INTERRUPTS OF 8086 MICROPROCESSOR

39

description

The Presentation Contains Information on:- *INTERRUPTS *TYPES(SOFTWARE AND HARDWARE) *PURPOSES *INTERRUPT VECTOR TABLE *TYPE 0,1,2,.....18

Transcript of INTERRUPTS OF 8086 MICROPROCESSOR

Page 1: INTERRUPTS OF 8086 MICROPROCESSOR
Page 2: INTERRUPTS OF 8086 MICROPROCESSOR
Page 3: INTERRUPTS OF 8086 MICROPROCESSOR

• An Interrupt is either a Hardware generated CALL (externally derived from a hardware signal)

OR• A Software-generated CALL

(internally derived from the execution of an instruction or by some other internal event

Page 4: INTERRUPTS OF 8086 MICROPROCESSOR

An interrupt is used to cause a temporary halt in the execution of program.

The meaning of ‘interrupts’ is to break the sequence of operation.

While the Microprocessor is executing a program, an ‘interrupt’ breaks the normal sequence of execution of instructions, diverts its execution to some other program called Interrupt Service Routine (ISR).

• After executing ISR, IRET returns the control back again to the main program. Interrupt processing is an alternative to polling.

Page 5: INTERRUPTS OF 8086 MICROPROCESSOR

The keyboard controller can hold only a single keystroke. Therefore, the keyboard controller must be freed before the next keystroke arrives. The keystroke is passed to the CPU by putting it in the keyboard buffer. So, the keyboard controller keeps on passing the keystroke input to the CPU, but how does the CPU attend to it? The CPU is not at the disposal of the keyboard controller; it is usually busy doing several other operations. So, we need some mechanism to indicate to the CPU that a keystroke has arrived. How is this done? There are two approaches to making sure that the CPU pays attention:

Page 6: INTERRUPTS OF 8086 MICROPROCESSOR

The CPU executes other program, as soon as a key is pressed, the Keyboard generates an interrupt. The CPU will response to the interrupt – read the data. After that returns to the original program. So by proper use of interrupt, the CPU can serve many devices at the “same time”

Page 7: INTERRUPTS OF 8086 MICROPROCESSOR

The Purpose of Interrupts...

Page 8: INTERRUPTS OF 8086 MICROPROCESSOR

Interrupts are useful when interfacing I/O devices at relatively low data transfer rates, such as keyboard inputs.

Interrupt processing allows the processor to execute other software while the keyboard operator is thinking about what to type next. When a key is pressed, the keyboard encoder debounces the switch and puts out one pulse that interrupts the microprocessor.

Page 9: INTERRUPTS OF 8086 MICROPROCESSOR

– a time line shows typing on a keyboard,a printer removing data from memory, and a program executing

– the keyboard interrupt service procedure, called by the keyboard interrupt, and the printer interrupt service procedure each take little time to execute

Page 10: INTERRUPTS OF 8086 MICROPROCESSOR
Page 11: INTERRUPTS OF 8086 MICROPROCESSOR
Page 12: INTERRUPTS OF 8086 MICROPROCESSOR

TYPES OF INTERRUPT SOFTWARE INTERRUPTS: There are instructions in

8086 which cause an interrupt. • INT instructions with type number specified. • INT 3, Break Point Interrupt instruction. • INTO, Interrupt on overflow instruction.

HARDWARE INTERRUPTS:The primary sources of interrupts, however, are the PCs timer chip, keyboard, serial ports, parallel ports, disk drives, CMOS real-time clock, mouse, sound cards, and other peripheral devices.

Page 13: INTERRUPTS OF 8086 MICROPROCESSOR
Page 14: INTERRUPTS OF 8086 MICROPROCESSOR

The interrupt vector table contains 256 four byte entries,containg the CS:IP

Interrupt vectors for each of the 256 possible interrupts. The table is used to

locate the interrupt service routine addresses for each of those interrupts.The Interrupt vector table is located in

the first 1024 bytes of memory at addresses 000000H-0003FFH.It contains the address(segment and offset)of the

interrupt service provider

Page 15: INTERRUPTS OF 8086 MICROPROCESSOR
Page 16: INTERRUPTS OF 8086 MICROPROCESSOR

The interrupt vector table for the microprocessor and (b) the contents of an interrupt vector.

– the first five interrupt vectors are identicalin all Intel processors

– Intel reserves the first 32 interrupt vectors

– the last 224 vectors are user-available

– each is four bytes long in real mode and contains the starting address of the interrupt service procedure.

– the first two bytes contain the offset address

– the last two contain the segment address

Page 17: INTERRUPTS OF 8086 MICROPROCESSOR
Page 18: INTERRUPTS OF 8086 MICROPROCESSOR

TYPE 0The divide error : whenever the results from a division overflows or an attempt is made to divide by zero.

Page 19: INTERRUPTS OF 8086 MICROPROCESSOR
Page 20: INTERRUPTS OF 8086 MICROPROCESSOR
Page 21: INTERRUPTS OF 8086 MICROPROCESSOR

Type 2

The non-maskable interrupt occurs when a logic 1 is placed on the NMI input pin to the microprocessor. non-maskable—it cannot be disabled

Page 22: INTERRUPTS OF 8086 MICROPROCESSOR
Page 23: INTERRUPTS OF 8086 MICROPROCESSOR

Type 3A special one-byte instruction (INT 3) that uses this vector to access its interrupt-service procedure. often used to store a breakpoint in a program for debugging

Page 24: INTERRUPTS OF 8086 MICROPROCESSOR
Page 25: INTERRUPTS OF 8086 MICROPROCESSOR

TYPE 4Overflow is a special vector used with the INTO instruction. The INTO instruction interrupts the program if an overflow condition exists.

Page 26: INTERRUPTS OF 8086 MICROPROCESSOR

TYPE 5The BOUND instruction compares a register with boundaries stored in the memory. If the contents of the register are greater than or equal to the first word in memory and less than or equal to the second word, no interrupt occurs because the contents of the register are within bounds. if the contents of the register are out of bounds, a type 5 interrupt ensues as reflected by the overflow flag (OF)

Page 27: INTERRUPTS OF 8086 MICROPROCESSOR
Page 28: INTERRUPTS OF 8086 MICROPROCESSOR
Page 29: INTERRUPTS OF 8086 MICROPROCESSOR

Type 7The coprocessor not available interrupt occurs when a coprocessor is not found, as dictated by the machine status word (MSW or CR0) coprocessor control bits. if an ESC or WAIT instruction executes and no coprocessor is found, a type 7 exception or interrupt occurs

Page 30: INTERRUPTS OF 8086 MICROPROCESSOR

Type 8A double fault interrupt is activated when two separate interrupts occur during the same instruction.

Page 31: INTERRUPTS OF 8086 MICROPROCESSOR

In computing, a double fault is a serious type of error that occurs when a central processing unit (CPU) cannot adequately handle a certain type of system event that requires the CPU’s immediate attention. Double faults may cause computer crashes and error messages, automatic restarting of the machine, and the loss of any unsaved data. They are often caused by problems in the computer’s hardware such as a bad memory module or overheating CPU.

Page 32: INTERRUPTS OF 8086 MICROPROCESSOR

Type 9

The coprocessor segment overrun occurs if the ESC instruction (coprocessor opcode) memory operand extends beyond offset address FFFFH in real mode.

Page 33: INTERRUPTS OF 8086 MICROPROCESSOR

Type 10An invalid task state segment interrupt occurs in the protected mode if the TSS is invalid because the segment limit field is not 002BH or higher. usually because the TSS is not initialized

Type 11The segment not present interrupt occurs when the protected mode P bit (P = 0) in a descriptor indicates that the segment is not present or not valid.

Page 34: INTERRUPTS OF 8086 MICROPROCESSOR

• Type 12

A stack segment overrun occurs if the stack segment is not present (P = 0) in the protected mode or if the limit of the stack segment is exceeded.

Page 35: INTERRUPTS OF 8086 MICROPROCESSOR

Type 13

The general protection fault occurs formost protection violations in 80286–Core2 in protected mode system. These errors occur in Windows as general protection faults. A list of these protection violations follows.

Page 36: INTERRUPTS OF 8086 MICROPROCESSOR

• Type 13 PROTECTION VIOLATIONS

o (a) Descriptor table limit exceededo (b) Privilege rules violatedo (c) Invalid descriptor segment type loadedo (d) Write to code segment that is protectedo (e) Read from execute-only code segmento (f) Write to read-only data segmento (g) Segment limit exceededo (h) CPL = IOPL when executing CTS, HLT, LGDT,

LIDT, LLDT, LMSW, or LTR o (i) CPL > IOPL when executing CLI, IN, INS,

LOCK, OUT, OUTS, and STI

(cont.)

Page 37: INTERRUPTS OF 8086 MICROPROCESSOR

Type 14

Page fault interrupts occur for any pagefault memory or code access in 80386, 80486, and Pentium–Core2 processors.

Type 16

Coprocessor error takes effect when a coprocessor error (ERROR = 0) occursfor ESCape or WAIT instructions for 80386, 80486, and Pentium–Core2 only.

Page 38: INTERRUPTS OF 8086 MICROPROCESSOR

Type 17Alignment checks indicate word and double word data are addressed at an odd memory location (or incorrect location, in the case of a double word). interrupt is active in 80486 and Pentium–Core2

Page 39: INTERRUPTS OF 8086 MICROPROCESSOR

Type 18

A machine check activates a system memory management mode interrupt in Pentium–Core2.