Optiva OTS-1L2 3 GHz Dual Wideband Fiber Optic Links

Features

� 50 MHz to 3 GHz Optimized for IF, L- and S-Band

Satellite Signals

� 30 dB Adjustable Gain Range Provides

Perfect Level Match for Signal Distribution

� 50 & 75 Ohm BNC or 50 Ohm SMA

� Tx & Rx RF Power Monitors Via LED & Remote

� LNB Power

� SNMP Monitoring and Control

� High-Dynamic-Range, Optically-Isolated DFB

Lasers Run Cooler and Require Less Power

� Fits in Optiva Enclosures

� Hot Swap Redundant Power Supplies

Virtually Eliminate Downtime

� CE & CSA Certified, RoHS

SATCOM

626 293 3400 satcom-sales@emcore.com www.emcore.com

Optiva Dual Wideband Fiber Optic Links are optimized to perform

in the 50 MHz to 3 GHz frequency range providing transparent

signal transportation for satellite antenna applications. The OTS-1L2

is a dual RF fiber optic link that accepts two RF inputs and provides

two RF outputs with a single plug-in pair. This dual-density card

increases the chassis capacity by a factor of two.

As with all EMCORE optical products, the highest quality compo-

nents and modern production techniques insure that intra-facility links provide

the highest performance as a cost-effective alternative to coaxial cable. They

provide much longer transmission distances than copper cables, simplify network

design, ease installation and even enhance immunity from EMI, RFI and lightning.

These transmitters and receivers take the high RF performance and diverse fea-

tures of EMCORE’s Ortel technology and combine them into a compact package

compatible with the Optiva system.

satcom-sales@emcore.com www.emcore.com

PRELIMINARY DATASHEET | JUNE 2014

The Optiva platform includes a wide range fiber

optic transport products for satellite and micro-

wave communications from 1 MHz to 40 GHz. These units can be used to con-

struct transparent inter- and intra-facility links from 1 meter to >100 km for RF

and microwave signal transport, antenna remoting, video transport, electronic

warfare systems and other high-dynamic-range applications.

Optiva is a completely modular, hot-swappable platform. Both 19” rack-mount

and compact tabletop, or wall-mountable enclosures are available. The 3 RU 19”

rack-mount, fan-cooled enclosures (Model OT-CC-16 and OT-CC-16F) can support

up to 16 insert cards and utilize two dual-redundant, hot-swappable, 100 or 200

watt power supplies. The 1 RU 19” rack-mount, fan-cooled enclosure (Model: OT-

CC-6-1U) can accommodate 6 insert cards and utilizes two hot-swappable 60 watt

power supplies. Compact one-slot (OT-DTCR-1), or two-slot (OT-DTCR-2) enclosures

are also available that use an external wall-mount power supply.

System Design

© 2014 EMCORE Corporation | REV 2014.06 +1 626-293-3400

Block Diagram

Applications

� Satellite Antenna Signal Transport

� DBS Antenna Signal Distribution

� Inter-Facility Signal Transport

Performance Highlights

SATCOM

Parameter Min Typical Max Units^

Link Frequency Range 50 Ohm 75 Ohm

50 50

- -

3000 2500

MHz MHz

Fiber Distance 0 - 20 Km

Optical Loss 0 - 8 dBo

Air Temperature -10 - 50 ˚C

Isolation -60 - - dB

TX RF Input - -5 to -20 - dBm

TX Gain (TG) at max, 1 GHz** 0 8 - dB (W/A)

TG Adjustment Range (reduction from max) 30 - - dB

Noise Figure (TG at max, 2150 MHz, 1 dBo loss) - 15 -- dB

Input IP3 0 dBm

Spur Free Dynamic Range (TG at max, 1 dBo loss) - 105 - dB/Hz²/³

Wavelength 1280 - 1340

Input Return Loss 50 - 200 MHz 950 - 2150 MHz 50 MHz - 3000 MHz

10 13 8

15 18 13

- - -

dB

LNB Voltage Current

16 -

17 -

19 350

V mA

Optical Power 3 4 5 dBmo

DC Power LNB Off

- -

12 -

- 530

V mA

RX RF Output (Tx at peak, 1 dBmo into Rx) - -10 to -25 - dBm

RX Gain (RG), at max, 1 GHz2 17 19 - dB (A/W)

RG Adjustment Range (reduction from max) 10 - - dB

Output IP3 (2150 MHz) 24 25 - dBm

Output 1dB compression (2150 MHz) - 15 - dBm

Output Return Loss 50 - 200 MHz 950 - 2150 MHz 50 MHz - 3000 MHz

8 13 8

10 15 10

- - -

dB

Optical Input -12 - 10 dBmo

DC Power - -

12 -

- 340

V mA

*Lower RF inputs are acceptable.

**Link RF GaindB = TG + RG – 2*FiberLossdBo (assumes Rin = Rout)

^ dBmo & dBo indicate optical power & loss to minimize confusion with RF dBm & dB

PRELIMINARY DATASHEET | JUNE 2014

satcom-sales@emcore.com www.emcore.com

OTS-1L2

2 dB per division 3.0 GHz

.05 GHz 3.5 GHz

Typical S21

Enclosure Options

© 2014 EMCORE Corporation | REV 2014.06 +1 626-293-3400

OTS-1L2 (Tx) OTS-1LS2 (Rx)

Optiva OTS-1L2 3 GHz Dual Wideband Fiber Optic Links

satcom-sales@emcore.com www.emcore.com

SATCOM

Ordering Information

Product Code Specifications

OTS-1L2T1/B5-1306-LA-IC Tx, Dual L-band, +6 dBm, 50 Ohm BNC, LC-APC

OTS-1L2T1/S5-1306-LA-IC Tx, Dual L-band +6 dBm, 50 Ohm SMA, LC-APC

OTS-1L2T1/B7-1306-LA-IC Tx, Dual L-band +6 dBm, 75 Ohm BNC, LC-APC

OTS-1LS2R/S5-LA-IC Rx, Dual L-band, 50 Ohm BNC, LC-APC

OTS-1LS2R/B7-LA-IC Rx, Dual L-band, 50 Ohm SMA, LC-APC

OTS-1LS2R/B5-LA-IC Rx, Dual L-band, 75 Ohm BNC, LC-APC

OPV-CTLR-IC NMS SNMP Controller Card & MIB for Optiva Family

OTP-1ETR-A2/A2 Optical Tcvr, 1Ch, Ethernet, SM, Dual LC

OT-CC-16-XX Chassis, Rack-Mount, 16-Slot, 3 RU -- See OT-CC-16F data sheet for exact models

PS-200-(xx) Power Supply, 12 VDC 100 to 240 VAC, 50/60 Hz, (Specify power cord (NA, EU, UK))

OT-CC-6-XX Chassis, Rack-Mount, 6-Slot, 1 RU with Power Supply - See OT-CC-6-XX datasheet for exact models

OT-DTCR-1 / OT-DTCR-2 Chassis, Flange-Mount, w/ Power Supply, 1 slot / 2 slot - See OT-DTCR data sheet for exact models

PRELIMINARY DATASHEET | JUNE 2014

© 2014 EMCORE Corporation | REV 2014.06 +1 626-293-3400

This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser

product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class

1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products.

For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye

loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning

shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and

binoculars) may pose an eye hazard.

Wavelength = 1.3/1.5 μm.

Maximum power = 30 mW.

*Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commision.

Laser Safety

Optiva OTS-1L2 3 GHz Dual Wideband Fiber Optic Links