Furuno Ro4800 Operators Manual
-
Upload
stuart-eastland -
Category
Documents
-
view
201 -
download
9
description
Transcript of Furuno Ro4800 Operators Manual
-
RO4800 VHF Marine Radio
Furuno
Furuno
Draft Ver: V2.0, date: NOV 12, 08 Prepare by: IDT
Furuno
P4800 Wireless Microphone
-
T
-
P4800
3
MOB SETUP
7.4.3 GPS REDIR
-
Furuno RO4800
P4800
1
2
13 5 116 3
12 7 10
9
8
4
-
42 1
5
7
6
3
-
/ ! : #? & ZS
in USA brand
FAVORITE
-
RO4800
RO4800
the
-
RUBBER PAD
M5
M5X32
M5X10
WALL
Fig: 3.7 Recessed InstallationFig: 3.6 Mounting The Handset
-
Hold down the Cancel/IC button until the LCD appears the
-
FURUNO
-
,Press advance
Press then knob
-
select CALL BACK the follow
select CALL BACK the follow
-
POSITION REQ
ENT ACK
CANCEL EXIT
FROM
-
can by pressing the CH knob
by pressing
-
of POS and Time,
Time offset,
4
, Band rate setting and GPS REDIR selecting
MOB SET UP Subscribe to link the MOB,and display the MOB state
to
to pop up on
-
Select LOCAL/DIST
then scroll to LOCAL,press the CH knob.
on its LCD
POSITION!!
is
-
CH NAME
DISPLAY NAM
KEY
-
DSC ENABLE
6.12 MOB SET UP
Register your MOB to the base unit, and you can review the MOB is ON/OFF
status by this menu.Please ref. to chapter 9.
-
Furuno radio RO4800
Furuno
3
-
FURUNO
BAUD RATE
-
MOB SETUP
In List or Plotter mode, press the knob to enter the info. mode.
7.4.3 BAUD RATE
User can choose between output the AIS data in 4800 or . The
default setting is 38400.
1. Select MENU SELCET,then AIS SETUP.
2.Select BAUD RATE,the cursor is at 38400(Which is the default
setting),Select your desired then press the CH knob to confirm your
choice.
3.If 4800 is selected,press the CH knob to advance to the warning
page.Select YES then press the CH knob to change the baud rate from
38400 to 4800.
7.4.3 GPS REDIR
The GPS redirection option is set to output the GPS information to the
chartplotter. So, no extra multiplexer is needed.
If 'yes' is selected, the $RMC will be redirected to the chartplotter once
we received. ( If no $RMC, other GPS sentance would be outputed
(e.g. GLL) however, we won't output all in the same time because it
may add too much loading in the slow traffic)
38400
-
P4800
P4800
FURUNO
FURUNO
1
2
3
4
5
7
6
12
11
8
9
13
10
1.Select MENU SELCET,then AIS SETUP.
2.Select GPS REDIR the cursor is at NO select your desired then
press the CH knob to confirm your choice.
, ,
-
FURUNO
P4800
the radio unit.
DSC SETUP
AIS SETUP
HS SETTING
MENU SETUP
DSC SETUP
AIS SETUP
CODE
WAITING
-
During scan press
HI/LO /SCAN
HI/LO /SCAN
Press
,again press to turn back watch mode. To
HI/LO /SCAN
DSC/MENU
During watch mode
scroll
-
3
-
8 Abnormal or No display
on Wireless Handset.
Reset by removing the batteries for around 30 seconds.
This will return the unit to the default settings.
RO4800
-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30