Paradise Datacom Indoor GaN 3RU SSPA 212463 RevC

8/11/2019 Paradise Datacom Indoor GaN 3RU SSPA 212463 RevC

1/10

Indoor Rack Mount

GaN Solid State Power Amplifiers3RU Rack Height

PAGE 1 OF 10 212463 REV C ECO 17667

Teledyne Paradise Datacom has a rich history in the designand production of Gallium Nitride (GaN) based SSPAs. Ourengineers utilize innovative linearization techniques thatenable GaN amplifiers to produce linear output power with thesame efficiency as tube based amplifier systems. A completefamily of Satcom amplifiers has been developed that coverS-Band through Ku-Band.

GaN amplifiers have a superior set of mutually beneficial char-acteristics, including:

Higher Output Power

Greater Power-Added Efficiency

High Reliability

These GaN amplifier modules are installed in the popular 3RU(5.25 inch high) Chassis, which features a front panel displayand five fault condition LEDs that reflect some of the SSPAmajor fault states. Local/Remote and Mute/Unmute LEDs showthe current control mode and mute state of the amplifier.

A full compliment of remote monitor and control of the amplifieris available at the rear panel, including: RS-232/RS-485; Ether-net, with UDP and SNMP control; Web Browser TCP/IP; andDiscrete hardware (parallel port) signals.

Teledyne Paradise Datacom LLC Teledyne Paradise Datacom Ltd.328 Innovation Blvd., Suite 100 2&3 The Matchyns, London Road, Rivenhall EndState College, PA 16803 USA Witham, Essex CM8 3HA United KingdomTel: (814) 238-3450 Tel: +44(0) 1376 515636Fax: (814) 238-3829 Fax: +44(0) 1376 533764www.paradisedata.com

650W X-Band 3RU SSPA Chassis with 1RU N+1 Power Supply

FEATURES

Extremely High PowerDensity:

to 600 W S-Band to 800 W X-Band

to 800 W C-Band to 500 W Ku-Band

Removable Fan Tray andMonitor & Control Card

Assembly

Remote Communicationvia RS232/485 or Ethernet

RF Output Sample Port

20 dB RF Gain Adjustment

True RF Output PowerMeasurement

OPTIONS

Remote Control Panel

L-Band Input operation

Reflected Power Monitor

Input Sample Port 1RU Redundant Power

Supply

Exhaust Duct Adapters

Redundant Systems

Phase Combined Systems


2/10

Indoor Rack Mount


PAGE 2 OF 10 212463 REV C ECO 17667

Specifications, S-Band SSPAs

PARAMETER NOTES LIMITS UNITS

Frequency Range Frequency selection GFrequency selection AFrequency selection B

1.750 to 2.1202.020 to 2.1202.200 to 2.300

GHzGHzGHz

Output PowerTypical, PsatGuaranteed minimum, PLinear

1HPAS3050ARXXXXXGHPAS3100ARXXXXXGHPAS3200ARXXXXXGHPAS3300ARXXXXXGHPAS3400ARXXXXXGHPAS3500ARXXXXXGHPAS3600ARXXXXXG

Psat/ PLinear47.0 (50) / 44.0 (25)50.0 (100) / 47.0 (50)

53.0 (200) / 50.0 (100)54.8 (300) / 51.8 (150)56.0 (400) / 53.0 (200)57.0 (500) / 54.0 (250)57.8 (600) / 54.8 (300)

dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)

Power RequirementsLine VoltageLine FrequencyTypical Line Power (typical)

power factor

HPAS3050ARXXXXXG

HPAS3100ARXXXXXGHPAS3200ARXXXXXGHPAS3300ARXXXXXGHPAS3400ARXXXXXGHPAS3500ARXXXXXGHPAS3600ARXXXXXG

.9890 to 26547 to 63

Psat/ PLinear400 / 300

500 / 400800 / 700

1300 / 10002000 / 13002100 / 15002200 / 1700

VACHz

W

WWWWWW

Receive Band Noise Power Density without optional filterwith optional filter

-95-155

dBW / 4 KHzdBW / 4 KHz

Note 1: PLinear= maxiumum output power at which third order internal products = -25 dBc.

Specifications, C-Band SSPAs


Frequency Range Frequency selection LFrequency selection HFrequency selection CFrequency selection AFrequency selection BFrequency selection D

4.400 to 5.0005.715 to 5.7905.750 to 6.6705.850 to 6.4255.850 to 6.7256.425 to 7.025

GHzGHzGHzGHzGHzGHz


1HPAC3050ARXXXXXGHPAC3100ARXXXXXGHPAC3150ARXXXXXGHPAC3200ARXXXXXGHPAC3300ARXXXXXGHPAC3400ARXXXXXGHPAC3650ARXXXXXGHPAC3800ARXXXXXG

Psat/ PLinear47.0 (50) / 44.0 (25)50.0 (100) / 47.0 (50)51.8 (150) / 48.8 (75)53.0 (200) / 50.0 (100)54.8 (300) / 51.8 (150)56.0 (400) / 53.0 (200)58.1 (650) / 55.1 (325)59.0 (800) / 56.0 (400)

dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)

Power RequirementsLine VoltageLine Frequency

Typical Line Power (typical)

power factor

HPAC3050ARXXXXXGHPAC3100ARXXXXXGHPAC3150ARXXXXXGHPAC3200ARXXXXXGHPAC3300ARXXXXXGHPAC3400ARXXXXXGHPAC3650ARXXXXXGHPAC3800ARXXXXXG

.9890 to 26547 to 63

Psat/ PLinear500 / 400600 / 5001000 / 8001100 / 880

1500 / 13001800 / 16003300 / 28004000 / 3500

VACHz

WWWWWWWW

Receive Band Noise Power Density without filter -155 dBW / 4 kHz



3/10

Indoor Rack Mount


PAGE 3 OF 10 212463 REV C ECO 17667

Specifications, X-Band SSPAs


Frequency Range Frequency selection FFrequency selection DFrequency selection A

7.10 to 7.407.70 to 8.407.90 to 8.40

GHzGHzGHz


1HPAX3300ARXXXXXGHPAX3400ARXXXXXGHPAX3650ARXXXXXGHPAX3800ARXXXXXG

Psat/ PLinear54.8 (300) / 51.8 (150)56.0 (400) / 53.0 (200)58.1 (650) / 55.1 (325)59.0 (800) / 56.0 (400)

dBm (W)dBm (W)dBm (W)dBm (W)

Power RequirementsLine VoltageLine FrequencyLine Power (typical)

power factorLine voltage

Line frequency

HPAX2300ARXXXXXGHPAX2400ARXXXXXGHPAX2650ARXXXXXGHPAX2800ARXXXXXG

.9890 to 26547 to 63

Psat/ PLinear1500 / 13002000 / 17003300 / 28004000 / 3500

VACHz

WWWW

Receive Band Noise Power Density without optional filterwith optional filter

-85-155

dBW / 4 kHzdBW / 4 kHz


Specifications, Ku-Band SSPAs


Frequency Range Frequency selection FFrequency selection BFrequency selection AFrequency selection CFrequency selection D

12.75 to 13.2513.75 to 14.5014.00 to 14.5014.50 to 14.7015.10 to 15.40

GHzGHzGHzGHzGHz

Output PowerTypical, Psat

Guaranteed minimum, PLinear1

HPAK3040ARXXXXXG

HPAK3050ARXXXXXGHPAK3080ARXXXXXGHPAK3100ARXXXXXGHPAK3150ARXXXXXGHPAK3200ARXXXXXGHPAK3250ARXXXXXGHPAK3300ARXXXXXGHPAK3400ARXXXXXGHPAK3500ARXXXXXG

Psat/ PLinear46.0 (40) / 43.0 (20)

47.0 (50) / 44.0 (25)49.0 (80) / 46.0 (40)50.0 (100) / 47.0 (50)51.8 (150) / 48.8 (75)53.0 (200) / 50.0 (100)54.0 (250) / 51.0 (125)54.8 (300) / 51.8 (150)56.0 (400) / 53.0 (200)57.0 (500) / 54.0 (250)

dBm (W)

dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)dBm (W)

Power RequirementsLine VoltageLine FrequencyLine Power (typical)

power factorLine voltage

Line frequency

HPAK3040ARXXXXXGHPAK3050ARXXXXXGHPAK3080ARXXXXXGHPAK3100ARXXXXXGHPAK3150ARXXXXXGHPAK3200ARXXXXXGHPAK3250ARXXXXXGHPAK3300ARXXXXXGHPAK3400ARXXXXXGHPAK3500ARXXXXXG

.9890 to 26547 to 63

Psat/ PLinear500 / 400600 / 500730 / 585900 / 7501000 / 8501200 / 9201500 / 10002000 / 15002500 / 17003000 / 2000

VACHz

WWWWWWWWWW

Receive Band Noise Power Density2 -155 dBW / 4 kHz

Note 1: PLinear= maxiumum output power at which third order internal products = -25 dBc.Note 2: All Ku-Band SSPAs are fitted with a receive band reject bulkhead filter, standard. An optional pressure window is available.


4/10

Indoor Rack Mount


PAGE 4 OF 10 212463 REV C ECO 17667

Common Electrical Specifications


GainGain Flatness

Gain Slope

Gain Variation vs. TemperatureGain Adjustment

rangefull band

full band (Extended C-Band)full band (S-Band)

per 40 MHzper 10 MHz (S-band)

0 C to +50 C0.1 dB resolution

55-75 1.0 1.5

0.75 0.3 0.3 1.020

dBdBdBdB

dB/40 MHzdB/10 MHz

dBdB

Intermodulation Distortion(Two-tone, 5 MHz spacing)

At PLinear(Psat- 3 dB) -25 dBc

AM/PM Conversion @ rated PLinear 1.0o/dB

SpuriousHarmonics (SSPA only)

@ rated PLinear@ rated PLinear

@ rated PLinear (S-Band)

-65-50-30

dBcdBcdBc

Input/Output VSWR All except Extended C-Band

Extended C-Band

1.30:1

1.50:1Noise Figure at maximum gain

at maximum gain (S-Band)108

dBdB

Group Delay(per 40 MHz segment)

LinearParabolic

Ripple

0.010.0031.0

ns/MHzns/MHz2

ns p-p

Transmit Band NoiseOutput Power Density

TX Band -75 dBW/4 KHz

Residual AM Noise, typical Offset frequency from carrier1 Hz

10 Hz100 Hz1 KHz

10 KHz100 KHz

1 MHz

-110-120-130-135-140-140

-140

dBc/HzdBc/HzdBc/HzdBc/HzdBc/HzdBc/Hz

dBc/HzResidual Phase Noise, typical(SSPA only)

Offset frequency from carrier10 Hz100 Hz1 KHz

10 KHz100 KHz1 MHz

-90-100-110-120-125-130


True RF Power Detector RangeAccuracy

Psatto (Psat - 20) 0.5

dBdBm

Specifications are subject to change without notice.


5/10

Indoor Rack Mount


PAGE 5 OF 10 212463 REV C ECO 17667

L-Band Operation

Teledyne Paradise Datacom amplifiers are available with an integrated L-Band Block UpConverter. The L-Band units utilize Teledyne Paradise Datacoms proprietary zBUCtechnology. The addition of a zBUC converter to the SSPA typically increases the gain by2-4 dB. Tha advantages of zBUC technology include: zBUC converter can detect and switch to an extenally supplied reference. Optional internal high stability (10MHz) reference. zBUC converter can lock to an externally supplied reference of 5, 10, 20, 25, or 50 MHz

without modification. zBUC converter can accept a wide range of external reference power (-10 to +5 dBm) zBUC converter can accept FSK monitor and control signal via the IFL for complete

amplifer remote control.

Electrical Specifications for 3RU RM GaN SSPA with zBUCconverter


GainGain FlatnessGain SlopeGain Adjusted Range

Gain Stability

Nominal settingfull band (C-,X-,Ku-bands)

per 40 MHz (C-,X-,Ku-bands)Range

Typical C-Band Adj. RangeTypical Ku-Band Adj. Range

0 to +50 C

752.00.520

60 - 8057 - 771.5

dBdB

dB/40 MHzdBdBdBdB

Phase Noise Offset frequency from carrier10 Hz

100 Hz1 KHz

10 KHz100 KHz1 MHz

Absolute max.-30-60-70-80-90-90

C-band (typ.)-60-80-80-85

-120-125

X-band (typ.)-60-75-75-100-110-122

Ku-band (typ.)-50-65-72-90-110-120


Spurious In-Band Signal Related (C-/Ku-Band)(Extended C-Band)

Close to Carrier Spurious (20 MHz)Local Oscillator

-50-40-50-30

dBcdBcdBcdBm

Noise Figure At 75 dB gain setting 20 dB

Input VSWR L-Band 1.5 : 1

Internal Reference Option Reference accuracy @ 25 CReference Stability over Temperature (-20 to +85 C)

1 10-8 3 10-8

Available Frequency Plans

Band Frequency Band IF Input LO Frequency RF Output Gain Change

C Standard C-Band 950 - 1525 MHz 4.900 GHz 5.850 - 6.425 GHz 0-4 dB

C Extended C-Band 950 - 1825 MHz 4.900 GHz 5.850 - 6.725 GHz 0-4 dB

C Palapa Band 950 - 1250 MHz 5.475 GHz 6.425 - 6.725 GHz 0-4 dB

C Insat Band 950 - 1250 MHz 5.775 GHz 6.725 - 7.025 GHz 0-4 dB

X Standard X-Band 950 - 1450 MHz 6.950 GHz 7.900 - 8.400 GHz 0-2 dB

Ku Ku-Band Sub-Band A 950 - 1450 MHz 13.050 GHz 14.00 - 14.50 GHz 0-2 dB

Ku Ku-Band Sub-Band B 950 - 1700 MHz 12.800 GHz 13.75 - 14.50 GHz 0-2 dB

Ku Ku-Band Sub-Band F 950 - 1450 MHz 11.800 GHz 12.75 - 13.25 GHz 0-2 dB


6/10

Indoor Rack Mount


PAGE 6 OF 10 212463 REV C ECO 17667

True RMS Output Power Measurement

Historically, Satcom SSPAs have utilized simple diode peak detectors for the measurement ofRF output power. This results in considerable error depending on the type of modulation andnumber of carriers that are being amplified. The new generation of Teledyne ParadiseDatacom SSPAs include true RMS output power detection. This means that the RF outputpower that is reported over the remote control is very near power meter accuracy.

1RU N+1 Redundant Power Supply

The combination of a separate, fully redundant power supply is an excellent means of obtain-ing the ultimate in system reliability.

The power supply is an N+1 redundant configuration, meaning that there is one more powersupply module available than required to operate the SSPA. A failure of one power supplymodule will not take the amplifier off the air.

In addition, the power supply modules are removable from the front panel while in operation.There is never a need to remove the power supply chassis from the equipment rack.

The power supply has a single phase, universal AC input rating from 90-265 VAC, 46-63 Hz.

It is power factor corrected to 0.99 and is configured with up to four hot-swappable powersupply modules, depending on the power requirements of the SSPA.


7/10

Indoor Rack Mount


PAGE 7 OF 10 212463 REV C ECO 17667

RF INPUT

SAMPLE

RF INPUT

SAMPLE

TELEDYNE

HPAS3-200200WS-BAND

RF OUTPUT

SAMPLE

RF OUTPUT

SAMPLE

RF IN

J1

J2

RF OUT

J12

PSM&C

Outline Drawing, 3RU S-Band SSPAwith N+1 Redundant Power Supply


8/10

Indoor Rack Mount


PAGE 8 OF 10 212463 REV C ECO 17667

Mechanical Specifications


Size (SSPA) width X height X depth 19.0 x 5.22 x 24.13483 x 133 x 613

inchesmm

Size (Power Supply) width X height X depth 19.0 x 1.75 x 15.97483 x 45 x 406

inchesmm

Weight (SSPA) Typical ( 3%)With integrated zBUC converter

75 (34)+1.7 (+0.8)

lbs. (kg)lbs. (kg)

Weight (Power Supply) with four (4) power supply modules 29 (13.2) lbs.(kg)

Finish Paint Gray; powder coat

Connectors RF InputRF Output (S-Band)RF Output (C-Band)RF Output (X-Band)RF Output (Ku-Band)

RF Output Sample

Type NType N

WR137 WaveguideWR112 WaveguideWR75 Waveguide

Type N

FemaleFemale

CPR137G Flange (PDR-70)CPR112G Flange (PDR-84)Grooved flange (PBR-120)

Female


Operating TemperatureStorage Temperature

Ambient 0 to +50-20 to +75

CC

Operating Relative Humidity Non-condensing 95 %

Cooling System Forced Convection Air Cooling Front Panel - IntakeRear Panel - Exhaust

Altitude No temperature de-rating up to 10,000 ft, (3000 m)De-rate maximum temperature by 2 C per 1,000 ft (300 m) beyond 10,000 ft.

Shock 50 g p-p, 11 msec pulses

Vibration 3g rms 30 min. 5-2000 Hz

Environmental Specifications

Audible Noise Measured 1m from unit, at Psat 71 dBA


9/10

Indoor Rack Mount


PAGE 9 OF 10 212463 REV C ECO 17667

A variety of receive band reject filters are available for S-Band amplifier. On certain models,these filters may be integrated inside the amplifier enclosure, while on others the filter willhave to be externally connected to the amplifier. Consult with the factory for details.

The filter used for frequency band 2.02 - 2.12 GHz is model L205250-S3-TX.

The filter used for frequency band 2.20 - 2.30 GHz is model L205250-S4-TX.

The filter used for frequency band 1.70 - 2.12 GHz is model L205250-S11-TX (400W max.).

X-Band GaN amplifiers may be ordered with an external receive band reject filter. The filterused for frequency band 7.90 - 8.40 GHZ is model L205250-X6-TX.

Receive Band Filter Options


10/10

Indoor Rack Mount


PAGE 10 OF 10 212463 REV C ECO 17667

HPA 3 R X G

Example - A standalone 400W Extended C-Band Rack Mount

GaN SSPA with an optional input sample port and reflectedpower monitor and no block up converter is part number:HPAC3400BRXXSVXG.

Block Up ConverterM = Internal Reference zBUCP = External Reference zBUCX = N/A

Part Number Configuration

Power Level (in Watts)S-Band

050, 100, 200, 300, 400, 500, 600C-Band

050, 100, 150, 200, 300, 400, 650,800

X-Band300, 400, 650, 800

Ku-Band040, 050, 080, 100, 150, 200, 250,300, 400, 500

PackageR = Rack Mount (Standalone)

System ConfigurationX = Standalone

See the following datasheets for system options:

Indoor Rack Mount Redundant SSPA Systems (203583)

Indoor Rack Mount Phase Combined SSPA Systems

(203584)

BandS - S-BandC - C-BandX - X-BandK - Ku-Band

Configuration Modifier 1X = StandardR = 90 Output W/G FlangeS = Input Sample PortT = 90 Output W/G Flange

& Input Sample Port

Configuration Modifier 3P = Standard (N+1 Power Supply)L = Rear Panel Exhaust Adapters

Configuration Modifier 2X = StandardV = Reflected Power Monitor

Use and Disclosure of Data

The information contained herein is classified as EAR99 under the U.S. Export Administration Regulations. Export, reexport or diversioncontrary to U.S. law is prohibited.

Specifications are subject to change without notice.

GaN Device DesignatorG = GaN Device

Rack Height3 - 3RU

Frequency Sub BandS-Band

A 2.02 to 2.12 GHzB 2.20 to 2.30 GHzG 1.75 to 2.12 GHz

C-Band

A

1

5.850 to 6.425 GHzB1 5.850 to 6.725 GHz

C 5.750 to 6.670 GHzD

1 6.425 to 7.025 GHz

H 5.715 to 5.790 GHzL 4.400 to 5.000 GHz

X-BandA

1 7.90 to 8.40 GHz

D 7.70 to 8.40 GHzF 7.10 - 7.40 GHz

Ku-BandA

1 14.00 to 14.50 GHz

B1 13.75 to 14.50 GHz

F1 12.75 to 13.25 GHz

G1 14.75 to 15.25 GHz

1Available with optional BUC

Paradise Datacom Indoor GaN 3RU SSPA 212463 RevC

Documents

Transcript of Paradise Datacom Indoor GaN 3RU SSPA 212463 RevC