LINEARANTRIEBE KATALOG - Mecvel srl · Serie Stückzahl: Anwendungsbeschreibung: Arbeitsumfeld...
Transcript of LINEARANTRIEBE KATALOG - Mecvel srl · Serie Stückzahl: Anwendungsbeschreibung: Arbeitsumfeld...
LINEARANTRIEBE KATALOG
1 - Version 2018
Index - MecVel lInearantrIebe Katalog
Intro 2
ProduKt KonfIguratIonsforMular 5
alI1 - Max belastung: 1.200 n 7
alI2 - Max belastung: 2.500 n 11
alI3 - Max belastung: 6.000 n 17
alI4 - Max belastung: 10.000 n 23
alI5 - Max belastung: 18.000 n 29
aV3 - Max belastung: 25.000 n 33
ec - Max belastung: 50.000 n 37
reIhe hrs - Max belastung: 200.000 n 43
l - Max belastung: 5.000 n 49
oPtIonen 53
VerKaufsbedIngungen 68
2 - Version 2018
InTRO
Allgemeines zu HubzylindernElektromechanische Hubzylinder sind mehrstufige Getriebe bestehend aus einem Elektro-motor, einem Getriebe und einem Spindel-Mutter-System. Die Rotation des Motors (Ge-triebemotors) wird durch das Spindel-Mutter-System in lineare Bewegung umgesetzt. Die Last darf lediglich axial wirken. Querkräfte auf die Kolbenstange sind zu vermeiden. Dabei ist es egal, ob die Last ziehend oder drückend zu bewältigen ist.Die wesentliche Funktion von elektromechanischen Hubzylindern ist: Relativ große Kräfte (hängt von der Größe des Hubzylinders ab) mit relativ langsamer Geschwindigkeit zu be-wegen.
HauptbestandteileElektromotor• Getriebe• Spindel-Mutter-System• Kolbenstange•
ElektromotorDie in diesem Katalog bezeichneten Motoren sind Standard IEC AC-Motoren. Drehstrom-oder Einphasenwechselstrommotoren mit oder ohne Federkraftbremse.
Mögliche Extras „Sonderwunsch“ für die Standardreihe ACMotoren UL/CSA• Motoren Tropenisoliert• Motoren mit ATEX Zone 22 Kat. 3B• Motoren in Sonderspannungen• Bremsmotoren mit Handlüftung• Hubzylinder mit 2. Schneckenwellenende• Hubzylinder mit mehr als 2 Endschaltern• Hubzylinder mit Kugelumlaufspindeln•
Die in diesem Katalog bezeichneten Motoren sind mit DC-Permanentmagnetmotoren ausgerüstet.
Mögliche Extras „Sonderwunsch“ für die Standardreihe DCWeitere DC Spannungen• Bremsmotoren• Hubzylinder mit 2. Schneckenwellenende• Hubzylinder mit mehr als 2 Endschaltern• Hubzylinder mit Kugelumlaufspindeln•
GetriebeDie in diesem Katalog bezeichneten Hubzylinder sind mit Schneckengetrieben ausgestat-tet.
3 - Version 2018
Spindel-Mutter-SystemKaltgerollte Profile bei Trapezgewindespindeln, gepaart mit weichen Muttern z.B. aus Bron-ze.
KolbenstangeDie Kolbenstangen sind aus verchromtem Stahl gefertigt.
Alle Hubzylinder werden nach ISO 9000 gefertigt und sind CE zertifiziert.Sie werden grundsätzlich kundenspezifisch produziert, damit sichergestellt ist, daß genau das geliefert wird, was der Kunde benötigt.
AuswahlkriterienDie Hauptkriterien zur Auswahl von Hubzylindern sind:
Hubkraft• Hubgeschwindigkeit• Einschaltdauer• Umgebungsbedingungen•
Hubkraft und HubgeschwindigkeitDie beiden Parameter sind umgekehrt proportional zueinander. Das heißt, je höher die Hubgeschwindigkeit, umso kleiner die Hubkraft (bei gleicher Leistung des Motors).Es ist sehr wichtig, den Kraft- und Geschwindigkeitsverlauf über die gesamte Hublänge zu kennen, um eventuell zusätzlich auftretende Kräfte basierend auf Massenträgheitsmo-menten zu berücksichtigen.
Einschaltdauer und UmgebungsbedingungenDiese Parameter müssen immer zusammen betrachtet werden.Die Einschaltdauer der im Katalog aufgeführten Hubzylinder beträgt 30% bezogen auf 5 min.Die Umgebungsbedingungen beziehen sich auf die Umgebungstemperaturen bzw. auf Störgrößen wie Wasser, aggressive Flüssigkeiten, Staub etc.Die Einschaltdauer S3 – 30% / 5min bezieht sich auf eine Umgebungstemperatur von 30°C.Der zulässige Arbeitstemperaturbereich für die Standardtypen liegt zwischen -10°C und +60°C.
SelbsthemmungDie Größe Selbsthemmung ist relativ. Sie hängt vom Wirkungsgrad des Zylinders, der Um-gebung (z.B. Vibration ) und dem Verschleiß ab. Ein Zylinder, der anfangs noch selbsthem-mend ist, kann unter gewissen Umständen nach längerer Laufzeit die Selbsthemmung verlieren.
Mechanische EndlagenschalterDie einstellbaren Schaltnocken, welche die Microschalter betätigen, sind in der Regel sehr genau. Die Signale werden dann über Schützen oder Relais ausgewer-tet.
4 - Version 2018
Einbauempfehlungen des HubzylindersDie Hubzylinder sollten durch qualifiziertes Personal eingebaut werden• Der elektrische Anschluss muss durch qualifiziertes Personal erfolgen• Es ist darauf zu achten, dass der Kontakt mit der Spannungsversorgung bei der Monta-• ge Vor der Inbetriebnahme ist unbedingt darauf zu achten, daß das Endschaltersystem • (integriert oder extern) korrekt eingestellt und angeschlossen ist
Schon in der Konstruktionsphase ist es sehr wichtig, korrekte Befestigungspunkte vorzu-sehen, sodass keine radialen Kräfte auf die Kolbenstange oder den gesamten Zylinder einwirken können. Beim Einbau in die Maschine ist dieses nochmals zu überprüfen.Während der Konstruktion sollte weiterhin darauf geachtet werden, nicht zu klein zu di-mensionieren.Die einfache Regel ist, die nächst größere angegebene Hublänge zu wählen. Das verein-facht die Schaltvor-gänge, und verhindert das Fahren auf den „inneren Block“. Das Fah-ren auf den „inneren Block“ zerstört die Mechanik des Hubzylinders.
Elektromechanische Linearantriebe haben unzählige Anwendungen in der Maschinen-, Anlagen- und Prozess-Industrie.
Mit großem Erfolg werden diese Hubzylinder bereits in den Bereichen wie:Landmaschinentechnik• Siloanlagen• Fütterungsanlagen• Medizintechnik• Rehatechnik• Verfahrenstechnik• Lebensmitteltechnik• Großküchenmaschinen• Fleischereimaschinen• Bäckereitechnik• Verpackungsmaschinen• Werkzeugmaschinen• Förderanlagen• Holzbearbeitungsmaschinen• Apparatebau allgemein• Meß- und Prüftechnik• Fahrzeugbau• Fahrzeugumbau• Schiffsbau• Architektur• Gebäudetechnik• Eventanlagen•
Sollten aber zusätzliche technische Einzelheiten für die Applikation benötigt werden, bitte einfach anfragen.
5 - Version 2018
Produkt konfigurationsformular
ProduktkonfigurationHubzylinder AC
Hubzylinder DC
Einzelstück
Serie Stückzahl:
Anwendungsbeschreibung:
Arbeitsumfeld (Temperaturbereich, Luftfeuchtigkeit):
Kraft
Mittlere Kraft (N):
Maximale Kraft (N):
Zugkraft
Kompressionskraft
Kraft in beide Richtungen
GeschwindigkeitMittlere Geschwindigkeit (mm/s):
Maximale Geschwindigkeit (mm/s):Hub (mm):
motor
Kein Motor
AC Stromversorgung (V):
DC Stromversorgung (V):
Schrittmotor
Servo
Bremse
Ohne
Mit
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
6 - Version 2018
Gewinde
Trapezgewinde
Kugelumlaufspindeln
Einbaulage
Horizontal
Vertikal/Aufwärts
Vertikal/Abwärts
Schwenksystem
Kraft Position
Vorwärts
Rückwärts
Beides
Einschaltdauer
Zyklen/Minute:Zyklen/Tag:Stunden/Tag:Tage/Jahr:Pausenzeit zwischen Zyklen (Sekunden):
Optionen
Endschalter
Potentiometer
Encoder
Hinteres Ende
Vorderes Ende
Verdrehsicherung
Drehmomentbegrenzer
Sicherheitsmutter
Balg
Speziallackierung
Für Kundenspezifische Lösungen wenden sie sich bitte direkt an [email protected].
7 - Version 2018
ALI
1
LINEARANTRIEBE ALI1
Max Belastung: 1.200 NMax Geschwindigkeit: 90 mm/s
DC
TECHNISCHE DATEN ALI1
Motor mit Permanentmagnet 12, 24 VDC•Schneckengetriebe•Trapezgewinde•Aluminium Schubstange (Auf Wunsch rostfrei)•Dauerschmierung mit Fett•IP 65•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter und Inkrementalgeber auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
8 - Version 2018
ALI
1
LEISTUNGEN ALI1
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motordrehzahl (rpm)
95 90 M12 40S 6300190 90 M13 40L 6000130 60 M10 40S 6300270 60 M11 40L 6000200 45 M07 40S 6300400 45 M09 40L 6000290 30 M04 40S 6300580 30 M06 40L 6000500 15 M01 40S 6300
1200 15 M03 40L 6000
12 VDC Motor - Stromaufnahme verdoppelt sich und Drehzahl sinkt um 20%•
ABMESSUNGEN ALI1 UND ALI1-F MIT ENDSCHALTER
6039
A
B10
63
46
18
57
10
19.5
Ø20
57
36.5
36
7
12
6.5
Ø43
Ø56
136.
5 (D
)
120.
5 (C
)
Ø18 14
39
Ø8 + 0.2 0
Ø6 + 0.1 0
Ø8 + 0.2 0
Maß Hub < 240 mm Hub > 240 mmA 53,5 + Hub 66,5 + HubB 90 + Hub 103 + HubC 40S = Kurzer MotorD 40L = Langer Motor
9 - Version 2018
ALI
1
ELEKTRISCHE VERDRAHTUNG
Die Endschalter sind mit einem Sprungkontakt als Umschalter ausgestattet. Signale, für Geschwindigkeiten von mehr als 30 mm/s benötigen zur richtigen Erfassung Hochlei-stungskontakte. Anschluss C02 und C06 schalten den Motorstromkreis direkt. Es muss gewährleistet sein, dass die beiden Endschalter nicht überfahren werden können. Die Sel-bsthemmung der Spindel muss so groß sein, dass diese innerhalb des Schaltbereiches des Endschalters zum Stillstand kommt. Damit kommt diese Schaltung nur bei langsam laufen-den Schubstangen zum Einsatz, oder wenn permanent entgegenwirkende Kräfte vorhan-den sind. Falls dies nicht zutreffend ist, wird eine Relaisschaltung oder PLC Schaltung, siehe C03 und C07) notwendig.
MOTORLAGE
Der Motor kann an beiden Seiten des Antriebs montiert werden, siehe Zeichnungen (An-trieb von hinten ge sehen).
BRAUN
BLAU
BRAUNBLAU
OUT 1
OUT 2
ROTHELLBLAUORANGEGRÜN
1 2
4
2 14
BRAUNBLAU
OUT 1
OUT 2
ROTHELLBLAUORANGEGRÜN
1 2
4
2 14
SCHWARZWEISSGELBPINK
ROTHELLBLAUORANGEGRÜN
OUT 1
OUT 2
BRAUNBLAU
1 2
4
2 14
BRAUNBLAU
1 2
4
2 14
SCHWARZGRÜNWEISSGELBGRAUPINKBRAUNBLAU
1 2
4
2 14
SCHWARZWEISSGRÜNGRAUGELBPINKBRAUNBLAU
2 14
Spindeldrehrichtung bei Stromanschluss + auf blauem Draht
C01/C02/C03/C04/C05C06/C07 Kabellänge 500 mm
C08/C09/C10/C11/C12C13/C14 Kabellänge 2500 mm
C01C08
C02C09
C03C10
C04C11
C05C12
C06C13
C07C14
Motoranschluss 2 Endschalter2 Endschalter mit Schutzdiode
3 Endschalter
Inkrementalgeber 2 Endschaltermit Schutzdiode
+ Inkrementalgeber
2 Endschalter+ Inkrementalgeber
M1 = SXM0 = DX
10 - Version 2018
ALI
1
KOLBENSTANGENENDE
Abmessung „B“ variiert je nach ModellALI1: Hub > 240 mm + 13 mm•ALI1-F: Hub > 240 mm + 13 mm•
BESTELLSCHLüSSEL
MODELLALI1 ALI1-F
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHwINDIGKEIT (mm/s)M01/M03/M04/M06/M07/M09/M10/M11/M12/M13 M00: Sondergeschwindigkeit
MOTOR12: 12 VDc 24: 24 VDC
MOTORLAGEM0: rechts M1: links
ELEKTRISCHE VERDRAHTUNGC01/C08 C02/C09C03/C10 C04/C11C05/C12 C06/C13C07/C14 C00 (Sonderverdrahtung)
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VORDERES ENDEA2: Geschlitztes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M8
OpTIONEN (Siehe letztes Kapitel)
ALI1/0250/M01/12/M0/C01/C08/p1/A2/
B = 141 + Hub
Ø8 +0.2 0 Ø8 H7
Ø24
Ø20
14 46
129
B = 95 + Hub10
Ø8 +0.2 0
14
Ø20
Ø18
M8
20
B = 90 + Hub
Ø8 +0.2 0
Ø20
Ø6 +0.1 0
Ø18
710
9
16
12
6.5
B = 137 + Hu 10b
Ø8 +0.2 0 Ø8 h8
16Ø20
14 42
16
8
A4 = GELENKAUGE A 7 = AUSSENGEWINDE M8A2 = GESCHLITZTES ENDE [STANDARD)
1010 12
A3 = GABELKOPF
11 - Version 2018
ALI
2TECHNISCHE DATEN ALI2
1- und 3-Phasen-Motor•Permanent-Gleichstrommotor 12, 24 VDC•Schneckengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett•Schutzart IP 54 für AC-Version (IP 65 auf Anfrage)•Schutzart IP 65 für DC-Version•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter und Inkrementalgeber auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE ALI2
Max Belastung: 2.500 NMax Geschwindigkeit: 110 mm/s
AC/DC
12 - Version 2018
ALI
2
LEISTUNGEN ALI2
ALI2 24 VDC
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
800 110 M08 59 - 3000850 70 M09 59 - 3000
1100 55 M10 59 - 30001500 40 M11 59 - 30002000 30 M12 59 - 30002500 20 M13 59 - 30002500 10 M14 59 - 3000
ALI2 3-PHASEN-MOTOR 400 VAC
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
450 110 M01 IEC50 0,09 2800500 70 M02 IEC50 0,09 2800650 50 M03 IEC50 0,09 2800850 40 M04 IEC50 0,09 2800
1000 30 M05 IEC50 0,06 14001400 20 M06 IEC50 0,06 14002200 10 M07 IEC50 0,06 14002500 5 M08 IEC50 0,06 1400
ALI2 VRS 3-PHASEN-MOTOR 400 VAC
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
1500 45 M01 IEC50 0,09 28001800 30 M02 IEC50 0,09 28002000 20 M03 IEC50 0,06 14002500 10 M04 IEC50 0,06 14002500 5 M05 IEC50 0,06 1400
1-Phasen-Motor 230 VAC – Performance um 20% reduziert•12 VDC Motor - Stromaufnahme verdoppelt sich und Drehzahl sinkt um 20%•
Ø10+0.1 0
Ø25
Ø36
43
B + Hub
45
13 10
79.5
66.513
21.5
52.5 33
.5 20 20
41.5
55
74
19
21.5
153.
5
Ø10+0.1 0
Ø59A + Hub
13 - Version 2018
ALI
2
ABMESSUNGEN ALI2 VDC
ABMESSUNGEN ALI2 VAC
Maß Hub < 320 mm Hub > 320 mmA 70 + Hub 80 + HubB 115 + Hub 125 + Hub
Maß Hub < 320 mm Hub > 320 mmA 70 + Hub 80 + HubB 115 + Hub 125 + Hub
ALI2 VRS = + 40 mm
Ø10+0.1 0Ø10
+0.1 0
4513 10
21.5
182.
5
204
94
Ø25
Ø36
20
20
13
55
43
79.5
66.5
41.5
3272
Ø104129
38
242
Bre
msm
otor
21.5
33.5
147 Bremsmotor 119 Bremsmotor
A + HubB + Hub
Ø10+0.1 0
Ø25
Ø36
43
B + Hub
45
13 10
79.5
66.513
21.5
52.5 33
.5 20 20
41.5
55
74
19
21.5
153.
5
Ø10+0.1 0
Ø59A + Hub
14 - Version 2018
ALI
2
ABMESSUNGEN ALI2-F VDC MIT ENDSCHALTER
ABMESSUNGEN ALI2-F VAC MIT ENDSCHALTER
Maß Hub < 320 mm Hub > 320 mmA 70 + Hub 80 + HubB 138 + Hub 148 + Hub
Maß Hub < 320 mm Hub > 320 mmA 70 + Hub 80 + HubB 138 + Hub 148 + Hub
ALI2-F VRS = + 63 mm
Ø25
10
Ø10+0.1 0
90
20
68
Ø10+0.1 0
43
13
Ø36
94
182.
5
55
41.5
13
129
72
103
20
7651
32
249.
5
Ø104119 Bremsmotor
38
287.
5 Br
emsm
otor
45.5
21.5
6721
.533
.5
147 Bremsmotor
A + HubB + Hub
90
102.5
13
20
20
33.5
52.5
21.5
1368 A + Hub
B + Hub 10
Ø10+0.1 0
43
67
Ø10+0.1 0
Ø25
Ø36
76 7455 1951
41.5
132
153.
5
21 46
Ø59
15 - Version 2018
ALI
2
MOTORLAGE
KOLBENSTANGENENDE
Abmessung „B“ variiert je nach ModellALI2: Hub > 320 + 10 mm•ALI2-F: + 23 mm, Hub > 320 mm + 33 mm•ALI2-FCM: + 34 mm, Hub > 320 mm + 44 mm•ALI2 VRS Hub > 320 mm + 40 mm•ALI2-F VRS Hub > 320 + 63 mm•Mit Passfedernut G + 30 mm•Mit Balg B + 20 mm•
P2P1M0
1 FC1
A1 = RUNDES ENDE (STANDARD)
B = 115 + Hub13
Ø10 +0.1 0
Ø25Ø10
+0.1 0
10 B = 178 + Hub
Ø10 +0.1 0
13
2020
12
2010
Ø10 H8
B = 125 + Hub13
Ø10 +0.1 0
32
Ch.1
9
M10
A3 = GABELKOPF
A7 = AUSSENGEWINDE M10
13
Ø10 H7 Ø30
10.5 14
15B = 182 + Hub
Ø10 +0.1 0
A4 = GEKENKAUGE
HINTERES ENDEKLEMMKASTENLAGE GEHäUSE ENDSCHALTER POSITION
16 - Version 2018
ALI
2
BESTELLSCHLüSSEL
MODELLALI2 ALI2-FALI2 VRS ALI2-F VRSALI2-FCM ALI2-FCM VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)DC-Version M08/M09/M10/M11/M12/M13/M14 AC-Version M01/M02/M03/M04/M05 M06/M07/M08/M09/M10
MOTORAC: Version/Spannung/Type/Größe/Drehzahl/Leistung DC: Version/Spannung/Größe/Drehzahl
MOTOROPTIONEN
MOTORLAGEKeine: Freilassen M0
KLEMMKASTENLAGEKeine: Freilassen 1
ENCODERKeine: Freilassen
ENDSCHALTER Keine: Freilassen
POTENTIOMETERKeine: Freilassen POT01A (1Kohm) POT10A (10Kohm)
ENDSCHALTER POSITIONKeine: Freilassen FC1
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VORDERES ENDEA1: Rundes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M10
OPTIONEN (Siehe letztes Kapitel)
ALI2/0250/M01/AC-400/50-T-56-4-0,09/AB/M0/1/E06/2FC1/P0T01A/FC1/P1/A1/
17 - Version 2018
ALI
3TECHNISCHE DATEN ALI3
1- und 3-Phasen-Motor•Permanent-Gleichstrommotor 12, 24 VDC•Schneckengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett•Schutzart IP 54 für AC-Version (IP 65 auf Anfrage)•Schutzart IP 65 für DC-Version•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter und Inkrementalgeber auf Anfrage•ATEX II 3 D T4 AC-Motor auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE ALI3
Max Belastung: 6.000 NMax Geschwindigkeit: 35 mm/s
AC/DC
18 - Version 2018
ALI
3
LEISTUNGEN ALI3
ALI3 24 VDC
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
3600 35 M01 59 - 50003600 25 M02 59 - 50006000 12 M03 59 - 50006000 9 M04 59 - 50006000 5 M05 59 - 5000
ALI3 3-PHASEN-MOTOR 400 VAC
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
2600 20 M01 IEC56 0,14 28002800 14 M02 IEC56 0,14 28004800 7 M03 IEC56 0,14 28005000 5 M04 IEC50 0,09 28005000 2,5 M05 IEC50 0,09 2800
ALI3 VRS 3-PHASEN-MOTOR 400 VAC
Kraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
5000 9 M01 IEC50 0,09 28005000 3,5 M02 IEC50 0,09 2800
1-Phasen-Motor 230 VAC – Performance um 20% reduziert•12 VDC Motor - Stromaufnahme verdoppelt sich und Drehzahl sinkt um 20%•
19 - Version 2018
ALI
3
ABMESSUNGEN ALI3 VDC
ABMESSUNGEN ALI3 VAC
Maß Hub < 320 mm Hub > 320 mmA 69 + Hub 79 + HubB 112 + Hub 122 + Hub
Baugröße AC-MotorVersion H K Ø P
50 Standard 188 110 105Bremsmotor 226
56 Standard 216 110 108Bremsmotor 260
KH33
.5
318333.5
Ø67
Ø36
1631
5722
727
38
Ø10+0.1 0
Ø25
10B + Hub15
43 A + Hub
Ø10
H11
Ø30
ØP
47.5
22 57
1543
Ø77
A + Hub B + Hub
Ø30
Ø10
H11 Ø36
Ø10+0.1 0
Ø67
33.5 69.5
31
103
152
186.
5
33.5
Ø25
81.516
31
72738
10
20 - Version 2018
ALI
3
ABMESSUNGEN ALI3-F VDC MIT ENDSCHALTER
ABMESSUNGEN ALI3-F VAC MIT ENDSCHALTER
Maß Hub < 320 mm Hub > 320 mmA 69 + Hub 79 + HubB 144 + Hub 154 + Hub
Baugröße AC-MotorVersion H K Ø P
50 Standard 188 110 105Bremsmotor 226
56 Standard 216 110 108Bremsmotor 260
Ø36
7616
22 89
7
27
38
Ø10+0.1 0
Ø25
1015
75
Ø30
Ø10 H11
187.
5
K
31
33.5
51Ø67
31
33.5 83
84
ØP
B + Hub
A + HubH
33.5
Ø10 H11 7633
.5
Ø30
15
75 A + Hub
B + Hub 10
186.
5
152
Ø77
50
Ø10+0.1 0
84
22 89
16
31113.5
Ø36
38
27
31
103
117.5
33.5 69.5
Ø67
Ø25
51
7
21 - Version 2018
ALI
3
MOTORLAGE
KOLBENSTANGENENDE
Abmessung „B“ variiert je nach ModellALI3: Hub > 320 + 10 mm•ALI3-F: + 32 mm, Hub > 320 mm + 42 mm•ALI3-FCM: + 36 mm, Hub > 320 mm + 46 mm•ALI3 VRS Hub > 320 mm + 40 mm•ALI3-F VRS Hub > 320 + 63 mm•Mit Passfedernut G + 30 mm•Mit Balg B + 20 mm•
M0
1
FC1
P1 P2
B = 112 + Hub
16
27
Ø10 H11
15
20
30
10
Ø25Ø10
+0.1 0
107
10
A1 = RUNDES ENDE (STANDARD)
B = 175 + Hub
27
15
16
Ø10 H11
20
53
Ø10 h8
30
11
20201010
107
A3 = GABELKOPF
B = 179 + Hub
16
15
27
Ø10 H11
15
14
10.5
57
Ø30Ø10 H7
1010
7
30
A4 = GEKENKAUGE
16
B = 122 + Hub15
27
Ø10 H11
32
M10
30
1010
7
A7 = AUSSENGEWINDE M10
SW19
HINTERES ENDEKLEMMKASTENLAGE GEHäUSE ENDSCHALTER POSITION
22 - Version 2018
ALI
3
BESTELLSCHLüSSEL
MODELLALI3 ALI3-FALI3 VRS ALI3-F VRSALI3-FCM ALI3-FCM VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)DC-Version M01/M02/M03/M04/M05 AC-Version M01/M02/M03/M04/M05
MOTORAC: Version/Spannung/Type/Größe/Drehzahl/Leistung DC: Version/Spannung/Größe/Drehzahl
MOTOROPTIONEN
MOTORLAGEKeine: Freilassen M0
KLEMMKASTENLAGEKeine: Freilassen 1
ENCODERKeine: Freilassen
ENDSCHALTER Keine: Freilassen
POTENTIOMETERKeine: Freilassen POT01A (1Kohm) POT10A (10Kohm)
ENDSCHALTER POSITIONKeine: Freilassen FC1
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VORDERES ENDEA1: Rundes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M10
OPTIONEN (Siehe letztes Kapitel)
ALI3/0250/M01/AC-400/50-T-56-4-0,09/AB/M0/1/E06/2FC1/P0T01A/FC1/P1/A1/
23 - Version 2018
ALI
4TECHNISCHE DATEN ALI4
1- und 3-Phasen-Motor•Permanent-Gleichstrommotor 12, 24 VDC•Schneckengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett•Schutzart IP 54 für AC-Version (IP 65 auf Anfrage)•Schutzart IP 65 für DC-Version•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter, Inkrementalgeber und Sonderausführungen auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE ALI4
Max Belastung: 10.000 NMax Geschwindigkeit: 100 mm/s
AC/DC
24 - Version 2018
ALI
4
LEISTUNGEN ALI4
ALI4 24 VDCKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
600 100 M20 85 - 30001100 50 M21 85 - 30002800 20 M22 85 - 30004100 13 M23 85 - 30006800 7 M24 85 - 3000
10000 4 M25 85 - 3000
ALI4 VRS 24 VDCKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
2400 63 M26 85 - 30003400 25 M27 85 - 30003900 16 M28 85 - 30006800 8 M29 85 - 30007500 5 M30 85 - 3000
ALI4 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
2100 93 M01 IEC71 0,55 28003900 47 M02 IEC71 0,55 28005300 23 M03 IEC63 0,37 14008600 9 M04 IEC63 0,22 14009400 6 M05 IEC63 0,18 1400
10000 3 M06 IEC63 0,13 140010000 2 M07 IEC56 0,09 1400
ALI4 VRS 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
2500 58 M08 IEC63 0,25 28003100 29 M09 IEC63 0,18 14003400 23 M10 IEC56 0,14 28005000 15 M11 IEC56 0,14 28006000 7 M12 IEC56 0,09 14007500 4 M13 IEC56 0,09 1400
1-Phasen-Motor 230 VAC – Performance um 20% reduziert•12 VDC Motor - Stromaufnahme verdoppelt sich und Drehzahl sinkt um 20%•
25 - Version 2018
ALI
4
ABMESSUNGEN ALI4 VDC
ABMESSUNGEN ALI4 VAC
Baugröße AC-MotorVersion H K Ø P
56 Standard 168 116 108Bremsmotor 200
63 Standard 190 129 110Bremsmotor 235
71 Standard 220 146 121Bremsmotor 267
160 + Hub107 + Hub
1453
88
12 55.575
25
Ø30
Ø30
10385
1832
91.5
52
Ø12+0.1 0
Ø12+0.1 0
Ø50
Ø85
39.5
155
14
Ø30
53 107 + Hub12160 + Hub
Ø12
853218
103
26.7
30
55.5
52
75.2
25
Ø50
P
Ø12
Ø
Ø30
39.5
91.5
HK
+0.1 0
+0.1
0
26 - Version 2018
ALI
4
A3 = GABELKOPF
B = 223 + Hub
B = 160 + Hub
Ø12+0.1 0Ø12
+0.1 0
A1 = RUNDES ENDE (STANDARD)
14
32
Ø30
32
Ø30
Ø12 H8
24
61
14
12 24
Ø12+0.1 0
Ø30
B = 162 + Hub
A4 = GELENKAUGE
Ø12+0.1 0
A7 = AUSSENGEWINDE M12
Ø30
32
14 34
Ø30
B = 225 + Hub
Ø12 H7
63
Ø12+0.1 0
Ø30
32
17
1612
14
1214
M12
ABMESSUNGEN ALI4-F VDC MIT ENDSCHALTER
ABMESSUNGEN ALI4-F VAC MIT ENDSCHALTER
Ø50
12
107 + Hub83
Ø30
P
14 190 + Hub
133115
18
32
2690
1243
Ø30
8426
Ø12
52
765525
44
Ø
39.5
91.5
HK
+0.1
0
+0.1 0
Baugröße AC-MotorVersion H K Ø P
56 Standard 168 116 108Bremsmotor 200
63 Standard 190 129 110Bremsmotor 235
71 Standard 220 146 121Bremsmotor 267
Ø30
43
5239
.5
91.5
2547
90120.5
Ø85
155
12
Ø50
88
190 + Hub
107+ Hub83
14
18
32 133115
Ø12+0.1 0 83.9
Ø30
Ø12+0.1 0
27 - Version 2018
ALI
4
A3 = GABELKOPF
B = 223 + Hub
B = 160 + Hub
Ø12+0.1 0Ø12
+0.1 0
A1 = RUNDES ENDE (STANDARD)
14
32
Ø30
32
Ø30
Ø12 H8
24
61
14
12 24
Ø12+0.1 0
Ø30
B = 162 + Hub
A4 = GELENKAUGE
Ø12+0.1 0
A7 = AUSSENGEWINDE M12
Ø30
32
14 34
Ø30
B = 225 + Hub
Ø12 H7
63
Ø12+0.1 0
Ø30
32
17
1612
14
1214
M12
MOTORLAGE
KOLBENSTANGENENDE
Abmessung „B“ variiert je nach ModellALI4-F: + 30 mm•ALI4-FCM: + 42,5 mm•ALI4 VRS: + 25 mm•ALI4-F VRS: + 55 mm•ALI4-FCM VRS: + 53 mm•Mit Passfedernut G + 30 mm•Mit Balg B + 15 mm•
HINTERES ENDEKLEMMKASTENLAGE GEHäUSE ENDSCHALTER POSITION
P1 P2M0 1 FC1
28 - Version 2018
ALI
4
BESTELLSCHLüSSEL
MODELLALI4 ALI4-FALI4 VRS ALI4-F VRSALI4-FCM ALI4-FCM VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)DC-Version AC-Version
MOTORAC: Version/Spannung/Type/Größe/Drehzahl/Leistung DC: Version/Spannung/Größe/Drehzahl
MOTOROPTIONEN
MOTORLAGEKeine: Freilassen M0
KLEMMKASTENLAGEKeine: Freilassen 1
ENCODERKeine: Freilassen
ENDSCHALTER Keine: Freilassen
POTENTIOMETERKeine: Freilassen POT01A (1Kohm) POT10A (10Kohm)
ENDSCHALTER POSITIONKeine: Freilassen FC1
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VORDERES ENDEA1: Rundes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M12
OPTIONEN (Siehe letztes Kapitel)
ALI4/0250/M01/AC-400/50-T-56-4-0,09/AB/M0/1/E06/2FC2/P0T01A/FC1/P1/A1/
29 - Version 2018
ALI
5TECHNISCHE DATEN ALI5
1- und 3-Phasen-Motor•Schneckengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett und öl•Schutzart IP 54 für Bremsmotor (IP 65 auf Anfrage)•Schutzart IP 65 für AC-Version•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter, Inkrementalgeber und Sonderausführungen auf Anfrage•ATEX II 3 D T4 AC-Motor auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE ALI5
Max Belastung: 18.000 NMax Geschwindigkeit: 93 mm/s
AC
30 - Version 2018
ALI
5
LEISTUNGEN ALI5
ALI5 3-PHASEN-MOTOR 400 VACKraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
4300 93 M01 IEC80 1,1 28007200 47 M02 IEC80 1,1 2800
11000 23 M03 IEC71 0,75 28009000 12 M04 IEC71 0,55 1400
18000 6 M05 IEC71 0,37 140018000 3 M06 IEC71 0,37 1400
ALI5 VRS 3-PHASEN-MOTOR 400 VACKraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
4800 93 M45 IEC71 0,55 28006000 47 M46 IEC71 0,37 28007500 23 M47 IEC71 0,37 28009500 12 M48 IEC71 0,25 1400
12000 6 M49 IEC71 0,25 1400
1-Phasen-Motor 230 VAC – Performance um 20% reduziert•
ABMESSUNGEN ALI5 VAC
109
24
25118 164 + Hub
Ø70
110
50.5
208
282 + Hub 68.340
218
124 55
69
266
Brem
smot
or
Ø141
Ø40
Ø20+0.1 0
27
Ø20 +0.1 0
31 - Version 2018
ALI
5
24
25 27
Ø70
B = 282 + Hub
Ø40
24
25
40
M20
x1.5
B = 362 + Hub
24
25 44
Ch.3
6
Ø70
M20
x1.5
B = 265 + Hub
Ø40
24
25 B = 359 + Hub
2040
25 25
18 25 0 -0
.1
Ø20 H7Ø20+0.1 0 Ø20
+0.1 0
Ø20+0.1 0
Ø20 h8Ø20+0.1 0 Ø20
+0.1 0
40 Ø50
M20
x1.5
ABMESSUNGEN ALI5-F VAC MIT ENDSCHALTER
MOTORLAGE UND GEHäUSE ENDSCHALTER POSITION
KOLBENSTANGENENDE
Abmessung „B“ variiert je nach ModellALI5/ALI5-F: Hub > 500 + 20 mm•ALI5-FCM: Hub < 500 +40 mm, Hub > 500 + 60 mm•ALI5 VRS/ALI5-F VRS: Hub < 500 + 88 mm, Hub > 500 + 108 mm•ALI5-FCM VRS: Hub < 500 + 128 mm, Hub > 500 + 148 mm•Mit Passfedernut G + 50 mm, Mit Balg B + 25 mm•
109
24
25
118 164 + Hub
Ø70
114
50.5
208
282 + Hub 68.340
218
124 55
69
266
Brem
smot
or
Ø141
Ø40
Ø20+0.1 0
27
Ø20+0.1 0
HINTERES ENDEKLEMMKASTENLAGE
M0 - FC1 M1 - FC2
P1 P2
1
32 - Version 2018
ALI
5
BESTELLSCHLüSSEL
MODELLALI5 ALI5-FALI5 VRS ALI5-F VRSALI5-FCM ALI5-FCM VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)AC-VersionPAM: RPM
MOTORAC: Version/Spannung/Type/Größe/Drehzahl/Leistung PAM: 0
MOTOROPTIONEN
MOTORLAGEKeine: Freilassen M0 - FC1 M1-FC2
KLEMMKASTENLAGEKeine: Freilassen 1
ENCODERKeine: Freilassen
ENDSCHALTER Keine: Freilassen
POTENTIOMETERKeine: Freilassen POT01A (1Kohm) POT10A (10Kohm)
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VORDERES ENDEA1: Rundes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M20
OPTIONEN (Siehe letztes Kapitel)
ALI5/0250/M01/AC-400/50-T-56-4-0,09/AB/M0-FC1/1/E06/2FC2/P0T01A/P1/A1/
33 - Version 2018
AV3
TECHNISCHE DATEN AV3
1- und 3-Phasen-Motor B14•Schneckengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett •Schutzart IP 54 für Bremsmotor (IP 65 auf Anfrage)•Schutzart IP 65 für AC-Version•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter, Inkrementalgeber und Sonderausführungen auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE AV3
Max Belastung: 25.000 NMax Geschwindigkeit: 55 mm/s
AC
34 - Version 2018
AV3
LEISTUNGEN AV3
AV3 3-PHASEN-MOTOR 400 VACKraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
13000 55 M01 IEC90 3 280020000 30 M02 IEC90 3 280025000 20 M03 IEC80 1,80 280025000 10 M04 IEC80 1,10 140025000 5 M05 IEC80 0,75 1400
AV3 VRS 3-PHASEN-MOTOR 400 VACKraft (N)
Geschw. (mm/s)
Ausführung Bauart Motorleistung (kW)
Motordrehzahl (rpm)
8000 45 M01 IEC80 0,75 280013000 22 M02 IEC80 0,55 140025000 15 M03 IEC80 0,75 280025000 7 M04 IEC80 0,55 1400
1-Phasen-Motor 230 VAC – Performance um 20% reduziert•
ABMESSUNGEN AV3 VAC MIT ENDSCHALTER
Baugröße AC-MotorVersion H K Ø P
80 Standard 238 165 220Bremsmotor 296
90 Standard 280 182 251Bremsmotor 344
Ø20 +0.1 0
25
Ø20 +0.1 0
188
86
43
4854
285 + Hub
116.5
Ø40
18
Ø65
P
168.5 + Hub 450
10013
6.5
31.5
K
H
Ø45
Ø
46
40
5352
114.5
128.
510
2
35 - Version 2018
AV3
MOTORLAGE UND GEHäUSE ENDSCHALTER POSITION
KOLBENSTANGENENDE
Abmessung „B“ variiert je nach ModellAV3 VRS: + 40 mm•Mit Passfedernut G + 50 mm•Mit Balg B + 25 mm•
HINTERES ENDEKLEMMKASTENLAGE
1M1-FC1 P1 P2
B = 364 + Hub
Ø40
Ø20+0.1 0
18
Ø20 H7
25 0 -0
.1
18
25
B = 285 + Hub
Ø20+0.1 0
18
Ø40
Ø45
Ø20+0.1 0
25
B = 270 + Hub
Ø20+0.1 0
18
Ø40
M20
x1.5
44
B = 367 + Hub
Ø20+0.1 0
18
Ø40 40
40
20
40
Ø20
25
A4 = GELENKAUGE
A1 = RUNDES ENDE (STANDARD)
A7 = AUSSENGEWINDE M20
A3 = GABELKOPF
36 - Version 2018
AV3
BESTELLSCHLüSSEL
MODELLAV3AV3 VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)AC-VersionPAM: RPM
MOTORAC: Version/Spannung/Type/Größe/Drehzahl/Leistung PAM: 0
MOTOROPTIONEN
MOTORLAGEKeine: Freilassen M1 - FC1
KLEMMKASTENLAGEKeine: Freilassen 1
ENCODERKeine: Freilassen
ENDSCHALTER Keine: Freilassen
POTENTIOMETERKeine: Freilassen POT01A (1Kohm) POT10A (10Kohm)
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VORDERES ENDEA1: Rundes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M20
OPTIONEN (Siehe letztes Kapitel)
AV3/0250/M01/AC-400/50-T-56-4-0,09/AB/M0-FC1/1/E06/2FC2/P0T01A/P1/A1/
37 - Version 2018
ECTECHNISCHE DATEN EC
1- und 3-Phasen-Motor B14•Planetengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett •Schutzart IP 54 für Bremsmotor (IP 65 auf Anfrage)•Schutzart IP 65 für AC-Version•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Integrierte Endschalter•Inkrementalgeber und Sonderausführungen auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE EC
Max Belastung: 50.000 NMax Geschwindigkeit: 230 mm/s
AC
38 - Version 2018
EC
LEISTUNGEN EC
EC1 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
500 193 M01 IEC63 0,37 28001250 97 M02 IEC71 0,37 14002000 60 M03 IEC71 0,37 9005000 24 M04 IEC71 0,55 14005000 15 M05 IEC71 0,25 9005000 6 M06 IEC63 0,13 1400
EC1 VRS 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
500 230 M01 IEC63 0,18 28001250 115 M02 IEC63 0,18 14002000 75 M03 IEC71 0,25 9005000 30 M04 IEC63 0,18 14005000 19 M05 IEC71 0,18 9005000 7 M06 IEC63 0,13 1400
EC2 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
1000 193 M01 IEC80 0,75 28002500 97 M02 IEC80 0,75 14002500 60 M03 IEC80 0,55 900
10000 24 M04 IEC80 1,1 140010000 15 M05 IEC80 0,55 90010000 6 M06 IEC71 0,25 1400
EC2 VRS 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
1250 230 M01 IEC71 0,37 14002500 150 M02 IEC80 0,55 9005000 60 M03 IEC71 0,37 1400
10000 35 M04 IEC80 0,55 90010000 15 M05 IEC63 0,18 1400
1-Phasen-Motor 230 VAC – Performance um 20% reduziert•
39 - Version 2018
EC
EC3 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
2500 193 M01 IEC90 2,20 28005000 97 M02 IEC90 1,80 14005000 60 M03 IEC90 1,50 900
15000 24 M04 IEC90 1,80 140015000 15 M05 IEC90 1,10 90015000 6 M06 IEC71 0,37 1400
EC3 VRS 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
3000 230 M01 IEC80 0,75 14003000 150 M02 IEC80 0,55 900
10000 60 M03 IEC80 0,75 140015000 35 M04 IEC80 0,55 90015000 15 M05 IEC71 0,25 1400
EC4 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
15000 56 M01 IEC112 2,20 90025000 42 M02 IEC100 4 140030000 25 M03 IEC112 3 90030000 10 M04 IEC90 1,50 1400
EC4 VRS 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
25000 60 M01 IEC90 1,80 140030000 35 M02 IEC100 1,50 90030000 15 M03 IEC90 1,10 1400
EC5 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
50000 11 M01 IEC100 3 140050000 7 M02 IEC100 2,20 900
EC5 VRS 3-PHASEN-MOTOR 400 VACKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
50000 15 M01 IEC90 1,10 140050000 10 M02 IEC90 0,75 900
40 - Version 2018
EC
ABMESSUNGEN EC1 EC2 EC3
Baugröße AC-MotorVersion H Ø P
63Standard 185
123 110Bremsmotor 234
71Standard 215
140 121Bremsmotor 267
80Standard 238
159 138Bremsmotor 296
90Standard 255
176 149Bremsmotor 319
a3
95a4
Øg1
H
P
c1
b2 b3c3
c4
c2
a1
a2
b1
g2
112
g3
Vorderes Ende A7
Kugelumlaufspindel (VRS)
a1 (Hub = 0)
a2 (Hub = 0)
a3 (Laut AC-Version) a4 b1
Øh7 b2 b3 c1 c2 c3 c4 g1 g2 g3 (Laut AC-Version)
EC1 169 135 - 61 Ø14 105 145 M10 Ø30 Ø50 30 50 103 -EC2 233 189 - 66 Ø20 140 200 M12 Ø50 Ø70 35 65 118 -EC3 317 262 - 75 Ø30 190 270 M18 Ø60 Ø85 45 80 138 -
Trapezgewinde
a1 (Hub = 0)
a2 (Hub = 0)
a3 (Laut AC-Version) a4 b1
Øh7 b2 b3 c1 c2 c3 c4 g1 g2 g3 (Laut AC-Version)
EC1 145 111 - 61 Ø14 105 145 M10 Ø30 Ø50 34 50 103 -EC2 167 123 - 66 Ø20 140 200 M12 Ø50 Ø70 44 65 118 -EC3 255 200 - 75 Ø30 190 270 M18 Ø60 Ø85 55 80 138 -
AC-VersionM01 M02 M03 M04 M05 M06
EC1a3 147 157 157 157 157 172g3 131 141 141 141 141 156
EC1-VRSa3 147 147 157 147 157 172g3 131 131 141 131 141 156
EC2a3 182 182 182 182 182 201g3 158 158 158 158 158 177
EC2-VRSa3 169 182 169 182 201 -g3 145 158 145 158 177 -
EC3a3 200 200 200 200 200 226g3 173 173 173 173 173 199
EC3-VRSa3 188 188 188 188 226 -g3 161 161 161 161 199 -
41 - Version 2018
EC
ABMESSUNGEN EC4 EC5
Baugröße AC-MotorVersion H Ø P
90Standard 255
176 149Bremsmotor 319
100Standard 309
195 173Bremsmotor 374
112Standard 328
219 192Bremsmotor 407
Kugelumlaufspindel (VRS)
a1 (Hub = 0)
a2 (Hub = 0)
a3 (Laut AC-Version) a4 b1
Øh7 b2 b3 c1 c2 c3 c4 g1 g2 g3 (Laut AC-Version)
EC4 318 259 - 79,5 40 200 300 M30X2 80 120 60 80 136 -EC5 318 259 - 79,5 40 200 300 M30X2 80 120 60 80 136 -
Trapezgewinde
a1 (Hub = 0)
a2 (Hub = 0)
a3 (Laut AC-Version) a4 b1
Øh7 b2 b3 c1 c2 c3 c4 g1 g2 g3 (Laut AC-Version)
EC4 272 212 - 79,5 40 200 300 M30X2 80 120 60 80 136 -EC5 272 212 - 79,5 40 200 300 M30X2 80 120 60 80 136 -
AC-VersionM01 M02 M03 M04
EC4a3 246,5 246,5 246,5 238,5g3 218 218 218 210
EC4-VRSa3 200,5 246,5 238,5 -g3 172 218 210 -
EC5a3 284,5 284,5 - -g3 256 256 - -
EC5-VRSa3 238,5 238,5 - -g3 210 210 - -
a3
95a4
Øg1
H
P
c1
b2 b3
c3c2
a1
b1
g2
a2
112
g3
Vorderes Ende A7
c4
42 - Version 2018
EC
VORDERES ENDE
BESTELLSCHLüSSEL
MODELLEC1 EC2 EC3 EC4 EC5EC1-VRS EC2-VRS EC3-VRS EC4-VRS EC5-VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)AC-VersionPAM: RPM
MOTORAC: Version/Spannung/Type/Größe/Drehzahl/LeistungPAM: 0
MOTOROPTIONEN
ENCODERKeine: Freilassen
ENDSCHALTER Keine: Freilassen
POTENTIOMETERKeine: Freilassen POT01A (1Kohm) POT10A (10Kohm)
VORDERES ENDEA3: Gabelkopf A4: Gelenkauge A7: Außengewinde
OPTIONEN (Siehe letztes Kapitel)
EC1/0250/M01/AC-400/50-T-56-4-0,09/AB/E06/2FC2/P0T01A/A3/
Abmessungen A3a1 a1-VRS a2 a3 a4 a5 a6 a8 a9 a10
EC1 172 196 14 Ø12 M12 12 61 24 24 24EC2 220 286 25 Ø20 M20X1,5 20 97 40 40 40EC3 317 379 35 Ø25 M24X2 25 117 50 50 50
EC4 EC5 345 392 38 Ø30 M27X2 30 131 54 55 55
Abmessungen A4b1 b1-VRS b2 b3 b4 b5 b6 b7 b9
EC1 174 198 16 Ø12 M12 12 16 63 32EC2 217 283 25 Ø20 M20X1,5 18 25 94 50EC3 313 375 30 Ø25 M24X2 22 31 113 60
EC4 EC5 345 392 35 Ø30 M27X2 25 37 131 70
b1 + Hub b2
b3
b7
b6b4
b9b5
a1 + Hub a2
a3 a10
a6
a5 a9
a8
a4
43 - Version 2018
HRS
TECHNISCHE DATEN HRS
Speziell konzipiert für Heavy-Duty und Aussenanwendungen•Lasten bis max. 200 kN•Hubgeschwindigkeiten bis max. 65 mm/s•Geringe Reibung und Verschleiss•Lange Lebensdauer•Minimale Geräuschentwicklung•DieSerieistkundenspezifischinTrapezspindel-(TPN)oderKugelumlaufspindelau-•sführung(VRS)lieferbar
DerStandardaufbaudesSpindelhubelementsistoptimalaufdieLinearaktuator-Kompo-nenten abgestimmt. Angefangen bei einer Reihe von Innenführungen bis hin zum exter-nenAbdeckrohr,welchesspeziellzumSchutzundzurbesserenUnterstützungbeimKni-cken vorgesehen sind.
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
REIHE HRS
Max Belastung: 200.000 NMax Geschwindigkeit: 65 mm/s
AC
44 - Version 2018
HRS
LEISTUNGEN HRS50 TPNKraft (N)
Geschw. (mm/s)
Au-sführung
Bauart Motorlei-stung (kW)
Motor-drehzahl
(rpm)
Überset-zung
Gewinde (mm)
Steigung (mm)
Wirkung-sgrad
18000 65 M01 IEC112(Flansch+Kupplung)
4 1400 1:5 40 14 0,30
29000 33 M02 IEC112(Flansch+Kupplung)
4 1400 1:5 40 7 0,24
36500 11 M03 IEC90(PAM) 2,2 2800 1:30 40 7 0,1850000 5 M04 IEC90(PAM) 1,5 1400 1:30 40 7 0,18
LEISTUNGEN HRS50 VRSKraft (N)
Geschw. (mm/s)
Au-sführung
Bauart Motorlei-stung (kW)
Motor-drehzahl
(rpm)
Überset-zung
Gewinde (mm)
Steigung (mm)
Wirkung-sgrad
30000 47 M01 IEC90(PAM) 1,8 1400 1:5 50 10 0,8145000 23 M02 IEC90(PAM) 1,5 1400 1:10 50 10 0,7750000 7 M04 IEC71(Getrie-
beMotor)0,55 2800 1:10
1:750 10 0,64
50000 5 M05 IEC71(Getrie-beMotor)
0,25 1400 1:101:7
50 10 0,64
Baugröße HRS50 TPN HRS50 VRSA 575 715B 10 112C 60 70D 85 140E 105 132G 103 121
PAM
GET
RIEB
E M
OTO
RFL
AN
SCH
UND
KUPP
LUN
G
Baugröße (Flansch und
Kupplung Version)IEC90 IEC112
D1 Ø24 Ø28D2 Ø130 Ø180D3 Ø165 Ø215D4 Ø200 Ø250F M10 Ø14.5L1 4.5 5L2 52 68L3 183 231T 8 8T1 27.3 31.3
G
A + Hub
B + Hub
45 - Version 2018
HRS
LEISTUNGEN HRS100 TPNKraft (N)
Geschw. (mm/s)
Au-sführung
Bauart Motorlei-stung (kW)
Motor-drehzahl
(rpm)
Überset-zung
Gewinde (mm)
Steigung (mm)
Wirkung-sgrad
38000 42 M01 IEC132(F+K) 7,5 1400 1:5 55 9 0,2158000 14 M02 IEC112(PAM) 5,5 2800 1:30 55 9 0,1687000 7 M03 IEC112(PAM) 4 1400 1:30 55 9 0,16100000 2 M04 IEC80(Getrie-
beMotor)1,8 2800 1:7
1:3055 9 0,16
LEISTUNGEN HRS100 VRSKraft (N)
Geschw. (mm/s)
Au-sführung
Bauart Motorlei-stung (kW)
Motor-drehzahl
(rpm)
Überset-zung
Gewinde (mm)
Steigung (mm)
Wirkung-sgrad
51000 47 M01 IEC100(F+K) 3 1400 1:5 63 10 0,8170000 23 M02 IEC100(F+K) 2,2 1400 1:10 63 10 0,7792000 8 M03 IEC90(PAM) 1,1 1400 1:30 63 10 0,67100000 5 M04 IEC71(Getrie-
beMotor)0,75 2800 1:10
1:1063 10 0,62
100000 2 M05 IEC71(Getrie-beMotor)
0,55 2800 1:301:7
63 10 0,55
Baugröße HRS100 TPN HRS100 VRSA 706 780B 10 133C 80 80D 120 150E 122 137G 121 141
PAM
GET
RIEB
E M
OTO
RFL
AN
SCH
UND
KUPP
LUN
G
Baugröße (Flansch und
Kupplung Version)
IEC100 IEC112 IEC132
D1 Ø28 Ø30D2 Ø180 Ø230D3 Ø215 Ø265D4 Ø250 Ø300F Ø14,5 Ø14,5L1 5 5L2 68 91L3 239 274T 8 10T1 31,3 41,3
G
A + Hub
B + Hub
46 - Version 2018
HRS
LEISTUNGEN HRS200 TPNKraft (N)
Geschw. (mm/s)
Au-sführung
Bauart Motorlei-stung (kW)
Motor-drehzahl
(rpm)
Überset-zung
Gewinde (mm)
Steigung (mm)
Wirkung-sgrad
44000 47 M01 IEC132(F+K) 9,2 1400 1:5 70 10 0,23490000 16 M02 IEC132(F+K) 7,5 2800 1:30 70 10 0,1924130000 8 M03 IEC132(F+K) 5,5 1400 1:30 70 10 0,1924200000 2 M04 IEC90(Getrie-
beMotor)2,2 2800 1:7
1:3070 10 0,1924
LEISTUNGEN HRS200 VRSKraft (N)
Geschw. (mm/s)
Au-sführung
Bauart Motorlei-stung (kW)
Motor-drehzahl
(rpm)
Überset-zung
Gewinde (mm)
Steigung (mm)
Wirkung-sgrad
125000 47 M01 IEC132(F+K) 9,2 1400 1:5 80 10 0,81174000 23 M02 IEC132(F+K) 5,5 1400 1:5 80 10 0,77200000 7 M03 IEC90(Getrie-
beMotor)2,2 2800 1:10
1:780 10 0,64
200000 3 M04 IEC90(Getrie-beMotor)
2,2 2800 1:101:15
80 10 0,60
Baugröße HRS200 TPN HRS200 VRSA 860 996B 80 142
GET
RIEB
E M
OTO
RFL
AN
SCH
UND
KUPP
LUN
G
A + Hub
B + Hub
47 - Version 2018
HRS
VORDERES ENDEVorderes Ende Abmessungen
HRS50 HRS100 HRS200TPN VRS TPN VRS TPN VRS
A3
A 660 815 834 908 1053 1189B 54 72 104C 30 35 60D Ø30 Ø35 Ø60E 55 70 120F 55 70 120
A4
A 667 822 815 889 1020 1156G Ø30 Ø35 Ø60H r. 35 r. 40 r. 68,5I 37,5 43 44
A7A 532 687 671 745 820 956L M30X2 M36X2 M52X3M 55 70 80
A + Hub
A + Hub
A + Hub
B
C
D
E
H
G
I
M
L
F
A3
A4
A7
48 - Version 2018
HRS
BESTELLSCHLÜSSEL
MODELLHRS50HRS100HRS200
HUB (mm)Z. B. 250 mm = 0250 (Hub>350mmHinzufügen50mm)
GESCHWINDIGKEIT (mm/s)AC-VersionPAM:RPM
MOTORAC:Version/Spannung/Type/Größe/Drehzahl/LeistungPAM:0
MOTOROPTIONEN
MOTORLAGEKeine:Freilassen M0:rechts M1:links
KLEMMKASTENLAGEKeine:Freilassen 1
ENCODERKeine:Freilassen
ENDSCHALTER Keine:Freilassen
HINTERES ENDEP1:RundesEnde P2:RundesEnde90°
VORDERES ENDEA1: Rundes Ende A4: Gelenkauge A3:Gabelkopf A7:Außengewinde
OPTIONEN (SieheletztesKapitel)
HRS50/0250/M01/AC-400/50-T-56-4-0,09/AB/M0/1/E01/2FCI/P1/A1/
49 - Version 2018
LTECHNISCHE DATEN L
Motor mit Permanentmagnet 12, 24 VDC•Schneckengetriebe•Trapezgewinde bzw. Kugelumlaufspindel•Schubstange aus verchromtem Stahl•Dauerschmierung mit Fett •IP 65•Betriebstemperatur –10°C bis +60°C•Einschaltdauer S3 30 % (5 min) bei 30°C•Endschalter und Inkrementalgeber auf Anfrage•
MecVel behält sich das Recht vor, Produktinformationen und/oder Funktionen ohne vorherige Ankündigung zu ändern. Alle in diesem Katalog enthaltenen Daten sind rein indikativ und für das Unternehmen nicht verbindlich
LINEARANTRIEBE L
Max Belastung: 5.000 NMax Geschwindigkeit: 100 mm/s
DC
50 - Version 2018
L
LEISTUNGEN L
L02 24 VDCKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
280 100 M01 36 - 500220 60 M02 36 - 300240 40 M03 36 - 300750 30 M04 36 - 150840 20 M05 36 - 150
1600 10 M06 36 - 1502000 5 M07 36 80
L02 VRS 24 VDCKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
1000 42 M01 36 - 5001000 25 M02 36 - 3002000 12 M03 36 - 1502000 6 M04 36 - 80
L03 24 VDCKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
3000 20 M01 51 - 1555000 10 M02 51 - 1552000 30 M03 51 - 155
L03 VRS 24 VDCKraft (N) Geschw. (mm/s) Ausführung Bauart Motorleistung (kW) Motordrehzahl (rpm)
5000 13 M01 51 - 155
12 VDC Motor - Stromaufnahme verdoppelt sich und Drehzahl sinkt um 20%•
51 - Version 2018
L
ABMESSUNGEN L02
ABMESSUNGEN L03
KoLBENSTANGENENDE L02
Maß Hub < 320 mm Hub > 320 mmB 228 + Hub 239 + Hub
B1 257 + Hub 268 + Hub
Ø36
15
Ø10 +0.1 0
13
25
33
820
172
Ø10 +0.1 0
Ø25
10
20
B1 + HubMit Encoder
Ø48
45° 45°
B + Hub
Kabel Encoder
Kabel Motor
Maß Hub < 320 mm Hub > 320 mmB 325 + Hub 336 + Hub
B1 355 + Hub 366 + HubB2 355 + Hub 366 + Hub
15 + Hub
B + Hub
264
30
35
Ø10+0.1 0
39
19
Ø36
Ø25
Ø10+0.1 0
10
26 Ø65
45° 45°
8
Kabel Encoder
Kabel Motor
B1 + HubMit Encoder
B2 + HubMit Bremse
B = 228 + Hub
27
2025
Ø10 +0.1 0
13 10
Ø25
Ø10 +0.1 0
68
6
A1 = RUNDES ENDE (STANDARD)
B = 290 + Hub
20
12
2010
20
Ø10 H8
27
20
68
6
13
Ø10 +0.1 0
B = 237 + Hub
25
13
Ø10 +0.1 0
32
Ch.1
9M
10
27
20
68
6
A3 = GABELKOPF
A7 = AUSSENGEWINDE M10
B = 294 + Hub13 15
1410.5
Ø30Ø10 H7
27
20
68
6
Ø10 +0.1 0
A4 = GEKENKAUGE
Abmessung „B“ variiert je nach Modell
L02: Hub > 320 + 11 mm•L02-FCM: + 34 mm•L02-FCM: Hub > 320 + 45 mm•L02 VRS: + 40 mm•Mit Passfedernut G + 30 mm•
52 - Version 2018
L
KoLBENSTANGENENDE L03
BESTELLSCHLüSSEL
MoDELLL02 L02-FCM L02 VRSL03 L03-FCM L03 VRS
HUB (mm)Z. B. 250 mm = 0250 (Hub > 350 mm Hinzufügen 50 mm)
GESCHWINDIGKEIT (mm/s)DC-Version
MoToR12: 12 VDC 24: 24 VDC
ENCoDERKeine: Freilassen E10 (L02) E50 (L03)
ENDSCHALTER Keine: Freilassen
HINTERES ENDEP1: Rundes Ende P2: Rundes Ende 90°
VoRDERES ENDEA1: Rundes Ende A4: Gelenkauge A3: Gabelkopf A7: Außengewinde M10
opTIoNEN (Siehe letztes Kapitel)
L02/0250/M01/12/E10/2FCM0/p1/A1/
B = 325 + Hub
Ø10 +0.1 0
19
39
36
10
Ø25Ø10
+0.1 0
30
118
11
A1 = RUNDES ENDE (STANDARD)
B = 388 + Hub
Ø10 +0.1 0
19
39
36 20
12
2010
20
Ø10 H8
30
118
11
32
Ch.1
9M
10
B = 335 + Hub
Ø10 +0.1 0
19
39
36
30
118
11
A3 = GABELKOPF
A7 = AUSSENGEWINDE M10
B = 392 + Hub
Ø10 +0.1 0
19
39
36
15
1410.5
Ø30
Ø10 H7
30
118
11
A4 = GEKENKAUGE
Abmessung „B“ variiert je nach Modell
L03: Hub > 320 + 11 mm•L03-FCM: + 34 mm•L03-FCM: Hub > 320 + 44 mm•L03 VRS: + 40 mm•Mit Passfedernut G + 30 mm•
53 - Version 2018
MECVEL LINEARANTRIEBE OPTIONEN
ALI1ALI1-F
ALI2ALI2-F
ALI3ALI3-F
ALI4ALI4-F
ALI5ALI5-F AV3 EC HRS L02 L03
Stromversor-gung
AC DC AC DC AC DC AC DC AC DC AC DC AC DC AC DC AC DC AC DC
Endshalter ALI1ALI1-F
ALI2ALI2-F
ALI3ALI3-F
ALI4ALI4-F
ALI5ALI5-F
Potentiome-ter
ALI2ALI2-F
ALI3ALI3-F
ALI4ALI4-F
ALI5ALI5-F
Encoder
Verdrehsi-cherung “L”
Drehmo-mentbe-
grenzer “S”
2’ Wellenen-de gegenü-
ber dem Motor “T”
Sicherheits-mutter “G”
Balg “B”
Handverstel-lung “H”
Inox “A”
Speziallackie-rung “FX”
Stahlindu-strie
Version “AA”
Schwenk Wellen
Klammer Ende
Standard:Nicht Verfügbar:Auf Anfrage:
54 - Version 2018
MOTOR
Version Spannung Typ Bauart Geschwin-digkeit Bremse Motor
OptionenDC (Gleichstrom) 12-24 - - 3000
rpmFECC (DC-Bremse) -
AC (Wechsel-strom)
230-50 Hz400-50 Hz
T (3-Phasen)M (1-Phase)AT (3-Phasen mit Bremse)AM (1-Phase mit Bremse)
IEC 50-56-63-71-80-90-100-112-132
2-4-6-8 Pole
FECA (AC-Bremse)
LS (Hand Entriege-lungshe-bel)AB (Zwei-te Welle)
PD in den Bestellschlüssel eingeben, wenn ein spezieller Motorflansch benötigt wird
ENDSCHALTER FüR ALI1 uND ALI1-F
Dieses Model hat zwei eingebaute Endschalter mit je einem Umschaltkontakt. Die Ausführung mit einem dritten Endschalter in der Mitte ist möglich. Das Justie ren der Endschalter erfolgt durch Verdrehen der Einstellschrauben an der Oberseite des Getriebes. Jeder Endschalter ist einzeln verstellbar. Eine Umdrehung der Schraube verändert den Endschalter um 0,7mm.
A-F: Oben• I: Mittellage• P-B: Unten•
MECHANISCHE ENDSCHALTER
Umschaltbare nockengesteuerte Einzelkontakt-Mikroschalter, integriert in das Hauptgetriebe mit Linearantrieb, bewegt durch ein kleines Getriebe, das mit der Spindel verbunden ist. Das System ist somit geschützt und kompakt, jedoch bei langen Hüben limitiert, da der Hub direkt mit dem Drehwinkel der Nocken in Beziehung steht. Darüber hinaus werden die Stoppgenauigkeit und die Wiederholgenauigkeit durch den nicht selbsthemmenden Zustand des Linearantriebs beeinflusst. Für einige Getriebeübersetzungen steht ein Potentiometer zur Verfügung. Wenn die integrierten mechanischen Endschalter bereits voreingestellt geliefert werden, führt die manuelle Drehung der Schubstange zu Einstellungsveränderungen, sodass der Zylinder auf den mechanischen Endan-schlag fährt, was mechanische Schäden der internen Komponenten zur Folge hat.
Technische Daten:Gehäuse: Phoenolic Melamin thermoplastisch• Mechanik: Sprungschaltkontakt mit Berillium/Bronzefeder. Umschaltkontakt NC/NO• Kontakt: Silber• Anschlüsse: Gold• Mech. Lebensdauer: 3x10• 5 Schaltungen
A-FA-F
P-BP-B
I
I
min. 35Version 2FC
Version 3FC min. 25min. 35
4
1
2
55 - Version 2018
2FC1 und 3FC1 für ALI2-ALI3• 2FC2 und 3FC2 für ALI4-ALI5-AV3-EC• 2FCD und 3FCD für ALI2-ALI3 mit Dioden•
2FC1 3FC1
2FC2 3FC2
2FCD 3FCD
56 - Version 2018
MAGNETENDSCHALTER FCM FüR ALI2, ALI3, ALI4, ALI5 uND L
Magnetschalter werden durch ein Magnetfeld aktiviert, das durch einen an der Spindel-mutter befestigten Magnetring erzeugt wird. Diese Sensoren sind mit Klammern am Außen-rohr befestigt und können nach Belieben gedreht werden, indem die Halterung eingestellt wird. Aufgrund der Größe der Magnetschalter und des vom internen Magneten erzeugten Schaltbandes wird der maximale Arbeitshub reduziert (je nach Größe des Linearantriebs).
Technische Daten Schaltung NCSpannung in DC 3/110 VSpannung in AC 3/110 VStrom bei 25° C 0,5 ALeistung 20 VAAnschlusskabel PVC 2 x 0,14 mm
Schaltung NC:Schaltungen mit Reed-Kontakt-Endschalter, die im ungeschalteten •
Zustand geschlossen sind (NC) und über einen Varistor gegen Überspannung geschützt sind, signalisieren die Schalterstellung „Aus“ mit einem Indikator (LED)
Bestellschlüssel: 2FCM0•
INDuKTIONSSENSOR FCI
Technische DatenSpannung in DC 5-40 VdcTemperaturbereich: -25° C +75° CSchutzklasse IP67Signalisierung LED gelb
FCIC: Induktionssensor Schließer• FCIA: Induktionssensor Öffner• Bestellschlüssel: 2FCI•
SCHALTER
MAGNETFELD
MAGNETRING
SCHALT BAND
Bl / Bl / Br
Schaltung
Br
NC Circuit
NO + NCschwarzbraun
weißblau
+
–
I
FCIC
FCIA
57 - Version 2018
POTENTIOMETER
Ein Drehpotentiometer liefert eine absolute Rückmeldung für die Hubüberwachung. Es kann al-leine oder in Kombination mit Endschaltern montiert werden, um auch die Position der Spinde-lenden zu überwachen. Die Bewegung erreicht das Potentiometer über das gleiche Getriebe wie die integrierten Endschalter, daher können lange Hübe nicht überwacht werden.
Potentiometer Endshalter und Potentiometer
Technische DatenMax. Drehwinkel 340° ± 3°Widerstand 1K/10KSpannung Max. 10 VGleichlaufgenauigkeit ± 2%Toleranz ± 20%Temperaturkoeffizient Widerstand 600 ppm/°C
Bestellschlüssel:POT01A: 1Kohm• POT10A: 10Kohm•
1 2 3
R4.5
3.29.3
1
2
3Ø22
.2
58 - Version 2018
ENCODER
Ein Encoder ist ein inkrementeller Drehgeber, der eine Winkelbewegung in elektrische digitale Impulse umwandelt. Er kann an einer Wellenverlängerung (die mit der gleichen Drehzahl des Motors rotiert) auf dem Linearantrieb montiert werden und auf der gegenüberliegenden Seite des Motors aus dem Getrie-be austritt oder direkt in AC- oder DC-Motoren integriert werden. Sein digitaler Ausgang liefert eine relative Rückmeldung über die Position des Linearantriebs (bei jeder Stromlosschaltung der Maschine muss dem Geber die Nullposition neu mitgeteilt werden, d.h. eine Referenzfahrt ist nötig).
ENCODER FüR DC-MOTOR
Modell Technische Daten Schaltplan Typ
ALI1
Spannung: 5-24 VdcPush-PullSignal: 2 Kanal-4 pprStromabgabe: 20 mA
E00
ALI2ALI3
Spannung: 5-24 VdcOffener Kollektor NPN2 Kanal, 1 Impuls/UmdrehungRechtecksignalMax. Stromabgabe: 100 mA
E01
L02
Spannung: 4,5-18 VdcNPN + Vorschaltwiderstand 3,9 KΩ1 Kanal, 4 Impuls/UmdrehungRechtecksignalMax. Stromabgabe: 100 mA
E10
L03
Spannung: 4,5-18 VdcNPN + Vorschaltwiderstand 1,2 KΩ2 Kanal, 4 Impuls/UmdrehungRechtecksignalMax. Stromabgabe: 100 mA
E50
ENCODER FüR AC-MOTOR
Bidirektional-Inkremental-Encoder • mit Null-Impuls (Standard) oder ohne Null-Impuls
Schutzart IP54• Mögliche Impulse pro Umdrehung: 1024• Mögliche Ausgangssignale: Linearsignal 5 VDC•
+ VDC
0 VDC
OutOut
+V DC
0V DC
OUT
ROTBLAUORANGEGRÜN
OUT 1OUT 2
BRAUNWEIßGRÜNGELB
OUT 1OUT 2
BRAUNWEIßGRÜNGELB
OUT 1OUT 2
SchaltplanRot ÷VDCSchwarz 0 VDCGrün AGelb BBlau ZBraun - AOrange - BWeiß - Z
59 - Version 2018
ENCODER - BESTELLSCHLüSSEL
E00: Abhängig von der Ausführung (Push Pull 2 Kanal 4 ppr)• E01: Inkremental-Encoder direkt Anbau am DC-Motor (NPN 2 Kanal 1 ppr)• E06: Inkremental-Encoder direkt Anbau am AC-Motor (Mögliche Impulse pro Umdre-• hung: 1024)E10: für L02 (NPN 1 Kanal 4 ppr)• E50: für L03 (NPN 2 Kanal 4 ppr)•
Modell E00 E01 E06 E10 E50
ALI2 DC
ALI2 AC
ALI3 DC
ALI3 AC
ALI4
ALI5
AV3
EC
HRS
L02
L03
Au Anfrage:
60 - Version 2018
VERDREHSICHERuNG “L”
In Sonderfällen kann eine Verdrehsicherung eingebaut werden. Bei den Enden A3/A4/A7 muss immer eine Verdrehsicherung eingebaut sein.
DREHMOMENTBEGRENzER “S”
Der Drehmomentbegrenzer befindet sich zwischen Motor und Getriebe, um eine gelegentliche Überlastung zu vermeiden. Erhältlich für DC- und AC-Motoren mit IEC-Flansch. Der Drehmomentbe-grenzer reagiert bei 150-160% der Nennlast und kann nicht als Hubbegrenzung eingesetzt verwen-det werden, wenn der Linearantrieb an den mechanischen Endanschlag kommt.
2’ WELLENENDE GEGENüBER DEM MOTOR “T”
Verfügbar für ALI4-Modell auf Anfrage.
Verfügbar für ALI5-Modell auf Anfrage.
Verfügbar für ALI2- und HRS-Modelle auf Anfrage.
65.8
26.3
164
Ø10
11.2
Ø40
M5
3
93 68.5
30
5 20
12.5
4
Ø11
61 - Version 2018
SICHERHEITSMuTTER “G”
Die Sicherheitsmutter aus Stahl ist mit der Hauptmutter aus Bronze verbunden, die sich entlang des Hubs bewegt. Sie wurde so entwickelt, dass sie bei maximalem Verschleiß der Hauptmutter oder bei einem plötzlichem Bruch der Hauptmutter eingreift, so dass die Last nicht fallen kann. Das Innengewinde der Sicherheitsmutter ist mit der Hauptspindel verbun-den, hat aber eine andere Steigung im Vergleich zur Spindel: D.h. dass auch im Falle eines Bruches der Hauptmutter nach einigen Bewegungen die Verbindung die Sicherheitsmutter auf die Spindel greift, wodurch das System vollständig verriegelt wird. Somit werden Schäden an anderen Komponenten vermieden und die gesamte Anwendung bleibt erhalten. Diese Sicherheitsmutter kann sowohl im Schub- als auch im Zugbetrieb arbeiten und eignet sich neben der Druck- und Zugbelastung auch für den Fall von Lasten.
BALG “B”
Diese Option eignet sich für alle Anwendungen, wo es erforderlich ist, die Spindel und die Schubstange vor der Arbeitsumgebung zu schützen.
62 - Version 2018
HANDVERSTELLuNG “H”
Die Option ist für AC-Motoren erhältlich, so dass die Linearaktuatoren manuell zurückge-fahren werden können, falls die Stromversorgung ausfällt. Zweite Wellenenden am Motor oder verlängerte Schneckenwellen aus den Getrieben können manuell mit Handrädern betätigt werden. Das Übersetzungsverhältnis und die Spindelsteigung definieren die An-zahl der Umdrehungen die durchgeführt werden müssen, um die Einheit über den gesam-ten Hub des Linearantriebs. Zu verfahren es ist nicht erlaubt, das Handrad zu verwenden, wenn der Motor an die Stromversorgung angeschlossen ist. Bevor Sie den Motor an-schließen, denken Sie daran, den Sicherheitsmikroschalter MS, der sich auf dem Handrad befindet, anzuschließen: Die Stromversorgung wird beim Drücken des Sicherheitsmikro-schalters vom Motor getrennt.
Für ALI1 Modell eine manuelle Verstellung ist im Notfall möglich. Nach Entfernen der Abdeckung kann die Schnecke mit einem Schraubendreher verstellt werden.
INOX “A”
Die Edelstahlversion beinhaltet Front-, Rückseite und Schubstange aus Edelstahl.Bei den Modellen AV3 und EC besteht die Schubstange aus doppelt verchromtem Stahl.
T1
ØD
ØA
B
C
T
MS
AbmessungenModell A B CALI2ALI3ALI4ALI5EC1EC2EC3EC4
Ø150 65 44
HRS50HRS100 Ø200 90 53
AV3EC5HRS200
Ø250 90 66
BolognaBologna
63 - Version 2018
SPEzIALLACKIERuNG “FX”
Spezielle Antikorrosionsbeschichtung für alle Metalloberflächen, aber auch für viele ande-re Materialien wie Stahl, Aluminium und Legierungen, Messing, Kupfer, Gusseisen, Holz, Faserplatten, Fliesen, Glas, Keramik, Hartfaser und Glasfasern. Die Speziallackierung ist in der Lage, gegen Schäden gegen aggressive Mittel wie Meerwasser, Industriedämpfe, saurer Regen, UV-Strahlung, Öle, Reinigungsmittel und chemische Produkte zu beste-hen. Sie hat auch eine ausgezeichnete Adhäsion und Beständigkeit gegen Stöße und Abrieb und bietet einen lang anhaltenden Schutz für Produkte, die in den härtesten Arbeitsumgebungen und insbesondere im industriellen Umfeld eingesetzt werden.
STAHLINDuSTRIE VERSION “AA”
Diese Option beinhaltet:Größere Endschalterbox• Messingräder und -nocken• Metallstecker• Viton Dichtungen• Mechanische Begrenzer mit Warnsensor• Handrad für manuelles Fahren• Vorderes Ende mit Stoßdämpfer•
64 - Version 2018
GELENKLAGERuNG FüR DIE EC-SERIE “SP”
Zur Montage und Befestigung von Linearantrieben der EC-Serie sind vier verschiedene Größen von Wellenhaltern erhältlich. Jedes SP Kit enthält 2 Wellen.
Code Beschreibung Abmessungen
SP0014Kit mit 2 Wellenhaltern für EC1
SP0020Kit mit 2 Wellenhaltern für EC2
14
G7
50
150
20
120 14
0
110
10
20
32
14 f7
14 f7
1215
31
20
PIN
20 G
7
145
120
50
110
20
150
14
30
37
20 f7
20 f7
3030
65
30
PIN
65 - Version 2018
Code Beschreibung Abmessungen
SP0030Kit mit 2 Wellenhaltern für EC3
SP0040Kit mit 2 Wellenhaltern für EC4 und EC5
30
G7
155
120
14
110
2015
0
56
50
40
42
40
G7
160 20
5
18
200
3026
0
75
70
50
55
30 f7
30 f7
29.5
3266
.5
39
40 f7
40 f7
4242
89
50
PIN
PIN
66 - Version 2018
HALTERuNGEN FüR DAS VORERE uND HINTENERE ENDE “SAA”
Für die Montage und Befestigung von Linearaktuatoren mit dem hinteren Ende P1 oder P2 und dem vor-deren Ende A1 oder A4, sind Halterungen für folgende Modelle verfügbar: ALI2, ALI3, ALI4, ALI5.
Code Beschreibung Abmessungen
SAA0002Asymmetrische Halterung für ALI2 vorderes und hinteres Ende
SAA0003Asymmetrische Halterung für ALI3 vorderes und hinteres Ende
3610
10
h8
5473
284
Ø9
20.5
R12
R12
46
54
73
284
7Ø9
46
R12
R12
3610
27.2
10
h8
67 - Version 2018
Code Beschreibung Abmessungen
SAA0004Asymmetrische Halterung für ALI4 vorderes und hinteres Ende
SAA0005Asymmetrische Halterung für ALI5 vorderes und hinteres Ende
5581
85110
95.5
80.5
N°4
fori
11
13
12.5
15
58
26.1
20
h11
5
85110
80.512.5
66
15
81 5513
99.5
N°4
fori
Ø 11
Ø 1
2 h1
1
30
13
68 - Version 2018
SALES CONDITIONSArt. 1 Applicable law and conclusion of the contract
1.1 Any matter regarding the relationship between MECVEL and the Buyer that is not explicitly or implicitly resolved by the dispositions of the present General Sales Conditions or by possible special conditions agreed upon by the parties and settled in the sale contract (that in case of contrast will be considered prevailing) will be governed by the Italian law. 1.2 Any modification to the present General Sales Conditions must be made in writing. 1.3 The sale contract (hereinafter called “contract”) has to be considered as concluded when, on reception of an order, the Producer has sent an acceptance in writing within the term eventually fixed by the Buyer.
Art. 2 Characteristics of the products and descriptive documents
2.1 Any information relating to working characteristics of the products, weights, dimensions, abilities, prices, outputs, and other data contained in catalogues, prospects, circulars, advertising, illustrations or price-lists of the Producer, have cha-racter of approximate indications. These information shall be binding only to the extent they are expressly referred to in the contract. 2.2 Any design or technical document enabling the manufacture of the supplied products or their parts, which the Producer has delivered to the Buyer before or after the stipulation of the contract, remains the Producer’s property, and the Buyer cannot use, copy, reproduce, transmit or communicate it to third parties without the consent of the Producer. 2.3 The title of any intellectual or industrial right related to the products is and remains of the Producer.
Art. 3 Price
3.1 Unless otherwise agreed the price does not include value added tax, packing, custom costs, transport and accessory expenses and it is subject to change according to the Producer.
Art. 4 Testing
4.1 Whether technical specifications for the tests are not specified in the contract, the tests will be carried out according to the procedures generally followed by the Producer. 4.2 If the Buyer claims for it at the moment of the order, the Producer has to communicate to him when the tests will take place, in order to allow his representatives to be present. 4.3 Unless otherwise agreed the Producer will be charged of all the expenses of the tests carried out in his establishments, in exception of those for the personnel of the Buyer.
Art. 5 Payment conditions and retention of title
5.1 Payments must be made with the means and to the expiration or expirations arranged by the parties. The obligation of payment is considered fulfilled when the due amount is received from the bank of the Producer in available funds. 5.2 If the delivery occurs before the complete payment, the Products delivered remain the Producer’s property until complete payment is received by the Producer.
Art. 6 Interests on delayed payment
6.1 In case of delay in any payment by the Buyer, the Producer can actually suspend the fulfillment of his own obligations until complete payment is done. 6.2 In addition to what is expressed in the preceding point, the Producer will have the right to interests on delayed pay-ment on the amount that is not paid to the agreed date, beginning from the moment in which the payment is due up to the moment in which the payment is made, previous written notice to the Buyer.6.3 Whether the delay of the Buyer in making any payment depends on a circumstance listed under article 10, the Producer is not entitled to any interest on delayed payment. 6.4 Whether the delay of the Buyer exceeds 60 days from the agreed date, the Producer has the right to withdraw from the contract, and consequently to get from the Buyer the restitution of the products and the compensation for dama-ges, previous written notice to the Buyer and without having to require a favorable sentence of any Court.
69 - Version 2018
Art. 7 Time of delivery
7.1 Except as otherwise agreed, the supply of goods will be Ex Works the Producer’s establishment. The tran-sfer of risks is determined in conformity to the Incoterms of the International Chamber of Commerce, in force at the moment of the contract conclusion. 7.2 Shall the delivery be delayed for any of the circumstances listed under article 10, or for any action or omission of the Buyer, a reasonable extension of the term of such delivery will be granted, considering all the circumstances of the delay. 7.3 Whether the Buyer does not withdraw the products to the agreed time, however he shall be engaged to make all the payments relating to the delivery as if the material had been delivered. The Producer shall care for the storage of the material at the Buyer’s expenses and risks. On application of the Buyer the Producer has to assure the material at expenses of the Buyer. 7.4 Except if the Buyer does not withdraw the material because of one of the circumstances specified under article 10, the Producer can require the Buyer to withdraw the material within a reasonable term. Shall the Buyer, for any reason, not comply in the aforesaid term, the Producer shall have the right to withdraw from the contract, in regard to the part of the supply undelivered because of the above-mentioned breach of the Buyer, and consequently to get from the Buyer the compensation for those damages suffered because of his breach, previous written notice to the Buyer and without having to require the favorable sentence of any Court. 7.5 Possible penalties for delivery delays due to the Producer must be specified in writing at the conclusion of the sale contract, and they shall exclude any other remedy for his delayed delivery or non-delivery.
Art. 8 Warranty
8.1 Within the limits of the following dispositions, the Producer undertakes to remedy any imperfection that is consequence of any project, materials, or processing defect. Such obligation is limited to defects occur-ring during the period (hereinafter called “warranty period”) of 12 months from the date of delivery to the Buyer.8.2 In order to claim the rights settled in the present article, the Buyer has to notify the Producer of all the manifested defects in writing, and he has to give him any possibility to ascertain and remedy them. 8.3 Upon reception of such notification during the warranty period, the Producer has to remedy the above mentioned defects at his own expenses. Except when the nature of the defects makes it convenient to carry out the reparation on the place, the Buyer shall forward the defective parts to the Producer, so that the latter can repair or replace them. The obligations of the Producer are considered duly carried out with the delivery to the Buyer of the repaired or replaced parts. 8.4 Except as otherwise agreed, the Buyer undertakes to bear all the costs and risks of transport of the defec-tive parts, and the Producer those of the repaired or replaced ones, between the place where the material is located and the seat of the Producer and vice versa. 8.5 The defective products which the Producer has replaced according to the present article will be returned to the Producer within and not later than 15 days, from the date of reception of the goods sent for replace-ment, by the Buyer or by one of his customers on his behalf. 8.6 The liability of the Producer is limited to those defects manifesting under conditions of employment as pro-vided in the contract and during a correct use. The guarantee does not cover defects due to causes arising after the transfer of the risks as described under clause 7.1, neither it concerns the normal deterioration. 8.7 Specially, the Buyer loses the right to the guarantee in the following cases: failure to comply with the instructions of use, installation and maintenance of the contractual products and the original spare parts, any modifications made to the products and their original spare parts without prior written consent of the Producer; any repairs made to the contractual products by persons not belonging to the Producer’s network and using non-original spare parts.
70 - Version 2018
Art. 9 Civil liability of the Producer
9.1 Shall the Buyer or his customers modify the products or use them for purposes other than those indicated in the catalogue without having obtained prior written consent to do so from the Producer, the Producer shall not be held liable for any loss or damage caused to people or property. 9.2 Pursuant to and for the purposes of Presidential Decree no. 224/88 the Producer shall be liable for any damages caused to third parties deriving from the use of the contractual products only in the event that the injured party is able to provide unassailable proof of the existence of the damage claimed, and of the causal link between any defects and the damage.9.3 The Producer shall not be liable in the following cases: if the defect that has caused the damage did not exist at the moment the Producer delivered the contractual products to the Buyer; if the injured party, while aware of the defect and the danger to which it might give rise, deliberately exposed itself to it; if the damage is caused by a failure to comply with the instructions set out in the manual of use and maintenan-ce of the contractual products, or when it is caused by the use of non-original spare parts mounted on the contractual products. 9.4 The Buyer shall promptly notify the Producer of any accident or potential safety issue relating to use of the contractual products.
Art. 10 Force majeure
10.1 Neither party shall be held in any way liable for any non-fulfillment of one of its obligations if, after the conclusion of the contract, there arise unexpectedly causes that prevent the fulfillment (such as strikes, fires, mobilizations, requisitions, embargo, monetary restrictions, riots, deficiency of means of transport, general lacks of raw materials and restrictions to the use of energy), to the extent in which it provides the proof (a) that such non-fulfillment was caused by unforeseeable events beyond its control, and (b) that at the moment of conclusion of the contract it could not reasonably foresee such event and its effects on its attitude to perform its contractual obligations, and (c) that it could not reasonably avoid or overcome such event or overcome its effects. 10.2 The party claiming for liability exemption shall notify the counterpart, as soon as possible and immedia-tely after having discovered the impediment and its effects on its attitude to perform its obligations, of the existence of such impediment, as well as the effects of the same on its attitude to face its own obligations. Similar communication must be given as soon as the cause of liability exemption fails. Failure by the brea-ching party in giving such communication has the effect to make this party responsible for those damages that otherwise could have been avoided. 10.3 Whether the causes of liability exemption last for more than six months, each party shall have the right to terminate the contract. The parties will arrange the repartition of the expenses born up to that moment for the execution of the contract.
Art. 11 Jurisdiction
11.1 Any matter arising from the present General Sales Conditions and from the single sale contracts gover-ned by them, shall be of exclusive competence of the Court of Bologna. However, as an exception to the above mentioned principle, the Producer is in any case entitled to bring his action before the competent court of the place where the Buyer has his registered seat.