Norlube 3030 MSDS

7/22/2019 Norlube 3030 MSDS

1/5

Norlube 3030 Page 1 of 5 Issue date: December 5, 2012

MATERIAL SAFETY DATA SHEET

1. Product and Company Identification

Product Name Norlube 3030

CAS # Mixture

Product Use Release agentManufacturer American Die Cast Releasants, LLC

2040 West Thompson Road

Fenton, MI. 48430

Phone 810-714-1964

Emergency Phone: 1-800-424-9300 (CHEMTREC)

2. Hazards Identification

Emergency overview

Potential short term health effects

Routes of exposure Eye, Skin contact, Inhalation, Ingestion.

Eyes May cause irritation.

Skin Frequent or prolonged contact may irritate and cause dermatitis.

Skin contact may aggravate an existing dermatitis condition.

Inhalation High vapor/aerosol concentrations (attainable at elevated temperatures well above ambient)

are irritating to the eyes and respiratory tract, and may cause headaches, dizziness,

anesthesia, drowsiness, unconsciousness, and other central nervous systems effects,

including death.

Ingestion Small amounts of this product aspirated into the respiratory system during ingestion or

vomiting may cause mild to severe pulmonary injury, possibly progressing to death.

Minimal toxicity.

Chronic effects At very high oral doses, this product caused reversible damage to the stomach, liver, and

kidney (male only) of rats. These effects are not relevant to humans at occupational levels

of exposure.

Signs and symptoms Symptoms may include redness, edema, drying, defatting and cracking of the skin.

Symptoms of overexposure may be headache, dizziness, tiredness, nausea and vomiting.

3. Composition / Information on Ingredients

Ingredient(s) CAS # Percent

No hazardous ingredients at reportable levels.

4. First Aid Measures

First aid procedures

Eye contact Flush with cool water. Remove contact lenses, if applicable, and continue flushing.

Obtain medical attention if irritation persists.

Skin contact Flush with cool water. Wash with soap and water. Obtain medical attention if irritation

persists.

Inhalation Using proper respiratory protection, immediately remove the affected victim from exposure

Administer artificial respiration if breathing is stopped. Keep at rest. Call for prompt

medical attention.

Ingestion Do not induce vomiting. Keep at rest. Call for prompt medical attention.


2/5


5. Fire Fighting Measures

Flammable properties Static discharge, material can accumulate static charges which can cause an incendiary

electrical discharge.

Suitable extinguishing media Dry chemical, CO2, water spray or alcohol resistant foam.

Protection of firefighters

Specific hazards arising from Smoke from fire may contain silicon dioxide, formaldehyde, and hydrocarbon

The chemical decomposition products; protect humans from breathing combustion products. This liquid is

volatile and gives off invisible vapors. Ether the liquid or vapors may settle in low areas or

travel some distance along the ground to surface to ignition sources where they may ignite

or explode.

Protective equipment for Firefighters should wear full protective clothing including self contained breathing

Firefighters apparatus.

6. Accidental Release Measures

Personal precautions Keep unnecessary personnel away. Do not touch or walk through spilled material. Do not

touch damaged containers of spilled material unless wearing appropriate protective

clothing. Keep people away from and upwind of spill/leak.

Methods for containment Eliminate sources of ignition. Stop leak if you can do so without risk. Prevent entry into

waterways, sewers, basements or confined areas.

Water Spill Eliminate sources of ignition. Warn occupants and shipping in surrounding and downwind

areas of fire and explosion hazard and request all to stay clear. Remove from surface of

water by skimming or with suitable adsorbents. If allowed by local authorities and

environmental agencies, sinking and/or suitable dispersants may be used in non-confined

waters. Consult and expert on disposal of recovered material and ensure conformity to local

disposal regulations

Methods for cleaning up Before attempting clean up refer to hazard data given above. Small spills may be absorbed

with non-reactive absorbent and placed in suitable, covered, labeled containers. Prevent

large spills from entering sewers of waterways. Contact emergency services and supplierfor advice. Never return spills in original containers for reuse.

7. Handling and Storage

Electrostatic Accumulation Use proper bonding and /or grounding procedure. Additional information regarding safe

Hazard handling of products with static accumulation potential can be ordered by contacting the

American Petroleum Institute.

Handling Keep container closed. Handle open container with care. Wash hands after handling and

before eating. Use good industrial hygiene practices in handling this material. Do not get

this material in your eyes, on your skin, or on your clothing.

Storage Keep out of the reach of children. Store in a closed container away from incompatible

materials in a cool, well ventilated area.

Empty containers retain product residue (liquid or vapor) and can be dangerous. Do Notpressurize, cut weld braze solder, drill, grind or expose containers to heat, flame, sparks,

static electricity, or other sources of ignition; THEY MAY EXPLODE AND CAUSE

INJURY OF DEATH. Empty drums should be completely drained, properly bunged and

promptly returned to a drum reconditioner, or properly disposed of.

8. Exposure Controls / Personal Protection


3/5


Exposure limits

Ingredient(s) Exposure Limits

Engineering Controls Use only under good ventilation conditions or with respiratory protection.

Personal protective equipment

Eye / face protection Wear safety glasses with side shields.

Hand protection Wear appropriate chemical resistant gloves.

Skin and body protection As required by employer code.

Respiratory protection Not normally required if good ventilation is maintained and exposure guidelines are not

exceeded. Where exposure guideline levels may be exceeded, use an approved NIOSH

respirator.

General hygiene considerations Handle in accordance with good industrial hygiene and safety practice. When using do not

eat or drink. Wash hands before breaks and immediately after handling the product.

9. Physical and Chemical properties

Appearance Transparent liquid.

Color White to slightly yellow.

Form Liquid.

Odor Characteristic.

Odor threshold Not available.

Physical state Liquid.

pH N/A

Freezing point -40 F.

Boiling point Approximate 400 F

Flash point 275F.

Evaporation rate 1.1 approx (n-Bu Acetate=1)

Flammability limits in air, LEL:1.4% @ 77 F. UEL: 9.3% @ 77F.

Vapor pressure 0.52mm Hg @ 68 F.

Vapor density 5.40 @ 1 atm (Air=1)

VOC (% weight) 90-98%

Specific gravity 0.98 @ 25C.

Octanol/water coefficient Not available.

Solubility (H2O) Less than 0.01% @ 77 F.

Auto-ignition temperature 441 F.

Percent volatile Less than 1%

10. Chemical Stability & Reactivity Information

Chemical stability Stable under recommended storage conditions.

Conditions to avoid Do not mix with other chemicals.

Incompatible materials Strong oxidizing agents. Acids.

Hazardous decomposition products May include and are not limited to: Oxides of carbon. Silicone dioxide. Formaldehyde

when heated to decomposition.

Possibility of hazardous reactions Hazardous polymerization does not occur.


4/5


11. Toxicological Information

Please refer to Section 3 for information on potential health effects.

12. Ecological InformationEcotoxicity Components of this product have been identified as having potential environmental

concerns.

Environmental effects Not available

Aquatic toxicity Not available

Persistency / degradability Not available

Bioaccumulation / accumulation Not available

Partition coefficient Not available

Mobility in environmental media Not available

Chemical fate information Not available

13. Disposal Considerations

Waste codes Not available

Disposal instructions Review federal, provincial, and local government requirements prior to disposal.

Waste from residues / unused Not available

ProductsContaminated packaging Not available

14. Transport Information

Department of Transportation (DOT)

Transportation of Dangerous Goods (TDG)

Not regulated as dangerous goods.

15. Regulatory Information

US Federal regulations CERCLA/SARA Hazardous Substances Not applicable.

Occupational Safety and Health Administration (OSHA)

29 CFR 1910.1200 hazardous - Yes.

CERCLA (Superfund) reportable quantity- If this product is accidentally spilled, it is not subject to any special reporting.

Superfund Amendments and Reauthorization Act of 1986 (SARA)

Hazard categories Immediate Hazard Yes

Delayed Hazard No

Fire Hazard Yes

Reactivity Hazard No

Section 302 extremely hazardous substance -No

Section 311 hazardous chemical - No

Clean Air Act (CAA) Not available

Clean Water Act (CWA) This product is classified as an oil under Section 311 of 40 CFR 110.

Safe Drinking Water Act (SDWA) Not available


5/5


Drug Enforcement Agency (DEA) Not available

Food and Drug Administration Not available

(FDA)

16. Other Information

HIMS

Health: 1 Flammability: 1 Physical Hazard: 0 Personal Protection: 2

Disclaimer Information contained herein was obtained from sources considered technically accurate

and reliable. While every effort has been made to ensure full disclosure of product hazards,

in some cases data is not available and is so stated. Since conditions of actual product use

are beyond control of the supplier, it is assumed that users of this material have been fully

trained according to the requirements of all applicable legislation and regulatory

instruments. No warranty, expressed or implied, is made and supplier will not be liable for

any losses, injuries of consequential damages which may result from the use of or reliance

on any information contained in this document.Prepared by American Die Cast Releasants, LLC (810-714-1964)

Norlube 3030 MSDS

Documents

Transcript of Norlube 3030 MSDS