eduard JAS-39 Gripen S.A. · 2013. 11. 1. · jas-39 gripen s.a. fe656 eduard 1/4 fe 656 original...
Transcript of eduard JAS-39 Gripen S.A. · 2013. 11. 1. · jas-39 gripen s.a. fe656 eduard 1/4 fe 656 original...
1/48 scale detail set for KITTY HAWK •sada detailů pro model 1/48 KITTY HAWK
JAS-39 Gripen S.A.
FE656
eduard
1/4 FE 656
ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍ
FILLTMELIT
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM
1 COLORED ETCHED PARTSLEPTANÉ BAREVNÉ DÍLY
film
3
1
2
26
24
5
5
23
E35front
8
9E15, E16, E17
E15, E16, E17
10
4
6
21 22
DANGER
1/48 FE 656 + 49 656 JAS-39 Gripen
© EDUARD 2013 Made in Czech Republic
6
1 23
4
5 5 68 9
10 11 12
13
14151617181920
7
2122
23
27
24
25 26
32
28 29 3028 28 31 31 31 31 31
33
3435
36 36 36
37
38
39
2/4 FE 656
C13, C16
13
C335
16
?
15
14
20
26
19
34
early
late
18 17
38
39
12
film
11
early
late
?C11
29
C21 C22
30
PE6
C2
C1
37
7
27
do not use kit parts C7 and C8
3/4 FE 656
I14 I15
36
36
25
32
31
31
B31
33
31
31
new position
GP2
28 PE11
4/4
© EDUARD M.A. 2013 Made in Czech Republicwww.eduard.com
FE 656
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na části dílů, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will be permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne až po přimáčknutí, před přimáčknutím lze dílem opatrně manipulovat.
PARTS WITH GLUE DÍLY OPATŘENÉ LEPIDLEM