IP-7900 7700 02 OM 補足版 EIP-7900/7700 Wide Format Solvent Inkjet Printer (hereafter simply...

IP-7900/7700　操作ガイド補足版 ( 英語版 )　表 1/4　背厚：6 mm

Read this User’s Guide carefully before use of this printer and handle it properly.After reading, keep it for later use.

E n h a n c e m e n t G u i d e 3D o c um e n t n um b e r

Wide Format Solvent Inkjet Printer

IP-7900/7700

U00121262500

U00121262500

IP-7900_7700_02_OM_補足版_E.indd 1 2010/07/30 10:56:31

IP-7900/7700 Wide Format Solvent Inkjet Printer Enhancement GuideDocuments Number U00121262500, First Edition, July 2010

Copyright © 2010 by Seiko I Infotech Inc.All rights reserved

Seiko I Infotech Inc. reserves the right to make changes without notice to the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical, arithmetic, or listing errors.

Please address any questions, comments, and suggestions to :

Seiko Instruments GmbH, French branch20 rue Jean Rostand, 91400 Orsay FranceTel: +33-1-60-19-35-41Fax: +33-1-60-19-35-17

Seiko Instruments USA Inc., Infotech Division2060 Wineridge Place, Suite A, Escondido,CA 92029, USATel : +1-760-781-5200Fax : +1-760-745-1195

Seiko I Infotech Inc.8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, JapanPhone : +81 43 211 1363Fax : +81 43 211 8709

This guide acknowledges the following trademarks :

is a trademark of Seiko Instruments Inc.All other trademarks are the properties of their respective companies.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive, is statutorily obliged to be affixed to the products.In each directive, the scope of directive to be applied to equipment is explicitly defined. Our company’s product IP-7900 conforms the EMC directive (2004/108/EC)) and low voltage directive (2006/95/EC).

Inquiry of CE mark:

Seiko Instruments Europe S.A.European Head Office20 rue Jean Rostand, 91400 Orsay FranceTel: +33-1-60-19-35-41Fax: +33-1-60-19-35-17



IP-7900/7700-02　操作ガイド補足版 ( 英語版 )　表 2/3　背厚：6 mm

IP-7900_7700_02_OM_補足版_E.indd 2 2010/07/30 10:56:32

3

Introduction

IP-7900/7700 Wide Format Solvent Inkjet Printer (hereafter simply called the Printer.) is equipped with built-in USB interface that adopts solvent ink and supports media of up to 104-inch width (IP-7700: 74-inch width).

IP-7900/7700 Wide Format Solvent Inkjet Printer “Enhancement Guide” explains the additional improvement and information to the documents below. So read the “Enhancement Guide” referring to them. - IP-7900-00/7700-00 Wide Format Solvent Inkjet Printer Basic Operation Guide (U00117679401, May 2010) - IP-7900/7700 Wide Format Solvent Inkjet Printer Advanced Operation Guide (U00117680501, May 2010) - IP-7900-02/7700-02 Wide Format Solvent Inkjet Printer Basic Operation Guide (U00120248800, May 2010) - IP-7900-02/-03/7700-02/-03 Wide Format Solvent Inkjet Printer Advanced Operation Guide (U00120250100, May 2010)

The Basic Operation Guide describes:

- The Printer’s features and main components

- Information required for the operation

- Basic operations to turn the Printer on and o� and to handle the media and ink system

To operate the Printer safely and properly, before starting the operation be sure to read the following. - Safety precautions - Delivery products - Manual legend (notation rules)

Keep this guide near the Printer so that you can quickly access it at any time.

IP-7900/7700 Wide Format Solvent Inkjet Printer Enhancement GuideDocuments Number U00121262500, First Edition, July 2010

Copyright © 2010 by Seiko I Infotech Inc.All rights reserved

Seiko I Infotech Inc. reserves the right to make changes without notice to the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical, arithmetic, or listing errors.

Please address any questions, comments, and suggestions to :

Seiko Instruments GmbH, French branch20 rue Jean Rostand, 91400 Orsay FranceTel: +33-1-60-19-35-41Fax: +33-1-60-19-35-17



This guide acknowledges the following trademarks :

is a trademark of Seiko Instruments Inc.All other trademarks are the properties of their respective companies.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive, is statutorily obliged to be affixed to the products.In each directive, the scope of directive to be applied to equipment is explicitly defined. Our company’s product IP-7900 conforms the EMC directive (2004/108/EC)) and low voltage directive (2006/95/EC).

Inquiry of CE mark:

Seiko Instruments Europe S.A.European Head Office20 rue Jean Rostand, 91400 Orsay FranceTel: +33-1-60-19-35-41Fax: +33-1-60-19-35-17



IP-7900/7700-02　操作ガイド補足版 ( 英語版 )　表 2/3　背厚：6 mm

IP-7900_7700_02_OM_補足版_E.indd 3 2010/07/30 10:56:33

4

The notational rules such as marks, keys, LCD, and LEDs used for explanation in this guide are as follows:

Marks

WARNING- Boxes marked with a "WARNING" describe points of caution for avoiding serious personal injury.

CAUTION- Boxes marked with a "CAUTION" describe points of caution for avoiding injury to yourself or damage

to the Printer.

TIP:

- This mark o� ers you the information to facilitate the Printer operation.

Reference markThis mark is followed by a reference section or page number.

Marginal indication for source document

The marginal indications guide you the document as the information source. Note that the description on the Enhancement Guide: - replaces the source document’s description; or - explains additionally on the source document’s description.

Table of contents

The table of contents contains two types of numbers: ones parenthesized, and others with a star. The parenthesized numbers indicate the page numbers to be referred on the source document, while the starred ones indicate the page numbers of the “Enhancement Guide.”

Manual legend (Notational rules)

IP-7900_7700_02_OM_補足版_E.indd 4 2010/07/30 10:56:35

5

IP-7900-00/7700-00 Basic Operation Guide

TABLE OF CONTENTS

Introduction (3)Safety precautions (7)General warning and cautions (7)Handling precautions (9)Components delivered with this product (12)Manual legend (Notational rules) (14)Operating conditions (17)

Introduction (18)

Appearance / Main components and their functions (18)Printer rear (supply side) (19)

Printer interior (20)

Operation panel (21)

Printer heater unit (21)

Online and o� ine (22)Online (22)

Offline (22)

Supported media (23)Vinyl (23)

Banner (23)

Mesh banner (23)

Backlit banner (FF) (23)

Solvent printing coated paper (23)

For your basic operation (24)

Precautions to prevent media jams (24)Basic operation for printing (26)Printing workflow overview (26)

Procedure to remove media roll from the Printer (44)Media at take-up side (44)

Media at supply side (46)

Procedure to remove scroller (scroller flange) from media roll (48)

To print on other media (50)To print on Vinyl, Mesh banner, Backlit banner (FF), or Solvent printing coated paper (50)

To take up media in LOOSE winding mode (52)

To perform double-sided printing (59)

Maintenance (64)

Daily maintenance (64)Check the wiper blade for contamination and replenish wiper cleaning liquid (66)

Clean the capping unit (67)

Replenish spittoon absorber liquid (69)

Check the waste ink bottle (70)

Clean the carriage (70)

Cleaning the madia edge guard (73)

Performing normal cleaning (74)

Print the nozzle print pattern (75)

Cleaning (76)Clean the exterior (76)

Clean the front cover and front paper guide (76)

Carriage cleaning (76)

After today’s operation (77)

When encountering a problem (82)

Check your problem (82)How to clear media jams (85)When an error message is displayed (86)Out of ink while printing (90)The media was skewed. (91)Warning messages 9Move the Printer (93)Replace a waste ink bottle (94)Install and replace an ink pack (96)Replace a spittoon case (98)Replace a wiper blade (100)

Appendix (102)

Basic speci� cations (102)Consumables (103)Options (105)Index (108)

IP-7900_7700_02_OM_補足版_E.indd 5 2010/07/30 10:57:00

6


TABLE OF CONTENTS

Introduction (3)Safety precautions (7)General warning and cautions (7)Handling precautions (8)Components delivered with this product (12)Manual legend (Notational rules) (14)Operating conditions (17)

Introduction (18)

Appearance / Main components and their functions (18)Printer rear (supply side) (18)

Printer interior (20)

Operation panel (21)

Printer heater unit (21)

Online and o� ine (22)Online (22)

Offline (22)

Supported media (23)Vinyl (23)

Banner (23)

Mesh banner (23)

Backlit banner (FF) (23)

Solvent printing coated paper (23)

For your basic operation (24)

Precautions to prevent media jams (25)Basic operation for printing (26)Printing workflow overview (26)

Procedure to remove media roll from the Printer (45)Media at take-up side (45)

Media at supply side (48)

Procedure to remove scroller flange from media roll (50)

To print on other media (53)To print on Vinyl, Mesh banner, Backlit banner (FF), or Solvent printing coated paper (53)

To take up media in LOOSE winding mode (54)

To perform double-sided printing (60)

Maintenance (64)

Daily maintenance (64)Check the wiper blade for contamination and replenish wiper cleaning liquid (66)

Clean the capping unit (67)

Replenish spittoon absorber liquid (69)

Check the waste ink bottle (70)

Clean the carriage (70)

Cleaning the madia edge guard (73)

Performing normal cleaning (74)

Print the nozzle print pattern (75)

Cleaning (76)Clean the exterior (76)

Clean the front cover and front paper guide (76)

Carriage cleaning (76)

After today’s operation (77)

When encountering a problem (82)

Check your problem (82)How to clear media jams (85)When an error message is displayed (86)Out of ink while printing (90)The media was skewed. (91)Warning messages 10Move the Printer (93)Replace a waste ink bottle (94)Install and replace an ink pack (96)Replace a spittoon case (98)Replace a wiper blade (100)

Appendix (102)

Basic speci� cations (102)Consumables (103)Options (105)Index (108)

IP-7900_7700_02_OM_補足版_E.indd 6 2010/07/30 10:57:25

7

IP-7900/7700 Advanced Operation Guide

TABLE OF CONTENTS

Introduction (3)Manual legend (Notational rules) (7)

To assist your Printer in operating effectively (8)

Turn the Printer o� (8)Service cleaning (9)

Head wash (14)

Charging the ink system after head wash (19)

Check the Printer status (22)Check the remaining ink level (22)

Check remaining media length (23)

Print reports on the Printer status. (23)

Check the USB connection status (24)

Check the firmware version on your Printer (25)

Check the total print distance (25)

Handle the media (26)Create a new media preset (26)

Select a preset media (28)

Minimize the right and left margins (28)

Solve media sticking problem (30)

Solve media lifting up problem (30)

Print on a thick media (31)

Change the automatic cleaning timing 11

Copy a preset media type to create a new one (33)

Feed or rewind media (34)

Move a print start position (nest function) (36)

Print on a cut-sheet media (37)

Solve skew in LOOSE winding mode 13

To change the Printer’s basic settings (40)Turn the audio warning beep off (40)

Update the system firmware (41)

Cleaning options (42)Perform cleaning only for the specified print head (42)

Manage the media advance compensation (44)Change media advance compensation (44)

Manage print modes (45)Troubleshoot print quality issues (46)The print is light. (46)

Missing dots are found at the beginning of printing. (46)

The media is curled or wrinkled. (47)

White stripes appear on the print. (48)

Edges of objects are blurred. (53)

A vertical barding appears at the print's edge. (54)

Different bandings appear on the print’s right and left. (55)

Clear missing dots (nozzle clogging) (56)Strong cleaning (56)

Fill the cap with ink (57)

Fill the cap with wiper cleaning liquid (58)

Switch between 4-color mode and 8-color mode (60)Adjust the heaters’ temperature (68)Procedure to set the heater temperature (68)

Display the heater control menu. (69)

Key operation in the heater control menu (69)

Finish displaying the heater control menu (69)

Set the heater preset temperature (70)

Select the standby time (71)

Smart pass technology 14

Adjust and calibrate the Printer (74)

Before adjustment and calibration (74)Procedure to set the smart pass technology [#IMAGE IMPROVE.] to off (74)

Procedures (75)Adjusting media advance compensation 16

Adjust print head position (78)

Adjust the nozzle positions at print head’s right and left (80)

Adjust bidirectional print positions (82)

Asjust the edge sensor position (87)

Adjust the print linkage after the automatic cleaning (Adjust the media back feed) (89)

Menu tree 22

Index (98)

IP-7900_7700_02_OM_補足版_E.indd 7 2010/07/30 10:57:51

8

TABLE OF CONTENTS

Introduction (3)Manual legend (Notational rules) (7)

To assist your Printer in operating effectively (8)

Turn the Printer o� (8)Service cleaning (9)

Head wash (14)

Charging the ink system after head wash (19)

Check the Printer status (22)Check the remaining ink level (22)

Check remaining media length (23)

Print reports on the Printer status. (23)

Check the USB connection status (24)

Check the firmware version on your Printer (25)

Check the total print distance (25)

Handle the media (26)Create a new media preset (26)

Select a preset media (28)

Minimize the right and left margins (28)

Solve media sticking problem (30)

Solve media lifting up problem (30)

Print on a thick media (31)

Change the automatic cleaning timing 11

Copy a preset media type to create a new one (33)

Feed or rewind media (34)

Move a print start position (nest function) (36)

Print on a cut-sheet media (37)

Solve skew in LOOSE winding mode 13

To change the Printer’s basic settings (40)Turn the audio warning beep off (40)

Update the system firmware (41)

Cleaning options (42)Perform cleaning only for the specified print head (42)

Manage the media advance compensation (44)Change media advance compensation (44)

Manage print modes (45)Troubleshoot print quality issues (46)The print is light. (46)

Missing dots are found at the beginning of printing. (46)

The media is curled or wrinkled. (47)

White stripes appear on the print. (48)

Edges of objects are blurred. (53)

A vertical barding appears at the print's edge. (54)

Different bandings appear on the print’s right and left. (55)

Clear missing dots (nozzle clogging) (56)Strong cleaning (56)

Fill the cap with ink (57)

Fill the cap with wiper cleaning liquid (58)

Switch between 4-color mode and 8-color mode (60)Adjust the heaters’ temperature (68)Procedure to set the heater temperature (68)

Display the heater control menu. (69)

Key operation in the heater control menu (69)

Finish displaying the heater control menu (69)

Set the heater preset temperature (70)

Select the standby time (71)

Smart pass technology 14

Adjust and calibrate the Printer (74)

Before adjustment and calibration (74)Procedure to set the smart pass technology [#IMAGE IMPROVE.] to off (74)

Procedures (75)Adjusting media advance compensation 16

Adjust print head position (78)

Adjust the nozzle positions at print head’s right and left (80)

Adjust bidirectional print positions (82)

Asjust the edge sensor position (87)

Adjust the print linkage after the automatic cleaning (Adjust the media back feed) (89)

Menu tree 22

Index (98)

IP-7900-02/7700-02 Advanced Operation Guide

IP-7900_7700_02_OM_補足版_E.indd 8 2010/07/30 10:58:17

9

IP-7900-00/7700-00 Basic Operation Guide Replaces the source document’s description

Warning messages

After the online printing, occasionally you may see one of the following messages appear on the operation panel display with the ERROR LED � ashing , which are warning messages. If so, follow the advice in the Recommendation column.

P E R F O R M D A I L YM A I N T E N A N C E N O W

Indication The daily maintenance (cap cleaning) is not performed.

Recommendation You are recommended to perform the daily maintenance. See “ Daily maintenance ” on the page 64 .

S E R V I C E N E E D E DC A L L S E R V I C E

Indication The supply tube pump assembly needs to be replaced.

Recommendation You are recommended to ask your service representative to replace it.

L O A D I N K P A C KC H A R G E I N K

Indication After the subcartridge’s initial ink charge to the ink system, the ink tray has not yet started the ink supply to the ink system.

Recommendation Set the ink packs to the ink box’s slots, and perform [#INK SUPPLY].

P E R F O R M P H R E C O V E R Y N O W

Indication Automatic cleaning is set to OFF, and the cleaning has not been performed for a prescribed period.

Recommendation You are recommended to perform the print head cleaning. See “ Performing normal cleaning ” on the page 76 .

The Ink LED blinks: Indication Ink is running out.

Recommendation Prepare a new ink pack. See “ Install and replace an ink pack ” on the page 96 .

IP-7900_7700_02_OM_補足版_E.indd 9 2010/07/30 10:58:43

10


Warning messages

After the online printing, occasionally you may see one of the following messages appear on the operation panel display with the ERROR LED � ashing , which are warning messages. If so, follow the advice in the Recommendation column.

P E R F O R M D A I L YM A I N T E N A N C E N O W

Indication The daily maintenance (cap cleaning) is not performed.

Recommendation You are recommended to perform the daily maintenance. See “ Daily maintenance ” on the page 64 .

S E R V I C E N E E D E DC A L L S E R V I C E

Indication The supply tube pump assembly needs to be replaced.

Recommendation You are recommended to ask your service representative to replace it.

L O A D I N K P A C KC H A R G E I N K

Indication After the subcartridge’s initial ink charge to the ink system, the ink tray has not yet started the ink supply to the ink system.

Recommendation Set the ink packs to the ink box’s slots, and perform [#INK SUPPLY].

P E R F O R M P H R E C O V E R Y N O W

Indication Automatic cleaning is set to OFF, and the cleaning has not been performed for a prescribed period.

Recommendation You are recommended to perform the print head cleaning. See “ Performing normal cleaning ” on the page 74 .

The Ink LED blinks: Indication Ink is running out.

Recommendation Prepare a new ink pack. See “ Install and replace an ink pack ” on the page 96 .

Replaces the source document’s description

IP-7900_7700_02_OM_補足版_E.indd 10 2010/07/30 10:59:07

11

IP-7900/7700 or IP-7900-02/7700-02 Advanced Operation Guide

Change the automatic cleaning timing

To ensure the print heads’ proper condition, the Printer performs the automatic cleaning. The cleaning mode can be speci� ed depending on the preset media. Select the DURING PRINT or DURING PRINT2 depending on the media characteristics.

Based on the past print operation history, the Printer performs the automatic cleaning: - On starting and completing the print operation; and - During the print operationWhen the Printer performs the cleaning during the print operation, the cleaning is started only after completing the current band’ s print.This mode is recommended when printing on the media subject to the heater temperature, for example, on Vinyl.After the cleaning, the Printer starts the rest of the interrupted print job.Some media shows misalignment at the linkage of the prints before and after the cleaning. In such a case, START & END or DURING PRINT2 is recommended.

Based on the past print operation history, the Printer performs the automatic cleaning on starting and completing the print operation.Note that the automatic cleaning is not performed during the print operation.

Based on the past print operation history, the Printer performs the automatic cleaning: - On starting and completing the print operation; and - During the print operationWhen the Printer performs the cleaning during the print operation, the cleaning is started by suspending the current band’ s print.This mode is recommended when printing on the media less subjected to the heater temperature, for example, on Banner.After the cleaning, the Printer starts the rest of the interrupted print job.This mode shows less misalignment at the linkage than the DURING PRINT. However, the hue after the cleaning may be di�erent from the one before the cleaning.

START & END

DURING PRINT

DURING PRINT2

Current print band

On starting and completing the printer operation, the Printer does not perform the automatic cleaning, but only after filling the cap with ink (fillcap) the Printer performs it.Note that the Printer never performs the automatic cleaning for ensuring the print heads’ good condition. So, at a nozzle clogging, manually perform the normal cleaning.

OFF

Correct withthe BACK ADJUST VAL.

CleaningCleaning

The procedure to change the automatic cleaning timing is explained as follows, taking the procedure to select the automatic cleaning DURING PRINT for the preset media 1 as example.

1 I N K M E D I A R E G M E D I A M . A D V

Set the Printer to o� ine state and press the key.


IP-7900_7700_02_OM_補足版_E.indd 11 2010/07/30 10:59:32

12

2 # S E L E C T M E D I A> 0 1 : P A P E R ✻

• • •

With the key, scroll to [#PH CLEANING].

3 # P H C L E A N I N G> 0 1 : S T A R T & E N D

Press the key.

4 # P H C L E A N I N G✻ 0 1 : S T A R T & E N D

Press the key.

5 # P H C L E A N I N G✻ 0 1 : D U R I N G P R I N T

# P H C L E A N I N G> 0 1 : D U R I N G P R I N T

Press the key.

IP-7900_7700_02_OM_補足版_E.indd 12 2010/07/30 10:59:57

13


Solve skew in LOOSE winding mode

1 Tension bar hook

Tension bar

Hook the tension bar to the tension bar hook beforehand.

2 Close the tension bar guide’s cover.Close the cover, and � x the cover by fastening the knob screw.

3 Load the media on the Printer.

For the procedure, see the Basic Operation Guide "To take up media in LOOSE winding mode ."

4 Place the tension bar with gear on the closed tension bar guide.Place the tension bar carefully to prevent the tension bar with gear from being dropped.

LOOSE winding mode

Supply-side tension bar

Tension bar with gearMedia

5 Input the data in the software RIP.

IP-7900_7700_02_OM_補足版_E.indd 13 2010/07/30 11:00:25

14


With inkjet printers, a horizontal banding may appear between the bands, which are the areas printed by one scan. This symptom is called as banding.The banding is caused mainly by setting the media advance compensation improperly. With the proper compensation, the bands are linked without gap. However, with the larger compensation the bands are linked with gaps, showing white lines, while with the smaller one the bands overlap, showing black lines.The banding is also caused in the following cases.- The ink dries so slowly.- The media advance changes considerably depending on the print head scan.

A band of print

A band of print

A band of print

A band of print

Print head Print head

A band of print

A band of print

Print head

Correct media advance White banding at incorrect media advance

The bands’ gap shows a white banding.

The bands’ gap shows a white banding.

The bands’ overlap shows a black banding.

The bands’ overlap shows a black banding.

Black banding at incorrect media advance

The Smart Pass Technology is the function to reduce this banding problem.With the Printer’s operation menu, this function is available by selecting the LOW, MEDIUM, HIGH, FINE GRAIN, or HIGH, LESS SPRAY at "#IMAGE IMPROVE" of MEDIA REG MENU.With Smart Pass Technology, the bands are printed with overlapping even when the media advance compensation is proper. In the LOW, the overlapping part is processed with the SIIT’s unique algorithm so that the part is not notable where the di� erence between the overlapping part and the rest are minimized.The modes MEDIUM, HIGH, FINE GRAIN, and HIGH, LESS SPRAY enlarged the overlapping parts and added the function to reduce the color density irregularities and white lines. This function allows the print performance with higher quality and more stabilization than the previous ones.

NOTE

(1) In the LOW, with some print data, the overlapping part is light or blurred. Select the MEDIUM, HIGH, FINE GRAIN, or HIGH, LESS SPRAY to reduce this symptom.

(2) In the HIGH, LESS SPRAY, the carriage speed is low.

Smart pass technology

A band of print

Print head

Smart pass technology: ON


IP-7900_7700_02_OM_補足版_E.indd 14 2010/07/30 11:00:53

15

IMAGE IMPROVE DescriptionTolerance for

media advance misalignment

Remark

OFF Banding is not reduced. None* Even with the accurate media advance, the slippery media may show banding.

LOW Banding is reduced. Small Even if the media advance is not accurately correct, the modes LOW, MEDIUM, HIGH, FINE GRAIN, and HIGH, LESS SPRAY show the banding-free printout. The modes also reduce the slight variation even with the slippery media. However, note that the printout is defective if the media advance misalignment exceeds the tolerance. So, to some extent, adjust the media advance compensation.

MEDIUM Banding is reduced. Select this mode if the image quality is not improved with the LOW.

Medium

HIGH, FINE GRAIN Banding is reduced. Select this mode if the image quality is not improved with the LOW and MEDIUM.

Large

HIGH, LESS SPRAY Banding is reduced. Select this mode to improve the problems below:- Bleeding is found; or- The image edge is not sharpened. As a result, the image is soft-focused.

Small

* Set the value accurately.

IP-7900

Print modeIMAGE IMPROVE *1

OFF LOW MEDIUM HIGH, FINE GRAIN HIGH, LESS SPRAY

DRAFT1 50m2/h (100m2/h) 46m2/h (93m2/h) 39m2/h (78m2/h) 28m2/h (56m2/h) *3 (*3)

FINE DRAFT1 39m2/h (78m2/h) 36m2/h (72m2/h) 24m2/h (56m2/h) 18m2/h (36m2/h) *3 (*3)

NORMAL1 30m2/h (60m2/h) 27m2/h (55m2/h) 19m2/h (38m2/h) 13m2/h (26m2/h) 13m2/h (26m2/h)


QUALITY 13m2/h (26m2/h) 12m2/h (24m2/h) 8m2/h (16m2/h) 7m2/h (14m2/h) 7m2/h (14m2/h)

DENSITY2 13m2/h (26m2/h) 12m2/h (24m2/h) 8m2/h (16m2/h) 7m2/h (14m2/h) 7m2/h (14m2/h)

IP-7700

Print modeIMAGE IMPROVE *2

OFF LOW MEDIUM HIGH, FINE GRAIN HIGH, LESS SPRAY

DRAFT1 50m2/h (100m2/h) 46m2/h (93m2/h) 34m2/h (68m2/h) 25m2/h (50m2/h) *3 (*3)

FINE DRAFT1 36m2/h (72m2/h) 33m2/h (67m2/h) 22m2/h (50m2/h) 16m2/h (32m2/h) *3 (*3)



QUALITY 12m2/h (24m2/h) 11m2/h (22m2/h) 7m2/h (14m2/h) 5m2/h (10m2/h) 5m2/h (10m2/h)

DENSITY2 12m2/h (24m2/h) 11m2/h (22m2/h) 7m2/h (14m2/h) 5m2/h (10m2/h) 5m2/h (10m2/h)

*1 The print speeds above are listed on the condition below:

- The Printer prints on the 2642mm (104 inches) roll media from its leftmost position to the rightmost position at 8-color print mode.

- The print speeds in brackets were measured on the same condition with 8-color print mode switched to 4-color print mode.

Currently, the 4-color print speeds with the modes MEDIUM, and HIGH, FINE GRAIN are under development.

*2 The print speeds above are listed on the condition below:- The Printer prints on the 1900mm (74 inches) roll media from its leftmost position to the rightmost position at 8-color print mode.

- The print speeds in brackets were measured on the same condition with 8-color print mode switched to 4-color print mode.

Currently, the 4-color print speeds with the modes MEDIUM, and HIGH, FINE GRAIN are under development.

*3 With DRAFT1 or FINE DRAFT1 selected, the HIGH, LESS SPRAY is not supported . When the HIGH, LESS SPRAY is selected, the Printer identi� es it as the HIGH, FINE GRAIN.

IP-7900_7700_02_OM_補足版_E.indd 15 2010/07/30 11:01:19

16


Procedures

Adjusting media advance compensation

Compensate the media advance adjustment value with:- [SIMPLE] media advance adjustment pattern; or- [ROUGH] and [DETAIL] media advance adjustment patternThe [SIMPLE] media advance adjustment pattern relatively reduces the media amount required to print the adjustment pattern, while [ROUGH] and [DETAIL] media advance adjustment patterns assist you to compensate the media advance adjustment value more accurately.If you intend to change the media advance compensation during the print, see the procedure on the page 44 .

With the Smart Pass Technology…

- Select [SIMPLE] so that you can change the media advance compensationwhile the Printer prints the media advance adjustment pattern in the mode set at "#IMAGE IMPROVE" of MEDIA REG MENU.

With [ROUGH] and [DETAIL] media advance adjustment pattern, the Printer always prints the media advance adjustment pattern in the OFF mode of "#IMAGE IMPROVE."

The factors that change the media advance compensations are as follows.

- Change the print mode- Change the pressure with the pressure control know.- Print with/without the take-up reel unit- Change the media type- Change the media advance path

Compensate the media advance with SIMPLE media advance adjustment patternTo compensate the media advance, determine the adjustment value with the SIMPLE media advance adjustment pattern. The length of one SIMPLE media advance adjustment pattern is 2-5mm depending on the print mode.

■ Work� ow

Step1 Step2

Print [SIMPLE] adjustment pattern.

While the Printer prints the media advance adjustment pattern, adjust the media advance adjustment value

by pressing the or key.

Completed

■ Procedure

STEP 1 Print [SIMPLE] adjustment pattern

1 Set media longer than 4 m. Load the media on the same condition as for the actual printing


IP-7900_7700_02_OM_補足版_E.indd 16 2010/07/30 11:01:44

17



3 # M E D I A A D V P R I N T> S I M P L E ( N O R M A L 1 )> S I M P L E ( N O R M A L 1 )

Print mode

With the or key, select [SIMPLE]

print mode, and press the key.

Select the print mode to be used normally for the media to set the media advance compensation.

For details of print mode, refer to P. 45 .

If the print mode, [DENSITY2] is selected...

- To obtain the media advance compensation in DENSITY2 mode, apply the media advance adjustment patterns, SIMPLE(QUALITY).

4 # M E D I A A D V P R I N T✻ O K ?

Press the key.Then the media advance adjustment pattern [SIMPLE] is printed in the selected print mode.

# M E D I A A D V P R I N T✻ E X E C U T I N G

To cancel printing of media advance adjustment pattern, press the CANCEL key.

STEP 2 While the Printer prints the media advance adjustment pattern, adjust the media advance

adjustment value by pressing the or key.

1 # M E D I A A D V P R I N T✻ E X E C U T I N G

,

Adjusting media advance compensation

With the or key, change the media advance compensation.

M E D I A A D V : 0 9 9 . 8 0 %✻ 0 9 9 . 8 0 %

The value at the start of printing

The value is incremented or decremented by 0.01%

with the or key.

0 9 9 . 8 0 %M E D I A A D V : 0 9 9 . 8 0 %


When no key is operated for three seconds, the display returns to the original one.

IP-7900_7700_02_OM_補足版_E.indd 17 2010/07/30 11:02:14

18

How to analyze the media advance adjustment pattern [SIMPLE]

Analyzing the SIMPLE media advance adjustment pattern is explained using an example of 8-color mode printout.

In case of small media advance compensation

In case of appropriate mediaadvance compensation

In case of large media advance compensation

In Lc, Lm, Gy, and Lg, the horizontal lines and the stripe bar’s bottom are misaligned downward, because the adjustment value is smaller.

All horizontal lines are aligned in one line, and the color stripe bar’s bottom is also aligned in one line when the adjustment value is proper.

In Lc, Lm, Gy, and Lg, the horizontal lines and the stripe bar’s bottom are misaligned upward, because the adjustment value is larger.

Media advance direction

2 Repeat the procedure from STEP 1-3 to STEP 2-1 to obtain an appropriatemedia advance compensation.

3 # M E D I A A D V P R I N T> S I M P L E ( N O R M A L 1 )

CANCEL

I N K M E D I A R E G M E D I A M . A D V

Compensate the media advance with [ROUGH] and [DETAIL] media advance adjustment pattern

Obtain your initial media advance compensation with [ROUGH] media advance adjustment pattern, and then determine the � nal media advance compensation with [DETAIL] media advance adjustment pattern. Each of [ROUGH] and [DETAIL] prints approx. 90 cm media advance adjustment pattern.

■ Work� ow

Step1 Step3Step2

Step4

Select a rough media advance

compensation from the print result.

Review the pattern to determine the final

compesnsation

Print [ROUGH] adjustment pattern.

Enter the media advance

compensation.

Enter the media advance compensation.

Print [DETAIL] adjustment pattern.

Completed

IP-7900_7700_02_OM_補足版_E.indd 18 2010/07/30 11:02:39

19

■ Procedure

STEP 1 Print [ROUGH] adjustment pattern

1 Set media longer than 4 m. Load the media on the same condition as for the actual printing



3 # M E D I A A D V P R I N T> R O U G H ( N O R M A L 1 )

With the or key, select [ROUGH]

print mode, and press the key.

Select the print mode to be used normally for the media to set the media advance compensation.

For details of print mode, refer to P. 45 .

If the print mode, [DENSITY2] is selected...

- To obtain the media advance compensation in DENSITY2 mode, apply the media advance adjustment patterns, ROUGH(QUALITY) or DETAIL(QUALITY).


Press the key.Then the media advance adjustment pattern [ROUGH] is printed in the selected print mode.


To cancel printing of media advance adjustment pattern, press the CANCEL key.

5 Select a rough media advance compensation from the print result.

Five patterns are printed with 0.5% increments within a range of 99.00% to 101.00%. Select a rough media advance compensation from them.

IP-7900_7700_02_OM_補足版_E.indd 19 2010/07/30 11:03:05

20

How to analyze the media advance adjustment pattern

Analyzing the media advance adjustment pattern is explained using an example of black (K) color.

In case of small media advance compensation

In case of appropriate mediaadvance compensation

In case of large media advance compensation

When observing the horizontallines, if the splices of paths are overlapped (dense), the media advance compensation is small.

When the splices of paths are not overlapped and even, the media advance compensation isappropriate.

When the splices of paths are separated (light), the media advance compensation is large.

99.00% 100.25% 101.00%

STEP 2 Enter the media advance compensation.

1 # M E D I A A D V V A L U E# B a n n e r > 1 0 0 . 0 0 %

Press the key.

2 # M E D I A A D V V A L U E# B a n n e r ✻ 1 0 0 . 0 0 %

, , ,

Enter the media advance compensation.Align the digit with the or key and set the value

with the or key.


Press the key.


Press the key.

STEP 3 Print [DETAIL] adjustment pattern


,

Select the detail print mode with the or key.

Select the same print mode as for [ROUGH].

IP-7900_7700_02_OM_補足版_E.indd 20 2010/07/30 11:03:30

21

2 # M E D I A A D V P R I N T> D E T A I L ( N O R M A L 1 )

Press the key.


Press the key.Then the media advance adjustment pattern [DETAIL] is printed in the selected print mode.

4 # M E D I A A D V P R I N T✻ E X E C U T I N G

5 Select the detail media advance compensation from the print result.

Five patterns are printed for the entered rough media advance compensation with 0.06% increments within a range of -0.12% to +0.12%. Select an appropriate media advance compensation from them.

STEP 4 Enter the media advance compensation.


Press the key.


Press the key.


, , ,

Enter the determined media advance compensation.Align the digit with the or key and set the value

with the or key.


Press the key.


The operation is completed.Press the CANCEL key to return to the o� ine state.

IP-7900_7700_02_OM_補足版_E.indd 21 2010/07/30 11:03:57

22

Menu tree

01 to 20

6-digit character input (codes, alphanumerics, katakana characters, etc.)

097.00 106.00

>01:YES>01:NO

>01:FWD ONLY>01:BACK & FWD1>01:BACK & FWD2

① ② ③

M E N U

�I N K M E D I A R E G�

�M E D I A M . A D V �

INK MENU

MEDIA MENU

MEDIA REG MENU

X X X I N K L E V E L Z Z Z %

D A T E : Y Y / M M / D D

R O L L ( P A P E R )

X X X m m

R E M A I N I N G M E D I A

Z Z Z m

S H E E T ( P A P E R )

Y Y Y Y m m

N E S T ( P A P E R )

Y Y Y Y m m

Toggle display

Toggle display

Toggle display


Z Z Z m

F A C E ( P A P E R )

Y Y Y Y m m

B A C K ( P A P E R )

Y Y Y Y m m


Z Z Z m

# S E L E C T M E D I A

> 0 1 : P A P E R

# R E N A M E M E D I A

> 0 1 : P A P E R

# M E D I A A D V V A L U E

> 0 1 : 0 9 9 . 8 0 %

# M E D I A A D V M O D E

> 0 1 : F W D O N L Y

# U S E E D G E G U A R D

> 0 1 : Y E S

Menu tree

01 to 20

6-digit character input (codes, alphanumerics,katakana characters, etc.)

097.00 106.00

>01:YES>01:NO

>01:FWD ONLY>01:BACK & FWD1>01:BACK & FWD2

① ② ③

M E N U

�I N K M E D I A R E G�

�M E D I A M . A D V �

INK MENU

MEDIA MENU

MEDIA REG MENU

X X X I N K L E V E L Z Z Z %

D A T E : Y Y / M M / D D

R O L L ( P A P E R )

X X X m m


Z Z Z m

S H E E T ( P A P E R )

Y Y Y Y m m

N E S T ( P A P E R )

Y Y Y Y m m

Toggle displaToggle displaT y




Z Z Z m

F A C E ( P A P E R )

Y Y Y Y m m

B A C K ( P A P E R )

Y Y Y Y m m


Z Z Z m

# S E L E C T M E D I A

> 0 1 : P A P E R

# R E N A M E M E D I A

> 0 1 : P A P E R


> 0 1 : 0 9 9 . 8 0 %

# M E D I A A D V M O D E

> 0 1 : F W D O N L Y

# U S E E D G E G U A R D

> 0 1 : Y E S

IP-7900/7700 or IP-7900-02/7700-02 Advanced Operation Guide Replaces the source document’s description

IP-7900_7700_02_OM_補足版_E.indd 22 2010/07/30 11:04:49

23

① ② ③

④

15°C to 70°C59°F to 158°F

15°C to 55°C59°F to 131°F

15°C to 55°C59°F to 131°F

>01:ON>01:OFF

>01:LOW>01:MEDIUM>01:HIGH, FINE GRAIN>01:HIGH, LESS SPRAY>01:OFF>01:START & END>01:DURING PRINT>01:DURING PRINT2>01:OFF

±2000 pulses (Unit: Approx. 2.5 μm)

0000 to 9999

1 to 99

±, -32 to +31

±, -32 to +31

±, -32 to +31

-0.3 to +1.0 (Unit: 0.1 mm)

# M E D I A B A C K M O D E

> 0 1 : B A C K & F W D

# P R E H E A T E R T

> 0 1 : � � ° C

# C O L O R S T R I P E

> 0 1 : O N

# B I D I R A D J 2 L P A P E R

> 0 1 : + 0 0

# I M A G E I M P R O V E .

> 0 1 : O N

# P H C L E A N I N G

> 0 1 : S T A R T & E N D

# B A C K A D J U S T V A L

> 0 1 : + 0 0 0 0 P U L S E

# P H H E I G H T V A L

> 0 1 : + 0 . 0 m m

# P H R E S T P E R I O D

> 0 1 : 0 0 0 0 C Y C L E S

# P H R E S T T I M E

> 0 1 : 1 0 s e c

# A F T E R H E A T E R T

> 0 1 : � � ° C

# P R I N T H E A T E R T

> 0 1 : � � ° C

# B I D I R A D J 2 R P A P E R

> 0 1 : + 0 0


> 0 1 : + 0 0

# S U C T I O N F A N L E V E L

> 0 1 : N O R M A L

>01:BACK & FWD>01:FWD ONLY

>01:HIGH>01:NORMAL>01:LOW>01:OFF

IP-7900_7700_02_OM_補足版_E.indd 23 2010/07/30 11:05:12

24

① ② ④

＃メテ゛ィアサ゛ンリョウ＞０１：ＹＹＹｍ

＃メテ゛ィアサクシ゛ョ＞０２：ＴＹＰＥ０２　ＯＫ？

＃ハ゜ラメータ　コヒ゜ーモト＞０１

＃ハ゜ラメータ　コヒ゜ーサキ＞０１→０２＊

＃オクリチョウセイハ゜ターン＞ラフ（ヒョウシ゛ュン）

＃オクリホセイチ＃ＰＡＰＥＲ　＞１００．００％

＃モト゛シチョウセイハ゜ターン＞ヒョウシ゛ュン

＃モト゛シホセイチ＃ＰＡＰＥＲ　＞＋００００ハ゜ルス

＃オウフクホセイチ４　Ｒ　ＰＡＰＥＲ＞０１：＋００

＃オウフクホセイチ３　Ｒ　ＰＡＰＥＲ＞０１：＋００

＃オウフクホセイチ４　Ｌ　ＰＡＰＥＲ＞０１：＋００

±, -32 to +31

±, -32 to +31

±, -32 to +31

0 to 999m0 to 3278ft

01 to 20

01 to 20

97.00 to 106.00%

>NORMAL1 >QUALITY>DRAFT1>FINE DRAFT>NORMAL2

±2000 pulses (Unit: Approx. 2.5 μm)

>SIMPLE(DRAFT1)>SIMPLE(FINE DRAFT)>SIMPLE(NORMAL1)>SIMPLE(NORMAL2)>SIMPLE(QUALITY)>ROUGH(DRAFT1)>ROUGH(FINE DRAFT)>ROUGH(NORMAL1)>ROUGH(NORMAL2)>ROUGH(QUALITY)>DETAIL(DRAFT1)>DETAIL(FINE DRAFT)>DETAIL(NORMAL1)>DETAIL(NORMAL2)>DETAIL(QUALITY)

# R E M A I N I N G M E D I A

> 0 1 : Y Y Y m

# D E L E T E M E D I A

> 0 2 : T Y P E 0 2 O K ?

# C O P Y M E D I A

> 0 1

# P A S T E M E D I A

> 0 1�0 2 *

# M E D I A A D V P R I N T

> S I M P L E ( D R A F T 1 )


# P A P E R > 0 9 9 . 8 1 %

# B A C K A D J P R I N T

> N O R M A L 1

# B A C K A D J U S T V A L

# P A P E R > + 0 0 0 0 P


> 0 1 : + 0 0


> 0 1 : + 0 0


> 0 1 : + 0 0

M.ADV MENU

IP-7900_7700_02_OM_補足版_E.indd 24 2010/07/30 11:05:39

25

①

⑦ ⑧

＃キャッフ°クリーニンク゛＞

＃サーヒ゛ス＞サーヒ゛スクリーン

�ファンクション　　　　　　　　　システム��メカチョウセイ　　　　　　　　　　ヒータ�

>NOZZLE PRINT>ADJUSTMENT & CHECK>ADJUST PH POS>ADJUST PH R/L>BIDIRECTION1>BIDIRECTION2>BIDIRECTION3>BIDIRECTION4>CHECK EDGE SENSOR>CHECK NOZZLE>CHECK BIDIR1>CHECK BIDIR2>CHECK BIDIR3>CHECK BIDIR4

�ハックフーィト　　　　　　　　　フィート �

�クリーニンク　　　　　　　　　サーヒス�

M E N U

>NORMAL>STRONG

>STORE INK SYS>CLEAN INK SYS>INITIAL CHARGE>CHARGE(INKPACK)>CHARGE CAP CL>PH CLEANING

R E W I N D I N G M E D I A

# P H R E C O V E R Y

> N O R M A L

F E E D I N G M E D I A

REWIND MENU

PH.REC MENU

FORM FEED MENU

PH.MAIN MENU

�R E W I N D F O R M F E E D�

�P H . R E C P H . M A I N �

�P R I N T E R S E T U P�

�A D J U S T H E A T E R �

# C A P C L E A N I N G

>

# I N K S Y S T E M O P T

> S T O R E I N K S Y S

# C O L O R C H A N G E ( 8 - > 4 )

>

# R E S E A T P R I N T H E A D

>

# W A S H P R I N T H E A D S

>

PRINTER MENU

ADJUST MENU

# E R R O R L O G P R I N T

>

# C O N F I G P R I N T

>

# H I S T O R Y P R I N T

>

# T E S T P R I N T S

> N O Z Z L E P R I N T

IP-7900_7700_02_OM_補足版_E.indd 25 2010/07/30 11:06:03

26

⑦

＃タイムソ゛ーン（ＹＹ／ＭＭ／ＤＤ）＊ｙｙ／ｍｍ／ｄｄ　ｈｈ：ｍｉ　＋ｘｘ

＃ＬＡＮＧＵＡＧＥ＞ＪＡＰＡＮＥＳＥ

＃ナカ゛サタンイ＞ミリ

⑨

⑧

＃オウフクホセイチ３　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ３　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ４　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ４　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃エッシ゛センサイチホセイチ＞＋０．０ｍｍ

＃オウフクホセイチ２　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ２　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

-5.0 to +5.0 mm

>ENGLISH>FRENCH>ITALIAN>GERMAN>SPANISH>PORTUGUESE>JAPANESE

-12 to +12

>MILLIMETER>INCH

＃ヘット゛イチホセイチ＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ１　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃ヘット゛サユウホセイチ＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ１　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

# P H T O P H V A L

# Y 1 > + 0 0


# Y 1 > + 0 0

# P H R / L A D J V A L

# Y 1 > + 0 0


# Y 1 > + 0 0

# T I M E Z O N E ( G M T + )

> Y Y / M M / D D H H : M M + 0 0

# L A N G U A G E

> E N G L I S H

# L E N G T H U N I T S

> M I L L I M E T E R


# Y Y > + 0 0


# Y Y > + 0 0


# Y Y Y > + 0 0


# Y Y Y > + 0 0

# E D G E S E N S O R A D J V A L

> + 0 . 0 m m


# Y Y > + 0 0


# Y Y > + 0 0

SETUP MENU

IP-7900_7700_02_OM_補足版_E.indd 26 2010/07/30 11:06:27

27

⑦

＃タイムソ゛ーン（ＹＹ／ＭＭ／ＤＤ）＊ｙｙ／ｍｍ／ｄｄ　ｈｈ：ｍｉ　＋ｘｘ

＃ＬＡＮＧＵＡＧＥ＞ＪＡＰＡＮＥＳＥ

＃ナカ゛サタンイ＞ミリ

⑨

⑧

＃オウフクホセイチ３　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ３　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ４　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ４　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃エッシ゛センサイチホセイチ＞＋０．０ｍｍ

＃オウフクホセイチ２　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ２　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

±, -32 to +31

-5.0 to +5.0 mm

>ENGLISH>FRENCH>ITALIAN>GERMAN>SPANISH>PORTUGUESE>JAPANESE

-12 to +12

>MILLIMETER>INCH

＃ヘット゛イチホセイチ＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ１　Ｌ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

＃ヘット゛サユウホセイチ＃Ｙ１　　　　　　＞＋００

＃オウフクホセイチ１　Ｒ　ＰＡＰＥＲ　＃Ｙ１　　　　　　＞＋００

# P H T O P H V A L

# Y 1 > + 0 0


# Y 1 > + 0 0

# P H R / L A D J V A L

# Y 1 > + 0 0


# Y 1 > + 0 0

# T I M E Z O N E ( G M T + )

> Y Y / M M / D D H H : M M + 0 0

# L A N G U A G E

> E N G L I S H

# L E N G T H U N I T S

> M I L L I M E T E R


# Y Y > + 0 0


# Y Y > + 0 0


# Y Y Y > + 0 0


# Y Y Y > + 0 0

# E D G E S E N S O R A D J V A L

> + 0 . 0 m m


# Y Y > + 0 0


# Y Y > + 0 0

SETUP MENU

⑦ ⑨

＃ＵＳＢ　スヒﾟート゛＊ＨＩＧＨ－ＳＰＥＥＤ

＃ＵＳＢアト゛レス＊０００

＃ショキセッテイ＞

＃アッフﾟテ゛ート＞

＃タ゛ウンロート゛＞

＃シ゛ャムケンシュツカント゛＞キョウ（テ゛フォルト）

＃スタンハ゛イシ゛カン＞３０フン

＃ＨＣＢハ゛ーシ゛ョン＊ＸＸ＿ＹＹＺ

＃ＢＴＣハ゛ーシ゛ョン＊ＸＸＸ

＃Ｆ／Ｗハ゛ーシ゛ョン＊Ｘ．ＸＸ＿ＹＹ

P.3-62

＃ＩＰＢハ゛ーシ゛ョン＊ＸＸ＿ＹＹＺ

P.3-62

＃ＡＣＴハ゛ーシ゛ョン＊ＸＸ＿ＹＹＺ

P.3-62


P.3-62


P.3-62


P.3-62




HIGH-SPEEDFULL-SPEED

>HIGH(DEFAULT>LOW

>NONE>30min>60min>120min>CONTINUOUS

＃オント゛タンイ＞セッシ

＃ケイコクオン（キャッフ゜オーフ゜ン）＞オン

＃ケイコクオン（ＴＵＲタイムアウト）＞オン

＃ケイコクオン（インクエラー）＞オン

＃ＢＯＯＴハ゛ーシ゛ョン＊Ｘ．ＸＸ

>CENTIGRADE>FAHRENHEIT

>ON>OFF

>ON>OFF

>ON>OFF

000 to 255

# T E M P E R A T U R E U N I T S

> C E N T I G R A D E

# B E E P ( U N C A P C A R R I )

> O N

# B E E P ( T U R T I M E O U T )

> O N

# B E E P ( I N K E R R O R )

> O N

# B O O T V E R S I O N

* X . X X

# U S B S P E E D

* H I G H - S P E E D

# U S B A D D R E S S

* X X X

# F A C T O R Y D E F A U L T

>

# P R I N T E R F W U P G R A D E

>

# D O W N L O A D

>

# J A M S E N S I T I V I T Y

> H I G H ( D E F A U L T )

# H E A T E R S T A N D B Y T I M E

> 3 0 m i n

# C A R R I A G E P C A V E R

* X X X X X

# B T C V E R

* X X X

# P R I N T E R F W V E R

* X . X X _ Y Y

# M A I N P C A V E R

* X X X X X

# A C T P C A V E R

* X . X X

HEATER MENU

IP-7900_7700_02_OM_補足版_E.indd 27 2010/07/30 11:06:50

IP-7900_7700_02_OM_補足版_E.indd 28 2010/07/30 11:06:50

IP-7900 7700 02 OM 補足版 EIP-7900/7700 Wide Format Solvent Inkjet Printer (hereafter simply...

Documents

Transcript of IP-7900 7700 02 OM 補足版 EIP-7900/7700 Wide Format Solvent Inkjet Printer (hereafter simply...