Nx Ugdocs 10.0.2.README
2
NX DOCUMENTATION VERSION 10.0.2 Windows Issued: July 2015 Files on this media are for use on 64 Bit Windows 7 and Windows 8 only. ________________________ ________________________ _________________________ ____ UPDATE INSTRUCTIONS: This media contains Maintenance Release files provided as replacements for previously installed NX 10.0 documentation. The Documentation Base release for this maintena nce release is a prer equisite to installing this update. e.g. Document ation for Version XX.Y must be installed before updating to Documentation Version XX.Y.Z Several methods are provided to perform the update: 1. Autoplay the DVD then select 'Install Documentation Update'. 2. Or, run the DVD 'launch.exe' program then select 'Install Documentation Update'. 3. Or, change dir to the nxdocs_updateXXXX folder then run 'run_nxdocs_update.exe'. The above methods will all run 'run_nxdocs_update.exe'. It then calls the nxdocs_update.bat script to apply the updates. 4. OR, you may follow the instructions below to run nxdocs_update.bat directly. Change directory to the 'nxdocs_updateXXXX' folder, then execute the 'nxdocs_update.bat' script. e.g. cd nxdocs_updateXXXX nxdocs_update.bat /v The use of UNC pathnames (e.g. \\server\path) is supported by both nxdocs_update.bat and run_nxdocs_update.exe. The script supp orts a "/v" s witch to turn on verbose messages while doing the updates. The default operation of the script is non-verbose. The script supports a "/d" switch. This will turn off all the script confirmation prompts. This is useful for running the update in a batch job. The script also supports a "/p" switch. This will turn off the initial confirmation prompt but it will display the final 'done' prompt. This is useful for running the update in a batch job where a final prompt is desired. Systems using the SPLMDocServer; If the Siemens PLM Documentation Server IS installed on the system, the update script will detect this, use a registry setting to locate the Siemens properties file and then read configuration information from the file. The documentation server should be up and running during the update so that the new Solr search indices can be uploaded. At the end of the script it will request permission to restart the server. (No request if -d switch is used). Systems NOT using the SPLMDocServer: If the Siemens PLM Documentation Server IS NOT installed on the system, such as sites using a non-Siemens doc umentation serve r. The u pdate script will
Transcript of Nx Ugdocs 10.0.2.README
7/24/2019 Nx Ugdocs 10.0.2.README
http://slidepdf.com/reader/full/nx-ugdocs-1002readme 1/2
NX DOCUMENTATION VERSION 10.0.2
Windows Issued: July 2015
Files on this media are for use on 64 Bit Windows 7 and Windows 8 only.
_____________________________________________________________________________ UPDATE INSTRUCTIONS:
This media contains Maintenance Release files provided as replacements for previously installed NX 10.0 documentation.
The Documentation Base release for this maintenance release is a prerequisite to installing this update. e.g. Documentation for Version XX.Y must beinstalled before updating to Documentation Version XX.Y.Z
Several methods are provided to perform the update:
1. Autoplay the DVD then select 'Install Documentation Update'. 2. Or, run the DVD 'launch.exe' program then select
'Install Documentation Update'. 3. Or, change dir to the nxdocs_updateXXXX folder then run
'run_nxdocs_update.exe'.
The above methods will all run 'run_nxdocs_update.exe'. It then calls the nxdocs_update.bat script to apply the updates.
4. OR, you may follow the instructions below to run nxdocs_update.batdirectly.
Change directory to the 'nxdocs_updateXXXX' folder, then executethe 'nxdocs_update.bat' script.e.g. cd nxdocs_updateXXXX
nxdocs_update.bat /v
The use of UNC pathnames (e.g. \\server\path) is supported by both
nxdocs_update.bat and run_nxdocs_update.exe.
The script supports a "/v" switch to turn on verbose messages while doing theupdates. The default operation of the script is non-verbose.
The script supports a "/d" switch. This will turn off all the scriptconfirmation prompts. This is useful for running the update in a batch job.
The script also supports a "/p" switch. This will turn off the initialconfirmation prompt but it will display the final 'done' prompt. This isuseful for running the update in a batch job where a final prompt is desired.
Systems using the SPLMDocServer;
If the Siemens PLM Documentation Server IS installed on the system, theupdate script will detect this, use a registry setting to locate the Siemens
properties file and then read configuration information from the file. Thedocumentation server should be up and running during the update so that thenew Solr search indices can be uploaded. At the end of the script it willrequest permission to restart the server. (No request if -d switch is used).
Systems NOT using the SPLMDocServer: If the Siemens PLM Documentation Server IS NOT installed on the system, such as sites using a non-Siemens documentation server. The update script will
7/24/2019 Nx Ugdocs 10.0.2.README
http://slidepdf.com/reader/full/nx-ugdocs-1002readme 2/2
prompt for the directory containing the plm_helpserver.properties file. It will then read the file for the configuration information. Your documentation server should be up and running during the update so that the new Solr search indices can be uploaded. At the end of the script it will request that youstop and restart your server.
__________________________________________________________________________
DVDROM CONTENTS:
README. - General information and installation instructions.
nxdocs_updateXXX (where XXX is the version number) - The NX Documentation update.
