KNX Jal.-u.Heiz.-aktor m.3 Eing. Funktion ......KNX Jal.-u.Heiz.-aktor m.3 Eing. Sicherheitshinweise...
Transcript of KNX Jal.-u.Heiz.-aktor m.3 Eing. Funktion ......KNX Jal.-u.Heiz.-aktor m.3 Eing. Sicherheitshinweise...
KNX Jal.-u.Heiz.-aktor m.3 Eing.
SicherheitshinweiseEinbau und Montage elektrischer Geräte dürfennur durch Elektrofachkräfte erfolgen.Bei Nichtbeachten der Anleitung könnenSchäden am Gerät, Brand oder andere Gefahrenentstehen.Das Gerät ist nicht zum Freischalten geeignet.Angeschlossene Stellantriebe sind – auch imausgeschalteten Zustand – nicht galvanisch vomNetz getrennt.An die Eingänge keine externen Spannungenanschließen, andernfalls kann es zuGeräteschäden kommen und SELV-Potential aufder KNX-Busleitung ist nicht mehr gegeben.Sollen mehrere Antriebe an einem Ausgangparallelgeschaltet werden, unbedingt Angabender Hersteller beachten, gegebenenfallsTrennrelais verwenden. Andernfalls könnten dieAntriebe zerstört werden.Nur Jalousieantriebe mit mechanischen oderelektronischen Endlagenschaltern verwenden.Endlagenschalter auf korrekte Justierung prüfen.Angaben der Motorenhersteller beachten.Diese Anleitung ist Bestandteil des Produktesund muss beim Endkunden verbleiben.
Geräteaufbau
Bild 1
(1) Steuerleitung(2) Programmiertaste und -LED(3) Anschluss Netz- und Lastleitungen
Anschlussbelegung LastleitungenBK, schwarz: Anschluss Außenleiter LBN, braun: Anschluss Jalousieantrieb, AufPK, rosa: Anschluss Jalousieantrieb, AbGY, grau: Anschluss Stellantrieb
Bild 2
Anschlussbelegung SteuerleitungRD, rot: KNX+BK, schwarz: KNX–GN, grün: Eingang 1YE, gelb: Eingang 2WH, weiß: Eingang 3BN, braun: COM Eingänge 1...3
FunktionSysteminformationDieses Gerät ist ein Produkt des KNX-Systems undentspricht den KNX-Richtlinien. DetaillierteFachkenntnisse durch KNX-Schulungen werden zumVerständnis vorausgesetzt. Die Funktion des Gerätes ist softwareabhängig.Detaillierte Informationen über Softwareversionenund jeweiligen Funktionsumfang sowie die Softwareselbst sind der Produktdatenbank des Herstellers zuentnehmen.Planung, Installation und Inbetriebnahme desGerätes erfolgen mit Hilfe einer KNX-zertifiziertenSoftware. Volle Funktionalität mit KNX-Inbetriebnahme-Software ab Version ETS3.0d. Produktdatenbank, technische Beschreibungensowie Konvertierungs- und weitere Hilfsprogrammefinden Sie stets aktuell auf unserer Internet-Seite.
Bestimmungsgemäßer Gebrauch- Schalten elektrisch betriebener Jalousien,
Markisen und ähnlicher Behänge fürNetzspannung AC 230 V.
- Schalten elektrothermischer Stellantriebe - Montage in Gerätedose nach DIN 49073- Anschluss mit beiliegenden
Verbindungsklemmen
Produkteigenschaften- Steuerung von Jalousien, Markisen und
ähnlichen Behängen - Ansteuerung elektrothermischer Stellantriebe- Drei Binäreingänge für potentialfreie Kontakte,
nutzbar als Nebenstelleneingänge zur Vor-Ort-Bedienung
- Versorgung über Bus, keine zusätzlicheVersorgungsspannung notwendig
Jalousiefunktion- Behangposition direkt ansteuerbar- Lamellenposition direkt ansteuerbar- Rückmeldung von Fahrzustand, Behangposition
und Lamellenstellung- Zwangsstellung durch übergeordnete Steuerung- Sicherheitsfunktion: 3 unabhängige Windalarme,
Regenalarm, Frostalarm- Sonnenschutzfunktion
Funktion Stellantriebe- Schaltbetrieb oder PWM-Betrieb- Stellantriebe mit Charakteristik stromlos geöffnet
oder stromlos geschlossen ansteuerbar- Überlastsicher, kurzschlusssicher- Schutz gegen festsitzende Ventile- Zwangsstellung- Zyklische Überwachung der Eingangssignale
parametrierbar.i PWM-Betrieb: Elektrothermische Stellantriebe
besitzen nur die Stellungen Offen undGeschlossen. Im PWM-Betrieb wird durch Ein-und Ausschalten innerhalb der Zykluszeit desAntriebs ein quasi-stetiges Verhalten erreicht.
Informationen für Elektrofachkräfte
Montage und elektrischer Anschluss
GEFAHR!Elektrischer Schlag bei Berührenspannungsführender Teile.Elektrischer Schlag kann zum Todführen.Vor Arbeiten am Gerät freischalten undspannungsführende Teile in derUmgebung abdecken!
Gerät anschließen und montieren
GEFAHR!Bei Anschließen der Bus-/Nebenstellen-und Netzspannungsadern in einergemeinsamen Gerätedose kann dieKNX-Busleitung mit Netzspannung inBerührung kommen.Die Sicherheit der gesamten KNX-Installation wird gefährdet. Personenkönnen auch an entfernten Geräteneinen elektrischen Schlag erhalten.Bus-/Nebenstellen- undNetzspannungsklemmen nicht in einemgemeinsamen Anschlussraumplazieren. Gerätedose mit festerTrennwand (Bild 3) oder separate Dosenverwenden.
Bild 3
(4) Gerätedose(5) Trennwand(6) potentialfreie Kontakte, z. B. für Fensterkontakt
oder Installationstaster
Bild 4
Mindestabstand zwischen Netzspannung und Bus-/Nebenstellenadern: 4 mm (Bild 4).o Last anschließen (Bild 5). Beiliegende
Verbindungsklemmen verwenden. o Gerät an KNX anschließen.o Ggf. potentialfreie Kontakte (6) an Eingänge
anschließen (Bild 2).o Gerät in Gerätedose montieren.
Bild 5
i Im Auslieferungszustand bedienen die Eingänge1 und 2 den Jalousieausgang. Eingang 3 hatkeine Funktion.
Funktion der Eingänge 1 und 2 imAuslieferungszustand
Eingang Schließer Behang
1 kurz betätigen Lamellenverstellen Auf /Stop
1 lang betätigen Auffahren
2 kurz betätigen Lamellenverstellen Ab /Stop
2 lang betätigen Abfahren
Verbindungsklemmen verwenden
Bild 6: Abisolierlänge
o Leiter 9 - 11 mm abisolieren (Bild 6).
Bild 7: Anschluss des feindrahtigen Leiters
o Klemme auf der Seite mit der eckigen Öffnungzusammendrücken und feindrahtigen Leiteranschließen (Bild 7).
Bild 8: Anschluss des eindrahtigen Leiters
o Eindrahtigen Leiter bis zum Anschlag in einerunde Öffnung auf der Installationsseitehineinstecken (Bild 8).
InbetriebnahmeAdresse und Anwendungssoftware ladeno Busspannung einschalten.o Physikalische Adresse vergeben und
Anwendungssoftware in das Gerät laden.o Physikalische Adresse auf Geräteetikett
notieren.
Anhang
Technische DatenVersorgungNennspannung AC 230 / 240 V ~Netzfrequenz 50 / 60 HzSchaltspannung AC 250 V~UmgebungsbedingungenUmgebungstemperatur -5 ... +45 °CLager-/Transporttemperatur
-25 ... +70 °C
JalousieausgangKontaktart µSchaltstrom AC1 3 AMindestschaltstrom AC 100 mAMotoren 230 V 600 VAHeizungsausgangAusgangsart Halbleiter (Triac), εSchaltstrom 5 ... 25 mAEinschaltstrom max. 600 mA (2 s)Anzahl Antriebe proAusgang
max. 2
Steuerleitung und EingängeSteuerleitung(vorkonfektioniert)
YY6x0,6
Eingangsart potentialfreiGesamtlängeNebenstellenleitung
max. 5 m
AbfragespannungNebenstelleneingänge
ca. 5 V
Abmessung Ø×H 53×28 mmAnschlussart Verbindungsklemme
(beiliegend)eindrähtig 1 ... 2,5 mm²KNXKNX Medium TP 1Inbetriebnahmemodus S-ModeNennspannung KNX DC 21 ... 32 V SELVLeistungsaufnahme KNX max. 240 mWAnschlussart KNX Anschlussklemme an
Steuerleitung
Merten GmbH
Bei Warenrücksendungen auf Grund vonBeanstandungen wenden Sie sich bitte an unserService Center:
Merten GmbHLösungen für intelligente GebäudeService CenterFritz-Kotz-Strasse 8Industriegebiet Boming-WestD-51674 WiehlTelefon: +49 2261/702-204 Telefax: +49 2261/702-136 E-Mail: [email protected]: www.merten.de
Bei technischen Fragen wenden Sie sich bitte anunsere InfoLine:Telefon: +49 1805 212581* oder +49 800 63783640 Telefax: +49 1805 212582* oder +49 800 63783630 E-Mail: [email protected]* kostenpflichtig/fee required
KNX Jal.-u.Heiz.-aktor m.3 Eing.Art.-Nr. MEG6003-0006
KNX
Bedienungsanleitung
8257340523.11.2010
KNX Blind- a.Heating-Act.FM w.3 Inputs
Safety instructionsElectrical equipment may only be installed andfitted by electrically skilled persons.Failure to observe the instructions may causedamage to the device and result in fire and otherhazards.The device is not suitable for disconnection fromsupply voltage.The connected actuators are not electricallyisolated from the mains – even when switchedoff.Do not connect any external voltage to theinputs, since doing so may damage the device(s), and the SELV potential on the KNX bus linewill no longer be available.For parallel connection of several drives to anoutput it is essential to observe thecorresponding instructions of the manufacturers,and to use a cut-off relay if necessary. There isotherwise risk of irreparable damage to thedrives.Use only shutter drives with mechanical orelectronic limit switches. Check the limitswitches for correct adjustment. Observe thespecifications of the motor manufacturers.These instructions are an integral part of theproduct, and must remain with the end customer.
Device components
Figure 1
(1) Control cable(2) Programming button and LED(3) Connection of mains and power cables
Connection assignment, power cablesBK, black: connection LBN, brown: connection of Venetian blind, upPK, pink: connection of Venetian blind, downGY, grey: actuator connection
Figure 2
Connection assignment of control cableRD, red: KNX+BK, black: KNX–GN, green: input 1YE, yellow: input 2WH, white: input 3BN, brown: COM inputs 1...3
FunctionSystem informationThis device is a product of the KNX system andcomplies with the KNX directives. Detailed technicalknowledge obtained in KNX training courses is aprerequisite to proper understanding. The function of this device depends upon thesoftware. Detailed information on loadable softwareand attainable functionality as well as the softwareitself can be obtained from the manufacturer´sproduct database.Planning, installation and commissioning of thedevice are carried out with the aid of KNX-certifiedsoftware. Full functionality with KNX commissioningsoftware version ETS3.0d onwards. An updated version of the product database,technical descriptions and conversion programs andother auxiliary programs are available on our Internetwebsite.
Intended purpose- Switching of electrically-driven Venetian blinds,
awnings and similar blinds for AC 230 V mainsvoltage.
- Switching of electrothermal actuators - Installation in appliance box to DIN 49073- Connection with enclosed terminals
Product characteristics- Control of Venetian blinds, awnings and similar
blinds - Control of electrothermal actuators- Three binary inputs for potential-free contacts,
usable as extension inputs for local operation- Supply via bus, no additional power supply
necessary
Venetian blind function- Blind position directly controllable- Slat position directly controllable- Feedback of movement status, blind position
and slat position- Forced position through higher-level controller- Safety function: 3 independent wind alarms, rain
alarm, frost alarm- Sun protection function
Actuator function- Switching operation or PWM operation- Actuators with characteristics opened or closed
without power- Overload-protected, short circuit-protected- Protection against jamming valves- Forced position- Cyclical monitoring of the input signals
configurable.i PWM operation: electrothermal actuators only
have the positions Open and Closed. In PWMoperation, switch-on and switch-off during thedrive's cycle time achieves an almost constantbehaviour.
Information for qualified electricians
Fitting and electrical connection
DANGER!Electrical shock when live parts aretouched.Electrical shocks can be fatal.Before working on the device,disconnect the power supply and coverup live parts in the workingenvironment.
Connecting and fitting the device
DANGER!When connecting the bus/extensionsand mains voltage wires in a sharedappliance box, the KNX bus line maycome into contact with the mainsvoltage.This endangers the safety of the entireKNX installation. People at remotedevices may also receive an electricshock.Do not place bus/extensions and mainsvoltage terminals in a sharedconnection compartment. Use anappliance box with a fixed partition wall(Figure 3) or separate boxes.
Figure 3
(4) Appliance box(5) Partition(6) Potential-free contacts, e.g. for window contact
or installation pushbuttons
Figure 4
Minimum spacing between the mains voltage andbus/extension wires: 4 mm (Figure 4).o Connect the load (Figure 5). Use the supplied
terminals. o Connect the device to KNX.o If necessary, connect potential-free contacts (6)
to inputs (Figure 2).o Install the device in the appliance box.
Figure 5
i In the as-delivered state, Inputs 1 and 2 operatethe Venetian blind output. Input 3 has nofunction.
Function of Inputs 1 and 2 in the as-deliveredstate
Input NO contact Blind
1 Press briefly Adjust slats Up/ Stop
1 Press for a longtime
Raising
2 Press briefly Adjust slatsDown / Stop
2 Press for a longtime
Lowering
Use terminals
Figure 6: Stripping length
o Strip 9 - 11 mm of the cable (Figure 6).
Figure 7: Connection of the fine-wire cable
o Push the terminal together on the side with thesquare opening and connect a fine-wire cable(Figure 7).
Figure 8: Connection of the single-stranded cable
o Push the single-stranded cable into the roundopening on the installation side up to the stop(Figure 8).
CommissioningLoad the address and the application softwareo Switch on the bus voltageo Assign physical addresses and load application
software into the device.o Note the physical address on the device label.
Appendix
Technical dataSupplyRated voltage AC 230 / 240 V ~Mains frequency 50 / 60 HzSwitching voltage AC 250 V~Ambient conditionsAmbient temperature -5 ... +45 °CStorage/transporttemperature
-25 ... +70 °C
Venetian blind outputContact type µSwitching current AC1 3 AMinimum switchingcurrent AC
100 mA
Motors 230 V 600 VAHeating outputOutput type Semi-conductor (Triac), εSwitching current 5 ... 25 mASwitch-on current max. 600 mA (2 sec)Number of drives peroutput
max. 2
Control cable and inputsControl cable(preterminated)
YY6x0.6
Input type Potential-freeTotal length of extensionunit cable
max. 5 m
Poll voltage, extensioninputs
approx. 5 V
Dimensions Ø×H 53×28 mmConnection mode Terminal (enclosed)Single stranded 1.0 ... 2.5 mm²KNXKNX medium TP 1Commissioning mode S-modeRated voltage KNX DC 21 ... 32 V SELVPower consumption KNX max. 240 mWConnection mode KNX Connection terminal on
control cable
Merten GmbH
Merten GmbHSolutions for intelligent buildingsService CenterFritz-Kotz-Strasse 8Industriegebiet Boming-WestD-51674 WiehlTelefon: +49 2261/702-204 Telefax: +49 2261/702-136 E-Mail: [email protected]: www.merten.com
If you have technical questions, please contactour InfoLine:Telefon: +49 1805 212581* oder +49 800 63783640 Telefax: +49 1805 212582* oder +49 800 63783630 E-Mail: [email protected]* fee required