrated
42 INFORMATIONALA files data has been demigrated on server %sサーバ%sで、ファイルデータが復元されました。
↑
sniNWQueueActionQueue status changed
43 INFORMATIONALA queue is activated, deactivated, created or deleted onserver %sサーバ%sで、キューが活性、非活性、作成、または削除されました。
↑
sniNWAlertAlert written
44 INFORMATIONAL
A Netware Alert message is written to the console on server%s. Module %s: %sサーバ%sで、NetWareアラートメッセージがコンソールに書き込まれました。モジュール%s:%s
↑
sniNWCreateObjectDS object created
46 INFORMATIONALA Directory Service object is created on server %sサーバ%sで、Directory Serviceオブジェクトが生成されました。
↑
sniNWDeleteObjectDS object deleted
47 INFORMATIONALA Directory Service object is deleted on server %sサーバ%sで、Directory Serviceオブジェクトが削除されました。
↑
sniNWRenameObjectDS object renamed
48 INFORMATIONALA Directory Service object is renamed on server %sサーバ%sで、Directory Serviceオブジェクトが変名されました。
↑
sniNWValueChangedDS object value changed
49 INFORMATIONALA Directory Service object's value changed on server %sサーバ%sで、Directory Serviceオブジェクトの値が変更されました。
↑
sniNWCloseFileFile closed
50 INFORMATIONALA file is closed on server %sサーバ%sで、ファイルがクローズされました。
↑
sniNWChangeTimeTime changed (NetWare)
51 INFORMATIONALTime has changed or a nonuniform time adjustment hasoccurred on server %sサーバ%sで、時刻の変更、あるいは、時刻の調整が行われました。
↑
sniInvPollTrapExceededThreshold exceeded
128 INFORMATIONALThreshold exceeded : %s, on Server %sサーバ%sで、しきい値を超過しました。:%s
しきい値マネージャで設定した設定値を越えたメッセージです。
次の表は、SNI-TRAP-MIBのトラップを掲載して、概要を示したものです。ServerView コンソールからのトラップです。詳細については下表を参照してください。
sniInvPollTrapUnderflowThreshold underflow
129 INFORMATIONALThreshold underflow : %s, on Server %sサーバ%sで、しきい値の下限を超えました。:%s
↑
sniInvPollDeltaExceededDELTA-Threshold exceeded
130 INFORMATIONALDELTA-Threshold exceeded : %s, on Server %sサーバ%sで、相対しきい値を超過しました。 :%s
↑
sniInvDeltaTrapUnderflowDELTA-Threshold underflow
131 INFORMATIONALDELTA-Threshold underflow : %s, on Server %sサーバ%sで、相対しきい値の下限を超えました。:%s
↑
sniInvTrapInvalidThreshold invalid
132 INFORMATIONALThreshold Invalid: %s, on Server %sサーバ%sで、しきい値が無効です。:%s
しきい値マネージャの設定値に対するメッセージです。
sniInvTrapValidThreshold valid
133 INFORMATIONALThreshold Valid: %s, on Server %sサーバ%sで、しきい値有効です。:%s
↑
sniNTDownServerServer is going down (NT)
300 INFORMATIONALServer is going down : %sサーバをダウンします:%s
sniNTLoginUserUser logged in
301 INFORMATIONALA user logged into server %sサーバ%sに、ユーザがログインしました。
sniNTChangeSecuritySecurity changed (NT)
302 INFORMATIONALSecurity change has occurred on server %sサーバ%sで、セキュリティが変更されました。
sniNTTrusteeChangeTrustee changed (NT)
303 INFORMATIONALA trustee is changed on server %sサーバ%sで、トラスティが変更されました。
sniNTAlertNT Alert written
304 INFORMATIONAL
An NT Alert message is written to the eventlog (ControlString: %s) on server %s.サーバ%sで、NTアラートメッセージがイベントログに書き込まれました。(制御文字:%s)
sniNTChangeTimeTime changed (NT)
305 INFORMATIONALTime has changed or a nonuniform time adjustment hasoccurred on server %sサーバ%sで、時刻の変更または時刻の調整が行われました。
sniNTRegChangeNameKeyname changed
310 INFORMATIONALKeyname in registry has been changed on server %sサーバ%sで、レジストリのキー名が変更されました。
sniNTRegChangeAttrRegistry key attributes changed
311 INFORMATIONAL
Attributes for a key or its subtree in registry has beenchanged on server %sサーバ%sで、レジストリのキーまたはそのサブツリーの属性が変更されました。
sniNTRegChangeLastWriteRegistry last write time changed
312 INFORMATIONAL
Last write time for a key or its subtree in registry has beenchanged on server %sサーバ%sで、レジストリのキーまたはサブツリーへの更新時刻が変更されました。
sniNTRegChangeSecurityRegistry key security changed
313 INFORMATIONAL
Security for a key or its subtree in registry has been changedon server %sサーバ%sで、レジストリのキーまたはそのサブツリーのセキュリティが変更されました。
sniNTFileChangeNameFile name modified
320 INFORMATIONALA file name has been changed, created or deleted on server%sサーバ%sで、ファイル名が変更、作成、または削除されました。
sniNTFileChangeDirNameDirectory name modified
321 INFORMATIONALA directory name has been changed, created or deleted onserver %sサーバ%sで、ディレクトリ名が変更、作成、または削除されました。
sniNTFileChangeAttrFile attributes changed
322 INFORMATIONALFile or directory attributes have been changed on server %sサーバ%sで、ファイルまたはディレクトリの属性が変更されました。
sniNTFileChangeSizeFile size changed
323 INFORMATIONALFile size has been changed on server %sサーバ%sで、ファイルサイズが変更されました。
sniNTFileChangeLastWriteFile last write time changed
324 INFORMATIONALLast write time on a file has been changed on server %sサーバ%sで、ファイルの更新時刻が変更されました。
sniNTFileChangeSecurityFile security changed
325 INFORMATIONALSecurity on a file has been changed on server %sサーバ%sで、ファイルのセキュリティが変更されました。
sniNTEventLogErrorEventlog entry: error
330 INFORMATIONALError entry written to eventlog on server %sサーバ%sのイベントログに、エラーエントリが書き込まれました。
sniNTEventLogWarningEventlog entry: warning
331 INFORMATIONALWarning entry written to eventlog on server %sサーバ%sのイベントログに、警告エントリが書き込まれました。
sniNTEventLogInformationEventlog entry: information
332 INFORMATIONALInformational entry written to eventlog on server %sサーバ%sのイベントログに、情報エントリが書き込まれました。
sniNTEventLogSuccessEventlog entry: success audit
333 INFORMATIONALAudit failure entry written to eventlog on server %sサーバ%sのイベントログに、監査成功エントリが書き込まれました。
sniNTEventLogFailureEventlog entry: failure audit
334 INFORMATIONALFailure audit entry written to eventlog on server %sサーバ%sのイベントログに、監査失敗エントリが書き込まれました。
SNI-MYLEX-MIB (mylex.mib)
表2:SNI-MYLEX-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
mylexAutoRebuildStartedAutomatic rebuild started
200 INFORMATIONAL
Automatic rebuild of device %d on channel %d was started atdisk array adapter in slot %d. The standby device %d atchannel %d will be used (Server %s).スロット%dのディスクアレイアダプタで、チャネル%dのデバイス%dの自動リビルドが開始されました。チャネル%dの待機デバイス%dが使用されます。(サーバ%s)
mylexManualRebuildStartedManual rebuild started
201 INFORMATIONAL
Manual rebuild was started at disk array adapter in slot %d atserver %s.サーバ%sの、スロット%dのディスクアレイアダプタで、手動リビルドを開始しました。
mylexRebuildDoneRebuild done
202 INFORMATIONAL
Rebuild was successfully completed at disk array adapter inslot %d (Server %s).スロット%dのディスクアレイアダプタで、リビルドが正常に終了しました。(サーバ%s)
mylexRebuildCanceledRebuild cancelled
203 INFORMATIONAL
Rebuild was cancelled at disk array adapter in slot %d (Server%s).スロット%dのディスクアレイアダプタで、リビルドがキャンセルされました。(サーバ%s)
mylexRebuildStatusRebuild status
204 INFORMATIONAL
Rebuild status at disk array adapter in slot %d: currentdrive=%d, drive size=%d MBytes; %d MBytes remaining (Server%s).スロット%dのディスクアレイアダプタでのリビルドステイタス:現在のドライブ=%d、ドライブサイズ=%d MB;残り %d MB (サーバ%s)
mylexRebuildErrorRebuild error
205 MAJOR
Rebuild error at disk array adapter in slot %d: %d bad blocksdetected (Server %s).スロット%dのディスクアレイアダプタでのリビルドエラー:%dの不良ブロックが検出されました。(サーバ%s)
Mylex Disk Array Controllerからのトラップです。詳細についてはRAIDコントローラの説明書を参照してください。RAID Manager(GAM:Global Array Manager)
次の表は、SNI-MYLEX-MIBのトラップを掲載して、概要を示したものです。
mylexRebuildNewDeviceFailedRebuild device failed
206 MAJOR
Rebuild finished at disk array adapter in slot %d: new devicefailed (Server %s).スロット%dのディスクアレイアダプタでのリビルド終了:新規デバイスが故障しました。(サーバ%s)
mylexRebuildLogicalDriveFailedRebuild drive failed
207 MAJOR
Rebuild finished at disk array adapter in slot %d: logical drivefailed, %d bad blocks detected (Server %s).スロット%dのディスクアレイアダプタでのリビルド終了:論理ドライブが故障し、%dの不良ブロックが検出されました。(サーバ%s)。
mylexParityCheckStartedParity check started
208 INFORMATIONAL
Parity check was started at disk array adapter in slot %d(Server %s).スロット%dのディスクアレイアダプタで、パリティチェックが開始されました。(サーバ%s)
mylexParityCheckDoneParity check done
209 INFORMATIONAL
Parity check was successfully completed at disk arrayadapter in slot %d (Server %s).スロット%dのディスクアレイアダプタで、パリティチェックが正常に終了しました。(サーバ%s)
mylexParityCheckCanceledParity check cancelled
210 INFORMATIONAL
Parity check was cancelled at disk array adapter in slot %d(Server %s).スロット%dのディスクアレイアダプタで、パリティチェックがキャンセルされました。(サーバ%s)
mylexParityCheckStatusParity check status
211 INFORMATIONAL
Parity check status at disk array adapter in slot %d: currentdrive=%d, drive size=%d MB; %d MBytes remaining (Server %s).スロット%dのディスクアレイアダプタでのパリティチェックのステイタス:現在のドライブ=%d、ドライブサイズ=%d MB;残り %d MB (サーバ%s)
mylexParityCheckErrorParity check error
212 MAJOR
Parity check error at disk array adapter in slot %d: %d badblocks detected (Server %s).スロット%dのディスクアレイアダプタでのパリティチェックエラー:%dの不良ブロックが検出されました。(サーバ%s)
mylexParityCheckLogicalDriveFailedParity check: drive failed
213 MAJOR
Parity check finished at disk array adapter in slot %d; logicaldrive failed: %d bad blocks detected (Server %s).スロット%dのディスクアレイアダプタでのパリティチェック終了;論理ドライブが故障しました:%dの不良ブロックが検知されました。(サーバ%s)
mylexLogicalDriveOfflineLogical drive offline
214 CRITICAL
Logical drive %d at disk array adapter in slot %d is offline(Server %s).スロット%dのディスクアレイアダプタの論理ドライブ%dは、オフライン状態です。(サーバ%s)
mylexLogicalDriveCriticalLogical drive critical
215 MAJOR
Logical drive %d at disk array adapter in slot %d is critical(Server %s).スロット%dのディスクアレイアダプタの論理ドライブ%dは、危険な状態です。(サーバ%s)
mylexLogicalDriveOnlineLogical drive online
216 INFORMATIONAL
Logical drive %d at disk array adapter in slot %d is online(Server %s).スロット%dのディスクアレイアダプタの論理ドライブ%dは、オンライン状態です。(サーバ%s)
mylexPhysicalDeviceDiedPhysical device dead
217 CRITICAL
Physical device %d on channel %d at disk array adapter in slot%d is DEAD (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dは、停止しています。(サーバ%s)
mylexPhysicalDeviceAlivePhysical device online
218 INFORMATIONAL
Physical device %d on channel %d at disk array adapter in slot%d is now ONLINE (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dは、オンライン状態です。(サーバ%s)
mylexWriteBackErrorWrite back error
219 MAJOR
Controller cache write back error at disk array adapter in slot%d: %d bad blocks (Server %s).スロット%dのディスクアレイアダプタでの、コントローラキャッシュライトバックエラー:%dの不良ブロック。(サーバ%s)
mylexStateChangeTableFullCache change table full
220 MAJOR
Cache state-change table full at disk array adapter in slot %d(Server %s).スロット%dのディスクアレイアダプタで、キャッシュ状態変更テーブルが一杯です。(サーバ%s)
mylexAdapterDied・Disk controller died 221 CRITICAL
Connection to disk array controller in slot %d on server %slost.サーバ%sのスロット%dで、ディスクアレイコントローラとの接続が失われました。
mylexAutoRebuildStarted2Automatic rebuild started
222 INFORMATIONAL
Automatic rebuild of system drive %d was started at diskarray adapter in slot %d at server %sサーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの自動リビルドが開始されました。
mylexManualRebuildStarted2Manual rebuild started
223 INFORMATIONAL
Manual rebuild of system drive %d was started at disk arrayadapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの手動リビルドが開始されました。
mylexRebuildDone2Rebuild done
224 INFORMATIONAL
Rebuild of system drive %d was successfully completed atdisk array adapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのリビルドが正常に完了しました。
mylexRebuildCanceled2Rebuild cancelled
225 INFORMATIONAL
Rebuild of system drive %d was cancelled at disk arrayadapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのリビルドがキャンセルされました。
mylexRebuildError2Rebuild error
226 MAJOR
Rebuild error on system drive %d at disk array adapter in slot%d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dにリビルドエラーが発生しました。
mylexRebuildNewDeviceFailed2Rebuild device failed
227 MAJOR
Rebuild of system drive %d finished at disk array adapter inslot %d: new device failed at server %s.スロット%dのディスクアレイアダプタでの、システムドライブ%dのリビルド終了:サーバ%sで新規デバイスが故障しました。
mylexRebuildLogicalDriveFailed2Rebuild drive failed
228 MAJOR
Rebuild of system drive %d finished at disk array adapter inslot %d: system drive failed at server %s.スロット%dのディスクアレイアダプタでの、システムドライブ%dのリビルドが終了: サーバ%sでシステムドライブが故障しました。
mylexInitializationStartedInitialization started
229 INFORMATIONAL
Initialization of system drive %d started at disk array adapterin slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの初期化が開始されました。
mylexInitializationDoneInitialization done
230 INFORMATIONAL
Initialization of system drive %d successfully finished at diskarray adapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの初期化が正常に終了しました。
mylexInitializationCanceledInitialization canceled
231 INFORMATIONAL
Initialization of system drive %d canceled at disk array adapterin slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの初期化がキャンセルされました。
mylexInitializationFailedInitialization failed
232 MAJOR
Initialization of system drive %d failed at disk array adapter inslot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの初期化に失敗しました。
mylexSystemDriveCreatedSystem drive created
233 INFORMATIONAL
New system drive %d created at disk array adapter in slot %dat server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、新規システムドライブ%dが作成されました。
mylexSystemDriveDeletedSystem drive deleted
234 INFORMATIONAL
System drive %d deleted at disk array adapter in slot %d atserver %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dが削除されました。
mylexRaidExpansionStartedRAID expansion started
235 INFORMATIONAL
RAID capacity expansion on system drive %d started at diskarray adapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのRAID容量拡張が開始されました。
mylexRaidExpansionDoneRAID expansion done
236 INFORMATIONAL
RAID capacity expansion on system drive %d successfullyfinished at disk array adapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのRAID容量拡張が正常に終了しました。
mylexRaidExpansionFailedRAID expansion failed
237 MAJOR
RAID capacity expansion failed on system drive %d at diskarray adapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのRAID容量拡張が失敗しました。
mylexSystemDriveBadBlockBad block
238 MINOR
Bad block(s) detected on system drive %d at disk arrayadapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dの不良ブロックが検知されました。
mylexSystemDriveSizeChangedSystem drive size changed
239 INFORMATIONAL
Size of system drive %d was changed at disk array adapter inslot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのサイズが変更されました。
mylexRaidTypeChangedRAID type changed
240 INFORMATIONAL
RAID type of system drive %d was changed at disk arrayadapter in slot %d at server %s.サーバ%sで、スロット%dのディスクアレイアダプタで、システムドライブ%dのRAIDタイプが変更されました。
mylexPhysicalDeviceHotsparePhysical device hotspare
250 INFORMATIONAL
Physical device %d on channel %d at disk array adapter in slot%d is now HOTSPARE (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dは、現在ホットスペア状態です。(サーバ%s)
mylexPhysicalDeviceHardErrorPhysical device hard error
251 MINOR
Hard error occurred at physical device %d on channel %d atdisk array adapter in slot %d (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dで、ハードエラーが発生しました。(サーバ%s)
mylexPhysicalDeviceSoftErrorPhysical device soft error
252 MINOR
Soft error occurred at physical device %d on channel %d atdisk array adapter in slot %d (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dで、ソフトエラーが発生しました。(サーバ%s)。
mylexPhysicalDeviceParityErrorPhysical device parity error
253 MINOR
Parity error occurred at physical device %d on channel %d atdisk array adapter in slot %d (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dで、パリティーエラーが発生しました。(サーバ%s)
mylexPhysicalDeviceMiscErrorPhysical device miscellaneous error
254 MINOR
Miscellaneous error occurred at physical device %d on channel%d at disk array adapter in slot %d (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dで、雑多のエラーが発生しました。(サーバ%s)
mylexPhysicalDevicePrefailurePhysical device prefailure
255 MAJOR
Prefailure alert from physical device %d on channel %d at diskarray adapter in slot %d (Server %s). Device will fail in nearfuture!スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dで、障害予兆が報告されました。(サーバ%s)
mylexPhysicalDeviceUnconfiguredPhysical device unconfigured
256 MAJOR
Physical device %d on channel %d at disk array adapter in slot%d is unconfigured (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dに物理デバイス%dが構成されていません。(サーバ%s)
mylexPhysicalDeviceAddedPhysical device added
257 MAJOR
Physical device %d on channel %d at disk array adapter in slot%d was added (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dに物理デバイス%dが追加されました。(サーバ%s)
mylexPhysicalDeviceRemovedPhysical device removed
258 MAJOR
Physical device %d on channel %d at disk array adapter in slot%d was removed (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dの物理デバイス%dが取り外されました。(サーバ%s)
mylexWriteBackError2Write back error
260 MAJOR
Controller cache write back error at disk array adapter in slot%d (Server %s).スロット%dのディスクアレイアダプタの、コントローラキャッシュライトバックエラーが発生しました。(サーバ%s)
mylexGamDriverMissingMissing GAM driver
261 MINOR
GAM driver is either not installed or has failed to start;required version: %s (server %s).GAMドライバがインストールされてないか、起動に失敗しました;必要とされるバージョン:%s(サーバ%s)
mylexGamDriverIncorrectVersionIncorrect GAM driver version
262 MINOR
Incorrect version of GAM driver installed (%s); requiredversion: %s (server %s).間違ったバージョンのGAMドライバがインストールされています。(%s);必要とされるバージョン:%s(サーバ%s)
mylexSMARTFailurePredictedSMART predicted disk failure
270 CRITICAL
SMART predicts failure for disk %d on channel %d at disk arrayadapter in slot %d (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dのディスク%dについて、SMARTが故障の予兆をしました。(サーバ%s)
mylexSMARTConfigurationChangedSMART configuration changed
271 INFORMATIONAL
SMART configuration has been changed for disk %d onchannel %d at disk array adapter in slot %d (Server %s).スロット%dのディスクアレイアダプタの、チャネル%dのディスク%dについてSMARTの構成が変更されました。(サーバ%s)
mylexBBUFoundBBU found
275 INFORMATIONAL
A Battery Backup Unit was found on SCSI controller in slot%d (Server %s).スロット%dのSCSIコントローラにバッテリバックアップユニットが見つかりました。(サーバ%s)
mylexBBUPowerLowBBU power low
276 CRITICAL
The Battery Backup Unit power on SCSI controller in slot %dis low (Server %s). If this messages happens without powerfailure, replace the BBU.スロット%dのSCSIコントローラで、バッテリバックアップユニットの電源が低下しています。(サーバ%s)
mylexBBUPowerOKBBU power OK
277 INFORMATIONAL
The Battery Backup Unit power on SCSI controller in slot %dis OK (Server %s).スロット%dのSCSIコントローラで、バッテリバックアップユニットの電源は正常です。(サーバ%s)
SNI-SERVER-CONTROL-MIB (sc.mib)
表3:SNI-SERVER-CONTROL-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
testTrapTest trap
600 INFORMATIONALTest trap from server %s (no error).サーバ%sからのテストトラップ。(エラーではありません)
エラーではありません。
fanErrorFan failed
601 CRITICALFan %d failed in cabinet %d of server %s.サーバ%sのキャビネット%dで、ファン%dが故障しました。
FAN異常です。担当保守員に連絡してください。
tempOkTemperature normal
602 INFORMATIONAL
Temperature at sensor %d in cabinet %d of server %s is withinnormal range.サーバ%sのキャビネット%dで、温度センサ%dが正常範囲内に下がりました。
筐体内温度が正常範囲内です。エラーではありません。
tempWarnTemperature warning
603 MAJOR
Temperature at sensor %d in cabinet %d of server %s hasreached the warning level.サーバ%sのキャビネット%dで、温度センサ%dが警告レベルに達しました。
tempCriticalTemperature critical
604 CRITICAL
Temperature at sensor %d in cabinet %d of server %s hasreached the critical level.サーバ%sのキャビネット%dで、温度センサ%dが危険レベルに達しました。
trapOnBatteryAC failed, on battery
606 CRITICAL
AC failure. Cabinet %d is running on battery power since %dseconds. In %d minutes server %s will shutdown.ACに異常があります。キャビネット%dは、%d秒間バッテリ電源で作動しています。サーバ%sは%d分後にシャットダウンします。
UPSのバッテリで運転しています。停電、またはUPSの電源ケーブル等が抜けていないか確認してください。
trapOnMainsAC OK
607 INFORMATIONALMains returned after power failure in cabinet %d at server %s.ACは正常です。サーバ%sのキャビネット%dが停電後、主電源が回復しました。
UPSのバッテリ運転が解除されました。
selftestWarningController selftest warning
608 MINOR
The Server Management controller in cabinet %d has detectedan minor problem during selftest of server %s.キャビネット%dのサーバ管理コントローラが、サーバ%sのセルフテスト中、軽度の問題を検知しました。
特に問題ではありません。メッセージが多数検出される場合、サーバ管理コントローラの障害が考えられます。担当保守員に連絡してください。
selftestErrorController selftest error
609 CRITICAL
The Server Management controller in cabinet %d of server %sfailed.サーバ%sのキャビネット%dで、サーバ管理コントローラが故障しました。
担当保守員に連絡してください。
svCommunicationFailureCommunication lost
610 MINOR
Communication with the Server Management controller incabinet %d of server %s lost.サーバ%sのキャビネット%dで、サーバ管理コントローラとの通信が失われました。
イベントID:10636で復旧している場合、問題ありません。復旧されない場合、担当保守員に連絡してください。
scbUnconfiguredUPSDetectedUPS not configured
611 INFORMATIONALUPS detected by server %s, but no UPS is configured.サーバ%sでUPSを検知しましたが、UPSは構成されていません。
scbUPSNotdetectedUPS not detected
612 MAJORA UPS is configured but no UPS detected by server %s.UPSが構成されていますが、サーバ%sでは検知されませんでした。
scbUnconfiguredBBUDetectedBBU not configured
613 INFORMATIONALBBU detected by server %s, but no BBU is configured.サーバ%sでBBUを検知しましたが、BBUは構成されていません。
scbBBUNotdetectedBBU not detected
614 INFORMATIONALA BBU is configured but no BBU is detected by server %s.BBUが構成されていますが、サーバ%sでは検知されませんでした。
notEnoughCabinetsSE's missing
615 MAJOR
The actual number of storage extensions at server %s is lowerthan the configured.サーバ%sの拡張記憶装置の実際数が、構成されている数を下回っています。
tooManyCabinetsToo many SE's
616 MINOR
The actual number of storage extensions at server %s ishigher than the configured.サーバ%sの拡張記憶装置の実際数が、構成されている数を超えています。
cabinetSwitchedOffCabinet switched off
617 INFORMATIONALCabinet %d was switched off because of %s (server %s).サーバ%sのキャビネット%dが、電源切断<%s>しました。
サーバ%sが電源切断しました。
cabinetSwitchedOnCabinet switched on
618 INFORMATIONALCabinet %d was switched on because of %s (server %s).サーバ%sのキャビネット%dが、電源投入<%s>しました。
サーバ%sが電源投入しました。
internalErrorInternal error
620 INFORMATIONAL
Internal error #%d in server management controller software.(module %s at server %s).サーバ%sのサーバ管理コントローラで内部エラー#%dが発生しました。(モジュール %s)
ソフトエラーです。モジュール名を特定してサポートセンターに問い合わせをお願いします。
serverShutdownServer shutdown
621 INFORMATIONALThe reason %s causes a shutdown at server %s.%sの理由により、サーバ%sをシャットダウンします。
シャットダウン指示によりサーバをシャットダウンします。
fanCriticalErrorFan will fail
622 INFORMATIONALFan %d will fail in near future in cabinet %d of server %s.サーバ%sのキャビネット%dで、ファン%dが近い将来故障の可能性があります。
fan異常の予兆です。すぐに故障することはありません。担当保守員に相談してください。
cabinetNotConfiguredCabinet not configured
623 INFORMATIONAL
Cabinet %d at server %s is not configured. Depending on thesystem type, run Server Configuration Utility (SCU) or StorageExtension Manager (SEMAN) and configure the cabinet!サーバ%sのキャビネット%dが構成されていません。ハード添付の保守ツールを使用して再設定を実行してください。
キャビネット内の構成が正しく行われていません。再設定を行ってください。
powerSupplyRemovedPower supply removed
624 INFORMATIONALPower supply %d in cabinet %d at server %s was removed.サーバ%sのキャビネット%dから、電源装置%dが取り外されました。
オペレータにより、電源ユニットが取り外されました。
powerSupplyAddedPower supply added
625 INFORMATIONALPower supply %d in cabinet %d at server %s was added.サーバ%sのキャビネット%dに、電源装置%dが取り付けられました。
オペレータにより、電源ユニットが取り付けられました。
powerSupplyFailedPower supply failed
626 MAJORPower supply %d in cabinet %d at server %s failed.サーバ%sのキャビネット%dで、電源装置%dが故障しました。
電源ユニットが故障しました。担当保守員に連絡してください。
powerSupplyOkPower supply OK
627 INFORMATIONALPower supply %d in cabinet %d at server %s is working again.サーバ%sのキャビネット%dで、電源装置%dが動作を再開しました。
電源ユニットを取り付けた後に通知されるメッセージです。
powerSupplyStatusCriticalPower supply critical
628 CRITICAL
Insufficiant operating power supplies available in cabinet %d atserver %s.サーバ%sのキャビネット%dで、使用できる電源装置の稼動が不十分です。
電源ユニットの搭載を行ってください。
fanOkFan OK
629 INFORMATIONALFan %d in cabinet %d of server %s is working again.サーバ%sのキャビネット%dで、ファン%dが正常に戻りました。
FANが正常に戻ったメッセージです。FAN交換を行った場合のメッセージです。
筐体内温度異常です。室温の確認を行ってください。問題ない場合、FANの故障が発生していないか確認してください。その他ハード異常が考えられます。担当保守員に連絡してください。
設定ミスの可能性があります。再度確認してください。設定に誤りがない場合、UPSの異常が考えられます。担当保守員に連絡してください。
外部記憶装置の構成に誤りがあります。再確認をお願いします。
次の表は、SNI-SERVER-CONTROL-MIBのトラップを掲載して、概要を示したものです。ServerViewエージェント又はRSBからのトラップです。詳細については以下の表を参照してください。
tempSensorBrokenTemperature sensor broken
630 MAJOR
Temperature sensor %d in cabinet %d of server %s is broken ornot connected.サーバ%sのキャビネット%dで、温度センサ%dが故障しているか接続されていません。
温度センサーが故障している可能性があります。担当保守員に連絡してください。
serverManagementDisabledServer management disabled
631 INFORMATIONAL
Server management BIOS on server %s is disabled. Enable itto have full server management functionality!サーバ%sのサーバ管理BIOSが無効です。全サーバ管理機能を利用するためには、サーバ管理BIOSを有効にして下さい。
サーバ管理を有効にするためにハードに添付されている保守ツールを使用して設定を行ってください。
trapAcFailAC failed
632 CRITICALAC failure in cabinet %d of server %s.サーバ%sのキャビネット%dに、AC異常があります。
UPSのスケジュール運転を行っている場合に格納されるメッセージです。この場合問題はありません。UPSのスケジュール運転を行っていない場合、電源異常の可能性がありますので担当保守員に連絡してください。
trapDuplicateCabinetIdDuplicate cabinet ID
633 MAJORTwo or more cabinets have the same ID %d on server %s.サーバ%sの2つあるいはそれ以上のキャビネットが同じID%dを持っています。
システム構成に間違いがあります。再設定をお願いします。
trapEventLogError in event log
634 MAJOR
An error was recorded on server %s. See server managementevent / error log (Recovery) for detailed information.サーバ%sのエラーが記録されました。詳細情報は、イベント/エラーログ(復旧)を参照してください。
post中にエラーが発生しました。ServerViewの「アクション」「エラーバッファ」に格納されている情報を参照してください。
tempSensorOkTemperature sensor OK
635 INFORMATIONALTemperature sensor %d in cabinet %d of server %s is workingagain.サーバ%sのキャビネット%dで、温度センサ%dが動作を再開しました。
温度センサーが復旧したメッセージです。
svCommunicationEstablishedCommunication established
636 INFORMATIONAL
Communication with the Server Management controller incabinet %d of server %s established again.サーバ%sのキャビネット%dで、サーバ管理コントローラとの通信が再び確立されました。
サーバ管理コントローラとの通信が復旧したメッセージです。
correctableMemErrorAddrCorrectable memory error
637 INFORMATIONAL
Correctable memory error at address %d in cabinet %d ofserver %s.サーバ%sのキャビネット%dで、アドレス%dに訂正可能なメモリエラーが発生しました。
SBE(メモリ1ビットエラー)が発生しました。ECCメモリのため特に影響はありません。
uncorrectableMemErrorAddrUncorrectable memory error
638 CRITICAL
Uncorrectable memory error at address %d in cabinet %d ofserver %s.サーバ%sのキャビネット%dで、アドレス%dに訂正不可能なメモリエラーが発生しました。
MBE(メモリマルチビットエラー)が発生しました。担当保守員に連絡してください。
correctableMemErrorBankCorrectable memory error #1
639 INFORMATIONAL
Correctable memory error at bank %d in cabinet %d of server%s.サーバ%sのキャビネット%dで、バンク%dに訂正可能なメモリエラーが発生しました。
SBE(メモリ1ビットエラー)が発生しました。ECCメモリのため特に影響はありません。
uncorrectableMemErrorBankUncorrectable memory error #1
640 CRITICAL
Uncorrectable memory error at bank %d in cabinet %d ofserver %s.サーバ%sのキャビネット%dで、バンク%dに訂正不可能なメモリエラーが発生しました。
MBE(メモリマルチビットエラー)が発生しました。担当保守員に連絡してください。
correctableMemErrorModuleCorrectable memory error #2
641 INFORMATIONAL
Correctable memory error at module %d in cabinet %d ofserver %s.サーバ%sのキャビネット%dで、モジュール%dに訂正可能なメモリエラーが発生しました。
SBE(メモリ1ビットエラー)が発生しました。ECCメモリのため特に影響はありません。
uncorrectableMemErrorModuleUncorrectable memory error #2
642 CRITICAL
Uncorrectable memory error at module %d in cabinet %d ofserver %s.サーバ%sのキャビネット%dで、モジュール%dに訂正不可能なメモリエラーが発生しました。
MBE(メモリマルチビットエラー)が発生しました。担当保守員に連絡してください。
correctableMemErrorCorrectable memory error #3
643 INFORMATIONALCorrectable memory error in cabinet %d of server %s.サーバ%sのキャビネット%dで、訂正可能なメモリエラーが発生しました。
SBE(メモリ1ビットエラー)が発生しました。ECCメモリのため特に影響はありません。
uncorrectableMemErrorUncorrectable memory error #3
644 CRITICALUncorrectable memory error in cabinet %d of server %s.サーバ%sのキャビネット%dで、訂正不可能なメモリエラーが発生しました。
MBE(メモリマルチビットエラー)が発生しました。担当保守員に連絡してください。
powerOffTimeReachedPower off time reached
645 INFORMATIONAL
The power-off time is reached in cabinet %d on server %s!System shutdown in %d minutes.サーバ%sのキャビネット%dが、電源切断時刻になりました。システムは%d分後にシッャトダウンされます。
ServerViewで指定したスケジュール電源OFF、または、ServerViewコンソールよりシャットダウン指示が行われました。
frontDoorStatusChangedFront door status changed
646 INFORMATIONALThe front door status of cabinet %d on server %s has changed.サーバ%sのキャビネット%dで、フロント扉の状態が変化しました。
オペレータにより、扉の開閉が行われました。
housingOpenStatusChangedHousing open status changed
647 INFORMATIONALThe housing open status of cabinet %d on server %s haschanged.サーバ%sのキャビネット%dで、筐体カバーの状態が変化しました。
オペレータにより、筐体カバーの開閉が行われました。
sniScRedundantFanFailedRedundant fan failed
648 MAJOR
The redundant fan %d failed in cabinet %d of server %s.System can become critical if another fan in this group fails.サーバ%sのキャビネット%dで、冗長ファン%dが故障しました。このグループの別のファンが故障すると、システムが危険な状態になる可能性があります。
冗長FANの故障です。担当保守員に連絡してください。
sniScRedundantPowerSupplyFailedRedundant power supply failed
649 MAJOR
Redundant power supply %d in cabinet %d at server %s failed.System can become critical if another power supply fails.サーバ%sのキャビネット%dで、冗長電源%dが故障しました。このグループの別の電源装置が故障すると、システムが危険な状態になる可能性があります。
冗長電源の故障です。担当保守員に連絡してください。
sniScVoltageOkVoltage OK
650 INFORMATIONAL
Power supply voltage %d (%s) in cabinet %d at server %s iswithin normal range again.サーバ%sのキャビネット%dで、電源装置の電圧%d(%s)が再び正常範囲内に戻りました。
サーバの電圧が復旧しました。問題ありません。
sniScVoltageTooLowVoltage too low
651 CRITICAL
Power supply voltage %d (%s) in cabinet %d at server %s is toolow.サーバ%sのキャビネット%dで、電源装置の電圧%d(%s)が低すぎます。
電源ユニットやAC電源に不具合がある場合があります。担当保守員に相談してください。
sniScVoltageTooHighVoltage too high
652 CRITICAL
Power supply voltage %d (%s) in cabinet %d at server %s is toohigh.サーバ%sのキャビネット%dで、電源装置の電圧%d(%s)が高すぎます。
電源ユニットやAC電源に不具合がある場合があります。担当保守員に相談してください。
sniScFanAddedFan added
653 INFORMATIONALThe fan %d was added into cabinet %d of server %s.サーバ%sのキャビネット%dに、ファン%dが取り付けられました。
オペレータにより、FANが取り付けられました。
sniScFanRemovedFan removed
654 INFORMATIONALThe fan %d was removed from cabinet %d of server %s.サーバ%sのキャビネット%dから、ファン%dが取り外されました。
オペレータにより、FANが取り外されました。
sniScShutdownCancelledShutdown cancelled
655 INFORMATIONALShutdown at server %s cancelled by the user.サーバ%sのシッャトダウンがユーザによりキャンセルされました。
オペレーションです。
sniScCpuSpeedChangedCPU speed changed
656 INFORMATIONAL
CPU speed at server %s changed to %d percent of itsmaximum speed. The CPU speed can be changed by theserver management because of temperature problems.サーバ%sのCPUスピードが、 大出力の%dパーセントに変更されました。CPUスピードは温度の問題のために、サーバマネジメントによって変更された可能性があります。
CPU温度が高温となったため、CPU速度を落として稼働しています。CPU温度の確認を行ってください。fanの故障により、CPU温度が上昇っしている可能性があります。
sieScPowerOnPower on
657 INFORMATIONALThe reason %s causes a power on at server %s.サーバ%sが要因<%s>でPowerONしました。
電源が投入されたメッセージです。
sieScNoBootCpuNo boot cpu
658 INFORMATIONAL
System boot of the server %s failed, because no valid bootcpu available.ブートCPUが存在しないため、サーバ%sのシステムブートに失敗しました。
システムの確認を行ってください。CPU異常が発生している可能性があります。
sieScPostErrorPost error
659 INFORMATIONALThe reason %s causes a power on at server %s.サーバ%sが要因<%s>でPowerONしました。
頻発する場合、担当保守員に相談してください。
sieScSetupEnteredSetup entered
660 INFORMATIONALThe bios setup is entered at server %s.サーバ%sでBIOSセットアップになった。
オペレータにより、セットアップ処理が行われました。
sieScBootErrorBoot error
661 INFORMATIONALNo bootable operation system found at server %s.サーバ%sにブート可能なOSが見つかりません。
システムの確認を行ってください。
sieScBootWatchdogExpiredBoot watchdog expired
662 INFORMATIONALBoot watchdog of server %s expired.サーバ%sで、ブート時間監視が終了し、異常を検出しました。
設定されているリトライカウンタ分処理が行われました。リトライカウンタの再設定を行ってください。
sieScSoftwareWatchdogExpiredSoftware watchdog expired
663 INFORMATIONALSoftware watchdog of server %s expired.サーバ%sで、ソフトウェア時間監視が終了し、異常を検出しました。
設定されているリトライカウンタ分処理が行われました。リトライカウンタの再設定を行ってください。
sieScUserAuthenticationFailureUser authentication failure
664 MAJOR
User authentication failure detected at server %s, interface%d, performing protocol %s.サーバ%sでユーザー認証失敗を検出しました。プロトコル:%s、管理チャネル番号:%d。
認証処理の確認を行ってください。
sieScDiagnosticBootDiagnostic boot
665 INFORMATIONALServer %s is performing a diagnostic boot.サーバ%sは診断ブートを実行しています。
オペレータにより、診断処理が実行されました。
sieScBootRetryCountZeroBoot retry counter zero
666 MAJOR
Boot retry counter is zero on server %s. On next critical errorshutdown the server will no longer try to reboot. System willrun diagnostic system or switch off.サーバ%sのブートリトライカウンタがゼロになりました。次に重度のエラーでサーバがシャットダウンされた場合、サーバはブートしません。システムは診断システムを起動するかPowerOffします。
設定されているリトライカウンタ分処理が行われました。リトライカウンタの再設定を行ってください。
sieScMessageLogFullMessage log full
667 MINOR
The System Event Log on server %s in cabinet %d is full. Nomore messages can be logged. Please clear unneeded logentries as soon as possible!サーバ%sのキャビネット%dで、System Event Logが一杯になりました。これ以上のメッセージは、ロギングできません。できるだけ早く、不要なSystem Event Logをクリアしてください!
ハード添付の保守ツールを使用して不要なSystem Event Logのクリアを行ってください。
memErrorModulePrefailureMemory module prefailure
668 MAJOR
Memory module failure is predicted for module %d in cabinet%d of server %s.サーバ%sのキャビネット%dで、モジュール%dのメモリモジュールエラーが予測されます。
メモリエラーの予兆です。担当保守員に相談してください。
memErrorModuleFailingMemory module failing
669 MAJOR
Memory module %d in cabinet %d of server %s is failing. Toomany errors have occured.This module will automatically be disabled on next reboot.サーバ%sのキャビネット%dで、メモリモジュール%dに多くのエラーが発生しました。このモジュールは、次のリブートで自動的に無効にされます。
メモリエラーの予兆警告です。担当保守員に連絡してください。
memErrorModuleReplacedMemory module replaced
670 MAJOR
Memory module module %d in cabinet %d of server %s hadfailedand was replaced by a hot-spare module.サーバ%sのキャビネット%dで、メモリモジュール%dにエラーが発生し、ホットスペアメモリに切り替わりました。
メモリエラーです。担当保守員に連絡してください。
sniScPowerSupplyRedundancyLostPower supply redundancy lost
671 MINOR
Power supply redundancy in cabinet %d at server %s lost.System will become critical if a power supply fails.サーバ%sのキャビネット%dで、電源の冗長性が失われました。もし電源が故障した場合、システムに異常をきたします。
電源ユニットのエラーです。担当保守員に相談してください。
sieScMessageLogWarningMessage log warning
672 MINOR
The System Event Log for cabinet %d at server %s hasexceeded %d%% of its capacity.サーバ%sのキャビネット%dで、System Event Logが、その容量の%d%を超えました。
System Event Log の予兆です。ハード添付の保守ツールを使用して不要なSystem Event Logをクリアしてください。
sieScCpuPrefailureCPU prefailure
673 MAJORCPU failure is predicted for CPU %d in cabinet %d of server %s.サーバ%sのキャビネット%dで、CPU%dの故障が予測されます。
CPU異常の予兆警告です。担当保守員に連絡してください。
sieScPowerFailPower failed
674 CRITICALDC power failure in cabinet %d of server %s.サーバ%sのキャビネット%dで、DC電源異常です。
電源ユニットのエラーです。担当保守員に相談してください。
sieScBiosSelftestErrorCritical BIOS selftest error
675 CRITICAL
A critical error happend while BIOS selftest in cabinet %d ofserver %s.See server management message log (recovery log)for detailed information.サーバ%sのキャビネット%dで、BIOSセルフテスト中にCriticalErrorを検出しました。
BIOSセルフテスト中のエラー検出です。詳細はSELを参照し担当保守員に連絡して下さい。
SNI-SERVERVIEW-MIB (serverview.mib)
表4:SNI-SERVERVIEW-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sniSvGenericTrapForwardServerView alarm received
700 INFORMATIONAL
The server %s sent the trap <%s> to ServerView application atstation %sサーバ%sが、トラップ<%s>をステーション%sのServerViewアプリケーションに送信しました。
アラームサービスによって転送されたTrapです。
sniSvPagerOffPager turn off
701 INFORMATIONALPager number %d should be turned off.番号%dのページャが電源切断されています。
sniSvServerStateChangedServer changed state
702 INFORMATIONALThe server %s has changed its state to %sサーバ%sの状態が、%sに変更されました。
sniSvPassThroughTrapForwardServerView alarm passed through
703 INFORMATIONAL %sアラームサービスによって転送されたTrapです。
sieSvAlarmServiceCommandAlarm Service Command
704 INFORMATIONALCommand %d from server %s.サーバ%sからのコマンド%d
fscSvServerAddedServer added
705 INFORMATIONALServer %s was added.サーバ%sが追加された。
fscSvServerRemovedServer removed
706 INFORMATIONALServer %s was removed.サーバ%sが削除された。
fscSvServerChangedServer changed
707 INFORMATIONALServer %s was changed.サーバ%sが変更された。
fscSvServerStatusChangedServer status changed
708 INFORMATIONALServer status %s was changed.サーバのステータス%sが変更された。
fscSvGroupAddedGroup added
709 INFORMATIONALGroup (%s, %d) was added.Group (%s, %d)が追加された。
fscSvGroupRemovedGroup removed
710 INFORMATIONALGroup (%s, %d) was removed.Group (%s, %d)が削除された。
ServerView管理コンソールのトラップです。詳細については以下の表を参照してください。次の表は、SNI-SERVERVIEW-MIBのトラップを掲載して、概要を示したものです。
fscSvGroupChangedGroup changed
711 INFORMATIONALGroup (%s, %d) was changed.Group (%s, %d)が変更された。
fscSvExploreServerExplore server
712 INFORMATIONALExplore server %s.サーバ%sを調査。
fscAsTestMailAlarm Service Test Mail
747 INFORMATIONALThe Alarm Service on server %s sends a test mail.サーバ%sのアラームサービスがテストmailを送出しました。
fscAsTestPagerAlarm Service Test Pager
748 INFORMATIONALThe Alarm Service on server %s tests a pager.サーバ%sのアラームサービスがページャをテストしました。
fscAsStopTrapListenServiceAlarm Service Stop Trap Listen Service
749 INFORMATIONALThe ServerView Alarm Service Trap Listen Service on server%s stops.サーバ%sのアラームサービスのトラップサービスが停止しました。
SNI-HD-MIB (hd.mib )
表5:SNI-HD-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sniSMARTFailurePredictedSMART predicted disk failure
750 CRITICAL
SMART predicts failure on disk %d (%s), adapter %d (%s), onServer %s.サーバ%sで、SMARTがアダプタ%d(%s)のディスク%d(%s)の故障を予測しました。
DISKエラーの予兆警告です。担当保守員に連絡してください。
sniSMARTMonitoringDisabledSMART configuration changed
751 INFORMATIONAL
SMART configuration has been changed on hard disk %d (%s),adapter %d (%s), on Server %s.サーバ%sで、アダプタ%d(%s)のハードディスク%d(%s)でSMARTの構成が変更されました。
SMARTモードが変更されたメッセージです。
SNI-NT-CLUSTER-MIB (ntcluster.mib)
次の表は、SNI-NT-CLUSTER-MIBのトラップを掲載して、概要を示したものです。
表6:SNI-NT-CLUSTER-MIB トラップ(ENTERPRISE : enterprises.231)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sniWpChangeUnknownunknown notification type
801 INFORMATIONAL The cluster has sent the unknown notification 0x%X.未サポートアプリケーション(ClusterView)からのトラップです。通常表示されません。
sniWpChangeClusterNotFoundActiveabnormal cluster status
810 CRITICALSNMP cannot access cluster software. Trap sent from server%s.
↑
sniWpChangeClusterActiveAgainnormal cluster status
811 INFORMATIONALSNMP gained access to the cluster software. Trap sent fromserver %s.
↑
sniWpChangeClusterNoLongerActiveabnormal cluster status
812 CRITICALSNMP lost access to the cluster software. Trap sent fromserver %s.
↑
sniWpChangeNodeDeletednode deleted
830 INFORMATIONAL The node %s has been deleted. ↑
sniWpChangeNodeAddednode added
831 INFORMATIONAL The node %s has been added. ↑
sniWpChangeNodeStatenode state change
832 MAJOR The node %s has changed its state. ↑
sniWpChangeResourceTypeDeletedresource type deleted
840 INFORMATIONAL Resource type %s has been deleted. ↑
sniWpChangeResourceTypeAddedresource type created
841 INFORMATIONAL Resource type %s has been created. ↑
sniWpChangeGroupDeletedgroup deleted
850 INFORMATIONAL Group %s has been deleted. ↑
sniWpChangeGroupAddedgroup created
851 INFORMATIONAL Group %s has been created. ↑
sniWpChangeGroupStategroup state change
852 MAJOR Group %s has changed its state. ↑
sniWpChangeGroupPropertygroup properties change
853 INFORMATIONAL The properties of group %s have changed. ↑
sniWpChangeResourceDeletedresource deleted
860 INFORMATIONAL Resource %s has been deleted. ↑
sniWpChangeResourceAddedresource added
861 INFORMATIONAL Resource %s has been added. ↑
sniWpChangeResourceStateresource state change
862 MAJOR Resource %s has changed its state. ↑
sniWpChangeResourcePropertyresource properties change
863 INFORMATIONAL The properties of resource %s have changed. ↑
sniWpChangeRegistryAttributescluster attributes change
895 INFORMATIONAL The attributes of registry key %s have been changed. ↑
sniWpChangeRegistryKeyregistry namespace change
896 INFORMATIONAL Registry key %s has been created or deleted. ↑
sniWpChangeRegistryValueregistry value change
897 INFORMATIONAL A value of registry key %s has been changed. ↑
sniWpChangeNetworkDeletednetwork deleted
910 INFORMATIONAL Network %s has been deleted. ↑
sniWpChangeNetworkAddednetwork created
911 INFORMATIONAL Network %s has been created. ↑
sniWpChangeNetworkStatenetwork state change
912 MAJOR Network %s has changed its state. ↑
sniWpChangeNetworkPropertynetwork properties change
913 INFORMATIONAL The properties of Network %s have changed. ↑
sniWpChangeNetInterfaceDeletednetwork interface deleted
920 INFORMATIONAL Network interface %s has been deleted. ↑
sniWpChangeNetInterfaceAddednetwork interface created
921 INFORMATIONAL Network interface %s has been created. ↑
sniWpChangeNetInterfaceStatenetwork interface state change
922 MAJOR Network interface %s has changed its state. ↑
sniWpChangeNetInterfacePropertynetwork interface properties change
923 INFORMATIONAL The properties of network interface %s have changed. ↑
sniWpNodeUpCluster node online
924 INFORMATIONAL Cluster node %s is online. ↑
sniWpNodeDownCluster node offline
925 INFORMATIONAL Cluster node %s is offline. ↑
sniWpNodePausedCluster node paused
926 INFORMATIONAL Cluster node %s has been paused. ↑
次の表は、SNI-HD-MIBのトラップを掲載して、概要を示したものです。FSC HD SMARTMonitoringからのトラップです。
sniWpNodeJoiningCluster node joining
927 INFORMATIONAL Cluster node %s is joining. ↑
sniWpGroupOnlineCluster group online
928 INFORMATIONAL Cluster group %s is online. ↑
sniWpGroupPartialOnlineCluster group partially online
929 INFORMATIONAL Cluster group %s is partially online. ↑
sniWpGroupPendingCluster group pending
930 INFORMATIONAL Cluster group %s is pending. ↑
sniWpGroupOfflineCluster group offline
931 INFORMATIONAL Cluster group %s is offline. ↑
sniWpGroupFailedCluster group failed
932 MAJOR Cluster group %s has failed. ↑
sniWpResourceOnlineCluster resource online
933 INFORMATIONAL Cluster resource %s is online. ↑
sniWpResourceOfflineCluster resource offline
934 INFORMATIONAL Cluster resource %s is offline. ↑
sniWpResourceFailedCluster resource failed
935 MAJOR Cluster resource %s has failed. ↑
sniWpNetworkUpNetwork reactivated
936 INFORMATIONAL Cluster network %s reactivated. ↑
sniWpNetworkDownCluster network down
937 INFORMATIONAL Cluster network %s down. ↑
sniWpNetworkUnavailableCluster network unavailable
938 MAJOR Cluster network %s unavailable. ↑
sniWpNetInterfaceUpCluster network interface reactivated
939 INFORMATIONAL Cluster network interface %s reactivated. ↑
sniWpNetInterfaceFailedCluster network interface failed
940 MAJOR Cluster network interface %s has failed. ↑
sniWpNetInterfaceUnreachableCluster network interface unreachable
941 MAJOR Cluster network interface %s unreachable. ↑
sniWpNetInterfaceUnavailableCluster network interface unavailable
942 MAJOR Cluster network interface %s unavailable. ↑
PCI-HOTPLUG-MIB (pcihotplug.mib)
表7:PCI-HOTPLUG-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
siePciHotPlugTrapHotRemovalStart of HotPlug action
1000 INFORMATIONALA Hot Removal action is started on physical slot %d (server%s).
未サポートアプリケーション(ClusterView)からのトラップです。通常表示されません。
siePciHotPlugTrapHotReplaceStart of HotPlug action
1001 INFORMATIONALA Hot Replace action is started on physical slot %d (Server%s).
↑
siePciHotPlugTrapEndHotPlugActionEnd of HotPlug action
1002 INFORMATIONALThe HotPlug action on physical slot %d is terminated %s(Server %s). The card state is : %s
↑
sieDeviceHotPlugTrapHotRemovalDevice HotPlug action
1020 INFORMATIONALA SCSI device <%s> on SCSI adapter <%s> (PCI Bus Number%d, Device Number %d) has been removed (server %s).
↑
sieDeviceHotPlugTrapHotReplaceDevice HotPlug action
1021 INFORMATIONALA SCSI device <%s> on SCSI adapter <%s> (PCI Bus Number%d, Device Number %d) has been replaced (server %s).
↑
sieDeviceHotPlugTrapHotAddDevice HotPlug action
1022 INFORMATIONALA SCSI device <%s> on SCSI adapter <%s> (PCI Bus Number%d, Device Number %d) has been added (server %s).
↑
SERVERVIEW-STATUS-MIB (status.mib)
表8:SERVERVIEW-STATUS-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sieStTrapStatusChangedStatus changed
1100 INFORMATIONALSystem status has changed at server %s.サーバ%sで、システムの状態が変化しました。
前後のTrapを確認してください。
SIEMENS-MULTIPATH-MIB (mp.mib)
表9:SIEMENS-MULTIPATH-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sieMPErrorMP: Last port failed
1200 CRITICALMultiPath group %d on server %s is down.サーバ%sで、MultiPathグループ%dがダウンしています。
sieMPRetryMP: Port failed
1201 MAJOR
Port %d of MultiPath group %d on server %s is down. Error onID %d, Lun %d.サーバ%sで、MultiPathグループ%dのポート%dがダウンしています。ID%d、Lun %dにエラーがあります。
sieMPActivePortChangedMP: Port activated
1202 INFORMATIONAL
Active port for MultiPath group %d changed on server %s. Port%d is now active port.サーバ%sで、MultiPathグループ%dのアクティブポートが変更されました。ポート%dが、現在のアクティブポートです。
sieMPReconfiguredMP: Port added/removed
1203 INFORMATIONAL
MultiPath group %d reconfigured on server %s. Port %d wasaffected.サーバ%sで、MultiPathグループ%dが再構成されました。ポート%dに異常がありました。
sieMPStatusChangedMP: Behavior changed
1204 INFORMATIONALMultiPath behavior for group %d was changed on server %s.サーバ%sで、グループ%dのMultiPath動作が変更されました。
sieMPAutoRecoveredMP: Port alive again
1205 INFORMATIONAL
MultiPath group %d on server %s: Port %d recovered fromerror.サーバ%sのMultiPathグループ%d:ポート%dは、エラーから復旧しました。
sieMPErrorClearedMP: Status cleared
1206 INFORMATIONAL
MultiPath group %d on server %s: Error for MultiPath port %dwas cleared.サーバ%sのMultiPathグループ%d:MultiPathポート%dのエラーは解消されました。
次の表は、SIEMENS-MULTIPATH-MIBのトラップを掲載して、概要を示したものです。FSC MultiPath SNMP agent'sからのトラップです。
PCI HOTPLUGからのトラップです。
次の表は、SERVERVIEW-STATUS-MIBのトラップを掲載して、概要を示したものです。ServerViewステータスエージェントからのトラップです。詳細については以下の表を参照してください。
次の表は、PCI-HOTPLUG-MIBのトラップを掲載して、概要を示したものです。
SERVERVIEW-DUPLEXDATAMANAGER-MIB (ddm.mib)
表10:SERVERVIEW-DUPLEXDATAMANAGER-MIB トラップ(ENTERPRISE : enterprises.231.2.10.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
fscDdmNewConfigDDM: New DuplexWrite configuration
1400 INFORMATIONAL
Configuration for DuplexWrite group %d/%d/%d/%d was createdor updated on server %s.サーバ%sで、DuplexWriteグループ %d %d %d %dの構成が作成または更新されました。
fscDdmPieceRemovedDDM: DuplexWrite piece removed
1401 INFORMATIONALDuplexWrite piece %d/%d/%d/%d was removed from group onserver %sサーバ%sで、DuplexWrite %d %d %d %dが削除されました。
fscDdmConfigRemovedDDM: DuplexWrite configuration removed
1402 INFORMATIONALDuplexWrite group %d/%d/%d/%d was removed on server %s.サーバ%sで、DuplexWriteグループ %d %d %d %dが削除されました。
fscDdmStatusSetDDM: DuplexWrite status changed
1403 MINOR
Status of DuplexWrite piece %d/%d/%d/%d on server %s haschanged (user request).サーバ%sで、DuplexWrite %d %d %d %dのステータスが変更されました。(user request)
fscDdmUpdateStatusDDM: DuplexWrite status updated
1404 MINOR
Status of DuplexWrite piece %d/%d/%d/%d on server %s haschanged (driver request).サーバ%sで、DuplexWrite %d %d %d %dのステータスが変更されました。(driver request)
fscDdmPieceRecoveredDDM: DuplexWrite piece recovered
1405 INFORMATIONALDuplexWrite piece %d/%d/%d/%d successfully recovered onserver %s.サーバ%sで、DuplexWrite %d %d %d %dが復旧しました。
fscDdmRecoverAbortedDDM: Recover aborted
1406 MINOR
DuplexWrite piece %d/%d/%d/%d aborted Recover process onserver %s.サーバ%sで、DuplexWrite %d %d %d %dが復旧処理を中止しました。
fscDdmReservationConflictDDM: reservation conflict
1407 INFORMATIONAL
Reservation conflict occured on DuplexWrite group%d/%d/%d/%d on server %s - group is not accessible.サーバ%sで、DuplexWrite %d %d %d %dにReservation conflictが発生しました。グループは利用できません。
fscDdmConfigChangedDDM: DuplexWrite configuration changed
1408 INFORMATIONALDuplexWrite has found a new configuration on server %s.サーバ%sで、DuplexWriteが新しい構成を検出しました。
fscDdmConfigInvalidatedDDM: DuplexWrite configuration invalidated
1409 INFORMATIONAL
Configuration information was invalidated for DuplexWritegroup %d/%d/%d/%d on server %s.サーバ%sで、DuplexWriteグループ %d %d %d %dの構成情報が無効です。
fscDdmActiveLunChangedDDM: Active DuplexWrite piece changed
1410 INFORMATIONALDuplexWrite piece %d/%d/%d/%d is used for read commandson server %s.サーバ%sで、DuplexWrite %d %d %d %dがリードコマンドを使用した。
fscDdmPieceFailedDDM: DuplexWrite piece failed
1411 CRITICALDuplexWrite piece %d/%d/%d/%d failed on server %s.サーバ%sで、DuplexWrite %d %d %d %dが異常です。
fscDdmRootFlagChangedDDM: RootDisk flag changed
1412 INFORMATIONAL
RootDisk flag changed on DuplexWrite group %d/%d/%d/%d onserver %s.サーバ%sで、DuplexWrite %d %d %d %dのルートディスクフラグが変更されました。
fscDdmForceActiveDDM: DuplexWrite piece forced active
1413 INFORMATIONAL
DuplexWrite piece %d/%d/%d/%d marked forced active onserver %s (Snapshot).サーバ%sで、DuplexWrite %d %d %d %dの強制活性が行われます。(Snapshot)
fscDdmNameChangedDDM: DuplexWrite name changed
1414 INFORMATIONAL
Name of DuplexWrite group %d/%d/%d/%d has changed onserver %s.サーバ%sで、DuplexWriteグループ %d %d %d %dの名前が変更されました。
fscDdmPathFailedDDM: MultiPath path failed
1415 CRITICALMultiPath path %d/%d/%d/%d failed on server %s.サーバ%sで、MultiPathのパス %d %d %d %dが異常です。
fscDdmRetryDDM: MultiPath path retried
1416 MAJOR
MultiPath path %d/%d/%d/%d failed on server %s - retrysuccessful on other port.サーバ%sで、MultiPathのパス %d %d %d %dが異常がありました。他のポートで再試行が成功しました。
fscDdmActivePortChangedDDM: Active MultiPath path changed
1417 INFORMATIONALMultiPath path %d/%d/%d/%d is active on server %s.サーバ%sで、MultiPathのパス %d %d %d %dが活性化しました。
fscDdmReconfiguredDDM: MultiPath reconfigured
1418 INFORMATIONALMultiPath configuration changed on server %s.サーバ%sで、MultiPathの構成が変更されました。
fscDdmStatusChangedDDM: MultiPath status changed
1419 INFORMATIONAL
Status of MultiPath path %d/%d/%d/%d has changed on server%s.サーバ%sで、MultiPathのパス %d %d %d %dのステータスが変更されました。
fscDdmAutoRecoveredDDM: MultiPath path AutoRecovered
1420 INFORMATIONALMultiPath path %d/%d/%d/%d automatically recovered onserver %s.サーバ%sで、MultiPathのパス %d %d %d %dが自動復旧しました。
fscDdmErrorClearedDDM: MultiPath path error cleared
1421 INFORMATIONALError cleared on MultiPath path %d/%d/%d/%d on server %s.サーバ%sで、MultiPathのパス %d %d %d %dのエラーが解消されました。
fscDdmPnPRemoveDDM: PnP Removal
1422 INFORMATIONAL Plug and Play Removal occured on server %s.
fscDdmPnPNewDDM: PnP Add
1423 INFORMATIONAL Plug and Play Add occured on server %s.
fscDdmClusterDDM: Cluster configuration changed
1424 INFORMATIONALCluster configuration changed on server %s.サーバ%sで、クラスター構成が変更されました。
BLADE-MIB (S31.mib)
表11: BLADE-MIB トラップ(ENTERPRISE : enterprises.7244.1.1.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
s31TestTrapTest trap
1600 INFORMATIONAL Test trap from blade chassis %s (no error).
s31MgmtBladeAddedManagement blade added
1601 INFORMATIONAL Management blade %d at blade chassis %s was added.
s31MgmtBladeRemovedManagement blade removed
1602 INFORMATIONAL Management blade %d at blade chassis %s was removed.
DuplexDataManageからのトラップです。詳細についてはS60説明書を参照してください。
次の表は、BLADE-MIBのトラップを掲載して、概要を示したものです。BladeServerBX300/BX600からのトラップです。詳細についてはBX300/BX600説明書を参照してください。
次の表は、SERVERVIEW-DUPLEXDATAMANAGER-MIBのトラップを掲載して、概要を示したものです。
s31MgmtBladeOkStatus of management blade is OK
1603 INFORMATIONAL Management blade %d at blade chassis %s status is ok.
s31MgmtBladeErrorStatus of management blade is error
1604 MAJOR Management blade %d at blade chassis %s status is error.
s31MgmtBladeCriticalErrorStatus of management blade is critical
1605 CRITICAL Management blade %d at blade chassis %s status is critical.
s31ServerBladeAddedServer blade added
1606 INFORMATIONAL Server blade %d at blade chassis %s was added.
s31ServerBladeRemovedServer blade removed
1607 INFORMATIONAL Server blade %d at blade chassis %s was removed.
s31ServerBladeOkStatus of server blade is OK
1608 INFORMATIONAL Server blade %d at blade chassis %s status is OK.
s31ServerBladeErrorStatus of server blade is error
1609 MAJOR Server blade %d at blade chassis %s status is error.
s31ServerBladeCriticalErrorStatus of server blade is critical
1610 CRITICAL Server blade %d at blade chassis %s status is critical.
s31SwitchBladeAddedSwitch blade added
1611 INFORMATIONAL Switch blade %d at blade chassis %s was added.
s31SwitchBladeRemovedSwitch blade removed
1612 INFORMATIONAL Switch blade %d at blade chassis %s was removed.
s31SwitchBladeOkStatus of switch blade is OK
1613 INFORMATIONAL Switch blade %d at blade chassis %s status is OK.
s31SwitchBladeErrorStatus of switch blade is error
1614 MAJOR Switch blade %d at blade chassis %s status is error.
s31SwitchBladeCriticalErrorStatus of switch blade is critical
1615 CRITICAL Switch blade %d at blade chassis %s status is critical.
s31SysFanAddedSystem fan added
1616 INFORMATIONAL System fan %d at blade chassis %s was added.
s31SysFanRemovedSystem fan removed
1617 INFORMATIONAL System fan %d at blade chassis %s was removed.
s31SysFanOkStatus of system fan is OK
1618 INFORMATIONAL System fan %d at blade chassis %s status is OK.
s31SysFanErrorStatus of system fan is error
1619 MAJOR System fan %d at blade chassis %s status is error.
s31SysFanCriticalErrorStatus of system fan is critical
1620 CRITICAL System fan %d at blade chassis %s status is critical.
s31SysTempOkTemperature normal
1621 INFORMATIONALTemperature at system temperature sensor %d of bladechassis %s is within normal range.
s31SysTempErrorTemperature abnormal
1622 MAJORTemperature at system temperature sensor %d of bladechassis %s is out of normal range.
s31SysTempCriticalErrorTemperature critical
1623 CRITICALTemperature at system temperature sensor %d of bladechassis %s has reached the critical level.
s31SysTempSensorOkSystem temperature sensor OK
1624 INFORMATIONALSystem temperature sensor %d of blade chassis %s is workingagain.
s31SysTempSensorBrokenSystem temperature sensor broken
1625 MAJORSystem temperature sensor %d of blade chassis %s is brokenor not connected.
s31SysPowerSupplyAddedPower supply added
1626 INFORMATIONAL Power supply unit %d at blade chassis %s was added.
s31SysPowerSupplyRemovedPower supply removed
1627 INFORMATIONAL Power supply unit %d at blade chassis %s was removed.
s31SysPowerSupplyOkPower supply OK
1628 INFORMATIONAL Power supply unit %d at blade chassis %s is working again.
s31SysPowerSupplyErrorPower supply failed
1629 MAJOR Power supply unit %d at blade chassis %s failed.
s31SysPowerSupplyCriticalErrorPower supply critical
1630 CRITICALInsufficiant operating power supplies unit available in powersupply unit %d at blade chassis %s.
s31ServerPowerOnPower on
1631 INFORMATIONAL Server blade %d at blade chassis %s is powered on.
s31ServerPostErrorPost error
1632 INFORMATIONAL Server blade %d at blade chassis %s is posted error.
s31ServerBootErrorBoot error
1633 INFORMATIONALNo bootable operation system found at server blade %d ofblade chassis %s.
s31ServerShutdownServer shutdown
1634 INFORMATIONAL Server blade %d at blade chassis %s is shutdowned.
s31ServerSoftwareWatchdogExpiredSoftware watchdog expired
1635 INFORMATIONALSoftware watchdog at server blade %d of blade chassis %sexpired.
s31ServerBootWatchdogExpiredBoot watchdog expired
1636 INFORMATIONAL Boot watchdog at server blade %d of blade chassis %s expired.
s31UserAuthenticationFailureUser authentication failure
1637 MAJORUser authentication failure detected at blade chassis %s,performing protocol %s.
s31TrapEventLogError in event log
1638 MAJORAn error was recorded on blade chassis %s. See servermanagement event error log (Recovery) for detailed information.
s31ServerBladeNewAddServer blade was added on a empty slot
1639 INFORMATIONAL Server blade %d at blade chassis %s is added on a empty slot.
s31ServerBladeHotReplaceServer blade was added on a marked for hotreplacement slot
1640 INFORMATIONALServer blade %d at blade chassis %s is added on a marked forhot replacement slot.
s31ServerPowerOffPower off
1641 INFORMATIONAL Server blade %d at blade chassis %s is powered off.
s31SysTempSensorAddedSystem temperature sensor added
1642 INFORMATIONAL System temperature sensor %d of blade chassis %s is added.
s31SysTempSensorRemovedSystem temperature sensor removed
1643 INFORMATIONALSystem temperature sensor %d of blade chassis %s isremoved.
s31LivetimeErrorSystem live time has exceeded the limited count
1644 INFORMATIONAL Server %s live time has exceeded the limited count.
s31PowerOverBudgetServer blade power on failed
1645 INFORMATIONALServer blade %d at blade chassis %s power on failed becauseof over power budget.
s31NicDetectionFailNic detection failed
1646 INFORMATIONALManagement blade %d at blade chassis %s NIC detectionfailed.
s31SysPowerSupplyOvpFailPower supply OVP fail
1647 INFORMATIONAL Power supply unit %d OVP fail.
s31SysPowerSupplyOcpFailPower supply OCP fail
1648 INFORMATIONAL Power supply unit %d OCP fail.
s31FiberChannelAddedFiber channel pass through card added
1649 INFORMATIONALFiber channel pass through card %d at blade chassis %s wasadded.
s31FiberChannelRemovedFiber channel pass through card removed
1650 INFORMATIONALFiber channel pass through card %d at blade chassis %s wasremoved.
s31SysPowerSupplyOverallStatusOkSystem power supply overall status
1651 INFORMATIONAL System power supply overall status = OK
s31SysPowerSupplyOverallStatusDegradedSystem power supply overall status
1652 INFORMATIONAL System power supply overall status = degraded
s31SysPowerSupplyOverallStatusCriticalSystem power supply overall status
1653 INFORMATIONAL System power supply overall status = critical
s31SysFanOverallStatusOkSystem fan overall status
1654 INFORMATIONAL System fan overall status = OK
s31SysFanOverallStatusDegradedSystem fan overall status
1655 INFORMATIONAL System fan overall status = degraded
s31SysFanOverallStatusCriticalSystem fan overall status
1656 INFORMATIONAL system fan overall status = critical
s31SysTemperatureOverallStatusOkSystem temperature overall status
1657 INFORMATIONAL System temperature overall status = OK
s31SysTemperatureOverallStatusDegradedSystem temperature overall status
1658 INFORMATIONAL System temperature overall status = degraded
s31SysTemperatureOverallStatusCriticalSystem temperature overall status
1659 INFORMATIONAL System temperature overall status = critical
AdaptecArrayController-MIB (aac.mib)
表12: AdaptecArrayController-MIB トラップ(ENTERPRISE : enterprises.795.10.1.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
aacDriveLetterChangeA Drive Letter Changed
1 INFORMATIONAL A Drive Letter Changed on controller %s for container %d.
aacFailoverChangeA change in failover assignments occurred
2 INFORMATIONAL A change in failover assignments occurred on controller %s.
aacContainerStateChangeA container changed its state
3 MINOR A container changed its state on controller %s. Container : %d.
aacFileSystemChangeA file system change has occurred
4 INFORMATIONALA file system change has occurred on container %d oncontroller %s.
aacGeneralContainerFailureAn unknown error occurred on container
6 MAJOR An unknown error occurred on container %d on adapter %s.
aacMirrorNotMirroringContainer no longer mirroring
7 MAJORThe container %d on controller %s is no longer in the mirroringstate.
aacMirrorFailureNoSpaceNot enough failover space for mirror
8 CRITICALA failover operation for controller %s container %d failed becausethere was not enough space available on the failover device.
aacMirrorFailureNoUnmirrorContainer could not be unmirrored
9 CRITICAL The container %d on controller %s could not be unmirrored.
aacMirrorFailoverStartedMirror failover started
10 INFORMATIONALA mirror failover operation started on controller %s forcontainer %d.
aacMirrorFailoverFailedMirror failover failed
11 CRITICAL A failover operation on controller %s failed for container %d.
aacMirrorNoFailoverAssignedNo failover for mirror
12 MINORThere is no failover device assigned to container %d oncontroller %s.
aacMirrorDriveFailureMirror drive failure
13 CRITICALA drive that was part of the mirror set (container) %d failed.This occurred on controller %d.
aacRaidRebuildStartRebuild started
14 INFORMATIONAL A rebuild operation started on controller %s for container %d.
aacRaidRebuildRestartRebuild restarted
15 INFORMATIONAL A rebuild operation restarted on controller %s for container %d.
aacRaidDriveFailureRAID Drive Failure
16 CRITICALA drive that was part of the RAID set (container) %d failed.This occurred on controller %s.
aacRaidNoFailoverNo failover for RAID
17 MINORThere is no failover device assigned to container %d oncontroller %s.
aacRaidNoSpaceNot enough failover space for RAID
18 CRITICALA failover operation for controller %s container %d failed becausethere was not enough space available on the failover device.
aacSnapshotContainerAlmostFullSnapshot almost full
19 MAJOR The snapshot container %d on controller %s is almost full.
aacSnapshotContainerFullSnapshot full
20 CRITICAL The snapshot container %d on controller %s is full.
aacRaidRebuildCompleteRebuild complete
21 INFORMATIONALThe rebuild operation on controller %s for container %d hascompleted.
aacDeviceFailureDevice failure
22 CRITICAL A device has failed. Controller %s. Bus %d. ID %d LUN %d.
aacControllerResumeController resume
23 INFORMATIONAL The controller %s resumed normal I/O operations.
aacInterfaceUpInterface up
24 INFORMATIONAL The AAC management interface is up.
aacBatteryReconditionRequiredBattery reconditioning required
25 MAJOR The controller %s requires battery reconditioning.
aacEnclosureGeneralErrorEnclosure general error
26 MAJORAn enclosure connected to controller %s has reported anerror.
aacEnclosureFanErrorEnclosure fan error
27 MAJORAn enclosure connected to controller %s has reported a fanfailure.
aacEnclosurePowerSupplyErrorEnclosure power supply error
28 MAJORAn enclosure connected to controller %s has reported a powersupply failure.
aacEnclosureTempAbnormalEnclosure temperature abnormal
29 MAJORAn enclosure connected to controller %s has reported anabnormal temperature reading.
aacEnclosureTempOverEnclosure temperature too high
30 CRITICALAn enclosure connected to controller %s has reported atemperature reading above the user threshold.
aacBatteryDeadBattery dead
31 CRITICAL The battery connected to controller %s is dead.
aacBatteryImprovingBattery improving
32 INFORMATIONAL The battery connected to controller %s is improving.
aacBatteryDegradingBattery degrading
33 MAJOR The battery connected to controller %s has lost charge.
aacBatteryGoodBattery good
34 INFORMATIONAL The controller %s reports that its battery is good.
aacControllerPausedController paused
35 MINOR The controller %s has been paused.
aacContainerCreatedContainer created
36 INFORMATIONAL Container %d has been created on controller %s.
aacContainerDeletedContainer deleted
37 INFORMATIONAL Container %d has been deleted on controller %s.
aacDeviceFailurePredictionThresholdExceededDevice failure prediction threshold exceeded
38 MAJORA device reported that its Failure Prediction Threshold hadbeen exceeded. Controller %s. Bus %d. ID %d LUN %d.
aacDeviceFailurePredictionTestDevice failure prediction test
39 INFORMATIONALA Failure Prediction Threshold test occurred. Controller %s.Bus %d. ID %d. LUN %d.
aacDeviceWarningDevice warning
40 MAJORA Device issued a warning. Controller %s. Bus %d. ID %d LUN%d.
aacDeviceTemperatureWarningDevice temperature warning
41 MAJORA Device issued a abnormal temperature warning. Controller%s. Bus %d. ID %d LUN %d.
aacDeviceDegradedWarningDevice degraded warning
42 MINORA device reported that its status is degraded. Controller %s.Bus %d. ID %d LUN %d.
aacDeviceFailurePredictionConfigurationChangedDevice failure prediction configuration changed
43 INFORMATIONALThe failure prediction configuration changed for a device.Controller %s. Bus %d. ID %d LUN %d.
次の表は、AdaptecArrayController-MIBのトラップを掲載して、概要を示したものです。BladeServerBX600用のHostRAID Adaptec Array Controllerのトラップです。詳細についてはBX600説明書を参照してください。
aacGlobalHotSpareReplacedSuccessFailover Replaced
44 INFORMATIONAL A failover device has been replaced on controller %s.
aacDedicatedHotSpareReplacedSuccessFailover Replaced
45 INFORMATIONALA failover device has been replaced on container %d,controller %s.
aacGlobalHotSpareReplacedTooSmallFailover Replaced
46 WARNINGThe failover device that was replaced on controller %s is toosmall.
aacDedicatedHotSpareReplacedTooSmallFailover Replaced
47 WARNINGThe failover device that was replaced on container %d,controller %s is too small.
aacDedicatedHotSpareReplacedArrayNotExistFailover Replaced
48 WARNINGThe failover device has been replaced on container %d,controller %s. However, container %d does not exist.
aacBatteryTemperatureWarningBattery Temperature Warning
49 WARNINGThe battery connected to controller %s has reported an overtemperature warning.
aacBatteryTemperatureCriticalBattery Temperature Critical
50 CRITICALThe battery connected to controller %s, has reported that it iscritically over temperature.
aacBatteryTemperatureCriticalRecoverBattery Temperature Critical Recover
51 INFORMATIONALThe battery connected to controller %s, has reported that ithas recovered from a critical over temperature.
aacBatteryTemperatureNormalBattery Temperature Warning Recover
52 INFORMATIONALThe battery connected to controller %s, has returned tonormal.
aacContainerMetadataUnknownErrorContainer Metadata Unknown Error
53 CRITICALContainer %d has experienced an unknown metadata error oncontroller %s.
aacContainerMetadataReadErrorA metadata read error has occurred
54 CRITICALA metadata read error has occurred. Controller %s. Bus %d. ID%d LUN %d.
aacContainerMetadataCRCFailureErrorContainer Metadata CRC Failure Error
55 CRITICALA metadata CRC faiure has occurred. Controller %s. Bus %d.ID %d LUN %d.
aacContainerMiscompareErrorContainer Miscompare Error
56 CRITICALContainer %d has experienced miscompare error(s) oncontroller %s.
aacSCSIBusResetThere has been a SCSI bus reset
57 INFORMATIONAL There has been a SCSI bus reset. Controller %s. Bus %d.
aacSenseDataSense data event
58 INFORMATIONALA sense data event has occurred. Controller %s. Bus %d. ID %dLUN %d. Key %s. ASC %s ASCQ %s.
aacMediumErrorThere has been a device medium error
59 MAJORThere has been a device medium error. Controller %s. Bus %d.ID %d LUN %d. Begin LBA %s End LBA %s.
aacBadBlockRecoveryStartingThe bad block recovery has started.
60 INFORMATIONALThe bad block recovery has started. Controller %s. Bus %d. ID%d LUN %d.
aacBadBlockRecoveryCompletingThe bad block recovery has completed
61 INFORMATIONALThe bad block recovery has completed. Controller %s. Bus %d.ID %d LUN %d.
aacInvalidIOAn invalid I/O event has occurred
62 MAJORAn invalid I/O event has occurred. Controller %s. Bus %d. ID%d LUN %d. Expected Bytes %d, Actual Bytes %d.
aacDisablingChannelDisabling channel event
63 MINORA disabling channel event has occurred. Controller %s. Bus %d.Error Code %d
aacCannotReadyDeviceSystem can not ready the device
64 MAJORThe system can not ready the device. Controller %s. Bus %d.ID %d LUN %d.
aacChannelTimeoutChannel Timeout
65 MAJOR A channel timeout has occurred. Controller %s. Bus %d.
aacSenseDataUnknownSense data event
66 MAJORA sense data event has occurred. Controller %s. Bus %d. ID %dLUN %d. Key %s. ASC %s ASCQ %s.
aacCommandTimeoutA command timeout has occurred
67 MAJORA command timeout has occurred. Controller %s. Bus %d. ID%d LUN %d. OpCode %s.
aacContainerMediumErrorWarningA medium error was encountered while rebuilding acontainer
68 WARNINGA medium error was encountered while rebuilding a containeron Controller %s. Container %d. Block Number %s.
DESKTRAP-MIB (desktrap.mib)
表13:DESKTRAP-MIB トラップ(ENTERPRISE : enterprises.231.2.10.3)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
sniTrapErrorNo Text found in DeskMon.ini
1 MINOR No Text found in DeskMon.ini on %s未サポートアプリケーション(DeskView)からのトラップです。通常表示されません。
sniSmartOKSMART hard disk reports OK
1001 INFORMATIONAL SMART hard disk reports OK on %s ↑
sniSmartWarningSMART hard disk reports Warning
1002 MINOR SMART hard disk reports Warning on %s ↑
sniSmartErrorSMART hard disk reports Error.
1003 CRITICAL SMART hard disk reports Error on %s ↑
sniCoverClosedThe cover is closed
2001 INFORMATIONAL The cover is closed on %s ↑
sniCoverOpenedThe cover has been opened.
2003 CRITICAL The cover has been opened on %s ↑
sniCoverSensorincorporatedThe sensor for securing the cover is incorporated.
3001 INFORMATIONAL The sensor for securing the cover is incorporated on %s ↑
sniCoverSensorMissingThe sensor for securing the cover is missing ordefective
3003 CRITICALThe sensor for securing the cover is missing or defective on%s
↑
sniCoverRecognitionThe cover type cannot be recognized.
4001 INFORMATIONAL The cover type cannot be recognized on %s ↑
sniCoverRecognitionMissingThe sensor for recognizing the cover type ismissing or defective.
4003 CRITICALThe sensor for recognizing the cover type is missing ordefective on %s
↑
sniNoShortCurcuitNo short circuit in the mouse, keyboard or USBinterface.
5001 INFORMATIONALNo short circuit in the mouse, keyboard or USB interface on%s
↑
sniShortCurcuitShort circuit in the mouse, keyboard or USB
5003 CRITICAL Short circuit in the mouse, keyboard or USB interface on %s ↑
sniTemperatureOKThe temperature sensor is functioning
7001 INFORMATIONAL The temperature sensor is functioning on %s ↑
sniTemperatureWarningThe temperature is high
7002 MINOR The temperature is high on %s ↑
sniTemperatureCriticalThe temperature sensor is defective or thetemperature is too high
7003 CRITICALThe temperature sensor is defective or the temperature is toohigh on %s
↑
sniFanRunningThe fan is running
8001 INFORMATIONAL The fan is running on %s ↑
sniFanNotRunningThe fan is not running
8003 CRITICAL The fan is not running on %s ↑
sniFanWornOKThe rotational speed of the fan is OK.
9001 INFORMATIONAL The rotational speed of the fan is OK on %s ↑
sniFanWornWarningThe rotational speed of the fan is almost critical.
9002 MINOR The rotational speed of the fan is almost critical on %s ↑
次の表は、DESKTRAP-MIBのトラップを掲載して、概要を示したものです。DeskView Trap-Agentからのトラップです。
sniFanWornCriticalThe rotational speed of the fan is critical.
9003 CRITICAL The rotational speed of the fan is critical on %s ↑
sniVoltageOkThe voltage monitor is functioning.
11001 INFORMATIONAL The voltage monitor is functioning on %s ↑
sniVoltageWarningThe voltage is almost critical.
11002 MINOR The voltage is almost critical on %s ↑
sniVoltageCriticalThe voltage monitor is not functioning or thevoltage is critical.
11003 CRITICALThe voltage monitor is not functioning or the voltage is criticalon %s
↑
sniWatchdogOkThe functionality of the operating system watchdogis guaranteed.
12001 INFORMATIONALThe functionality of the operating system watchdog isguaranteed on %s
↑
sniWatchdogCriticalThe operating system watchdog caused too manyconsecutive system reboots and will be deactivated.
12003 CRITICALThe operating system watchdog caused too many consecutivesystem reboots and will be deactivated on %s
↑
sniInternalErrorMessages for system monitoring got lost becausethey could not be buffered!. The buffer has overrunor the harddisk was full.
13001 MINORMessages for system monitoring got lost because they couldnot be buffered!. The buffer has overrun or the harddisk wasfull on %s.
↑
sniBIOSErrorLogOKBIOS error log contains no current entries
14001 INFORMATIONAL BIOS error log contains no current entries on %s ↑
sniBIOSErrorLogWarningBIOS reported a non-critical problem
14002 MINOR BIOS reported a non-critical problem on %s ↑
sniBIOSErrorLogCriticalBIOS reported a critical error
14003 CRITICAL BIOS reported a critical error on %s ↑
sniAOLPOSTCriticalPower On Self Test (POST) error.
15003 CRITICAL Power On Self Test (POST) error on %s ↑
sniAOLWatchdogCriticalThe operating system may be hung or thecomputer failed to boot.
16003 CRITICALThe operating system may be hung or the computer failed toboot on %s
↑
sniAOLCoverOpenedThe cover was opened.
17003 CRITICAL The cover was opened on %s ↑
sniAOLCPUMissingCriticalThe processor was removed from the computer.
18003 CRITICAL The processor was removed from the computer %s ↑
sniAOLHeartbeatCriticalThe computer is no longer available. (PresenceHeartbeat Expired).
20003 CRITICALThe computer %s is no longer available. (Presence HeartbeatExpired)
↑
sniFreeDiskSpaceOKFree hard disk space is sufficient.
21001 INFORMATIONAL Free hard disk space is sufficient on %s. ↑
sniFreeDiskSpaceWarningFree hard disk space is low.
21002 MINOR Free hard disk space is low on %s. ↑
sniFreeDiskSpaceErrorFree hard disk space is extremely low.
21003 CRITICAL Free hard disk space is extremely low on %s. ↑
sniMemoryChangesOKThe memory size has not changed.
22001 INFORMATIONAL The memory size has not changed on %s. ↑
sniMemoryChangesWarningThe memory size increased.
22002 MINOR The memory size increased on %s. ↑
sniMemoryChangesErrorThe memory size decreased.
22003 CRITICAL The memory size decreased on %s. ↑
sniDeviceChangesOKNo changes in devices.
23001 INFORMATIONAL No changes in devices on %s. ↑
sniDeviceChangesWarningA device was added to the system.
23002 MINOR A device was added to system %s. ↑
sniDeviceChangesErrorA device was removed from the system.
23003 CRITICAL A device was removed from system %s. ↑
sniAOLVoltage_Fan_TemperatureCriticalA Voltage/Fan/Temperature is operating out ofspecification.
24003 CRITICALA Voltage/Fan/Temperature is operating out of specificationon %s
↑
sniAOLLANLeashCriticalThe computer was recently reconnected to thenetwork.
25003 CRITICAL The computer was recently reconnected to the network on %s ↑
sniAOLProcessorTemperatureCriticalThe processor temperature is out of specification.
26003 CRITICAL The processor temperature is out of specification on %s ↑
sniAOLProcessor0MissingCriticalThe processor P0 was removed from the computer.
28003 CRITICAL The processor P0 was removed from the computer on %s ↑
sniAOLProcessor1MissingCriticalThe processor P1 was removed from the computer.
29003 CRITICAL The processor P1 was removed from the computer on %s ↑
sniAOLVoltage_FanCriticalA Voltage/Fan is operating out of specification.
30003 CRITICAL A Voltage/Fan is operating out of specification on %s ↑
sniAOLVoltageCriticalA Voltage is operating out of specification.
31003 CRITICAL A Voltage is operating out of specification on %s ↑
sniAOLFanCriticalA Fan is operating out of specification.
32003 CRITICAL A Fan is operating out of specification on %s ↑
sniAOLFan_TemperatureCriticalA Fan/Temperature is operating out of specification.
33003 CRITICAL A Fan/Temperature is operating out of specification on %s ↑
sniAOLVoltage_TemperatureCriticalA Voltage/Temperature is operating out ofspecification.
34003 CRITICAL A Voltage/Temperature is operating out of specification on %s ↑
sniAOLNICSMBusSlotCriticalNIC with Capelookout has been plugged into a PCIslot without SMBus connection.
35003 CRITICALNIC with Capelookout has been plugged into a PCI slotwithout SMBus connection on %s
↑
sniAOLPresencePongCriticalReceived a presence pong reply.
36003 CRITICAL Received a presence pong reply on %s ↑
sniAOLHardwareMonitorCriticalHardware Monitor has detected an external event.
37003 CRITICAL Hardware Monitor has detected an external event on %s ↑
sniAOL1_5VGTLVoltageCritical+1.5 GTL Voltage is out of specification.
38003 CRITICAL +1.5 GTL Voltage is out of specification on %s ↑
sniAOLCPUCoreVoltageCriticalCPU Core Voltage is out of specification.
39003 CRITICAL CPU Core Voltage is out of specification on %s ↑
sniAOL3_3VStandbyCritical+3.3V Standby Voltage is out of specification.
40003 CRITICAL +3.3V Standby Voltage is out of specification on %s ↑
sniAOL5VoltageCritical+5V Voltage is out of specification.
41003 CRITICAL +5V Voltage is out of specification on %s ↑
sniAOLHardwareMonitorInternalTemperatureCriticalHardware Monitor Internal Temperature is out ofspecification.
42003 CRITICALHardware Monitor Internal Temperature is out of specificationon %s
↑
sniAOLCPUDiodeSensorCriticalCPU Diode Sensor is operating out of specification.
43003 CRITICAL CPU Diode Sensor is operating out of specification on %s ↑
sniAOLCPUFanCriticalCPU Fan is operating out of specification.
44003 CRITICAL CPU Fan is operating out of specification on %s ↑
sniAOLChassisFanCriticalChassis Fan is operating out of specification.
45003 CRITICAL Chassis Fan is operating out of specification on %s ↑
sniAOL12VoltageCritical+12V is operating out of specification.
46003 CRITICAL +12V is operating out of specification on %s ↑
sniAOL3_3VoltageCritical+3.3V is operating out of specification.
47003 CRITICAL +3.3V is operating out of specification on %s ↑
sniAOLCPUDiodeCriticalOpen/Short has occurred in the CPU Diode
48003 CRITICAL Open/Short has occurred in the CPU Diode Sensor on %s ↑
sniAOL2_5VoltageCritical+2.5V is operating out of specification.
49003 CRITICAL +2.5V is operating out of specification on %s ↑
sniAOLAmbientTemperatureCriticalAmbient temperature is out of specification.
50003 CRITICAL Ambient temperature is out of specification on %s ↑
sniAOLRemoteTemperatureCriticalRemote Temperature is out of specification.
51003 CRITICAL Remote Temperature is out of specification on %s ↑
sniAOLUndockEventCriticalSurprised undock event (no information is
52003 CRITICAL Surprised undock event (no information is available) on %s ↑
sniFreeSystemDiskSpaceOKFree hard disk space on system disk is sufficient.
56001 INFORMATIONAL Free hard disk space on system disk is sufficient on %s. ↑
sniFreeSystemDiskSpaceWarningFree hard disk space on system disk is low.
56002 MINOR Free hard disk space on system disk is low on %s. ↑
sniFreeSystemDiskSpaceError Free hard diskspace on system disk is extremely low.
56003 CRITICAL Free hard disk space on system disk is extremely low on %s. ↑
sniLeaseExpirationOKThe lease contract has not yet expired or noexpiration date has been set.
57001 INFORMATIONALThe lease contract has not yet expired or no expiration datehas been set on %s.
↑
sniLeaseExpirationWarningThe lease contract will expire soon.
57002 MINOR The lease contract will expire soon on %s. ↑
sniLeaseExpirationErrorThe lease contract has expired.
57003 CRITICAL The lease contract has expired on %s. ↑
sniProcessorChangeOKNo processor change determined.
58001 INFORMATIONAL No processor change determined on %s. ↑
sniProcessorChangeWarningA processor has also been installed or replaced.
58002 MINOR A processor has also been installed or replaced on %s. ↑
sniProcessorChangeErrorA processor has been removed.
58003 CRITICAL A processor has been removed on %s. ↑
DPT-SCSI-MIB (dptscsi.mib)
次の表は、DPT-SCSI-MIBのトラップを掲載して、概要を示したものです。Adaptec's I2O-based RAID Cardからのトラップです。詳細についてはRAIDコントローラの説明書を参照してください。
表14:ADAPTECDURALINK-MIB トラップ(ENTERPRISE : enterprises.1597)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
dptHbaTemperatureVeryHighTrapVery high temperature on controller
400 CRITICAL Very high temperature on controller %d
dptArrayStatusChangeFailedTrapArray failed
401 CRITICAL Array failed on Controller %d Bus %d ID %d LUN %d.
dptHbaVoltageChangeTrap5V Voltage outside range on controller
300 MAJOR 5V Voltage status is now %d on controller %d
dptHbaTemperatureHighTrapHigh temperature on controller
301 MINOR High temperature on controller %d
dptHbaEccRAMErrorUncorrectableTrapController detected an ECC RAM error that couldnot be corrected
302 MAJOR Uncorrectable ECC error found on controller %d
dptArrayStatusChangeDegradedTrapArray degraded
303 MAJOR Array on Controller %d Bus %d ID %d LUN %d running degraded.
dptDevReqSenseSeriousErrorTrapSerious: Request sense data received.
304 MAJORSerious: Request sense data for controller %d Bus %d ID %dLUN %d.
dptDevArrayDataInconsistencyTrapArray data inconsistency found.
305 MAJOR Array Data Inconsistency: Controller %d Bus %d ID %d LUN %d.
dptHbaErrorTrapcontroller error found.
306 MAJOR controller %d reported a non-SCSI related error.
dptDevFailedTrapUnprotected drive has failed.
307 MAJOR Drive failure on controller %d Bus %d ID %d LUN %d.
dptDevSmartFailedTrapSMART failure reported.
308 MAJORSMART failure on controller %d Bus %d ID %d LUN %dreported.
dptHbaAuxVoltageChangeTrapAuxiliary voltage outside range on controller
309 MAJOR An auxiliary voltage status is now %d on controller %d
dptHbaVoltageChange2Trap5V Voltage outside range on controller
310 MAJOR 5V Voltage status is now %s on controller %d
dptHbaAuxVoltageChange2TrapAuxiliary voltage outside range on controller
311 MAJOR An auxiliary voltage status is now %s on controller %d
dptHbaEccRAMErrorCorrectedTrapECC RAM Error detected and corrected.
200 MINOR Correctable ECC RAM Error detected on controller %d
dptDevBlockReassignedTrapDisk block was reassigned
201 MINOR Block %d reassigned: Controller %d Bus %d ID %d LUN %d
dptDevReqSenseErrorTrapWarning: request sense data received.
202 MINORWarning: Request sense data for controller %d Bus %d ID %dLUN %d.
dptHbaVoltageNormalTrapNormal 5V voltage on controller
100 INFORMATIONAL Normal 5V voltage restored on controller %d
dptHbaTemperatureNormalTrapNormal temperature on controller
101 INFORMATIONAL Normal temperature restored on controller %d
dptHbaEccRAMErrorNotFoundTrapECC RAM Error detected but not found on correction.
102 INFORMATIONALECC RAM Error detected at %d on controller %d, but notfound.
dptDevStatusChangedTrapDevice status change
103 INFORMATIONAL Device status on Controller %d Bus %d ID %d LUN %d : %d.
dptDevReqSenseTrapRequest sense received from controller.
104 INFORMATIONAL Request sense data for controller %d Bus %d ID %d LUN %d.
dptArrayChangeTrapArray change.
105 INFORMATIONAL Array change on controller %d Bus %d ID %d LUN %d.
dptBatteryChangeTrapBattery status change.
106 INFORMATIONAL Battery status is now %d on controller %d.
dptHbaAuxVoltageNormalTrapNormal auxiliary voltage on controller
107 INFORMATIONAL Normal auxiliary voltage restored on controller %d
dptHbaNoSparesTrapNo hot spares detected on controller
108 INFORMATIONALNo available hot spares were detected during a scan oncontroller %d
dptDevStatusChanged2TrapDevice status change
109 INFORMATIONAL Device status on Controller %d Bus %d ID %d LUN %d : %s.
dptBatteryChange2TrapBattery status change.
110 INFORMATIONAL Battery status is now %s on controller %d.
dptOtherTrapController generated an event
14 INFORMATIONAL Controller generated event: %s
MYLEXRAID-MIB (Mlxraid.mib)
表15:MYLEXRAID-MIB トラップ(ENTERPRISE : enterprises.1608.1.1.1.9.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
physdevOnlineA hard disk has been placed online.
1 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] A hard disk has been placed online.
physdevHotspareA hard disk added as hot spare.
2 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] A hard disk added as hot spare.
physdevHardErrorHard disk error found.
3 MINOR [ctl: %d chn: %d tgt: %d :] Hard disk error found.
physdevPfaHard disk PFA condition found, this disk may fail soon.
4 MINOR[ctl: %d chn: %d tgt: %d :] Hard disk PFA condition found, thisdisk may fail soon.
physdevAutoRebuildStartAn automatic rebuild has started.
5 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] An automatic rebuild has started.
physdevManualRebuildStartA rebuild has started.
6 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] A rebuild has started.
physdevRebuildDoneRebuild is over.
7 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Rebuild is over.
physdevRebuildCanceledRebuild is cancelled.
8 MINOR [ctl: %d chn: %d tgt: %d :] Rebuild is cancelled.
physdevRebuildErrorRebuild stopped with error.
9 MAJOR [ctl: %d chn: %d tgt: %d :] Rebuild stopped with error.
physdevRebuildNewdevFailedRebuild stopped with error. New device failed.
10 MAJOR[ctl: %d chn: %d tgt: %d :] Rebuild stopped with error. Newdevice failed.
physdevRebuildSysdevFailedRebuild stopped because logical drive failed.
11 MAJOR[ctl: %d chn: %d tgt: %d :] Rebuild stopped because logical drivefailed.
physdevDeadA hard disk has failed.
12 MAJOR [ctl: %d chn: %d tgt: %d :] A hard disk has failed.
physdevFoundA new hard disk has been found.
13 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] A new hard disk has been found.
physdevGoneA hard disk has been removed.
14 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] A hard disk has been removed.
physdevUnconfiguredA previously configured disk is now available.
15 INFORMATIONAL[ctl: %d chn: %d tgt: %d :] A previously configured disk is nowavailable.
physdevExpandcapacityStartExpand Capacity Started.
16 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Expand Capacity Started.
physdevExpandcapacityDoneExpand Capacity Completed.
17 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Expand Capacity Completed.
physdevExpandcapacityErrorExpand Capacity Stopped with error.
18 MAJOR [ctl: %d chn: %d tgt: %d :] Expand Capacity Stopped with error.
physdevCommandTimeoutSCSI command timeout on hard device.
19 MINOR[ctl: %d chn: %d tgt: %d :] SCSI command timeout on harddevice.
physdevCommandAbortSCSI command abort on hard disk.
20 CRITICAL [ctl: %d chn: %d tgt: %d :] SCSI command abort on hard disk.
physdevCommandRetriedSCSI command retried on hard disk.
21 MINOR [ctl: %d chn: %d tgt: %d :] SCSI command retried on hard disk.
physdevParityErrorParity error found.
22 MINOR [ctl: %d chn: %d tgt: %d :] Parity error found.
physdevSoftErrorSoft error found.
23 MINOR [ctl: %d chn: %d tgt: %d :] Soft error found.
physdevMiscErrorMisc error found.
24 MINOR [ctl: %d chn: %d tgt: %d :] Misc error found.
physdevResetSCSI device reset.
25 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] SCSI device reset.
physdevActivespareActive spare found.-
26 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Active spare found.-
physdevWarmspareWarm spare found.-
27 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Warm spare found.-
physdevReqsenseRequest Sense Data available.
28 MAJOR [ctl: %d chn: %d tgt: %d :] Request Sense Data available.
physdevInitStartedInitialization started.
29 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Initialization started.
physdevInitDoneInitialization completed.
30 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] Initialization completed.
physdevInitFailedInitialization failed.
31 MINOR [ctl: %d chn: %d tgt: %d :] Initialization failed.
physdevInitCanceledInitialization canceled.
32 MAJOR [ctl: %d chn: %d tgt: %d :] Initialization canceled.
physdevWriterecDeadA hard disk failed because write recovery failed.
33 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because writerecovery failed.
physdevResetDeadA hard disk failed because SCSI bus reset failed.
34 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because SCSI busreset failed.
physdevDblccDeadA hard disk failed because double check conditionoccured.
35 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because doublecheck condition occured.
physdevRemovedDeadA hard disk failed because device is missing.
36 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because device ismissing.
physdevGrosserrDeadA hard disk failed because of gross error on SCSIprocessor.
37 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because of grosserror on SCSI processor.
physdevBadtagDeadA hard disk failed because of bad tag from the device.
38 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because of bad tagfrom the device.
physdevScsitmoDeadA hard disk failed because command to the devicetimed out.
39 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because commandto the device timed out.
physdevSysresetDeadA hard disk failed because of the system reset.
40 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because of thesystem reset.
physdevBsyparDeadA hard disk failed because of busy status or parityerror.
41 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because of busystatus or parity error.
physdevBycmdDeadA hard disk set to failed state by host.
42 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk set to failed state byhost.
physdevSeltmoDeadA hard disk failed because access to the devicemet with a selection time out.
43 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because access tothe device met with a selection time out.
physdevSeqerrDeadA hard disk failed because of a sequence error inthe SCSI bus phase handling.
44 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because of asequence error in the SCSI bus phase handling.
次の表は、MYLEXRAID-MIBのトラップを掲載して、概要を示したものです。Mylex Disk Array Controllerからのトラップです。詳細についてはRAIDコントローラの説明書を参照してください。RAID Manager(GAM:Global Array Manager)
physdevUnknownstsDeadA hard disk failed because device returned anunknown status.
45 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because devicereturned an unknown status.
physdevNotrdyDeadA hard disk failed because device is not ready.
46 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because device isnot ready.
physdevMissingDeadA hard disk failed because device was not found onstart up.
47 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because devicewas not found on start up.
physdevCodwrfailDeadA hard disk failed because write operation of the'Configuration On Disk' failed.
48 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because writeoperation of the 'Configuration On Disk' failed.
physdevBdtwrfailDeadA hard disk failed because write operation of 'BadData Table' failed.
49 MAJOR[ctl: %d chn: %d tgt: %d :] A hard disk failed because writeoperation of 'Bad Data Table' failed.
physdevOfflinePhysical device status changed to offline.
50 MINOR[ctl: %d chn: %d tgt: %d :] Physical device status changed tooffline.
physdevStandbyPhysical device status changed to Hot Spare.
51 MINOR[ctl: %d chn: %d tgt: %d :] Physical device status changed toHot Spare.
physdevRebuildPhysical device status changed to rebuild.
52 MINOR[ctl: %d chn: %d tgt: %d :] Physical device status changed torebuild.
physdevIdMismatchPhysical device ID did not match.
53 MINOR [ctl: %d chn: %d tgt: %d :] Physical device ID did not match.
physdevFailedStartPhysical device failed to start.
54 MINOR [ctl: %d chn: %d tgt: %d :] Physical device failed to start.
physdevOffsetSetPhysical device negotiated different offset than config.
55 MINOR[ctl: %d chn: %d tgt: %d :] Physical device negotiated differentoffset than config.
physdevSetBusWidthPhysical device negotiated different bus width thanconfig.
56 MINOR[ctl: %d chn: %d tgt: %d :] Physical device negotiated differentbus width than config.
physdevMissingOnstartupPhysical drive missing on startup.
57 MAJOR [ctl: %d chn: %d tgt: %d :] Physical drive missing on startup.
physdevRebuildStartFailedRebuild startup failed due to lower disk capacity.
58 MINOR[ctl: %d chn: %d tgt: %d :] Rebuild startup failed due to lowerdisk capacity.
physdevMovingToOtherChnPhysical drive is switching from a channel to theother channel.
59 MINOR[ctl: %d chn: %d tgt: %d :] Physical drive is switching from achannel to the other channel.
physdevOfflineDeviceMadeOnlineTemporary-Dead physical drive is automaticallymade online.
60 MAJOR[ctl: %d chn: %d tgt: %d :] Temporary-Dead physical drive isautomatically made online.
physdevStandbyRebuildStartA standby rebuild has started.
61 INFORMATIONAL [ctl: %d chn: %d tgt: %d :] A standby rebuild has started.
physdevHotSpareSmallerHot spare replaced with a smaller capacity drive.
62 INFORMATIONAL[ctl: %d chn: %d tgt: %d :] Hot spare replaced with a smallercapacity drive.
ppilotFailbackOccurredA failback event has occurred.
63 MINOR [ctl: %d chn: %d tgt: %d :] A failback event has occurred.
ppilotFailoverOccurredA failover event has occurred.
64 MINOR [ctl: %d chn: %d tgt: %d :] A failover event has occurred.
ppilotSysdevOnlineA logical disk has come online.
65 MINOR [ctl: %d chn: %d tgt: %d :] A logical disk has come online.
ppilotSysdevPathOfflineAll paths to a logical disk have gone offline.
66 CRITICAL[ctl: %d chn: %d tgt: %d :] All paths to a logical disk have goneoffline.
fibredevLoopidSoftaddrOccurredDevice Loop Id Conflict (Soft Addressing)
96 MAJOR[ctl: %d chn: %d :] Device Loop Id Conflict (Soft Addressing)Detected.
sysdevCheckStartConsistency check is started.
128 INFORMATIONAL [ctl: %d logdrv: %d :] Consistency check is started.
sysdevCheckDoneConsistency check is finished.
129 INFORMATIONAL [ctl: %d logdrv: %d :] Consistency check is finished.
sysdevCheckCanceledConsistency check is cancelled.
130 MINOR [ctl: %d logdrv: %d :] Consistency check is cancelled.
sysdevCheckErrorConsistency check on logical drive error.
131 MAJOR [ctl: %d logdrv: %d :] Consistency check on logical drive error.
sysdevCheckSysdevFailedConsistency check on logical drive failed.
132 MAJOR [ctl: %d logdrv: %d :] Consistency check on logical drive failed.
sysdevCheckPhysdevFailedConsistency check failed due to physical devicefailure.
133 MAJOR[ctl: %d logdrv: %d :] Consistency check failed due to physicaldevice failure.
sysdevOfflineLogical drive has been made offline.
134 MAJOR [ctl: %d logdrv: %d :] Logical drive has been made offline.
sysdevCriticalLogical drive is critical.
135 MAJOR [ctl: %d logdrv: %d :] Logical drive is critical.
sysdevOnlineLogical drive has been placed online.
136 INFORMATIONAL [ctl: %d logdrv: %d :] Logical drive has been placed online.
sysdevAutoRebuildStartAn automatic rebuild has started on logical drive.
137 INFORMATIONAL[ctl: %d logdrv: %d :] An automatic rebuild has started onlogical drive.
sysdevManualRebuildStartA manual rebuild has started on logical drive.
138 INFORMATIONAL[ctl: %d logdrv: %d :] A manual rebuild has started on logicaldrive.
sysdevRebuildDoneRebuild on logical drive is over.
139 INFORMATIONAL [ctl: %d logdrv: %d :] Rebuild on logical drive is over.
sysdevRebuildCanceledRebuild on logical drive is cancelled.
140 MINOR [ctl: %d logdrv: %d :] Rebuild on logical drive is cancelled.
sysdevRebuildErrorRebuild stopped with error.
141 MAJOR [ctl: %d logdrv: %d :] Rebuild stopped with error.
sysdevRebuildNewdevFailedRebuild stopped with error. New device failed.
142 MAJOR[ctl: %d logdrv: %d :] Rebuild stopped with error. New devicefailed.
sysdevRebuildSysdevFailedRebuild stopped because logical drive failed.
143 MAJOR[ctl: %d logdrv: %d :] Rebuild stopped because logical drivefailed.
sysdevInitStartedLogical drive initialization started.
144 INFORMATIONAL [ctl: %d logdrv: %d :] Logical drive initialization started.
sysdevInitDoneLogical drive initialization done.
145 INFORMATIONAL [ctl: %d logdrv: %d :] Logical drive initialization done.
sysdevInitCanceledLogical drive initialization cancelled.
146 MINOR [ctl: %d logdrv: %d :] Logical drive initialization cancelled.
sysdevInitFailedLogical drive initialization failed.
147 MAJOR [ctl: %d logdrv: %d :] Logical drive initialization failed.
sysdevFoundA logical drive has been found.
148 INFORMATIONAL [ctl: %d logdrv: %d :] A logical drive has been found.
sysdevGoneA logical drive has been deleted.
149 INFORMATIONAL [ctl: %d logdrv: %d :] A logical drive has been deleted.
sysdevExpandcapacityStartExpand Capacity Started.
150 INFORMATIONAL [ctl: %d logdrv: %d :] Expand Capacity Started.
sysdevExpandcapacityDoneExpand Capacity Completed.
151 INFORMATIONAL [ctl: %d logdrv: %d :] Expand Capacity Completed.
sysdevExpandcapacityErrorExpand Capacity stopped with error.
152 MAJOR [ctl: %d logdrv: %d :] Expand Capacity stopped with error.
sysdevBadblockBad Blocks found.
153 CRITICAL [ctl: %d logdrv: %d :] Bad Blocks found.
sysdevSizechangedSystem drive size changed.
154 INFORMATIONAL [ctl: %d logdrv: %d :] System drive size changed.
sysdevTypechangedSystem drive type changed.
155 INFORMATIONAL [ctl: %d logdrv: %d :] System drive type changed.
sysdevBaddatablockBad data blocks found. Possible data loss.
156 MAJOR [ctl: %d logdrv: %d :] Bad data blocks found. Possible data loss.
sysdevWrLunMapSystem drive LUN mapping has been written to config.
157 MINOR[ctl: %d :] System drive LUN mapping has been written toconfig.
sysdevDatareadFromBlockInBdtAttempt to read data from block that is marked inBad Data Table
158 MAJOR[ctl: %d logdrv: %d :] Attempt to read data from block that ismarked in Bad Data Table
sysdevDataForBlockLostData for Disk Block has been lost due to LogicalDrive problem
159 MAJOR[ctl: %d logdrv: %d :] Data for Disk Block has been lost due toLogical Drive problem
sysdevOfflineDeviceMadeAvailableWithDatalossTemporary-Offline RAID5/RAID3 array is availableto the user again with the possibility of data loss inthe array.
160 MAJOR[ctl: %d logdrv: %d :] Temporary-Offline RAID5/RAID3 array isavailable to the user again with the possibility of data loss inthe array.
sysdevOfflineDeviceMadeAvailableTemporary-Offline RAID0+1/RAID1/RAID0/JBODarray is available to the user again.
161 MAJOR[ctl: %d logdrv: %d :] Temporary-OfflineRAID0+1/RAID1/RAID0/JBOD array is available to the useragain.
sysdevStandbyRebuildStartA standby rebuild has started on a logical drive.
162 INFORMATIONAL[ctl: %d logdrv: %d :] A standby rebuild has started on a logicaldrive.
sysdevBgInitStartedLogical drive background initialization started.
176 INFORMATIONAL[ctl: %d logdrv: %d :] Logical drive background initializationstarted.
sysdevBgInitStoppedLogical drive background initialization stopped.
177 INFORMATIONAL[ctl: %d logdrv: %d :] Logical drive background initializationstopped.
sysdevBgInitPausedLogical drive background initialization paused.
178 INFORMATIONAL[ctl: %d logdrv: %d :] Logical drive background initializationpaused.
sysdevBgInitRestartedLogical drive background initialization restarted.
179 INFORMATIONAL[ctl: %d logdrv: %d :] Logical drive background initializationrestarted.
sysdevBgInitFailedLogical drive background initialization failed.
180 MAJOR[ctl: %d logdrv: %d :] Logical drive background initializationfailed.
sysdevBgInitCompletedLogical drive background initialization completed.
181 INFORMATIONAL[ctl: %d logdrv: %d :] Logical drive background initializationcompleted.
fmtfanFailedFan failure.
256 MAJOR [ctl: %d enclosure: %d unit: %d :] Fan failure.
fmtfanOkFan has been restored.
257 INFORMATIONAL [ctl: %d enclosure: %d unit: %d :] Fan has been restored.
aemiFanFailedFan failure.
258 MAJOR [ctl: %d chn: %d tgt: %d Fan: %d :] Fan failure.
fmtfanNotpresentStorage cabinet fan is not present.
259 INFORMATIONAL [ctl: %d enclosure: %d :] Storage cabinet fan is not present.
fmtpowerFailedPower supply failure.
272 MAJOR [ctl: %d enclosure: %d unit: %d :] Power supply failure.
fmtpowerOkPower supply has been restored.
273 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Power supply has beenrestored.
aemiPwrSupplyFailedPower supply failure.
274 MAJOR[ctl: %d chn: %d tgt: %d Power Supply: %d :] Power supplyfailure.
fmtpowerNotpresentStorage cabinet power supply is not present.
275 INFORMATIONAL[ctl: %d enclosure: %d :] Storage cabinet power supply is notpresent.
fmtheatBadOver temperature. Temperature is above 70degrees Celsius.
288 MAJOR[ctl: %d chn: %d tgt: %d Heat Sensor: %d :] Over temperature.Temperature is above 70 degrees Celsius.
fmtheatCriticalTemperature is above 50 degrees Celsius.
289 MINOR[ctl: %d enclosure: %d unit: %d :] Temperature is above 50degrees Celsius.
fmtheatOkNormal temperature has been restored.
290 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Normal temperature has beenrestored.
aemiOverTemperatureOver temperature.
291 MAJOR [ctl: %d chn: %d tgt: %d Heat Sensor: %d :] Over temperature.
fmtheatNotpresentStorage cabinet temperature sensor is not present.
292 INFORMATIONAL[ctl: %d enclosure: %d :] Storage cabinet temperature sensor isnot present.
fmtstwkFailedStorage Works enclosure reported failure state.
304 MAJOR[ctl: %d chn: %d :] Storage Works enclosure reported failurestate.
fmtstwkCriticalStorage Works enclosure reported critical state.
305 MINOR[ctl: %d chn: %d :] Storage Works enclosure reported criticalstate.
fmtstwkOkStorage Works enclosure reported normal state.
306 INFORMATIONAL[ctl: %d chn: %d :] Storage Works enclosure reported normalstate.
fmtUpsDisabledUninterruptible Power Supply Disabled.
307 INFORMATIONAL [ctl: %d :] Uninterruptible Power Supply Disabled.
fmtUpsAcFailUninterruptible Power Supply AC Failed.
308 INFORMATIONAL [ctl: %d :] Uninterruptible Power Supply AC Failed.
fmtUpsBatLowUninterruptible Power Supply Battery Low.
309 MINOR [ctl: %d :] Uninterruptible Power Supply Battery Low.
fmtUpsFailedUninterruptible Power Supply Failed.
310 MAJOR [ctl: %d :] Uninterruptible Power Supply Failed.
fmtUpsOkUninterruptible Power Supply Normal.
311 INFORMATIONAL [ctl: %d :] Uninterruptible Power Supply Normal.
enclfanFailedFan failure.
320 MAJOR [ctl: %d enclosure: %d unit: %d :] Fan failure.
enclfanOkFan has been restored.
321 INFORMATIONAL [ctl: %d enclosure: %d unit: %d :] Fan has been restored.
enclfanNotpresentFan is not present.
322 INFORMATIONAL [ctl: %d enclosure: %d unit: %d :] Fan is not present.
enclpowerFailedPower supply failure.
323 MAJOR [ctl: %d enclosure: %d unit: %d :] Power supply failure.
enclpowerOkPower supply has been restored.
324 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Power supply has beenrestored.
enclpowerNotpresentPower supply is not present.
325 INFORMATIONAL [ctl: %d enclosure: %d unit: %d :] Power supply is not present.
enclheatBadTemperature is over safe limit. Failure imminent.
326 MAJOR[ctl: %d enclosure: %d unit: %d :] Temperature is over safe limit.Failure imminent.
enclheatCriticalTemperature is above working limit.
327 MINOR[ctl: %d enclosure: %d unit: %d :] Temperature is above workinglimit.
enclheatOkNormal temperature has been restored.
328 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Normal temperature has beenrestored.
enclheatNotpresentTemperature sensor is not present.
329 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Temperature sensor is notpresent.
enclaccessCriticalEnclosure access critical.
330 MINOR [ctl: %d enclosure: %d :] Enclosure access critical.
enclaccessOkEnclosure access has been restored.
331 INFORMATIONAL [ctl: %d enclosure: %d :] Enclosure access has been restored.
enclaccessOfflineEnclosure access is offline.
332 MAJOR [ctl: %d enclosure: %d unit: %d :] Enclosure access is offline.
enclsesSoftaddrOccurredEnclosure Soft Addressing Detected.
333 MAJOR [ctl: %d enclosure: %d :] Enclosure Soft Addressing Detected.
enclaccessReadyEnclosure services ready
334 INFORMATIONAL [ctl: %d :] Enclosure services ready
enclheatUnknownAccess to temperature sensor has been lost.
335 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Access to temperature sensorhas been lost.
enclpowerUnknownAccess to power supply status information hasbeen lost.
336 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Access to power supplystatus information has been lost.
enclfanUnknownAccess to fan status information has been lost.
337 INFORMATIONAL[ctl: %d enclosure: %d unit: %d :] Access to fan statusinformation has been lost.
systemStartedArray management server software startedsuccessfully.
384 INFORMATIONAL Array management server software started successfully.
ctldevWritebackErrorWrite back error.
385 MAJOR [ctl: %d :] Write back error.
ctldevStateTableFullInternal log structures getting full,PLEASE SHUTDOWNAND RESET THE SYSTEM IN THE NEAR FUTURE.
386 MINOR[ctl: %d :] Internal log structures getting full,PLEASESHUTDOWN AND RESET THE SYSTEM IN THE NEARFUTURE.
ctldevDeadController is dead. System is disconnecting fromthis controller.
388 CRITICAL[ctl: %d :] Controller is dead. System is disconnecting fromthis controller.
ctldevResetController has been reset.
389 MINOR [ctl: %d :] Controller has been reset.
ctldevFoundController is found.
390 INFORMATIONAL [ctl: %d :] Controller is found.
ctldevGoneController is gone. System is disconnecting fromthis controller.
391 CRITICAL[ctl: %d :] Controller is gone. System is disconnecting fromthis controller.
ctldevBbuFoundBBU Present.
392 INFORMATIONAL [ctl: %d :] BBU Present.
ctldevBbuPowerLowBBU Power Low.
393 MINOR [ctl: %d :] BBU Power Low.
ctldevBbuPowerOkBBU Power OK.
394 INFORMATIONAL [ctl: %d :] BBU Power OK.
ctldevPowerOffController is gone. System is disconnecting fromthis controller.
395 CRITICAL[ctl: %d :] Controller is gone. System is disconnecting fromthis controller.
ctldevPowerOnController powered on
396 INFORMATIONAL [ctl: %d :] Controller powered on
ctldevOnlineController is online.
397 INFORMATIONAL [ctl: %d :] Controller is online.
ctldevOfflineController is gone. System is disconnecting fromthis controller.
398 CRITICAL[ctl: %d :] Controller is gone. System is disconnecting fromthis controller.
ctldevCriticalController's partner is gone, controller is in failovermode now.
399 MINOR[ctl: %d :] Controller's partner is gone, controller is in failovermode now.
ctldevBbuRecondStartBBU reconditioning is started.
400 INFORMATIONAL [ctl: %d :] BBU reconditioning is started.
ctldevBbuRecondDoneBBU reconditioning is finished.
401 INFORMATIONAL [ctl: %d :] BBU reconditioning is finished.
ctldevBbuRecondAbortBBU reconditioning is canceled.
402 INFORMATIONAL [ctl: %d :] BBU reconditioning is canceled.
ctldevInstallationAbortedInstallation aborted.
403 MAJOR [ctl: %d :] Installation aborted.
ctldevFirmwareMismatchController firmware mismatch.
404 MAJOR [ctl: %d chn: %d tgt: %d :] Controller firmware mismatch.
ctldevBbuNoresponseBBU removed.
405 MINOR [ctl: %d chn: %d tgt: %d :] BBU removed.
ctldevWarmBootErrorWARM BOOT failed.
406 MAJOR [ctl: %d chn: %d tgt: %d :] WARM BOOT failed.
ctldevBbuCalibrateStartBBU calibration cycle started.
407 INFORMATIONAL [ctl: %d :] BBU calibration cycle started.
ctldevBbuCalibrateDoneBBU calibration cycle finished.
408 INFORMATIONAL [ctl: %d :] BBU calibration cycle finished.
ctldevBbuCalibrateAbortBBU calibration cycle is canceled.
409 INFORMATIONAL [ctl: %d :] BBU calibration cycle is canceled.
ctldevBbuNoBatteryBBU battery not present.
410 INFORMATIONAL [ctl: %d :] BBU battery not present.
ctldevConservCacheModeController entered Conservative Cache Mode.
411 MINOR [ctl: %d :] Controller entered Conservative Cache Mode.
ctldevNormalCacheModeController entered Normal Cache Mode.
412 MINOR [ctl: %d :] Controller entered Normal Cache Mode.
ctldevDevStartCmpltController Device Start Complete.
413 MINOR [ctl: %d :] Controller Device Start Complete.
ctldevSoftEccCorrectedSoft ECC error Corrected.
414 MINOR [ctl: %d :] Soft ECC error Corrected.
ctldevHardEccCorrectedHard ECC error Corrected.
415 MINOR [ctl: %d chn: %d tgt: %d :] Hard ECC error Corrected.
ctldevBbuRecondNeededBBU Recondition Needed.
416 MAJOR [ctl: %d :] BBU Recondition Needed.
ctldevRemovedPtnrController's Partner Has Been Removed.
417 MINOR [ctl: %d :] Controller's Partner Has Been Removed.
ctldevBbuOutOfServiceBBU out of service.
418 MAJOR [ctl: %d :] BBU out of service.
ctldevUpdatePtnrStatusUpdated partner's status.
419 MINOR [ctl: %d :] Updated partner's status.
ctldevRelinquishPtnrRelinquished partner.
420 MINOR [ctl: %d :] Relinquished partner.
ctldevInsertedPtnrInserted Partner.
421 MINOR [ctl: %d :] Inserted Partner.
ctldevDualEnabledDual Controllers Enabled.
422 MINOR [ctl: %d :] Dual Controllers Enabled.
ctldevKillPtnrKilled Partner.
423 MINOR [ctl: %d :] Killed Partner.
ctldevNexusDual Controllers entered Nexus.
424 MINOR [ctl: %d :] Dual Controllers entered Nexus.
ctldevBadBootromImageController Boot ROM Image needs to be reloaded.
425 MAJOR [ctl: %d :] Controller Boot ROM Image needs to be reloaded.
ctldevBadMacAddressController is using default non-unique world-widename.
426 CRITICAL[ctl: %d :] Controller is using default non-unique world-widename.
ctldevMirrorRaceRecoveryFailedMirror Race recovery failed.
427 MAJOR [ctl: %d :] Mirror Race recovery failed.
ctldevMirrorCriticalDriveMirror Race on critical drive.
428 CRITICAL [ctl: %d :] Mirror Race on critical drive.
systemStartedNewSystem started.-
512 INFORMATIONAL System started.-
systemSizeTableFullSize table full.-
513 INFORMATIONAL Size table full.-
systemUserLoggedInUser logged in.-
514 INFORMATIONAL User logged in.-
systemUserLoggedOutUser logged out.-
515 INFORMATIONAL User logged out.-
systemAliveServer alive.
516 INFORMATIONAL Server alive.
systemDeadLost connection to server, or server is down.
517 MAJOR Lost connection to server, or server is down.
autobootChangedAutomatic reboot count has changed.
518 INFORMATIONAL [ctl: %d :] Automatic reboot count has changed.
channelFailedChannel Failed.
640 MINOR [ctl: %d chn: %d :] Channel Failed.
channelOkChannel Online.
641 MINOR [ctl: %d chn: %d :] Channel Online.
channelScsiBusDeadBack End SCSI Bus Dead.
642 MAJOR [ctl: %d chn: %d :] Back End SCSI Bus Dead.
channelScsiBusAliveBack End SCSI Bus Alive.
643 INFORMATIONAL [ctl: %d chn: %d :] Back End SCSI Bus Alive.
channelFiberDeadBack End Fibre Dead.
644 MAJOR [ctl: %d chn: %d :] Back End Fibre Dead.
channelFiberAliveBack End Fibre Alive.
645 INFORMATIONAL [ctl: %d chn: %d :] Back End Fibre Alive.
logEmptyEvent Log Empty.
700 MINOR [ctl: %d :] Event Log Empty.
logOutSyncEvent Log Entries Lost.
701 MINOR [ctl: %d :] Event Log Entries Lost.
logRequestSenseRequest Sense
702 MINOR [ctl: %d chn: %d tgt: %d :] Request Sense
logSetRtcSet Real Time Clock.
703 MINOR [ctl: %d chn: %d :] Set Real Time Clock.
cfgNewNew Configuration Received.
800 MINOR [ctl: %d :] New Configuration Received.
cfgClearConfiguration Cleared.
801 MINOR [ctl: %d :] Configuration Cleared.
cfgInvalidConfiguration Invalid.
802 MINOR [ctl: %d :] Configuration Invalid.
cfgCodAccessErrorConfiguration On Disk Access Error.
803 MINOR [ctl: %d :] Configuration On Disk Access Error.
cfgCodConvertedConfiguration On Disk Converted.
804 MINOR [ctl: %d :] Configuration On Disk Converted.
cfgCodImportFailedConfiguration On Disk Import Failed.
805 MINOR [ctl: %d :] Configuration On Disk Import Failed.
debugDumpGeneratedA Debug Dump exists on this system.
806 INFORMATIONAL [ctl: %d :] A Debug Dump exists on this system.
debugDumpGeneratedPartnerA Debug Dump exists on this system.
807 INFORMATIONAL [ctl: %d :] A Debug Dump exists on this system.
fatalHangInternal Controller is in the hung state.
896 MAJOR Internal Controller is in the hung state.
fatalBrkpInternal Controller has encountered a Firmwarebreakpoint.
897 MAJOR Internal Controller has encountered a Firmware breakpoint.
i960HwErrInternal Controller has encountered i960 processorspecific error.
912 MAJOR Internal Controller has encountered i960 processor specificerror.
sarmHwErrInternal Controller has encountered Strong-ARMprocessor specific error.
928 MAJOR Internal Controller has encountered Strong-ARM processorspecific error
FASTTRAK-MIB (promisev1.mib)
表16:FASTTRAK-MIB トラップ(ENTERPRISE : enterprises.7933.2.12)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
trpUnknownUnknown - possibly new driver error code
1 INFORMATIONAL Unknown
trpEccErrorECC Error on Disk <name> LBA <lba>
2 CRITICAL ECC Error on Disk
trpDiskDownDisk Down <disk_name>
3 MAJOR Disk Set Down by Driver
trpDiskOfflineDisk Offline <disk_name>
4 MAJOR Disk %d of array %d set offline by driver. Description: %d
trpDiskPluginDisk Plugin <disk_name>
5 MINOR New Disk Plugged In
trpAryBadSectorArray <num> had BadSector at LBA <lba>
6 INFORMATIONAL Bad sector encountered
trpRebuildStartRebuild Started Array <array> disk <disk>
7 INFORMATIONAL Rebuild started
trpSyncStartSynchronization Started, Array <array>
8 INFORMATIONAL Synchronization Started
trpRetryDiskRetry Disk Task, disk <disk> lba <lba>
9 MINOR Retry Disk Task
trpArrayOfflineArray Offline <array>
10 MAJOR Array Offline
trpArrayCriticalArray Critical <array>
11 CRITICAL Array Critical
trpArrayRebuildCompleteRebuild Completed, Array <array>, disk <disk>
12 INFORMATIONAL Rebuild Completed
trpArraySyncCompleteSync Completed, array <array>
13 INFORMATIONAL Synchronization Completed
trpMediaErrorArray <array>, disk <disk> has Media Error at LBA<lba>, cmd=<cmd>, status=<status>
14 CRITICAL Media Error on Disk
次の表は、FASTTRAK-MIBのトラップを掲載して、概要を示したものです。Promise IDE RAID Adapterからのトラップです。詳細についてはFastCheckMonitorを参照してください。
trpReserveSectorErrorReserved Sector Error, Disk <disk> lba <lba>
15 MINOR Reserved Sector Error
trpRebuildAbortedRebuild Aborted, Array <array>, disk <disk>,percent <percent>
16 CRITICAL Rebuild Aborted
trpSyncAbortedSynchronization Aborted, array <array>, percent<percent>
17 CRITICAL Sync. Aborted
trpECCFixFailECC Fix Failed
18 CRITICAL ECC Fix Failed
trpSyncCompErrorSync Compare Error, Array <array>, LBA= <lba>
19 MINOR Sync. Compare Error
trpSwapBoxPowerDownSwap Box Power Down, channel <ch>, msl <msl>
20 INFORMATIONAL Swap Box Power Down
trpSwapBoxPowerUpSwap Box Power Up, channel <ch>, msl <msl>
21 INFORMATIONAL Swap Box Power Up
trpSwapBoxBadSwapSwap Box, Bad Swap, channel <ch>, msl <msl>
22 MINOR Swap Box, Bad Swap
trpSwapBoxOverTempSwap Box, Over Temp, channel <ch>, msl <msl>,Temp <fahr>, C <cent>
23 MINOR Swap Box Over Temp
trpSwapBoxFanStoppedSwap Box Fan Stop, channel <ch>, msl <msl>,RPM= <rpm>
24 MINOR Swap Box Fan Stop
trpSwapBox12VOutOfRangeSwap Box, 12V Out of Range, channel <ch>, msl<msl>, 12V=<volts>
25 MINOR 12V Out of Range
trpSwapBox5VOutOfRangeSwap Box, 5V Out of Range, channel <ch>, msl<msl>, 5V=<volts>
26 MINOR 5V Out of Range
PROMISE-UNIFIED-MIB (promiseraid.mib)
表17:PROMISE-UNIFIED-MIB トラップ(ENTERPRISE : enterprises.7933.2.12)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
trpDiskOfflineDisk offline
1 CRITICAL Disk Offline: %s
trpDiskPluginNew disk plugged in
2 INFORMATIONAL New Disk Plugged In: %s
trpDiskMediaErrorMedia error on disk
3 MAJOR Disk Media Error: %s
trpDiskSMARTFailSMART error on disk
4 MAJOR Disk SMART Fail: %s
trpDiskAccessRetryDisk retry
5 INFORMATIONAL Retry Disk Access: %s
trpDiskECCErrorDisk ECC Error
6 MAJOR ECC Error on Disk: %s
trpDiskTimeOutDisk timed out
7 MAJOR Disk Time Out: %s
trpDiskBadSectorBad sector on array
8 CRITICAL Bad sector encountered on array:%s
trpArrayMediaErrorArray Media Error
9 CRITICAL Array has a read/write error: %s
trpArrayOfflineArray offline
10 CRITICAL Array offline: %s
trpArrayCriticalArray critical
11 MAJOR Array critical: %s
trpArrayCreateArray creation
12 INFORMATIONAL Create array: %s
trpArrayDeleteArray deletion
13 MAJOR Delete array: %s
trpArrayRebuildStartRebuild started
14 INFORMATIONAL Rebuild started on array: %s
trpArrayAutoRebuildStartAutomatic rebuild started
15 INFORMATIONAL Automatic Rebuild started on array: %s
trpArrayRebuildAbortedRebuild aborted on array
16 MAJOR Rebuild aborted on array: %s
trpArrayRebuildPausedRebuild paused on array
17 MAJOR Rebuild paused on array: %s
trpArrayRebuildResumedRebuild resumed on array
18 INFORMATIONAL Rebuild resumed on array: %s
trpArrayRebuildCompletedRebuild successfully completed
19 INFORMATIONAL Rebuild completed on array: %s
trpArrayRebuildFailedRebuild failed
20 INFORMATIONAL Rebuild failed on array: %s
trpArraySyncStartedSynchronization started on array
21 INFORMATIONAL Synchronization started on array: %s
trpArraySyncAbortedSynchronization aborted on array
22 INFORMATIONAL Synchronization aborted on array: %s
trpArraySyncPausedSynchronization paused on array
23 INFORMATIONAL Synchronization paused on array: %s
trpArraySyncResumedSynchronization resumed on array
24 INFORMATIONAL Synchronization resumed on array: %s
trpArraySyncCompletedSynchronization successfully completed on array
25 INFORMATIONAL Synchronization completed on array: %s
trpArraySyncFailedSynchronization failed on array
26 CRITICAL Synchronization failed on array: %s
trpSyncComparisonErrorSynchronization comparison error on array
27 CRITICAL Synchronization comparison error on array: %s
trpSwapBoxOverTempTemperature is too high for enclosure
28 MAJOR Swap Box Over Temp on enclosure: %s
trpSwapBoxFanStopFan stopped for enclosure
29 MAJOR Swap Box Fan Stop: %s
trpSwapBox5VOutOfRange5V over/under threshold for enclosure
30 MAJOR 5V Out of Range for array: %s
trpSwapBox12VOutOfRange12V over/under threshold for enclosure
31 MAJOR 12V Out of Range for array: %s
trpSwapBoxPowerUpEnclosure power on
32 INFORMATIONAL Swap Box Power On: %s
次の表は、PROMISE-UNIFIED-MIBのトラップを掲載して、概要を示したものです。Promise FastTrak SATA RAID Adapterからのトラップです。詳細についてはPromise Array Management (PAM)を参照してください。
trpSwapBoxPowerDownEnclosure power off
33 INFORMATIONAL Swap Box Power Off: %s
trpUnknownUnknown - possibly new driver error code
34 INFORMATIONAL Unknown
trpBatteryTempOutOfRangeBattery Temperature Out of Range
35 MAJOR The battery's temperature is out of range
trpBatteryUnstableTempBattery Temperature Unstable
36 MAJOR The battery's temperature is unstable
trpBatteryVoltOfRangeBattery Voltage Out of Range
37 MAJOR The battery's voltage is out of range
trpBatteryUnstableVoltBattery Voltage Unstable
38 MAJOR The battery's voltage is unstable
trpBatteryCommErrorBattery Communication Error
39 MAJOR There is a communication error in the battery
trpBatteryBecomeNormalBattery Communication Error
40 INFORMATIONAL The battery status becomes normal
trpWriteModeChangeWrite Mode Change/Toggle
41 INFORMATIONAL Write Mode state changed
trpDiskErrorFixDisk error fixed
42 INFORMATIONAL Disk error fixed by entity
trpMediaPatrolStartMedia Patrol
43 INFORMATIONAL Media patrol started
trpMediaPatrolStopMedia Patrol
44 INFORMATIONAL Media patrol stopped
trpMediaPatrolAbortMedia Patrol
45 CRITICAL Media patrol aborted
trpMediaPatrolCompleteMedia Patrol
46 INFORMATIONAL Media patrol completed
trpMediaPatrolPauseMedia Patrol
47 INFORMATIONAL Media patrol paused
trpMediaPatrolResumeMedia Patrol
48 INFORMATIONAL Media patrol resumed
UPSMAN (Upsman.mib)
表18:UPSMAN トラップ(ENTERPRISE : enterprises.1356)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
communicationLostUPS: Communication failure
1 CRITICAL Communication with the UPS has been lost. エージェントとUPS間の通信が異常。
upsOverloadUPS: UPS overload
2 CRITICALThe UPS has sensed a load greater than 100 percent of itsrated capacity.
UPSの出力過負荷状態。
upsTurnedOffUPS: Switching off
3 MAJOR The UPS is being switched off by a management station. UPSの出力停止。
communicationEstablishedUPS: Communication established
4 INFORMATIONAL Communication with the UPS has been established.エージェントとUPS間の通信異常からの回復。
powerRestoredUPS: power restored
5 INFORMATIONAL Normal power has been restored to the UPS.UPSへの入力電圧が仕様範囲外から復帰した。
upsOnBatteryUPS: On battery
6 MAJOR The UPS system has switched to battery backup power.
UPSは、バックアップ運転中。このトラップは、UPSが停止するか、又は、バックアップ運転が解除されるまで1分間隔で送信される。
testStartedUPS: Test started
7 INFORMATIONAL UPS test has been started.UPSテスト開始を通知する。
testCompletedUPS: Test completed
8 INFORMATIONAL UPS test has been completed.UPSテスト完了を通知する。
upsBatteryLowUPS: Battery Low
9 MAJOR UPS Battery Low.バッテリ容量の低下upsBatteryStatus参照。繰返し値は、upsConfigIntervalTrapTimeによる。
upsShutdownImminentUPS: Shutdown Imminent
10 INFORMATIONAL UPS Shutdown Imminent. サーバシャットダウンの1分前を通知する。
upsmanStartedUPS: UpsMan service started
11 INFORMATIONAL UpsMan service started. サービスの開始。
upsmanTrapInputBadUPS: Abnormal input condition
12 MAJOR Abnormal input condition UPSへの入力電圧が仕様範囲外である。
upsmanTrapOutputOverloadRemovedUPS: Overload Removed
13 INFORMATIONAL Overload Removed UPSの出力の過負荷状態からの回復。
upsmanTrapBatteryBadUPS: Bad battery
14 MAJOR Bad battery バッテリの交換が必要。
upsmanTrapTempBadUPS: Bad temperature
15 MAJOR Bad temperature
温度が仕様範囲外。温度異常の発生場所は、特定しなくてもよい。温度異常内容の詳細情報はupsAlarmTempBadDetailを参照することによって得られる。
upsmanTrapTempBadRemovedUPS: Bad temperatureRemove
16 INFORMATIONAL Bad temperatureRemove 温度の仕様範囲外からの回復。
upsmanTrapFatalFaultUPS: Fatal fault
17 CRITICAL Fatal faultUPSに重故障発生UPSにバックアップ運転が不可能となる重故障が発生した時に通知する。
UPS-MIB (RFC1628.mib)
表19:UPS-MIB トラップ(ENTERPRISE : mib2.33.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
upsTrapOnBatteryUPS on Battery
1 CRITICAL The UPS is on battery power since %d seconds
upsTrapTestCompletedUPS Test Completed
2 INFORMATIONAL This trap is sent upon completion of a UPS diagnostic test.
upsTrapAlarmEntryAddedUPS Alarm Entry Added
3 INFORMATIONALThis trap is sent each time an alarm is inserted into to thealarm table. It is sent on the insertion of all alarms except forupsAlarmOnBattery and upsAlarmTestInProgress.
upsTrapAlarmEntryRemovedUPS Alarm Entry Removed
4 INFORMATIONALThis trap is sent each time an alarm is removed from thealarm table. It is sent on the removal of all alarms except forupsAlarmTestInProgress.
次の表は、UPS-MIBのトラップを掲載して、概要を示したものです。NetpowerView Fからのトラップです。詳細についてはNetpowerView F説明書を参照してください。
次の表は、UPSMANのトラップを掲載して、概要を示したものです。NetpowerView Fからのトラップです。詳細についてはNetpowerView F説明書を参照してください。
PowerNet-MIB (powernet.mib)
表20:PowerNet-MIB トラップ(ENTERPRISE : enterprises.318)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
communicationLostAPC UPS: Communication failure
1 CRITICAL Communication lost between the agent and the UPS.
upsOverloadAPC UPS: UPS overload
2 CRITICALThe UPS has sensed a load greater than 100 percent of itsrated capacity.
upsDiagnosticsFailedAPC UPS: Failed self-test
3 CRITICAL The UPS has failed its internal self-test.
upsDischargedAPC UPS: batteries are discharged
4 CRITICAL The UPS batteries are discharged.
upsOnBatteryAPC UPS: On battery
5 MAJOR The UPS is now providing battery backup power.
smartBoostOnAPC UPS: SmartBoost
6 MINOR The UPS has enabled SmartBoost.
lowBatteryAPC UPS: Low battery
7 CRITICALThe UPS system's batteries are low and will soon beexhausted.
communicationEstablishedAPC UPS: Communication established
8 INFORMATIONAL Communication established between the agent and the UPS.
powerRestoredAPC UPS: Utility restored
9 INFORMATIONAL Normal power has been restored to the UPS.
upsDiagnosticsPassedAPC UPS: Passed self-test
10 INFORMATIONAL The UPS has passed its internal self-test.
returnFromLowBatteryAPC UPS: Battery normal
11 INFORMATIONAL The UPS has returned from a low battery condition.
upsTurnedOffAPC UPS: Switching off
12 MAJOR The UPS is being switched off by a management station.
upsSleepingAPC UPS: Going to sleep
13 MAJOR The UPS is going into sleep mode.
upsWokeUpAPC UPS: Wake up
14 INFORMATIONAL The UPS has returned from sleep mode.
upsRebootStartedAPC UPS: Starting reboot
15 MAJOR The UPS has started its reboot sequence.
upsDipSwitchChangedAPC UPS: DIP switch altered
16 MINOR The DIP switch settings on the UPS have been changed.
upsBatteryNeedsReplacementAPC UPS: UPS batteries needs replacement
17 CRITICAL The UPS batteries require immediate replacement.
contactFaultAPC M-UPS: Contact fault
18 CRITICAL A Measure-UPS contact closure has faulted.
contactFaultResolvedAPC M-UPS: Contact normal
19 INFORMATIONALA Measure-UPS contact closure has returned to it's defaultstate.
hardwareFailureBypassAPC UPS: On bypass due to internal fault
20 CRITICAL The UPS is on bypass due to an internal fault.
softwareBypassAPC UPS: On bypass by user via software or panel
21 MINOR UPS put on bypass by user via software or front UPS panel.
switchedBypassAPC UPS: On bypass initiated by user
22 MINOR UPS put on bypass by user.
returnFromBypassAPC UPS: UPS has returned from bypass
23 INFORMATIONAL The UPS has returned from bypass mode.
bypassPowerSupplyFailureAPC UPS: Base module bypass power supplyneeds repair
24 CRITICAL The base module bypass power supply needs repair.
baseFanFailureAPC UPS: Base module fan needs repair
25 CRITICAL The base module fan needs repair.
batteryPackCommLostAPC UPS: Communication lost with battery packs
26 MINORCommunication lost with external battery packs, checkbattery signal cable.
batteryPackCommEstablishedAPC UPS: Communication established with batterypacks
27 INFORMATIONAL Communication established with external battery packs.
calibrationStartAPC UPS: Calibration initiated
28 INFORMATIONAL A battery run time calibration test has been initiated.
restartAgentAPC SNMP Agent: Agent restarting
29 INFORMATIONAL Agent restarting as commanded by manager.
upsTurnedOnAPC UPS: A UPS is turned on.
30 INFORMATIONAL A UPS is turned on.
smartAvrReducingAPC UPS: Smart-AVR reducing
31 MINOR The UPS has enabled Smart-AVR voltage reduction.
codeAuthenticationDoneAPC CODE: Authentication on agent code image isdone.
32 INFORMATIONAL Authentication on agent code image is done.
upsOverloadClearedAPC UPS: Overload cleared.
33 MINOR The overload condition has been cleared. .
smartBoostOffAPC UPS: Smartboost off.
34 MINOR The UPS has returned from smartboost.
smartAvrReducingOffAPC UPS: Smart-AVR reducing off
35 MINOR The UPS has returned from Smart-AVR voltage reduction.
upsBatteryReplacedAPC UPS: Bad battery replaced
36 MINOR The UPS has returned from a bad battery fault.
calibrationEndAPC UPS: Calibration end
37 MINOR The UPS has finished calibrating
dischargeClearedAPC UPS: Discharge cleared.
38 MINOR The UPS discharge condition has been cleared.
gracefullShutdownAPC UPS: A gracefull shutdown has been initiated.
39 MINOR A gracefull shutdown has been initiated.
outletOnAPC PDU: State change.
41 WARNING An OUTLET has been turned on
outletOffAPC PDU: State change.
42 WARNING An OUTLET has turned off.
outletRebootAPC PDU: State change.
43 WARNING An OUTLET has rebooted.
configChangeSNMPAPC: State change.
44 WARNING The SNMP configuration has been changed.
configChangeOutletAPC PDU: State change.
45 WARNING An outlet configuration has been changed.
accessViolationConsoleAPC: Access violation.
46 WARNING Three unsuccessful logins have been attempted.
次の表は、PowerNet-MIBのトラップを掲載して、概要を示したものです。APC社製UPS Webカードからのトラップです。詳細についてはAPC社製UPS説明書を参照してください。
accessViolationHTTPAPC: Access violation.
47 WARNING An unsuccessful attempt to login via HTTP.
passwordChangeAPC: Password change.
48 WARNING Someone has changed the password on the PDU.
badVoltageAPC UPS: Bad output voltage.
49 WARNING The output voltage is not within acceptable range.
badVoltageClearedAPC UPS: The bad voltage output condition hasbeen cleared.
50 INFORMATIONAL The output voltage has returned to an acceptable level.
chargerFailureAPC UPS: The battery charger has failed.
51 WARNING The battery charger has failed.
chargerFailureClearedAPC UPS: The battery charger failure conditionhas been cleared.
52 INFORMATIONAL The battery charger failure condition has been cleared.
batteryOverTemperatureAPC UPS: The battery temperature threshold hasbeen violated.
53 WARNING The battery temperature threshold has been violated.
batteryOverTemperatureClearedAPC UPS: The battery over temperature has beencleared.
54 INFORMATIONAL The battery over temperature has been cleared.
smartRelayFaultAPC UPS: SmartBoost(TM) or SmartTrim(TM)relay fault.
55 WARNING SmartBoost(TM) or SmartTrim(TM) relay fault.
smartRelayFaultClearedAPC UPS: SmartBoost(TM) or SmartTrim(TM)relay fault has been cleared.
56 INFORMATIONALSmartBoost(TM) or SmartTrim(TM) relay fault has beencleared.
humidityThresholdViolation1APC UPS: Probe 1 humidity threshold violated.
57 WARNING Probe 1 humidity threshold violated.
humidityThresholdViolationCleared1APC MEASURE-UPS: A humidity thresholdviolation has been cleared on probe 1.
58 INFORMATIONAL A humidity threshold violation has been cleared on probe 1.
temperatureThresholdViolation1APC MEASURE-UPS: A temperature threshold hasbeen violated on probe 1.
59 CRITICAL A temperature threshold has been violated on probe 1.
temperatureThresholdViolationCleared1APC MEASURE-UPS: A temperature thresholdviolation has been cleared on probe 1.
60 MINORA temperature threshold violation has been cleared on probe1.
humidityThresholdViolation2APC MEASURE-UPS: A humidity threshold hasbeen violated on probe 2.
61 CRITICAL A humidity threshold has been violated on probe 2.
humidityThresholdViolationCleared2APC MEASURE-UPS: A humiditythreshold violationhas been cleared on probe 2.
62 INFORMATIONAL A humidity threshold violation has been cleared on probe 2.
temperatureThresholdViolation2APC MEASURE-UPS: A temperature threshold hasbeen violated on probe 2.
63 CRITICAL A temperature threshold has been violated on probe 2.
temperatureThresholdViolationCleared2APC MEASURE-UPS: A temperature thresholdviolation has been cleared on probe 2.
64 INFORMATIONALA tempreature threshold violation has been cleared on probe2.
mupsCommunicationEstablishedAPC MUPS: Communication established with theMeasure-UPS
65 INFORMATIONAL Communication established between the agent and the MUPS.
mupsCommunicationLostAPC MUPS: MUPS Communication failure
66 CRITICAL Communication lost between the agent and the MUPS.
batteryIncreaseAPC UPS: The number of batteries has increased.
67 INFORMATIONAL The number of batteries has increased.
batteryDecreaseAPC UPS: The number of batteries has decreased.
68 INFORMATIONAL The number of batteries has decreased.
powerModuleIncreaseAPC UPS: The number of power modules hasincreased.
69 INFORMATIONAL The number of power modules has increased.
powerModuleDecreaseAPC UPS: The number of power modules hasdecreased.
70 INFORMATIONAL The number of power modules has decreased.
intelligenceModuleInsertedAPC UPS: An intelligence module has been
71 INFORMATIONAL An intelligence module has been inserted.
intelligenceModuleRemovedAPC UPS: An intelligence module has been
72 INFORMATIONAL An intelligence module has been removed.
rintelligenceModuleInsertedAPC UPS: A redundant intelligence module hasbeen inserted.
73 INFORMATIONAL A redundant intelligence module has been inserted.
rintelligenceModuleRemovedAPC UPS: An redundant intelligence module hasbeen removed.
74 INFORMATIONAL An redundant intelligence module has been removed.
extBatteryFrameInceaseAPC UPS: An external battery frame has been
75 INFORMATIONAL An external battery frame has been added.
extBatteryFrameDecreaseAPC UPS: An external battery frame has beenremoved.
76 INFORMATIONAL An external battery frame has been removed.
abnormalConditionAPC UPS: An abnormal condition has been
77 MAJOR An abnormal condition has been detected.
abnormalConditionClearedAPC UPS: An abnormal condition has been cleared.
78 INFORMATIONAL An abnormal condition has been cleared.
deviceStatusChangeAPC : The status of the device being monitoredhas changed.
79 INFORMATIONAL The status of the device being monitored has changed.
noBatteriesAPC UPS: No batteries attached.
80 WARNING The UPS has no batteries attached.
noBatteriesClearedAPC UPS: The no batteries attached condition hasbeen cleared.
81 INFORMATIONAL The UPS's batteries have been attached.
userAddedAPC: A new user has been added.
82 INFORMATIONAL A new user has been added.
userDeletedAPC: A user has been deleted.
83 INFORMATIONAL A user has been deleted.
userModifiedAPC: A user has been modified.
84 INFORMATIONAL A user has been modified.
msvmCommunicationEstablishedAPC: Communications with the MasterSwitch VMhas been established.
85 INFORMATIONALCommunications with the MasterSwitch VM has beenestablished.
msvmCommunicationLostAPC: Communications with the MasterSwitch VMhas been lost.
86 INFORMATIONAL Communications with the MasterSwitch VM has been lost.
msvmOverloadAPC: The MasterSwitch VM is near or at anoverload condition.
87 INFORMATIONAL The MasterSwitchVM is near or at an overload condition.
msvmOverloadClearedAPC: The overload condition on the MasterSwitchVM has been cleared.
88 INFORMATIONALThe overload condition on the MasterSwitch VM has beencleared.
msvmOutletOnAPC: An outlet on the MasterSwitch VM has
89 INFORMATIONAL An outlet on the MasterSwitch VM has turned on.
msvmOutletOffAPC: An outlet on the MasterSwitch VM hasturned off.
90 INFORMATIONAL An outlet on the MasterSwitch VM has turned off.
msvmDeviceConfigChangeAPC: A device configuration change has been madeon a MasterSwitch VM.
91 INFORMATIONALA device configuration change has been made on aMasterSwitch VM.
msvmOutletConfigChangeAPC: An outlet configuration change has beenmade on a MasterSwitch VM.
92 INFORMATIONALAn outlet configuration change has been made on aMasterSwitch VM.
msvmLowLoadAPC: The MasterSwitch VM has violated the lowload threshold.
93 INFORMATIONAL The MasterSwitch VM has violated the low load threshold.
msvmLowLoadClearedAPC: The low load condition on the MasterSwitchVM has been cleared.
94 INFORMATIONALThe low load condition on the MasterSwitch VM has beencleared.
msvmNearOverloadAPC: The MasterSwitch VM is near or at anoverload condition.
95 INFORMATIONAL The MasterSwitchVM is near or at an overload condition.
msvmNearOverloadClearedAPC: The overload condition on the MasterSwitchVM has been cleared.
96 INFORMATIONALThe overload condition on the MasterSwitch VM has beencleared.
msvmPowerSupplyStatusChangeAPC: The power supply status of the MasterSwitchVM has changed.
97 INFORMATIONALThe power supply status of the MasterSwitch VM haschanged.
mspCommunicationEstablishedAPC: Communications with the MasterSwitch plushas been established.
98 INFORMATIONALCommunications with the MasterSwitch plus has beenestablished.
mspCommunicationLostAPC: Communications with the MasterSwitch plushas been lost.
99 INFORMATIONAL Communications with the MasterSwitch plus has been lost.
mspOutletOnAPC: An outlet on the MasterSwitch plus hasturned on.
100 INFORMATIONAL An outlet on the MasterSwitch plus has turned on.
mspOutletOffAPC: An outlet on the MasterSwitch plus hasturned off.
101 INFORMATIONAL An outlet on the MasterSwitch plus has turned off.
mspDeviceConfigChangeAPC: A device configuration change has been madeon a MasterSwitch plus.
102 INFORMATIONALA device configuration change has been made on aMasterSwitch plus.
mspOutletConfigChangeAPC: An outlet configuration change has beenmade on a MasterSwitch plus.
103 INFORMATIONALAn outlet configuration change has been made on aMasterSwitch plus.
rsSourceSwitchedAPC Redundant Switch: The Redundant Switch hasswitched source.
104 INFORMATIONAL The Redundant Switch has switched source.
rsLostRedundancyAPC Redundant Switch: The Redundant Switch haslost redundancy.
105 MAJOR The Redundant Switch has has lost redundancy.
rsRedundancyRestoredAPC Redundant Switch: Redundancy has beenrestored to the Redundant Switch .
106 INFORMATIONAL Redundancy has been restored to the Redundant Switch .
rsConfigChangeAPC: A configuration change has been made on aRedundant Switch.
107 INFORMATIONALA configuration change has been made on a RedundantSwitch.
rsCommunicationEstablishedAPC: Communications with the Redundant Switchhas been established.
108 INFORMATIONALCommunications with the Redundant Switch has beenestablished.
rsCommunicationLostAPC: Communications with the Redundant Switchhas been lost.
109 CRITICAL Communications with the Redundant Switch has been lost.
dcCommunicationEstablishedAPC: Communications with the DC power plant hasbeen established.
110 INFORMATIONALCommunications with the DC power plant has beenestablished.
dcCommunicationLostAPC: Communications with the DC power plant hasbeen lost.
111 CRITICAL Communications with the DC power plant has been lost.
dcActivePINChangedAPC: The active PIN on the DC controller has beenchanged.
112 INFORMATIONAL The active PIN on the DC controller has been changed.
dcMajorAlarmAPC: A Major alarm is active in the DC powerplant.
113 CRITICAL A Major alarm is active in the DC power plant.
dcMajorAlarmClearedAPC: A Major alarm is no longer active in the DCpower plant.
114 INFORMATIONAL A Major alarm is no longer active in the DC power plant.
dcMinorAlarmAPC: A Minor alarm is active in the DC powerplant.
115 INFORMATIONAL A Minor alarm is active in the DC power plant.
dcMinorAlarmClearedAPC: A Minor alarm is no longer active in the DCpower plant.
116 INFORMATIONAL A Minor alarm is no longer active in the DC power plant.
dcOutputRelayOnAPC: An output relay has gone on.
117 INFORMATIONAL An output relay has gone on in the DC power plant.
dcOutputRelayOffAPC: An output relay has gone off.
118 INFORMATIONAL An output relay has gone off in the DC power plant.
dcInputRelayOnAPC: An input relay has gone on.
119 INFORMATIONAL An input relay has gone on in the DC power plant.
dcInputRelayOffAPC: An input relay has gone off.
120 INFORMATIONAL An input relay has gone off in the DC power plant.
logicPowerSuppliesIncreasedAPC UPS: The number of system power supplieshas increased.
121 INFORMATIONAL The number of system power supplies has increased.
logicPowerSuppliesDecreasedAPC UPS: The number of system power supplieshas decreased.
122 INFORMATIONAL The number of system power supplies has decreased.
externalSwitchGearClosedAPC UPS: External Switch Gear closed.
123 INFORMATIONAL External Switch Gear closed.
externalSwitchGearOpenedAPC UPS: External Switch Gear opened.
124 INFORMATIONAL External Switch Gear opened.
generalDeviceEventAPC Device event
125 INFORMATIONAL APC Device event.
atsSourceSwitchedAPC Automatic Transfer Switch: The ATS hasswitched source
126 INFORMATIONAL The Automatic Transfer Switch has switched source.
atsLostRedundancyAPC Automatic Transfer Switch: The ATS has lostredundancy.
127 MAJOR The Automatic Transfer Switch has has lost redundancy.
atsRedundancyRestoredAPC Automatic Transfer Switch: Redundancy hasbeen restored.
128 INFORMATIONALRedundancy has been restored to the Automatic TransferSwitch .
atsConfigChangeAPC Automatic Transfer Switch: ATS configurationchanged.
129 INFORMATIONALA configuration change has been made on a AutomaticTransfer Switch.
atsCommunicationEstablishedAPC Automatic Transfer Switch: Communicationsestablished.
130 INFORMATIONALCommunications with the Automatic Transfer Switch hasbeen established.
atsCommunicationLostAPC Automatic Transfer Switch: Communications lost.
131 MAJORCommunications with the Automatic Transfer Switch hasbeen lost.
atsOverCurrentAPC Automatic Transfer Switch: Output Currentexceeded threshold
132 MAJOR Output Current has exceeded Threshold.
atsOverCurrentClearedAPC Automatic Transfer Switch: Output Currentbelow threshold.
133 INFORMATIONAL Output Current has returned below threshold.
atsPowerSupplyFailureAPC Automatic Transfer Switch: The ATS PowerSupply has failed.
134 MAJOR The Automatic Transfer Switch Power Supply has failed.
atsPowerSupplyFailureClearedAPC Automatic Transfer Switch: Power SupplyFailure Cleared.
135 INFORMATIONAL The Automatic Transfer Switch Power Supply Failure Cleared.
dcMainsFailAlarmAPC: A Mains Fail alarm is active in the DC powerplant.
136 WARNING A Mains Fail alarm is active in the DC power plant.
dcMainsFailAlarmClearedAPC: Mains Fail alarm is no longer active in the DCpower plant.
137 INFORMATIONAL Mains Fail alarm is no longer active in the DC power plant.
dcFanFailAlarmAPC: A Fan Fail alarm is active in the DC powerplant.
138 WARNING A Fan Fail alarm is active in the DC power plant.
dcFanFailAlarmClearedAPC: A Fan Fail alarm is no longer active in the DCpower plant.
139 INFORMATIONAL A Fan Fail alarm is no longer active in the DC power plant.
dcRectifierOvertempAlarmAPC: Rect. Overtemp alarm is active in the powerplant.
140 WARNING Rect. Overtemp alarm is active in the power plant.
dcRectifierOvertempAlarmClearedAPC: Rect. Overtmp alarm is no longer active inthe power plant.
141 INFORMATIONAL Rect. Overtmp alarm is no longer active in the power plant.
dcCurrentLimitAlarmAPC: A Current Limit alarm is active in the powerplant.
142 WARNING A Current Limit alarm is active in the power plant.
dcCurrentLimitAlarmClearedAPC: Current Limit alarm is no longer active in thepower plant.
143 INFORMATIONAL Current Limit alarm is no longer active in the power plant.
dcRectifierFailAlarmAPC: A Rect. Fail alarm is active in the powerplant.
144 WARNING A Rect. Fail alarm is active in the power plant.
dcRectifierFailAlarmClearedAPC: Rect. Fail alarm is no longer active in thepower plant.
145 INFORMATIONAL Rect. Fail alarm is no longer active in the power plant.
dcMultRectFailAlarmAPC: Multiple Rect. Fail alarm is active in thepower plant.
146 WARNING Multiple Rect. Fail alarm is active in the powerplant.
dcMultRectFailAlarmClearedAPC: Mult Rect Fail alarm is no longer active in thepowerplant.
147 INFORMATIONAL Mult Rect Fail alarm is no longer active in the powerplant.
dcBatteryBreakerAlarmAPC: Batt. Breaker alarm is active in the powerplant.
148 WARNING Batt. Breaker alarm is active in the power plant.
dcBatteryBreakerAlarmClearedAPC: Batt. Breaker alarm is no longer active in thepower plant.
149 INFORMATIONAL Batt. Breaker alarm is no longer active in the power plant.
dcRectifierOVPAlarmAPC: A Rect. OVP alarm is active in the powerplant.
150 WARNING A Rect. OVP alarm is active in the power plant.
dcRectifierOVPAlarmClearedAPC: A Rect. OVP alarm is no longer active in thepower plant.
151 INFORMATIONAL A Rect. OVP alarm is no longer active in the power plant.
dcLVDImminentAlarmAPC: A LVD Imminent alarm is active in the powerplant.
152 WARNING A LVD Imminent alarm is active in the powerplant.
dcLVDImminentAlarmClearedAPC: A LVD Imminent alarm is no longer active inthe power plant.
153 INFORMATIONAL A LVD Imminent alarm is no longer active in the powerplant.
dcFuseCBAlarmAPC: A Fuse/CB alarm alarm is active in the DCpower plant.
154 WARNING A Fuse/CB alarm is active in the DC power plant.
dcFuseCBAlarmClearedAPC: A Fuse/CB alarm is no longer active in theDC power plant.
155 INFORMATIONAL A Fuse/CB alarm is no longer active in the DC power plant.
dcBatteryTestFailAPC: A Battery Test failed in the DC power plant.
156 WARNING A Battery Test failed in the DC power plant.
dcTemperatureAlarmAPC: A Temperature alarm is active in the powerplant.
157 WARNING A Temperature alarm is active in the power plant.
dcTemperatureAlarmClearedAPC: A Temperature alarm is no longer active inthe power plant.
158 INFORMATIONAL A Temperature alarm is no longer active in the power plant.
dcHumidityAlarmAPC: A Humidity alarm is active in the DC powerplant.
159 WARNING A Humidity alarm is active in the DC power plant.
dcHumidityAlarmClearedAPC: A Humidity alarm is no longer active in theDC power plant.
160 INFORMATIONAL A Humidity alarm is no longer active in the DC power plant.
dcBBCommunicationEstablishedAPC: Power plant bridging board communicationsestablished.
161 INFORMATIONAL Power plant bridging board communications established.
dcBBCommunicationLostAPC: Power plant bridging board communicationslost.
162 MAJOR Power plant bridging board communications lost.
iemHighTempThresholdViolationAPC IEM: High temperature threshold violation.
163 MAJOR High temperature threshold violation.
iemHighTempThresholdViolationClearedAPC IEM: High temperature threshold violation
164 INFORMATIONAL High temperature threshold violation has been cleared.
iemLowTempThresholdViolationAPC IEM: Low temperature threshold violation.
165 MAJOR Low temperature threshold violation.
iemLowTempThresholdViolationClearedAPC IEM: Low temperature threshold violation
166 INFORMATIONAL Low temperature threshold violation has been cleared.
iemHighHumidThresholdViolationAPC IEM: High humidity threshold violation.
167 MAJOR High humidity threshold violation.
iemHighHumidThresholdViolationClearedAPC IEM: High humidity threshold violation cleared.
168 INFORMATIONAL High humidity threshold violation has been cleared.
iemLowHumidThresholdViolationAPC IEM: Low humidity threshold violation.
169 MAJOR Low humidity threshold violation.
iemLowHumidThresholdViolationClearedAPC IEM: Low humidity threshold violation cleared.
170 INFORMATIONAL Low humidity threshold violation has been cleared.
iemProbeDisconnectedAPC IEM: Probe disconnected.
171 WARNING Probe has been disconnected.
iemProbeConnectedAPC IEM: Probe Connected.
172 INFORMATIONAL Probe has been connected.
iemContactFaultAPC IEM: Contact fault.
173 MAJOR Contact fault.
iemContactFaultClearedAPC IEM: Contact fault.
174 INFORMATIONAL Contact fault cleared.
iemRelayFaultAPC IEM: Output relay fault.
175 MAJOR Output relay has faulted.
iemRelayFaultClearedAPC IEM: Output relay fault condition cleared.
176 INFORMATIONAL Output relay fault cleared.
bmBatManCommEstabBatMan : Communications Established.
177 INFORMATIONAL Communications Established.
bmBatManCommLostBatMan : Communications Lost.
178 MAJOR Communications Lost.
bmBatManKneeAlarmBatMan : Knee Alarm Detected.
179 MAJOR Knee Alarm Detected.
bmBatManKneeAlarmClearedBatMan : Knee Alarm Cleared.
180 INFORMATIONAL Knee Alarm Cleared.
bmBatManChargerAlarmBatMan : Charger Alarm Detected.
181 WARNING Charger Alarm Detected.
bmBatManChargerAlarmClearedBatMan : Charger Alarm Cleared.
182 INFORMATIONAL Charger Alarm Cleared.
bmBatManBatteryAlarmBatMan : Battery Alarm Detected.
183 WARNING Battery Alarm Detected.
bmBatManBatteryAlarmClearedBatMan : Battery Alarm Cleared.
184 INFORMATIONAL Battery Alarm Cleared.
bmBatManEnvironmentAlarmBatMan : Environment Alarm Detected.
185 WARNING Environment Alarm Detected.
bmBatManEnvironmentAlarmClearedBatMan : Environment Alarm Cleared.
186 INFORMATIONAL Environment Alarm Cleared.
bmBatManMaintenanceAlarmBatMan : Maintenance Due Alarm Detected.
187 INFORMATIONAL Maintenance Due Alarm Detected.
bmBatManMaintenanceAlarmClearedBatMan : Maintenance Due Alarm Cleared.
188 INFORMATIONAL Maintenance Due Alarm Cleared.
pduCommunicationEstablishedAPC PDU: Communication Established.
189 INFORMATIONAL Communication Established.
pduCommunicationLostAPC PDU: Communication Lost.
190 MAJOR Communication Lost.
pduUtilityLineUndervoltageAPC PDU: Utility Line Undervoltage.
191 MAJOR Utility Line Undervoltage.
pduUtilityLineUndervoltageClearedAPC PDU: Utility Line Undervoltage Cleared.
192 INFORMATIONAL Utility Line Undervoltage Cleared.
pduUtilityLineOvervoltageAPC PDU: Utility Line Overvoltage.
193 MAJOR Utility Line Overvoltage.
pduUtilityLineOvervoltageClearedAPC PDU: Utility Line Overvoltage Cleared.
194 INFORMATIONAL Utility Line Overvoltage Cleared.
pduGroundOvercurrentAPC PDU: Ground Overcurrent.
195 MAJOR Ground Overcurrent.
pduGroundOvercurrentClearedAPC PDU: Ground Overcurrent Cleared.
196 INFORMATIONAL Ground Overcurrent Cleared.
pduCircuitPanelInputUndervoltageAPC PDU: Circuit Panel Input Undervoltage.
197 MAJOR Circuit Panel Input Undervoltage.
pduCircuitPanelInputUndervoltageClearedAPC PDU: Circuit Panel Input Undervoltage
198 INFORMATIONAL Circuit Panel Input Undervoltage Cleared.
pduCircuitPanelInputOvervoltageAPC PDU: Circuit Panel Input Overvoltage.
199 MAJOR Circuit Panel Input Overvoltage.
pduCircuitPanelInputOvervoltageClearedAPC PDU: Circuit Panel Input Overvoltage Cleared.
200 INFORMATIONAL Circuit Panel Input Overvoltage Cleared.
pduCircuitPanelInputUndercurrentAPC PDU: Circuit Panel Input Undercurrent.
201 MAJOR Circuit Panel Input Undercurrent.
pduCircuitPanelInputUndercurrentClearedAPC PDU: Circuit Panel Input Undercurrent
202 INFORMATIONAL Circuit Panel Input Undercurrent Cleared.
pduCircuitPanelInputOvercurrentAPC PDU: Circuit Panel Input Overcurrent.
203 MAJOR Circuit Panel Input Overcurrent.
pduCircuitPanelInputOvercurrentClearedAPC PDU: Circuit Panel Input Overcurrent Cleared.
204 INFORMATIONAL Circuit Panel Input Overcurrent Cleared.
pduCircuitPanelFrequencyOutOfRangeAPC PDU: Circuit Panel Input Frequency Out OfRange.
205 MAJOR Circuit Panel Input Frequency Out Of Range.
pduCircuitPanelFrequencyOutofRangeClearedAPC PDU: Circuit Panel Input Frequency NoLonger Out Of Range.
206 INFORMATIONAL Circuit Panel Input Frequency No Longer Out Of Range.
pduCircuitPanelNeutralOvercurrentAPC PDU: Circuit Panel Input Neutral Overcurrent.
207 MAJOR Circuit Panel Input Neutral Overcurrent.
pduCircuitPanelNeutralOvercurrentClearedAPC PDU: Circuit Panel Input Neutral OvercurrentCleared.
208 INFORMATIONAL Circuit Panel Input Neutral Overcurrent Cleared.
pduSystemOffAPC PDU: System Off.
209 MAJOR PDU System Off.
pduOnBatteryModeAPC PDU: On Battery Mode.
210 MAJOR PDU is in On Battery Mode.
pduMaintenanceBypassModeAPC PDU: Maintenance Bypass Mode.
211 INFORMATIONAL PDU is in Maintenance Bypass Mode.
pduAtypicalBypassModeAPC PDU: Atypical Bypass Mode.
212 WARNING PDU is in Atypical Bypass Mode.
pduNoPanelFeedModeAPC PDU: No Panel Feed Mode.
213 MAJOR PDU is in No Panel Feed Mode.
pduUpsOperationModeAPC PDU: Ups Operation Mode.
214 INFORMATIONAL PDU is in Ups Operation Mode.
pduForcedBypassModeAPC PDU: Forced Bypass Mode.
215 WARNING PDU is in Forced Bypass Mode.
pduInputTransformerOverTemperatureAPC PDU: Input Transformer Over Temperature.
216 MAJOR Input Transformer Over Temperature.
pduInputTransformerOverTemperatureClearedAPC PDU: Input Transformer Over TemperatureCleared.
217 INFORMATIONAL Input Transformer Over Temperature Cleared.
pduUPSInputVoltageLostAPC PDU: UPS Input Voltage phase-N Lost.
218 MAJOR UPS Input Voltage phase-N Lost.
pduUPSInputVoltageRestoredAPC PDU: UPS Input Voltage phase-N Restored.
219 INFORMATIONAL UPS Input Voltage phase-N Restored.
pduContactFaultAPC PDU: Contact Abnormal.
220 MAJOR Contact Abnormal.
pduContactFaultClearedAPC PDU: Contact Normal.
221 INFORMATIONAL Contact Normal.
rmPDUUndercurrentAPC RM PDU: Undercurrent.
222 MAJOR Undercurrent.
rmPDUUndercurrentClearedAPC RM PDU: Undercurrent Cleared.
223 INFORMATIONAL Undercurrent Cleared.
rmPDUOvercurrentAPC RM PDU: Overcurrent.
224 MAJOR Overcurrent.
rmPDUOvercurrentClearedAPC RM PDU: Overcurrent Cleared.
225 INFORMATIONAL Overcurrent Cleared.
rmPDUOverloadAPC RM PDU: Overload.
226 MAJOR Overload.
rmPDUOverloadClearedAPC RM PDU: Overload Cleared.
227 INFORMATIONAL Overload Cleared.
rmPDUCommunicationEstablishedAPC RM PDU: Communication Established.
228 INFORMATIONAL Communication Established.
rmPDUCommunicationLostAPC RM PDU: Communication Lost.
229 MAJOR Communication Lost.
emsCommunicationEstablishedAPC EMS: Communication Established.
230 INFORMATIONAL Communication Established.
emsCommunicationLostAPC EMS: Communication Lost.
231 MAJOR Communication Lost.
emsProbeConnectedAPC EMS: Probe Connected.
232 INFORMATIONAL Probe Connected.
emsProbeDisconnectedAPC EMS: Probe Disconnected.
233 MAJOR Probe Disconnected.
emsSensorConnectedAPC EMS: Sensor Connected.
234 INFORMATIONAL Sensor Connected.
emsSensorDisconnectedAPC EMS: Sensor Disconnected.
235 MAJOR Sensor Disconnected.
emsSensorFaultAPC EMS: Sensor Fault.
236 MAJOR Sensor Fault.
emsSensorFaultClearedAPC EMS: Sensor Fault Cleared.
237 INFORMATIONAL Sensor Fault Cleared.
emsBeaconConnectedAPC EMS: Beacon Connected.
238 INFORMATIONAL Beacon Connected.
emsBeaconDisconnectedAPC EMS: Beacon Disconnected.
239 MAJOR Beacon Disconnected.
emsBeaconOnAPC EMS: Beacon On.
240 INFORMATIONAL Beacon On.
emsBeaconOffAPC EMS: Beacon Off.
241 INFORMATIONAL Beacon Off.
emsMajorAlarmAPC EMS: Major Alarm.
242 MAJOR Major Alarm.
emsMajorAlarmClearedAPC EMS: Major Alarm Cleared.
243 INFORMATIONAL Major Alarm Cleared.
emsMinorAlarmAPC EMS: Minor Alarm.
244 MAJOR Minor Alarm.
emsMinorAlarmClearedAPC EMS: Minor Alarm Cleared.
245 INFORMATIONAL Minor Alarm Cleared.
emsOutletStateAbnormalAPC EMS: Outlet has changed to its abnormal state.
246 WARNING Outlet has changed to its abnormal state.
emsOutletStateNormalAPC EMS: Outlet has changed to its normal state.
247 INFORMATIONAL Outlet has changed to its normal state.
emsInputContactStateAbnormalAPC EMS: Input contact has changed to itsabnormal state.
248 WARNING Input contact has changed to its abnormal state.
emsInputContactStateNormalAPC EMS: Input contact has changed to its normalstate.
249 INFORMATIONAL Input contact has changed to its normal state.
emsOutputRelayStateAbnormalAPC EMS: Output Relay has changed to itsabnormal state.
250 WARNING Output Relay has changed to its abnormal state.
emsOutputRelayStateNormalAPC EMS: Output Relay has changed to its normalstate.
251 INFORMATIONAL Output Relay has changed to its normal state.
emsDeviceConfigChangeAPC: A device configuration change on a EMS.
252 INFORMATIONAL A device configuration change has been made on a EMS.
envHighTempThresholdViolationAPC ENV: High temperature threshold violation.
253 MAJOR High temperature threshold violation.
envHighTempThresholdViolationClearedAPC ENV: High temperature threshold violationcleared.
254 INFORMATIONAL High temperature threshold violation cleared.
envLowTempThresholdViolationAPC ENV: Low temperature threshold violation.
255 MAJOR Low temperature threshold violation.
envLowTempThresholdViolationClearedAPC ENV: Low temperature threshold violation
256 INFORMATIONAL Low temperature threshold violation cleared.
envHighHumidityThresholdViolationAPC ENV: High humidity threshold violation.
257 MAJOR High humidity threshold violation.
envHighHumidityThresholdViolationClearedAPC ENV: High humidity threshold violation
258 INFORMATIONAL High humidity threshold violation cleared.
envLowHumidityThresholdViolationAPC ENV: Low humidity threshold violation.
259 MAJOR Low humidity threshold violation.
envLowHumidityThresholdViolationClearedAPC ENV: Low humidity threshold violation cleared.
260 INFORMATIONAL Low humidity threshold violation cleared.
nlCommunicationEstablishedAPC NL: Communication Established.
261 INFORMATIONAL Communication Established.
nlCommunicationLostAPC NL: Communication Lost.
262 MAJOR Communication Lost.
nlDeviceConfigChangeAPC NL: Device Configuration Change.
263 INFORMATIONAL Device Configuration Change.
nlDoorUnlockedAPC NL: Door Unlocked.
264 INFORMATIONAL Door Unlocked.
nlAccountModificationAPC NL: Account Modification.
265 INFORMATIONAL Account Modification.
rPDUCommunicationEstablishedAPC Rack PDU: Communication established.
266 INFORMATIONAL Communication with a Rack PDU established.
rPDUCommunicationLostAPC Rack PDU: Communication lost.
267 MAJOR Communication with a Rack PDU has been lost.
rPDUOutletOnAPC Switched Rack PDU: An outlet has turned on.
268 INFORMATIONAL An outlet on a Switched Rack PDU has turned on.
rPDUOutletOffAPC Switched Rack PDU: An outlet has turned off.
269 INFORMATIONAL An outlet on a Switched Rack PDU has turned off.
rPDUDeviceConfigChangeAPC Rack PDU: Device configuration change made.
270 INFORMATIONAL Device configuration change has been made on a Rack PDU.
rPDUOutletConfigChangeAPC Switched Rack PDU: Outlet configurationchange made.
271 INFORMATIONALOutlet configuration change has been made on a SwitchedRack PDU.
rPDULowLoadAPC Rack PDU: Violation of low load threshold.
272 WARNING A Rack PDU has violated the low load threshold.
rPDULowLoadClearedAPC Rack PDU: Low load condition cleared.
273 INFORMATIONAL The low load condition on a Rack PDU has been cleared.
rPDUNearOverloadAPC Rack PDU: Near an overload condition.
274 WARNING A Rack PDU is near an overload condition.
rPDUNearOverloadClearedAPC Rack PDU: Near overload condition has
275 INFORMATIONAL Rack PDU near overload condition has cleared.
rPDUOverloadAPC Rack PDU: Overload condition.
276 MAJOR A Rack PDU is in an overload condition.
rPDUOverloadClearedAPC Rack PDU: Overload condition has cleared.
277 INFORMATIONAL The overload condition on a Rack PDU has cleared.
rPDUPowerSupply1FailAPC Rack PDU: Power Supply 1 is in FAIL state.
278 MAJOR Power Supply 1 on Rack PDU is in FAIL state.
rPDUPowerSupply1OkAPC Rack PDU: Power Supply 1 is operating
279 INFORMATIONAL Power Supply 1 on Rack PDU is operating normally.
rPDUPowerSupply2FailAPC Rack PDU: Power Supply 2 is in FAIL state.
280 MAJOR Power Supply 2 on Rack PDU is in FAIL state.
rPDUPowerSupply2OkAPC Rack PDU: Power Supply 2 is operating
281 INFORMATIONAL Power Supply 2 on Rack PDU is operating normally.
rPDUPhaseConfigChangeAPC Rack PDU: Phase configuration change made.
282 INFORMATIONAL Phase configuration change has been made on a Rack PDU.
rPDUCancelPendingCommandAPC Switched Rack PDU: Cancel PendingCommand made.
283 INFORMATIONALA Cancel Pending Command has been made on a SwitchedRack PDU.
aruAlinkCommunicationEstablishedAPC ARU: Communication Established.
284 INFORMATIONAL Communication Established.
aruAlinkCommunicationLostAPC ARU: Communication Lost.
285 MAJOR Communication Lost.
aruFanFailAPC ARU: Fan Fail.
286 MAJOR Fan Fail.
aruFanFailClearedAPC ARU: Fan Fail Cleared.
287 INFORMATIONAL Fan Fail Cleared.
aruSmokeAlarmAPC ARU: Smoke Alarm.
288 MAJOR Smoke Alarm.
aruSmokeAlarmClearedAPC ARU: Smoke Alarm Cleared.
289 INFORMATIONAL Smoke Alarm Cleared.
aruHighTemperatureAlarmAPC ARU: High Temperature Alarm.
290 MAJOR High Temperature Alarm.
aruHighTemperatureAlarmClearedAPC ARU: High Temperature Alarm Cleared.
291 INFORMATIONAL High Temperature Alarm Cleared.
aruExhaustTemperatureAlarmAPC ARU: Exhaust Temperature Alarm.
292 MAJOR Exhaust Temperature Alarm.
aruExhaustTemperatureAlarmClearedAPC ARU: Exhaust Temperature Alarm Cleared.
293 INFORMATIONAL Exhaust Temperature Alarm Cleared.
envAlinkCommunicationEstablishedAPC ENV: Communication Established.
294 INFORMATIONAL Communication Established.
envAlinkCommunicationLostAPC ENV: Communication Lost.
295 MAJOR Communication Lost.
emsAlinkPowerOverloadAPC EMS: Alink Power Overload.
296 MAJOR Alink Power Overload.
emsAlinkPowerOverloadClearedAPC EMS: Alink Power Overload Cleared.
297 INFORMATIONAL Alink Power Overload Cleared.
upsOutletGroupTurnedOnAPC UPS: Outlet Group turned on.
298 INFORMATIONAL Outlet Group turned on
upsOutletGroupTurnedOffAPC UPS: Outlet Group turned off.
299 WARNING Outlet Group turned off.
smwCriticalConditionAPC Symmetra MW UPS: A critical condition hasbeen detected.
300 MAJOR A critical condition has been detected.
smwCriticalConditionClearedAPC Symmetra MW UPS: A critical condition hasbeen cleared.
301 INFORMATIONAL A critical condition has been cleared.
smwWarningConditionAPC Symmetra MW UPS: A warning condition hasbeen detected.
302 WARNING A warning condition has been detected.
smwWarningConditionClearedAPC Symmetra MW UPS: A warning condition hasbeen cleared.
303 INFORMATIONAL A warning condition has been cleared.
smwInformationalConditionAPC Symmetra MW UPS: Informational conditiondetected.
304 INFORMATIONAL An informational condition has been detected.
smwInformationalConditionClearedAPC Symmetra MW UPS: Informational conditioncleared.
305 INFORMATIONAL An informational condition has been cleared.
Alert-Definition-Originator-MIB (F5emt2o.mib)
表21:Alert-Definition-Originator-MIB トラップ(ENTERPRISE : enterprises.211.4.1.4.6)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
ldsmTrap-MonitoredLDSM Monitored Event
1 INFORMATIONAL LDSM has reported: %s %s %s %s
ldsmTrap-InformationalLDSM Informational Event
2 INFORMATIONAL LDSM has reported: %s %s %s %s
ldsmTrap-RecoveredLDSM Recovered Event
4 INFORMATIONAL LDSM has reported: %s %s %s %s
ldsmTrap-NonCriticalLDSM NonCritical Event
8 INFORMATIONAL LDSM has reported: %s %s %s %s
ldsmTrap-CriticalLDSM Critical Event
16 INFORMATIONAL LDSM has reported: %s %s %s %s
ldsmTrap-NonRecoverableLDSM NonRecoverable Event
32 INFORMATIONAL LDSM has reported: %s %s %s %s
LDSM-MIB (ldsm.mib)
表22:LDSM-MIB トラップ(ENTERPRISE : enterprises343.2.5.1.3)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
ldsmOKTrapIntel LANDeskョ Server Manager has reported astatus OK event.
1 INFORMATIONALIntel LANDeskョ Server Manager has reported: The computer'sstatus is %s.
ldsmInformationalTrapIntel LANDeskョ Server Manager has reported astatus Informational event.
2 INFORMATIONALIntel LANDeskョ Server Manager has reported: The computer'sstatus is %s.
ldsmWarningTrapIntel LANDeskョ Server Manager has reported astatus Warning event.
3 MINORIntel LANDeskョ Server Manager has reported: The computer'sstatus is %s.
ldsmCriticalTrapIntel LANDeskョ Server Manager has reported astatus Critical event.
4 CRITICALIntel LANDeskョ Server Manager has reported: The computer'sstatus is %s.
LDCM-MIB (Ldcm.mib)
表23:LDCM-MIB トラップ(ENTERPRISE : enterprises343.2.5.1.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
ldcmUnknownTrapIntelョ LANDeskョ Client Manager has reported anUnknown event.
1 INFORMATIONAL Client Manager has reported an event on the computer %s: %s
ldcmInfoTrapIntelョ LANDeskョ Client Manager has reported anInformational event.
2 INFORMATIONAL Client Manager has reported an event on the computer %s: %s
ldcmOkTrapIntelョ LANDeskョ Client Manager has reported aseverity OK event.
3 INFORMATIONAL Client Manager has reported an event on the computer %s: %s
ldcmWarningTrapIntelョ LANDeskョ Client Manager has reported aseverity Warning event.
4 MINOR Client Manager has reported an event on the computer %s: %s
ldcmCriticalTrapIntelョ LANDeskョ Client Manager has reported aseverity Critical event.
5 CRITICAL Client Manager has reported an event on the computer %s: %s
ldcmFatalTrapIntelョ LANDeskョ Client Manager has reported aseverity Fatal event.
6 CRITICAL Client Manager has reported an event on the computer %s: %s
FUJITSU-SERVERVISOR-MIB (Servervi.mib)
表24:FUJITSU-SERVERVISOR-MIB トラップ(ENTERPRISE : enterprises.211.4.36.1.1.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
svisorTrapTypeServervisor Event
32 INFORMATIONAL Servervisor has reported: %s
RFC1157 (RFC1157.mib)
表25:RFC1157(Microsoft) トラップ(ENTERPRISE : enterprises.311.1.1.3.1.x)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
rfc1157ColdStartCold start
0 MINOR Station reinitialized. SNMPサービスが起動した。
次の表は、FUJITSU-SERVERVISOR-MIBのトラップを掲載して、概要を示したものです。富士通Servervisorからのトラップです。詳細についてはServervisorの説明書を参照してください。
次の表は、RFC1157のトラップを掲載して、概要を示したものです。詳細についてはRFC1157を参照してください。
次の表は、LDSM-MIBのトラップを掲載して、概要を示したものです。富士通 LDSMからのトラップです。詳細についてはLDSMの説明書を参照してください。
次の表は、LDCM-MIBのトラップを掲載して、概要を示したものです。富士通 LDSMからのトラップです。詳細についてはLDSMの説明書を参照してください。
次の表は、Alert-Definition-Originator-MIBのトラップを掲載して、概要を示したものです。富士通 LDSMからのトラップです。詳細についてはLDSMの説明書を参照してください。
rfc1157WarmStartWarm start
0 MINOR Station reinitialized. SNMPサービスが再起動した。
rfc1157LinkDownLink down
0 CRITICAL Communication link failed at the station %d. インタフェースがダウンした。
rfc1157LinkUpLink up
0 MINOR Communication link restored at the station %d. インタフェースがアップした。
rfc1157AuthenticationFailureAuthentication failure
0 MINOR Unauthorized message received.不正なcommunityでSNMPリクエストパケットを受け取った。
rfc1157EGPNeighborLostEGP neighbor lost
0 MAJOR Neighboring station down.
ROMPILOT-MIB (ROMPILOT.MIB)
表26:ROMPILOT-MIB トラップ(ENTERPRISE : enterprises.2487)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
rpWarmResetTrapRomPilot Warm Reset Trap.
257 INFORMATIONALRomPilot machine %s with MAC address %m has performed awarm reset and is running the BIOS POST.
rpColdResetTrapRomPilot Cold Reset Trap.
258 INFORMATIONALRomPilot machine %s with MAC address %m has performed acold reset and is running the BIOS POST.
rpDiagResetTrapRomPilot Diagnostic Reset Trap.
259 MINORRomPilot machine %s with MAC address %m has performed adiagnostic reset and is running the BIOS POST.
rpIDEResetTrapRomPilot IDE disk Reset Trap.
260 MINORRomPilot machine %s with MAC address %m has performed anIDE disk reset and is running the BIOS POST.
rpBootTrapRomPilot OS Boot Trap.
512 INFORMATIONALRomPilot machine %s with MAC address %m is starting to bootits Operating System.
rpPostFtlErrorTrapRomPilot Fatal POST Error Trap.
769 MAJORRomPilot machine %s with MAC address %m has detected afatal error during BIOS POST.
rpPostConErrorTrapRomPilot Conditional POST Error Trap.
770 MINORRomPilot machine %s with MAC address %m has detected aconditional error during BIOS POST.
rpPostWarngTrapRomPilot Conditional POST Error Trap.
771 MINORRomPilot machine %s with MAC address %m has detected aconditional error during BIOS POST.
rpSecurityTrapRomPilot Security Breach Trap.
1024 MAJORRomPilot machine %s with MAC address %m has detected anattempted security breach.
rpNosUpTrapRomPilot OS Loaded Trap.
1280 INFORMATIONALRomPilot machine %s with MAC address %m has loaded itsOperating System.
rpCriticalTrapRomPilot Critical Trap.
1536 MAJORRomPilot machine %s with MAC address %m has sent a criticaltrap.
rpDisconnectTrapRomPilot Disconnect Trap.
1792 INFORMATIONALRomPilot machine %s with MAC address %m has sent adisconnect trap and will end communications abruptly.
rpReconnectTrapRomPilot Reconnect Trap.
2048 INFORMATIONALRomPilot machine %s with MAC address %m has sent areconnect trap. This means that the RomPilot enabledmachine is able to resume communications.
rpPostWarningTrapRomPilot POST Warning Trap.
16384 MINORRomPilot machine %s with MAC address %m has detected awarning during BIOS POST.
rpPostConditionalTrapRomPilot Conditional POST Error Trap.
32768 MINORRomPilot machine %s with MAC address %m has detected aconditional error during BIOS POST.
rpPostFatalTrapRomPilot Fatal POST Error Trap.
49152 MAJORRomPilot machine %s with MAC address %m has detected afatal error during BIOS POST.
SW-MIB (fcswitch.mib)
表27:SW-MIB トラップ(ENTERPRISE : enterprises.1588.2.1.1.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
swFaultSwitch is faulty.
1 CRITICAL Faulty reason: %d
swSensorScnA sensor (temperature, fan, etc.) changed itsoperational state.
2 INFORMATIONAL %s: is currently in state %d
swFCPortScnA Fibre Channel Port changed its operational state.
3 INFORMATIONAL Port Index %d changed state to %d
swEventTrapA firmware event has been logged
4 INFORMATIONAL Event %d: %s (severity level %d) - %s
swFabricWatchTrapFabric Watch has generated an event
5 MINORThreshold %s in Class/Area %d at index %d has generatedevent %d with %d on %s. This event is %d
swTrackChangesTrapTrack changes has generated a trap
6 INFORMATIONAL %s
ADAPTECDURALINK-MIB (duralink.mib)
表28:ADAPTECDURALINK-MIB トラップ(ENTERPRISE : enterprises.1588.2.1.1.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
duralinkStatusTrapPort Status Changed
1 INFORMATIONAL Group %d Port %d port status is %d.
duralinkPortUpPort Available
2 INFORMATIONAL Group %s Port %s is up.
duralinkPortDownPort Unavailable
3 MAJOR Group %s Port %s is down.
duralinkPortStandbyPort acting as failover backup
4 INFORMATIONAL Group %s Port %s is acting as a failover backup.
次の表は、ADAPTECDURALINK-MIBのトラップを掲載して、概要を示したものです。Duralink(アダプテック マルチポートアダプタ:10Mbps/100Mbps対応のマルチポートファストイーサネットネットワークインターフェイスカード)からのトラップです。
次の表は、ROMPILOT-MIBのトラップを掲載して、概要を示したものです。ROM PILOT(phoenix BIOS)からのトラップです。
次の表は、SW-MIBのトラップを掲載して、概要を示したものです。Fibre Channel Switch SN200からのトラップです。詳細についてはSN200の説明書を参照してください。
TapeAlert-MIB (tapealrt.mib)
表29:TapeAlert-MIB トラップ(ENTERPRISE : enterprises.11.2.3.9.7.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
tapeAlertTrap1HP TapeAlert #1
1 MINORHba%d:Channel%d:ScsiID%d Tape Device Has ProblemsReading Data
Tape Device監視のTrapです。サポートしていません。
tapeAlertTrap2HP TapeAlert #2
2 MINORHba%d:Channel%d:ScsiID%d Tape Device Has Problems WritingData
↑
tapeAlertTrap3HP TapeAlert #3
3 MINORHba%d:Channel%d:ScsiID%d Tape Device Has Detected Reador Write Data Error
↑
tapeAlertTrap4HP TapeAlert #4
4 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Detected FaultyMedia [%s]
↑
tapeAlertTrap5HP TapeAlert #5
5 CRITICALHba%d:Channel%d:ScsiID%d Tape Device May Have Read Fault- Call Helpline
↑
tapeAlertTrap6HP TapeAlert #6
6 CRITICALHba%d:Channel%d:ScsiID%d Tape Device May Have Write Fault- Call Helpline
↑
tapeAlertTrap7HP TapeAlert #7
7 MINORHba%d:Channel%d:ScsiID%d Tape Device Has Detected WornOut Media [%s]
↑
tapeAlertTrap8HP TapeAlert #8
8 MINORHba%d:Channel%d:ScsiID%d Media Loaded In Tape Device IsNot Data Grade
↑
tapeAlertTrap9HP TapeAlert #9
9 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Attempted Backup toWrite-Protected Tape
↑
tapeAlertTrap10HP TapeAlert #10
10 INFORMATIONALHba%d:Channel%d:ScsiID%d Tape Device Eject AttemptedWhen Media Locked
↑
tapeAlertTrap11HP TapeAlert #11
11 INFORMATIONALHba%d:Channel%d:ScsiID%d Tape Device AttemptedBackup/Restore To Cleaning Tape
↑
tapeAlertTrap12HP TapeAlert #12
12 INFORMATIONALHba%d:Channel%d:ScsiID%d Media Loaded In Tape Device IsUnsupported Type
↑
tapeAlertTrap13HP TapeAlert #13
13 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has DetectedSnapped Tape
↑
tapeAlertTrap14HP TapeAlert #14
14 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has DetectedSnapped Tape
↑
tapeAlertTrap15HP TapeAlert #15
15 MINORHba%d:Channel%d:ScsiID%d Tape Device Has Memory Chip inCartridge Failure [%s]
↑
tapeAlertTrap16HP TapeAlert #16
16 CRITICALHba%d:Channel%d:ScsiID%d Tape Cartridge Ejected WhileActively Writing/Reading
↑
tapeAlertTrap17HP TapeAlert #17
17 MINORHba%d:Channel%d:ScsiID%d Tape Device Has Detected ReadOnly Media
↑
tapeAlertTrap18HP TapeAlert #18
18 MINORHba%d:Channel%d:ScsiID%d Tape Device Has DetectedCorrupted Directory On Tape
↑
tapeAlertTrap19HP TapeAlert #19
19 INFORMATIONALHba%d:Channel%d:ScsiID%d Tape Device Has Detected WornOut Media [%s]
↑
tapeAlertTrap20HP TapeAlert #20
20 CRITICAL Hba%d:Channel%d:ScsiID%d Tape Device Needs Cleaning ↑
tapeAlertTrap21HP TapeAlert #21
21 MINORHba%d:Channel%d:ScsiID%d Tape Device Requests RoutineCleaning
↑
tapeAlertTrap22HP TapeAlert #22
22 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Detected WornOut Cleaning Cartridge
↑
tapeAlertTrap23HP TapeAlert #23
23 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Detected InvalidCleaning Cartridge
↑
tapeAlertTrap29HP TapeAlert #29
29 MINORHba%d:Channel%d:ScsiID%d Tape Device RequiresPreventative Maintenance
↑
tapeAlertTrap30HP TapeAlert #30
30 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Hardware Fault -Reset Drive
↑
tapeAlertTrap31HP TapeAlert #31
31 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Hardware Fault -Call Helpline
↑
tapeAlertTrap32HP TapeAlert #32
32 MINORHba%d:Channel%d:ScsiID%d Tape Device Has Host InterfaceFault
↑
tapeAlertTrap33HP TapeAlert #33
33 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Eject MediaRequest
↑
tapeAlertTrap34HP TapeAlert #34
34 MINORHba%d:Channel%d:ScsiID%d Tape Device Has FirmwareDownload Fault
↑
tapeAlertTrap35HP TapeAlert #35
35 MINORHba%d:Channel%d:ScsiID%d Tape Device HumiditySpecification Exceeded
↑
tapeAlertTrap36HP TapeAlert #36
36 MINORHba%d:Channel%d:ScsiID%d Tape Device TemperatureSpecification Exceeded
↑
tapeAlertTrap37HP TapeAlert #37
37 MINORHba%d:Channel%d:ScsiID%d Tape Device Voltage SpecificationExceeded
↑
tapeAlertTrap38HP TapeAlert #38
38 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Predicted to Fail -Call Helpline
↑
tapeAlertTrap39HP TapeAlert #39
39 MINORHba%d:Channel%d:ScsiID%d Tape Device May Have HardwareFault - Run Diagnostics
↑
tapeAlertTrap40HP TapeAlert #40
40 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has AutoloaderCommunications Fault
↑
tapeAlertTrap41HP TapeAlert #41
41 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Detects Stray TapeIn Autoloader
↑
tapeAlertTrap42HP TapeAlert #42
42 MINORHba%d:Channel%d:ScsiID%d Tape Device Has AutoloaderMechanism Fault
↑
tapeAlertTrap43HP TapeAlert #43
43 CRITICALHba%d:Channel%d:ScsiID%d Tape Device Has Autoloader DoorOpen
↑
tapeAlertTrap44HP TapeAlert #44
44 CRITICALHba%d:Channel%d:ScsiID%d Autoloader Has Hardware Fault -Call Helpline
↑
tapeAlertTrap45HP TapeAlert #45
45 CRITICALHba%d:Channel%d:ScsiID%d Autoloader Cannot OperateWithout Magazine
↑
tapeAlertTrap46HP TapeAlert #46
46 MINORHba%d:Channel%d:ScsiID%d Autoloader Predicted to Fail - CallHelpline
↑
tapeAlertTrap256HP TapeAlert #256
256 CRITICALHba%d:Channel%d:ScsiID%d Library Has Drive CommunicationsFault
↑
tapeAlertTrap257HP TapeAlert #257
257 MINORHba%d:Channel%d:ScsiID%d Library Has Changer MechanismFault
↑
tapeAlertTrap258HP TapeAlert #258
258 CRITICALHba%d:Channel%d:ScsiID%d Library Has Hardware Fault -Reset Library
↑
tapeAlertTrap259HP TapeAlert #259
259 CRITICALHba%d:Channel%d:ScsiID%d Library Has Hardware Fault - CallHelpline
↑
tapeAlertTrap260HP TapeAlert #260
260 MINORHba%d:Channel%d:ScsiID%d Library May Have Hardware Fault- Run Diagnostics
↑
tapeAlertTrap261HP TapeAlert #261
261 CRITICAL Hba%d:Channel%d:ScsiID%d Library Has Host Interface Fault ↑
HP製 tape deviceからのトラップです。詳細についてはTape Deviceの説明書を参照してください。次の表は、TapeAlert-MIBのトラップを掲載して、概要を示したものです。
tapeAlertTrap262HP TapeAlert #262
262 MINORHba%d:Channel%d:ScsiID%d Library Predicted to Fail - CallHelpline
↑
tapeAlertTrap263HP TapeAlert #263
263 MINORHba%d:Channel%d:ScsiID%d Library Requires PreventativeMaintenance
↑
tapeAlertTrap264HP TapeAlert #264
264 CRITICALHba%d:Channel%d:ScsiID%d Library Humidity SpecificationExceeded
↑
tapeAlertTrap265HP TapeAlert #265
265 CRITICALHba%d:Channel%d:ScsiID%d Library Temperature SpecificationExceeded
↑
tapeAlertTrap266HP TapeAlert #266
266 CRITICALHba%d:Channel%d:ScsiID%d Library Voltage SpecificationExceeded
↑
tapeAlertTrap267HP TapeAlert #267
267 CRITICALHba%d:Channel%d:ScsiID%d Library Detects Stray Tape InDrive
↑
tapeAlertTrap268HP TapeAlert #268
268 MINORHba%d:Channel%d:ScsiID%d Library Has Problems PickingCartridge from Slot
↑
tapeAlertTrap269HP TapeAlert #269
269 MINORHba%d:Channel%d:ScsiID%d Library Has Problems PlacingCartridge into Slot
↑
tapeAlertTrap270HP TapeAlert #270
270 MINORHba%d:Channel%d:ScsiID%d Library Has Problems LoadingCartridge into Drive
↑
tapeAlertTrap271HP TapeAlert #271
271 CRITICAL Hba%d:Channel%d:ScsiID%d Library Door is Open ↑
tapeAlertTrap272HP TapeAlert #272
272 CRITICALHba%d:Channel%d:ScsiID%d Library Has Mechanical Fault withMailslot
↑
tapeAlertTrap273HP TapeAlert #273
273 CRITICALHba%d:Channel%d:ScsiID%d Library Cannot Operate WithoutMagazine
↑
tapeAlertTrap274HP TapeAlert #274
274 MINORHba%d:Channel%d:ScsiID%d Library Security Has BeenCompromised
↑
tapeAlertTrap275HP TapeAlert #275
275 INFORMATIONAL Hba%d:Channel%d:ScsiID%d Library Security Mode Changed ↑
tapeAlertTrap276HP TapeAlert #276
276 INFORMATIONAL Hba%d:Channel%d:ScsiID%d Library Manually Turned Offline ↑
tapeAlertTrap277HP TapeAlert #277
277 INFORMATIONAL Hba%d:Channel%d:ScsiID%d Library Drive Turned Offline ↑
tapeAlertTrap278HP TapeAlert #278
278 MINORHba%d:Channel%d:ScsiID%d Library Has Problems ReadingBarcode Labels
↑
tapeAlertTrap279HP TapeAlert #279
279 CRITICAL Hba%d:Channel%d:ScsiID%d Library Inventory is Inconsistent ↑
tapeAlertTrap280HP TapeAlert #280
280 MINORHba%d:Channel%d:ScsiID%d Invalid Library OperationAttempted
↑
IOMMIB (iommib.mib)
表30:IOMMIB トラップ(ENTERPRISE : enterprises.795.12.2)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
iomStorageControllerStateChangeIInformational Storage Controller State Change.
1010 INFORMATIONAL The storage controller %d has changed state.
iomStorageControllerStateChangeWWarning Storage Controller State Change.
1011 MAJOR The storage controller %d has changed state.
iomStorageControllerStateChangeCCritical Storage Controller State Change.
1012 CRITICAL The storage controller %d has changed state.
iomBusPortStateChangeIInformational Bus Port State Change.
1020 INFORMATIONAL The bus port %d has changed state.
iomBusPortStateChangeWWarning Bus Port State Change.
1021 MAJOR The bus port %d has changed state.
iomBusPortStateChangeCCritical Bus Port State Change.
1022 CRITICAL The bus port %d has changed state.
iomStorageDeviceStateChangeIInformational Storage Device State Change.
1030 INFORMATIONAL The storage device %d has changed state.
iomStorageDeviceStateChangeWWarning Storage Device State Change.
1031 MAJOR The storage device %d has changed state.
iomStorageDeviceStateChangeCCritical Storage Device State Change.
1032 CRITICAL The storage device %d has changed state.
iomVolumeSetStateChangeIInformational Volume Set State Change.
1040 INFORMATIONAL The volume set %d has changed state.
iomVolumeSetStateChangeWWarning Volume Set State Change.
1041 MAJOR The volume set %d has changed state.
iomVolumeSetStateChangeCCritical Volume Set State Change.
1042 CRITICAL The volume set %d has changed state.
iomVolumeSetActivityChangeIInformational Volume Set Activity Change.
1050 INFORMATIONAL The volume set %d has changed activity.
iomVolumeSetActivityChangeWWarning Volume Set Activity Change.
1051 MAJOR The volume set %d has changed activity.
iomVolumeSetActivityChangeCCritical Volume Set Activity Change.
1052 CRITICAL The volume set %d has changed activity.
iomSpareStateChangeIInformational Spare State Change.
1060 INFORMATIONAL The spare %d has changed state.
iomSpareStateChangeWWarning Spare State Change.
1061 MAJOR The spare %d has changed state.
iomSpareStateChangeCCritical Spare State Change.
1062 CRITICAL The spare %d has changed state.
iomEnclosureStateChangeIInformational Enclosure State Change.
1070 INFORMATIONAL A component in IOManager enclosure %d has changed state.
iomEnclosureStateChangeWWarning Enclosure State Change.
1071 MAJOR A component in IOManager enclosure %d has changed state.
iomEnclosureStateChangeCCritical Enclosure State Change.
1072 CRITICAL A component in IOManager enclosure %d has changed state.
次の表は、IOMMIBのトラップを掲載して、概要を示したものです。Adaptec IOManager Storage Controllersからのトラップです。
BRIDGE-MIB (trap1493.mib)
表31:BRIDGE-MIB トラップ(ENTERPRISE : mib2.17)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
newRoota new root of the Spanning True trap
1 INFORMATIONALA trap to inicated when a node has become a new root of theSpanning True
topologyChangetopology changed trap
2 INFORMATIONAL A trap to inicated when the topology has changed
RMON-MIB (trap1757.mib)
表32:RMON-MIB トラップ(ENTERPRISE : mib2.16)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
risingAlarmRising Alarm Trap Sent From Rmon Manager thatthe monitor variables has crosses its risingthreshold
1 INFORMATIONAL
The vairable %x we are monitoring has occured a Rising Alarm,The alarmValue is %d which has crossed over the threshold %dwithin the timeInterval we defined in Alarm Table. Note: Theinfomration of this alarm can be get from alarm Table index %dand the alarm SampleType is %d.
fallingAlarmFaling Alarm Trap Sent From Rmon Manager thatthe monitor variables has crosses its fallingthreshold
2 INFORMATIONAL
The vairable %x we are monitoring has occured a FallingAlarm, The alarmValue is %d which has crossed down thethreshold %d within the timeInterval we defined in Alarm Table.Note: The infomration of this alarm can be get from alarmTable index %d and the alarm SampleType is %d.
INTEL-WFM-MIB (WFM.mib )
表33:INTEL-WFM-MIB トラップ(ENTERPRISE : enterprises.3183.1.1)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
wfmEmergencyPowerOffEmergency PowerOff
1208068 INFORMATIONALEmergency PowerOff, if Server failed to boot DiagnosticSystem. Details: %s
wfmDiagnosticSystemBootDiagnostic System boot
1928964 INFORMATIONAL Server boots to Diagnostic System. Details: %s
EM4513-MIB (unicorn-trap.mib)
表34:EM4513-MIB トラップ(ENTERPRISE : enterprises.259.6.10.39)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
swTemperatureOverHeatTrapTemperature over heat
1 CRITICAL Temperature in chasis is too high.
NET-SNMP-MIB (net-snmp.mib)
表35:NET-SNMP-MIB トラップ(ENTERPRISE : enterprises.8072.4)
TRAP-TYPE/アラーム タイプ Specific エラーのクラス詳細メッセージ(%d:任意の数字、%s:システム変数)
備考
nsNotifyStartThe agent has started running.
1 INFORMATIONAL An indication that the agent has started running.
nsNotifyShutdownThe agent is in the process of being shut down.
2 INFORMATIONALAn indication that the agent is in the process of being shutdown.
nsNotifyRestartThe agent has been restarted.
3 INFORMATIONAL An indication that the agent has been restarted.
次の表は、NET-SNMP-MIBのトラップを掲載して、概要を示したものです。Linux Net-SNMPからのトラップです。
Wired for Managementからのトラップです。
次の表は、EM4513-MIBのトラップを掲載して、概要を示したものです。
BRIDGE装置からのトラップです。詳細についてはRFC1493を参照してください。
次の表は、RMON-MIBのトラップを掲載して、概要を示したものです。リモートネットワークモニタからのトラップです。詳細についてはRFC1757を参照してください。
次の表は、INTEL-WFM-MIBのトラップを掲載して、概要を示したものです。
次の表は、BRIDGE-MIBのトラップを掲載して、概要を示したものです。