M-Series Pattern Design Software FIN computerized flat knitting machine m-100/132/172sjt/203sjt...

M-SERIES

COMPUTERIZED FLAT KNITTING MACHINE M-100/132/172SJT/203SJT

PATTERN DESIGN SOFTWARE

MATSUYA

2012.02.25

機械 (惠州) 有限公司 MATSUYA MACHINERY (HUIZHOU) CO., LTD

Operation Manual

Sep 打版软件功能说明书_2012-02 of 8

CONTENT

1. SETTING ………………………………………………………………………………… 3 - 4 2. MAIN DISPLAY…………………………………………………………………………… 5 3. BASIC MENU……………………………………………………………………………… 6 4. EXPLANATION OF DATA NAME IN MAIN DISPLAY … …………………………… 7

PAGE


Operation Manual


Microsoft Office Excel 2003 SETTING START THE SOFTWARE SemiProgEdit_ver110218.xls AS SHOWN BELOW

NOTE：THIS SOFTWARE IS APPLICABLE ONLY FOR Microsoft Office Excel 2003

“MACRO SAFETY” WILL POP UP FOR THE FIRST TIME TO OPEN THIS SOFTWARE

CLICK“TOOL”→ “MACRO” →“SAFETY”


Operation Manual


AT “MACRO” SELECT THE SAFETY LEVEL TO “LOW” AND THEN CLICK “SET”


Operation Manual


Microsoft Office Excel 2007 OR 2010 SETTING

AFTER SETTING THE “MACRO”, RE-START“SemiProgEdit_ver110218.xls”SOFTWARE THIS TIME THE “MACRO” WINDOW WILL NOT POP UP.

START THE SOFTWARE SemiProgEdit_ver110218.xlsm AS SHOWN BELOW

NOTE：THIS SOFTWARE IS APPLICABLE ONLY FOR Microsoft Office Excel 2007 OR 2010

“MACRO SAFETY” WILL POP UP FOR THE FIRST TIME TO OPEN THIS SOFTWARE Click the yellow bar“ Enable Content”, then can use the software.


Operation Manual


MAIN DISPLAY

BASIC MENU：BASIC COMMAND AS (LOAD)、(SAVE)、(ERROR CHECK)、(INSERT)、(DELETE) DATA NAME：INCLUDING (LEFT CARRIAGE)、(RIGHT CARRIAGE)、FRONT STITCH［ST(F)］、 REAR STITCH［ST(B)］、FRONT CAM［CAM(F)］、REAR CAM［CAM(B)］、YARN FEEDER (YARN)、 RACKING (RACK)、CARRIAGE SPEED (SPD)、CARRIAGE STROKE (STRK)、 JUMP (JUMP)、 TAKE-DOWN（TAKE DOWN）、END PATTERN（END）. CARRIAGE DIRECTION (DIR)：CARRIAGE DIRECTION (“→”LEFT TO RIGHT“←”RIGHT TO LEFT). COURSE OF PATTERN：THE AREA INDICATING THE PATTERN COURSE NO. PATTERN DATA：THE AREA INDICATING THE DATA FOR THE PATTERN.

BASIC MENU

DATA NAME

PATTERN DATA

CARRIAGE DIRECTION

COURSE OF

PATTERN


Operation Manual


BASIC MENU

KEY FOR LOADING THE PATTERN TO LOAD THE PATTERN. (FORMAT ：*.csv)

KEY FOR SAVING THE PATTERN TO SAVE THE PATTERN. (FORMAT：*.csv)

KEY FOR ERROR CHECK TO CHECK THE PATTERN DATA WHETHER THERE IS ERROR. WHEN THERE IS ERROR ON CERTAIN DATA, IT WILL TUEN TO “RED” COLOR

KEY FOR INSERT THE AREA TO BE INSERTED IS THE SPECIFIED DATA AT “Start” AND THE SPECIFIED NO. OF COURSE AT “Lines”. EX: INPUT 2 TO “Start” AND INPUT 4 TO “Lines”AND THEN PRESS “INSERT” KEY. THIS INDICATES INSERT 4 COURSES BEFORE THE SECOND (2ND) COURSE.

KEY FOR DELETE THE AREA TO BE DELETED IS THE SPECIFIED DATA FROM “Start” TO “End”


Operation Manual


EXPLANATION OF DATA NAME

DATA FOR LEFT CARRIAGE

DATA FOR RIGHT CARRIAGE

WHEN USING ONLY ONE CARRIAGE, INPUT THE DATA “0” TO THE OTHER CARRIAGE

DATA FOR FRONT STITCH（RANGE 0～182）

DATA FOR FRONT CAM（5-DIGIT NO. , USE ONLY THE NUMBER 0、1、2）

DATA FOR REAR STITCH（RANGE 0～182）

DATA FOR REAR CAM（5-DIGIT NO. , USE ONLY THE NUMBER 0、1、2）

DATA FOR YARN FEEDER (TOTAL 6 YARN FEEDERS. EX: “24” MEANS NO. 2 AND NO. 4 YARN FEEDER. (COMBINATION OF 11, 22, 33, 44, 55, 66 IS NOT POSSIBLE)

DATA FOR RACKING（DATA TO BE 1、12、2、23、3、34……7、78、8， ORIGIN TO BE 45）

DATA FOR CARRIAGE SPEED（DATA FROM 1 TO 9）

DATA FOR CARRIAGE STROKE（DATA TO BE 1、2、3、4、5.） “3” TO BE THE MAX. STROKE. “1”& ”2”IS FIRST GROUP OF SMALL STROKE, “4” & “5”IS SECOND GROUP OF SMALL STROKE

THE COURSE TO START JUMP

THE COURSE TO END JUMP

JUMP DATA

NO. OF JUMP

DATA FOR TAKE-DOWN. IT IS DIVIDED INTO 9 STEPS (1-9)

KEY TO END PATTERN. SET “1” TO END THE PATTERN. IF NOT, SET ”0”.

M-Series Pattern Design Software FIN computerized flat knitting machine m-100/132/172sjt/203sjt...

Documents

Transcript of M-Series Pattern Design Software FIN computerized flat knitting machine m-100/132/172sjt/203sjt...