LEMOAT - SPECTO GmbH · 2020. 11. 18. · Disclaimer Measurement Uncertainty: Unless otherwise...

26
FFP2 Maske - LEMOAT BY01 Eigenschaften Standard EN 149: 2001 + A1: 2009 Klassifizierung FFP2 Maße ca. 100 x 155 mm Nutzungsdauer Einmalgebrauch Einstellbarer Nasenclip Ja Atemwiderstand ca. 1,8 mbar (bei 95l/min) Kennzeichnung auf der Maske LEMOAT BY 01 Einzelverpackung 50 Stk je Box FFP2 Masken sorgen bei sachgemäßer Verwendung und richtiger Trageweise dafür, dass mehr als 95% möglicher gesundheits- schädlichen Staubes, Rauch und Aerosolen aus der Luft gefiltert werden. Diese Masken sind für den Einmalgebrauch vorgesehen und soll- ten nicht wiederverwendet werden. Mit dem einstellbaren Metallclip im Nasenbereich kann die Pass- form der Maske so angepasst werden, dass möglichst keine Luft an der Maske vorbeiströmen kann. Durch den Verzicht auf ein zusätzliches Ventil wird auch die aus- geatmete Luft gefiltert und somit das Infektionsrisiko für umge- bende Personen bei einem möglicherweise infizierten Träger re- duziert. LEMOAT TM

Transcript of LEMOAT - SPECTO GmbH · 2020. 11. 18. · Disclaimer Measurement Uncertainty: Unless otherwise...

Klassifizierung FFP2
Nutzungsdauer Einmalgebrauch
Kennzeichnung auf der Maske LEMOAT BY 01
Einzelverpackung 50 Stk je Box
FFP2 Masken sorgen bei sachgemäßer Verwendung und richtiger Trageweise dafür, dass mehr als 95% möglicher gesundheits- schädlichen Staubes, Rauch und Aerosolen aus der Luft gefiltert werden.
Diese Masken sind für den Einmalgebrauch vorgesehen und soll- ten nicht wiederverwendet werden.
Mit dem einstellbaren Metallclip im Nasenbereich kann die Pass- form der Maske so angepasst werden, dass möglichst keine Luft an der Maske vorbeiströmen kann.
Durch den Verzicht auf ein zusätzliches Ventil wird auch die aus- geatmete Luft gefiltert und somit das Infektionsrisiko für umge- bende Personen bei einem möglicherweise infizierten Träger re- duziert.
LEMOAT TM
cotton Specifications:10*15.5 CM
Executive Standard: EN149:2001+A1: 2009 to Regulation (EU) 2016/425
The Manufactured date: Month /
Year Storage Life:2 years
package) Manufacturer: ZHEJIANG BAIYI MEDICAL TECHNOLOGY CO,LTD
Address:2/F,WORKSHOP5,NO.500,SHENLIROAD,WUCHENGDISTRICT,JINHUA
Use Range
FILTERING HALF MASK Respirator suitable for prevent all kinds of particles .
Not suitable for respiratory protection against harmful gases and vapours
Not suitable for use in hypoxia environments ,underwater work,escape and fire fighting.
Storage and transportation:The product should be sealed,not damaged,not stained,and protected
from moisture during storage and transportation.Pay attention to fireproof,rainproof,acid
proof,alkali proof,and avoid direct light.
Storage method: Please store in a dry and ventilated environment,The storage temperature is -
30~40 and the relative humidity is not more than 80%.
USAGE
1. Face the mask without the nose clip,and the nose clip should be on top.
2. Hold the mask on your face and against you chin.
3. Pull the straps on both sides and hang on the ears,and adjust till you feel comfortable.
4. Put your fingers in the middle of the metal nose clip, and move your fingers to both sides until
the nose clip is fully pressed into the shape of the nose slope.
5. Put your hands on your face to check the tightness with your face.
Meaning of logo
Single use Keep out of direct sunlight
Maximum relative humidity of The temperature range of storage conditions storage conditions
See the information provided by the manufacturer CE mark and Notified
2163 Body No
Warning Warnings 1.B efore use the masks first verify that it is suitable for the intended use. The wearer mus t
be adequately trained prior to use and ensuring the masks are proper fit. 2. The mask is disposable and cannot be reused. 3. Using the masks with facial h air w ill c ause leakage p roblem, if t he facial h air not
covered, unlikely to achieve seal. 4. Discard and replace the mask if it becomes damaged or higher breathing resistance. 5. Don’t use the mask i n explosive gas, heavily polluted e nvironment, oxygen-deficient
environment, fire environment and the underwater work. 6. Patients with heart disease or other disease should discard it after wearing uncomfortably. 7. Masks marked ‘’ NR’’ shall not be used for more than one shift. 8. This product does not s upply oxygen. U se only in adequately ventilated a reas
containing s ufficient oxygen to s upport life. D o not u se t his respirator when oxygen concentration is less than 19.5%.
9. Do not use in explosive atmospheres. 10. It is strictly prohibited to use after the package is damaged. The EU DoC is to be delivered with accompanies the user information and masks together. The Notified Body Universal Certification and Surveillance Service Trade Ltd. Co. Necip Keyap Sitesi E2 Blok No: 44/84 Dudullu Ümraniye-Istanbul NB:2163
Page 2o f 5
Test Report No.KZ2021498
This report may not be published excepti n full unless permission fort he publication of an approved extract has been obtained in writing.
Conditions:
The test results presented in this report relate to the samples tested only.
This report may be reproduced and distributed to your clients, provided that it is reproduced and distributed in full.
The authenticity of this test report and its contents can be verified by contacting the laboratory.
Conclusion
Clause 7.16 Breathing resistance Pass
Remarks: Pass = Meet EN 149:2001+A1:2009 FFP2 Requirement Fail = Below EN 149:2001+A1:2009 FFP2 Requirement N/A = Not Applicable
Disclaimer Measurement Uncertainty: Unless otherwise agreed upon, Pass or Fail verdicts are given based on the measured values without any considerations of measurement uncertainties. Please note, every test method has a measurement uncertainty which has been evaluated by the laboratory according to ISO/IEC 17025 requirements. By taking measurement uncertainties into account it might happen that measured values can neither be assessed as Pass nor as Fail.
Page 3o f 5
Test Report No.KZ2021498
This report may not be published excepti n full unless permission fort he publication of an approved extract has been obtained in writing.
Test Results
7.9.2 Penetration of filter material Pass1
The penetration of the filter of the particle filtering half mask shall meet the following requirements.
Sodium chloride test 95 L/min Paraffin oil test 95 L/min
FFP1 20% 20%
FFP2 6% 6%
FFP3 1% 1%
Note 1: FFP2 respirator. Test results are shown in Annex A Table 7.9.2.
7.16 Breathing resistanceP ass2
FFP1 0.6 2.1 3.0
FFP2 0.7 2.4 3.0
FFP3 1.0 3.0 3.0
Note 2FFP2 respirator.Testr esults ares hown in AnnexA Table7 .16.
End of Test Results
Page 4 of 5
Test Report No.KZ2021498
This report may not be published except in full unless permission for the publication of an approved extract has been obtained in writing.
Annex A: Summarization of Test Data
Table 7.9.2 Penetration of filter material Test specification: EN 149:2001+A1:2009 Clause 8.11
Aerosol Condition Sample No. Penetration (%) Assessment
Sodium chloride test As received
01 3.54
04 4.39
05 4.32
06 4.29
Table 7.16 Breathing resistance (mbar) Test specification: EN 149:2001+A1:2009 Clause 8.9
As
received
Flow rate 07 08 09
A B C D E A B C D E A B C D E
Inhalation 30 L/min 0.40 0.61 0.66 0.64 0.63 0.49 0.64 0.62 0.62 0.61 0.56 0.55 0.59 0.60 0.62
95 L/min 2.21 2.17 2.37 2.38 2.23 2.14 2.29 2.35 2.37 2.24 2.27 2.15 2.27 2.19 2.20
Exhalation 160 L/min 2.81 2.40 2.77 2.89 2.70 2.72 2.19 2.60 2.91 2.81 2.85 2.22 2.65 2.57 2.72
Assessment Pass
A: facing directly ahead; B: facing vertically upwards; C: facing vertically downwards; D: lying on the left side; E: lying on the right side
End of Annex A
Page 5 of 5
Test Report No.KZ2021498
This report may not be published except in full unless permission for the publication of an approved extract has been obtained in writing.
Annex B: photos of sample
End of Annex B