ECSU Fun 4 NASC
Transcript of ECSU Fun 4 NASC
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 1/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 1
DETAILED TEACHING SYLLABUS
FUNCTION 4 CONTROLLING THE OPERATION OF THE SHIP AND CARE
FOR PERSONS ON BOARD AT THE MANAGEMENT LEVEL
Name of Course : Combined Chief and Second Engineer 3000 kW or more
Unlimited Voyage
Course Code : ECSU
Subject : Controlling the Operation of the Ship and Care for Persons
on board (NASC)
Instructional HoursLecture : 75 hoursPractical : 0 hours
Tutorials : 25 hours
Total Contact Hours : 100 hours
Self Learning : 70 hours
Total Hours : 170 hours
Entry Requirements : Watchkeeping Engineer 750 kW or more
Subject Aims
The module provides an understanding of the principles that maintain the stability of ocean going
ships under various conditions of cargo loading and seaway.
The module also provides an understanding of the design and constructional aspects of ships
with reference to effective maintenance and environment protection.
Teaching Methods
The course shall be conducted in a combination of classroom lectures and self-learning.
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 2/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 2
Assessment Methods
Lecturers’ Class Assessments : 50%
Final Exam : 50%
Recommended Texts
1. E.C. Tupper (2004) Introduction to Naval Architecture, Butterworth Heinemann, ISBN:0-7506-6554-8.
2. E.A. Stokoe (2003) Reed’s Naval Architecture for Marine Engineer. Reed’s Marine
Engineering Series
3. D.J. Eyres (2001) .Ship Construction 5th. Edition. Butterworth-Heinemann
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 3/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 3
Table of Specifications
Topics Weightage %
Total K U A I
A Ship Types and Terms 0 2 0 0 2
B Stresses in Ship Structures 0 1 1 0 2
C Ship Construction 0 10 10 0 20
D Ship Dynamics 0 1 1 0 2
E Hydrostatics 0 2 1 0 3
F Displacement, TPC, Coefficients of Form 1 1 1 0 3
GAreas and Volumes of ship shapes, 1
st and
2nd
M0 6 2 2 10
H Centers of Gravity 0 2 1 0 3
I Transverse Stability 0 4 3 0 7
J Trim 0 2 2 0 4
KStability during dry-docking and stability
during grounding0 2 0 0 2
L Resistance and Fuel Consumption 0 3 2 0 5
M Propeller and Power 0 3 2 0 5
N Rudders 0 1 1 0 2
OEffect of flooding on transverse stability
and trim0 3 2 0 5
P Countermeasures to be taken 0 1 1 0 2
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 4/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 4
QIMO recommendations concerning ship
stability0 2 1 0 3
R Methods and Aids to prevent pollution ofthe environment y ships
0 14 1 0 15
S Fire-fighting equipment 0 2 1 0 3
T Life saving appliances 0 2 0 0 2
Total 1 64 33 2 100
Note 1:
The Letters K, U, A, and I in the table of specifications denote the Knowledge, Understanding
(Comprehension), Application and Integration (Higher than Application) levels of Bloom's
taxonomy in the cognitive domain.
Note 2:
In the following detailed syllabus, all objectives should be understood to be prefixed by the
words "At the end of the lecture, the learner should be able to .." In the second column,
L: P: T: SL denotes the number of instructional hours devoted to lectures, practicals, tutorials
and self learning respectively.
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 5/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 5
Learning Objectives L: P: T: SL
A.
Ship Types and Terms
1.0 General Learning Objective:
Understand the fundamental principles of ship types and the terms
used with relations to the ship tonnage and load line rules
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.1) 1.1 Explain about the various ship types: passenger ships, cargo liners, oil
tankers, bulk carriers, container ships, roll-on/roll-off vessels, liquefied
gas carriers, chemical carriers.
1.2
Describe the terms used in the measurement of ships: after perpendicular, forward perpendicular, length overall, length between
perpendiculars, breadth extreme, breadth moulded, depth extreme,
depth moulded, draught extreme, draught moulded, freeboard, camber,sheer, rise of floor, bilge radius, tumble home, flare, stem rake, keel
rake, entrance, run, displacement, lightweight, deadweight.
1.3 Explain the tonnage rules.1.4 Explain the load line rules.
2 : 0 : 0: 2
B. Stresses in Ship Structures
2.0 General Learning Objective:
Understand the terms used in describing the stresses subjected to
various parts of ship structures, including when ship subjected to dry-docking and grounding
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.2) 2.1 Describe the terms used to describe stresses in ship structures:
longitudinal bending, still water bending, load diagram, shear force
diagram, bending moment diagram, hogging, sagging, wave bending,
and transverse bending.2.2 Explain the effect of stresses on ships’ structures while at dry-dock,
floating dock and grounding.
2.3 Explain the condition of pounding and panting, while the ship sails at
sea.
4 : 0 : 0: 2
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 6/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 6
C. Ship Construction
3.0 General Learning Objective:
Understand the terms used in describing the various parts andcomponents of a ship and how these could help in the overall ship’sstrength in encountering the external forces
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.3)
3.1 Explain the terms used to describe structural members: keel, bilge keel,duct keel, bottom plating, double bottom, tank top, girder, centre
girder, side girder, floor, side frame, shell plating, deck plating,
flanges, margin plate, longitudinal, intercostals, stiffener, web frame,
bulkhead, collision bulkhead, panting stringer, stringer, pillars,garboard strake, sheer strake.
3.2
Describe the construction of the double bottom tanks.3.3 Explain the safety features for duct keels used for ship.3.4 Discuss on the construction details of the forward and after peak
structures.
3.5 Describe in detail the anchor cable termination.3.6 Explain the different types of framing system on ships which include
longitudinal, transverse and combined types of frame.
3.7 Explain the various types and functions of decks.
3.8 Explain the various types and functions of ship’s hatch covers.3.9 Explain the function of bulwarks.
3.10 Explain the function of deep frames.
3.11
Explain the design consideration for discontinuities in the vesselstructure.
3.12 Describe the roles and function of bilge keel and its consideration to
stabilize the ship when encountering rough sea.
3.13 Describe the purpose of having strakes for the hull of the ship.3.14 Explain the purpose of having fittings fixed through the hull.
3.15 Discuss how the Engine, deck machinery and stabilizer being
supported and strength in order to overcome the vibration issues.3.16 Identify the location of the bulkheads and its effect towards floodable
length.
3.17 Explain how the positioning of it is important.
3.18
Explain how well is it constructed.3.19 Comprehend the effect of the bulkhead integrity when it is pierced
during normal operation. Maintenance work necessary to ensure its
strength not compromise.3.20 Identify the rudder and its support arrangements.
3.21 Describe the stern frame and its structure.
3.22 Design criteria for specialized ships and how it supports the ship’s
24: 0: 0: 6
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 7/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 7
structure and stability.3.23 Discuss structural make-up of the bulkhead and accommodation doors
and its ability for fire protection.
3.24 Comprehend the ship’s general arrangement drawing and identify
safety equipments and gadgets installed at various parts of the ship.3.25 Explain the shell expansion and its relations with regards to ship
construction, and to know the actual amount of steel required.3.26 Prepare deck plan for a ship when loaded and ballast.
3.27 Create a mid-ship section drawing of a vessel and understand the
stresses subjected to it while at still and wave bending forces.
D. Ship Dynamics
4.0 General Learning Objective:
Understand the ship dynamics and its relation to ship motions andways to improve it and creating a vibration-free ship
Specific Learning Objectives: (IMO 7.02,2011: F4/ 4.1.1.4)4.1 Determine the effect of ship motions due to the following forces which
resulted in: Rolling – period of roll and isochronous rolling Pitching
Heaving
4.2 Determine how the attachment of bilge keels help to improve ship’s
stability and reduce the effect of rolling.
4.3
Identify where fin stabilizers are placed on the ship’s hull and describeits function in providing stability to the ship as travel through the
ocean.4.4 Discuss how the passive and active anti-roll tanks works in order to
dampen ship’s motion and kept the ship in a stable condition.
4.5 Explain the sources of vibration on a ship and how it can beeliminated, to provide a vibration free ship.
2 : 0 : 0: 2
E. Hydrostatics
5.0 General Learning Objective:
Understand the hydrostatics forces acting on a ship or any other
floating bodies
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.5)
5.1 Explain density of liquids and how it provides thrust and buoyancy toship.
3 : 0 : 0: 3
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 8/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 8
5.2 Describe how different water relative density could affect ship’sstability.
5.3 Explain the different types of liquids at varying depth exerting pressure
on floating objects and ships.
5.4
Explain the load acting on an immersed plane.5.5 Identify location of centre of pressure acting floating bodies.
5.6 Explain load diagram acting on ship’s floating on water. 5.7 Identify the shearing force acting on bulkhead stiffeners
F. Displacement, TPC & Coefficients of Form
6.0 General Learning Objective:
Understand the hydrostatics forces acting on a ship or any other
floating bodies.
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.6) 6.1 Discuss on Archimedes' principle and its relationship with buoyancy,
displacement and up-thrust.
6.2 Discuss ship’s displacement during light-ship as well as when ship isfully loaded and during ballast condition.
6.3 Explain on Tonne Per Centimetre immersion (TPC) of a ship.
6.4 Explain how block coefficient effect the ship’s displacement.
6.5 Explain how prismatic coefficient will affect ship’s maneuverability.6.6 Explain how midship coefficient affects the jumbo sizing the ship.
6.7
Explain how water plane area coefficient will affect ship’s motion. 6.8 Explain the wetted surface area in relation to the draft of the ship.6.9 Explain about similar figures between ship shape and its model in
justifying stability, motion and propulsion resistance.
6.10 Explain the influence of hull form on coefficients with relation tocarrying capacity or volume achievable in relation to the ship’s speed.
2 : 0 : 4: 3
G. Areas and Volumes of Ship Shapes, First and Second Moments
7.0 General Learning Objective:
Understand the ship shapes in identifying the areas and volumes ofcargo spaces and its relationship with calculating using First and
Second Moments in order to find the vertical centre of buoyancy and
longitudinal centre of buoyancy of the ship
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.7)
7.1 Explain how Simpson's 1st and 2nd Rules may be used to find areas
6 : 0 : 4: 5
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 9/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 9
and volumes of ship shapes, hulls and tanks7.2 Utilize the application of Simpson's rules to calculate areas and
volumes of ship’s water plane areas, hulls and tanks.
7.3 Calculate the common areas such as water planes, sections and
bulkheads.7.4 Explain the immersed volume of hull by sections and water planes.
7.5 Explain the Simpson's 1st and 2nd Rules for 1st moments and infinding centroids.
7.6 Utilize the application of Simpson's Rules to find centroids of
homogeneous objects.
7.7 Calculate to find the centroids of common areas such as, water planes,sections and bulkheads.
7.8 Calculate the Vertical Centre of Buoyancy, VCB; Longitudinal Centre
of Buoyancy, LCB of the ship.
7.9 Explain the Simpson's 1st and 2nd Rules for 2nd moments of area.
7.10
Utilize the application of Simpson's Rules to find 2nd moments ofarea.
7.11 Calculate to find Transverse moment of inertia, IT; Longitudinalmoment of inertia, IL of the homogenous ship shape or floating objects.
H. Centers of Gravity
8.0 General Learning Objective:
Understand the effect of shifting, loading, removal or transfer of
masses and its effect on ship’s longitudinal and vertical centre of
gravity
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.8) 8.1 Explain the longitudinal centre of gravity of a ship.
8.2 Explain the vertical centre of gravity of a ship which could either be
stable, unstable or neutral.8.3 Describe the shift in centre of gravity of the ship due to the addition,
removal or transfer of masses.
8.4 Describe the effect of a suspended mass when loading or unloading
cargoes.
2 : 0 : 2: 3
I.
Transverse Stability
9.0 General Learning Objective:
Understand the factors that affect transverse stability of a ship 5 : 0 : 3: 7
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 10/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 10
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.9) 9.1 Explain how vertical centre of buoyancy could be achieved.
9.2 Use hydrostatic tables in order to understand the condition of the ships
tank capacity.
9.3
Identify the transverse metacentric height, GM of a ship. Explainwhether it is classified as stiff or tender if GM is positive.
9.4 Sketch a midship cross-section of a ship inclined to a small angle,showing the position of G, B and righting lever, GZ.
9.5 Determine how the righting lever is calculated to determine ship’s
stability at small angles of heel.
9.6 Explain the metacentric diagram of a ship.9.7 Explain how using an inclining experiment of a geosim model, the
centre of ship’s centre of gravity could be achieved.
9.8 Explain how the free surface effect could endanger ship’s stability
9.9 Explain the effect of ship’s stability at large angles of heel.
9.10
Determine the cross curves of stability, using KN Tables to makecorrections before deriving the final GM of the vessel.
9.11 Using curve of static stability to determine the condition of the ship.9.12 Explain dynamical stability in a vessel which [provide an upsetting
moments vary as the ship heels with an initial negative GM.
9.13 Discuss the ship’s stability at varying small angles of loll, and how
ship’s list can be improved by securing all moving items on the shipwhile encountering rough seas.
J. Trim
10.0 General Learning Objective:
Understand the principle of trim and its effect on draughts
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.10) 10.1 Explain the centre of flotation
10.2 Explain the mean draught.10.3 Demonstrate where the longitudinal metacentre (ML) a ship.
10.4 Explain the change in draughts due to added masses.
10.5 Explain the Moment to Change Trim 1 centimeter.
10.6 Explain the change in draughts due to a change in density.10.7 Explain the change in trim due to change in density.
3 : 0 : 3: 4
K. Stability during Dry-docking and stability during grounding
11.0 General Learning Objective:
Understand the principle of trim and its effect on draughts whiledocking the vessel or grounding situations
2 : 0 : 1: 3
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 11/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 11
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.11) 11.1 Explain the procedures for dry-docking, the forces acting on the ship to
ensure stability when docking.
11.2
Explain the procedures for dry-docking, the forces acting on the ship toensure stability on grounding.
L. Resistance and Fuel Consumption
12.0 General Learning Objective:
Understand the principle of resistance on the vessel’s hull and its effect
on fuel consumption and power
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.12) 12.1 Explain what is meant by frictional resistance of a ship.
12.2 Explain Reynolds’ number.
12.3 Describe the components of residuary resistance.12.4 Use Froude’s number to determine the residuary resistance of similar
ships.
12.5 Explain why speed length ratio is used to determine whether the ship isslow or fast.
12.6 Determine how to get effective power of the vessel once total
resistance and speed data can be calculated.
12.7 Explain what Admiralty coefficient is.
12.8
Explain about the relationship between fuel coefficient and fuelconsumption.
3 : 0 : 3: 3
M. Propellers and Power
13.0 General Learning Objective:
Understand the principle of propellers and the various power involved
in propelling ships
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.13)
13.1
Explain the terms used in the calculation of propulsion coefficients:diameter, pitch, pitch ratio, theoretical speed, apparent slip, wake
fraction, real slip, projected area, developed area, blade area ratio, anddisc area ratio.
13.2 Explain the terms used in the calculation of power factors: thrust power,
shaft power, delivered power, thrust deduction factor, effective power,and quasi-propulsive coefficient.
3 : 0 : 3: 3
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 12/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 12
13.3 Discuss the measurement of pitch.13.4 Discuss how cavitation occurs on propeller.
13.5 Describe about ship trials – speed measurements
N. Rudders
14.0 General Learning Objective:
Understand the principle forces on the rudder and its functioning
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.1.13)14.1 Explain the following with respect to conventional rudders:
14.1.1 Force on a rudder.
14.1.2 Torque on a rudder stock.
14.1.3
Angle of heel due to force on rudder.14.1.4 Angle of heel when turning.
2 : 0 : 2: 2
O. Effect of flooding on transverse stability and trim
15.0 General Learning Objective:
Understand the effects on trim and stability of the vessel in the eventof hull damage and flooding of compartments
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.2) 15.1 Describe the effects of flooding on transverse stability and trim for the
following conditions:
15.1.1 Grounding, damage and bilging.
15.1.2 Bilging amidships compartment.15.1.3 Bilging of side compartment.
15.1.4 Bilging end compartment.
15.1.5 Effect of bilging on stability (Draft, Trim, List and GM) – bylost buoyancy method and by added mass method.
1 : 0 : 0: 2
P.
Countermeasures to be taken during flooding
16.0 General Learning Objective:
Understand the counter measures to be taken
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.2)
1 : 0 : 0: 2
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 13/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 13
16.1 Explain the countermeasures to be taken in the event of flooding ofcompartments
16.2 Explain that countermeasures during cross flooding of compartments
will be according to details in damage control plan.
Q. IMO recommendations concerning ship stability
17.0 General Learning Objective:
Know the recommendations of IMO with regards to stability of ships
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.1.3) 17.1 Recognize the IMO recommendations concerning ship stability
17.1.1 International Code of Intact Stability,2008 (2008 IS code)
17.1.2 Damage control plan
17.1.3
Damage control booklet17.1.4 Use of on-board computers
17.1.5 Shore based emergency response system
0 : 0 : 0: 3
R. Methods and Aids to prevent pollution of the environment y ships
18.0 General Learning Objective:
Understand the prevention measures taken to prevent environment pollution caused by ships
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.2.8) 18.1
List the conventions related to Marine Pollution.
18.2 Identify the sources of Marine pollution:
18.2.1 Oil.
18.2.2 Noxious liquid substances carried in bulk.18.2.3 Harmful substances carried by sea in packaged form.
18.2.4 Sewage.
18.2.5 Garbage.18.2.6 Air.
18.2.7 Ballast water.
18.2.8
Anti-fouling paints.18.2.9 Noise.
18.3 Explain the effects of marine oil spills.
18.4 Recognize Regulations for prevention of oil pollution as per Annex I
of MARPOL 73/78 for the following:18.4.1 Tanks for oil residues (Sludge).
18.4.2 Oily water separator and oil filtering equipment and oil content
2 : 0 : 0: 5
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 14/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 14
monitoring.18.4.3 Standard discharge connection.
18.4.4 Control of oil discharge – discharge in special areas and outside
special areas.
18.4.5
Oil record book.18.4.6 Requirement for oil tankers.
18.4.7 Double hull and double bottom tank.18.4.8 Intact stability requirements.
18.4.9 Subdivision and damage stability.
18.4.10 Slop tanks.
18.4.11 Pumping, piping and discharge arrangements.18.4.12 Oil monitoring and control system.
18.4.13 Requirements for crude oil washing.
18.4.14 Control of discharge of oil from oil tankers - Discharge
outside special areas and Discharge in special areas.
18.4.15
Shipboard oil pollution emergency plan.18.4.16 Reception facilities.18.4.17 Concept of Integrated Bilge Water Treatment System (IBTS).
18.5 Recognize Regulations for control of pollution from Noxious liquid
substances carried in bulk as per Annex II of MARPOL 73/78.
18.5.1 Identify The International Code for the Construction and
Equipment of Ships Carrying Dangerous Chemicals in Bulk(IBC Code), the Code for the Construction and Equipment of
Ships Carrying Dangerous Chemicals in Bulk (BCH Code) and
the Code for the Construction and Equipment of ShipsCarrying Liquefied Gases in Bulk (IGC Code).
18.6
Recognize Regulations for the Prevention of Pollution by Harmfulsubstances carried by sea in packaged form as per Annex III of
MARPOL 73/78.18.7 Recognize Requirements covering the carriage of dangerous goods by
sea as per Chapter VII of the SOLAS Convention
18.7.1 Carriage of dangerous goods in packaged form and IMDGCode.
18.7.2 Carriage of dangerous goods in solid form in bulk.
18.8 Recognize Regulations for the Prevention of Pollution by Sewage fromShips as per Annex IV of MARPOL 73/78.
18.8.1 Harmful effects of sewage to the marine environment.
18.8.2
Sewage treatment plant; system to comminute and disinfect thesewag; and a holding tank.
18.8.3 Standard discharge connections.
18.8.4 Discharge of sewage.
18.8.5 Reception facilities.18.9
Recognize Regulations for the Prevention of Pollution by Garbage
from Ships as per Annex V of MARPOL 73/78.
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 15/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 15
18.9.1 Placards, garbage management plans and garbage recordkeeping.
18.9.2 Shipboard incinerators.
18.9.3 Disposal of garbage outside special areas.
18.9.4
Disposal of garbage within special areas.18.9.5 Reception facilities.
18.10 Recognize Regulations for the Prevention of Air Pollution as perAnnex VI of MARPOL 73/78.
18.1.1 Explain that use of ozone depleting substances prohibited on
ships. Use of HCFCs permitted till 1st January 2020.
18.1.2 Explain that Sculpture content of any fuel oil used on boardships shall not exceed 4.5% m/m and a progressive reduction in
sulphur initially to 3.50% effective from 1 January 2012; then
progressively to 0.50 %, effective from 1 January 2020, subject
to a feasibility review to be completed no later than 2018.
18.1.3
Explain that the sculpture content limits applicable in SulphurEmission Control Areas is 1.00% and will be further reducedto 0.10 %, effective from 1 January 2015 or an exhaust gascleaning system, approved by the Administration.
18.1.4 Explain that Bunker delivery notes and representative sample
are to be retained on board for a certain period of time.
18.1.5 Recognize the NOX technical file on board ship as per NOxTechnical Code 2008 for all marine diesel engines with a
power output of 130 kW or more.
18.1.6 Recognize requirements of Vapor collection system for tankersfor control of volatile organic compounds.
18.1.7
Explain the shipboard incineration and guidelines for use ofincinerator.
18.11 Recognize the significance of International Convention for the Controland Management of Ship’s Ballast Water and Sediments with respect
to following:
18.11.1 Ballast water treatment or exchange, depending upon year of build and size of ship.
18.11.2 Ballast Water Management Plan.
18.11.3 Ballast Water Record Book.18.12 All ships using ballast water exchange should whenever possible,
conduct ballast water exchange at least 200 nautical miles from the
nearest land and in water at least 200 meters in depth.18.13 Explain requirements with respect to Anti-fouling paints
18.13.1 Explain that Ships could no longer be coated with TBT-based
antifoulings and those vessels coated with it have them
removed have a barrier coating to prevent their leaching.18.14
Recognize requirements with respect to Noise by IMO Assembly
resolution A468 (XII) – Code on noise levels on board ships.
8/18/2019 ECSU Fun 4 NASC
http://slidepdf.com/reader/full/ecsu-fun-4-nasc 16/16
ALAM/Post Sea/ECSU/Function 4/Controlling Operation of Ship & care for persons (NASC) 16
S. Fire-fighting equipment
19.0 General Learning Objective:
Understand the shipboard fire prevention measures, aids and methods
for detection and extinction of fires
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.4.2) 19.1 Explain the following with respect to Firefighting equipment on board:
19.1.1 Construction, installation and operation of fixed fire fighting
installations..1.2 Construction, installation and operation of portable and semi portable
firefighting equipment.
4 : 0 : 0: 5
T.
Life Saving Appliances
20.0 General Learning Objective:
Understand the functions and usage of shipboard life saving appliances
Specific Learning Objectives: (IMO 7.02, 2011: F4/ 4.4.3) 20.1 Explain the following with respect to the shipboard Life
saving appliances:
20.1.1 Construction, installation and operation of life savingequipment.
20.1.2
Tests, procedures and maintenance necessary to ensure correctand safe operation of life-saving and other safety equipment.
20.1.3
Maintenance of water tight doors.
4 : 0 : 0: 5