Mitsubishi Camper
-
Upload
mavericknavigateur89 -
Category
Documents
-
view
228 -
download
0
Transcript of Mitsubishi Camper
-
7/27/2019 Mitsubishi Camper
1/39
Ali and Julians Travels in TardisTravels in Australia, Asia and Beyond in DIY 4wd Motorhome
Home
Convert A Canter - The Build Project November 2009 to June 2010
The aim is a self contained self sustaining go and camp almost anywhere in relative comfort vehicle.
This is a brief description of the 6-7 month build project. It was mostly achieved with just one person working almost full time, 7 days each
week. There was help along the way of course, absolutely essential for some parts. Thanks to Peter (Oka196), Ian and Dave. Always useful to
have people who can say "that's silly".
The build was made easier by the previous Coaster bus conversion. All the major bits such as solar, cooker, heater, pumps, etc. were removedfrom the Coaster and reused. The dimensions of everything were available for planning as well as the experience of having fitted them
previously.
Generally speaking it was a good project. Most things went to plan with no real surprises. A few frustrations along the way, and it of course
took longer than expected. There were also countless cups of tea, which always arrived when things weren't quite right, or the glue was about
to set. But yes, overall an essential ingredient, allowing time for thought and recovery.
The final spec is more or less ...
4wd with gross vehicle mass under 4.5mt which can be shipped in a container.
based on Mitsubishi Canter 4wd MWB 2004 FG649E
self contained and self sustaining. Diesel, fresh water, sunshine, and food in. Exhaust fumes, black and grey water, and waste packaging
out.
no gas, no normal requirement for shore power.
Layout
drop top for occasional container shipping.
central side door to reduce need for 2 people passing if door at one end.
shower / toilet / cooking at front.
comfortable seating with table at rear.
East West bed raises / lowers electrically. Two seats usable when bed down.
inner sprung, single sided, standard double bed size, mattress.
third person can use seat squab on floor for sleeping
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
1 of 39 08-12-2012 22:02
-
7/27/2019 Mitsubishi Camper
2/39
-
7/27/2019 Mitsubishi Camper
3/39
Dometic VT2500 vacuum toilet. Two 14 litre cassettes accessible externally.
Shower has tempering valve as hot water may be 80 deg C.
Separate drinking water filter.
Small cross section insulated sink. Washing dishes is probably the greatest use of water.
Having decided on a Mitsubishi Canter 4wd truck there was a bit of planning
to do. Initially I tried to draw the cab chassis in 3d from drawings available
from Mitsubishi while hunting for a suitable vehicle. However, like lots of
drawings of things to be installed, there were some critical dimensions
missing. In the end I had to wait until I bought the truck so that I could
measure it. About 3 months preparation and lead time on parts and materials.
Google Sketchup is magic - once I'd figured out how to drive it. Significant
sub-assemblies, such as the chassis, a fuel tank, the sub-frame, were drawn as
components then "assembled". Drawing is directly as 3D. Neat.
Clearly shown here is the extra fuel tank and the sub-frame with its three
point mount (pivot at rear) and 4 extra supporting springs. Apparently the
rails and supports have to be at least partially above the main chassis rails.
This is what the Engineer needed to approve and ultimately sign off.
Water tanks will fit within the sub-frame under the floor.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
3 of 39 08-12-2012 22:02
2010 06 27 htt // i l /T k Bl /2010 01 01/2010 01 01 ht
-
7/27/2019 Mitsubishi Camper
4/39
An easy way of checking the three point mount was to build a Meccano
model. It served its purpose well, demonstrating where twist would appear in
the front fixed mounts.
Basically the Canter has a relatively flexible chassis with relatively inflexiblesuspension. The chassis both twists and bends. A rectangular box body must
be decoupled from the chassis.
The pivot was placed at the rear to minimise roll of the body relative to the
ground. The pivot is also on the centre longitudinal axis of the chassis to
avoid any lateral movement of the pivot induced by chassis twist.
Some attention was given to the effect of the body on suspension geometry,particularly being aware that vehicles with beam front axles can be more
susceptible to roll steer.
A horizontal slice through the build.
The intent was to build a lightweight frameless box.
A simple layout. Shower / loo at front left. Kitchen bench at front right.
Bench seats and table at rear, to take advantage of large rear window. The
bed is transverse across the rear, electrical raise and lower (the red "legs").
This layout proved highly effective. The finished vehicle was christened
"Tardis" by some fellow motorhomers.
The internal "furniture and partitions" add to the structural strength of thebox.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
4 of 39 08-12-2012 22:02
2010 06 27 http://www epicycles com/Truck Blog/2010 01 01/2010 01 01 ht
-
7/27/2019 Mitsubishi Camper
5/39
The box over the cab was not completed. The addition of suspension seats
for both passenger and driver means the loss of access to the engine through
the cab.
In any event, the huge access to the engine from tilting the cab was too goodto give away or make more difficult.
Also, the extra weight over the cab would have made the vehicle nose heavy
and probably exceed overall design weight.
The weight is fairly evenly distributed though I would have preferred the
center of gravity to be further back. The vehicle is stable in side winds and
when passing larger trucks.
The horizontal lines below and above the windows is for the "drop top". the
section containing the windows is removable allowing the roof line to be
lower than cab height. It can be put in a 40ft HiCube container with about 2
hours effort.
The vehicle is a 2004 Mitsubishi Canter 4wd Medium Wheel Base FG649E.
The tail section of the chassis was cut off by the previous owner. Just behind
the rear spring hangers. If nothing else it provides a brilliant exit angle. It also
meant that lengthening the springs to give softer suspension was not an
option.
Driving it as a cab/chassis for 600km was bone jarring,. Even with tyre
pressures much reduced. The bouncing of the rear end translated into a foreand aft motion at head height in the cab. Turning the radio on carried the
threat of broken fingers.
The previous Coaster project, destined to supply most of the useful innards is
behind the Canter.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
5 of 39 08-12-2012 22:02
2010-06-27 http://www epicycles com/Truck Blog/2010-01-01/2010-01-01 ht
-
7/27/2019 Mitsubishi Camper
6/39
Water tanks started as large sheets of 6mm food grade polypropylene.
Sawn on a Triton Workcenter (a nice Aussie development). Essentially a very
nice saw, and later router, bench with sliding table. Set up in our garage.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
6 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
7/39
While I attacked the tanks Peter (who can weld much better than I can)
attacked the sub-frame.
The tank hangers are all lined up ready for welding to the two sub-frame
rails.
2010 06 27 http://www.epicycles.com/Truck Blog/2010 01 01/2010 01 01.ht
7 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
8/39
The tanks have been plastic welded. And tested. Its easy.
The left hand tank is divided in two. There are thus 3 fresh water tanks and
one (smallest) grey water.
There are breather outlets at the top of each tank. Inlet/outlet and tank gauge
at the bottom.
The pipes sticking out are the ends of copper pipe coiled internally for
warming in very cold weather. The glands are lengths of polypropylene round
bar with a hole for the pipe threaded for a normal olive fitting. There are no
breaks in the pipe to fail. Did I mention I have a lathe.
The value of using Sketchup really sank in here as the tanks could be built in
parallel with the sub-frame.
The completed (at this stage) sub-frame.
Its as square as we could make it (that's square and flat). The bits across theangle at the rear are bolted to allow the body to be built on the sub-frame.
The holes were cut through floor and rear after they were installed. The
bracing is hidden inside the under seat lockers.
There are additional tank hangers at the front end for a hot water calorifier.
The second fuel tank was also fitted while this sub-frame work was occuring.
Electric changeover valve.
p p y g
8 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
9/39
The bottom part of the pivot in place, just in front of the rear spring hangers.
While it can twist with the chassis its not as flexible as the existing ladder
sections and stiffens the chassis a little.
The sub-frame was rolled into place. Two people easily (!) lifted and pushed
it into place.
p p y g
9 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
10/39
Once located on the two fixed points (already bolted to the chassis) the upper
part of the pivot was installed underneath the sub-frame. With the generous
help of Ian.
And a close up of that essential rear pivot - in retrospect a few space age
holes to lighten it would have helped, and also provide a pathway for cables
and pipes.
The pin is hardened steel in a bronze bush in a polyurethane bush in a steel
tube.
The pin is held with a set screw. Unfortunately in haste the set screw wasn't
located and tightened. This led to an exciting and nervous time during the
first trip when the pin "walked" partly out and needed to be pushed back in.
No damage, but could have been very much worse. In the plan was to drill a
hole in the original rear cross member directly in line with the pin for just
such eventualities. That wasn't done until after the trip which made pushing
the pin back in a bit more awkward than it should have been.
That episode reinforced the need to investigate all strange noises or
movements as soon as they are observed.
10 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
11/39
The sub-frame is now installed. Needs welding at fixed points and pivot.
Just as attachment to the chassis rail are bolted onto the sides (there are no
breaks or holes in the top or bottom of the C section) so the sub-frame rails
are welded on the sides, not the bottom. Basic strength of materials
(recollections from Uni Metallurgy course).
11 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
12/39
The body is made of polyurethane foam fibreglass sandwich. The floor and
roof are wood batten reinforced 50mm. Walls 25mm.
The panels were drawn as 3d components in Sketchup, including drawing the
rebated joints.
It was simple to copy those components and re-assemble them as a flat sheet
from which they could be cut.
The panels are manufactured as 11m x 2.5m. Vanglas, the manufacturer, has
a very large router.
File incompatibilities got in the way but it was relatively simple to redraw for
the machine and let it cut the bits.
They arrived like some giant Ikea flatpak on the back of a small truck (easier
than me collecting them).
Here stacked against the garage wall, roughly in the sequence in which they
will be assembled.
The essence of laminates is that the strength is in the skin, the bit in the
middle is just to keep the skins apart.
12 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
13/39
Tanks in place. Phew, they fitted!. Just like the drawing said.
Also added are some external cross pieces to support and anchor the floor.
Spare wheel holder has also been added. Braces removed ready for body.
The floor.
There are four blocks of wood glued to the floor to locate it on thesub-frame.
The floor is glued to the sub-frame using Sikaflex 252. The black is the
primer for glass. The primer for steel was applied to the (unpainted) top of
the sub-frame.
13 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
14/39
Sikaflex 252. Its a lot more viscous than 11-FC used in less critical places and
required quite an effort to pump that volume from sausages.
The floor is above, waiting to be lowered. Two of the locating blocks of wood
can be seen.
Sikaflex works with large surface areas and reasonable thickness.
Under the carport (out of the sun, and later the rain).
Floor has been glued to sub-frame.
While I was happy with just Sikaflex my Engineer twisted my arm and there
are bolts (with large "washers" through brackets on those wings. At this stage
clamps were used to maintain the gap for the Sikaflex.
After 5 months of Central Australian corrugations and tracks there is no sign
of the Sikaflex giving way or of compression of the fibreglass by the through
bolts.
There's always a risk in designing and building "one-offs". The important bit
is to understand them as completely as possible before building.
Ian in the picture again.
14 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
15/39
This panel is the rear (below window level).
There is a rebate into which the floor locates.
The cuts are to fit over the main sub-frame rails.
The router cuts to within a few mm of the under side of the panel. Foam was
scraped out of the rebate with a chisel - then vacuumed up.
The rear in place. A bit of string to stop it falling over while the glue dries.
This was the first glued joint with Sikaflex 11-FC. Used rather than resin as itstays in place whereas resin tends to run, and drip, and make a mess.
We did check that the truck can be driven out of the carport after assembly.
We had a few mm to spare!
The fan is because it was hot weather.
15 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
16/39
Having learned how to glue with one joint we got ambitious and tried the
roof.
The roof is like the floor. There's a lip of the sides all the way round above
the roof so that rainwater can be collected.
Here the roof is upside down. The blocks of wood on the corners are cutout
so they don't move. The rope was tensioned by twisting.
So we successfully tried the same technique on the walls.
Some things, like exact position of the wheels, were difficult to measure to
get the drawings right. So wheel arches were cut later.
16 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
17/39
A jigsaw was used to cut the hole for the door. Don't forget the masking tape!
A nervous moment, but it worked.
The foam around the door has to be removed and wood glued in to provide
something for the door to be screwed into.
One of the problems with building a frameless fibreglass panel body is that
accessories are designed for other manufacturing techniques.
Cut out for the first hatch. This is below floor level, for the vacuum loo
cassettes.
Zed section Aluminium extrusions will be glued around the entrance.
This particular hatch really needed to allow water to flow out, so no lip. An
interesting arrangement of jack, clamps and webbing to hold it together while
gluing.
The piece removed is used for the door. The theory (and practice) is that
relatively rigid doors don't flex, the hatch doesn't breathe, and there is littledust ingress. Add a bit of rubber foam seal and everything is clean.
17 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
18/39
These hatches are access to under the seats on the passenger side. Aluminium
frame in place. The paper towels were for cleaning up the Sikaflex, with the
help of a bit of acetone.
The doors will be attached with piano hinges along the bottom and lockable
(keyed alike) compression latches at the top.
The edges of the doors will be sealed with "Kube Lok" 25mm hollow square
Aluminium slit lengthwise to be a channel. Glued with, you guessed it,
Sikaflex 11-FC.
18 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
19/39
The all important horizontal join.
Made from marine ply. The spec for marine ply is mostly about no voids and
good surface rather than glue. Both parts cut with the same router bit.
I chose a tongue and groove with angles rather than straight sides so it willcome apart more easily. One hopes!
The right of the picture is the outside.
Ply is not an engineering material. Local ply supplier humoured me and
allowed me into the warehouse with vernier calipers to select the thickness I
wanted. It would have been nice to have a pultrusion, but not practical in the
time frame for a one-off.
Made a "special tool" to dig out the foam. A chisel with a couple of bits of
steel angle bolted on so it operated like a plane that cut a deep groove.
19 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
20/39
Stood on top of the carport to take this one. Internal walls and furniture in
place. Hatches cut and framed.
Loo and cassettes installed.
Batteries are in their compartment (next to door). The vents are to allowcooling for solar regulator and battery to battery charger. That and
distribution / switchboard are separate to battery compartment which is
vented to outside.
Diesel cooker and water heater installed. Bits transferred from the Coaster.
Plumbing in place.
Foam removed ready for plywood joint.
Bench frame is "Kube Lok". 25mm hollow square aluminium with plastic
corners.
Fridge is vacuum panel insulated. Very efficient.
Space heater (bottom right) is connected to engine / diesel heater circuit.
Fridge compressor behind it.
Drawers and shower door will be made with Dibond. A sandwich of
polyethylene between 0.2mm stove enamelled Al. It can be folded by routing
a V groove. The edges can also be welded. The shower door is recoveredfrom the Coaster.
20 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
21/39
Back to the roof. It had to be turned over.
Ali and I managed that with the help of a strategically placed piece of wood.
Pity about the grass. It grew back! Not everyone has a motorhome roof on
their front lawn.
In the absence of a forklift, or similar, we opted for the old fashioned
approach. A couple of oversize tressles.
Lift the roof up Drive the truck under. Lower the roof.
Ease!
21 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
22/39
Nearly there.
And of course the ever present "will it fit?".
And of course it fits!
A good outcome. Probably the result of the combination of sufficientlydetailed drawings, the router that cut the panels, and my usual good luck.
Dave, Ian and I relaxed after a not so difficult hour.
22 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
23/39
The sides in preparation.
There's two over centre catches (from the marine store) at each corner to
hold things together during assembly.
It means one person can raise and lower the roof and attend to the sides.
The windows are standard Dometic. Double glazed acrylic. We expect to
have to polish them every so often.
The roof is raised on four legs.
Each leg is two bits of hollow square steel. A pulley at the top of the bottomleg. Hand winch at the bottom. The wire rope describes a sideways "S"
anchored to the bottom of the top bit of steel.
One turn at a time, walking round and round.
It didn't take long. Looks like we are ready for a safari.
The legs also have a long threaded rod which compresses the roof onto thewalls - a very important part of keeping the whole box rigid.
23 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
24/39
At this stage the bed legs can be installed.
Another nervous moment as they have to be inserted through the slots that
were cut in the back of the seats before they were glued in.
A real test of the drawings. Its always possible to draw things which can't beassembled.
Its also a test of whether its all going to be waterproof as there was rain
about.
All closed up. A real milestone.
24 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
25/39
And the inside beginning to look like its supposed to.
The stands for the bed legs can now be installed to get the bed to the right
height.
Bed progressing.
The wooden slats were eventually replaced with fibreglass panel, oncesatisfied that it wouldn't collapse.
The bed is standard double bed size, deliberately, which made buying a
mattress really easy.
Sketchup worked again. The bed was moved on the drawing to check the
clearances.
25 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
26/39
The four solar panels (since increased to eight for a total of a half kw) were a
bit heavy and unwieldy to lift so were slid across the gap.
The extrusion used to seal the raw foam edge around the roof is also in place.
Finding extrusions was extremely difficult. I used Kube Lok cut lengthwayson that wonderful Triton saw bench. It fitted perfectly, glued with Sikaflex.
Same was used around the bottom edge.
Finally found some pipe of the right diameter and added to the spare wheel
holders.
Hatch doors in place. Beginning to look real.
26 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
27/39
I wondered how I was going to fit the extra springs between the subframe
and chassis.
They aren't for suspension. They are there as extra load support. They are
long enough that for the small movement involved they give almost constant
support.
They were fitted by unbolting the bottom holder from the chassis, inserting
the spring, then using the centre bolt to compress the spring.
27 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
28/39
The electrical switch panel. Just to the right of the door, close to the batteries.
The switches have leds in them. The diamond shaped push button switch at
bottom right is to turn all the leds off. Phantom loads in a solar electrical
system can soon consume a lot of energy. At this stage I was one switch
short. All circuits are individually fused and there's a single large circuitbreaker close to the batteries.
The 14.2 is solar regulator volts to the batteries.
Charging is from solar and/or battery to battery charger from engine
alternator.
There is no 240v. Also no gas (diesel cooking and water heating).
28 of 39 08-12-2012 22:02
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
29/39
The wheel arch is black polyethylene sheet.
Those "wings" off the sub-frame came in useful after all. They were cleverly
positioned to give the wheel arches something to be bolted to.
29 of 39 08-12-2012 22:02
Thi i i 1 f th t Th t l i
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
30/39
This is version 1 of the steps. They are telescopic.
They worked well but tended to get stuck a bit (forgot to have something at
the top of each leg to make it telescope straight) and really needed 4 steps
instead of 3.
30 of 39 08-12-2012 22:02
Making sure the foam for the seats fits
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
31/39
Making sure the foam for the seats fits.
The foam for the squab is more resistant than that of the back.
The angles of squab and back were copied from our very comfortable settee
after much research.
Later, when showing the vehicle off, a group of 5 ladies sat and talked for a
couple of hours. I figured if it was uncomfortable they would have moved. A
good test. We've found it really comfortable.
Like lots of people I have a back problem. The seats work!
Bed with fibreglass base, finished seats, curtains, cushions.
Getting to be a real home from home.
31 of 39 08-12-2012 22:02
And looking the other way the bench and shower / loo
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
32/39
And looking the other way, the bench and shower / loo.
32 of 39 08-12-2012 22:02
There was a bit of movement in the horizontal joints on the test run
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
33/39
There was a bit of movement in the horizontal joints on the test run.
This bit of wire rope, one on each side about midway, creates tension
between the floor and the roof. It improves the rigidity of the structure,
particularly around the door.
Apparently the Sydney Opera House is also post tensioned. There are wires
through the main arches, without which it would all collapse.
Not so dramatic in our case but a well understood engineering solution.
Time to add that the legs that raise the roof also have tensioning in them to
hold the roof down and give the structure rigidity. Very important.
33 of 39 08-12-2012 22:02
And the all important spare wheel winch.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
34/39
And the all important spare wheel winch.
From an idea of Peter's. Implemented on his Oka. The wire from the brake
winch passes through the rounded pipe.
34 of 39 08-12-2012 22:02
Maiden voyage.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
35/39
y g
The tyres are the large Michelins. Later replaced with bigger rims and Toyos
after a minor hassle with engineering approval.
The build took 6-7 months.
The vehicle has a Gross Vehicle Mass (GVM) of 4495kg. This is quite useful
as in Australia it is not a heavy vehicle and in Queensland doesn't require an
annual inspection. A definite plus as the plan is to take it overseas. It can also
be driven on a car licence.
After 5 months the NextG aerial had been shaken to bits and the right hand
spare tyre holder was at risk of falling off.
This is what was left once the holder had been removed.
A bit of steel, a bit of welding, a bit of extra bracing (to stop the spare wheel
behaving like something on the end of a stalk in the wind) and it was a
relatively easy repair.
I guess something had to go wrong!
35 of 39 08-12-2012 22:02
An addition in March 2011, just before the Asia trip is two Stratos suspension
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
36/39
j p p
seats.
Turns out our friends at AllTerrainWarriors are familiar with fitting both
passenger and driver side as well as retaining that important little seat in the
middle. Important for our Chinese guide (not as it sounds, we just need threeseats).
First impression is that the vehicle travels faster, we'll have to be careful. In
the 5 months trip we weren't conscious of bottoming out the suspension
(perhaps only 4.5mt on suspension designed for 6mt).
The crawl through is a casualty of the Queensland floods which consumed
much of our time.
And after maintenance after the 5 months Aus trip, ready for the Asia trip.
The small job list was 5 pages long, including somewhere to hang a tea towel.
The new steps are still stiff. And they slide out on drawer runners rather than
being unhooked as per manufacturer's intent. The ladder arrangement under
them is for easier access when steps are up.
For the really observant there are a couple of new holes in the front bumper.
I added four recovery hooks bolted to the chassis and that was the only way
of providing access.
There are a couple of extra lockers. The water pumps and manifolds have
been moved under the floor to that new locker just to the left of the steps.
Quieter inside and out, and better priming from the tanks. Also additional
valves to allow isolation of plumbing sections in case of leaks. Left more
space for veggies inside. Also two lockers behind rear wheels under the floor.
A couple of telescopic legs behind the rear wheels.
36 of 39 08-12-2012 22:02
Round in a circle. The sides removed, bed lift dismantled, all stowed inside.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
37/39
Roof is held down by the four corner winches.
Container ready. It will be shipped to Malaysia.
Mirrors, exhaust and air inlet will be removed just before putting it in thecontainer.
The doormat goes inside!
Had a brief discussion with the one packer.
He volunteered to be inside so I handed him the radio.
Lo ratio 4wd (without the hubs engaged). Line it up from about 30m away.
There's 125mm each side. 25mm more than we thought.
The vehicle crawled so slowly that it was easy to see and correct to keep it
straight.
37 of 39 08-12-2012 22:02
It was easiest to drive it all the way in.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
38/39
A bit of a contortionist act. I'll remove the last of the mirror bracket next
time. The door is a bit curved so I had to squeeze around the front with a foot
on the bumper bar. My head just fitted under the bracket.
Perhaps I should mention I had a bit of practice in a time long ago. A bit of
potholing (speleology) and climbing.
Hopefully getting back in is as easy.
In keeping with the use of modern materials we used webbing to restrain the
vehicle. There didn't seem much point in having restraints which were too
much stronger than the lashing points in the container.
There was so much room either side I felt it unnecessary to add dunnage
bags.
38 of 39 08-12-2012 22:02
The swing lift turned up just as we'd put the seal on the door.
2010-06-27 http://www.epicycles.com/Truck Blog/2010-01-01/2010-01-01.ht
-
7/27/2019 Mitsubishi Camper
39/39
Much better than a forklift!
More to follow when we take it out of the container in Malaysia.
Brisbane to Guy Fawkes River National Park Week 1 - June 27th 2010
39 of 39 08-12-2012 22:02