深圳市俊音电子有限公司 · 2019. 2. 25. · 深圳市俊音电子有限公司...
Transcript of 深圳市俊音电子有限公司 · 2019. 2. 25. · 深圳市俊音电子有限公司...
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO.,LTD.
规 格 书SPECIFICATION
客户(CLIENT):沃特沃德
客户型号(CUSTOMER MODEL): ED110A
产品名称(PRODUCT NAME):喇叭
样品型号(SAMPLE MODEL):JYL4747AO-04-8K12R
日期(DATE):2018-12-21
制造商(MANUFACTURER) 客户(CUSTOMER)盖章
(SIGENT)签名
(UNDERWRITE)日期
(DATE)盖章
(SIGENT)签名
(UNDERWRITE)日期
(DATE)
设计
(DESIGN)确认
(EVALUATED)
审核
(CHECK)审核
(CHECK)
批准(APPROVE)
批准(APPROVE)
※ 如有制造条件、部品变更等情况发生,务必由双方商定。
※ If there are manufacturing conditions, changes in parts, etc., it must be agreed by both parties.
地址:深圳市宝安区石岩上屋社区园岭志泫瀚工业园 C 栋三楼Add: Block C Of Zhixuanhan Industrial ,Shangwu Yuanling Village,shiyan,Baoan Town,ShenzhenTEL:+86-0755-29871221 29871223 FAX:+86-0755-29871230
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
内容(CONTENTS):1.电声参数和机械特征(Electrical and mechanical characteristics)
2.可靠性测试(Reliability test)
3.测试曲线(Test curve):3.1 频率响应曲线(Frequency response curve)3.2阻抗响应曲线(Impedance response curve)3.3 TS 曲线(TS curve)
4.样品测试报告(Sample Test Report)4.1频率及阻抗响应曲线(Frequency &Impedance response curve)4.2其余参数测量记录(Remaining parameter measurement records)
5.外形及包装图(Profile &Packing drawing)
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
1.电声参数和机械特征(Electrical and mechanical characteristics)
序号NO.
项目Item
规 格Specification
测定条件Conditions
1 外径External diameter 47*47±0.3mm NORMAL
2全高
Total height 29±0.3mm NORMAL
1音 圈 阻 抗
Voice coil impedance 3.6Ω ±15% AT 1000 Hz 1.0V
2最低谐振频率
Resonance frequency 160 Hz ±20% Without baffle
3频率范围
Effective frequency F0 to 20KHz -10dB
Input 1 W Value converted with 4 Ω, therange of the sound pressure level from thestandard frequency response measured at 1m from the reference point on the referenceaxis .按 4 Ω 1 W输入电压,在参考轴上距参考点
1m 处测量频响曲线。
4音 压
Sound pressure level
80 ±3 dB (LMS test)在频率点 800Hz 、1K Hz 、1.2K Hz 、
1.5K Hz或从 Hz到 Hz 计算平均声压
Average value of the sound pressurelevel at following Frequency 800 Hz、1K Hz、 1.2K Hz、 1.5KHz.
在参考轴上距参考点 1 m 处按 1 W 输入进
行测试。
Input 1W measured at 1 m from thereference point on the reference axis.
5输入功率
Input power
额定噪声功率 3WRated noise power 3W最大噪声功率 5WMax noise power 5W
见可靠性测试1
Refer Reliability test1
6动作试验
Operation test声音必需正常
The sound must be normal
Supply the sinusoidal wave 3.46 V from f0 Hzto 2k Hz.从 f0Hz到 2KHz施加正弦波电压 3.46 V。
7失真率
Distortion< 7%MAX
At 250-10KHz
输入 3.46V,在参考轴上距参考点 20 cm处测量。
Input 3.46V measured at 20cm from thereference point on the reference axis
8极性
Polarity
当把一个正的直流电流馈给扬声器正极端子时,扬声器振膜将向前运动。
When a positive DC current is applied to the plus side terminal (marked+),the diaphragmshall move forward.
9磁性材料尺寸及重量Magnet material size
&Weight
□Ferrite(铁氧体) ■NdFeB(钕铁硼)
Main(主磁):Φ17.5*5.5 Weight : / OzSub(副磁): Φ15.5*2.5 Weight : / Oz
10磁束密度
flux densityGauss or more.≥12300高斯
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
11
音圈材料及尺寸
Voice coil material &size
Material(材质): □PL □PSV □ASV ■KSVSize(尺寸):: Φ18.28*3.4Ω
12端子拉力试验
Terminal strength
将 400g 的静态拉力施加到端子上 10 秒,在任何方向端子板和盆架无损伤或松动。
A static pull of 400 g shall be applied to the terminals for 10 seconds, in any directionbetween terminal block and frame without damage or move.
13
总重量
Total weight 50.5 ±10% g
14
机械图
Mechanical drawing 见外形图 See Profile drawing
2.可靠性测试(Reliability test)序号
NO.项目
Item测定条件
Conditions规 格
Specification
1负载测试
Load test
输入3W粉红噪声信号96小时加滤波器。(输入的
电压为3.46V)Input 3 W With Pink noise Source for total 96hours with filter.
在测试结束后扬声器不能擦圈、破损、有异
音,性能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
2耐热试验
Heat test
将扬声器放入温度为 70±2℃,相对湿度为 20-35%的环境下 48小时
Put the speaker in the environment of 70±2℃and20-35% relative humidity for 48 hours.
在测试结束后扬声器不能擦圈、破损、有异
音,性能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
3耐湿试验
Humiditytest
将扬声器放入温度为30±2℃,相对湿度为90-95%的环境下48小时。
Put the speaker in the environment of 30±2℃and 90 - 95% relative humidity for 48 hours.
在测试结束后扬声器不能擦圈、破损、有异
音,性能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
4耐寒试验
Cold test
将扬声器放入温度为-25±2℃的环境下 48小时。
Put the speaker in the environment of-25±2℃for48 hours
在测试结束后扬声器不能擦圈、破损、有异
音,性能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
5盐雾测试
Salt sprayTest
测试时间:8小时;
实验环境温度: 25±5℃;环境湿度: 40~95%;
实验温度要求:盐水温度35℃,实验箱温度35℃实验盐水要求:用JIS-S-8150氯化钠溶液浓度
5±1%,其PH值为6.5-7.2;
测试后机构部分无分离、变形、表面无明显
氧化、蚀点或裂纹出现;
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
6震动测试
VibrationTest
将喇叭整箱包装后固定于振动试验台,振动48小时(振动幅度2mm);,测试后进行SPL的曲线对
比及听音测试
在测试结束后扬声器不能擦圈、破损、有异
音,性能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
7滑落测试
Slide test
将样品从1米高的60度三角架滑落,测试10次
Slide the sample from a 60-degree tripod 1 metrehigh and test it 10 times.
在测试结束后扬声器不能擦圈、有异音,性
能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
8跌落测试
Drop Test将样品在1米高位置自由跌落5次Free drop of sample 5 times at 1 m height
在测试结束后扬声器不能擦圈、有异音,性
能不能有改变
After the test the speaker shall not rub、stick or exhibit any extraneous noises andshall not have changed in performance.
3.测试曲线(Test curve)序号
NO.项目
Item内 容
Content
1频率响应曲线(Frequencyresponsecurve)
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
2
阻抗响应曲线
(Impedance
response
curve)
3 TS曲线(TS curve)
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
4.样品测试报告(Sample Test Report)
4.1频率及阻抗响应曲线(Frequency &Impedance response curve)NO. 001
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 002
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 003
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 004
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 005
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 006
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 007
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
NO. 008
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
4.2其余参数测量记录(Remaining parameter measurement records)
STANDARD F0直流电阻
DCR(20℃)
扫描测试
Sweep test
极性
Polarity
外观
Appearance全高
Total height
外径Externaldiameter
№. 160±20% Hz 3.4±7%Ω Normal Normal Normal 29±0.3 mm 47*47±0.3mm
1 165 3.6 OK OK OK 29.1 46.7*46.8
2 166 3.6 OK OK OK 29.1 46.8*46.8
3 162 3.6 OK OK OK 29 46.7*46.8
4 156 3.5 OK OK OK 29 46.7*46.7
5 165 3.6 OK OK OK 29.1 46.7*46.7
6 156 3.5 OK OK OK 28.9 46.8*46.8
7 157 3.6 OK OK OK 28.9 46.8*46.8
8 157 3.6 OK OK OK 28.9 46.8*46.8
Evaluated OK OK OK OK OK OK OK
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
5.外形及包装图(Profile &Packing drawing)
5.1外形图 Profile drawing
条形码示例图:
条形码编码规则:第 1位 J:表示俊音电子
第 2~7位 181218::表示年、月、日
第 8~12位 00001:表示喇叭流水号
4 名 称
NAMESPEAKER
单位
UNITmm
3
2 客 户
CUSTOMER公差
TOLERANCE±0.3
1
SYM 变更 REVISIONS DATE NAME机 种 名
PARTS NO.JYL4747AO-04-8K12R
比例
SCALE
批准
APPROVED审核
CHECK设计
DESIGN 外 形 图Profile drawing
三角法
TRIGONOMETRG
图号
DRAWING NO.
厚
38度
泡棉
条形码
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
5.2 包装图 Packaging drawing
每箱6层,每层36 ,总计一箱216
4 名 称
NAMESPEAKER
单位
UNITmm
3
2 客 户
CUSTOMER公差
TOLERANCE±0.3
1
SYM 变更 REVISIONS DATE NAME机 种 名
PARTS NO.JYL4747AO-04-8K12R
比例
SCALE
批准
APPROVED审核
CHECK设计
DESIGN 包 装 图Packaging drawing
三角法
TRIGONOMETRG
图号
DRAWING NO.
深圳市俊音电子有限公司SHENZHEN JUNYIN ELECTRONICS CO., LTD.
JYL4747AO-04-8K12R 材料清单
序号 物料名称 部件规格 单位 用量 供应商 备注
1 支架47*47方形正折边 双弹波台 有效高 12.5内铆 26U*中孔 19.8*内深 8.0
PCS 1 T-1
2 华司 17.9*2.5 PCS 1 T-1
3 磁钢 1 17.5*5.5 PCS 1 X-1
4 磁钢 2 15.5*2.5 PCS 1 X-1
5 鼓纸 Φ43.5 60度 18芯橡胶盆 PCS 1 Q-2
6 弹波 37*19*3.0 1.0/30g D-5 PCS 1 Q-1
7 音圈
KSV/2F 18.28*17H*3.4Ω*0.17 CCAW同向 180度 接 4股耐热铜绞线 中心距底
12PCS 1 Y-2
8 防尘帽 Φ31 纸凹帽 PCS 1 Q-2
9 端子板 YD58-03-B PCS 1 M-4
批准: 审核: 作成: