Halfen Mt Fbc Us
-
Upload
corui-mihai-valer -
Category
Documents
-
view
217 -
download
0
Transcript of Halfen Mt Fbc Us
-
8/21/2019 Halfen Mt Fbc Us
1/68
HALFEN MOUNTING CHANNELS AND ACCESSORIES
FRAMING SYSTEMS
MT-FBC 10-US
-
8/21/2019 Halfen Mt Fbc Us
2/682 2012 HALFEN MT-FBC 10-US www.halfenusa.com2
y z
e2e1
yx z
FR
FL FQ
FSZ
HALFEN FRAMING AND MOUNTING SYSTEMS
Contents
HALFEN Mounting Channels, HALFEN T-bolts
- Introduction- Product range - overview: Framing and Mounting channels
- Load symbols and definitions
- Heavy duty components
- Medium duty components
- Light duty components
38
10
12
27
36
HALFEN Mounting System Accessories
- Threaded rods, hexagonal headed bolts, nuts, washers
- Channel end caps, channel cover strips
- Cantilevers
Materials, design properties, constructions
- Materials and finishes
- Channel profiles: detailed properties at a glance
- T-bolts: product range at a glance
- Welding seam sizing and bearing capacity values
- HALFEN Mounting channels as compression elements
- Calculation of bolt lengths
- T-Bolt pretension forces
44
46
47
48
50
54
56
58
59
61
Appendix:
HALFEN Framing Channels in mechanical engineering and machine building
- Specification texts
- Index
- Addresses/contact
- Static and dynamic tension tests
66
67
68
60
Fotolia
NEW!
-
8/21/2019 Halfen Mt Fbc Us
3/68 3 2012 HALFEN MT-FBC 10-US www.halfenusa.com 3
Adjustable HALFEN channel mounting systems offer a whole range of benefits:
The adjustable HALFEN channel-boltsystem is an assembly and mounting
system
Full flexibility in positioning and
dimensioning of the bolt connections
Choice of corrosion protection:
- Pre-galvanized channels
for low demands
- Hot-dip galvanized channels for
high demands
- Channels in stainless steel for high-
performance requirements
Quick assembly and adjustment of
equipment and structural components
With HALFEN mounting channels you avoid:
Time consuming planning of
inflexible bolted fixings
Costly manufacturing of bolt fixings
Costly corrosion protection work
HALFEN FRAMING AND MOUNTING SYSTEMS
Introduct ion
Quality is an outstanding feature of
our products. HALFEN materials and
products are subject to stringent quality
controls.
Quality
HALFEN cast-in channels
Certificate-no. QS-281 HH
A quality audit by Germanischer
Lloyd Certification GmbH confirmed
that our quality management
system meet the demands of the
ISO 9001:2008 standard.
All hot rolled HALFEN profiles and some
of the light framing channels are also
available as HTA/HZA HALFEN cast-in
channels for embedment into concrete.
Both versions use the same T-bolts and
locking plates.
You can find more information on
HALFEN channels in our catalogue;
"HALFEN Cast-in channels
Product Information, BP"
when upgrading already completed
structural components i.e. when
adjusting components in service
Change or up-date entire projects
with standard tools
No specialist required to carry out
modifications on-site
Dust free and low noise levels when
modification work is done on-site
Corrosion protection is not
compromised by bolting
A large selection of standard chan-
nels with good load bearing charac-
teristics. All the loads stated in this
catalogue are permissible loads
-
8/21/2019 Halfen Mt Fbc Us
4/684 2012 HALFEN MT-FBC 10-US www.halfenusa.com4
Mount ing channels HM, HL, HZM and HZL
HALFEN FRAMING AND MOUNTING SYSTEMS
Mounting channels
The hot rolling process makes these channels ideally suited to:
heavy loads
dynamic loads
connections requiring very high torque
welding
Cold-rolled channels
Channels are available with holes (ladderbacked) or without holes (plain).
Hot rolled channels
Smooth channels HM
Very high tensile loads of
up to 7.0 Kips (31 kN) are possible
High longitudinal loads of up to
1.7 Kips (7.5 kN) are possible using
nibbed T-bolts (carbon steel channels)
Cold-rolled channels HL, HM
For lower loads in longitudinal
channel direction
Economic due to large selection ofchannels
Toothed channels HZM
Toothed profile mechanically interlocks
with toothed bolt to allow high longi-
tudinal loads of up to 4.9 Kips (22 kN)
3 channel sizes for maximum
efficiency
Toothed channels HZL, HZM
For high loads in longitudinal channel
direction
Non-slip connection for high channel
loads Cantilever fixing on a vertical conveyor system
Welding jig, used in locomotive construction
Roller bearing fixing of a cableway
-
8/21/2019 Halfen Mt Fbc Us
5/68 5 2012 HALFEN MT-FBC 10-US www.halfenusa.com 5
H4.6HALFEN8.8
H4.6HALFEN4.6H4.6HALFENA4-50
H4.6HALFENA4-70
H 4.64.6
H 4.68.8
HSR All TypesHZS 29/20HZS 38/23HZS 53/34
HS All Types
HZS 41/22
HZS 41/41
H 4.6H4.6HALFEN4.6
Manufacturer
strengthgrade or material grade
(for individual dimensions)
HALFEN T-bol ts HS, HSR and HZS
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts
Type HS Type HSR Type HZS
HALFEN T-bolts; plain
Suitable for all channels
Load bearing capacity
in two directions
Marked at shank end
with one notch
HALFEN T-bolts with nibs
Only suitable for use in hot-rolled
channels from the heavy duty
system
Nibbed; therefore non-slip,
load bearing in all directions
The hook-head bolt prevents
turning under vibration
Marked at shank end with two
notches (applies only to steel)
Toothed HALFEN T-bolts
For toothed channels
HZM and HZL
Toothing also provides positive
load bearing transmission in
longitudinal channel direction.
The risk of slipping is eliminated
Marked at shank end with two
notches
Ident i fy ing HALFEN T-bol ts
Marking at the shank end of the HALFEN T-bolts: After assembly check the correct orientation of the marking on the shank end
of the T-bolts. The notch or notches must be at right angles to the channel length.
Location of
nib on bolt
Teeth in
channel
Strength class 4.6
electroplated or
hot-dip galvanized
Strength class 8.8
electroplated or
hot-dip galvanized
material grade A4 - 50
stainless steel
(Type 316, grade 50)
material grade A4 - 70
stainless steel
(Type 316, grade 70)
Notches on the shank tip:
Bolt identification on the bolt head
-
8/21/2019 Halfen Mt Fbc Us
6/686 2012 HALFEN MT-FBC 10-US www.halfenusa.com6
Locking plate GWP
Order examples
Locking plates with grip (see Me-
dium duty Framing system page 35).
The toothing grips the channel lips.
Locking plates with spring are used in
particular for securing plates or panels.
(see Medium duty Framing system
page 35).
Locking plates (channel nuts) allow
any metric bolt or threaded rod to be
used. Locking plates for UNC threads
are available.
or use the 12-digit item number e.g. 0280.200-00003 or use the 12-digit item number e.g. 0350.090-00068
HALFEN FRAMING AND MOUNTING SYSTEMS
Locking p lates
Item description for channels Item description for T-bolts
Type
Material
Thread
Length (mm)
HS 50/30 M20x100 GV-S
TypeMaterial
Length (mm)
HM 50/30 FV 6070
If you have any further questions:
Our technical department and our field support technicians
will gladly advise and support you in resolving questions
concerning HALFEN assembly systems.
HALFEN Engineering Support
Tel.: 1 800 323 6896
E-Mail: [email protected]
www.halfenusa.com
-
8/21/2019 Halfen Mt Fbc Us
7/68 7 2012 HALFEN MT-FBC 10-US www.halfenusa.com 7
Whether for low or veryhigh loads: you willalways find a cost effective
solution for your requirements
in the HALFEN range of
channels and T-bolts
Versatile and adaptable
Adjustable assembly
All connections can be adjusted at
any time; they are easily replaced
or extended
Almost unlimited in its range of
application;
e.g. Building construction,
industrial construction,
steel construction,engineering construction,
vehicle manufacturing
and many other sectors
Heavy duty mounting system
The heavy duty channels
are predominantly hot-rolled and
particularly suitable for heavy loads
Medium duty framing system
All medium duty framing and
mounting channels have the same
profile width and are compatiblewith the innovative HALFEN
Powerclick assembly system
Light duty mounting system
The light duty channel is the perfect
mounting solution for low loads
Mounting ChannelsThe advantages at a glance
Secure and reliable
Corrosion protection remainsintact after bolting
Large selection of standard chan-
nels with very good load bearing
capacities
Toothed channels for non-slip
connections
-
8/21/2019 Halfen Mt Fbc Us
8/688 2012 HALFEN MT-FBC 10-US www.halfenusa.com8
Heavy duty system
Hot-rolled Cold-rolled
HM 72/48 HM 52/34 HM 50/30 HM 49/30 HM 50/40, HL 50/40 HM 486
30
HS 72/48, HSR 72/48,GWP 72/48
HS 50/30, HSR 50/30,GWP 50/30
Medium duty system
Cold-rolled Cold-rolled, toothed Cold-rolled Cold-rolled, toothed
HM 41/41, HL 41/41 HZM 41/41, HZL 41/41 HM 41/62, HL 41/62 HM 41/83, HL 41/83 HM 41/22, HL 41/22 HZM 41/22, HZL 41/22
HZS/HS 41/41, HZS 41/22GWP 41/41, GWP 41/22
Light duty system
Cold-rolled
HM 36/36, HL 36/36 HM 38/17 HM 28/28, HL 28/28 HM 26/26, HL 26/26 HM 28/15, HL 28/15 HM 315
HS 38/17,GWP 38/17
HS 28/15,GWP 28/15
GWP 28/15
HALFEN FRAMING AND MOUNTING SYSTEMS
Product range overview: Channels + HALFEN T -bolts
Page 12 Page 14 Page 15 Page 15 Page 16 Page 16
Page 32 Page 31
Page 40
Page 29 Page 30
Page 40 Page 39 Page 38
Page 28
Page 36
Page 27
Page 36
2 7/8"
1 5/8" 1 5/8"
1 5/8"1 5/8"
1 5/8" 1 5/8"
2 1/16" 2" 2"
1 7/8"
1 5/8" 1 5/8" 2 7/16" 3 1/4" 13/16" 13/16"
1 5/16" 1 3/16" 1 3/16"1 9/16" 1 1/16"
1 15/16"1 7/8"
1 5/16"
7/8" 7/8"
7/8" 7/8"
7/8" 7/8"
7/8" 7/8" 7/8"7/8" 7/8"
1 7/16"
1 1/2"1 1/16" 1"
11
/8
" 13
/16
"1 7/16" 11/16" 1 1/8" 1" 5/8" 5/8"
11/16"
11/16" 1/2" 1/2"1/2" 5/8"
-
8/21/2019 Halfen Mt Fbc Us
9/68 9 2012 HALFEN MT-FBC 10-US www.halfenusa.com 9
Hot-rolled Cold-rolled Hot-rolled, toothed Cold-rolled, toothed
HM 40/22 HM 40/25 HM 422 HZM 53/34 HZM 38/23 HZM 29/20 HZL 63/63
25
40
18 2234
53
HS 40/22, HSR 40/22,GWP 40/22
HZS 53/34HZS/HS 38/23,HS 38/17,GWP 38/17
HZS/HS 29/20,HS 28/15,GWP 28/15
HZS 41/22,HZA/HS 41/41,HZS 41/22,GWP 41/41
Cold-rolled
HLL 41/41 HLL 41/22
Cold-rolled
HM 20/12, HL 20/12
HS 20/12,GWP 20/12
HALFEN FRAMING AND MOUNTING SYSTEMS
Product range overview: Channels + HALFEN T -bolts
Page 18 Page 18 Page 18 Page 22 Page 20 Page 24 Page 26
Page 33 Page 33
Page 42
hot-dip galvanized FV or mill finish WB
pre-galvanized SV
stainless steel A4 (comparable to 316)
stainless steel A2 (comparable to 304)
stainless steel HCR
HZM/HZL toothed profiles
Material; finishes:
For further information on materials
and finishes see page 48
NEW!
1 9/16"
7/8"11/16"
1 9/16" 1 9/16" 2 1/16"1 1/2" 1 1/8"
2 1/2"
1" 7/8 " 1 5/16"7/8 " 3/4 " 2 1/2"11/16"
11/16"7/8" 11/16"
9/16"
7/8"
1 5/8"
1 5/8"
1 5/8" 13/16"
7/8"
7/8"
3
/4"1/2"3/8"
-
8/21/2019 Halfen Mt Fbc Us
10/6810 2012 HALFEN MT-FBC 10-US www.halfenusa.com10
Symbols used for the building industry and their definition
HALFENT-headBolts
FS
Permissible load per T-boltLoad in tension and transverse load directions.T-bolts HS and smooth channels HM.
FS
Permissible load per T-boltLoad in tension, transverse and longitudinal directions.T-bolts HS and HSRwith smooth channels HM. T-bolts HZS with toothed channels HZM and HZL.
FSx Permissible load per T-bolt in longitudinal channel directionFriction coefficient thread/bearing surface =0.14; tightening factor 1.6; safety factor 3
Framingchannels
Fz
Maximum point-load capacity - centric loadThe load carrying capacity of the channel lips is decisive.Load figures are only valid for continuously welded channels, or intermittent welds according to the table on page 56.In all other cases suitability of the welding seam must be checked.
Fflex
Bending load capacity with L spanPermissible channel (as a single span element) bending load capacity depends on span distance.Limitation of the load capacity determined by bending tension and/or defined deflection.
qflex Bending load capacity with L spanPermissible line load of the channel (as a single span element) depends on span distance.Limitation of the loading capacity determined by bending tension and/or defined deflection.
Fx
Permissible load in longitudinal channel direction
Fy
Carrying capacity of the channels under transverse load angle < 60Permissible load at a defined angle to the channel, welded or bolted to support.
Fz
Carrying capacity of the channels under transverse load angle 60
Permissible load at a defined load angle to the channel, welded or bolted to support.
FK
Permissible buckling load compression rodPermissible buckling load.
M Permissible bending moment of the channel lipOnly applies to channels welded to support otherwise torsion must be taken into account.
M
FK
L
Fz
L
Fflex
L
qflex
L
Fz
Fy
Fy
Fx
Fs
Fsx
Fs
HALFEN FRAMING AND MOUNTING SYSTEMS
Load symbols and def in i t ions
F = (Fy + F
z)
F = (Fy + Fz)
The HALFEN adjustable assembly systems can be used in a wide range of fields. It is therefore important that the codes, guidelines and
design criteria applicable to each field are considered. The technical values and data for framing channels and T-bolts for use in the building,
mechanical engineering and steel construction industries are explained in the respective sections below.
-
8/21/2019 Halfen Mt Fbc Us
11/68 11 2012 HALFEN MT-FBC 10-US www.halfenusa.com 11
Symbols used for mechanical engineering steel construction industry and their definitions
HALFENT-bolts
Fv
Bolt pretension force
The bolt is pretensioned by torquing, and is calculated according to VDI 2230 guidelines
FR
Resulting forceThe resulting force F
Ris the vector addition of the external loads F
Lin the longitudinal channel direction and the external load FQ
transverse to the longitudinal channel direction; the resulting force is transferred frictionally to the channel.
FSZ
Force in the longitudinal bolt directionThe force F
SZworks as an external load along the screw longitudinal axis and perpendicular to the channel surface and is transfer-
red frictionally to the channel.
Framingchannels
Fz Maximum Point load-carrying capacity centric loadThe load carrying capacity of the channel lips is decisive.Load figures are only valid for continuous welded channels or intermittent welds according to the table on page 56.In all other cases suitability of the welding seam must be checked.
Fy
Load capacity of the channels under transverse load angle< 60Permissible load for a defined angle to the welded or bolted channels.
Fz
Load capacity of the channels under transverse load angle 60Permissible load for a defined load angle to the welded or bolted channels.
Fz
Fy
Fy
Fz
L
Fv
FL
FQ
FR
FSZ
HALFEN FRAMING AND MOUNTING SYSTEMS
Load symbols and def in i t ions
FR= (F
L + F
Q)
For further technical information and load tables applicable for mechanical engineering see pages 6065.
When designing an adjustable assembly system the external load Fimust be less than or equal to the minimum permissible load of the
T-bolt Fs and to the maximum point load capacity and respectively to the bending load capacity of the HALFEN framing channel Fz.
Fi MIN (Fs; Fz) ( see page 50)
All load figures are permissible loads.
Design load i.e. stress calculation: FR,d
= 1.4 F (forces)
Design load i.e. stress calculation: MR,d
= 1.4 M (moments)
The force Fszalong the screw longitudinal axis must be less than or equal to the maximum point load capacity of the framing channel
The force FQtransverse to the longitudinal channel direction must be less than or equal to the load capacity transverse to the
longitudinal channel direction of the framing channel Fy.
FQ F
y
Fsz F
Z
NEW!
-
8/21/2019 Halfen Mt Fbc Us
12/6812 2012 HALFEN MT-FBC 10-US www.halfenusa.com12
Dimensions and load capacities HM 72/48
Material Order-no.0280.
Length Channel-weight
Channel-cross-section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
WB 180-00002
239 5.94 1.747 0.840 2.001 0.889 1.411 6.97 12" 5.01 2.52 1.66FV 180-00003A4 180-00001
Fz= maximum bending load capacity on the channel lips
HM72
/48
y z
y
x z
y z
y
x z
72
33
54.5
48.5
15.5
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Double channel
on request
Scale 1:1
Channels HM 72/48
Accessories
VUS 72/49 washer
see page 45
HM 72/48 hot-rolled
For further channel data and static
properties see page 50
2.835"
1.299"
0.197" 0.1
77"
1.9
09"
0.6
10"
-
8/21/2019 Halfen Mt Fbc Us
13/68 13 2012 HALFEN MT-FBC 10-US www.halfenusa.com 13
Load capacity
Permissible load Thread Load capacity [kips]
M 12 2.09
M 16 3.89
M 20 4.95
Dimensions HS 72/48 and HSR 72/48
Length l[in]
HS 72/48 HSR 72/48
M 20 M 24 M 27 M 30 M20
2" FV FV
A4-50
2" FV 8.8
3" FV FV FV FV FV 8.8
GV 8.8 FV 8.8
4" FV FV FV FV
GV 8.8 GV 8.8 FV 8.8
A4-50
6" FV FV FV
GV 8.88" FV FV FV
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 12 M 12
2.44 1.22 0.87M 16 M 16
M 20 M 20
Permissible loads for T-bolts
for standard steel profiles for stainless steel
permissible loadper T-bolt
recomm. load per T-bolt in longitudinal channel directionpermissible load
per T-boltrecomm. load per T-bolt
in longitudinal channel direction
Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8
HS, GradeA4 - 50[kips]
HS, GradeA4 - 50[kips]
Tighteningtorque[lb.ft]
Thread size
4.6[kips]
8.8[kips]
[kips]
Tighteningtorque[lb.ft] [kips]
Tighteningtorque[lb.ft]
(= 3)[kips]
Tighteningtorque[lb.ft]
M 20 6.07 12.68 0.31 89 1.06 295 1.69 295 - - -
M 24 8.72 18.25 0.45 148 1.53 502 - - 8.72 0.45 148
M 27 11.35 23.83 0.58 221 2.00 738 - - - - -
M 30 13.87 29.00 0.72 295 2.45 1033 - - - - -
Note: do not exceed max. channel load bearing capacity; see page 12
Fsx FsxFs Fs
ab
d
HALFEN FRAMING AND MOUNTING SYSTEMS
T-bolts and accessor ies
HS 72/48
T-bolt
incl. nut
HSR 72/48
T-bolt with nib
incl. nut
HALFEN T-bolts HS 72/48 and HSR 72/48
Locking plates
Locking plate GWP 72/48
2.283"2.283"
-
8/21/2019 Halfen Mt Fbc Us
14/6814 2012 HALFEN MT-FBC 10-US www.halfenusa.com14
Dimensions and load bearing capacities HM 52/34
Material Order-no.0280.
length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
WB 190-00002
239 3.35 0.983 0.224 0.569 0.326 0.551 3.82 8 " 1.98 0.99 0.63FV 190-00003
A4 190-00001
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
52.5
22.5
4.1
4
33.5
10.5
Fflex
L
Fz
L
see page 46 see page 46
HPE 52/34 Channel end cap PA - 22 Channel cover
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Double channel
on request
Channels HM 52/34
For further channel data and static
properties see page 50
Accessories
VUS 52/34 Washer
see page 45
HM 52/34 hot-rolled
Scale 1:1
T-bolts see page 17
2.067"
0.161"
0.886"
1.3
19"
0.1
57"
0.4
13"
-
8/21/2019 Halfen Mt Fbc Us
15/68 15 2012 HALFEN MT-FBC 10-US www.halfenusa.com 15
Dimensions and load bearing capacities HM 50/30 and HM 49/30
Material Order-no.0280.
Length Channel-weight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 37.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 50/30
239 2.17 0.639 0.124 0.336 0.198 0.346 2.47 7" 1.19 0.61 0.36WB 200-00002
FV 200-00003
A4 200-00001HM 49/30
239 1.94 0.569 0.100 0.317 0.144 0.323 1.10 18" 0.97 0.49 0.27
WB 220-00001
FV 220-00002
A2 220-00003
A4 220-00004
Fz= maximum bending load capacity on the channel lips HCRversion on request
y z
yx z
y z
yx z
2.75
22.5
7.8
5
49
33
7.4
Fflex
L
Fz
L
see page 46
PA - 41 Channel cover
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Channels HM 50/30 and HM 49/30
For further channel data and static
properties see page 50
Accessories
VUS 52/34 Washer
see page 45
HM 50/30 hot-rolled HM 49/30 cold-rolled
SIC 50/30 Locking plate
Scale 1:1
see page 45
T-bolts see page 17
Double channel
on request
1.969"1.929"
0.866"
0.118"
0.2
91"
1.1
81"
0.886"
0.118"
0.108"
1.1
81"
0.3
09"
-
8/21/2019 Halfen Mt Fbc Us
16/6816 2012 HALFEN MT-FBC 10-US www.halfenusa.com16
Dimensions and load bearing capacities HM 50/40, HL 50/40 and HM 486
Material Order-no.
Length Profileweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 50/40 0280.
236 2.25 0.662 0.208 0.372 0.242 0.386 1.21 24" 1.53 0.76 0.52WB 090-00002
FV 090-00003
A4 090-00001
HL 50/40 0281.
236 2.12 0.578 0.171 0.369 0.223 0.383 1.21 20" 1.28 0.65 0.43WB 100-00001
FV 100-00002
A4 100-00003
HM 486 0280.
236 1.55 0.457 0.071 0.231 0.117 0.245 0.787 18" 0.74 0.38 0.20WB 100-00001
FV 100-00002
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
18
40
60
HL50
/40
HM50
/40
48
27
22
6
2.5
HM48
6
49
39
3
22
7
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Channels HM 50/40, HL 50/40 and HM 486
Accessories
For further channel data and static
properties see pages 50, 52
HM and HL 50/40 cold-rolled HM 486 cold-rolled
HPE 50/40 Channel end cap PA - 41 Channel cover
Scale 1:1
T-bolts see page 17 see page 46 see page 46
0.866"
0.118"
1.929"
1.890"
2.362"
1.575"
0.709"
0.866"
0.098"
0.27
4"
1.5
35"
1.063"
0.236"
-
8/21/2019 Halfen Mt Fbc Us
17/68 17 2012 HALFEN MT-FBC 10-US www.halfenusa.com 17
Load capacity [kips]
Permissible load Thread GWP 50/30 GWP 50/40
M 6 0.49
M 8 0.90 0.90
M 10 1.44 1.44
M 12 2.09 1.44
M 16 2.09 1.44
Permissible loads for HALFEN T-bolts
for standard steel profiles for stainless steel profiles
permissible loadper T-bolt
recomm. load per T-bolt in longitudinal channel directionpermissible load
per T-boltrecomm. load per T-bolt
in longitudinal channel direction
Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8
HS, GradeA4 - 50[kips]
HS, GradeA4 - 50[kips]
Tighteningtorque[lb.ft]
Thread size
4.6[kips]
8.8[kips]
[kips]
Tighteningtorque[lb.ft] [kips]
Tighteningtorque[lb.ft]
(= 3)[kips]
Tighteningtorque[lb.ft]
M 10 1.44 2.99 0.07 11 0.25 35 - - 1.44 0.07 11
M 12 2.09 4.36 0.11 18 0.43 52 - - 2.09 0.11 18
M 16 3.89 8.11 0.20 44 0.67 148 1.12 148 3.89 0.20 44
M 20 6.07 12.68 0.31 89 1.06 295 1.69 295 6.07 0.31 89
Note: do not exceed max. channel load bearing capacity; see page 16
Dimensions HS 50/30
Length l[in ]
Length l[in]M 10 M 12 M 16 M 20 M 10 M 12 M 16 M 20
1 1/4 " GV GV GV 2 1/2 " GV FV A4-50 A4-50 3 " GV
1 3/8 " GV A4-501 1/2 " GV GV GV/GV8.8 3 1/4 " GV/GV8.8 GV/GV8.8 GV8.8
FV FV A4-50 A4-50 A4-50
3 1/4 "Li A4-501 3/4 " GV8.8 GV/GV8.8
A4-50 4 " GV GV/GV8.8 GV/GV8.82 " GV GV GV A4-50 FV FV
A4-50 FV A4-50A4-50 5 " GV GV GV
A4-502 3/16" GV 6 " GV GV GV/GV8.8
FV FV A4-50A4-50 A4-50
2 3/8 " GV/GV8.8 GV/GV8.8 GV8.8 8 " GV GV GVA4-50 12 " GV GV
High corrosion resistance stainless steel T-bolts HS 50/30. Material order grade HCR, available on request.
Dimensions HSR 50/30
Length l[in]
Length l[in]M 10 M 12 M 16 M 20 M 10 M 12 M 16 M 20
1 1/2 " FV8.8 2 3/8 " GV8.8 GV8.8
1 3/4 " GV8.8 3 " GV8.8
Fsx FsxFs Fs
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts and accessor ies
HS 50/30
HALFEN T-bolt
incl. nut
HSR 50/30
HALFEN T-bolt
with nib
incl. nut
HALFEN T-bolts HS 50/30 and HSR 50/30
Locking plates
0.827"1.712"
0.472"
0.787"1.654"
0.315"
Locking plate
GWP 50/40
Locking plate
GWP 50/30
Li = left hand thread
1.614"
1.614"
-
8/21/2019 Halfen Mt Fbc Us
18/6818 2012 HALFEN MT-FBC 10-US www.halfenusa.com18
Dimensions and load bearing capacities HM 422 (C40)
Mat. Order-no.0280.
Length Channelweight
Channelcross-
section
Moment ofinertia
Moment ofresistance
Max. point-loadbearing capacity
Bending load capacity forspan L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
WB 110-00001236 1.04 0.307 0.031 0.103 0.063 0.132 0.56 14.17 0.41 0.20 0.09
FV 110-00002F
z= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
Dimensions and load bearing capacities HM 40/22 and HM 40/25
Material Order-no.0280.
Length Profile-weight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 40/22
239 1.41 0.415 0.047 0.141 0.099 0.163 1.28 8" 0.58 0.29 0.13WB 210-00002
FV 210-00003
A4 210-00001
HM 40/25
239 1.41 0.412 0.049 0.146 0.085 0.186 0.85 13" 0.58 0.29 0.13
WB 230-00001
FV 230-00002
A2 230-00003
A4 230-00004
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
.
2.4 2.
4 2.75
5.6
HM40
/22
Fflex
L
Fflex
L
Fz
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Channels HM 40/22, HM 40/25 and HM 422
Accessories
HM 40/22 hot-rolled HM 40/25 cold-rolled
HM 422 (C40) cold-rolled
VUS 40/25
Washer
SIC 40/22
Locking plate
see page 45 see page 45
Scale 1:1
Scale 1:1
Double channel
on request
39.5
21.
5
1.575"
0.709"
0.220"
0.108"0.709"0.094"
0.236"
0.9
06"
0.0
94"
0.9
84"
1.555"
1.555"
0.709"
0.236"
0.079"
0.8
46"
-
8/21/2019 Halfen Mt Fbc Us
19/68 19 2012 HALFEN MT-FBC 10-US www.halfenusa.com 19
Dimensions HS 40/22
Length l M 10 M 12 M 16 Length l M 10 M 12 M 16
[in] Material Material Material [in] Material Material Material
3/4 " GV GV 3 1/4 " GV GV GV
1 1/4 " GV GV GV A4-50 A4-50
FV 3 1/4 "Li A4-50 A4-50
A4-70 A4-50 A4-50 4" GV GV GV
1 1/4 " GV GV GV FV
A4-70 A4-50 A4-50 A4-50 A4-50
1 3/4 " GV
2 " GV GV GV 5" GV GV
FV FV 6" GV GV
A4-70 A4-50 A4-50 A4-50 A4-50
2" Li A4-50 8 " GV GV2 3/8 " GV GV GV A4-50
A4-50 10 " GV
12 " GV
Load bearing capacity
Permissible load Thread Load capacity [kips]
M 6 0.49
M 8 0.90
M 10 1.44
M 12 2.09
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 6
1.378 0.6690.394M 8 M 8
M 10 M 10
M 12 M 12 0.453
Dimensions HSR 40/22
Length l[in]
M 16 Length l[in]
M 16
Material Material
1 1/2 " GV 8.8 2 3/8 " GV 8.8
Permissible loads for HALFEN T-bolts
for standard steel profiles for stainless steel profiles
permissible loadper T-bolt
recomm. load per T-bolt in longitudinal channel directionpermissible load
per T-boltrecomm. load per T-bolt-
in longitudinal channel direction
Grade Grade HS, Grade 4.6 HS, Grade 8.8 HSR, Grade 8.8
HS, GradeA4 - 50[kips]
HS, GradeA4 - 50[kips]
Tighteningtorque[lb.ft]Thread
4.6[kips]
8.8[kips]
[kips]
Tighteningtorque[lb.ft] [kips]
Tighteningtorque[lb.ft]
(= 3)[kips]
Tighteningtorque[lb.ft]
M 10 1.44 2.99 0.07 11 0.25 35 - - 1.44 0.07 11
M 12 2.09 4.36 0.11 18 0.36 52 - - 2.09 0.11 18
M 16 3.90 8.11 0.20 44 0.67 148 1.12 148 3.89 0.20 44
Note: do not exceed max. channel load bearing capacity; see page 18
Fsx FsxFs Fs
32.5
32.5
Li = left hand thread
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts and accessor ies
HALFEN T-bolts HS 40/22 and HSR 40/22
Locking plate
HS 40/22
HALFEN T-bolt
incl. nut
HSR 40/22
HALFEN T-bolt
with nib
incl. nut
locking plate GWP 40/22
1.280"
1.280"
-
8/21/2019 Halfen Mt Fbc Us
20/6820 2012 HALFEN MT-FBC 10-US www.halfenusa.com20
Dimensions and load bearing capacities HZM 53/34
Material Order-no.0284.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy Iz Wy Wz Fz 19.7 in 39.4 in 59.1 in[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] F
flex[kips]
WB 070-00002
239 3.11 0.916 0.222 0.558 0.306 0.540 4.95 9 " 2.81 1.39 0.63FV 070-00003
A4 070-00001
Fz= maximum bending load capacity on the channel lips
52.5
22.5
4
4
34
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
y z
yx z
y z
yx z
Scale 1:1
Channel HZM 53/34
Accessories
HZM 53/34 hot-rolled, toothed
For further channel data and static
properties - see page 50
see page 46
PA - 22 Channel cover VUS 52/34 Washer
see page 45
NEW!
2.067"
0.886"
0.157"
1.3
39"0
.157"
-
8/21/2019 Halfen Mt Fbc Us
21/68 21 2012 HALFEN MT-FBC 10-US www.halfenusa.com 21
Dimensions HZS 53/34
Length l M 16 M 20
[in] Material Material
2 3/8 " GV8.8
A4-70
2 1/2 " GV8.8
A4-70
4 " GV8.8 GV8.8
A4-70 A4-70
Permissible loads for T-bolts
for standard steel profiles for stainless steel profilesfor stainless orstandard steelprofiles
permissible load per HALFEN T-bolt permissible load per T-bolt
Tightening torque[lb.ft]
HZSGrade A4-70
[kips]longitudinal load F
sx
[kips]Thread
Tightening torque[lb.ft]
HZSGrade 8.8
[kips]
M 16 148 8.11 148 5.314.3
M 20 258 12.68 258 8.27
Note: do not exceed max. channel load bearing capacity; see pages 20, 56
1.64
l
FsFs
Fsx
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts and accessor ies
NEW!
HZS 53/34
HALFEN T-head
bolt, toothed
incl. nut
HALFEN T-bolts toothed HZS 53/34
1.638
"
-
8/21/2019 Halfen Mt Fbc Us
22/6822 2012 HALFEN MT-FBC 10-US www.halfenusa.com22
Dimensions and load bearing capacities HZM 38/23
Material Order-no.0284.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
WB 060-00001
239 1.63 0.479 0.051 0.148 0.097 0.198 2.70 7 " 0.94 0.31 0.13FV 060-00003
A4 060-00002
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
23
38
18
33.5
HZM
38/23
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Channel HZM 38/23
Accessories
HZM 38/23 hot-rolled, toothed
For further channel data and static
properties see page 50
VUS 40/25
Washer
SIC 38/23
Locking plate
see page 45 see page 45
1.496"
0.709"
0.118" 0.1
38"
0.9
06"
-
8/21/2019 Halfen Mt Fbc Us
23/68 23 2012 HALFEN MT-FBC 10-US www.halfenusa.com 23
1.142"1.142"
Load bearing capacity
Permissible load Thread Load capacity [kips]
M 6 0.49
M 8 0.90
M 10 1.28
M 12 1.28
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 6 M 6
1.319 0.689 0.236M 8 M 8
M 10 M 10
M 12 M 12
Dimensions HZS 38/23, HS 38/23 and HS 38/17
Length l[in]
HZS 38/23 HS 38/23 HS 38/17Length l
[in]
HZS 38/23 HS 38/23 HS 38/17
M 12 M 16 M 16 M 10 M 12 M 16 M 12 M 16 M 16 M 10 M 12 M 16
3/4 " GV GV GV 2 3/4 " FV8.8
1 " A4-70 A4-50 3 1/4 " GV8.8 GV8.8 GV GV GV GV
1 1/4 " GV8.8 GV8.8 GV GV GV GV A4-50/A4-70 A4-70 A4-50/A4-70
FV FV FV 3 1/4 "Li A4-50 A4-50
A4-70 A2-70/A4-70 A2-50/A4-50 4 " GV8.8 GV8.8 GV GV GV GV
1 1/2 " GV8.8 GV8.8 GV GV GV GV FV
FV A4-50 A4-50
A4-70 A2-70/A4-70 A2-50/A4-50 5 " GV8.8 GV8.8 GV GV GV
2 " GV8.8 GV8.8 GV GV GV GV 6 " GV8.8 GV8.8 GV GV GV GV
FV FV A4-50 A4-50
A4-70 A2-70/A4-70 A2-50/A4-50 8 " GV8.8 GV GV GV
2 "Li A4-50 A4-50 A4-50 A4-50
2 3/8 " GV8.8 GV8.8 GV GV GV GV/GV8.8 12 " GV8.8
A4-50/A4-70 GV8.8 FV8.8 High corrosion resistance stainless steel T-bolts HS 38/17Material order code HCR, available on request.A4-70 A4-70 A4-50
Permissible loads for HALFEN T-bolts
HALFEN T-bolts, toothedHZS 38/23 HALFEN T-bolts, HS 38/23, HS 38/17permissible load per T-bolt permissible load per T-bolt
Thread
Tighteningtorque[lb.ft]
HZS,Grade 8.8
[kips]
HZS,Grade A4-70
[kips]longitudinal load F
sx
[kips]
Tighteningtorque[lb.ft]
HS,Grade 4.6
[kips]
HS,Grade A4-50
[kips]
HS,Grade A4-70
[kips]
M 10 - - -
2.70
11 1.44 1.96 1.44
M 12 59 4.36 2.83 18 2.09 2.83 2.09
M 16 89 8.12 5.31 44 3.89 5.31 3.89
Note: do not exceed max. channel load bearing capacity; see pages 22. 56 Permissible moment load; see page 57
Note: HALFEN T-bolts HS are not suitable for loads in directionFSx
d
a
Fs
FsxFs
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts and accessor ies
HALFEN T-bolts HZS 38/23, HS 38/23 and HS 38/17
Locking plate
HZS 38/23
HALFEN T-bolt
toothed,
incl. nut
HS 38/23
HALFEN T-bolt, incl.
nut
HS 38/17
HALFEN T-bolt,
incl. nut
Locking plate GWP 38/17
Li = Left hand thread
-
8/21/2019 Halfen Mt Fbc Us
24/6824 2012 HALFEN MT-FBC 10-US www.halfenusa.com24
Dimensions and load capacities HZM 29/20
Material Order-no.0284.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
WB 050-00001239 1.02 0.307 0.025 0.058 0.056 0.102 1.798 5 " 0.540 0.16 0.07
FV 050-00003
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
29
20
14
2.52.5
ZM29
/20
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty mount ing channels
Channel HZM 29/20
Accessories
HZM 29/20 hot-rolled, toothed
For further channel data and static
properties see page 50
SIC 29/20
Locking plate
US DIN 9021
Washer
see page 45 see page 44
1.142"
0.551"
0.098"
0.0
98"
0.7
87
0.7
87"
-
8/21/2019 Halfen Mt Fbc Us
25/68 25 2012 HALFEN MT-FBC 10-US www.halfenusa.com 25
Load bearing capacity
Permissible Load Thread Load capacity [kips]
M 6 0.43
M 8 0.63
M 10 0.67
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 6 M 60.965 0.512 0.157
M 8 M 8
M 10 M 10 1.319 0.689 0.197
Dimensions HZS 29/20, HS 29/20 and HS 28/15
Length l[in]
HZS 29/20 HS 29/20 HS 28/15 Length l[in]
HZS 29/20 HS 29/20 HS 28/15
M 12 M 12 M 6 M 8 M 10 M 12 M 12 M 12 M 6 M 8 M 10 M 125/8 " GV GV GV 2 3/8 " GV8.8 GV GV GV GV" GV GV GV A4-70
A2-70/A4-70 3 1/4 " GV8.8 GV GV GV GV
1 " GV GV GV A4-70
A2-70 4 " GV8.8 GV GV GV
A4-70 A4-501 1/4 " GV8.8 GV GV GV GV GV 5 " GV8.8 GV GV
FV A4-50
A2-70/A4-70 A2-70/A4-70 6 " GV8.8 GV GV GV
1 1/2 " GV8.8 GV GV GV GV A4-50
FV8.8 8 " GV8.8 GV
A2-70/A4-70 A4-50
2 " GV8.8 GV GV GV GV GV 10 " GV8.8
FV 12 " GV8.8
A2-70/A4-70 High corrosion resistance stainless steel T-bolts HS 38/17,Material order reference HCR, available on request.2 "Li A4-50
Permissible load for HALFEN bolts
HALFEN T-bolt toothedHZS 29/20 HALFEN T-bolt HS 28/15, HS 29/20
permissible load per HALFEN T-bolt permissible load per HALFEN T-bolt
Tighteningtorque[lb.ft]
HZS,Grade 8.8
[kips]longitudinal load F
sx
[kips]
Tighteningtorque[lb.ft]
HS,Grade 4.6
[kips]
HS,Grade A4-50
[kips]
HS,Grade A4-70
[kips]Thread
M 6 - -
1.80
2 0.49 - -
M 8 - - 6 0.90 1.24 0.90
M 10 - - 11 1.44 1.96 1.44
M 12 59 4.36 18 2.09 - -
Note: do not exceed max. channel load bearing capacity; see pages 24. 56 Permissible moment load; see page57
Note: HALFEN T-bolts HS are not suitable for loads in direction FSx
Fs
FsxFs
b
d
aLocking plate GWP 28/15
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts and accessor ies
HALFEN T-bolts HZS 29/20, HS 28/15 and HS 29/20
Locking plate
HZS 29/20HALFEN T-bolt
toothed
incl. nut
HS 28/15HALFEN T-bolt, incl.
nut
HS 29/20HALFEN T-bolt, incl.
nut
Assembly note:
M 6 and M 8:Insert locking plate at an angle
through the channel slit.
M 10:First insert the locking plate then screw
in the threaded rod.
0.827" 0.787"
-
8/21/2019 Halfen Mt Fbc Us
26/6826 2012 HALFEN MT-FBC 10-US www.halfenusa.com26
Dimensions and load bearing capacities HZL 63/63
Material Order-no.0283.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
FV 030-00001 1184.27 1.099 0.795 1.032 0.614 0.832 1.26 52 " 3.71 1.84 1.24
FV 030-00003 236
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
63
63
22
7
9.5 9.5
2.5
3
HALFEN
Scale 1:1
Fflex
L
Fz
L
28
14
250
HZL6
3/63
toothing
HALFEN FRAMING AND MOUNTING SYSTEMS
Heavy duty f raming and mount ing channel
Framing channel HZL 63/63
Accessories
HZL 63/63 cold-rolled, toothed
HALFEN T-bolts and locking platesHZS 41/41, HZS 41/22,
GWP 41/41, GWP 41/22
see medium duty framing system
see pages 34,35 see page 46 see page 46
HPE 63/63 Channel end caps PA - 41 Channel cover
For further channel data and static properties see page 52
Base channel for HALFEN Powerclick
System 63. Information about the Power-
click assembly system can be found in our
product catalogue "HALFEN Powerclick
Technical Product Information PC63".
2.480"
9.843"
1.102"
0.551"
0.118"
0.098"
0.276"
0.374" 0.866" 0.374"
2.4
80"
34/
-
8/21/2019 Halfen Mt Fbc Us
27/68 27 2012 HALFEN MT-FBC 10-US www.halfenusa.com 27
Dimensions and load capacities HM 41/41 and HL 41/41
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 41/41 0280.
236
1.75 0.516 0.172 0.222 0.187 0.272 1.26 19" 1.21 0.61 0.40
WB 080-00001
SV 080-00002
FV 080-00003
A4 080-00004
HL 41/41 0281.
1.65 0.462 0.146 0.220 0.173 0.270 1.26 16" 1.06 0.52 0.36
WB 010-00001
SV 010-00003
FV 010-00002
A4 010-00004
HM 41/41 D 0280.
3.58 1.034 0.860 0.443 0.529 0.545 1.26 52"
39.4 in 59.1 in 78.7 in
WB 150-00001
1.64 1.10 0.83FV 150-00003
A4 150-00002
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
41
41
22
7
2.5
HM
41/41
HL41/41
14
28
50
HM
41/41
D
Scale 1:1
Fflex
L
Fz
L
see page 46 see page 46
Framing Channel HM 41/41 and HL 41/41
Accessories
HM 41/41 and HL 41/41 cold-rolled
For further channel data and static properties see pages 50, 52
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
HPE 41/41 Channel end cap PA - 41 Channel cover
Double channelon request
1.614"
0.866"
0.098"
0.551"
1.6
14"
0.2
76"
1.969"
1.102"
-
8/21/2019 Halfen Mt Fbc Us
28/6828 2012 HALFEN MT-FBC 10-US www.halfenusa.com28
HZM
41/41
Dimensions and load capacities HZM 41/41 and HZL 41/41
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HZM 41/41 0284.
236
1.77 0.504 0.166 0.219 0.178 0.269 1.26 18" 1.17 0.58 0.38WB 010-00001
FV 010-00002
A4 010-00003
HZL 41/41 0283.
1.65 0.450 0.141 0.217 0.164 0.267 1.26 16" 1.01 0.52 0.25WB 010-00001
FV 010-00002
A4 010-00003
HZM 41/41 D 0284.
3.43 1.009 0.811 0.442 0.498 0.543 1.26 49 "
39.4 in 59.1 in 78.7 in
WB 030-00001
1.55 1.03 0.79FV 030-00002
A4 030-00003
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
HZL4
1/41
0.551"
1.102"
1.969"
41
41
22
7
2.5
HZM
41/41D
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
Framing channel HZM 41/41 and HZL 41/41
Accessories
HZM 41/41 and HZL 41/41 cold-rolled, toothed
For further channel data and static properties see pages 50, 52
see page 46 see page 46
HPE 41/41 Channel end cap PA - 41 Channel cover
0.098"
0.866"0.2
76"
1.614"
1.6
14"
-
8/21/2019 Halfen Mt Fbc Us
29/68 29 2012 HALFEN MT-FBC 10-US www.halfenusa.com 29
Dimensions and load capacities HM 41/62 and HL 41/62
Material Order-no.
Length Channelweight
Channelcross-
sectiont
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for span L [in]
G A Iy
Iz
Wy
Wz
Fz
39.4 in 78.7 in 118 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex[kips]
HM 41/62 0280.
236
2.30 0.676 0.485 0.315 0.361 0.388 1.26 36" 1.15 0.58 0.34WB 140-00002
SV 140-00001
FV 140-00003
HL 41/62 0281.
2.11 0.618 0.415 0.313 0.334 0.385 1.26 32" 1.01 0.49 0.29WB 040-00001
SV 040-00003
FV 040-00002
HM 41/62 D0280.
4.60 1.352 2.597 0.630 1.065 0.774 1.26 106"
39.4 in 59.1 in 78.7 in
WB 170-000013.33 2.23 1.66
FV 170-00002 F
z= maximum bending load capacity on the channel lips
y z
y
x z
y z
y
x z
41
62
22
7
2.5
HM41
/62
HL41/62
0.551"
1.102"
1.969"
HM41
/62D
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
see page 46
Framing channel HM 41/62 and HL 41/62
Accessories
HM 41/62 and HL 41/62 cold-rolled
For further channel data and static
properties see pages 50, 52
PA - 41 Channel cover
Note for span distance L:Brace channel during installation to prevent
possible buckling or twisting when load is
applied.
1.614"
0.276"
0.098"
0.866"
2.4
41"
-
8/21/2019 Halfen Mt Fbc Us
30/6830 2012 HALFEN MT-FBC 10-US www.halfenusa.com30
Dimensions and load capacities HM 41/83 and HL 41/83
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
39.4 in 78.7 in 118 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex [kips]
HM 41/83 0280.
236
2.84 0.835 1.021 0.408 0.581 0.502 1.26 58" 1.84 0.92 0.61WB 130-00002
SV 130-00001
FV 130-00003
HL 41/83 0281.
2.64 0.778 0.891 0.407 0.540 0.500 1.26 52" 1.64 0.83 0.54WB 030-00004
SV 030-00006
FV 030-00005F
z= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
41
83
22
7
2.5
HM41
/83
0.551"
28
50
HL41
/83
1.102"
1.969"
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
Framing channels HM 41/83 and HL 41/83
Accessories
HM 41/83 andHL 41/83 cold-rolled
For further channel data and static
properties see pages 50, 52
see page 46
PA - 41 Channel cover
Note for span distance L:
Ensure that the channel mounting
structure is braced to prevent late-
ral torsional buckling when load is
applied.
1.614"
0.098"
0.866"
0.2
76"
3.268"
-
8/21/2019 Halfen Mt Fbc Us
31/68 31 2012 HALFEN MT-FBC 10-US www.halfenusa.com 31
Dimensions and load bearing capacities HM 41/22 and HL 41/22
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 41/22 0280.
236
1.20 0.357 0.029 0.128 0.059 0.157 1.26 5 " 0.40 0.18 0.09
WB 120-00001
SV 120-00002
FV 120-00003
A4 120-00004
HL 41/22 0281.
1.10 0.302 0.024 0.127 0.054 0.156 1.26 4 " 0.36 0.16 0.07
WB 020-00001
SV 020-00003
FV 020-00002
A4 020-00004
HM 41/22 D 0280.
2.42 0.711 0.133 0.256 0.164 0.314 1.26 16"
39.4 in 59.1 in 78.7 in
WB 160-00001
0.52 0.34 0.20FV 160-00002
A4 160-00003
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
41
21
22
7
2.5
HM41
/22
HL41
/22
0.551"
1.102"
1.969"
HM41
/22D
Scale 1:1
Fflex
L
Fz
L
Framing channels HM 41/22 and HL 41/22
Accessories
HM 41/22 and HL 41/22 cold-rolled
For further channel data and static
properties see pages 50, 52
HPE 41/41 Channel end cap PA - 41 Channel cover
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
see page 46 see page 46
1.614"
0.866"
0.098"
0.8
27"
0.2
76"
-
8/21/2019 Halfen Mt Fbc Us
32/6832 2012 HALFEN MT-FBC 10-US www.halfenusa.com32
Dimensions and load bearing capacities HZM 41/22 and HZL 41/22
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HZM 41/22 0284.
239 1.20 0.344 0.028 0.125 0.056 0.154 1.26 5" 0.38 0.18 0.07WB 020-00001
FV 020-00002
A4 020-00003
HZL 41/22 0283.
236 1.10 0.290 0.023 0.124 0.052 0.151 1.26 4 " 0.34 0.13 0.07WB 020-00001
FV 020-00002
A4 020-00003
HZM 41/22 D 0284.
239 2.41 0.722 0.136 0.264 0.164 0.325 1.26 16"
39.4 in 59.1 in 78.7 in
WB 040-00001
0.52 0.34 0.20FV 040-00002
A4 040-00003
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
41
21
22
7
2.5
HZM
41/22
HZM
41/22
D
0.551"
1.102"
1.969"
HZL4
1/22
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
Framing channels HZM 41/22 and HZL 41/22
Accessories
HZM 41/22 and HZL 41/22 cold-rolled, toothed
For further channel data and static
properties see pages 50, 52
HPE 41/41 Channel end cap
PA - 41 Channel cover
see page 46 see page 46
1.614"
0.098"
0.866"
0.8
27"
0.2
76"
-
8/21/2019 Halfen Mt Fbc Us
33/68 33 2012 HALFEN MT-FBC 10-US www.halfenusa.com 33
Dimensions and load capacities HLL 41/41 and HLL 41/22
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HLL 41/41 0282.
236
1.08 0.298 0.102 0.147 0.124 0.180 0.40 35 /" 0.72 0.36 0.22SV 010-00002
HLL 41/22 0282.0.77 0.206 0.018 0.088 0.043 0.109 0.40 12/" 0.25 0.09 0.04
SV 020-00003
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
41
21
22
7
1.50.551"
1.102"
1.969"
HLL4
1/22
41
41
22
7
.5
1.5
HLL4
1/41
0.551"
1.102"
1.969"
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Medium duty f raming and mount ing channels
Framing channels HLL 41/41 and HLL 41/22
Accessories
HLL 41/41 cold-rolled HLL 41/22 cold-rolled
HPE 41/41
HPE 41/22 Channel end cap PA - 41 Channel cover
see page 46 see page 46
1.614"
1.614"
0.866"
0.866"
0.059"0.059"
1.6
14"
0.8
27"
0.2
76"
0
.295"
-
8/21/2019 Halfen Mt Fbc Us
34/6834 2012 HALFEN MT-FBC 10-US www.halfenusa.com34
Dimensions HZS 41/41, HZS 41/22 and HS 41/41
Length l["]
HZS 41/41 HZS 41/22 HS 41/41
M6 M8 M10 M12 M16 M12 M16 M10 M12
11/4 " zinc flake coated zinc flake coated zinc flake coated zinc flake coated
13/8 " FV8.8 A4-50 FV4.6 FV4.6
A4-50 A4-50 A4-50
2"zinc flake coated zinc flake coated zinc flake coated
FV8.8 FV8.8 FV4.6
A4-50 A4-50
2 1/2 " zinc flake coated
3 " zinc flake coated zinc flake coated
3 1/4 " A4-50
4 " zinc flake coated FV8.8
FV
4 1/32" zinc flake coated
Permissible loads for T-bolts
HALFEN T-bolts toothedHZS 41/41 HALFEN T-bolts toothedHZS 41/22 HALFEN T-bolts HS 41/41
permissible load per T-bolt permissible load per T-bolt recomm. load per T-bolt
Tighte-ning
torque[lb.ft]
allchannels
Fs[kips]
HM/HL
Fsx[kips]
HZM/HZL
Fsx[kips]
Tighte-ning
torque[lb.ft]
HLL
Fsx[kips]
Tighteningtorque
Grade 8.8
(Grade A4)[lb.ft]
allchannelsGrade8.8
Fs[kips]
HZM/HZL
Grade8.8
Fsx[kips]
allchannelsGradeA4-50
Fs[kips]
HM/HL
GradeA4-50
Fsx[kips]
HZM/HZL
GradeA4-50
Fsx[kips]
Tightening
torque[lb.ft]
HM/HLGrade4.6
Fs[kips]
HM/HLGrade 4.6
Fsx[kips]
HM/HLGradeA4-50
Fs[kips]
HM/HLGradeA4-50
Fsx[kips]Thread
M 6 9 1.12 0.22 0.49 9 0.22 - - - - - - - - - - -
M 8 21 1.35 0.54 0.90 21 0.54 - - - - - - - - - - -
M 10 41 1.57 0.79 1.12 41 0.79 - - - - - - - - - - -
M 12 44 1.57 0.90 1.12 41 0.81 37 (37) 1.57 1.12 1.57 0.38 1.12 11 (11) 1.44 0.07 1.44 0.07
M 16 92 2.70 1.69 1.69 70 1.01 59 (59) 2.70 1.69 2.70 0.90 1.12 18 (18) 2.09 0.11 6.86 0.11
Note: do not exceed max. channel load bearing capacity; see pages 2733 and 56
Fs FsFsx Fsx Fsx
Fs
l
34.5
l
34.5
1.39"
l
HALFEN FRAMING AND MOUNTING SYSTEMS
Halfen T -bolts and accessor ies
HALFEN T-bolts HZS 41/41, HZS 41/22 and HS 41/41
HZS 41/41
HALFEN T-bolts
toothed
(order nut separately)
HZS 41/22
HALFEN T-bolts
toothed, incl. nut
HS 41/41
HALFEN T-bolts,
incl. nut
HALFEN T-bolts for all 41 profiles':
for toothed Profiles
41/41 and 41/22
Application notes: HZS 41/41:
- M16not suitable for channels 41/22
- M16can only be mounted by sliding on at channel end
- M16x 4 / without teeth, FSx
= 0.90 kips
1.358"
1.358"
1.386"
-
8/21/2019 Halfen Mt Fbc Us
35/68 35 2012 HALFEN MT-FBC 10-US www.halfenusa.com 35
Dimensions GWP 41/41 SN
GV
Thread
d
[in]
b
[in]
a
[in]
M 6 0.236
0.787 1.358
M 8 0.315
M 10
0.354
F M 12
Load Bearing capacity GWP 41/41, - SN, -SH
Thread
all ProfilesF
S
[kips]
Tighteningtorque[lb.ft]
HM/HLF
Sx
[kips]
HZM/HZLF
Sx
[kips]
Tighteningtorque[lb.ft]
HLLF
Sx
[kips]
HM/HLF
S
[kips]
Tighteningtorque[lb.ft]
HM/HLF
Sx
[kips]
HZM/HZLF
Sx
[kips]
M 6 1.12 2.70 0.22 0.49 2.70 0.22 1.12 1.46 0.07 0.49
M 8 1.35 6.29 0.54 0.90 6.29 0.54 1.35 3.60 0.13 0.90
M 10 1.57 12.36 0.79 1.12 12.36 0.79 1.57 7.08 0.27 1.12
M 12 2.02 16.86 1.12 1.12 12.36 0.81 - - - -
F M12 1.57 13.49 0.90 1.12 12.36 0.81 1.57 12.36 0.38 1.12
M16 2.70 28.10 1.69 1.69 21.36 1.01 2.70 28.10 0.90 1.12
Load bearing capacity GWP 41/22
Thread
FS
[kips]
Tighteningtorque[lb.ft]
HZM/HZLF
Sx
[kips]
HM/HLF
S
[kips]
Tighteningtorque[lb.ft]
HM/HLF
Sx
[kips]
HZM/HZLF
Sx
[kips]
M 6 1.12 2.70 0.22 - - - -
M 8 1.35 6.29 0.54 1.35 3.60 - 0.90
M 10 1.57 12.36 0.79 1.57 7.08 - 1.12
M 12 2.02 11.24 0.81 1.57 11.24 - 1.12
M 16 1.57 17.98 1.01 1.57 17.98 - 1.12
Dimensions GWP 41/41
GV
Thread
FV
Thread
A4
Thread
d
[in]
b
[in]
a
[in]
M 6 M 6 0.234
0.787
1.358
M 8 M 8 M 80.315 /0.236
M 10 M 10 M 10
0.354F M12 F M12 F M12
M12 M12 0.472
M16 M16 0.472 1.181
Dimensions GWP 41/22
GV
Thread
A4
Thread
d
[in]
b
[in]
a
[in]
M 6 -
0.295 0.787 1.358
M 8 M 8
M 10 M 10
M 12 M 12
M 16 M16
On request
Dimensions GWP 41/41 SH
GV
Thread
d
[in]
b
[in]
a
[in]
M 6 0.236
0.787 1.358
M 8 0.315
M 10 0.354
M 12 0.472
b a
d
ba
dd
ba
b
d
a
Fsx Fsx
Fsx Fsx
HALFEN FRAMING AND MOUNTING SYSTEMS
Locking p lates Medium duty f raming and mount ing system
Locking plates
GWP 41/41
Locking plates
GWP 41/41 SN
Locking plates
GWP 41/41 SH
Locking plate
GWP 41/22
Locking plates GWP 41/41 - SN, - SH, GWP 41/22
Locking plates for all 41profiles and
profile 63/63
Locking plates with short spring for
profiles 41/22and 63/63
Locking plates with long spring for
profile 41/41
Locking platefor toothed channels
41/22 and 41/41
Application notes: GWP 41/41: - M12 + M16not suitable for channels 41/22 and 63/63
- M16can only be mounted by sliding on at channel end
UNC threads are available. Please contact Halfen customer service.
-
8/21/2019 Halfen Mt Fbc Us
36/6836 2012 HALFEN MT-FBC 10-US www.halfenusa.com36
Dimensions and load capacities HM 36/36, HL 36/36, HM 38/17
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
t
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex[kips]
HM 36/36 0280.
236
1.47 0.432 0.108 0.141 0.133 0.198 0.99 17" 0.88 0.43 0.29WB 070-00001FV 070-00002
A4 070-00003
HL 36/36 0281.
1.34 0.375 0.088 0.139 0.120 0.196 0.99 14/" 0.72 0.36 0.25WB 050-00001
FV 050-00002
A4 050-00003
HM 38/17 0280.
239 1.22 0.357 0.020 0.103 0.050 0.138 1.08 4" 0.34 0.13 0.07
WB 020-00001
FV 020-00002
A2 020-00003
A4 020-00004
Fz= maximum bending load capacity on the channel lips HCRversion on request
y z
yx z
y z
yx z
36
36
18
2.5
HM36
/361.5
75"
2.362"
0.591"
HL36
/36
38
17
.53
18 HM
38/17
Scale 1:1
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Light duty f raming and mount ing channels
Framing channels HM 36/36, HL 36/36 and HM 38/17
Accessories
HM 36/36 and
HL 36/36 cold-rolledHM 38/17 cold-rolled
For further channel data and staticproperties see pages 50, 52
SIC 38/17 Locking plate
see page 45 see page 46 see page 46
HPE 36/36Channel end cap
for HM 36/36
and HL 36/36
PA - 18H Channel cover
1.417"
1.496"
0.709"
0.118"0.098"
0.709
1.4
17"
0.6
89"
-
8/21/2019 Halfen Mt Fbc Us
37/68 37 2012 HALFEN MT-FBC 10-US www.halfenusa.com 37
Load bearing capacity
Permissible load Thread Load capacity [kips]
M 6 0.49
M 8 0.90
M 10 1.28
M 12 1.28
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 6 M 6
1.319 0.689 0.236M 8 M 8
M 10 M 10
M 12 M 12
Permissible loads for T-bolts
for standard steel profile for stainless steel profiles
permissible loadper HALFEN T-bolt
recomm. load per T-boltin longitudinal channel direction
permissible loadper HALFEN T-head bol
recomm. load per T-boltin longitudinal channel direction
Grade Grade HS, Grade 4.6 HS, Grade 8.8
HS, GradeA2/A4 - 50
[kips]
HS, GradeA2/A4 - 70
[kips]
HS, GradeA2/A4 - 50/70
[kips]Tightening torque
[lb.ft]Thread
4.6[kips]
8.8[kips]
[kips]
Tighteningtorque[lb.ft] [kips]
Tighteningtorque[lb.ft]
M 10 1.44 2.99 0.07 11 0.25 35 1.44 1.96 0.07 11
M 12 2.09 4.36 0.11 18 0.36 52 2.09 2.83 0.11 18
M 16 3.89 8.12 0.20 44 0.67 148 3.89 5.31 0.20 44
Note: do not exceed max. channel load bearing capacity; see page 36
Dimensions HS 38/17
Length l["]
Length l["]M 10 M 12 M 16 M 10 M 12 M 16
3/4" GV GV GV 23/8 " GV GV GV
1 " A4-70 A4-50 FV8.8
1 1/4 " GV GV GV A4-70 A4-70 A4-50
FV FV FV 23/4 " FV8.8
A4-70 A2-70 A2-50 31/4 " GV GV GV
A4-70 A4-50 A4-70 A4-50
1 1/2 " GV GV GV 31/4 "Li A4-50 A4-50
FV 4" GV GV GV
A4-70 A2-70 A2-50 FV
A4-70 A4-50 A4-50 A4-502" GV GV GV 5" GV GV
FV FV 6" GV GV GV
A4-70 A2-70 A2-50 A4-50 A4-50
A4-70 A4-50 8" GV GV
2" Li A4-50 A4-50 A4-50 A4-50
High corrosion resistance stainless steel T-bolts HS 38/17,Material order code HCR, available on request.
Fsx FsxFs Fs
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts a nd accessor ies
Locking plates GWP 38/17
HALFEN T-bolts HS 38/17
Locking plates
HS 38/17
HALFEN T-bolts incl. nutLi = with left hand thread
1.142"
-
8/21/2019 Halfen Mt Fbc Us
38/6838 2012 HALFEN MT-FBC 10-US www.halfenusa.com38
Dimensions and load capacities HM 28/28 and HL 28/28
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 28/28 0280.
236
0.91 0.268 0.041 0.048 0.066 0.091 0.67 12 /" 0.43 0.20 0.11
WB 050-00001
SV 050-00003
FV 050-00002A4 050-00004
HL 28/28 0281.
0.82 0.229 0.032 0.048 0.058 0.090 0.67 10 /" 0.34 0.18 0.09
WB 060-00001
SV 060-00003
FV 060-00002
A4 060-00004
Fz= maximum bending load capacity on the channel lips
28
12
27
2
HM28
/28
12,5
25
40
HL28
/28
Scale 1:1
y z
yx z
y z
yx z Fflex
L
Fz
L
Framing channels HM 28/28 and HL 28/28
Accessories
HM 28/28 and HL 28/28 cold-rolled
For further channel data and static
properties see pages 50, 52
see page 46
HPE 28/28 Channel end cap
HALFEN FRAMING AND MOUNTING SYSTEMS
Light duty f raming and mount ing channels
1.063"
0.492"
0.984"
1.575"
0.079"
0.472"
1.1
02"
-
8/21/2019 Halfen Mt Fbc Us
39/68 39 2012 HALFEN MT-FBC 10-US www.halfenusa.com 39
Dimensions and load capacities HM 26/26 and HL 26/26
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 26/26 0280.
236
0.55 0.163 0.023 0.028 0.039 0.055 0.25 19 " 0.25 0.11 0.07SV 040-00001
HL 26/26 0281.0.48 0.138 0.018 0.028 0.034 0.054 0.25 15 " 0.20 0.90 0.05
SV 070-00001F
z= maximum bending load capacity on the channel lips
26
26
12
1.25
HM26
/26 25
40
HL26/26
12,5
Scale 1:1
y z
yx z
y z
yx z
Fflex
L
Fz
L
Framing channels HM 26/26 and HL 26/26
Accessories
HM 26/26 and HL 26/26 cold-rolled
For further channel data and static
properties see pages 50, 52
HPE 26/26Channel end cap
HALFEN FRAMING AND MOUNTING SYSTEMS
Light duty f raming and mount ing channels
see page 46
1.024"
0.049"
0.472"
0.492"
1.575"
0.984"1
.024"
/
1116/
-
8/21/2019 Halfen Mt Fbc Us
40/6840 2012 HALFEN MT-FBC 10-US www.halfenusa.com40
Dimensions and load bearing capacities HM 315 (C30)
Mat. Order-no.0280.
LengthChannelweight
Channelcross-
section
Moment ofinertia
Moment ofresistance
Max. point-loadbearing capacity
Bending load capacityfor span L [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
WB 060-00001236 0.52 0.150 0.007 0.030 0.020 0.051 0.37 6.969 0.13 0.04 0.02
FV 060-00002
Fz= maximum bending load capacity on the channel lips
y z
yx z
y z
yx z
Dimensions and load capacities HM 28/15, HL 28/15, HM 315 (C30)
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 34.4 in 59.7 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 28/15 0280.
239
0.73 0.215 0.010 0.035 0.028 0.063 0.877 3.228 0.18 0.07 0.03
WB 010-00001
FV 010-00002
A2 010-00004
A4 070-00003
HL 28/15 0281.
0.58 0.180 0.008 0.032 0.024 0.060 0.877 2.756 0.16 0.05 0.02
WB 080-00001
FV 080-00004A2 080-00002
A4 080-00003
Fz= maximum bending load capacity on the channel lips HCRversion on request
Fflex
L
Fz
L
15
.25
12
28
2.25
HM28
/15 25
40
HL28
/15
15
16
30
1.5
HM31
5
Scale 1:1
Scale 1:1
y z
yx z
y z
yx z
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Light duty f raming and mount ing channels
Framing channel HM 28/15, HL 28/15 and HM 315 (C30)
Accessories
HM 28/15 andHL 28/15 cold-rolled
HM 315 (C30) cold-rolled
For further channel data and static
properties see pages 50, 52
SIC 38/17 Locking plate
see page 45
1.102"
1.181
0.059
0.630
0.089"
0.472"
0.354"
1.575"
0.984"
0.6
00"
0.5
91
-
8/21/2019 Halfen Mt Fbc Us
41/68 41 2012 HALFEN MT-FBC 10-US www.halfenusa.com 41
Dimensions HS 28/15
Length l["]
Length l["]M 6 M 8 M 10 M 12 M 6 M 8 M 10 M 12
5/8" GV GV GV 2 " GV GV GV GV3/4" GV GV GV FV
A2-70 A2-70
A4-70 A4-70
1 " GV GV GV 2 3/8" GV GV GV
A2-70 A4-70
A4-70 3 1/4" GV GV GV
1 1/4" GV GV GV GV A4-70
FV 4 " GV GV
A2-70 A2-70 A4-50
A4-70 A4-70 5 " GV
1 1/2" GV GV GV A4-50FV8.8 6 " GV GV
A2-70 A4-50
A4-70 8 " GV
2 "Li A4-50 A4-50
High corrosion resistance stainless steel HALFEN T-bolts HS 28/15,Material order code HCR, available on request.
Load bearing capacity
Permissible load Thread Load capacity [kips]
M 6 0.43
M 8 0.63
M 10 0.67
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 6 M 60.965 0.512 0.157
M 8 M 8
M 10 M 10 1.319 0.689 0.197
Installation note:M 6 and M 8:Insert locking plate at a slant anywhere through the channel opening.
M 10:First insert the locking plate then screw in the threaded rod.
Permissible loads for HALFEN T-bolts
for standard steel profiles for stainless steel profiles
permissible loadper HALFEN T-bolt
recomm. load per HALFEN T-bolt-in longitudinal channel direction
permissible loadper HALFEN T-bolt
recomm. load per HALFEN T-bolt-in longitudinal channel direction
HS, GradeA2/A4 - 50
[kips]
HS, GradeA2/A4 - 70
[kips]
HS, GradeA2/A4 - 50/70
[kips]Tightening torque
[lb.ft]Thread
Grade4.6
[kips]
HS, Grade4.6
[kips]Tightening torque
[lb.ft]
M 6 0.49 0.02 2 0.49 0.67 0.02 2
M 8 0.90 0.04 6 0.90 1.24 0.04 6
M 10 1.44 0.07 11 1.44 1.96 0.07 11
M 12 2.09 0.11 18 2.09 2.83 0.11 18
Note: do not exceed max. channel load bearing capacity. see page 40
Fsx FsxFs Fs
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts a nd accessor ies
Locking plates GWP 28/15
HALFEN T-bolt HS 28/15
Locking plates
HS 28/15
HALFEN T-bolt incl. nut
(not for HM 315)
for Profiles 28/15 and 315 (C30)
Li = with left hand thread
0.787"
-
8/21/2019 Halfen Mt Fbc Us
42/6842 2012 HALFEN MT-FBC 10-US www.halfenusa.com42
Dimensions and load bearing capacities HM 20/12 and HL 20/12
Material Order-no.
Length Channelweight
Channelcross-
section
Moment of inertia Moment of resistance Max. point-loadbearing capacity
Bending load capacity for spanL [in]
G A Iy
Iz
Wy
Wz
Fz
19.7 in 39.4 in 59.1 in
[in] [lb/ft] [in] [in4] [in4] [in] [in] [kips] L [in] Fflex
[kips]
HM 20/12 0280.
236
0.35 0.102 0.003 0.009 0.010 0.022 0.504 2.283 0.07 0.02 0.01WB 030-00001
FV 030-00003
A2 030-00002
HL 20/12 0281.
0.30 0.082 0.002 0.008 0.009 0.022 0.504 1.811 0.05 0.01 0.01WB 090-00001
FV 090-00002
A2 090-00003
Fz= maximum bending load capacity on the channel lips
12
10
20
1.5
HM20
/12 HL
20/12
0.354
0.984
1.575
SIC
Scale 1:1
y z
yx z
y z
yx z
Fflex
L
Fz
L
HALFEN FRAMING AND MOUNTING SYSTEMS
Light duty f raming and mount ing systems
Framing channels HM 20/12 and HL 20/12
Accessories
HM 20/12 and
HL 20/12 cold-rolled
For further channel data and static
properties see pages 50, 52
SIC 20/12 Locking plate
see page 45
0.787"
0.394"
0.059"
0.4
72"
-
8/21/2019 Halfen Mt Fbc Us
43/68 43 2012 HALFEN MT-FBC 10-US www.halfenusa.com 43
Dimensions HS 20/12
Length l["] M 6 M 8
5/8" GV3/4" GV GV
A2-70
1 " GV
1 1/4" GV GV
A2-70
1 1/2" GV GV
A2-70
2" GV GV
A2-702 3/8" GV GV
3 1/4" GV
4" GV
Dimensions
GV
Thread
A4
Thread
a
[in]
b
[in]
d
[in]
M 5 M 5
0.630 0.354 0.157
M 6 M 6
Load bearing capacity
permissible load Thread Load capacity [kips]
M 5 0.34
M 6 0.43
Permissible loads for T-bolts1
for standard steel profiles for stainless steel profiles
permissible loadper HALFEN T-bolt
permissible loadper HALFEN T-bolt in
longitudinal channel direction
permissible loadper HALFEN T-bolt
permissible loadper HALFEN T-bolt in
longitudinal channel direction
Grade
HS, GradeA2 - 70[kips]
HS, GradeA2 - 70[kips]
Tightening torque[lb.ft]Thread
4.6[kips]
HS, Grade4.6
[kips]Tightening torque
[lb.ft]
M 6 0.49 0.02 2 0.67 0.02 2
M 8 0.90 0.04 6 1.24 0.04 6
Note: do not exceed max. channel load bearing capacity see page 42
Fsx FsxFs Fs
l
15.5
Locking plates GWP 20/12
HALFEN T-bolts HS 20/12
Locking plates
HS 20/12
HALFEN T-bolts
incl. nut
HALFEN FRAMING AND MOUNTING SYSTEMS
HALFEN T-bolts and accessor ies
0.610"
-
8/21/2019 Halfen Mt Fbc Us
44/6844 2012 HALFEN MT-FBC 10-US www.halfenusa.com44
GVFK 4.6
Thread
Stainless steelA4
Thread
Length
[in]
Loadcapacity
[kips]M 6 M 6 39.4 0.49
M 8 M 8 39.4 0.90
M 10 M 10 39.4 1.44
M 12 M 12 39.4 2.09
M 16 M 16 39.4 3.89
M 20 M 20 39.4 6.07
M 24 39.4 8.72
Order example:: GWS - M 12 1000 - GV
GVFK 8.8
Dimensions
Stainless steelA4
Dimensions
S S
DIN EN
[in] [in]
M 6x 12 0.394 0.394
M 6x 25
M 8 x 25 M 8 x 250.512 0.512
M 8 x 40
M 10 x 20
0.669 0.630
M 10 x 30 M 10 x 30
M 10 x 45 M 10 x 45
M 10 x 60
M 10 x 70
M 12 x 22
0.748
0.709
M 12 x 25 M 12 x 25
M 12 x 30 M 12 x 30
M 12 x 40 M 12 x 40
M 12 x 50
M 12 x 60 M 12 x 60M 12 x 80 M 12 x 80
M 12 x 90
M 16x 40 M 16x 40
0.945 0.945M 16x 60 M 16x 60
M 16x 90 M 16x 90
GVFK 8
Thread
Stainlesssteel A4Thread
S/m S/m e
DIN ISO DIN
[in] [in] [in]
M 6 M 6 0.394/0.197 0.394/0.236 0.453
M 8 M 8 0.512/0.256 0.512/0.295 0.591
M 10 M 10 0.669/0.315 0.630/0.374 0.772
M 12 M 120.748/0.394 0.709/0.472 0.862
M 16 M 16 0.945/0.512 0.945/0.610 1.091
M 20 M 20 1.181/0.630 1.181/0.748 1.362
M 24 M 24 1.417/0.748 1.417/0.866 1.634
FV
Thread
Stainlesssteel A2Thread
S/m S/m e
DIN EN
[in] [in] [in]
M6, M8 M 8 0.512/0.256 0.512/0.295 0.591
M 10 M 10 0.669/0.315 0.630/0.374 0.772
M 12 M 12 0.748/0.394 0.709/0.472 0.862
M 16 M 16 0.945/0.512 0.945/0.610 1.091
GV
for Screw size
Stainlesssteel A4
for Screwsize
D d s
[in] [in] [in]
M 6 M 6 0.472 0.252 0.063
M 8 M 8 0.630 0.331 0.063
M 10 M 10 0.827 0.413 0.079
M 12 M 12 0.945 0.512 0.098
M 16 M 16 1.181 0.669 0.118
M 20 M 20 1.457 0.827 0.118
M 24 M 24 1.732 0.984 0.157
FV
for Screw size
Stainlesssteel A2for Screw
size
D d s
[in] [in] [in]
M 8 0.669 0.331 0.063
M 10 M 10 0.827 0.413 0.079
M 12 M 12 0.945 0.512 0.098
M 16 M 16 1.181 0.669 0.118
Order example:: US - GV - M 12 - DIN 125
DINEN
GVfor Screw
size
Stainlesssteel A4for Screw
size
D d s
[in] [in] [in]7094 M 6 0.866 0.260 0.079
7093-1 M 8 M 8 0.945 0.331 0.079
7093-1 M 10 M 10 1.181 0.413 0.098
7094 M 12 1.772 0.531 0.157
7093-1 M 12 M 12 1.457 0.512 0.118
7093-1 M 16 M 16 1.969 0.669 0.118
7094 M 20 2.835 0.866 0.236
Order example:: US - M 12 - GV - DIN EN ISO 7093-1
FV
Type
Stainlesssteel A4
Type
t b d F
[in] [in] [in] [kips]
1 1 0.236 1.575 0.512 0.34
2 2 0.315 1.969 0.669 0.74
3 3 0.394 1.969 0.669 1.12
recommended. max. load
3.
937
0.787
1.969
Cross-section
GWS
Threaded rod
DIN 976-1
HSK
Hex. head bolt
DIN 933 or
DIN EN ISO 4017
(without nut)
MU
Hex. head nut
DIN 934 or
DIN EN ISO 4032
Hex. head T-bolts areused in combinationwith HALFEN lockingplates
US
Washers
DIN EN ISO
7093-1/7094,
DIN 440
US
Washers
DIN 125/
DIN EN
ISO 7089
HJV
Adjustment
coupler
HALFEN FRAMING AND MOUNTING SYSTEMS
Threaded rods, hexagon head bolts, nuts, washers
-
8/21/2019 Halfen Mt Fbc Us
45/68 45 2012 HALFEN MT-FBC 10-US www.halfenusa.com 45
GV
thread size
Stainlesssteel A4
thread size
D Lload
capacity
[in]
[in]
[kips]M 6 M 6 0.394/0.394 0.591 0.49
M 8 M 8 0.472/0.551 0.787 0.90
M 10 M 10 0.512/0.630 0.984 1.44
M 12 M 12 0.630/0.787 1.181 2.09
M 16 M 16 0.827/0.984 1.575 3.89
M 20 M 20 1.024/1.260 1.969 6.07
Recomm. maximum working load at centric-pull
Size D for type GV / A4
FV
thread size
Stainlesssteel A4
thread size
S Lload
capacity
[in]
[in]
[kips]
M 10 M 10 0.512 1.575 1.44
M 12 M 12 0.669 1.575 2.09
M 16 M 16 0.866 1.969 3.89
Recomm. maximum working load at centric-pullOrder example: SKM - FV - M 12
Stainless steel A4
Thread M 12 Length L [in]
Stainless steelA4
Thread M 16 Length L [in]
D D
forM12[in]
forM16[in]
M12 60 M16 60 0.630 0.866
M12 75 M16 75 0.630 0.866
M12 95 M16 95 0.630 0.866
M12 115 M16 115 0.630 0.866
M12 135 M16 135 0.630 0.866perm. load: 5 kips
Order example: SPH - A4 - M 12 x 75
GV
Itemdescription
Stainless steel
A4
Itemdescription
forHALFEN Bolt
Type Dimensions
SIC - 50/30 - GV SIC - 50/30 - A4 50/30 M16, M20
SIC - 40/22 - GV SIC - 40/22 - A438/1740/22
M16
SIC - 38/23 - GV 38/23 M16
SIC - 29/20 - GV 29/20 M12
SIC - 38/17 - GV SIC - 38/17 - A438/1740/22
M12, M10
SIC - 28/15 - GV SIC - 28/15 - A4 28/15 M8, M10
SIC - 20/12 - GV SIC - 20/12 - A4 20/12 M8
Order example: SIC - 38/17- GV
GVC 15 E
thread size
d load capacity
[in]
[kips]
M 8 0.787 0.31
M 10 0.984 0.52
M 12 1.181 0.76
M 16 1.378 1.57
M 20 1.575 2.70
Recomm. maximum working load at centric-pull
according to DIN 582
VUSsquare washers FV
thread size
Stainless steelA4
thread size
a x b x d
[in]
VUS 40/25for profiles40/25;HZA41/22
M 10 M 10 1.575 x 1.575 x 0.197M 12 M 12 1.575 x 1.575 x 0.197
M 16 M 16 1.575 x 1.575 x 0.197
VUS 49/30for profiles54/33,49/30
M 10 M 10 1.457 x 1.457 x 0.197
M 12 M 12 1.457 x 1.457 x 0.197
M 16 M 16 1.457 x 1.457 x 0.197
M 20 M 20 1.457 x 1.457 x 0.197
VUS 52/34for profiles52/34,50/30
M 16 M 16 1.969 x 1.969 x 0.236
M 20 M 20 1.969 x 1.969 x 0.236
VUS 72/49for profiles72/48,72/49
M 20 M 20 2.126x 2.126x 0.236
M 24 M 24 2.126x 2.126x 0.236
M 27 M 27 2.126x 2.126x 0.236
M 30 M 30 2.126x 2.126x 0.236
VUS 41/41for all 41 profiles
M 6 M 6 1.575 x 1.575 x 0.236
M 10 M 10 1.575 x 1.575 x 0.236
M 12 M 12 1.575 x 1.575 x 0.236
Order example: VUS 52/34 - FV - M 20
perm. load: 10 kips
HALFEN FRAMING AND MOUNTING SYSTEMS
Couplers, Ring nuts, Square washers
VBM
Coupler, round
SKMHexagonal rod
Coupler with
view hole
SPHTurnbuckle
(right and left-
hand thread)
SIC
Locking plate
Application:
To prevent T-bolts
turning during assembly.
RM
Ring-nut
(DIN 582Issue date 2003-8)
f = min.Screw-in depthM12 = 10 mmM16= 13 mm
Assembly Diagram:
HALFEN Channel
HALFEN Bolt
Locking plate SIC
-
8/21/2019 Halfen Mt Fbc Us
46/6846 2012 HALFEN MT-FBC 10-US www.halfenusa.com46
Order no.
Description Item no. For
0318.000- Channel
HPE 63/63 00010 63/63
HPE 52/34 00001 52/34
HPE 50/40 00002 50/40
HPE 41/41 00003 41/41
HPE 41/22 00004 41/22
HPE 36/36 00005 36/36HPE 28/28 00006 28/28
HPE 28/15 00011 28/15
HPE 26/26 00007 26/26
Order-no.
Type length Item-no.
0321.000-PA - 41 - KS 9' 10" 00002
PA - 41 - SV 9' 10" 00001
PA - 22 - KS 9' 10" 00003
PA - 18H - KS 9' 10" 00004
Type overview
Type: PA 41 PA 22 PA 18 H
Material:hard PVC
(KS)
1.614
0.827
0.3
54
1.083"
0.866"
0.5
91"
1.083"
0.1
9
7"
white medium gray medium gray
Material:Steel
pre-galvanized(SV)
1.614
0.827
.354
suitable for profiles:50/40, 50/30, 486,
all 41 profiles
suitable for profile52/34
suitable for profile36/36, 38/17
HALFENHALFEN
PA 2 2
0.5
91
HALFEN FRAMING AND MOUNTING SYSTEMS
Channel end caps, Channel cover s t r ip
Assembly diagramChannel end caps in plastic
Type HPE 63/63
color: blue
Type HPE
color: black
Type HPE 41/41
Type HPE 41/22
color: black
Type HPE 63/63
Type HPE
Type HPE 41/41
Type HPE 41/22
HALFEN Channel
for example;
HM 52/34
The channel cover PAis used to prevent dirt entering the continuous channel opening.Assembly diagram
Channel end caps, HPE
Channel cover PA
0.650
-
8/21/2019 Halfen Mt Fbc Us
47/68 47 2012 HALFEN MT-FBC 10-US www.halfenusa.com 47
HALFEN FRAMING AND MOUNTING SYSTEMS
Cant i levers
Flexible comprehensive support system
Short assembly times
Heavy duty framing system Medium duty framing system Light duty framing system
The flexibility of HALFEN cantilevers
and T-bolts makes them ideal when
the exact positions and sizes of
supports are not finalized at the plann-
ing stage of a project.
Using the HALFEN product range
avoids costly and complex adjustment
work, drilling or thread cutting, in
components which may already be
corrosion protected.
Whether for low or very high perfor-
mance requirements, you are guaran-
teed to find an effective solution in the
HALFEN product range. Using adjustable
bolt connections, components can be in-
stalled, dismantled, moved and adjusted
quickly and simply.
Pipe supports with cantilever brackets in a sewage treatment plant
Note: Depending on the number of
items ordered, custom cantilevers are
available
Canti levers KON
KON 28/1
KON 36/1
KON 36/2
KON 41/1
KON 41/D
KON 41/2
KON 52/2
You can find detailed information on cantilevers in our catalogue;
Adjustable Framing constructions: "HALFEN Adjustable framing
construction systems product information, MT-FFC".
-
8/21/2019 Halfen Mt Fbc Us
48/6848 2012 HALFEN MT-FBC 10-US www.halfenusa.com48
HALFEN Channels Heavy Duty Framing Systems Medium Duty Framing Systems Light Duty Framing Systems
Type:
Order code Pages 1226 Pages 2735Pages 3643
WBhot-rolled:
Material to ASTM A 283, Gr.D
cold-rolled:Material to ASTM A 283, Gr.C
mill finish
Type HZM: to ASTM A 283, Gr.D
Material