Geometric Representation of Angles. Angles Angles Initial Side and Standard Position Initial Side...

18
Geometric Representation of Angles

Transcript of Geometric Representation of Angles. Angles Angles Initial Side and Standard Position Initial Side...

Page 1: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Geometric Representation of Angles

Page 2: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Angles

Initial Side and Standard Position

Page 3: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Degrees: One degree is 1/360 of a revolution.

A right angle is an angle that measures 90 degrees or ¼ revolution

A straight angle is an angle that measures 180 degrees or ½ revolution

Page 4: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Drawing an Angle

(a) 45 degrees

(b) -90 degrees

(c) 225 degrees

(d) 405 degrees

Page 5: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

1 degree equals 60’ (minutes)

1’ (minute) equals 60” (seconds)

Using graphing calculator to convert

Page 6: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Definition

Arc Length For a circle of radius r, a central angle of

radians subtends an arc whose length s is

s=r

Page 7: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Find the length of the arc of a circle of radius 2 meters subtended by a central angle of 0.25 radian.

s=rwith r = 2 meters and Θ = 0.25

2(0.25) = 0.25 meter

Page 8: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

One revolution is 2π therefore, 2πr = rθ (arc length formula)

It follows then that 2π = θ and

1 revolution = 2π radians 360 degrees = 2π radians or 180 degrees = π radians so . . . 1 degree = π/180 radian and 1 radian = 180/π degrees

Page 9: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Convert each angle in degrees to radians:

(a) 60 degrees (b) 150 degrees (c) – 45 degrees (d) 90 degrees

Page 10: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Convert each angle in radians to degrees

(a) π/6 radian (b) 3π/2 radian (c) -3π/4 (d) 7π/3

Page 11: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Page 375 has common angles in degree and radian measures

Page 12: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Steps: (1) Find the measure of the central angle

between the two cities (2) Convert angle to radians (3) Find the arc length (remember we live

on a sphere and the distance between two cities on the same latitude is actually an arc length)

Page 13: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

The area A of the sector of a circle of radius r formed by a central angle of θ radians is

A = ½ r^2θ

Examples

Page 14: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Linear Speed:

v = s/t

Angular Speed:

ω = θ/t

Page 15: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

Angular Speed is usually measured in revolutions per minute (rpms).

Converting to radians per minute

Linear Speed given an Angular Speed:

v = rω where r is the radius

Page 16: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

A child is spinning a rock at the end of a 2-ft rope at the rate of 180 rpms. Find the linear speed of the rock when it is released.

Page 17: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

At the Cable Car Museum you can see four cable lines that are used to pull cable cars up and down the hills of San Francisco. Each cable travels at a speed of 9.55 miles per hour, caused by rotating wheel whose diameter is 8.5 feet. How fast is the wheel rotating? Express your answer in rpms.

Page 18: Geometric Representation of Angles.  Angles Angles  Initial Side and Standard Position Initial Side and Standard Position.

On-line Examples

On-line Tutorial