Fast Trac August 2015
-
Upload
fastserv-supply -
Category
Documents
-
view
230 -
download
2
description
Transcript of Fast Trac August 2015
Ed. 1
5 Vo
l. 8
LAG SCREWS — HEX ZINC
G
H
D
LF
Material: Steel
Plating: ZincDiameter D 1/4” 5/16” 3/8” 1/2” 3/4”Height H 11/64 7/32 1/4” 11/32 1/2W.A.F. F 7/16 1/2 9/16 3/4 1-1/8W.A.C. G .505 .577 .650 .866 1.299
Part No. D LF17538 1/4” 1”F117479 1/4” 1-1/4”F16665 1/4” 1-1/2”F118266 1/4” 1-3/4”F15054 1/4” 2”F12553 1/4” 2-1/2”F11658 1/4” 3”F17360 1/4” 3-1/2”F115223 1/4” 4”F16218 1/4” 4-1/2”F119335 1/4” 4-1/2”F119529 1/4” 5-1/2”
Part No. D LF112043 1/4” 6”F113803 5/16” 1”F16263 5/16” 1-1/2”F111012 5/16” 1-3/4”F120037 5/16” 2”F111018 5/16” 2-1/2”F11378 5/16” 3”F111309 5/16” 3-1/2”F19833 5/16” 4”F113199 3/8” 1”F15193 3/8” 1-1/2”F119515 3/8” 1-3/4”
Part No. D LF112981 3/8” 2”F111405 3/8” 2-1/2”F116548 3/8” 3”F111770 3/8” 3-1/2”F13148 3/8” 4”F117660 3/8” 4-1/2”F113059 3/8” 5”F113091 3/8” 5-1/2”F17779 3/8” 6”F15505 1/2” 1-1/2”F11335 1/2” 2”F11743 1/2” 2-1/2”
Part No. D LF115002 1/2” 3”F12961 1/2” 3-1/2”F111079 1/2” 4”F110560 1/2” 4-1/2”F119910 1/2” 5”F118312 1/2” 5-1/2”F14838 1/2” 6”F14883 1/2” 7”F1705 1/2” 8”F16145 3/4” 4”F119155 3/4” 4-1/2”F11920 3/4” 5
G
H
D
LF
Part No. D LF15149 1/4” 1”F113525 1/4” 1-1/4”F112878 1/4” 1-1/2”F113411 1/4” 2”F15180 1/4” 2-1/2”F113613 1/4” 3”F17629 1/4” 3-1/2”F119538 1/4” 4”F19463 1/4” 4-1/2”F112845 1/4” 5”F12136 1/4” 6”
Part No. D LF118265 5/16” 1”F116324 5/16” 1-1/4”F117576 5/16” 1-1/2”F16872 5/16” 2”F117971 5/16” 2-1/2”F112297 5/16” 3”F17475 5/16” 3-1/2”F113663 5/16” 4”F13172 5/16” 4-1/2”F116296 5/16” 5”F18611 5/16” 6”
Part No. D LF14003 3/8” 1”F14797 3/8” 1-1/2”F112898 3/8” 2”F18639 3/8” 2-1/2”F113474 3/8” 3”F1110 3/8” 3-1/2”F112890 3/8” 4”F18428 3/8” 5”F13522 3/8” 6”F14310 1/2” 1-1/2”F111397 1/2” 2”
Part No. D LF119534 1/2” 2-1/2”F112537 1/2” 3”F1988 1/2” 3-1/2”F19374 1/2” 4”F16173 1/2” 4-1/2”F16540 1/2” 5”F113053 1/2” 6”
ANSIB18.2.11981
Material: 18-8 Stainless Steel
Plating: None
Diameter D 1/4” 5/16” 3/8” 1/2”Height H 11/64 7/32 1/4” 11/32W.A.F. F 7/16 1/2 9/16 3/4W.A.C. G .505 .577 .650 .866
SCREWS — HEX HEAD LAG 18-8 STAINLESS STEEL
ANCHORS — LAG SHIELDS
• Used for light to medium duty fastening• Can be used in concrete, mortar joint,
masonry and brick• Lag screw must protrude at least a 1/4”
out from the bottom of the anchor to insure proper expansion
• Made of high quality zinc alloy• Rustproof
Part No.AnchorSize Length
HoleSize
Part No.For Box
BoxQty.
F119578 1/4” 1” 1/2” F119578B100 100F11754 1/4” 1-1/2” 1/2” F11754B100 100F119922 5/16” 1-1/4” 1/2” F119922B100 100F1463 5/16” 1-3/4” 1/2” F1463B100 100F117128 3/8” 1-3/4” 5/8” F117128B50 50F113812 3/8” 2-1/2” 5/8” F113812B50 50F118551 1/2” 2” 3/4” F118551B25 25F18539 1/2” 3” 3/4” F18539B25 25F114561 5/8” 3-1/2” 7/8”
FASTENERS
We know MROPAGE 2
• Cleaner, degreaser and deodorizer• For industrial and institutional applications• Safe product for use in many areas of industry• Will not dull most surfaces• Versatile & economical• Non-flammable• Dilution: heavy duty: 1:10 medium soil: 1:20 light duty: 1:30• Fragrance: Sassafras• For concrete floors, counters, drains, engines, fireplaces,
garbage containers, aluminum siding, boat exteriors, vehicle exteriors, carpets, fiberglass, wood, painted surfaces, polished stone, pressure washing, stainless steel, tile, walls and equipment
ISI POLY MR. GREENWATER BASED CLEANER
Part No. PackageF32238 1 QuartF3938 12 x 1 QuartsF31617 1 GallonF31602 6 x 1 GallonsF31046 5 Gallon PailF31289 55 Gallon Drum
THUMB SCREWS
UNC UNF D LF16717 #6 1/2”F116127 #6 3/4”F17071 #8 3/4”F19028 #8 1”F117968 F19611 #10 1/2”F13230 F111879 #10 3/4”F120013 F19545 #10 1”F118038 1/4” 1/2”F116307 1/4” 3/4”
UNC UNF D LF17146 1/4” 1”F119652 1/4” 1-1/4”F113684 1/4” 1-1/2”F114924 1/4” 2”F12006 1/4” 2-1/2”F110874 1/4” 3”F114415 5/16” 1/2”F199 5/16” 3/4”F16285 5/16” 1”
UNC UNF D LF18326 5/16” 1-1/4”F114092 5/16” 1-1/2”F13817 5/16” 2”F11587 3/8” 3/4”F15715 3/8” 1”F114048 3/8” 1-1/2”F113558 3/8” 2”F117563 3/8” 2-1/2”F119298 3/8” 3”
ASME B18.6.8
Material: Steel
Plating Zinc
Nominal Size (D) #6 #8 #10 1/4” 5/16” 3/8”Thread Pitch 32 32 24 or 32 20 18 16Head Width Max (A) .45 .51 .58 .83 .96 1.09Head Height Max (B) .28 .32 .39 .52 .64 .71Head Thickness Max (C) .08 .09 .10 .16 .17 .22Head Thickness Max (C1) .03 .04 .05 .06 .09 .11
D
LB
CC1
A
INDIANA
• Heavy duty glass and hard surface all-purpose spray• Cleans, polishes and shines• Specially formulated with a balanced blend of cleaning agents• Quickly penetrates and removes dirt, soot, fingerprints, perspiration
and food soils• Will not streak, smear or leave smudges • Dissolves oily films that hold dirt• No phosphates• For windows, mirrors, fixtures, counters, exhaust hoods, display
cases, oven fronts, walls, floors, cabinets, chairs, telephones and porcelain surfaces
• Note to All Users in California and OTC States: must dilute 10 parts concentrate with no less than 1 part water prior to use to meet 4% by wt. VOC requirement for use as a general purpose cleaner
ISI POLY SUNNY STREAKLESSGENERAL PURPOSE CLEANER
Part No. PackageF31826 1 QuartF31769 12 x 1 QuartsF3932 1 GallonF31473 6 x 1 GallonsFW121569 5 Gallon Pail
COCKPIT PREMIUM FASTSERV RUST COATRUST CONVERTER
• Anti-static action cleans and protects in one step• All plastic interior components remain with a matte finish• Suitable for cleaning other smooth surfaces
made of glass, plastic, or painted materials• No Silicone, Body Shop Safe
Part No. Package 12-PackF3213 500ml Spray Bottle F31025 Part No.
Net Weight
Can Size
F317 13 oz (369 g) 20 fl oz
• Chemically destroys rust• Converts rust into a tough, black, paintable polymer• Seals & protects metal surfaces• Compatible with most paints, topcoats and body fillers• Works best with some rust still exposed, rust is needed for black polymer to form• Fast drying
CHEMICALS
INDIANA
FASTENERS
PAGE 3We know MRO
INDIANA
• Concentrated all purpose cleaner• Spray and wipe• Light duty to heavy soil• Removes grease, ink, crayon, pencil, lipstick,
greasy food, smoke film and much more• No excess scrubbing• No rinsing• No residue• Cleans deep, cut through and lifts soils• For painted surfaces, walls, floors, counters,
vinyl, office equipment, utensils, range hoods, truck exterior and interior, fiberglass, aluminum and much more
• Dilution: Heavy Duty: 1:2 Light Duty: 1:3• Fragrance: Pine
ISI POLY FASTBALLHEAVY DUTY ALL PURPOSE CLEANER & DEGREASER
Part No. PackageF32269 1 Quart F31108 12 x 1 QuartsF3855 1 GallonF32319 6 x 1 GallonsF31379 5 Gallon PailF3812 55 Gallon Drum
INDIANA
LOW MAINTENANCE FINISHREDUCED MAINTENANCE FLOOR FINISH
Part No. PackageF33005 1 GallonF33006 4 x 1 GallonsF33516 5 Gallons
• Extremely durable and mark-resistant finish for low maintenance applications
• High gloss acrylic polymers stay clean, clear, and shiny to reduce maintenance
• Non-yellowing, low maintenance formula offers superb black mark and scuff resistance
• Ideal for reduced burnishing programs (once per week)
• Use on vinyl tile, rubber, linoleum, terrazzo and quarry tile floors
• Excellent seal properties
NANO HIGH-SOLID FLOOR FINISHREVOLUTIONARY FLOOR FINISH
Part No. PackageF33004 GallonF33520 4 x 1 GallonsF33521 5 Gallons
Part No. Package 12 PackF3952 500ml
BottleF31272
• Nano-zinc cross-linking provides superior: lay-down gloss, gloss build, durability, mark resistance, soil resistance, dry and recoat times
• Ammonia-free for dramatically- reduced odor
• Ideal for limited maintenance programs, yet responds to daily burnishing, if desired
• Low-emissions formula - meets California’s new 1% VOC Regulation
• Fast-drying - 15 to 20 minutes under normal conditions
• Slip-resistant - UL Classified
PERLS CAR SHAMPOO
• Highly concentrated shampoo for an effortless foam wash which seals in shine
• Three-fold action: cleans quickly, durable protection, and creating deep, long lasting shine
• Instant beading after rinsing• Frequent application preserves the
paintwork finish
Part No. PackageF31576 5 Gallon PailF31214 55 Gallon Drum
• Super concentrated, premium truck and trailer wash
• Medium to high foaming• Specifically formulated to
remove bugs, road film and exhaust deposits
• Designed for use through hot or cold pressure washing equipment
• Can be used in touch free in-bay automatics and self-service washes
• Both a high pressure detergent and a low pressure presoak
• Excellent for use on mass transit equipment, trailers, trucks and fleet vehicles
• No phosphates• Fragrance: Odorless• Dilution: 1:60-150 (metering ratio)
ISI POLY FIREBALLFLEET & TRUCK WASH
INDIANA
• Unique, long lasting tropical fragrance• Non-toxic• 100% biodegradable ingredients• For cleaning kitchens, bathrooms,
household surfaces, floors and walls
ISI RED SKYEALL PURPOSE CLEANER
Part No. PackageF32982 1 QuartF32983 12 x 1 Quarts
MR.ORANGE CITRUS CLEANER & DEGREASER
Part No. PackageF32603 1 QuartF31812 12 x 1 QuartsF3385 1 GallonF31791 6 x 1 GallonsF395 5 Gallon PailF3275 55 Gallon Drum
• Natural citrus water based cleaner & degreaser• Cleans grease and heavy oil deposits from most surfaces• Drain cleaner and grease trap maintainer• Deodorizer• Concentrated • Non-butyl, non-corrosive, non-flammable, no petroleum distillates• Contains D-limonene• For: grease traps, drains, trucks and heavy equipment, engine parts, tar and asphalt removal• Dosing: degreasing: 4:1 (rinse thoroughly), pressure washing: 20:1, drain maintainer: 3-5 oz
per drain, grease trap: 5 oz daily (up to 10 oz for large capacity)• Dilution: light duty: 1:40, medium soil: 1:20, heavy duty: 1:10• Fragrance: Citrus
CHEMICALS
We know MROPAGE 4
QUIKLEEN® ABSORBENT
Part No. SizeF42324 Gallon JugF42402 Gallon Jug x 4F42325 20 lb Bag
• Quikleen® is an inert, inorganic, non-biodegradable blend of minerals. It works by means of known as “silica encapsulation”. The absorbed liquid actually becomes part of the silica molecule.
• All natural, non-toxic, non-flammable, non-biodegradable, non-leaching, reusable
• Landfill acceptable and EPA certified• 1.5 lbs of Quikleen® will absorb an entire
quart of motor oil vs 15 lbs of clay
• Absorbs oils, fuels, grease, solvents, acids (except hydrofluoric), paint, coolants, bodily fluids, sewage
Part No.F43006
Part No.F41393
Part No.FB4
Part No.F41433
Part No.F41053
Part No.F43076
Part No.F42413
3/8” DRIVE SAE 12PT SOCKET SET - 15 PIECE
• Set contains: Standard Sockets - 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4”, 13/16”, 7/8”, 1”
• Adapter 3/8” Female x 1/2” Male; Universal Joint 2”• Reversible Ratchet 8”; Extension Bars 3” and 6”
TONGUE AND GROOVE PLIERS
Part No. Description CapacityF41278 6-1/2” Tongue and Groove Plier 7/8”F41379 9-1/2” Tongue and Groove Plier 1-1/2”F41666 10” Tongue and Groove Plier 2”F43271 12” Tongue and Groove Plier 2-1/4”F43273 16-1/2” Tongue and Groove Plier 2-1/4”F43270 9-1/2” V-JAW Tongue and Groove Plier 1-1/2”F43272 12” V-JAW Tongue and Groove Plier 2-1/4”
• Channellock® brand• Right angle teeth grip in all directions for maximum bite and
minimum wear• Undercut tongue and groove design assures strong, can’t
slip jaw action• Permalock fastener is stronger, safer and smoother working
than the old time bolt and nut• V-JAW gives more points of contact round stock and tubing • Made in USA
BALLDRIVER® L-WRENCH SETS
Part No. Description SizesF4701 Inch set .050”, 1/16”, 5/64”,
3/32”, 7/64”, 1/8”, 9/64”, 5/32”, 3/16”, 7/32”, 1/4”, 5/16”, 3/8”
F463 Metric set 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10
• Balldriver® L-wrench sets are ideal where a variety of tool sizes are required. All set are packaged in key case. Wrenches slip easily into individually marked slots and twist to lock secure place.
• Non-sparking, soft face hammers will not mar surfaces or equipment
• Steel reinforced handles• Steel shot in head absorbs impact and
eliminates rebound
Part No. DescriptionF41357 Dead Blow Hammer 21 ozF4131 Dead Blow Hammer 42 oz
DEAD BLOW HAMMERS
ULTRAVIEW™ CLEAR GREASE GUNS
• Develops 5,000 PSI• Delivers 1 oz grease per 40 strokes• Comfortable one-hand operation• Unique bulk loader fitting doubles as air bleeder• Pistol handle designed to prevent fingers from “pinching”• High tolerance aluminum die cast head• Complete with 5” steel extension & 12” flexible hose and
coupler with ball check
• Lincoln No. 5803• Allows operator to contact flush type or
hard-to-reach hydraulic type fittings
NEEDLE ADAPTER
6-IN-1 FASTSERV SCREWDRIVER
SHOE HANDLE SCRATCH BRUSH
MAGNETIC PICK-UP TOOL
SUPER PREP™ TOWEL TOTE BOX
• Heavy-duty magnetic pick-up tool with a blue molded grip for comfort• Simply wave over ferrous material then retract the pull rod to release• Perfect for picking up metal chips and shavings around machinery and work
areas; can also be used for moving fastners in and out of bins; hundreds of other uses and applications
• Reversible shaft holds double sided phillips (#1 & #2) and slotted (3/16” & 5/16”) bits
• Can also be used as a 1/4” and 5/16” nut driver• Professional quality, high performance spunlace towel. One of the best
prepping towels for the industrial/automotive industry • Rated for use by commercial and professional painters, bright workers and
body shops as a prep wipe• Ultra strong wet or dry• Ideal for many other industries• Virtually lint-free • Solvent-resistant • Absorbs large amounts of water,
grease and oil • Will not scratch surfaces and are tear-resistant• Wiper size: 9” x 15”• Color: Blue• Tote Box Qty: 200 Wipes• Sold by Tote Box
• Stainless steel bristles• Hardwood handle• Overall length 10”• Length of trim 1-1/8”
SHOP SUPPLIES
PAGE 5We know MRO
• 12” wide mouth and 30” metal handle• Pivoting bucket locks open for hands-free disposal• Designed for use on hard and soft surfaces
Part No.F43061
Part No.F42510
LOBBY DUST PAN – BLACK MAXIROUGH® LOBBY BROOM
• Thicker diameter polycorn bristles provide superior sweeping ability• Offers liquid and chemical resistance as well as 250°F temperatures• Double sewn, hand wound construction increases durability• 30” handle with an 8” sweeping surface
ALUMINUM OXIDE RESIN FIBRE DISC
Part No. RPM DiaArborHole Grade
Discs per box
F5448 15,300 4” 5/8” 36 25F5212 15,300 4” 5/8” 60 25F5235 15,300 4” 5/8” 80 25F5875 15,300 4” 5/8” 100 25F5876 15,300 4” 5/8” 120 25F5317 13,300 4-1/2” 7/8” 36 25F5227 13,300 4-1/2” 7/8” 60 25F5717 13,300 4-1/2” 7/8” 80 25F5879 13,300 4-1/2” 7/8” 100 25F5880 13,300 4-1/2” 7/8” 120 25
• Rubber backup pad required
Part No. RPM DiaArborHole Grade
Discs per box
F5538 12,200 5” 7/8” 24 25F5389 12,200 5” 7/8” 36 25F5213 12,200 5” 7/8” 50 25F5882 12,200 5” 7/8” 80 25F5483 12,200 5” 7/8” 100 25F5883 12,200 5” 7/8” 120 25F5600 12,200 7” 7/8” 16 20F5447 8,600 7” 7/8” 24 25F5347 8,600 7” 7/8” 36 25F5641 8,600 7” 7/8” 80 25F5885 8,600 7” 7/8” 100 25
PREMIUM CERAMIC ABRASIVE FLAP DISCS
Part No. Size GritF5960 5" X 7/8" 36F5961 5" X 7/8" 40F5962 5" X 7/8" 60F5963 5" X 7/8" 80F5964 5" X 5/8-11 36F5965 5" X 5/8-11 40F5966 5" X 5/8-11 60F5967 5" X 5/8-11 80
• Self-sharpening ceramic grain and cool grinding aid for fast, aggressive cutting action on hard-to-grind materials
• Polyester backing material for longer working life • C3 Ceramic grain provides contaminate-free results; stainless steel won’t rust• Hybrid compact design (4-1/2” and 5”) - flap are compressed and
compacted at a 4° for edge and strength
• Heavy-duty bi-metal construction• Extra wide, extra thick for heavy feed and stability• Preferred by professional firefighters• For all types of machinable metal encountered in vehicle
extraction and demolition• Superior performance in sheet metal and vehicle frames
Part No. TPIL x W x T (Inches)
F6898 10 6” x 7/8” x .062”F6659 10 9” x 7/8” x .062”F61039 10 12” x 7/8” x .062”F6248 14 6” x 7/8” x .062”F6596 14 9” x 7/8”x .062”F6664 14 12” x 7/8” x .062”
FIRE & RESCUE RECIPROCATING BLADES
Morse
MECHANICS LENGTH HEX SHANK DRILLS - 1/4” QUICK RELEASE
Part No. DiameterOverall Length
F62349 1/16” 2-5/8”F62358 3/32” 3-1/4”F62356 1/8” 3-1/2”F62364 9/32” 3-13/16”F62361 5/32” 3-1/2”F62357 3/16” 3-3/4”F62363 7/32” 4”F62352 1/4” 4-1/4”F62360 5/16” 4”F62348 11/32” 4-7/32”F62359 3/8” 4-1/4”F62351 13/32” 4-1/2”F62362 7/16” 4-1/2”F62353 15/32” 4-7/8”F62350 1/2” 5”
*1/4” and smaller are 2 piece pressed and epoxy fitted
F62354
F62355
• Drill is a mechanic length with a quick release shank
• Manufactured from special Hi-Molybdenum tool steel
• 135° split point for fast penetration and accurate starting without center punch
• Gold surface treated• Specially designed for hand held drills• Quick release eases changing of cutting tools• Made in USA
- 12 - Piece Hard Case Set with Quick Release Adaptor (1/16 ”- 1/2”) - 7-Piece Soft Pouch Set (1/16” - 1/4”)
F62354F62355
ABRASIVES
CUTTING TOOLS
SHOP SUPPLIES
We know MROPAGE 6
PINSTRIPE / REMOVAL KITPart No.F81607
• Includes: -1 - Pinstripe removal tool -12 - Eraser pads (FS# F83815)• Specialty tool developed for removal of
pinstripes, adhesive, tape, adhesive, etc.• Lightweight• Max speed - 4000 RPM
AUTO & TRUCK — RAIN CAPS HEAVY-DUTY
Part No.PipeSize
F81603 1-1/2”F81011 1-3/4”F8491 2”F82257 2-1/2”
Part No.PipeSize
F81461 3”F84636 3-1/2”F81802 4”F8769 5”
• Heavy-duty welded lid• Full exhaust opening • Single bolt mounting• Baked on aluminum
powder coat finish
ADAPTERS — STEEL SWIVEL
FEMALE 37° JIC SWIVEL TO MALE PIPE
Part No.TubeO.D.
MalePipe Thread
EquivalentEaton No.
HexC L
F75707 1/4” 1/8” 9/16” 1.13”F74850 5/16” 1/8” 11/16” 1.17”F7360 1/4” 1/4” 9100X4X4 9/16” 1.130”F7859 5/16” 1/4” 9100X5X4 11/16” 1.170”F7808 3/8” 1/4” 9100X6X4 11/16” 1.290”F74694 3/8” 3/8” 9100X6X6 11/16” 1.290”F71935 1/2” 3/8” 9100X8X6 7/8” 1.430”F77630 1/2” 1/2” 9100X8X8 7/8” 1.610”F7820 5/8” 1/2” 9100X10X8 1” 1.600”F73319 3/4” 1/2” 9100X12X8 1-1/8” 1.650”F76387 3/4” 3/4” 9100X12X12 1-1/8” 1.650”F73102 1” 1” 9100X16X16 1-3/8” 1.940”
JIC 37° SWIVEL NUT 45° ELBOW
Part No.Tube O.D.
Hex C D M N
Across Flats
EquivalentEaton No.
F76715 1/4” 9/16” .172” .72” .94” 7/16” C5356X4F75344 5/16” 5/8” .234” .77” 1.00” 9/16” TF5356X5F76103 3/8” 11/16” .297” .83” 1.12” 9/16” C5356X6F74648 1/2” 7/8” .391” .98” 1.28” 3/4” C5356X8F75565 5/8” 1” .484” 1.11” 1.44” 7/8” C5356X10F76294 3/4” 1-1/4” .609” 1.28” 1.50” 1-1/6” C5356X12F71862 7/8” 1-3/8” .718” 1.39” 1.62” 1-5/16” C5356X14F76022 1” 1-1/2” .845” 1.47” 1.75” 1-5/16” C5356X16F71152 1-1/4” 2” 1.078” 1.59” 2.03” 1-5/8” TF5356X20
• Typical Application: Pressure-hydraulic systems
• Pressure: Up to 10,000 PSI depending on size
• Sealing Method: Metal to metal, 30° cone-NPSM thread on swivel end
• Material: Carbon steel, AISI/SAE 12L14
• Plating: Zinc, yellow dichromate finish
C
L
D
M N
C
• Hex shank reamers allow for tool to be used with sockets• Specifically designed for reaming structural steel plates commonly found in truck
frames, rail cars, bridges and large vessels• For use only to enlarge previously drilled holes• M7 steel• Made in USA
HEX SHANK SPIRAL FLUTE CONSTRUCTION REAMERS
Part No. DiameterPoint Diameter
MinimumStarting Hole Size
Overall Length
Hex Shank WrenchSize
F62428 9/16” .343” 7/16” 5-7/8” 1-1/16”F62425 5/8” .343” 7/16” 6-3/8” 1-1/16”F62421 11/16” .375” 15/32” 6-3/8” 1-1/16”F62423 13/16” .468” 35/64” 6-7/8” 1-1/4”F62424 15/16” .585” 5/8” 6-7/8” 1-7/16”F62420 1-1/16” .807” 7/8” 6-7/8” 1-5/8”F62422 1-3/16” .719” 1” 6-7/8” 1-13/16”
Part No.F03131
FUEL / VACUUM LINE DISPENSER
• An easy to use dispenser for fuel and vacuum hoses• Holds reels up to 6-1/2” in diameter• Grommets on front hold hose in place, ready for dispensing• Hinged top helps keep hoses clean• Dimensions: 12” H x 19-1/2” W x 14” D Nominal• Designed to be able to be placed on top of a 4-drawer rack system• Ruler is painted on lid for easy measuring of hose lengths
Side 1
Side 2• Over All Dimensions: 36”H x 24”W x 34”D• Ships in 5 cartons. Shipping weight is 180 lbs.
MOBILE CART CABINET/BIN/DRAWER
MOBILE CART CABINET
Part No. ComponentsF03129 Mobile Cart Cabinet/Bin/DrawerF01104 Storage Bin 12 CompartmentF01091 Aerosol CabinetF01100 (2) Storage Cabinets 6 DrawerF03123 Mobile Cart Base
• Over All Dimensions: 32”H x 24”W x 34”D• Ships in 3 cartons. Shipping weight is 159 lbs.
Part No. ComponentsF03127 Mobile Cart 80 BinF01112 (2) Storage Bins 40 CompartmentF03123 Mobile Cart Base
FLUID POWER
ASSORTMENTS
AUTOMOTIVE
CUTTING TOOLS
PAGE 7We know MRO
3/8” x 4”F13148 (10)
3/8” x 1-1/2””F15193 (20)
5/16” x 1”F113803 (25)
1/4” x 1-1/2””F16665 (25)
3/8” x 3”F116548 (10)
5/16” x 3”F11378 (25)
1/4” x 3”F11658 (25)
1/4” x 1”F17538 (25)
3/8” x 2-1/2””F111405 (20)
5/16” x 2”F120037 (25)
1/4” x 2-1/2””F12553 (25)
3/8” x 2”F112981 (20)
5/16” x 1-1/2””F16263 (25)
1/4” x 2”F15054 (25)
SCREWS — LAG ZINC-PLATED305 PIECES
SUBARU BODY CLIP ASSORTMENT170 PIECES
Part No.F03339
Part No.F012550
Part No.F03241
Part No.F03169
SCREWS — THUMB 150 PIECES
ANCHORS — LAG SHIELD120 PIECES
5/16”-18 x 3/4”F199 (5)
5/16”-18 x 1/2”F114415 (5)
1/4”-20 x 1-1/4”F119652 (5)
1/4”-20 x 3/4”F116307 (10)
1/4”-20 x 1-1/2””F113684 (5)
10-24 x 1/2”F117968 (10)
6-32 x 1/2”F16717 (10)
1/4”-20 x 2”F114924 (5)
10-24 x 3/4”F13230 (10)
6-32 x 3/4”F116127 (10)
1/4”-20 x 2-1/2””F12006 (5)
5/16”-18 x 1-1/2””F114092 (5)
10-24 x 1”F120013 (10)
8-32 x 3/4”F17071 (10)
1/4”-20 x 3”F110874 (5)
5/16”-18 x 1”F16285 (5)
5/16”-18 x 1-1/4”F18326 (5)
5/16”-18 x 2”F13817 (5)
8-32 x 1”F19028 (10)
1/4”-20 x 1”F17146 (5)
1/4”-20 x 1/2”F118038 (10)
1/4” x 1”F119578 (25)
1/4” x 1-1/2”F11754 (25)
5/16” x 1-1/4”F119922 (25)
5/16” x 1-3/4”F1463 (25)
3/8” x 1-3/4”F117128 (10)
3/8” x 2-1/2”F113812 (10)
NEW PRODUCT
F85431 (10)
F85683 (10)
F84226 (10)
F85426 (10)
F85436 (10)
F8135 (10)
F85427 (10)
F85713 (10)
F84330 (5)
F85685 (10)
F85714 (10)
F82973 (5)
F85712 (10)
F85684 (10)
F85160 (10)
F85686 (10)
F85425 (10)F81105 (10)
ASSORTMENTS
Ed. 15 Vol. 8
Custom Designed
to organize your suppliesStorage Systems
FastServ can custom design a storage system to fit your needs. In addition, our planned inventory control systems help with parts organization, saving both time and money.