Low Speed High Torque Hydraulic Motors XCEL CH and · PDF fileXCEL CH and CS Series European...
Transcript of Low Speed High Torque Hydraulic Motors XCEL CH and · PDF fileXCEL CH and CS Series European...
Low Speed High Torque Hydraulic MotorsXCEL CH and CS Series European Preferred Products
EATON Low Speed High Torque Hydraulic MotorsXCEL CH and CS Series E-MOOV-CC001-E1 June 20132
Features Proven orbit motor principle Hydrodynamic journal bearings Three moving components (gerotor-star, drive, and shaft) Three zone pressure design Optimized drive running angle Variety of displacements and shafts Designed for medium and low duty
Benefits Compact, powerful package High efficiency Design flexibility Economically tailored solutions Long bearing life (at rated loads)
Applications Aerial work platform Augers Conveyors Food processing Harvesters Machine tools Spreaders Turf care equipment Winches
XCEL spool valve motors distribute pressurized fluid into and out of the orbit gear set via valve slots integrated into the output shaft. The spool valve motors incorporate both valv-ing and hydrodynamic journal bearings into a common shaft design. These motors incorporate the proven orbit motor
principle to provide high torque at low speeds. Motor shaft ro-tation can be instantly reversed by changing direction of input/output flow while generating equal torque in either direction. The displacements available provide a wide variety of speeds and torque.
CS motor feature Eatons Geroler technology to minimize friction and increase operating efficiency, whilst internal check valves limit case pressure to that of the outlet port.
Specifications CS Motor
Geroler Element 9 DisplacementsFlow L/min 57 Continuous*** 68 Intermittent** Speed RPM up to 875 RPM inter. **Pressure bar 138 Cont.*** 155 Inter.** Torque Nm 473Cont.*** 512 Inter.**
***Continuous-(Cont.) Continuous rating, motor may be run continuously at these ratings. **Intermittent-(Inter.) Intermittent operation,10%of every minute.
Specifications CH Motor
Geroler Element 11 Displacements Flow L/min 57 Continuous*** 68 Intermittent** Speed rpm Up to 800 rpm inter. ** Pressure bar 124 Cont.*** 138 Inter.** Torque Nm 426 Cont.*** 507 Inter.**
XCEL Spool Valve MotorsProduct Description, Features Benefits and Applications
EATON Low Speed High Torque Hydraulic MotorsXCEL CH Series E-MOLO-MR001-E November 2009 3
Features
Proven orbit motor principle
Hydrodynamic journal bearings
Three moving components (gerotor-star, drive, and shaft)
Three zone pressure design
Optimized drive running angle
Variety of displacements and shafts
Designed for medium and low duty
Benefits
Compact, powerful package
High efficiency
Design flexibility
Economically tailored solutions
Long bearing life (at rated loads)
Applications
Aerial work platform
Augers
Conveyors
Food processing
Harvesters
Machine tools
Spreaders
Turf care equipment
Winches
Many more
Gerotor Element 11 DisplacementsFlow L/min 57 Continuous*** 68 Intermittent**Speed rpm Up to 800 rpm inter. **Pressure bar 124 Cont.*** 138 Inter.**Torque Nm 426 Cont.*** 507 Inter.***** Continuous-(Cont.) Continuous rating, motor may be run continuously
at these ratings.** Intermittent-(Inter.) Intermittent operation,10%of every minute.
Product Description
XCEL spool valve motors distribute pressurized fluid into and out of the orbit gear set via valve slots integrated into the output shaft. The spool valve motors incorporate both valving and hydrodynamic journal bearings into a common shaft design. These motors incorporate the proven orbit motor principle to provide high torque at low speeds. Motor shaft rotation can be instantly reversed by changing direction of input/output flow while generating equal torque in either direction. The displacements available provide a wide variety of speeds and torque.
Port APort B
Output ShaftDrive
Gerotor
Specifications
XCEL Spool Valve MotorsProduct Description, FeaturesBenefits and Applications
Geroter
EATON Low Speed High Torque Hydraulic MotorsXCEL CH and CS Series E-MOOV-CC001-E1 June 2013 3
XCEL Spool Valve Motors XCEL CH Series (016-)Specification Data
A simultaneous maximum torque and maximum speed NOT recommended.
To assure best motor life, run motor for approximately 1 hour at 30% of rated pressure before application to full load.
Be sure motor is filled with fluid prior to any load applica- tions.
Recommended fluids: premium quality, anti-wear type hydraulic oil.
Minimum oil viscosity (at operating temperature): Never below 13cSt best viscosity range 20-32cSt for Geroler.
Recommended maximum system operating temp.:82C.
Recommended filtration: Per ISO Cleanliness Code 4406, level 20/18/13.
Maximum inlet pressure: 150 bar without regard to bar and /or back pressure ratings or combination thereof.
4 EATON Low Speed High Torque Hydraulic MotorsXCEL CH Series E-MOLO-MR001-E November 2009
XCEL Spool Valve Motors Specification Data
A simultaneous maximum torque and maximum speed NOT recommended.
To assure best motor life, run motor for approximately 1 hour at 30% of rated pressure before application to full load.
Be sure motor is filled with fluid prior to any load applications.
Recommended fluids: premium quality, anti-wear type hydraulic oil.
Minimum oil viscosity (at operating temperature): Never below 20 cSt best viscosity range 20-32 cSt. Recommended maximum system operating temp. 82C.
Recommended filtration: Per ISO cleanliness code 4406, level 20/18/13.
Maximum inlet pressure: 150 bar without regard to bar and / or back pressure ratings or combination thereof.
Cap Screws Static Seal Housing Drive Cap Screws Spacer Gerotor
End Cap Case DrainBearing RaceThrustBearing
PressureSeal
OutputShaft
Static SealsExclusionSeal
View of Gerotor Section
Displacement cc/r 53 63 80 100 125 160 200 245 315 390 485
FlowLPM
Continuous 38 45 57 57 57 57 57 57 57 57 57Intermittent 45 53 68 68 68 68 68 68 68 68 68
Max. Speed(RPM)
Continuous 721 693 710 568 462 354 286 234 174 144 114Intermittent 864 806 848 678 551 421 341 282 209 171 138
PressureBar
Continuous 124 124 124 124 124 115 110 100 90 83 69Intermittent 138 138 138 138 138 124 124 124 124 110 90
TorqueNm
Continuous 83 104 130 162 200 242 287 318 377 419 426Intermittent 93 116 145 181 223 260 324 391 508 547 507
Weight kg 5 5.3 5.5 6.1 6.2 6.4 6.7 7.1 7.4 7.7 8
View of Geroter Section
Displacement cc/r 53 63 80 100 125 160 200 245 315 390 485
Flow Continuous 38 45 57 57 57 57 57 57 57 57 57 LPM Intermittent 45 53 68 68 68 68 68 68 68 68 68
Max. Speed Continuous 721 693 710 568 462 354 286 234 174 144 114 (RPM) Intermittent 864 806 848 678 551 421 341 282 209 171 138
Pressure Continuous 124 124 124 124 124 115 110 100 90 83 69 Bar Intermittent 138 138 138 138 138 124 124 124 124 110 90
Torque Continuous 83 104 130 162 200 242 287 318 377 419 426 Nm Intermittent 93 116 145 181 223 260 324 391 508 547 507
Weight kg 5 5.3 5.5 6.1 6.2 6.4 6.7 7.1 7.4 7.7 8
EATON Low Speed High Torque Hydraulic MotorsXCEL CH and CS Series E-MOOV-CC001-E1 June 20134
Motors run with high efficiency in all areas designated with a number for torque and speed, however for best motor life select a motor to run with a torque and speed range printed in the light shaded area. Performance data is typical at 25 cSt. Actual data may vary slightly from unit to unit in production.
Continuous
Intermittent
ContinuousMax. Cont. Int.
28 41 55 69 83 97 110 124 138
Flo
w L
PM
7.622
11233
10945
10557
1006994
8188
15.122
22732
22444
21957
21469
20881
20292
195104187
116178
22.721
34432
34043
33656
33068
32380
31791
310104302
116294
30.320
46631
46443
46055
45568
45080
44490
438103430
114421
37.919
58130
57842
57354
56867
56279
55490
549102542
114536
Max. Cont. 45.4
28693
39691
52684
65680
77675
89667
101650
113652
Int. 53.437
80650
80262
79675
79187
78498
776111769
CH-63(63.6cm3/r) Pressure Bar
CH-53(52.2cm3/r) Pressure Bar
ContinuousMax. Cont.
Int.
28 41 55 69 83 97 110 124 138
Flo
w L
PM
7.618
13927
13436
12845
12155
11265
102
15.117
28226
27736
27045
26355
25564
24674
23683
22493
209
22.716
42825
42235
41445
40655
39765
38674
37683
36593
353
30.314
57523
57033
56243
55453
54663
53672
52582
51292
498
Max. Cont. 37.9
14721
23719
33714
43708
53702
62692
71682
81670
91659
Int. 45.422
86431
86041
85251
84461
81670
82680
81590
804
22 Torque nm 864 Speed rpm
ContinuousMax. Cont.
Int.
28 41 55 69 83 97 110 124 138
Flo
w L
PM
7.62892
4289
5785
7180
8674
10168
11462
15.128
18541
18256
17871
17386
168101162
115155
130147
145183
22.726
27640
2775