Rx330s1 Og En

8/13/2019 Rx330s1 Og En

1/66

PRIMERGY RX330 S1ServerOptions Guide

Edition August 2009

8/13/2019 Rx330s1 Og En

2/66

Comments Suggestions Corrections The User Documentation Department would like toknow your opinion of this manual. Your feedback helpsus optimize our documentation to suit your individualneeds.

Feel free to send us your comments by e-mail [email protected] .

Certified documentationaccording to DIN EN ISO 9001:2000To ensure a consistently high quality standard anduser-friendliness, this documentation was created tomeet the regulations of a quality management systemwhich complies with the requirements of the standard

DIN EN ISO 9001:2000.cognitas. Gesellschaft fr Technik-Dokumentation mbHwww.cognitas.de

Copyright and TrademarksCopyright 2009 Fujitsu Technology Solutions GmbH.

All rights reserved.Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.
mailto:[email protected]://www.cognitas.de/http://www.cognitas.de/mailto:[email protected]

8/13/2019 Rx330s1 Og En

3/66

RX330 S1 Options Guide

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Concept and target groups . . . . . . . . . . . . . . . . . . . 5

1.2 Overview of the documentation . . . . . . . . . . . . . . . . . 5

1.3 Extensions and conversions . . . . . . . . . . . . . . . . . . 7

1.4 Notational conventions . . . . . . . . . . . . . . . . . . . . . 8

2 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 174.2 Removing the air duct . . . . . . . . . . . . . . . . . . . . . 19

5 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.1 Installing a second processor . . . . . . . . . . . . . . . . . 21

6 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.1 Equipping rules . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.2 Extending/replacing the main memory . . . . . . . . . . . . 30

7 Accessible drives . . . . . . . . . . . . . . . . . . . . . . . 33

7.1 Installing an accessible 5.25-inch drive . . . . . . . . . . . . 33

8/13/2019 Rx330s1 Og En

4/66

Options Guide RX330 S1

Contents

8 Expansion boards . . . . . . . . . . . . . . . . . . . . . . . . 37

8.1 Installing an expansion board . . . . . . . . . . . . . . . . . 37

8.2 Changing the riser card . . . . . . . . . . . . . . . . . . . . . 45

8.3 Installing the SAS RAID controller D2516 . . . . . . . . . . . 468.3.1 Assembling the SAS RAID controller D2516 . . . . . . . . . . . 468.3.2 Cabling SAS RAID controller . . . . . . . . . . . . . . . . . . . 50

9 Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

9.1 Inserting the air duct . . . . . . . . . . . . . . . . . . . . . . 59

9.2 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 60

10 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

10.1 Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

8/13/2019 Rx330s1 Og En

5/66

RX330 S1 Options Guide 5

1 Introduction

The PRIMERGY RX330 S1 server is an AMD-based server for small andmedium-sized networks. The PRIMERGY RX330 S1 is the perfect choice foroperational areas data centers, Internet- and application-hosting.

1.1 Concept and target groups

This Options Guide shows you how to extend and upgrade your server.

VCAUTION!

The activities described in this manual may only be performed bytechnical specialists.

I The installation and removal of the hot-plug components is described inthe Operating Manual supplied with the server.

1.2 Overview of the documentation

More information on your PRIMERGY RX330 S1 can be found in the followingdocuments:

Quick Start Hardware - PRIMERGY RX330 S1 leaflet (only included as aprinted copy)

Quick Start Software - Quick Installation Guide leaflet (only included as aprinted copy)

Safety notes and other important information manual

Warranty manual

Ergonomics manual

Returning used devices manual

Helpdesk leaflet

Technical manual for the system board D2440/D2932

PRIMERGY RX330 S1 Server Operating Manual

PRIMERGY RX330 S1 Server Options Guide

8/13/2019 Rx330s1 Og En

6/66

6 Options Guide RX330 S1

Overview of the documentation Introduction

ServerView RAID Manager Operating Manual

Integrated RAID for SAS Users Guide

Integrated Mirroring Users Guide LSI SATA Software RAID Users Guide

BIOS Setup manual

I PRIMERGY manuals are available in PDF format on the ServerViewSuite DVD 2 (ServerBooks). This DVD is part of the ServerView Suitesupplied with every server.

The PDF files of the manuals can also be downloaded free of charge

from the Internet. The overview page showing the online documentationavailable on the Internet can be found using the URL:http://manuals.fujitsu-siemens.com . The PRIMERGY server documentationcan be accessed using the Industry standard servers navigation option.

If you need a replacement copy of the ServerView Suite DVD2, send thedetails of your server to the following e-mail address: Reklamat-PC-

[email protected]

Further sources of information:

PRIMERGY Abbreviations and Glossary on the PRIMERGYServerView Suite DVD 2

Manual for the monitor Documentation for the boards and drives Operating system documentation Information files in your operating system
http://manuals.fujitsu-siemens.com/mailto:[email protected]:[email protected]:[email protected]:[email protected]://manuals.fujitsu-siemens.com/

8/13/2019 Rx330s1 Og En

7/66


Introduction Extensions and conversions

1.3 Extensions and conversions

Second processor

The server can be upgraded to a so-called dual processor system. A dualprocessor system needs a multi processor operating system. The secondprocessor must have the same type and clock rate as the first.

Extension of the main memory

Eight slots (4 banks with 2 modules) are available for the main memory. Eachmemory bank can be populated with 512 Mbyte (only D2440), 1 Gbyte, 2 Gbyte

or 4 Gbyte ECC DDR 2 SDRAM memory modules.If the memory modules are populated in pairs, each pair must consist ofidentical memory modules (2-way interleaved mode).

Additional accessible drive

One 5.25-inch bay is available for accessible drives.

Expansion boards in the PCI slots

The system board offers 1x PCI-Express x8 slot.

Additional the following slots are available by a riser card:

1 x PCI Express x8 slot, 1 x PCI Express x4 slot and1 x PCI-X (64 Bit / 66 MHz, ZCR) slot, or

1 x PCI Express x8 slot, 1 x PCI-X (64 Bit / 66 MHz) slot and1 x PCI-X (64 Bit / 66 MHz, ZCR) slot.

8/13/2019 Rx330s1 Og En

8/66


Notational conventions Introduction

1.4 Notational conventions

The following notational conventions are used in this manual:

Text in italics indicates commands, menu items or software programs.

Quotation marks indicate names of chapters and terms that are beingemphasized.

describes activities that must be performed in the ordershown.

V CAUTION! pay particular attention to texts marked with this symbol.Failure to observe this warning may endanger your life,destroy the system or lead to the loss of data.

I indicates additional information, notes and tips.

8/13/2019 Rx330s1 Og En

9/66


2 Procedure

V CAUTION! The actions described in this manual should only be performed bytechnical specialists.

Equipment repairs should only be performed by service personnel.

Any unauthorized opening and improper repairs could expose theuser to risks (electric shock, energy hazards, fire hazards) and couldalso damage the equipment.

Any unauthorized opening of the device will result in the invalidationof the warranty and exclusion from all liability.

First of all please familiarize yourself with the safety instructions in thesection chapter Safety notes on page 11 et seq. .

Ensure that all required manuals (see Overview of the documentation onpage 5 ) are available, printing out the PDF files if necessary. You willdefinitely need the Operating Manual for the server and the TechnicalManual for the system board.

Shut down the server correctly, switch it off, pull out the power plug(s),and open the server as described in the chapter Preparation on page 17 etseq. .

Extend or upgrade your server as described in the relevant chapter.

I The Operating Manual for the server describes how youinstall/remove the hot-plug components. Close the server, connect it to the power outlet, and switch it on as described

in the chapter Completion on page 59 et seq. .

Start the operating system and, if necessary, configure it as required (seethe Operating Manual).

8/13/2019 Rx330s1 Og En

10/66

8/13/2019 Rx330s1 Og En

11/66


3 Safety notes

I The following safety instructions are also provided in the manual Safetynotes and other important information.This device complies with the relevant safety regulations for data processingequipment. If you have any questions about where you can set up the device,contact your sales outlet or our customer service team.

V CAUTION! The actions described in this manual should only be performed by

technical specialists.

Equipment repairs should only be performed by service personnel.

Any unauthorized opening and improper repairs could expose theuser to risks (electric shock, energy hazards, fire hazards) and couldalso damage the equipment.

Any unauthorized opening of the device will result in the invalidationof the warranty and exclusion from all liability.

Before starting up

V CAUTION! During installation and before operating the device, observe the

instructions on environmental conditions for your device.

If the device is brought in from a cold environment, condensation mayform both inside and on the outside of the device.

Wait until the device has acclimatized to room temperature and is

absolutely dry before starting it up. Material damage may be causedto the device if this requirement is not observed.

Transport the device only in the original packaging or in packagingthat protects it from knocks and jolts.

8/13/2019 Rx330s1 Og En

12/66


Safety notes

Installation and operation

V CAUTION! If the device is integrated in an installation that receives power from

an industrial (public) power supply network with the IEC309connector, the (public) power supply protection must comply with therequirements for the non-industrial (public) power supply networks forthe type A connector.

The device automatically sets itself to a voltage in the range ofWert. Make sure that your local voltage is within this range.

This device has a specially approved power cable and must only be

connected to a safety socket on the rack mains socket strip. The ON/OFF button does not disconnect the device from the mains

voltage. To completely disconnect it from the mains voltage, removethe power plug from the safety socket.

Always connect the device and the attached peripherals to the samepower circuit. Otherwise you run the risk of losing data if, for example,the server is still operating but the peripheral device (e.g. storagesubsystem) has failed during a power outage.

Take notice that the data cables to peripheral devices are adequatelyshielded.

To the LAN wiring the requirements apply in accordance with thestandards EN 50173 and EN 50174-1/2. As minimum requirementthe use of a protected LAN line of category 5 for 10/100 MBpsEthernet, and/or of category 5e for Gigabit Ethernet is considered.The requirements of the specification ISO/IEC 11801 are to beconsidered.

Route the cables in such a way that they do not form a potentialhazard and that they cannot be damaged. When connecting up adevice, refer to the relevant notes in this manual.

Never connect or disconnect data transmission lines during a storm(lightning hazard).

8/13/2019 Rx330s1 Og En

13/66


Safety notes

V CAUTION! Make sure that no objects (such as bracelets or paper clips) fall into

or liquids spill into the device (risc of electric shock or short circuit).

In emergencies (e.g. damaged casing, controls or cables, penetrationof liquids or foreign matter), switch off the device immediately, removethe power plug from the safety socket and contact your sales outlet orcustomer service team.

Proper operation of the device (in accordance with IEC 60950-1/ EN 60950-1) is only ensured if the casing is completely assembledand the rear covers for the installation openings have been put inplace (electric shock, cooling, fire protection, interferencesuppression).

Only install system expansions that satisfy the requirements andrules governing safety and electromagnetic compatibility and relatingto telecommunications terminal equipment. If you install other expan-sions, you may damage the system or violate the safety regulationsand regulations governing RFI suppression. Information on whichsystem expansions are suitable can be obtained from the customerservice centre or your sales outlet.

The components or parts marked with a warning label (e.g. lightningsymbol) may only be opened, removed or exchanged by authorized,qualified personnel.

The warranty expires if the device is damaged during the installationor replacement of system expansions.

You may only set those resolutions and refresh rates specified in theoperating manual of the monitor. Otherwise, you may damage yourmonitor. If you are in any doubt, contact your sales outlet or customerservice centre.

8/13/2019 Rx330s1 Og En

14/66


Safety notes

Batteries

V CAUTION! Incorrect replacement of batteries may result in a risk of explosion.

The batteries may only be replaced with identical batteries or with atype recommended by the manufacturer (see the technical manual forthe system board).

Replace the lithium-battery on the system board in accordance withthe instructions in the technical manual for the system board.

Working with CDs/DVDs and CD/DVD drives

When working with devices with CD/DVD drives, these instructions must befollowed.

V CAUTION! Only use CDs/DVDs that are in perfect condition in your server's

CD/DVD drive, in order to prevent data loss, equipment damage andinjury.

Check each CD/DVD for damage, cracks, breakages etc. beforeinserting it in the drive.

Note that any additional labels applied may change the mechanicalproperties of a CD/DVD and cause imbalance.

Damaged and imbalanced CDs/DVDs can break at high drive speeds(data loss).

Under certain circumstances, sharp CD/DVD fragments can piercethe cover of the CD/DVD drive (equipment damage) and can fly outof the device (danger of injury, particularly to uncovered body parts

such as the face or neck).

I You can prevent mechanical damage and damage to the CD/DVD drive,as well as premature CD/DVD wear, by observing the following sugges-tions:

Only insert CDs/DVDs in the drive when needed and remove themafter use.

Store the CDs/DVDs in suitable sleeves.

Protect the CDs/DVDs from exposure to heat and direct sunlight.

8/13/2019 Rx330s1 Og En

15/66


Safety notes

I Laser informationThe CD/DVD drive complies with IEC 60825-1 laser class 1.

V CAUTION!The CD/DVD drive contains a light-emitting diode (LED), which undercertain circumstances produces a laser beam stronger than laserclass 1. Looking directly at this beam is dangerous.

Never remove parts of the CD/DVD drive casing!

Modules with electrostatic-sensitive components

Systems and components that might be damaged by electrostatic discharge(ESD) are marked with the following label:

Figure 1: ESD label

When you handle components fitted with ESDs, you must observe the followingpoints under all circumstances:

Remove the power plug before installing or removing componentscontaining ESDs.

You must always discharge yourself of static charges (e.g. by touching agrounded object) before working.

The equipment and tools you use must be free of static charges.

Only touch the components at the positions highlighted in green (touchpoints).

Do not touch any exposed pins or conductors on a component.

Use a grounding cable designed for this purpose to connect yourself to thesystem unit as you install components.

8/13/2019 Rx330s1 Og En

16/66


Safety notes

Place all components on a static-safe base.

I You will find a detailed description for handling ESD components in therelevant European or international standards (DIN EN 61340-5-1,ANSI/ESD S20.20).

8/13/2019 Rx330s1 Og En

17/66


4 Preparation

V CAUTION!Observe the safety instructions in the chapter Safety notes on page 11 et seq. .

4.1 Opening the server

Terminate all applications and shut down the server correctly.

If your operating system has not switched off the server, press the on/offbutton.

Pull all power connectors out of the safety sockets.

Disconnect all cables on the rear of the server.

Figure 2: Pulling the server out of the rack

Loosen the two knurled screws (1) and pull the server as far as possible outof the rack.

If the server is difficult to reach in the rack cabinet after you have pulled it out orpartially extending telescopic rails are used, remove the server completely fromthe rack cabinet. If you do not want to remove the server, skip the following twosteps.

Push the safety springs (2) on both sides and carefully pull the serveroutward.

Pull the server out of the rails and place it on a table, for example.

12

8/13/2019 Rx330s1 Og En

18/66


Opening the server Preparation

Figure 3: Loosening the screws

Unlock the top cover by removing the knurled screw at the rear side.

Pull the top cover approxiate 2 cm frontward using the handle.

Remove the top cover.

8/13/2019 Rx330s1 Og En

19/66


Preparation Removing the air duct

4.2 Removing the air duct

Remove the top cover as described in section Opening the server onpage 17 .

Figure 4: Removing the air duct

Take out the air duct.

8/13/2019 Rx330s1 Og En

20/66

8/13/2019 Rx330s1 Og En

21/66


5 Processors


V CAUTION!Processors are components which are extremely sensitive to electro-static discharges and must be handled with caution. After taking aprocessor out of its protective wrapper, set it on an insulated antistaticsurface with the smooth side down. Never slide a processor over asurface.

5.1 Installing a second processor

V CAUTION!For the PRIMERGY RX330 S1 server the system boards D2440 andD2932 are available. Make sure that the upgrade kit is suitable for your

system board.The system board can be upgraded with a second processor. The upgrade kitincludes a processor and a heat sink.

V CAUTION!You may only use processors of the same type on the system board. Thesecond processor must have the same type and clock rate as the first.Use a suitable multiprocessor operating system if dual operation isrequired.

Remove the top cover as described in section Opening the server onpage 17 .

Remove the air duct as described in section Removing the air duct onpage 19 .

8/13/2019 Rx330s1 Og En

22/66


Installing a second processor Processors

Installing the processor

Figure 5: Releasing the socket lever

Release the socket lever by pressing it downward and pull it upward until itstops.

Figure 6: Removing the protection cover

Remove the protection cover.

8/13/2019 Rx330s1 Og En

23/66


Processors Installing a second processor

Figure 7: Opening the processor holder

Open the processor holder.

Take out the processor from its protective wrapper.

Figure 8: Inserting the processor

Position the new processor over the socket, and insert it carefully into thesocket.

V CAUTION!The processor can only be installed in one particular direction. Payattention to the location mark on one of the corners and the recessesat the sides. Do not use force to press it into the socket to avoiddamaging the pins or the processor.

8/13/2019 Rx330s1 Og En

24/66



Figure 9: Closing the processor holder

Close the processor holder.

Figure 10: Locking the socket lever

Lock the processor into place in the socket by placing the socket lever in itsoriginal position.

Installing the heat sink

Remove the protective cover on the underside of the heat sink.

8/13/2019 Rx330s1 Og En

25/66



Figure 11: Installing the heat sink

Place the heat sink onto the processor socket as shown in the figure.Otherwise it is not possible to insert the air duct in the right way.

Figure 12: Hooking the clamp at the right side

Set the clamp on the heat sink and hook it on the distance holder at the rightside.

8/13/2019 Rx330s1 Og En

26/66



Figure 13: Hooking the clamp at the left side

Hook the clamp on the distance holder at the left side.

8/13/2019 Rx330s1 Og En

27/66



Figure 14: Engaging the locking lever

Press the two springs of the locking lever first somewhat outside and thendownward until they engage.

V CAUTION!Never operate a processor without heat sink or without processor fan asotherwise the processor may overheat and fail, causing the completesystem board to fail.

Install the air duct as described in section Inserting the air duct on page 59 .

Close the server, connect it to the mains, and switch it on as described insection Closing the server on page 60 et seq. .

8/13/2019 Rx330s1 Og En

28/66

8/13/2019 Rx330s1 Og En

29/66


6 Main memory


V CAUTION!For the PRIMERGY RX330 S1 server the system boards D2440 andD2932 are available. Make sure that the memory modules are suitablefor your system board.

The system board supports up to 32 Gbytes of main memory. Eight slots (4banks with 2 modules) are available for the main memory. Each memory bankcan be populated with 512 Mbyte (only D2440), 1 Gbyte, 2 Gbyte or 4 GbyteECC DDR2 SDRAM memory modules.The maximum main memory is 16 Gbytefor installation with one CPU and 32 GByte with two CPUs.

6.1 Equipping rules

Figure 15: Structure of the main memory

If the memory modules are populated in pairs, each pair must consist ofidentical memory modules (2-way interleaved mode)

The module capacity between pairs can differ: pair 2A/2B can be populatedwith two 1 Gbyte modules and pair 1A/1B with two 2 Gbyte modules.

D2440 ECC DDR2-533 (PC4300) or ECC DDR2-667 (PC5300)D2932 ECC DDR2-800 (PC6400)

CPU 1

DIMM1BDIMM1A

DIMM2B

DIMM2A

DIMM4ADIMM4B

DIMM3A

DIMM3B

CPU 2

8/13/2019 Rx330s1 Og En

30/66


Extending/replacing the main memory Main memory

CPU 2 must be installed to access DIMM3A/3B and DIMM4A/4B.

The table below shows the order in which the memory banks must bepopulated:

6.2 Extending/replacing the main memory

Open the server as described in the chapter Preparation on page 17 etseq. .

Figure 16: Removing a memory module

Press the holders on either side of the mounting location concerned outward(1).

DIMM2A

DIMM2B

DIMM1A

DIMM1B

2DIMMs

empty empty popu-lated

popu-lated

4DIMMs

popu-lated

popu-lated

popu-lated

popu-lated

CPU 1

DIMM2A

DIMM2B

DIMM1A

DIMM1B

DIMM4A

DIMM4B

DIMM3A

DIMM3B

4DIMMs


popu-lated


popu-lated

8DIMMs

popu-lated

popu-lated

popu-lated

popu-lated

popu-lated

popu-lated

popu-lated

popu-lated

CPU 1 CPU 2

1

1

2

8/13/2019 Rx330s1 Og En

31/66


Main memory Extending/replacing the main memory

If the mounting location was already equipped: pull the memory module outof the mounting location (2).

Figure 17: Inserting a memory module

Press the holders on either side of the mounting location concernedoutward.

Insert the memory module in the mounting location (1) until the holders atthe sides engage (2).

Close the server, connect it to the power outlet, and switch it on as describedin the chapter Completion on page 59 et seq. .

2

2

1

8/13/2019 Rx330s1 Og En

32/66

8/13/2019 Rx330s1 Og En

33/66


7 Accessible drives


7.1 Installing an accessible 5.25-inch drive

One 5.25-inch bay is available for accessible drives. The 5.25-inch drivesavailable are DVD-ROM, DVD-RW and tape drives. These drives can beinstalled in the free 5.25-inch bay.

I For installing a tape drive you need an additional SCSI controllerbecause there is no onboard SCSI controller on the system board. Open the server as described in the chapter Preparation on page 17 et

seq. .

Figure 18: Removing the dummy cover

Press the two locking levers of the dummy cover in direction of the arrowsand pull the dummy cover out of the bay.

V CAUTION!Keep the dummy cover for future use. If you remove the accessible driveagain and do not replace it with a new one, the dummy cover must be

reinstalled to comply with EMC regulations and to satisfy cooling require-ments and fire protection measures.

8/13/2019 Rx330s1 Og En

34/66


Installing an accessible 5.25-inch drive Accessible drives

Attach two guidance pins to the 5.25-inch drive.

I You will find a sac with the guidance pins in the drives bay. Otherwiseremove the guidance pins from the dummy cover.

Figure 19: Removing the guidance pins from the dummy cover

For installing a tape drive: install the SCSI controller in a PCI slot of the risercard as described in section Installing in PCI slots of the riser card onpage 39 .

Figure 20: Routing the SCSI cable

For installing a tape drive: route the SCSI cable as shown in the photo.

8/13/2019 Rx330s1 Og En

35/66


Accessible drives Installing an accessible 5.25-inch drive

Figure 21: Unlocking the bay

Pull up the locking lever of the bay.

Push the 5.25-inch drive into the bay until it is aligned to the server front side.

8/13/2019 Rx330s1 Og En

36/66


Installing an accessible 5.25-inch drive Accessible drives

Figure 22: Locking the bay

Push down the locking lever of the bay until it engages.

Connect the data cable to the 5.25-inch drive (see the cabling plans in theAppendix).

Connect the power cable to the 5.25-inch drive (see the cabling plans in theAppendix).


8/13/2019 Rx330s1 Og En

37/66


8 Expansion boards


The system board offers 1x PCI-Express x8 slot.

Additional the following slots are available by a riser card:

1 x PCI Express x8 slot, 1 x PCI Express x4 slot and1 x PCI-X (64 Bit / 66 MHz, ZCR) slot, or

1 x PCI Express x8 slot, 1 x PCI-X (64 Bit / 66 MHz) slot and1 x PCI-X (64 Bit / 66 MHz, ZCR) slot.

8.1 Installing an expansion board

Installing in PCI-Express x8 slot of the system board

Open the server as described in the chapter Preparation on page 17 et

seq. . Please read the documentation supplied with the expansion board.

If necessary, connect cables onto the expansion board.

Figure 23: Removing the screw

Remove the screw.

8/13/2019 Rx330s1 Og En

38/66


Installing an expansion board Expansion boards

Figure 24: Removing the PCI slots rear cover

Remove the PCI slots rear cover.

V CAUTION!Keep the rear cover of the PCI slot for future use. If you remove theexpansion board again and do not replace it with a new one, the rearcover must be reinstalled to comply with EMC regulations and tosatisfy cooling requirements and fire protection measures.

Figure 25: Installing the expansion board

Install the expansion board in the PCI slot of the system board. Make surethat the rear of the expansion boards slot cover is positioned in the intendedrecess.

8/13/2019 Rx330s1 Og En

39/66


Expansion boards Installing an expansion board

Fasten the expansion boards rear cover with the screw.

If required, connect the cables to the system board or other components.


Installing in PCI slots of the riser card


Remove all external cables being connected to installed expansion boards.

Figure 26: Pulling up the label

Pull up the green handle of the riser card holder using the label.

8/13/2019 Rx330s1 Og En

40/66



Figure 27: Removing the riser card holder

Take the riser card holder straight upward out of the housing using the greenhandle.

Please read the documentation supplied with the expansion board.

If necessary, connect cables onto the expansion board.

8/13/2019 Rx330s1 Og En

41/66



Figure 28: Riser card holder with riser card 1

Figure 29: Riser card holder with riser card 2

8/13/2019 Rx330s1 Og En

42/66



Figure 30: Loosening the rear cover

Loosen the screw and remove the PCI slots rear cover.

VCAUTION!

Keep the rear cover of the PCI slot for future use. If you remove theexpansion board again and do not replace it with a new one, the rearcover must be reinstalled to comply with EMC regulations and tosatisfy cooling requirements and fire protection measures.

8/13/2019 Rx330s1 Og En

43/66



Figure 31: Installing the expansion board

Install the expansion board in the PCI slot of the riser card. Make sure thatthe rear of the expansion boards slot cover is positioned in the intendedrecess.

Fasten the expansion boards slot cover with the screw.

8/13/2019 Rx330s1 Og En

44/66



Figure 32: Installing the riser card holder

Insert the riser card holder into the guidances (right side) and recesses (leftside) of the chassis.

Push the riser card into the PCI slot of the system board.

If required, connect the cables to the system board or other components. Close the server, connect it to the power outlet, and switch it on as described

in the chapter Completion on page 59 et seq. .

8/13/2019 Rx330s1 Og En

45/66


Expansion boards Changing the riser card

8.2 Changing the riser card


Remove the riser card holder and all expansion boards as described insection Installing in PCI slots of the riser card on page 39 .

Figure 33: Removing the riser card (photo shows riser card 2)

Loosen the four screws and remove the riser card.

Insert the new riser card and fasten it with the four screws.

Install the expansion boards and the riser card holder as described insection Installing in PCI slots of the riser card on page 39 .


8/13/2019 Rx330s1 Og En

46/66


Modular RAID configuration

8.3 Installing the SAS RAID controller D2516

8.3.1 Assembling the SAS RAID controller D2516 Open the server as described in the chapter Preparation on page 17 et

seq. .

Figure 34: Cougar kit contents

Check the contents of the D2516 kit:

1 Adapter bracket

2 BBU module (optional)

3 D2516 (LSI Cougar) controller

4 BBU cable (optional)

5 1x expanding rivet

4x screws and 4x spacer bolts for securing the BBU module (optional) on theadapter bracket2x screws (Y10C67 / M3x4.5) for securing the adapter bracket on the controller

8/13/2019 Rx330s1 Og En

47/66



Figure 35: Dislocating the BBU spacer bolt

Remove the spacer bolt from the BBU module (1).

Reattach the spacer bolt at the shown location (2).

Figure 36: Preparing the BBU module

Connect the BBU cable to the BBU module (1).

Route the BBU cable as shown (2).

Insert screws into the two lower spacer bolts (see circles) without tighteningthem (3).

1 2

1 2

3 3

8/13/2019 Rx330s1 Og En

48/66



Figure 37: Mounting the BBU module on the adapter bracket

Hook the two screws on the BBU module into the notches on the adapterbracket (1).

Align the two opposing spacer bolts on the BBU module with the drill holes

on the adapter bracket (2). Secure the BBU module on the adapter bracket with four screws (1 and 2).

Figure 38: Mounting the adapter bracket on the controller (A)

The expanding rivet has to be attached from the solder side of the controller.

1

2 2

1

8/13/2019 Rx330s1 Og En

49/66



Figure 39: Mounting the adapter bracket on the controller (B).

Connect the BBU cable to the controller (1).

Secure the controller on the adapter bracket with two screws (M3x4.5) (2)and the expanding rivet (3).

Install the controller in the PCI slot on the system board (see Options Guide).

I Before the next system restart, adjust the following BIOS setting: Under Advanced - PCI Configuration - Slot 4 Configuration set the BIOS ROM Scan option to Enabled .

123

8/13/2019 Rx330s1 Og En

50/66



8.3.2 Cabling SAS RAID controller

Figure 40: Disconnecting cables

FAN FAN FAN

D VD -RO M

M oboRedundantPSU J

4 8

J 4 9

J 5 1

J 8

IDE1 J40 J15

CPU1

J 1 0

J 2 5

J 2 1

J 1 7

CPU2

J22

ID temp

USB Front Panel

swi t ch

13

9

14

11

10

12

8

7

1

2

3

4

5

6

HDDw/B ackplane

HDDw/B ackplane

12

S A S 6

S A S 5

S A S 1

S A S 2

S A S 3

S A S 4

S A S 6

S A T A 1

8/13/2019 Rx330s1 Og En

51/66



Disconnect the following cables in order to complete the Modular RAIDconversion:

Cables to be disconnected

1 SAS cable, 320 mm (orange) -SATA 1

Disconnect from theleft-hand backplane2

SAS cable, 320 mm (blue) -SATA 2

3 SAS cable, 320 mm (black) -SATA 3

4SAS cable, 580 mm (orange) -SATA 4

Disconnect from theright-hand backplane5

SAS cable, 580 mm (blue) -SATA 5


7 HDD backplane data cable,380 mm (left)Disconnect from the systemboard and left-hand backplane

8 HDD backplane data cable,730 mm (right) Disconnect from the systemboard and right-hand backplane

8/13/2019 Rx330s1 Og En

52/66



Figure 41: Connecting cables

S A S 5

S A S 1

S A S 2

S A S 3

S A S 4

S A S 6

S A T A 1

FAN FAN FAN

HDDw/B ackplane

D VD -RO M

M obo RedundantPSU J

4 8

J 4 9

J 5 1

J 8

IDE1 J15J40

CPU1

J 1 0

J 2 5

J 2 1

J 1 7

CPU2

J22

ID temp

USB Front Panel

swi t ch

13

9

14

10

12

8

7

1

HDDw/B ackplane

9

11 D2516

MLC1 MLC2

B B U

T 2 6 1 3 9

- Y 3 9 6 4

- V 9 0 1

T 2 6 1 3 9

- Y 3 9 6 4

- V 9 0 2

0

2

4

5

6

11

8/13/2019 Rx330s1 Og En

53/66



Connect the following cables in order to complete the Modular RAIDconversion:

Cables to be connected

MLC1

0 SAS cable, 320 mm (orange) -SATA 0Reconnect tothe left-handbackplane

1 SAS cable, 320 mm (blue) -SATA 1


7 HDD backplane data cable,380 mm (left)

Reconnect L4 theSystem Boardconnector J51

Connect L3 to left-hand backplaneconnector J504

MLC2

4 SAS cable, 580 mm (orange) -SATA 4Reconnect to

the right-handbackplane

5SAS cable, 580 mm (blue) -SATA 5


8 HDD backplane data cable,730 mm (right)

Reconnect R4 theSystem Boardconnector J49,

Connect L3 to right-

hand backplaneconnector J504

8/13/2019 Rx330s1 Og En

54/66



Figure 42: Modular RAID cable connectors - left-hand backplane

Connect the Modular RAID cable T26139-Y3964-V901 as follows:

L1 to SAS RAID controller D2516 connector MLC1

L2 to left-hand HDD backplane SATA connectors 1, 2 and 3

L3 to left-hand HDD backplane connector J504

L4 to system board connector J51

L1

L2

L4

L3

8/13/2019 Rx330s1 Og En

55/66



Figure 43: Modular RAID cable connectors - right-hand backplane

Connect the Modular RAID cable T26139-Y3964-V902 as follows:

R1 to SAS RAID controller D2516 connector MLC2

R2 to right-hand HDD backplane SATA connectors 4, 5and 6

R3 to right-hand HDD backplane connector J504

R4 to system board connector J49

R1

R2

R4

R3

8/13/2019 Rx330s1 Og En

56/66



Figure 44: Routing the Modular RAID cables (A)

Route the Modular RAID cables T26139-Y3964-V901 and T26139-Y3964-V902as follows:

Route the thinner cables originating from connectors L3 / L4 or R3 / R4through the cable clamp on the side as shown (1).

Snap shut the cable clamp (2).

Figure 45: Routing the Modular RAID cables (B)

Guide the thicker cables heading towards the HDD backplanes (L2 or R2)around the fan cage as shown.

12

8/13/2019 Rx330s1 Og En

57/66



Figure 46: Routing the Modular RAID cables (C)

Route the thin cables originating from connectors R3 / R4 through the fourcable clamps on the fan:

1 from the controller towards the backplane2 from the backplane towards the system board

Route the thicker cables heading towards the right HDD backplane (R2) ontop of the cable clamps as shown.


1

2

8/13/2019 Rx330s1 Og En

58/66

8/13/2019 Rx330s1 Og En

59/66


9 Completion


9.1 Inserting the air duct

Figure 47: Inserting the air duct

Insert the air duct.

8/13/2019 Rx330s1 Og En

60/66


Closing the server Completion

9.2 Closing the server

Figure 48: Attaching the top cover

Position the top cover in such a way that it protrudes approxiate 2 cm at therear.

Push the top cover all the way in direction to the front side.

Fasten the top cover with the knurled screw.

8/13/2019 Rx330s1 Og En

61/66


Completion Closing the server

If you have not removed the server from the rack cabinet, please skip this page.

Push the server from the front side in the extended telescopic rails.

Reconnect all the cables you disconnected beforehand on the rear of theserver.

Figure 49: Installing the server in a rack cabinet

Press in the safety springs (1) on both sides and push the server as far as itwill go into the rack.

Fasten the server in the rack using the two knurled screws (2).

Connect all power plugs to the safety sockets.

Press the on/off button to start up the server.

21

8/13/2019 Rx330s1 Og En

62/66

8/13/2019 Rx330s1 Og En

63/66


10 Appendix

10.1 Cabling

The following table gives you an overview of the cables:

*refers to the drawings of the cabling

Cableno *

Part number Item number Designation Length

1 A3C40085575 SATA cable - SATA 6(black/black)

580 mm

2 A3C40085575 SATA cable - SATA 5 (blue/blue) 580 mm3 A3C40085575 SATA cable - SATA 4

(orange/orange)580 mm

4 A3C40085588 SATA cable - SATA 3(green/blue)

320 mm

5 A3C40085588 SATA cable - SATA 2 (red/black) 320 mm

6 A3C40085588 SATA cable - SATA 1(yellow/orange)

320 mm

7 A3C40085681 Backplane I2C cable (left side) 380 mm

8 A3C40085657 Backplane I 2C cable (right side) 730 mm

9 A3C40085686 IDtemp cable

10 A3C40085684 CD-/DVD-ROM cable

11 A3C40085685 USB cable

12 A3C40085682 Front panel cable

13 A3C40085683 Fan extension cable

14 A3C40085687 Intrusion switch cable 300 mm

8/13/2019 Rx330s1 Og En

64/66


Cabling Appendix

Figure 50: Cabling

F A N F A N F A N

HDDw/B ackplane

D VD -RO M

M oboRedund a ntPSU

S A S 5

S A S 1

J 4 8

J 4 9

J 5 1

S A S 2

S A S 3

S A S 4

S A S 6

J 8

IDE1 J15J40

CPU1

J 1 0

J 2 5

J 2 1

J 1 7

CPU2

J22

swi t c h

13

9

14

1 0

12

8

7

6

5

4

3

2

1

HDDw/B ackplane

9

11

ID temp

11 U S B Front P anel

8/13/2019 Rx330s1 Og En

65/66


Index

Aaccessible drives 7, 33air duct 19 , 59

Ccabling 64

Ddual operation 21

EESD (devices sensitive to electrostaticdischarge) 15

expansion board 7, 37

Hheat sink 24

Iinformation, additional 6

Llaser information 15light emitting diode (LED) 15lithium battery 14LSI Cougar 46

Mmain memory 7, 29meaning of the symbols 8Modular RAID 46multiprocessor operating system 21

Nnotational conventions 8

Pprocessor 7

heat sink 24

Rriser card 37

SSAS RAID controller D2516 46

Ttarget grou p 5top cover 18 , 60

8/13/2019 Rx330s1 Og En

66/66

Rx330s1 Og En

Documents

Transcript of Rx330s1 Og En