GESAMTKATALOG - Linnhoff & Partner...Solutions individuelles pour la galvanoplastie CATALOGUE...
Transcript of GESAMTKATALOG - Linnhoff & Partner...Solutions individuelles pour la galvanoplastie CATALOGUE...
Individuelle Lösungen für die GalvanotechnikCustomized solutions for the electroplating industry
Solutions individuelles pour la galvanoplastie
CATALOGUE INTÉGRALTonneaux de galvanoplastie, groupes et contacts courant fort
GESAMTKATALOG Galvaniktrommeln, Aggregate & Hochstromkontakte
COMPLETE CATALOGUE Plating Barrels, Aggregats & High Current Contacts
Galvaniktrommeln & Aggregate
Über uns 4
Trommelaggregate 6
Trommelwerkstoffe 8
Lagerungssysteme 9
Kontaktsysteme 14
Kontaktkabel 16
Deckelsysteme 18
Perforationen 20
Siebstopfen 22
Kleintrommelaggregate 24
Stangentrommelaggregate 26
Drehgestelle 28
Drehkontaktierungen 29
Beiz- und Phosphatiertrommeln aus Edelstahl 30
Automatische Deckelöffnungs- u. Schließstation (DOS) 31
Elektropoliertrommelaggregate 32
Motorstromkontakte 34
Kunststoffablagen 34
Rohrtrommelkörper 35
Zahnräder 36
English complete catalogue: Barrel aggregates and plating barrels 52
Catalogue intégral en français : Tonneaux de galvanoplastie et groupes 102
Hochstromkontakte
Hochstromkontakte 37
Flächenkontakte 38
Flächenkontakte pneumatisch und wassergekühlt 40
Umrüstung der bestehenden Kontaktierung 42
Fingerkontakte 43
Sonderformen und Ablagen 44
Reinigungsvorrichtungen 46
Anschlusskabel und Strombänder 48
Kunststoffablagen 48
Kupferverschienungen 49
Modulbaugruppen 50
Anodenkörbe 50
Kontaktkabel 51
Gestelltechnik 51
English complete catalogue: High-Current Contacts 87
Catalogue intégral en français : contacts courant fort 137
2 3Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DEHochstromkontakte
DE
EN
FR
Seite 52
Seite 102
Seite 4
DE
EN
FR
Seite 52
Seite 102
Seite 4
Wir sind ein mittelständisches Unternehmen mit Sitz in Iserlohn (Sauerland). Jahrelange Erfahrungen machen uns zum Spezialisten für Galvano- und Hochstromtechnik.
Unser gesamtes Team zeichnet sich durch langjährige Erfahrung bei der Planung, Entwick-lung und Herstellung von individuellen Lösungen aus.
Kundenspezifische Beratung wird bei uns groß geschrieben, damit wir mit Ihnen die passen-den Produkte ermitteln können.
Kompetenz, Engagement und Ideen sind die solide Basis unseres Unternehmens. Die von uns gefertigten Produkte verfügen über einen hohen Qualitätsstandard und zeichnen sich durch extreme Haltbarkeit aus.
Als kompetenter Partner bieten wir Ihnen intelligente und maßgeschneiderte Lösungen für alle Bereiche der Galvanik an.
Individuelle Lösungen für die Galvanotechnik
Trommelaggregateund Galvaniktrommeln
Ideen für Galvano- und Hochstromtechnik!
4 Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Galvaniktrommeln & Aggregate DE
Wir planen, konstruieren und fertigen Trommelaggregate passend zu Ihrer Anlage, so dass Sie unterbrechungsfrei arbeiten können. Mit perfekt aufeinander abgestimmten Komponenten liefern wir immer die richtige Lösung für Ihre Anwendungen. Ausführung als Einzel-, Doppel-trommelaggregat oder Sonderkonstruktion.
• SEW Stirnradgetriebemotoren• Mit Schutzlack OS3• Sonderausführungen• Drehzahl- und Pendelsteuerung möglich• Optional mit Bremse
TrommelaggregateTrommelantrieb
Transportaufnahmen
Kontaktierung
Lagerung
Trommelträger
Schutzhaube
• Transportaufnahmen für Kettenzüge oder Laufwagen• Motorstromkontaktierung im Laufwagen auf Wunsch
• Standard Messerkontakte • Federnde Motorstromkontakte• Reinigungsvorrichtungen für saubere Kontaktierungen• Optional Verbindungsschiene für Potentialausgleich• Andere Aufnahmen auf Wunsch lieferbar• Großes Programm an Standardtypen
• Lagerung als Kunststoffgleitlager oder flüssigkeitsfestes Metallgleitlager.
• Galvanisierstromübertragung über Kabel, Scheibe, Knopf, Leiste ... (weitere Informationen auf Seite 14)
• Verwindungsfreie Stahl- oder Edelstahlkonstruktion• Korrosionsfest epoxydbeschichtet, gebeizt und passiviert oder gummiert• Alle Träger individuell nach Wunsch ausgeführt.
• Motor- und Getriebeschutz aus Polypropylen• Schutz vor Prozesslösungen und Dämpfen
6 7Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Kunststoff-Gleitlagermit Kabelkontakt
• Solider Stahlarm • Fest mit der Trommel verbundene Kontaktscheibe • Mitdrehender Faltenbalg• Spezielles Kontaktfluid im Inneren des Faltenbalgs• Verschleißfreie, statische Dichtungen
Lagerungssysteme
• Austauschbare Lagerzapfen und -buchsen• Flexible Kontaktkabel• Kontaktbirne aus Stahl, Edelstahl, Messing... • Laufbuchsen mit Ablaufbohrungen
Flüssigkeitsfestes Metall-Gleitlager mit Scheibenkontakt
Volumetrische VerschleißwerteVerschiedene Werkstoffe im Vergleich
Werkstoff Dichte p in Kg/m3 Verschleiß
PE 1000 0,93 100
Stahl St 37 7,85 160
PE 500 0,96 300
PP 0,92 600
PVC-hart 1,43 900
Buchenholz 0,83 2.700
TrommelwerkstoffeAbhängig von den chemischen und thermischen Belastungsparametern verwenden wir als Trommelwerkstoff PP, PE 500 oder ultrahochmolekulares Polyethylen PE 1000. Auch Trommeln aus PPs und PVDF sind möglich.
Trommelwerkstoff PP grau
Trommelwerkstoff PE 500 natur
Trommelwerkstoff PE 1000 natur
• Glatte, wasserabweisende Oberfläche• Resistent gegen chemischen Angriff • Abriebbeständig • Schlagfest • Bis 80 °C temperaturbelastbar • Schweißbar
• Glatte, wasserabweisende Oberfläche • Resistent gegen chemischen Angriff • Gute Abriebbeständigkeit• Besonders schlagfest • Bis 90 °C temperaturbelastbar • Schweißbar
• Glatte, extrem wasserabweisende Oberfläche • Resistent gegen chemischen Angriff • Extrem abriebbeständig • Absolut schlagfest • Bis 100 °C temperaturbelastbar
8 9Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
12
13
14
15
1
4
3
2
5 8
6
17
11 10
9
7
16
19
18
KunststoffgleitlagerEinzelteile für das Kunststoffgleitlager mit Zwischenradlager und Zahnrad.
Pos. Bezeichnung Werkstoff
1 Flansch (80 x 20 x 150 f. K-Gleitlager) 1.4301
2 Stehbolzen (l = nach Angabe) C45
3 Schraube (M 12 x 25 – DIN 912) 1.4571
4 Mantelrohr (l = nach Angabe) PP
5 Laufzapfenaufnahme PE
6 Laufzapfen PE
7 Zylinderkerbstift (d = 10 x 30 – DIN 1473) PVC
8 Anlaufring PE
9 Laufbuchse PE
10 Schraube (M 16 x 40) PE
11 O-Ring (10,77 x 2,62 – ARP 111) Perbunan
12 Zwischenradblock (150 x 143,3 x 76) PP Gv natur
13 Schraube (M 12 – DIN 933) 1.4571
14 U-Scheibe (13,0 – DIN 7349) 1.4571
15 Dichtschraube PP
16 Lagerbuchse PTFE
17 Zahnrad (Modul u. Zähnezahl nach Angabe) PE 1000 natur
18 Arretierungsscheibe PE 1000 natur
19 Schraube (M 8 x 30 – DIN 7991) 1.4571
10 11Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Einzelteile für das flüssigkeitsfeste Metallgleitlager mit Scheibenkontakt und Zwischenradlager mit Zahnrad.
23
25
22
Flüssigkeitsfestes Metall-Gleitlager mit Scheibenkontakt
1
24
19
20
18
17
16
15 14
9
12
13
11
108
7
6
2
21
5
27
3 4
26
Pos. Bezeichnung Werkstoff
1 Tragarm mit Flansch 1.4301/St.
2 Lamellenband – LA1 Cu-Ag
3 Druckfeder 1.1200
4 Kontaktstift Cu
5 Faltenrohr mit Rechtsgewinde PE 1000 natur
6 Ausgleichsflansch PE 1000 natur
7 Lagerbuchse Bz-Si
8 Kontaktscheibe Bz
9 Lagerflansch St
10 Dichtring Paragummi
11 Kontaktscheibe St 37 vernickelt
12 Flansch + O-Ring 1.4571 + Perbunan / Viton
13 Verschlussscheibe + O-Ring PE 1000 natur + Perbunan / Viton
14 Schraube (M 10 x 20 spez.) + O-Ring 1.4571 + Perbunan / Viton
15 Abdeckkappe PP
16 Schraube (M 10 x 25 – DIN 933) 1.4571
17 O-Ring (129,54 x 5,33) Perbunan
18 Dichtschraube PP
19 Schraube (M 12 – DIN 933) + Federring 1.4571/St
20 U-Scheibe (13 – DIN 7349) 1.4571
21 Zwischenradlagerblock (h = nach Angabe) PP Gv
22 Zahnrad (Modul und Zähnezahl nach Angabe) PE 1000 natur
23 Arretierungsscheibe PE 1000 natur
24 Schraube (M 8 x 30 – DIN 7991) 1.4571
25 Lagerbuchse PTFE
26 Bolzen 1.4301
27 Sicherungsstift PE 1000 natur
12 13Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
KontaktsystemeUm Ihnen die für Ihr Warenspektrum optimale Kontaktierung liefern zu können, haben wir verschiedene Standardlösungen entwickelt.
Kabelkontakt mit KunststoffgleitlagerKontaktkabel sind die kostengünstigsten und häufigsten Kontaktierungen. Sie eignen sich besonders für kompaktes Schüttgut und decken somit einen breiten Einsatzbereich ab. Auch mit Hohlbirne und Sonderformen erhältlich.
Scheibenkontakt mit MetallgleitlagerScheibenkontakte sind sehr gut geeignet für hohe Strom-übertragungen. Sie sind einsetzbar für sperrige, kompakte und scharfkantige Waren sowie empfindliche Güter, die durch feststehende Kontakte beschädigt werden könnten.
Kabelkontakt mit Kunststoffgleitlager und durchgehender BirneKontaktkabel mit durchgehender Birne haben eine größere Oberfläche zum verbesserten Kontaktieren der Ware.Dank der frei hängenden Kontaktbirne findet kein Schlagen auf die Ware statt. Diese Eigenschaft macht diesen Typ besonders für empfindliche Ware interessant.
Leichter Einbau, geringer Wartungsaufwand. Auch mit geschraubter Kontaktbirne für schnelles Austauschen und als Hohlbirne für besonders empfindliche Ware erhältlich.Kostengünstige Alternative zur Leistenkontaktierung.
Leistenkontakt mit MetallgleitlagerLeistenkontakte sind in den Trommeleckstäben eingelegt und übertragen den Strom vom flüssigkeitsfestem Metall-gleitlager über Kontaktscheiben gleichmäßig auf die gesamte Innenlänge der Trommel. Der Trommelinnenraum bleibt dabei glatt. Mit Leistenkontakten lässt sich ein umfangreiches Warenspektrum galvanisieren. Diese Kontaktierung eignet sich besonders gut für Stangenware.
Universalkontaktanschlüsse mitMetallgleitlagerUniversalkontaktanschlüsse bieten die Möglichkeit, zahlrei-che verschiedene Kontaktarten wahlweise einzusetzen und bei Bedarf schnell zu wechseln. Kundenspezifische Sonder-kontakte lassen sich problemlos realisieren.
Knopfkontakt mit MetallgleitlagerKnopfkontakte bieten ebenso wie Leistenkontakte eine gleichmäßige Stromübertragung über die gesamte Trommel-innenlänge. Sie sind in besonderem Maße geeignet für empfindliche Ware, die durch feststehende Kontakte be-schädigt werden könnte. Zusätzlich gewährleisten sie selbst bei minimal gefüllter Trommel eine einwandfreie Stromüber-tragung. Die Knopfkontakte sind leicht austauschbar.
14 15Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Unsere langlebigen Kontaktkabel werden standardmäßig aus PUR-Mantelleitung gefertigt. Die speziell für uns gefertigte Leitung ist in verschiedenen Durchmessern und Querschnitten erhältlich. Auch Sonderanwendungen wie PVC, Silikon und Neoprenleitungen sind möglich.
Unsere „Kontaktbirnen“ gibt es wahlweise aus Stahl, Messing, Edelstahl oder Sonderwerkstoffen, wie Titan oder Kupfer. Die Ausführung kann hohl, schraubbar, durchgehend oder in weiteren Sonderformen erfolgen. Lassen Sie sich individuell beraten und erhöhen Sie die Lebensdauer dieses Verschleißartikels.
Kontaktkabel
Kabelschuh / Anschluss• geschlossener Rohrkabelschuh in schmaler Ausführung um ein problemloses
Einführen des Kabels durch den Laufzapfen/die Laufbuchse zu ermöglichen• alle gängigen Anschlussbohrungen
AbdichtungEs stehen 2 Varianten der Abdichtung zur Verfügung:• Mit einer Gummitülle wird das Kabel gegen Spritzwasser und Staub geschützt.• Durch Einsatz einer VA-Dichthülse kann das Kabel flüssigkeitsdicht verschlossen werden.
KabelDie widerstandsfähige PUR Mantelleitung zeichnet sichdurch eine hohe Haltbarkeit aus. Sie steht in folgenden Querschnitt/Durchmesser Kombinationen zur Verfügung:• Ø14: 35mm²• Ø20: 50mm²; 95mm²• Ø25: 95mm²• Ø28: 120mm²• Ø29: 150mm²• Ø30: 120mm²; 185mm²• Ø32: 240mm²
Kontaktbirne• Standardmäßig führen wir Kontaktbirnen
in Stahl, VA oder Messing.• Durch die 8-fach Verpressung mit mehreren
Tonnen Druck ergibt sich eine dichte Verbindung mit dem Kabelmantel
• Wahlweise kann die Kontaktbirne zum schnellen Austausch auch geschraubt ausgeführt werden
Ein Anfrageformular für Kontaktkabel finden Sie im Internet unter: www.linnhoff-partner.com/downloads
16 17Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Alle Deckelsysteme können manuell oder automatisch geöffnet und geschlossen werden.
Deckelsysteme
Deckelsystem mit Deckelnut in L-FormEinfache Ausführung eines dicht schließenden Systems. Oftmals findet dieses Deckelsystem in Altanlagen Verwendung. Es ist geeignet für die meisten Warenspektren.
Deckelsystem mit Deckelnut in VK-FormDieses System ist das zur Zeit am meisten Verbaute. Auch abrasive und spitze Teile dringen nicht in die Nut ein.
Deckelsystem mit Deckelnut in V-FormÄhnliche Eigenschaften wie bei der VK-Form, jedoch nur für feine, nicht abrasive Teile geeignet.
18 19Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
SchlitzperforationDurch überschneidende Fräsung der Schlitze bleibt die Sta-bilität der einzelnen Mantelplatten erhalten und die außerge-wöhnliche Werkstoffqualität der Trommel ermöglicht die sehr dichte Perforierung, somit sind auch höhere Stückge-wichte kein Problem.
SichelperforationVon allen Perforationen ist die Sichelperforation für das breiteste Warenspektrum geeignet (Bsp.: Nägel, Schrauben, Münzen, Blech-, Stanz- und Biegeteile, uvm.). Die wesentlich größere Öffnungsfläche von bis zu + 30% (beispielsweise gegenüber einer gleichwertigen Rundperforation) garantiert einen verbesserten Elektrolytaustausch. Mit speziellen Fräsern kann die Sichelperforation in Mantelplatten bis 20 mm problemlos eingebracht werden, dadurch ergibt sich eine wesentliche Erhöhung der Standzeiten. Die konische Form nach außen ermöglicht ein schnelles Eindringen sowie ein schnelles Auslaufen des Elektrolyten.
LanglochperforationÄhnlich beschaffen wie die Sichelperforation, bietet die Lang-lochperforation gleiche Vorteile. Sie wurde entwickelt als Ersatz zur gesägten Schlitzperforation, da durch die formsta-bile Geometrie ein Aufweiten der Perforation vermieden wird.
PerforationenDie Qualität und Wirtschaftlichkeit der Trommelgalvanisierung hängt in erheblichem Maße von der Art und Größe der Perforation ab. Zur Auswahl der optimalen Perforation steht eine breite Palette zur Verfügung.
RundperforationDie außergewöhnliche Werkstoffqualität der Trommel ermöglicht eine sehr dichte Perforierung. Ansenkungen bzw. Ein-fräsungen innen und außen fördern den Elektrolytaustausch, verringern den Spannungsabfall in der Wandung, reduzieren Schleppungsverluste und verhindern das Ankleben flacher Teile in der feuchten Trommel.
Besonderheiten:• Sehr enger Lochabstand• Beidseitig angesenkt• Optional kann auch für klebende Teile überschneidend gesenkt werden
20 21Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Unsere Siebstopfen haben sich im jahrelangen Einsatz bewährt, nicht nur im Bereich der Trommeltechnik. Mittlerweile werden unsere Stopfen auch in Filteranlagen und Siebplatten eingesetzt. In der großen Palette an Perforationen und Ausführungen, findet sich auch für Ihr Einsatzgebiet der passende Stopfen.
Unser Siebstopfen-Perforationssystem bietet Ihnen folgende entscheidende Vorteile:
• Leichter Austausch* der Siebstopfen für eine optimale Anpassung an die Ware• Durch die Wölbung der Siebstopfenkappe wird das Ankleben flacher Teile verhindert• Der Siebgewebecharakter mindert Spannungsabfälle und Verschleppungsverluste• Nach außen gerichtete große Eintopfungen sorgen mit zusätzlichem Pumpeffekt für einen optimalen Elektrolytaustausch
* Der Siebstopfen ist danach nicht wiederverwendbar.
A-Siebstopfen Sortiment ca. 40 mm / Werkstoff: PP
E-Siebstopfen Sortiment ca. 23 mm / Werkstoff: PP
Standard
Konkav
Konvex
Siebstopfen
Pos. Bezeichnung Artikel-Nr.
1 0,25 Schlitz 90000100
2 0,4 Schlitz 90064500
3 0,6 Schlitz 90117800
4 1,3 Schlitz 90018400
5 1,3 Schlitz konkav 90081800
6 1 x 1 90000400
7 1,75 x 1,75 90070300
8 2 x 2 90000500
9 2 x 2, konvex 90000700
10 2 x 2, konkav 90037950
11 3 x 3 90000800
12 3 x 3 konvex 90000900
13 8 x 8 konvex 90018300
14 0,25 Schlitz mit 2 x 2 Raster 90000300
15 Sichelsiebstopfen 1,3 mm 90823700
Pos. Bezeichnung Artikel-Nr.
1 0,25 Schlitz 90001300
2 0,4 Schlitz 90019500
3 0,4 x 0,4 90117600
4 1 x 1 90017100
5 1 x 1 konvex 90001400
6 2 x 2 90098900
22 23Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Zum rationellen Veredeln von Kleinserien oder Kleinteilen entwickelt, findet unsere Kleintrommelserie große Verwen-dung in vielen Bereichen. Die leichte Handhabung und das geringe Eigengewicht dieser Baureihe ermöglichen Char-gengewichte bis 13 kg. Bei Einsatz eines Kettenzuges erhöht sich das Gewicht pro Charge auf bis zu 30 kg.
In der Standard-Ausführung wird der Trommelkörper aus Polypropylen gefertigt, jedoch sind auch Sonderausführun-gen in anderen Werkstoffen möglich. Beispielsweise wurden im Chemisch-Nickel Bereich beste Ergebnisse mit PVDF Trommeln erreicht.
Um Verschleppungsverluste auf ein Minimum zu reduzieren wird der gesamte Trommelkörper verschweißt und die Nähte werden geglättet. Dies verhindert ebenso ein Hängenbleiben der Ware. Eine spe-zielle Rillenstruktur an den Stirnwänden wirkt dem Ankleben von flacher Ware entgegen. Dank der groß dimensionierten Deckelöffnung ist ein einfaches Be- und Entladen möglich.
Der hier angebrachte Deckelverschluss sorgt für höchste Betriebssicherheit und
einfache Bedienung. Deckelsitz und Deckelform sind so konstruiert, dass ein Eindringen kleiner Teile zwischen Deckel und Trommelkörper verhindert wird.
Zur Übertragung des Galvanisierstroms auf die Ware kann aus verschiedensten Kontaktierungen gewählt werden. Als Beispiel finden sich hier der klassische Kabelkontakt, sowie auch Scheibenkontakte, Knopfkontakte, Stiftkontakte und viele weitere Möglichkeiten.
Ebenfalls besteht die Möglichkeit des netzunabhängigen Akkubetriebs mit Dockingstation sowie Ausrüstung des Aggregats mit einer Pendel-, Reversier- und/oder Vibrati-onseinheit. Um den Elektrolytaustausch zu verbessern, kann außerdem eine Elektrolyteinspritzung verbaut werden.
Rundum ist die Kleintrommelserie der optimale Partner für rationelles Veredeln. In den Bereichen Elektronikbauteile, Schmuckindustrie, Kleinserien, Lohngalvanik, Forschung und Entwicklung ist die Kleintrommel unabdingbar.
Kleintrommelaggregate
24 25Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Speziell für stangenförmiges „flaches oder rundes“ Material entwickelt, können die Aggrega-te als Einfach- oder Doppeltrommelaggregate ausgelegt werden. Durch den Einsatz von herausnehmbaren Zwischenwänden ist die Trommel in mehrere nutzbare Abschnitte unter-teilbar. Ausgelegt sind die Aggregate für Chargengewichte von über 300 kg und Längen bis zu 2500 mm.
Schutzhaube
Warenkörbe mit Kontaktierung
Verstellbare Stirnwände
Korböffnung
• Motor- und Getriebeschutz aus Polypropylen• Schutz vor Prozesslösungen und Dämpfen
• Zur Kontaktierung werden Stiftkontakte eingesetzt, welche mittig in den Aufnahmekörben sitzen. Diese Kontaktstifte können einseitig, beidseitig oder durchgehend ausgeführt werden und sind einzeln austauschbar.
• Für unterschiedliche Waren können verschiedene Geometrien in die Korböffnung eingebracht werden, beispielsweise 6-eck oder 4-eck. Standardmäßig sind die Körbe mit einer runden Geometrie ausgestattet.
• Die groß dimensionierte Korböffnung mit 135° Öffnungs-winkel ermöglicht ein leichtes Befüllen der Körbe.
Stangentrommelaggregate
• Durch den Einsatz von herausnehmbaren und verstellbaren Zwischenwänden kann die Trommel in mehrere nutzbare Abschnitte unterteilt werden. Die Verstellung der Zwi-schenwände erfolgt über einen Pressstift, wodurch sich eine formschlüssige Fixierung ergibt.
Transportaufnahmen
Kontaktierung
Lagerung
Trommelträger
• Transportaufnahmen für Kettenzüge oder Laufwagen• Motorstromkontaktierung im Laufwagen auf Wunsch
• Standard Messerkontakte • Federnde Motorstromkontakte• Reinigungsvorrichtungen für saubere Kontaktierungen• Optional Verbindungsschiene für Potentialausgleich• Andere Aufnahmen auf Wunsch lieferbar• Großes Programm an Standardtypen
• Flüssigkeitsfestes Metallgleitlager.
• Verwindungsfreie Stahl- oder Edelstahlkonstruktion• Korrosionsfest epoxydbeschichtet, gebeizt und passiviert oder gummiert• Alle Träger individuell nach Wunsch ausgeführt.
• SEW Stirnradgetriebemotoren• Mit Schutzlack OS3• Sonderausführungen• Drehzahl- und Pendelsteuerung möglich• Optional mit Bremse
Trommelantrieb
26 27Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Drehgestelle stromlos und stromführend DrehkontaktierungenFür Bauteile mit ungünstigen Geometrien wie Sacklöchern, Hinterschneidungen oder Taschen, in denen sich Luftblasen bilden können, sind unsere Drehgestelle die perfekte Lösung. Die Ware wird hierbei in speziellen Vorrichtungen einzeln
aufgenommen oder alternativ in Körben mit dem Gestell adaptiert. Somit ist eine gleichmäßige Behandlung möglich und Beschädigungen werden minimiert.
Ein weiterer Bereich sind die stromführenden Drehkontaktie-rungen, welche für die Aufnahme von ein bis maximal zwei Werkstücken konzipiert sind. Diese Drehkontaktierungen finden häufig Einsatz im Bereich des Galvanoforming oder bei Hartchromverfahren. Beispielhafte Anwendungen sind
das Beschichten von Prägewalzen oder Kolbenstangen. Stückgewichte von mehreren hundert Kilogramm sind hier keine Seltenheit. Lassen Sie sich für Ihren Anwendungsbe-reich persönlich beraten und vereinbaren Sie einen Termin.
28 29Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Diese Aggregate werden speziell nach Kundenwunsch gefertigt. Die Perforation ist nach Ihren Wünschen ausleg-bar. Trommelträger und Schutzhauben werden aus unserem
Standardprogramm verwendet. Trommelkörper und Lager-holme werden aus Edelstahl, wahlweise 1.4301, 1.4401 oder 1.4571 gefertigt.
Automatische Deckelöffnungs- und Schließstation (DOS) Ablaufvorgang bei der DeckelöffnungDie Deckelöffnungsvorrichtung fährt die Galvanisiertrommel in der Be- und Entladestation eigenständig an, bringt sich in Vorposition und wird anschließend feinpositioniert. Nach der eben beschriebenen Positionierung setzt nun der eigentliche Deckelöffnungsvorgang ein.
Durch das Ausfahren des Hubzylinders werden die Deckelöffnungswerkzeuge in Schräglage gebracht und greifen in die Aussparungen der Deckelknebel. Die Konstruktion der Greifwerkzeuge gewährleistet zum einen das reibungslose Greifen der Knebel und zum anderen das sichere Halten des Deckels in der Deckelöffnungsvorrichtung.
Da die Deckelöffnungswerkzeuge durch einen Flachstab miteinander verbunden sind, ist sichergestellt, dass der Neigungs-winkel der einzelnen Werkzeuge zu jeder Zeit absolut identisch ist.
Nachdem nun der Deckel durch die Öffnungsvorrichtung aufgenommen ist, bewegt sich die Vorrichtung mitsamt Deckel in die Ausgangsposition zurück. Die Trommel kann nun ungehindert be- bzw. entladen werden.
Durch die einfache Konstruktion dieser Be- und Entladestation werden Bewegungsvorgänge auf ein Minimum reduziert. Dadurch ergeben sich eine Reihe entscheidender Vorteile im Bezug auf Wirtschaftlichkeit, Zuverlässigkeit und Langlebigkeit. Funktionsprinzip LINNHOFF & PARTNER
Ablaufvorgang beim Schließen des DeckelsDas Schließen des Deckels geschieht analog zur Deckelöffnung, nur in umgekehrter Reihenfolge. Die Vorrichtung befördert den Deckel immer zuverlässig und exakt in die Trommelöffnung zurück.
Beiz- und Phosphatiertrommeln aus Edelstahl
30 31Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Die Firma Linnhoff & Partner Galvanotechnik hat bei diesem neuartigen Konzept einer Elektropoliertrommel ein besonde-res Augenmerk auf die Qualität der fertigen Ware gelegt. Mit der EP-Trommel ist es erstmalig möglich, Ware mit einem maximalen Volumen von 8 Litern bzw. einem maxi-malen Gewicht von 25 kg in gleicher und höchster Qualität zu elektropolieren.
Die Vorteile dieser Trommel im Überblick: • Sorgfältige Verarbeitung unter Einsatz hochwertiger Werkstoffe garantiert eine hohe Lebensdauer auch
bei starker Belastung• Solide, werkstoffgerechte Systembauweise • Ein passgenauer und dicht schließender Deckel • Anwenderfreundliche Bedienbarkeit und Betriebssicher-
heit, die aufgrund des Deckelverschlusssystems auch höchsten Ansprüchen gerecht wird • Stabile Lagerung • Optimaler Elektrolytaustausch und minimierter
Verschleppungsverlust durch glatte, wasserabweisende Materialoberflächen und spaltenfreie Übergänge in
Verbindung mit einem ausgefeilten Perforationssystem
Bei einer Befüllung von 80% des Trommelvolumens (ca. 8 Liter), beträgt der zugeführte Strom ca. 500 Ampere bei 6 bis 10 Volt Spannung. Der Zyklus zum Elektropolieren beträgt zwischen 1 und 15 Minuten – je nach Zustand des Vormate-rials. Dank der extra entwickelten Steuerelektronik ist eine stufenlose Drehzahleinstellung sowie ein Pendelbetrieb möglich.
Die flüssigkeitsfesten Metallgleitlager übertragen den Strom direkt auf den Titan- bzw. Edelstahltrommelkörper. Das spe-zielle Kontaktfluid im Inneren der Lager hält die Kontaktflä-chen sauber. Dieses System erlaubt Stromübertragungen bis 500 Ampere pro Seite.
Der doppelwandige Trommelkörper und das doppelwandige Zentralrohr sind absolut kurzschlusssicher. Eine Wandung überträgt dabei den Anodenstrom, die andere den Katho-denstrom.
AntriebWir verwenden für den Antrieb qualitativ hochwertige Stirn-radgetriebemotoren mit Schutzschalter. Die Motorspannung beträgt 12 oder 24 Volt Gleichstrom. Zudem lässt sich die Trommeldrehzahl stufenlos am Aggregat einstellen.
KontaktauflageZur Warenstromübertragung verwenden wir standard-mäßig Messerkontakte aus Kupfer, die auch für hohe Ströme geeignet sind.
TrommelkörperDer Trommelkörper wird aus Titan und Edelstahl 1.4571 gefertigt. Das flüssigkeitsfeste Metallgleitlager ermöglicht eine Stromübertragung von bis zu 500 A. Die spezielle Form des Deckels garantiert einen spaltfreien Sitz. Mit den hand-lichen Deckelknebeln lässt sich der Deckel leicht öffnen und schließen.
TransportaufnahmenDie Transportaufnahme für die EP-Trommel ist mit einer Lastöse ausgestattet. Auf Wunsch liefern wir Ihnen aber auch andere Transportwagenaufnahmen. Eine Anpassung der Aufnahmen oder des gesamten Trägers ist in den meisten Fällen realisierbar.
Elektropoliertrommelaggregat
32 33Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Der Motorstromkontakt ist ein wichtiger Bestandteil eines gut funktionierenden Trommelaggregates. Unsere Motorstromkon-takte haben entscheidende Vorteile und stellen einen störungsfreien Lauf Ihrer Anlage sicher.
Vorteile:• Selbstreinigende Kontaktflächen• Sehr hohe Stromübertragung (bis zu 60 Ampere)• Äußerst robust und daher sehr betriebssicher• Wartungs- und reparaturfreundlicher Aufbau
Kunststoffablagen fertigen wir meist aus PE oder PP. Sie haben die Wahl zwischen unseren preisgünstigen Stan-dardablagen oder einer auf Sie zugeschnittenen Ablage.
Durch unsere 5-Achsen CNC Zentren sind wir in der Lage auch komplexe Geometrien zu fertigen. Ein Muster oder eine Skizze ist in den meisten Fällen vollkommen ausreichend.
Mit dieser »Trommel in der Trommel« können Sie kleine Chargen galvanisieren, indem Sie den Rohrtrommelkörper einfach in die vorhandene Trommel legen. Der Körper wird aus PP grau gefertigt und hat zur Kontaktierung Schrauben mit Hutmuttern aus Edelstahl. Es stehen zwei Größen mit den Innendurchmessern 50 mm und 100 mm zur Auswahl. Die Länge bestimmen Sie selbst. Beim Trommelkörper mit
100 mm Innendurchmesser sind die Kontakte auch stirnsei-tig angebracht. Die Standardperforation ist rund mit 6 mm Durchmesser.
Sonderperforationen und -formen sind auf Wunsch lieferbar.
Motorstromkontakte
Kunststoffablagen
Rohrtrommelkörper
34 35Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Galvaniktrommeln & Aggregate DE
Unsere Zahnräder werden vom Einzelteil bis zur Kleinserie komplett in unserem Haus gefertigt. Von Antriebszahnrädern für Kleintrommelaggregate bis zu mehrteiligen Zahnradbau-gruppen ist für uns alles möglich.
Den häufigsten Einsatz findet hier PE 1000, aber auch andere Materialien wie PE 500, PP, PPs, VA und viele weitere sind möglich. Ebenso Kombinationen aus Kunststoff und Metall.
Zahnräder Hochstromkontakte &Reinigungsvorrichtungen
Ideen für Galvano- und Hochstromtechnik!
36 Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Hochstromkontakte DE
überzeugen durch ihren einfachen Aufbau. Eine stabile Schweißkonstruktion aus hochwertigem Edelstahl sorgt für einen dauerhaften reibungslosen Einsatz. Die Kontaktplatten werden durch isolierte Federn mit hohem Druck an die Kontaktflächen gepresst, wodurch eine optimale Stromüber-
tragung erreicht wird. Der Anschluss erfolgt mit einfachen Anschlusskabeln direkt auf die Kontaktplatten. Bei Waren-bewegungen sind somit keine zusätzlichen Strombänder erforderlich. Robust, wartungsfreundlich, kostengünstig und selbstreinigend.
Flächenkontakte
Druckfedern• Isolierte Druckfedern aus
Edelstahl für konstanten Druck• Optionale Korrosionsschutz-
beschichtung
Überwachung• Optionale Überwachung
der Kontakte mit PT100 Temperaturfühlern
Schutzhauben• Schutzhauben aus 1.4301
zum Schutz vor herabfallen-der Verschmutzung
Stabile Edelstahlkonstruktion• Trägerkonsole aus 1.4301 mit stabilen
Einweisern als Schweißkonstruktion• Optional aus 1.4571, mit Beschichtung
oder mit zusätzlichen PE-Einweisern
Anschlüsse• Gerade oder gewinkelt zum
leichten Anschluss der Strombänder
Auswechselbare Kontaktplatte• Einfach auszutauschende Kontaktplatten
mit Abstreifnuten zur Selbstreinigung beim Einfahren
38 39
1500 A 3000 A
Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Pneumatisch Pneumatische Kontakte werden nur dort eingesetzt, wo sehr hohe Ströme, sehr wenig Platz oder geringe Einfahrgewichte eine Herausforderung darstellen. Der Anpressdruck wird durch den Einsatz von vulkanisierten Druckkissen erreicht. Bei den pneumatischen Kontakten sind kaum Grenzen gesetzt, Kontakte mit 20 KA und mehr sind keine Seltenheit. Durch eine optionale Wasserkühlung ist eine Leistungserhö-hung jederzeit möglich. Die Kosten sind verhältnismäßig hoch, allerdings wird durch ihren Einsatz ein Höchstmaß an Prozesssicherheit erreicht.
Wassergekühlt Zur Erhöhung der Leistung bei gleichem Bauraum wie ein normaler Flächenkontakt empfiehlt sich der Einsatz einer Wasserkühlung. Dies ermöglicht, je nach Kühlleistung, eine Steigerung des maximalen Stroms um bis zu 35%. Die Wasserkühlung befindet sich direkt in den Anschlussplatten. Zur optimalen Überwachung der Kontakte empfiehlt sich immer der Einsatz von PT100 Temperatursensoren. Somit ist jederzeit ein sicherer Betrieb der Kontakte gewährleistet.
Druckkissen• Pneumatischer Antrieb unter
Einsatz von vulkanisierten Druckkissen
Druckfedern• Isolierte Druckfedern aus
Edelstahl für konstanten Druck• Optionale Korrosionsschutzbe-
schichtung
Isolierplatte• Isolierplatte aus PPs oder HGW
zum Schutz des Druckkissens vor Wärmeeinwirkung
Wasserkühlung• Optionale Wasserkühlung zur
Erhöhung der Leistung
Kontaktplatten• Einfach auszutauschende Kontakt-
platten mit Abstreifnuten zur Selbst- reinigung beim Einfahren
Schutzhauben• Schutzhauben aus 1.4301
zum Schutz vor herabfal-lender Verschmutzung
Anschlüsse• Gerade oder gewinkelt
zum leichten Anschluss der Strombänder
Trägerkonsole• Trägerkonsole aus 1.4301 mit stabilen
Einweisern als Schweißkonstruktion• Optional aus 1.4571, mit Beschichtung
oder mit zusätzlichen PE-Einweisern
Überwachung• Optionale Überwachung
der Kontakte mit PT100 Temperaturfühlern
Flächenkontakte mit pneumatischemAntrieb und Wasserkühlung
40 41Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Die bestehende Kontaktierung lässt sich für jede Anlageindividuell anpassen. Alle unsere Systeme sind in der Praxiserprobt und je nach Ausführung ist eine Vervielfachung der Leistung möglich.
Einfache Umrüstung der bestehenden Kontaktierung
Prismenaufnahme
Kontaktschwert-Aufnahme
Rundzapfenaufnahme
V-Aufnahme
Fingerkontakte mit mehreren federgespannten Einzelfingern sorgen für eine gute Kontaktierung auch bei unebenen Kontaktflächen am Warenträger. Im Idealfall besitzen die Kontaktfinger Abstreifnuten, welche den oberflächlichen
Schmutz beim Einfahren des Warenträgers abreiben. Um die beweglichen Elemente mit dem Grundkörper zu verbinden werden Folienbänder verwendet.
Durch die Verwendung eines Druckkissens in der pneuma-tischen Version des Fingerkontakts ist es möglich, den Kontaktdruck zu erhöhen und somit eine bessere Kontaktie-rung zu erreichen. Besonders bei bestehenden Anlagen
sind die Kontaktoberflächen der Warenträger oft uneben. Hier ist es sinnvoll, die Kontakte mit pneumatischen Fingern zu wählen.
Fingerkontakte
Pneumatisch
42 43Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Sonderformen und Ablagen
BolzenkontakteBolzenkontakte wurden zu Beginn der Automatisierung an Galvanikanlagen eingesetzt. Heute finden Sie immer noch Verwendung als Anodenkontakte und für Elektrolysezellen. Der Grundkörper ist aus massivem Messing und wird direkt auf die Anschlussschiene montiert. Somit entfallen unnötige Verbindungsstellen.
Im Inneren des Kontaktes befinden sich federgelagerte Bolzen in Verbindung mit Kontaktlamellen. Die Höhe des maximalen Stroms hängt von der Anzahl der Kontaktbolzen ab. Jeder Bolzen ist in der Lage, ca. 400A zu übertragen. In den meisten Fällen empfiehlt sich jedoch der Einsatz eines günstigeren Hochstromflächenkontaktes.
Messingablagen werden bereits seit mehr als 100 Jahren eingesetzt. In den Anfängen der industriellen Galvanik wurden neben den Messingablagen lediglich gebogene Federkontakte verwendet. Bei kleinen Strömen bis 500 A
sind diese Kontakte auch heute noch ausreichend. Geringe Kosten und gute mechanische Eigenschaften sind ein Vorteil, leider verfügen sie nicht über einen „Selbstreini-gungseffekt“ und müssen daher ständig gepflegt werden.
Wir fertigen unsere Kontakte nicht ausschließlich für den Bereich der Galvanotechnik. Sonderlösungen finden sich zum Beispiel auch in Wartungsanlagen für Züge, Schnell-wechselsystemen für Presswerkzeuge, Vakuumöfen, Prüffeldern, Recyclinganlagen und Spezialanlagen für die Raumfahrt.
Überall dort, wo hohe Ströme sicher übertragen werden müssen, bieten Sonderkontaktierungen von Linnhoff und Partner die passende Lösung. Jedes Projekt wird in solchen Fällen intensiv mit Ihnen ausgearbeitet bis eine wirtschaft-lich sinnvolle und funktionierende Lösung gefunden ist.
Schlittenkontakte finden sich häufig in Leiterplattengalvani-ken, weil dort nur geringe Einfahrgewichte vorhanden sind. Der Einsatz von Schlittenkontakten erfordert eine hohe Einfahrgenauigkeit und präzise Position der Kontakte. Durch
die nur beschränkten Ausgleichsmöglichkeiten sind diese nicht für 3 oder 4-Punkt Auflagen geeignet. Sowie die Messingablagen verfügen auch die Schlittenkontakte nicht über einen „Selbstreinigungseffekt“.
Sonderkontaktierungen
Schlittenkontakte
Messingablagen
44 45Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Was schon vor 90 Jahren ein Thema war, wird heute doch immer noch oft vergessen. Nur saubere Kontakte können effizient arbeiten.
Zur Unterstützung des Personals empfiehlt sich der Einsatz von Reinigungsvorrichtungen im Bereich der Spülen. Diese Reinigungsvorrichtungen arbeiten unabhängig vom Anla-genbediener. Bei jedem Zyklus werden die Kontaktflächen des Trägers gereinigt.
Auch hier zahlt sich der einfache und solide Aufbau aus. Die Bürsten können einzeln getauscht werden. Reinigungsvor-richtungen gibt es für jeden Kontakttyp (Schwert, Zapfen, Prisma, etc.). In den meisten Fällen können die Reinigungs-vorrichtungen einfach gegen die bestehenden Kunststoffauf-nahmen getauscht werden.
Reinigungsvorrichtungen„Anfänger übersehen häufig die Reinhaltung der Leitungen und Kontakte,
und doch ist dies von ganz besonderer Wichtigkeit für die Stromzirkulation und infolgedessen für die Niederschlagsarbeit.“ Dr. W. Pfanhauser, Galvanotechnik, 1928
Stabile Edelstahlkonstruktion • aus 1.4301• Individuelles Lochbild der Befestigungsbohrungen
gemäß Ihren Anforderungen
Federgelagerte Halteklötze aus PE 1000• Zur Aufnahme der Streifenbürsten• über die Innensechskantschrauben können die
Halteklötze justiert werden
Einzeln austauschbare Bürsten aus 1.4301• Die Streifenbürsten können direkt am Behälter
ausgetauscht werden, es ist kein Ausbau der Reinigungsvorrichtung notwendig.
46 47Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Zum Anschluss der Hochstromkontakte oder auch Gleich-richter empfehlen wir den Einsatz hochflexibler Anschluss-kabel. Diese fertigen wir in verschiedenen Ausführungen und Querschnitten, direkt nach Ihren Anforderungen. Wahlweise bestehen die Kabel aus verpressten Cu-Litzen mit Anschlussflansch oder Kabelschuh. Je nach Anwendungs-bereich und Umgebung werden die Anschlusskabel mit Schutzschläuchen verschiedenster Materialien, wie PVC, Silikon oder PUR, versehen und dicht verpresst. Bei der Auswahl des passenden Kabels stehen wir Ihnen gerne zur Verfügung.
Anschlusskabel und Strombänder
Kunststoffablagen
KupferverschienungenZubehör
Kunststoffablagen fertigen wir meist aus PE oder PP. Sie haben die Wahl zwischen unseren preisgünstigen Stan-dardablagen oder einer auf Sie zugeschnittenen Ablage. Durch unsere 5-Achsen CNC Zentren sind wir in der Lage auch komplexe Geometrien zu fertigen. Ein Muster oder eine Skizze ist in den meisten Fällen vollkommen ausreichend.
Durch den Einsatz moderner und professioneller Stanz- und Biegetechnik sind wir in der Lage, Kupferverschienungen vor Ort zu fertigen und zu montieren. Dabei wird das Roh-material vor Ort geschnitten, gestanzt und gebogen um eine genaue Anpassung an die Umgebung zu gewährleisten.
Alle Verschienungen werden auf Wunsch einschließlich Montagematerial, Isolierungen und Abdeckungen geliefert.Auch der Umbau bestehender Verschienungen oder der
Austausch einzelner Segmente ist in den meisten Fällen problemlos möglich.
In Kombination mit unseren Kontakten oder Modulbaugrup-pen erhalten Sie für den Weg vom Gleichrichter bis zum Behälter alles aus einer Hand, das verspricht maximale Kompatibilität.
48 49Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Modulbaugruppen
Gestelltechnik
Zubehör
Eine Modulbaugruppe beschreibt eine fertig vormontierte Wannenrandausstattung. Hierbei werden Kunststoffablagen, Aufnahmegabeln, Hochstromkontakte, Motorstromkontakte und Reinigungsvorrichtungen in der gewünschten Anord-
nung und Stückzahl auf Kunststoffhalter montiert. Die Baugruppen können dann als Ganzes geschraubt oder angeschweißt werden. Dies erspart eine mühevolle Ausrich-tung aller Einzelkomponenten.
Neben den klassischen Hochstromkontakten und Tromme-laggregaten haben wir auch klassische Bauteile der Gestell-technik im Angebot. Dieses reicht von Gestellklemmen mit Niederhalter „Lipfix“, über Anodenklemmen bis hin zu Gestellköpfen und Halteklötzen. Bei uns erhalten Sie alle benötigten Komponenten für Ihre Warenträger. Auch Sonderanfertigungen, Kleinserien und Einzelstücke finden Sie bei uns. Lassen Sie sich beraten.
AnodenkörbeBei uns erhalten Sie Anodenkörbe in verschiedenen Größen und Ausführungen. Die Form und Art der Befestigung wird kundenspezifisch ausgelegt. Auch die Anfertigung nach Handskizzen und Mustern stellt für uns kein Problem dar.
Unsere langlebigen Kontaktkabel werden standardmäßig aus PUR-Mantelleitung gefertigt. Die speziell für uns gefertigte Leitung ist in verschiedenen Durchmessern und Querschnit-ten erhältlich. Auch Sonderanwendungen wie PVC, Silikon und Neoprenleitungen sind möglich. Unsere „Kontaktbir-
nen“ gibt es wahlweise aus Stahl, Messing, Edelstahl oder Sonderwerkstoffen, wie Titan oder Kupfer. Die Ausführung kann hohl, schraubbar, durchgehend oder in weiteren Sonderformen erfolgen. Lassen Sie sich individuell beraten und erhöhen Sie die Lebensdauer dieses Verschleißartikels.
Kontaktkabel
50 51Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Hochstromkontakte DE
Plating Barrels & Aggregats
About us 54
Barrel aggregates 55
Barrel materials 58
Bearing systems 59
Contact systems 64
Contact Cable 66
Cover systems 68
Perforations 70
Filter plugs 72
Small barrel aggregates 74
Satellite plating aggregates 76
Rotating racks 78
Rotating contact systems 79
Pickling and phosphating barrels 80
Automatic cover opening and closingstation (DOS) 81
Electro-polishing barrel 82
Motor current contact 84
Plastic receptions 84
Tube barrel body 85
Gearwheels 86
Gesamtkatalog: Trommelaggregate und Galvaniktrommeln 4
Catalogue intégral en français : Tonneaux de galvanoplastie et groupes 102
High-Current Contacts
High-Current Contacts 87
Surface contacts 88
Surface contacts with pneumatic drive and water cooling 90
Easy refitting of existing contact system 92
Fingercontacts 93
Special designs and receptions 94
Cleaning devices 96
Connecting cables and conductor lines 98
Plastic receptions 98
Copper rail connections 99
Module components 100
Anode baskets 100
Cable contacts 101
Rack technology 101
Gesamtkatalog: Hochstromkontakte 37
Catalogue intégral en français : contacts courant fort 137
DE
EN
FR
Seite 52
Seite 102
Seite 4
DE
EN
FR
Seite 52
Seite 102
Seite 4
EN
52 53Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates High-Current Contacts
We are a medium-sized company based in Iserlohn (North Rhine-Westphalia). Long-lasting experience has made us experts for electroplating and high-current technology. Our team has profound experience in planning, developing and achieving customized solutions.
We take customer-specific advice serious in order to identify the suitable products together with you.
Competence, commitment and ideas create the solid platform of our company. Our products share a high quality standard and stand out because of extreme durability.
As a competent partner we offer you intelligent and customized solutions for all aspects of electroplating.
Customized solutions for the electroplating industry
Barrel aggregates andplating barrels
Ideas for electroplating and high current!
EN
54 Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Plating Barrels & Aggregates
• SEW gear wheel motors• protective varnish OS3• special designs, speed regulation and swing control system possible• brake optional
DriveBarrel aggregatesWe plan, construct and produce barrel aggregates appropriate to your system so that your machine can work without interruptions. Due to our perfect matching components we always provide the correct solution for your applications. Manufacturing as single or double-barrel aggregate or special construction.
Transport bars
Contact systems
Bearing
Barrel carrier
Protective cover
• transport bars for chain hoists or carriers• motor current contact system inside
the carrier if requested• standard blade contact• elastic motor current contacts • cleaning devices for clean contact systems • connecting rail for equipotential if requested• other bars possible• extensive range of standard types• for detailed information see chapter ‘High current technology’
• bearing as plastic sleeve bearing or liquid-tight metal sleeve bearing
• current transmission for electroplating by cable, disk, button, bar … (for further information see p. 66)
• torsion-free constructions made of steel or stainless steel• resistant to corrosion due to epoxy resin coating, pickled
and passivated or rubberized• individually designed carriers possible
• protection for motor and gear units made of PP• protection against process solutions and vapours
EN
56 57Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Plastic sleeve bearing with cable contact
• solid steel arm• contact disk firmly connected to the barrel• rotating bellows• special contact fluid inside the bellows• wear-free static seals
Bearing systems
• interchangeable bearing pivots and bearing bushes• flexible contact cables• contact bulb made of steel, stainless steel, brass …• bushings with drain holes
Liquid-tight metal sleeve bearing with disk contact
Contrasting volumetric wear values of different materials
Material density p in Kg/m3 wear
PE 1000 0,93 100
Steel St 37 7,85 160
PE 500 0,96 300
PP 0,92 600
PVC-hard 1,43 900
Bechwood 0,83 2.700
Barrel materialsDepending on the chemical and thermic stress parameters we use PP, PE 500 or ultra-high molecular polyethylene PE 1000 as barrel materials. It is also possible to produce barrels made of PPs and PVDF.
Barrel material PP grey
Barrel material PE 500 natural
Barrel material PE 1000 natural
• smooth, water-repellent surface• resistant to chemical attack• resistant to abrasion• impact-resistant• resisting temperatures of up to 80 °C• weldable
• smooth, water-repellent surface• resistant to chemical attack• good resistance to abrasion• particularly impact-resistant• resisting temperatures of up to 90 °C• weldable
• smooth, water-repellent surface• resistant to chemical attack• extremely resistant to abrasion• totally impact-resistant• resisting temperatures of up to 100 °C
EN
58 59Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Plastic sleeve bearingSingle components for the plastic sleeve bearing with intermediate wheel bearing and cogwheel
Pos. name material
1 flange (80 x 20 x 150 for plastic sleeve bearing) 1.4301
2 stud bolt (length on demand) C45
3 screw (m 12 x 25 – DIN 912) 1.4571
4 casing pipe (length on demand) PP
5 carrier pivot bar PE
6 carrier pivot PE
7 grooved dowel pin (d = 10 x 30 – DIN 1473) PVC
8 thrust ring PE
9 bushing PE
10 screw (m 16 x 40) PE
11 O-ring (10,77 x 2,62 – ARP 111) perbunan
12 idle wheel block (150 x 143,3 x 76) PP glass fibre reinforced natural
13 screw (m 12 – DIN 933) 1.4571
14 washer (13,0 – DIN 7349) 1.4571
15 seal screw PP
16 bearing bush PTFE
17 cogwheel (model and number of teeth on demand) PE 1000 natural
18 locking wheel PE 1000 natural
19 screw (m 8 x 30 – DIN 7991) 1.4571
12
13
14
15
1
4
3
2
5 8
6
17
11 10
9
7
16
19
18
EN
60 61Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Single components for the liquid-tight metal sleeve bearing with disk contact and intermediate wheel bearing and cogwheel
23
25
22
Liquid-tight metal sleeve bearing with disk contact
1
24
19
20
18
17
16
15 14
9
12
13
11
108
7
6
2
21
5
27
3 4
26
Pos. name material
1 support arm with flange 1.4301/st.
2 strip belt – LA1 Cu-Ag
3 compression spring 1.1200
4 contact pin Cu
5 bellow with right-hand thread PE 1000 natural
6 balancing flange PE 1000 natural
7 bearing bush Bz-Si
8 contact disk Bz
9 bearing flange St
10 seal ring para rubber
11 contact disk st37 nickel-plated
12 flange + O-ring 1.4571 + perbunan / viton
13 locking disk + O-ring PE 1.000 natural + perbunan / viton
14 screw (m 10 x 20 spec.) + O-ring 1.4571 + perbunan / viton
15 covering cap PP
16 screw (m 10 x 25 – DIN 933) 1.4571
17 O-ring (129,54 x 5,33) perbunan
18 sealing screw PP
19 screw (m 12 – DIN 933) + spring ring 1.4571/st.
20 washer (13 – DIN 7349) 1.4571
21 idle wheel bearing block (height on demand) PP glass fibre reinforced
22 cog wheel (model and number of teeth on demand) PE 1000 natural
23 locking wheel PE 1000 natural
24 screw (m 8 x 30 – DIN 7991) 1.4571
25 bearing bush PTFE
26 bolt 1.4301
27 safety pin PE 1000 natural
EN
62 63Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Contact systemsWe have developed various standard solutions to provide you with the optimal contact system for your range of products.
Cable contact (dangler) with plastic sleeve bearingCable contacts are the most cost-efficient and widespread contact systems. They are particularly suitable for compact bulk goods. Thus they cover a broad range of application. They are also available with hollow bulb or in special designs.
Disk contact with metal sleeve bearingDisk contacts are excellently suitable for high current transmissions. They can be used for bulky, compact and sharp- edged goods as well as sensitive goods which could be damaged by static contacts.
Cable contact (dangler) with plastic sleeve bearing and continuous bulbCable contacts with continuous bulbs have a larger surface for a better contacting of the goods. Due to the loose-han-ging contact bulb the goods are not hit. Therefore, this cable system is especially interesting for sensitive goods.
It can be easily installed and maintenance costs are low. It can also be obtained with a screwed contact bulb for a quick replacement and with a hollow bulb for extremely sensitive goods. A cost-effective alternative to a rod contact system.
Rod contact with metal sleeve bearing Rod contacts are inserted into the edge bars of the barrel and transfer the current from the liquid-tight metal sleeve bearing via contact disks evenly along the total inner length of the barrel. The interior space of the barrel remains smooth. Rod contacts are suitable for electroplating a wide range of goods. This type of contact system is especially suitable for rod-shaped parts.
Universal contact with metal sleeve bearingUniversal contacts offer the possibility to apply numerous different types of contacts and change them quickly if requi-red. Customized special designs can be easily realised.
Button contact with metal sleeve bearingSimilar to rod contacts, button contacts offer an even current transmission along the total inner length of the barrel. They are especially suitable for sensitive goods which could be damaged by static contacts. Moreover, even if the barrel is only filled minimally, they guarantee a perfect current trans-mission. Button contacts can be easily replaced.
EN
64 65Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Our long-lasting contact cables are made of PUR sheating as standard. This sheating especially made for us is available in different diameters and cross sections. It is also possible to produce them of PVC, silicone and neoprene.
Our contact heads are available made of steel, brass, stainless steel or special materials like titan or copper. They can be designed in various versions: hollow, screwable, continuous or further designs. Ask for personal advice to enhance the durability of this item subject to wear.
Contact Cable
You will find an application form for cable contacts on the internet at: www.linnhoff-partner.com/en-downloads
Cable lug / connection• tubular cable lug in narrow design to enable an easy cable
insertion through the bushing or carrier trunnion• all standard drillings
SealingThere are 2 kinds of sealings available:• The cable is protected against spray and dust by a rubber grommet.• The cable can be liquid-tightly sealed by a sealing sleeve made of stainless steel.
CableThe resistant PUR sheating is extremely durable. It is available in various combinations of diameter and cross sections as follows:• Ø14: 35mm²• Ø20: 50mm²; 95mm²• Ø25: 95mm²• Ø28: 120mm²• Ø29: 150mm²• Ø30: 120mm²; 185mm²• Ø32: 240mm²
Contact head• Contact heads are available made of steel, inox or
brass as standard.• Due to the eightfold pressing at a pressure of several
tons a very tight connection to the sheating is obtained. • To enable a quick changing the contact bulb can also
be produced in a screwable version.
EN
66 67Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
All cover systems can be opened and closed manually or automatically.
Cover systems
Cover system with L-shaped cover grooveA simple design of a tightly closing system. This cover system is often used for older installations. It is suitable for most ranges of products.
Cover system with VK-shaped cover grooveAt present this is the most widely installed system. Even abrasive and pointed parts will not enter the groove.
Cover system with V-shaped cover grooveThis system has similar qualities as the VK-shaped model, but it is only suitable for delicate, non-abrasive components.
EN
68 69Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
The quality and effectiveness of barrel electroplating is considerably depending on the kind and size of the perforation.We offer a wide range of different perforations in order to choose the perfect one for your applications.
Round perforation The outstanding quality of the barrel material allows an extremely close perforation. Inner and outer counterbores resp. milled recesses support the electrolytic exchange, reduce the drop in voltage in the wall, reduce carry-over losses and prevent flat components from adhering to the wet barrel.
Special features:• very close hole distance• counterbores on both sides• as for sticky components overlapping counterbores can be milled
Slot perforationDue to the overlapping milling of the slots the stability of the individual plates remains intact. The outstanding quality of the barrel material allows the very close perforation, therefore even higher component weights do not present a problem.
Half-moon perforationAmong all kinds of perforation the half-moon perforation offers the widest range of products (nails, screws, coins, punched and bent components, and many more). A considerably larger perforation space of up to more than 30 per cent (e.g. in contrast to an equivalent round perforati-on) guarantees a better electrolytic exchange. By means of special milling tools plates of up to 20 mm can be easily perforated in the half-moon version, thus resulting in con-siderably longer service lives. The conical form on the outsi-de enables both a quick penetration and a quick draining of the electrolyte.
Long-slot perforationSimilar to the design of the half-moon perforation, the long-slot perforation offers the same advantages. It has been developed to replace the sawn slot perforation as the dimen-sionally stable geometry avoids a widening of the perforation.
Perforations
EN
70 71Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
For a number of years now, our filter plugs have shown their worth – not only in the area of barrel technology. Meanwhile, our filter plugs are also used in filter systems and sieve plates. In the wide range of perforations and designs, the suitable filter plug for your application will also be found.
Our perforation system of filter plugs offers these decisive advantages:
• simple replacement of filter plugs* for an optimal adaptation to the goods• due to the arched form of the filter plug the adherence of flat components will be avoided• the filter plug material reduces voltage drops and carry-over losses• big chamfers facing outwards provide an excellent exchange of the electrolyte because of the additional pumping effect.
* The filter plugs cannot be reused afterwards.
A-filter plug product range approx. 40 mm / material: PP
E-filter plug product range approx. 23 mm / material: PP
standard model
concave model
convex model
Filter plugs
Pos. name artikel number
1 0,25 slot 90000100
2 0,4 slot 90064500
3 0,6 slot 90117800
4 1,3 slot 90018400
5 1,3 slot concave 90081800
6 1 x 1 90000400
7 1,75 x 1,75 90070300
8 2 x 2 90000500
9 2 x 2, convex 90000700
10 2 x 2, concave 90037950
11 3 x 3 90000800
12 3 x 3 convex 90000900
13 8 x 8 convex 90018300
14 0,25 slot with 2 x 2 raster 90000300
15 15 half-moon plug 1,3 mm 90823700
Pos. name artikel number
1 0,25 slot 90001300
2 0,4 slot 90019500
3 0,4 x 0,4 90117600
4 1 x 1 90017100
5 1 x 1 convex 90001400
6 2 x 2 90098900
EN
72 73Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Developed for rational plating of small series or small parts, our small barrel series is frequently used for many different applications. Easy handling and the low weight of this series allow for batch weights of up to 13 kg. When a chain hoist is used, the weight per batch increases to up to 30 kg.
For the standard type, the barrel body is made of polypropy-lene; however, special designs in other materials are possible. For example, best results in chemical nickel applications have been achieved with PVDF barrels.
To reduce carry-over losses to a mini-mum, the entire barrel body is welded and the seams are smoothed. This prevents the product from getting caught in the barrel. A special groove structure at the fronts avoids that flat products stick to the surface. Owing to the largely dimensioned cover opening, easy product feed and removal is possible.
The attached cover provides optimal operational safety and easy handling. Position and shape of the cover are
designed in such a way that not even the smallest particles can get between cover and barrel body.
To transfer the plating current onto the product, different ways of contacting can be selected. One example is the classic cable contact, but also disk contacts, button cont-acts, pin contacts and many others are possible.
There is also the possibility of network-independent battery operation with a docking station and equipment with a
pendular unit, reverser unit or vibrating unit. To improve electrolytic exchange, an additional electrolyte injection pump can be added.
In short, the small barrel series is the optimal partner for rational plating. For electronic components, in the jewellery industry, for small series, subcontracted electroplating, research and development, the small barrel is a must.
Small barrel aggregates
EN
74 75Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Transport bars
Contact system
Bearing
Barrel carriers
Protective cover
Collector baskets with contact system
Adjustable end walls
Collector basket opening
• transport bars for chain hoists or carriers• motor current contact system in the carrier - optional
• standard blade contacts• spring-loaded motor current contacts• cleaning device for clean contact systems• connecting rail for equipotential – optional• further bars available on demand• vast programme of standard designs
• liquid-tight plastic sleeve bearing
• torsion-free construction made of steel or stainless steel• resistant to corrosion due to epoxy resin coating,
pickled and passivated or rubberized• individual carrier designs possible
• protection for motor and gear units made of PP
• protection against process solvents and vapors
• The contact system is equipped with pin contacts which are set in midst the collector baskets. These contact pins can be designed one-sidedly, two-sidedly or continuously. Each one can individually exchanged.
• The openings of the collector baskets can be designed in different shapes according to the goods, f.ex. in a hexagonal or rectangular form. As standard they are designed in a round shape.
• By removable and adjustable intermediate walls the barrel can be divided into several usable segments. The adjust-ment of the intermediate walls is effected by a pressing stick resulting into a positive insert locking.
• The largely dimensioned collector basket opening (opening angle 135°) makes it easy to fill the collector baskets.
• SEW gear wheel motor• protection varnish OS3• special designs• speed control regulation and
swing control system• brake – optional
Barrel drive
Especially designed for bar-shaped flat or round material, these aggregates can be modified into single or double-barrel aggregates. The barrel can be divided into several usable segments by installing removable intermediate walls. These aggregates are designed for batch weights of up to 300 kg and lengths of up to 2500 mm.
Satellite plating aggregates
EN
76 77Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Rotating racks current-carrying and currentlessRotating contact systems
Our rotating racks are the perfect solution for components with unfavourable shapes like blind holes, undercuts or pockets in which air bubbles can arise. The goods are
separately treated in special devices or alternatively adapted in baskets to the rack. Therefore an equal treating is possible and damages are minimized.
Current-carrying rotating contact systems are another range of application which were designed for the treating of one or two parts maximum. These rotating contact systems are mainly used in the field of galvanoforming or hard chrome
processes, f.ex. when embossing rolls or piston rods are electroplated. Piece weights of several hundred kilograms are not uncommon here.
EN
78 79Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
These aggregates are manufactured according to customers’ requests. The perforation can be chosen individually. Barrel carriers and protective covers are manufactured according to
our standard programme. The barrel carriers and bearing bars are made of stainless steel. You can choose between 1.4301, 1.4401 or 1.4571.
Automatic cover opening andclosingstation (DOS) Cover-opening processThe cover-opening device automatically brings the electroplating barrel into the loading and unloading position, preposi-tions itself and is then fine-positioned. As soon as this positioning is completed the actual cover-opening process begins.
Due to the extension of the lifting cylinder the cover-opening tools are tilted and grip into the recesses of the cover toggles. The design of the gripping tools guarantees a smooth gripping of the toggles and a reliable holding of the cover in the cover-opening device.
As the cover-opening tools are connected by a flat bar, an identical angle of inclination of each individual tool is guaranteed at any time.
After the cover has been lifted by the opening device, the device returns to the initial position together with the cover. The barrel can now be loaded resp. unloaded without hindrance.
Due to the simple design of this loading and unloading station the number of movements is reduced to a minimum. This results in a number of crucial advantages regarding cost-effectiveness, reliability and service life.
Cover-closing processThe cover is closed in the same way as it is opened but in reverse order. The device always returns the cover reliably and precisely to the barrel opening.
Pickling and phosphating barrels made of stainless steel
EN
80 81Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
When designing this innovative conception of an electro-polishing barrel we paid particular attention to the quality of the finished goods. Due to the electro-polishing barrel it has been possible for the first time to electropolish goods of a maximum volume of 8 litres resp. of a maximum weight of 25 kg with consistent premium quality.
The advantages of this barrel at a glance• careful processing using high-quality materials guaran-
tees a long operating life even under extreme conditions.• solid system construction suitable for the intended
application • a precise and tightly closing cover• user-friendly operability and operation safety meeting even the highest demands due to the cover closing system• stable bearings• optimal electrolyte exchange and minimized carry-over loss by means of smooth, water- repellent material surfaces and gap-free transfers combined with a sophisticated perforation system
In case of a barrel filling volume of 80 % (apprx. 8 litres), the supplied current amounts to apprx. 500 – 600 A at a voltage of 6 – 10 V. The cycle for electro-polishing lasts between 5 and 15 minutes – depending on the condition of the starting material. Due to the additionally developedcontrol electronics a continuous speed setting as well as an oscillating operation are possible.
The liquid-tight metal sleeve bearings directly transfer the current onto the barrel body made of titanium or stainless steel. The special contact fluid in the inner part of the earing keeps the contact surfaces clean. This system allows current transmissions of up to 500 A per side.
The double-walled barrel body and the double-walled central pipe are absolutely short-circuit resistant. One wall transfers the anode current, the other one transfers the cathode current.
DriveWe use high-quality gear wheel motors with circuit breakers for the drive. The motor voltage amounts to 12 V or 24 V direct current. Moreover, the barrel speed can be continuously adjusted at the aggregate.
Contact supportFor galvanic current transfer we usually use blade contacts made of copper which are also suitable for high currents.
Barrel bodyThe barrel body is made of titanium and stainless steel 1.4571. The liquid-tight sleeve metal bearing enables a current transmission of up to 500 A. The special form of the cover guarantees a gap-free fitting. The cover can be opened and closed easily by means of the handy rotary toggle.
Transport barThe transport bar for the electro-polishing barrel has a shackle. On request we can also deliver other types of transport bars. An adaptation of the bars or of the complete carrier is possible in most cases.
Electro-polishing barrel
EN
82 83Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
The motor current contact is an important element of a properly functioning barrel aggregate. Our motor current contacts have decisive advantages and ensure a trouble-free operation of your plant.
Advantages:• self-cleaning contact surfaces• very high current transmission (up to 60 A)• extremely robust and therefore very reliable• construction convenient for maintenance and repair
Plastic receptions are mainly manufactured from PE or PP. You can choose between our low-priced standard receptions or a version designed to your requirements.
Because of our 5-axis CNC centres we are also capable to manufacture complex shapes. A sample or sketch will do in most cases.
This ‘barrel within a barrel’ can be used for galvanising small batches by simply placing the tube barrel body inside the existing barrel. The body is made of PP grey and is equipped with screws with stainless steel cap nuts as contacts. There are two sizes available with internal diameters of 50 mm and 100 mm. The length can be specified by you.
Regarding the barrel body with an internal diameter of 100 mm, the contacts are also fitted at the front side. The standard perforation is round with a diameter of 6 mm. Special perforations and special forms are available on request.
Motor current contact
Plastic receptions
Tube barrel body
EN
84 85Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Plating Barrels & Aggregates
Our gearwheels are completely manufactured by us, be it single pieces or small batch series. Our range varies from driving gearwheels for small barrel aggregates to groups of gearwheel series consisting of several parts.
They are mainly made from PE 1000, but it is also possible to manufacture them of PE 500, PP, PPs, stainless steel or many other materials. They can also be made combining plastic and metal.
Gearwheels High current contacts & cleaning devices
86
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high current!
Our surface contacts impress by their simple construction. Due to a solid welded construction made of high-quality stainless steel, they have a durable and trouble-free working life. The contact plates are pressed by insulated springs to the contact surfaces under high pressure
enabling an ideal current transmission. Connection is effected by means of simple connection cables directly onto the contact plates. Therefore no extra conductor lines are necessary when the goods are moved. They are solid, easy to maintain, cost-efficient and self-cleaning.
Surface contacts
Compression springs• insulated compression springs made
of stainless steel for constant pressure• anti-corrosion coating - optionalMonitoring
• monitoring of contacts by tempe-rature sensors PT100 – optional
Protective covers• protective covers made of
1.4301 to shield off falling dirt
Solid stainless steel construction• support console made of 1.4301 with solid guide
rails in form of a welded construction• optionally made of 1.4571, coated or with additional
guide rails made of PE
Connections• straight or angled to connect
conductor lines easily
Replaceable contact plate• easily replaceable contact plates with wiper
grooves for self-cleaning when running in
88 89
1500 A 3000 A
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Pneumatic design Pneumatic contacts are only applied when high currents, little space or low input weights present a challenge. The contact pressure is reached by using vulcanized pressure bags. There are hardly any limits regarding pneumatic surface contacts. You will often find them with an output of 20 kA and more. Due to an additional instalment of a water cooling the power output can be increased at any time. The costs are relatively high, however, you gain a maximum process reliability.
Water-cooled design If you want to increase the power output of the surface contact, we can recommend the water-cooled design as it does not need more space. By using a water-cooled surface contact the maximum power output can be increased by up to 35 % depending on the cooling capacitiy. The water cooling is installed inside the connection plates. We also recommend installing PT 100 temperature sensors to monitor the contacts ideally. So a safe operation of the contacts is always guaranteed.
Pneumatic pressure bags• pneumatic drive using
vulcanized pneumatic pressure bags
Compression springs• insulated compression springs made
of stainless steel for constant pressure• anti-corrosion coating - optional
Insulation plate• insulation plate made of PPs or
HGW to protect the pneumatic pres-sure bag against heat exposure
Water cooling• water cooling to increase
capacity - optional
Contact plates• easily replaceable contact plates
with wiper grooves for self-cleaning when running in
Protective covers• protective covers made of
1.4301 to shield off falling dirt
Connections• straight or angled to
connect conductor lines easily
Support console• support console made of 1.4301 with solid
guide rails in form of a welded construction• optionally made of 1.4571, coated or with
additional guide rails made of PE
Monitoring• monitoring of contacts by
temperature sensors PT100 – optional
Surface contacts with pneumatic drive and water cooling
90 91
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Each contact system can be individually adjusted to any installation. All our systems are tested in practice. Depen-ding on the version a power multiplication is possible.
Easy refitting of existing contact system
prism reception
contact sword reception
round-pivot reception
V-shaped reception
Finger contacts with several spring-loaded single fingers enable a good contact even when the contact surface at the carrier is not smooth. Ideally the contact fingers are
equipped with wiper grooves to clean off loose dirt when the carrier enters. To tie the movable elements to the basic body foil tapes are used.
Using a pressure bag for the pneumatic finger contacts it is possible to increase the contact pressure in order to reach a better contact. Especially in existing installations the contact
surface of the carrier is often uneven. In this case it is advisable to opt for contacts with pneumatic fingers.
Finger contacts
Pneumatic finger contacts
92 93
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Special designs and receptions
Bolt contactsAt the early stages of automation technology, bolt contacts were often used in electroplating plants. Today, they are still used for contacting extendable anodes and in electrolytic cells. The base body is made of brass and can be mounted directly onto the connecting rail. So unnecessary connec-tions are no longer required.
Inside the contact there are spring-loaded bolts linked to contact strips. The power output of the maximum current depends on the number of contact bolts. Each bolt is capable of transferring apprx. 400 A. In most cases, however, we recommend to apply a cost-efficient high current surface contact.
Brass receptions have been in use for more than 100 years. In the early years of electroplating only bent spring contacts were used next to brass receptions. In case of lower currents of up to 500 A these contacts are still sufficient today.
Low costs and good mechanical qualities are advantageous. Unfortunately, they are not self-cleaning and are therefore subject to constant care.
We do not produce our contacts only for the electroplating industry. Special designs are also applied in maintenance facilities for trains, quick-change systems for pressing tools, vacuum furnaces, test facilities, recycling plants and special plants for astronautics.
Wherever high currents have to be transferred safely, our special contact systems are the fitting solution. In this respect each project will be intensively planned together with you until a useful and working solution has been found.
Sliding contacts are often applied in the conductor board electroplating industry because you will only find low insert weights there. Using sliding contacts requires a high accuracy when inserting and a precise position of the
contacts. Due to their limited compensating possibilities, they are not suitable for vats with 3 or 4 contact areas. Sliding contacts as well as brass receptions do not have a ‘self-cleaning effect’.
Special contact systems
Sliding contacts
Brass receptions
94 95
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Although there was already talk about this 90 years ago, it is still being neglected many times today. Only clean contacts can work efficiently.
To support your staff, we recommend cleaning devices at the rinsing tanks. These cleaning devices work independently of the plant operator. The contact surfaces of the carrier are cleaned during each cycle.
The simple and solid construction pays off here, too. The brushes can be changed individually. Cleaning devices can be optained for each type of contact (sword, pivot, prism, etc.) In most cases the cleaning devices can easily be changed for the existing plastic receptions.
Cleaning devices
‘Beginners often overlook to keep the wires and contacts clean. But this is of vital importance for the power circuit and thus for the plating process.’
Dr. W. Pfanhauser, Galvanotechnik, 1928
Solid inox construction • made of 1.4301• hole pattern of the fixing holes according
to your demands
Individually changeable strip brushes• The strip brushes can directly be changed at the tank,
it is not necessary to remove the cleaning device.
Spring-loaded holdingblocks made of PE 1000• for mounting the strip brushes• to receive the strip brushes the holding blocks
can be adjusted via the inner hexagon screws
96 97
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
We recommend using highly flexible connecting cables when connecting high current contacts or rectifiers. We produce these in different designs and cross sections according to your demands. These cables can be produced either of crimped copper braids and connecting flange or cable lug. According to your range of application and operation site the connecting cables are equipped with protective hoses of various materials like PVC, silicone or PUR before they are tightly crimped. We gladly advise you which cable suits your needs best.
Connecting cables and conductor lines
Plastic receptions
Copper rail connectionsAccessories
Our plastic receptions are mainly manufactured from PE or PP. You can choose between our low-priced standard receptions or a version designed to your requirements.Because of our 5-axis CNC centres we are also capable to manufacture complex shapes. A sample or sketch will do in most cases.
Making use of modern and professional piercing and bending technology we are able to produce and install copper rail connections on your premises. The raw material will be cut, pierced and bent on-spot to guarantee a precise adjustment to the operation site.
On request all copper rail connections will be delivered including assembly material, insulation and coverings.
Normally it is also possible to modify existing connections or exchange individual segments without problems.
Together with our contacts or module components you will receive everything for the way from the rectifier to the reception from one provider. Thus a maximum compatibility can be expected.
98 99
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Module components
Accessories
Module components consist of ready pre-assembled tank rim equipment. This means that (plastic) receptions, high current contacts, motor current contacts and cleaning devices are assembled onto plastic plates according to your
requirements. These module components can be fastened with screws or welded as a unit. So a troublesome arrange-ment of all single components is avoided.
Anode basketsWe deliver anode baskets in various sizes and designs. Their shape and way of fixing will be made according to your needs. We can also design them easily according to freehand sketches and samples.
Our long-lasting contact cables are made of PUR sheating as standard. This sheating especially made for us is availablein different diameters and cross sections. It is also possible to produce them of PVC, silicone and neoprene. Our contact heads are available made of steel, brass, stainless steel or
special materials like titan or copper. They can be designed in various versions: hollow, screwable, continuous or further designs. Ask for personal advice to enhance the durability of this item subject to wear.
Cable contacts
Rack technologyNext to the classic high current contacts and barrel aggrega-tes we also offer conventional components of rack technolo-gy. They comprise rack clips with pressure frame ‘Lipfix’, anode clips, rack fastener and holding blocks. We provide you with all necessary components for your carriers. You will also find special designs, small series and single units in our programme. Contact us and allow us to advise you.
100 101
ENHigh-Current Contacts
Personal advice and orders: phone +49 23 71 / 15 75-0 or e-mail: [email protected]
Ideas for electroplating and high-current!
Tonneaux de galvanoplastie & groupes
A propos de nous 104
Tonneaux complets 106
Matériaux des tonneaux 108
Systèmes de palier 109
Systèmes de contact 114
Câbles de contact 116
Systèmes de porte 118
Perforations 120
Pastilles 122
Groupes de petits tonneaux 124
Groupes de tonneaux « satellite » 126
Châssis rotatifs 128
Contact rotatifs 129
Tonneaux pour le décapage et le phosphatage en acier inoxydable 130
Dispositif d’ouverture et de fermeture automatique du porte 131
Tonneau de polissage électrolytique 132
Contact courant moteur 134
Supports de cuve 134
Mini tonneau 135
Engrenages 36
Gesamtkatalog: Trommelaggregate und Galvaniktrommeln 4
English complete catalogue: Barrel aggregates and plating barrels 52
Contacts pour courant fort
Contacts pour courant fort 137
Contacts de surface 138
Contacts de surface avec entraînement
pneumatique et refroidissement par eau 140
Modification simple des contacts disponibles 142
Contacts à doigts 143
Formes spéciales et logements 144
Dispositifs de nettoyage 146
Câbles d’alimentation et tresses 148
Logements en plastique 148
Rails en cuivre 149
Groupes modulaires 150
Paniers anodiques 150
Câbles de contact 151
Châssis 151
Gesamtkatalog: Hochstromkontakte 37
English complete catalogue: High-Current Contacts 87
102 103Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
DE
EN
FR
Seite 52
Seite 102
Seite 4
DE
EN
FR
Seite 52
Seite 102
Seite 4
Contacts pour courant fort
Nous sommes une entreprise de taille moyenne basée à Iserlohn dans la Rhénanie du Nord-Westphalie en Allemagne. Forts d’une longue expérience, nous sommes des experts de la galvanoplastie et de la technologie de courant fort. Notre équipe bénéficie d’une expérience approfondie dans la planification, le développement et l’élaboration de solutions personnalisées.
Nous prenons très au sérieux les besoins spécifiques de chaque client afin d’identifier ensemble les produits les plus adaptés.
Compétences, engagement et idées : voici le solide socle de notre entreprise. Nos produits partagent un niveau de qualité élevé et se démarquent par leur extrême durabilité.
Partenaires compétents, nous vous offrons des solutions intelligentes et personnalisées adaptées à tous les aspects de la galvanoplastie.
Solutions personnalisées pour l’industrie galvanoplastique
Groupes de tonneaux et tonneaux de galvanoplastie
Des idées pour la galvanoplastie et le courant fort !
104Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Tonneaux de galvanoplastie & groupes FR
Nous planifions, construisons et produisons des systèmes de tonneaux adaptés à votre système pour garantir que votre machine puisse fonctionner sans interruption. Grâce à nos composants en parfaite adéquation, nous fournissons toujours la solution adaptée à vos applications.
Fabrication possible de systèmes à simple ou double tonneau ou de constructions spéciales.
Tonneaux complets
Barres de transport
Porteur de tonneau
Porte de protection
• barres de transport pour palans à chaîne ou chariot• système de contact courant moteur dans
le chariot sur demande
• constructions en acier ou acier inoxydable sans torsion• résistant à la corrosion grâce au revêtement en résine époxy,
décapé et passivé ou caoutchouté• possibilité de commander des porteurs individuellement adaptés
• protection pour les unités motrices ou à engrenages en PP• protection contre les produits et les vapeurs du processus
Systèmes de contact
Palier
• contact à lame standard• contacts courant moteur élastiques • dispositifs de nettoyage pour nettoyer les
systèmes de contact • barre de connexion pour liaison équipotentielle
sur demande• autres barres disponibles• vaste gamme de types standard• Pour des informations détaillées, voir
chapitre « Technologie de courant fort »
• palier à coussinet en plastique ou palier à coussinet en métal étanche
• transmission de courant pour galvanoplastie par câble, disque, plot, barre, etc. ( pour plus d’informations, voir p. 114 )
• moteurs réducteurs SEW• vernis protecteur OS3• possibilité de conceptions spéciales,
système de régulation de la vitesse et de contrôle du balancement
• frein en option
Transmission
106 107Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Palier à coussinet en plastique avec contact à câble
• bras en acier solide• disque de contact solidement relié au tonneau• soufflets tournants• fluide de contact spécial dans les soufflets• joints statiques sans usure
Systèmes de palier
• pivots et douilles de palier interchangeables• câbles de contact flexibles• bulbe de contact en acier, acier inoxydable, laiton, etc.• bagues avec trous de drainage
Palier à coussinet en métal étanche avec contact à disque
Valeurs d’usure volumétriques pour différents matériaux
Matériau densité p en kg/m3 usure
PE 1000 0,93 100
Acier st37 7,85 160
PE 500 0,96 300
PP 0,92 600
PVC / solide 1,43 900
Bois de hêtre 0,83 2.700
Matériaux des tonneauxEn fonction des paramètres de contraintes chimiques et thermiques, nous utilisons du PP, du PE 500 ou du polyéthylène de poids moléculaire ultra-élevé PE 1000 pour fabriquer nos tonneaux. Il est également possible de produire des tonneaux en PPs et PVDF.
Matériau pour tonneaux PP gris
Matériau pour tonneaux PE 500 naturel
Matériau pour tonneaux PE 1000 naturel
• surface lisse, hydrofuge• résistant aux attaques chimiques• résistant à l’abrasion• résistant aux chocs• résistant aux températures jusqu’à 80°C• soudable
• surface lisse, hydrofuge• résistant aux attaques chimiques• bonne résistance à l’abrasion• particulièrement résistant aux chocs• résistant aux températures jusqu’à 90°C• soudable
• surface lisse, hydrofuge• résistant aux attaques chimiques• extrêmement résistant à l’abrasion• complètement résistant aux chocs• résistant aux températures jusqu’à 100°C
108 109Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
12
13
14
15
1
4
3
2
5 8
6
17
11 10
9
7
16
19
18
Systèmes de palierComposants individuels pour le palier à coussinet en plastique avec roulement de roue et roue dentée intermédiaires
Pos. Nom Matériau
1 bride (80 x 20 x 150 pour palier à coussinet en plastique) 1.4301
2 goujon (longueur sur demande) C45
3 vis (m 12 x 25 – DIN 912) 1.4571
4 tubage (longueur sur demande) PP
5 barre pivotante du porteur PE
6 pivot du porteur PE
7 goupille rainurée (d = 10 x 30 – DIN 1473) PVC
8 bague de roulement PE
9 bague PE
10 vis (m 16 x 40) PE
11 joint torique (10,77 x 2,62 – ARP 111) perbunan
12 palier de roue inactive naturel (150 x 143,3 x 76) PP renforcé de fibre de verre
13 vis (m 12 – DIN 933) 1.4571
14 rondelle (13,0 – DIN 7349) 1.4571
15 vis d’étanchéité PP
16 douille de palier PTFE
17 roue dentée (modèle et nombre de dents sur demande) PE 1000 naturel
18 18 roue de verrouillage PE 1000 naturel
19 vis (m 8 x 30 – DIN 7991) 1.4571
110 111Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Composants individuels pour le palier à coussinet en métal étanche avec contact à disque et roulement de roue et roue dentée intermédiaires
23
25
22
Systèmes de palier
1
24
19
20
18
17
16
15 14
9
12
13
11
108
7
6
2
21
5
27
3 4
26
Pos. Nom Matériau
1 bras de support avec bride 1.4301/st.
2 courroie ruban – LA1 Cu-Ag
3 ressort de pression 1.1200
4 broche de contact Cu
5 soufflet avec filetage à droite PE 1000 naturel
6 bride d’équilibrage PE 1000 naturel
7 douille de palier Bz-Si
8 disque de contact Bz
9 bride de palier St
10 joint d’étanchéité caoutchouc para
11 disque de contact st37 plaqué nickel
12 bride + joint torique 1.4571 + perbunan / viton
13 disque de verrouillage + joint torique PE 1000 natur + perbunan / viton
14 vis (m 10 x 20 spec.) + joint torique 1.4571 + perbunan / viton
15 capuchon de couverture PP
16 vid (m 10 x 25 – DIN 933) 1.4571
17 joint-torique (129,54 x 5,33) Perbunan
18 vis d’étanchéité PP
19 vis (m 12 – DIN 933) + circlip 1.4571/St
20 rondelle (13 – DIN 7349) 1.4571
21 palier de roue inactive (hauteur PP renforcé de fibre de verre sur demande) PP Gv
22 roue dentée (modèle et nombre de dents sur demande) PE 1000 naturel
23 roue de verrouillage PE 1000 naturel
24 vis (m 8 x 30 – DIN 7991) 1.4571
25 douille de palier PTFE
26 boulon 1.4301
27 goupille de sécurité PE 1000 naturel
112 113Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Systèmes de contactNous avons conçu diverses solutions standard pour vous fournir le système de contact optimal selon votre gamme de produits.
Contact à câble avec palier à coussinet en plastiqueLes contacts à câble sont les systèmes de contact les plus efficaces et les plus répandus. Ils sont particulièrement adaptés aux produits en vrac compacts. Ils couvrent donc un large spectre d’applications. Ils sont également dispo-nibles avec bulbe creux ou en conceptions spéciales.
Contact à disque avec palier à coussinet en métalLes contacts à disque sont parfaitement adaptés aux transmissions à fort courant. Ils peuvent être utilisés pour des produits en vrac, compacts ou anguleux, ainsi que des produits délicats qui peuvent être endommagés par des contacts statiques.
Contact à câble avec palier à coussinet en plastique et bulbe continuLes contacts à câble avec bulbe continu possèdent une surface plus grande pour un meilleur contact avec les produits. Les biens ne subissent pas de choc grâce au bulbe de contact libre. C’est pourquoi ce système de câble est particulièrement intéressant pour les produits délicats.
Il peut être facilement installé et les coûts de maintenance sont bas. Il est également disponible avec un bulbe de contact vissé pour un remplacement rapide et avec un bulbe creux pour les produits extrêmement délicats. Il s’agit d’une alternative rentable au système de contact à tige.
Contact à tige avec palier à coussinet en métal Les contacts à tige sont insérés dans les rebords du tonneau et transfèrent uniformément le courant du palier à coussinet en métal étanche via les disques de contact sur l’ensemble de la longueur intérieure du tonneau. L’espace à l’intérieur du tonneau reste lisse. Les contacts à tige sont adaptés à la galvanoplastie d’une large gamme de produits. Ce type de système de contact est particulièrement approprié aux pièces en forme de tige.
Contact universel avec palier à coussinet en métalLes contacts universels offrent la possibilité d’utiliser de nombreux types de contacts différents et de les changer rapidement si nécessaire. Des conceptions spéciales personnalisées peuvent facilement être réalisées.
Contact à plot avec palier à coussinet en métalSimilaires aux contacts à tige, les contacts à plots offrent une transmission du courant encore meilleure sur l’ensemb-le de la longueur intérieure du tonneau. Ils sont particulière-ment adaptés aux produits délicats qui peuvent être endom-magés par des contacts statiques. En outre, ils garantissent une transmission du courant parfaite même si le tonneau est rempli au minimum. Les contacts à plot peuvent être facilement remplacés.
114 115Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Il s’agit de câbles d’installation résistants avec une gaine PUR en série. Spécialement fabriqués pour nous, ils sont dispo-nibles en plusieurs diamètres et sections. Plusieurs applications spéciales (câbles en PVC, silicone et néoprène) sont disponibles sur demande.
Nos bulbes de contact sont disponibles en acier, en laiton, en inox ou autres matériaux spéciaux, tels que le titane ou le cuivre. Outre les formes creuses, filetées, continues, nous proposons également d’autres formes spéciales. N’hésitez pas à nous contacter pour une longévité accrue de cette pièce d’usure.
Câbles de contact
Cosse / Branchement• cosse tubulaire fermée à plage étroite pour une insertion aisée
du câble à travers les pivot et douille du palier• tous les perçages courants
ÉtanchéitéDeux finitions disponibles :• le câble est protégé de la poussière et des éclaboussures par un presse-étoupe en caoutchouc• un passe-câble en inox permet de fermer hermétiquement le câble.
CâbleLe câble d’installation résistant avec une gaine PUR se distingue par une longévité élevée. Les sections et diamètres suivants sont disponibles :• Ø14: 35mm²• Ø20: 50mm²; 95mm²• Ø25: 95mm²• Ø28: 120mm²• Ø29: 150mm²• Ø30: 120mm²; 185mm²• Ø32: 240mm²
Bulbe de contact• acier, inox ou laiton disponible en série • la pression octuple équivalente à plusieurs tonnes
permet d’obtenir un assemblage étanche avec la gaine• au choix, il est également possible d’installer un bulbe
de contact fileté pour le remplacer rapidement
Vous pouvez télécharger un formulaire de requête « Câble de contact » sur le site www.linnhoff-partner.com/fr-downloads
116 117Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Tous les systèmes de porte peuvent être ouverts et fermés manuellement ou automatiquement.
Systèmes de porte
Système de porte avec rainure du porte en forme de L Une conception simple pour un système qui ferme de façon étanche. Ce système de porte est souvent utilisé pour les installations anciennes. Il est adapté à la plupart des gammes de produits.
Système de porte avec rainure du porte en forme de VKActuellement, il s’agit du système le plus répandu. Même les pièces abrasives et pointues n’entre-ront pas dans la rainure.
Système de porte avec rainure du porte en forme de VCe système possède des qualités semblables au modèle en forme de VK, mais il n’est approprié que pour les composants délicats, non abrasifs.
118 119Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
PerforationsLa qualité et l’efficacité de la galvanoplastie en tonneaux dépendent largement du type et de la taille des perforations. Nous offrons une large gamme de perforations variées afin de choisir celle parfaitement adaptée à vos applications.
Perforation ronde La qualité exceptionnelle du matériau des tonneaux permet une perforation très proche. Des lamages internes et externes (des renfoncements fraisés) favorisent l’échange électrolytique, réduisent la chute de tension dans la paroi, réduisent les pertes de fonctionnement et empêchent les composants plats de coller au tonneau mouillé.
Particularités :• distance entre les trous très réduite• lamages des deux côtés• des lamages chevauchants peuvent être fraisés pour les composants collants
Perforation en fenteGrâce au chevauchement du fraisage des fentes, la stabilité des plateaux individuels reste intacte. La qualité excepti-onnelle du matériau des tonneaux permet une perforation très proche. C’est pourquoi même des composants au poids élevé ne posent aucun problème.
Perforation en demi-luneParmi les différents types de perforation, la perforation en demi-lune offre la gamme de produits la plus complète (clous, vis, pièces, composants emboutis et cintrés, etc.). Un espace de perforation considérablement plus important de plus de 30 % (par exemple, par rapport à une perforation ronde équivalente) garantit un meilleur échange électroly-tique. Au moyen d’outils de fraisage spéciaux, les plateaux jusqu’à 20 mm peuvent facilement être perforés en demi-lu-ne, ce qui permet une durée de vie considérablement plus longue. La forme conique sur l’extérieure permet une pénétration rapide et un égouttage rapide de l’électrolyte.
Perforation en fente longueSimilaire à la conception de la perforation en demi-lune, la perforation en fente longue offre les mêmes avantages. Elle a été conçue pour remplacer la perforation en fente sciée, car la stabilité dimensionnelle de la forme permet d’éviter un élargissement de la perforation.
120 121Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Depuis quelques années, nos pastilles ont fait leurs preuves, et pas seulement dans le domaine des tonneaux de galvano-plastie. Nos pastilles sont également utilisés dans des systèmes de filtrations et les plateaux perforés. Parmi le large choix de perforations et de conceptions, nous trouverons toujours le pastilles adapté à votre application.
Notre système de perforation des pastilles offre des avantages déterminants :
• remplacement facile des pastilles* pour une adaptation optimale aux produits• l’adhérence des composants plats est évitée grâce à la forme cintrée du pastilles• le matériau du pastilles réduit les chutes de tension et les pertes de fonctionnement• de larges chanfreins vers l’extérieur permettent un excellent échange de l’électrolyte grâce à l’effet
de pompe supplémentaire.
* les pastilles ne peuvent pas être réutilisés par la suite.
modèle standard
modèle concave
modèle convexe
Pastilles Gamme de produits pastilles A approx. 40 mm / matériau : PP
Gamme de produits pastilles E approx. 23 mm / matériau : PP
Pos. Nom Numéro de référence
1 0,25 fente 90000100
2 0,4 fente 90064500
3 0,6 fente 90117800
4 1,3 fente 90018400
5 1,3 fente concave 90081800
6 1 x 1 90000400
7 1,75 x 1,75 90070300
8 2 x 2 90000500
9 2 x 2, convexe 90000700
10 2 x 2, convexe 90037950
11 3 x 3 90000800
12 3 x 3 convexe 90000900
13 8 x 8 convexe 90018300
14 0,25 fente avec trame 2 x 2 90000300
15 demi-lune 1,3 mm 90823700
Pos. Nom Numéro de référence
1 0,25 fente 90001300
2 0,4 fente 90019500
3 0,4 x 0,4 90117600
4 1 x 1 90017100
5 1 x 1 convexe 90001400
6 2 x 2 90098900
122 123Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Notre gamme de petits tonneaux est fréquemment utilisée dans de nombreuses applications visant le traitement rationnalisé des petites séries ou pièces. Légers et faciles à manipuler, ils permettent de traiter des lots pouvant peser jusqu’à 13 kg. Un palan à chaîne permet d’augmenter le poids de 30 kg max. par lot.
Le tonneau standard est en polypropylène, d’autres matéri-aux sont toutefois disponibles. Par exemple, les tonneaux en PVDF ont permis d’obtenir d’excellents résultats dans le domaine du nickelage.
Afin de réduire au minimum les pertes résiduelles, le tonneau est soudé et les soudures lissées, ce qui évite en outre que l’article ne reste coincé. Les parois frontales rainurées empêchent les pièces plates de coller. La porte, grandement dimensionnée, permet de charger et de décharger facilement.
Le verrouillage de la porte assure une fiabilité élevée et une commande simple. Le logement et la forme de la porte sont conçus de telle manière que les petites pièces ne peuvent pas passer entre la porte et le tonneau.
Groupes de petits tonneaux
Pour transmettre le courant de galvanisation à l’article, il est possible de choisir parmi plusieurs contacts. Vous trouverez ici à titre d’exemple le contact classique, ainsi que des contacts à disque, à plot, à broche, etc.
Il est également possible d’utiliser une station d’accueil pour l’exploitation par batterie et d’équiper le groupe d’un pendule, d’un inverseur et/ou d’un vibrateur. Par ailleurs,
une injection d’électrolyte peut être montée pour faciliter l’échange électrolytique.
En résumé, la gamme de petits tonneaux convient parfaite-ment au traitement de surface rationnalisé des métaux. Le petit tonneau est indispensable dans les domaines des composants électroniques, de l’orfèvrerie, des petites séries, de la galvano-plastie en sous-traitance, de la recherche et développement.
124 125Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Porte de protection
Paniers avec contact
Parois frontales réglables
Ouverture du panier
• protection du groupe propulseur en polypropylène
• protection contre les solutions et les vapeurs du procédé
• Les contacts utilisés sont des broches, placées au centre des paniers. Ces broches peuvent être équipées d’un contact sur un côté, des deux côtés ou en continu et sont individuellement interchangeables.
• L’ouverture dans les paniers peut être adaptée aux articles, par exemple hexagonale ou rectangulaire. Les paniers sont équipés en série d’une ouverture ronde.
• L’angle d’ouverture généreux de 135° permet de remplir facilement le panier.
Conçus spécialement pour les pièces plates ou rondes en forme de barre, ces groupes sont disponibles sous forme de tonneaux simples ou doubles. Les parois intermédiaires étant amovibles, le tonneau peut être divisé en plusieurs compartiments. Ces groupes sont conçus pour des lots de plus de 300 kg et des longueurs de 2 500 mm max.
Groupes de tonneaux « satellite »
• Les parois intermédiaires étant amovibles et réglables, le tonneau peut être divisé en plusieurs compartiments. Elles sont réglées par une goupille, permettant d’obtenir une liaison par engagement positif.
Barres de transport
Systèmes de contact
Palier
Porteur de tonneau
• barres de transport pour palans à chaîne ou chariot• sur demande, contact courant moteur dans le chariot
• contacts à lame en série• contacts courant moteur, montés sur ressort• dispositifs de nettoyage des contacts• en option, rail de liaison équipotentielle• sur demande, autres barres de transport disponibles• vaste gamme de modèles standard
• palier lisse métallique résistant aux liquides
• en acier ou en inox, sans torsion• revêtement époxy anti-corrosif, décapé
et passivé ou caoutchouté• finition sur mesure pour tous les porteurs
• motoréducteurs coaxiaux SEW• protection de surface OS3• modèles spéciaux• sur demande, réglage de la vitesse
et contrôle du balancement• frein en option
Entraînement du tonneau
126 127Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Châssis rotatifs conducteurs et non conducteursContacts rotatifs
Nos châssis rotatifs conviennent parfaitement aux pièces aux géométries complexes, telles que trous borgnes, contre-dépouilles ou poches, à l’intérieur desquelles des bulles d’air peuvent se former. Dans ce contexte, l’article est
fixé seul dans des dispositifs spéciaux ou dans des paniers installés sur ces châssis rotatifs, ce qui permet de garantir un traitement régulier et d’éliminer les défauts.
Les contacts rotatifs conducteurs, conçus pour le logement d’une à deux pièces à plaquer, constituent une autre application. Ils sont fréquemment utilisés dans l’électrofor-mage ou les procédés de chromage dur. Exemples d’appli-cations : revêtement des rouleaux de gaufrage ou des tiges
de piston. Ici, les poids unitaires de plusieurs centaines de kilos sont fréquents. N’hésitez pas à nous contacter pour votre domaine d’application personnel afin de convenir d’un rendez-vous.
128 129Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Ces tonneaux complets sont spécialement fabriqués selon les exigences des clients. La perforation peut être espacée selon vos spécifications. Ils sont équipés de nos porteur de tonneau et de nos portes de protection standard.
Les corps de tonneaux et les barres porteuses sont com-posés d’acier inoxydable. Vous pouvez choisir entre de l’acier 1.4301, 1.4401 ou 1.4571.
Tonneaux pour le décapage et le phosphatage en acier inoxydableDispositif d’ouverture et de fermeture automatique du porte (DOS) Processus d’ouverture du porteLe dispositif d’ouverture de porte élève automatiquement le tonneau de galvanoplastie en position de chargement et de déchargement, se prépositionne et est ensuite ajusté. Dès que ce positionnement est terminé, le processus réel d’ouverture du porte commence.
Il se déroule comme suit : Les outils d’ouverture du porte sont inclinés et s’engagent dans les renfoncements des loquets du porte avec l’extension du vérin de levage. La conception des outils de préhension garantit une prise en douceur des loquets et un maintien fiable du porte dans le dispositif d’ouverture du porte.
Comme les outils d’ouverture du porte sont reliés par une barre plate, chaque outil individuel est assuré d’avoir un angle d’inclinaison identique à tout moment.
Une fois que le porte a été soulevé par le dispositif d’ouverture, le dispositif revient à sa position initiale avec le porte. Le tonneau peut maintenant être chargé ou déchargé sans entrave.
Le nombre de mouvements est réduit au minimum grâce à la conception simple de ce dispositif de chargement et de décharge-ment. Cela apporte un certain nombre d’avantages déterminants en termes de rentabilité, de fiabilité et de durée de vie.
Processus de fermeture du porteLe porte est fermé de la même façon qu’il a été ouvert, mais dans l’ordre inverse. Le dispositif replace toujours le porte de façon fiable et précise sur l’ouverture du tonneau.
130 131Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Lorsque nous concevons un tonneau de polissage électroly-tique, nous sommes particulièrement vigilants à la qualité des produits finis. Notre tonneau de polissage électrolytique permet pour la première fois de polir des produits d’un volume maximum de 8 litres ou d’un poids maximum de 25 kg et toujours avec une qualité optimale constante.
Aperçu des avantages de ce tonneau • fabrication soignée à l’aide de matériaux de haute qualité
qui garantit une longue durée de vie même dans des conditions extrêmes
• construction du système solide adaptée à l’application prévue
• porte précis et fermé hermétiquement• utilisation facile et sécurité opérationnelle répondant
même aux exigences les plus élevées grâce au système de fermeture du porte
• paliers stables• échange optimal de l’électrolyte et pertes de fonctionne-
ment réduites au moyen de matériau de surfaces lisses et hydrofuges et de transferts sans jeu combinés à un système de perforation sophistiqué
En cas de remplissage du volume du tonneau à 80 % (env. 8 litres), le courant fourni avoisine les 500 – 600 A à une tension de 6 – 10 V. Le cycle d’électropolissage dure entre 5 et 15 minutes en fonction de la condition du matériau de départ. Grâce à l’électronique de commande développée en sus, un réglage continu de la vitesse ainsi qu’un fonctionne-ment oscillant sont possibles.
Les paliers à coussinet en métal étanches transfèrent directement le courant sur le corps du tonneau en titane ou en acier inoxydable. Le fluide de contact spécial dans la partie intérieure du palier maintient les surfaces de contact propres. Ce système permet des transmissions de courant de jusqu’à 500 A par côté.
Le corps à double paroi du tonneau et le tube central à double paroi sont complètement résistants aux courts-cir-cuits. Une paroi transfère le courant anodique, l’autre transfère le courant cathodique.
Tonneau de polissage électrolytique
TransmissionNous utilisons des moteurs réducteurs de grande qualité avec disjoncteurs pour la transmission. La tension du moteur est de 12 V ou 24 V en courant continu. De plus, la vitesse du tonneau peut être ajustée en continu sur le système.
Support de contactPour le transfert de courant galvanique, nous utilisons généralement des contacts à lame en cuivre, également adaptés aux courants forts.
Corps du tonneauLe corps du tonneau est composé de titane et d’acier inoxydable 1.4571. Le palier à coussinet en métal étanche permet une transmission de courant jusqu’à 500 A. La forme spéciale du porte garantit un ajustement sans jeu. Le porte peut être fermé ou ouvert sans difficulté à l’aide d’un loquet rotatif pratique.
Barres de transportLa barre de transport du tonneau de polissage électroly-tique possède une manille. Sur demande, nous pouvons également fournir d’autres types de barres de transport. Dans la plupart des cas, il est possible d’adapter les barres ou le porteur complet.
132 133Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Le contact courant moteur est un élément important d’un tonneau complet qui fonctionne correctement. Nos contacts courant moteur possèdent des avantages déterminants et assurent un fonctionnement sans problème de votre installation.
Avantages :• surfaces de contact autonettoyantes• transmission de courant très fort (jusqu’à 60 A)• extrêmement robuste et donc très fiable• construction pratique pour la maintenance et la réparation
Les supports de cuves sont disponibles en versions conductrices ou sans courants et peuvent être fabriqués selon vos spécifications. Les tailles et les formes standard sont en stock.
Contact courant moteur
Supports de cuve
Ce « tonneau à l’intérieur d’un tonneau » peut être utilisé pour galvaniser des petits lots en plaçant simplement le mini tonneau dans le tonneau existant. Le corps est en PP gris et est équipé de vis avec des écrous borgnes en acier inoxyda-ble comme contacts.
Deux tailles sont disponibles avec des diamètres internes de 50 mm et 100 mm. Vous pouvez choisir la longueur. Pour le
mini tonneau avec un diamètre interne de 100 mm, les contacts sont également montés sur le côté avant. La perforation standard est ronde avec un diamètre de 6 mm. Des perforations et des formes spéciales sont disponibles sur demande.
Mini tonneau
134 135Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Tonneaux de galvanoplastie & groupes FR
Nous fabriquons nous-mêmes tous nos engrenages, de la pièce unique à la petite série : des engrenages pour les groupes de petits tonneaux aux engrenages complexes, tout est possible.
Le PE 1000 est le matériau le plus fréquemment utilisé, d’autres, tels que les PE 500, PP, PPS, inox, etc., sont également disponibles. Il est également possible de combiner le plastique et le métal.
Engrenages Contacts pour courant fort et dispositifs de nettoyage
Des idées pour la galvanoplastie et le courant fort !
136Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Contacts à courant fort FR
Ils convainquent par leur conception simple. Une concep-tion soudée résistante, en inox de qualité, assure une utilisation durable sans problème. Les plaques de contact sont appuyées fortement par des ressorts contre les surfaces de contact, permettant un excellent passage du
courant électrique. De simples câbles d’alimentation sont branchés directement sur les plaques de contact. En cas de mouvement des articles, toute autre tresse n’est pas nécessaire. Robustes, peu de maintenance, prix avanta-geux et autonettoyants.
Contacts de surface
Surveillance• en option, surveillance des
contacts par des sondes PT100
Capots• capots en acier 1.4301 pour la
protection contre la chute de boues
Conception inox résistante• console en acier 1.4301 dotée de guidages
résistants, conception soudée• en option, en acier 1.4571, avec revêtement
ou avec d’autres guidages PE
Ressorts de pression• ressorts de pression isolés en
acier pour une pression constante• revêtement anti-corrosif en option
Raccordement• Droit ou angulaire pour un
branchement facile des tresses
Plaque de contact interchangeable• plaques de contact faciles à
remplacer, dotées de rainures à séparation pour l’autonettoyage au moment de l’entrée
138 139
1500 A 3000 A
Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
Conception pneumatique Les contacts pneumatiques ne sont utilisés que là où il faut relever des défis en termes de courants très élevés, d’espace restreint ou de faibles poids d’entrée. La pression est assurée par un coussinet pneumatique en caoutchouc vulca-nisé. Le domaine d’application des contacts pneumatiques est pratiquement illimité, les contacts de 20 kA et plus sont fréquents. Le refroidissement par eau en option permet d’augmenter la puissance à tout moment. Les coûts sont certes relativement élevés mais leur utilisation permet d’obtenir une fiabilité à toute épreuve.
Coussinet pneumatique• entraînement pneumatique avec
utilisation d’un coussinet pneumatique en caoutchouc vulcanisé
Ressorts de pression• ressorts de pression isolés en acier
pour une pression constante• revêtement anti-corrosif en option
Plaque isolante• en PPS ou HGW (stratifié industri-
el rigide) pour protéger le coussi-net pneumatique de la chaleur
Refroidissement par eau• en option, refroidissement par eau pour
augmenter la puissance
Plaques de contact• plaques de contact faciles à remplacer,
dotées de rainures à séparation pour l’autonettoyage au moment de l’entrée
Console• console en acier 1.4301 dotée de
guidages résistants, conception soudée• en option, en acier 1.4571, avec
revêtement ou avec d’autres guidages PE
Contacts de surface avec entraînement pneumatique et refroidissement par eau
Refroidissement par eau Si vous souhaitez augmenter la puissance de sortie d’un contact de surface courant, il est recommandé d’avoir re-cours à un refroidissement par eau. Un contact de surface refroidi par eau permet d’augmenter la puissance de sortie maximale de plus de 35 % en fonction de la capacité de refroidissement. Le refroidissement par eau est placé direc-tement dans les plaques de connexion. Il est recommandé d’utiliser des sondes PT100 pour assurer la surveillance opti-male des contacts, garantissant ainsi leur exploitation fiable.
Capots• capots en acier 1.4301
pour la protection contre la chute de boues
Raccordement• droit ou angulaire pour un
branchement facile des tresses
Surveillance• en option, surveillance
des contacts par des sondes PT100
140 141Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
Quelle que soit l’installation, il est possible d’adapter les contacts disponibles. Tous nos systèmes sont éprouvés et, en fonction du modèle, il est possible d’augmenter leur puissance.
Modification simple des contacts disponibles
Logement en prisme
Logement de l’épée de contact
Logement pour pivot ronde
Logement en V
Ces contacts dotés de plusieurs doigts, montés sur ressort, assurent une excellente connexion électrique, même en cas de surfaces irrégulières au niveau du porteur. Idéalement, les doigts sont dotés de rainures à séparation qui éliminent
la boue superficielle au moment de l’entrée du porteur. Plusieurs rubans relient les éléments mobiles et le corps de base.
Un coussinet pneumatique permet d’augmenter la pression de contact afin d’obtenir une connexion électrique accrue. Notamment dans les installations anciennes, force est de
constater que les surfaces de contact des porteurs sont souvent irrégulières. Dans ce cas, il est donc judicieux de choisir des contacts à doigts pneumatiques.
Contacts à doigts
Contacts à doigts pneumatiques
142 143Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
Formes spéciales et logements
Contacts à boulonsUtilisés au début de l’automatisation des installations de galvanoplastie, on les trouve aujourd’hui encore sous forme de contacts à anodes et pour les cellules d’électrolyse. Le corps de base, en laiton massif, est monté directement sur le rail de raccordement. D’autres connexions ne sont donc plus nécessaires.
Les boulons, montés sur ressort, reliés à des lamelles de contact, sont à l’intérieur du contact. L’intensité du courant maximal dépend du nombre de boulons de contact. Chaque boulon est en mesure de transmettre env. 400 A. Générale-ment, il est toutefois recommandé d’utiliser un contact de surface courant fort, moins cher.
On les trouve souvent dans les installations pour circuits imprimés en raison des poids d’entrée toujours faibles. L’utilisation de contacts glissants implique une précision d’entrée élevée et une position exacte des contacts. En
raison des possibilités de compensation limitées, ils ne conviennent pas aux appuis à 3 ou 4 points. Tout comme les logements en laiton, les contacts glissants ne sont pas autonettoyants.
Contacts glissants
On les utilise depuis plus de 100 ans. Au tout début de la galvanoplastie industrielle, on utilisait, outre les logements en laiton, uniquement des contacts à ressort courbés. En cas de faible intensité, allant jusqu’à 500 A, ces contacts
sont encore aujourd’hui amplement suffisants. Certes avantageux du point de vue du prix et dotés de bonnes propriétés mécaniques, ils ne sont toutefois pas autonet-toyants et doivent donc être souvent nettoyés.
Nos contacts ne sont pas uniquement destinés à la galvano-plastie. Nous proposons également des solutions spéciales, par exemple pour des installations de maintenance de trains, des systèmes de changement rapide pour les outils de
presse, des fours sous vide, des bancs d’essai, des installa-tions de recyclage et des installations spéciales pour l’aéronautique.
Contacts spéciaux
Logements en laiton
144 145Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
Ce qui était valable il y a 90 ans, l’est encore aujourd’hui. Seuls des contacts propres sont efficaces.
Pour aider le personnel, il est recommandé d’utiliser des dispositifs de nettoyage au niveau des bains de rinçage. Ces dispositifs fonctionnent indépendamment de l’opérateur. Les surfaces de contact du porteur sont nettoyées au cours de chaque cycle.
Ici, la conception simple et robuste est un grand avantage. Chacune des brosses peut être remplacée. Les dispositifs de nettoyage sont disponibles pour chaque type de contact (épée, pivot, prisme, etc.). Généralement, il est facile de remplacer les dispositifs de nettoyage par les logements en plastique existants.
Dispositifs de nettoyage
« Les débutants oublient facilement la propreté des contacts et des conducteurs bien que ce soit un élément essentiel dans le passage du courant et, par conséquent, dans l’électrodéposition. »
Dr. W. Pfanhauser, Galvanotechnik, [Galvanoplastie] 1928
Conception inox résistante • en acier 1.4301• gabarit des trous de fixation conformément
à vos exigences
Cales montées sur ressort en PE 1000• pour le logement des brosses• régler les cales via les vis à six pans creux
Brosses interchangeablesen acier 1.4301• Les brosses peuvent être remplacées directe-
ment sur le récipient, tout démontage du dispositif de nettoyage est inutile.
146 147Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
Pour le branchement des contacts courant fort voire même de redresseurs, nous recommandons l’utilisation de câbles d’alimentation ultra flexibles. Nous proposons différents modèles et sections pour répondre à vos exigences. Au choix, les câbles sont composés de brins de cuivre avec embout serti ou cosse. En fonction de l’application et de l’environnement, les câbles d’alimentation sont équipés de flexibles de protection en PVC, silicone ou PUR et sertis de manière étanche. Nous vous aidons volontiers à choisir le câble qui vous convient.
Câbles d’alimentation et tresses
Logements en plastique
Accessoires
En règle générale, ils sont en PE ou PP. Vous avez le choix entre nos logements standard d’un prix avantageux ou un logement personnalisé. Nos centres d’usinage CN 5 axes nous permettent de réaliser même les géométries complexes. Généralement, il suffit d’un échantillon ou d’un croquis.
Rails en cuivre
Notre parc de machines de découpe et de pliage, moderne et performant, nous permet de fabriquer et de monter sur place les rails en cuivre. Dans ce contexte, le cuivre brut est découpé sur place avant d’être poinçonné et plié pour l’adapter exactement aux conditions ambiantes.
Tous les rails sont livrés sur demande avec accessoires de montage, isolations et caches.
Dans la plupart des cas, il est possible de modifier les rails existants ou de remplacer certains segments sans aucun problème.
En association avec nos contacts ou groupes modulaires, vous obtenez tout d’un seul et même fournisseur, du redresseur au récipient, vous garantissant ainsi la compati-bilité la plus élevée.
148 149Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
Groupes modulaires
Accessoires
Il s’agit d’un équipement pré-assemblé pour fourniture au bord de cuve : les logements en plastique, les fourches de réception, les contacts courant fort, les contacts courant moteur et les dispositifs de nettoyage sont montés dans
l’agencement et en nombre souhaités. Ces modules peuvent être vissés ou soudés en bloc, ce qui évite les travaux d’alignement pénibles de chaque composant.
Paniers anodiques Nous vous proposons plusieurs tailles et modèles. Forme et nature de la fixation en fonction des desiderata du client. Nous sommes également en mesure de réaliser ces paniers d’après des croquis ou des échantillons.
ChâssisOutre les contacts courant fort et les groupes de tonneaux, nous proposons également de nombreux composants classiques pour châssis : des attaches avec serre-flanc « Lipfix » aux têtes et cales en passant par les pinces d’anode. Nous vous fournissons tout ce dont vous avez besoin pour vos porteurs. Plusieurs finitions spéciales, petites séries et pièces uniques sont disponibles sur demande. N’hésitez pas à nos contacter.
Il s’agit de câbles d’installation résistants avec une gaine PUR. Spécialement fabriqués pour nous, ils sont disponib-les en plusieurs diamètres et sections. Plusieurs applica-tions spéciales (câbles en PVC, silicone et néoprène) sont disponibles sur demande. Nos bulbes de contact sont
disponibles en acier, en laiton, en inox ou autres matériaux spéciaux, tels que le titane ou le cuivre. Outre les formes creuses, filetées, continues, nous proposons également d’autres formes spéciales. N’hésitez pas à nous contacter pour une longévité accrue de cette pièce d’usure.
Câbles de contact
150 151Conseils personnalisés et commandes : par téléphone au : +49 23 71 / 15 75-0 ou par email à [email protected]
Des idées pour la galvanoplastie et le courant fort !
Contacts à courant fort FR
152 153Persönliche Beratung und Bestellungen: +49 23 71 / 15 75-0 oder an: [email protected]
Ideen für Galvano- und Hochstromtechnik!
Notizen / Notes / Note
Für Satz- und Druckfehler gewähren wir keine Haftung. Alle Maße in Zeichnungen und Skizzen sind in Millimetern angegeben. Alle Änderungen, die dem technischen Fortschritt dienen, bleiben uns vorbehalten. Die in diesem Katalog abgebildeten Aggregate können kundenspezifische Anfertigun-gen sein und Sonderzubehör enthalten. Unsere allgemeinen Geschäfts- und Lieferbedingungen können Sie im Internet einsehen und herunterladen oder erhalten diese auf Anfrage von uns zugesandt.
We are not liable for typographical and printing errors. All dimensions in drawings and sketches are given in millimeters. We reserve the right to make all changes in the interest of technical progress. The units shown in this catalogue may be custom-made and may contain special accessories. You can view and download our general terms and conditions on the Internet or we will send them to you upon request. Sous réserve d’erreurs typographiques. Toutes les chiffres dans les plans et croquis sont indiqués en millimètres. Sous réserve de modifications techniques. Visuels non contractuels. Vous pouvez consulter nos conditions générales de vente et les télécharger sur notre site internet ; si vous le souhaitez, nous pouvons également vous les envoyer.
Linnhoff & Partner Galvanotechnik GmbH Lünkerhohl 32 a 58644 Iserlohn Germany
Telefon: +49 (0) 2371/1575-0 Telefax: +49 (0) 2371/1575-29 E-Mail: [email protected] www.linnhoff-partner.com
Ideen für Galvano- und Hochstromtechnik!Ideas for electroplating and high current!
Des idées pour la galvanoplastie et le courant fort !