Drive Test 3G
-
Upload
deddy-setiadi -
Category
Documents
-
view
1.729 -
download
22
Transcript of Drive Test 3G
Drive Test 3GBy Rendra
UMTS merupakan suatu revolusi dari GSM yang mendukung kemampuan generasi ketiga (3G).
Terdapat dua mode yang digunakan dalam WCDMA dimana yang pertama menggunakan FDD (Frequency Division Duplex) dan kedua dengan menggunakan TDD (Time Division Duplex). FDD dikembangkan di Eropa dan Amerika sedangkan TDD dikembangkan di Asia(indonesia)
Pada WCDMA FDD, digunakan sepasang frekuensi pembawa 5 MHz pada uplink dan downlink, namun untuk TDD hanya berlaku satu frekuency carier sebesar 5 MHz
Introduce
Architecture
UMTS Architecture UE (User Equipment)
◦ Merupakan komponen utama dari UMTS network yang bertugas berinteraksi dengan user/customer yang dapat melakukan panggilan dan akses data
Node B◦ Perangkat yang bertugas sebagai penghubung
antara UE dengan RNC RNC=Radio Network Controller
◦ Sebuah element dari Radio Network Subsystem yang bertugas mengontrol node B yang terhubung. Dan juga mengenkripsi data yang diterima dari node B untuk dapat dikirimkan ke MSC
MSC◦ Elemen dari UMTS network yang bertugas
mengatur proses switching telephony. GMSC (Gateway Mobile Switching Centre)
◦ Gate way dari circuit switch proses yang berhubungan langsung dengan network lainnya
SGSN (service GPRS support node)◦ Sebuah element yang bertanggung jawab
terhadap akses GPRS pada jaringan UMTS GGSN (Gateway GPRS Support Node)
◦ Gateway dari SGSN yang bertanggung jawab untuk menghubungkan dengan network lainnya
Con’t…
Interface pada UMTS
Ada empat interface yang digunakan dalam UMTS yaitu :◦ Uu : untuk menghubungkan UE dan Node B◦ Iub : untuk menghubungkan Node B ke RNC◦ Iur : untuk kontrol dan manajemen data exchange
antar RNC◦ Iu : untuk menghubungkan RNC ke GSM phasa 2+
(MSC, VLR,SGSN).
Interface pada UMTS
UMTS beroperasi pada band frequency 2100 MHz Satu operator mempunyai 5 MHz sebagai
frekuensi carier. Karena indonesia menganut system TDD maka frekuensi uplink downlink nya berada dalam satu kanal frekuency
Frequency
Berikut macam-macam Handover pada UMTS Network◦ Softer Handover
Proses perpindahan serving cell dalam kondisi MS dedicated dari sector yang satu ke sector yang lain di node B yang sama
◦ Soft Handover Proses perpindahan serving cell dalam kondisi MS dedicated
dari node B yang satu ke node B yang lain dalam satu RNC◦ Hard handover
Proses handover yang terjadi antar RNC◦ Interfrequency handover
Handover yang terjadi ketika MS berpindah dari frequency yang satu ke yang lain
◦ Inter System Handover(ISHO) Handover yang terjadi ketika MS berpindah MS(misal dari
WCDMA ke GSM)
Handover
Handover
Cell Global Identity Cell Global Identity is a unix code that used for identity of a cell.
- MCC : Mobile Country Code
- MNC : Mobile Network Code
- LAC : Location Area Code
- CI : Cell Identity
Cell Global Identity Mobile country code
Cell Global Identity Mobile Network Code
Cell Global Identity Location Area Code
Cell Global Identity Cell Identity
Singkatan dari Common Pilot Channel Receive Signal Code Power
Merupakan level signal dari node B yang terukur di MS
Nilai nya berkisar antara:◦ 0 -40 dbm◦ -41 -60 dbm◦ -61 -85 dbm◦ -86 -92 dbm◦ -92 -120 dbm
Measurement WCDMACpich RSCP
CPICH Ec/No is the ratio of the received energy per PN chip for the CPICH to the total received power spectral density at the UE antenna connector. The reporting range for CPICH Ec/No is -24 dB to 0 dB (0 to 49).
Measurement WCDMACpich Ec/No
CPICH Ec/No Reported Value
Measured Quantity Value Unit
0 CPICH Ec/No < -24 dB
1 -24 </= CPICH Ec/No < -23.5 dB
... ... ...
48 -0.5 </= CPICH Ec/No < 0 dB
49 0 </= CPICH Ec/No dB
Phone idle mode
Idle mode
NCell
NCell
Serving Cell Reports to HP K800i
cpich RSCP + cpich Ec/No Serving cell
Phone dedicated mode
Dedicated Mode Dedicated Mode
NCell
NCell
Call processing
Call processing• Call attempt
Call attempt adalah panggilan yang bert ujuan untuk meminta kanal node B
• Call attempt retry◦ Call attempt retry adalah panggilan yang diulang untuk
meminta kanal pada node B.• Block call
◦ Block call adalah panggilan yang berakhir secara tidak normal ketika melakukan call setup. Block call terjadi akibat kanal yang penuh.
• Call setup◦ Call setup adalah panggilan (signaling) yang telah
dibangun antara pihak pemanggil dengan pihak penerima panggilan (callsetup berbentuk nada panggil).
• .
Call processing
• Call establish◦ Call establish adalah pembicaraan yang telah
terbangun antara pihak penelpon dengan pihak penerima panggilan.
• Drop call Drop call adalah panggilan yang berakhir secara
tidak normal setelah melakukan proses call establish. Drop call dapat didefinisikan sebagai pemutusan hubungan pada saat pembicaraan antara pihak pemanggil dan penerima sedang berlangsung.
• Call end Call end adalah pembicaraan yang telah berakhir
secara normal antara pihak pemanggil dengan pihak penerima panggilan.
Istilah-istilah
AS = Active site = cell yang diduduki oleh MS pada saat dedicated mode
SC = Serving Cell = cell yang diduduki oleh MS pada saat idle mode
MN = monitoring Neighbour = cell tetangga yang memungkinkan untuk handover ketika levelnya lebih baik dari serving cell
DN = Detect Neighbour = Cell tetangga yang hanya mendeteksi saja dan tidak dimungkinkan untuk handover
UARFCN = UTRA Radio Access Frequency Channel Number Cell reselection = perpindahan cell yang diduduki oleh MS
saat kondisi idle mode Handover = perpindahan cell yang diduduki oleh MS saat
kondisi dedicated mode
Istilah-istilah Pdp contex activation = sebuah event yang harus dilakukan
untuk memulai sebuah koneksi internet
Pdp contex Deactivation = sebuah event yang harus dilakukan oleh MS untuk mengakhiri sebuah koneksi internet
App.Troughput DL/UL = troughput DL/UL dari aplikasi yang telah di DL/UL oleh MS
How to drive test 3G ??????
Make a workspace of TEMS 8.03 Make a geoset from Map info Preparing tool Connected tool to Tems 8.03 Save log file Drive Test
Step by step to do drive test
Step by step to do drive testMake a workspace of TEMS 8.03
Step by step to do drive test
Make a workspace of TEMS 8.03 / map
Geoset manager
Open Map
Layer control
Add/edit themes
Clear mapRuler
• TabPresentation Positioning Map
Step by step to do drive testMake a workspace of TEMS 8.03/map
Geoset manager : berfungsi untuk membuat file geoset (file yang digunakan untuk menampilkan gambar site dan rute jalan).
Open map : berfungsi untuk membuka file geoset (.gst) Layer control : berfungsi untuk mengatur tampilan di map Add/edit themes : untuk melihat presentasi layer dan theme
saat ini, sert menambahkan apa saja yang ingin kita tampilkan
Step by step to do drive test
Make a workspace of TEMS 8.03 / Wcdma serving & neighbour
• Tab Presentation Wcdma Serving/Active set + neighbour
• Type : posisi cell dalam MS• Cell name : nama cell • Sc : scrambling code(kode acak yang terdapat pada tiap
sektor)• Cell id : identitas tiap cell atau sektor• Cpich Ec/No : (common pilot channel energi cell/noise)ukuran
kualitas suara pada wcdma atau sama dg Rx Qual di GSM dg Satuan dbm
• Cpich RSCP : (common pilot channel receive signal code power)Ukuran besar daya yang diterima MS dg Satuan dbm.
Step by step to do drive test
Make a workspace of TEMS 8.03 / Command sequence
• Tab Control Command Sequence
• Loop : pengulangan• Duration:lama panggilan(call establish)• Call type:jenis panggilan(bisa voice n video)• Time out : batas akhir terjadinya call attempt(sebelum
terjadinya call establish)
Step by step to do drive test
Make a workspace of TEMS 8.03 / Command sequence
Beberapa kolom yang harus dirubah settingannya sesuai dengan keperluan:• Phone book entry : jenis koneksi internet • Phone number : nomor dial up connection• Source file : file yang terdapat dalam ftp
server• Target file : letak penyimpanan file• Remote address : alamat ftp server tujuan• User & password : anonymous
Step by step to do drive test
Make a workspace of TEMS 8.03 / Events
• Tab Presentation Signaling Events
Step by step to do drive test
Make a workspace of TEMS 8.03 / Call analysis
• Presentation Analysis Call analysis
• Berisi rekaman terjadinya panggilan pada semua MS• Berisi waktu dan durasi dari semua panggilan• Window ini berguna untuk melihat lengkapnya panggilan yang
dilakukan oleh MS(call set up,call establish,call end).
Step by step to do drive test
Make a workspace of TEMS 8.03 / Wcdma data line chart
• Tab Presentation Wcdma Data service Wcdma data linechart
Step by step to do drive test
Make a workspace of TEMS 8.03 / Cellfile load
• Tab Configuration General Cellfile load
• Pilih browse lalu pilih file .cel • Cellfile load digunakan untuk menampilkan
cell name di window “wcdma sering / active set + neghbour”
• Namun hal ini bukan patokan utama untuk menentukan sector tiap site
Step by step to do drive test
Make a workspace of TEMS 8.03 / Equipment configuration
• Tab Configuration Equipment configuration
Step by step to do drive testMake geoset from map info
Open map info Open gcell.tab and gsite.tab Open file .tab that show road in your location
Step by step to do drive testMake geoset from map info / make label
To show sitename and cell name ◦ Open layer control and give point to automatic label for gsell and gsite table◦ Give points in automatic labels column◦ Tab label button
Step by step to do drive testMake geoset from map info/make geoset
Map that show in map info can made to be geoset:◦ Klik tools /tool manager/mapx geoset utility
◦ Tools/mapx geoset utility/save mapx geoset as
Step by step to do drive testPreparing tool
Laptop with TEMS Investigation and MapInfo Installed Laptop adaptor
Step by step to do drive testPreparing tool
Handset TEMS Complete (Handset, Charger, Headset) Data Cable and USB Hub
Step by step to do drive testPreparing tool
Inverter & Cable Inverter to Lighter Terminal Stop Contact
Step by step to do drive testPreparing tool
Place Handset and GPS where possible to get good signal and quality level
Step by step to do drive testConnected tool
Before connected tool, we have to show equiment configuration in Tems 8.03
Plug Tems K800i and GPS one by one to laptop
Step by step to do drive testConnected tool
Ms n GPS disconnect
Connect ALL
Step by step to do drive testConnected tool / lock to WCDMA n lock per sector
Step by step to do drive testConnected tool / gps connected
GPS connect it indicate by show in map window
Step by step to do drive testSave log file
Klick log file/recording properties
Select browse n select directory
Quick logging use to save log file automatic
If quick logging is checked, “swap file ..”must be fill.
Clear history use to clear history logfile before
Step by step to do drive test
Save log file
Klick log file/recording properties
Select browse n select directory
Quick logging use to save log file automatic
If quick logging is checked, “swap file ..”must be fill.
Clear history use to clear history logfile before
Start record
Name log file
Step by step to do drive testDrive test
• To start drive test don’t forget to start record then start command sequence
• Don’t forget to lock WCDMA
Step by step to do drive test
Drive Test
What we must do to get best drive test?1. Configure workspace2. Configure map3. Configure command sequence4. Connect ALL equipment5. Lock to wcdma6. Configure recording properties7. Start record8. Start command sequence9. Stop command sequence10.Stop record
Step by step to do drive test
Drive Test
What we must do to get best drive test?1. Configure workspace2. Configure map3. Configure command sequence4. Connect ALL equipment5. Lock to wcdma6. Configure recording properties7. Start record8. Start command sequence9. Stop command sequence10.Stop record
Step by step to do drive test
Drive test
If drive test has begun,please always do :
1. Check connection of the equipment (if there is one of them disconnect, we must stop and re drive test)
2. Navigate driver where we must go• if SSV and optimasi method,drive test must be in the
main lobe of antenna sector• If cluster and benchmark method, drive test must
route the road that have give by RF engineer
3. Check events, may be there is dropped call and blocked call (if there is dropped call we must start record again in the recent call end)
Methode of Drive Test Drive Test methode divided into :
1. SSV2. Cluster3. Benchmark4. optimasi
Ssv (single site verification) adalah metode yang digunakan untuk mengechek sinyal dari sebuah node B atau BTS yang baru on air
Contoh Metode drive test ◦ Routing ms1 voice 120 / 10 persector◦ Routing ms2 video 120 / 10 persector◦ Sho (soft handover)◦ Statik HSDPA download ftp server 5mb,5x,persector◦ Statik PS 3G download ftp server 2mb,5x,persector◦ ISHO 5x persector
Methode of drive TestSSV
Cluster adalah metode yang digunakan untuk mengetahui daerah mana yang mempunyai level sinyal yang buruk
Contoh Metode Drive Test• Round 1 1. Ms 1 voice 120/10
2. Ms 2 idle 3. Ms 3 ftp download server 500mb
• Round 2 1. Ms 1 video call 120 / 10 2. MS 2 ftp download server 500 kb
Methode of drive TestCluster
Benchmark adalah metode yang digunakan untuk membandingkan coverage sinyal antara beberapa operator
• Round 1 1. Ms 1 idle (operator A) 2. Ms 2 idle (operator B)
3. Ms 3 idle (operator C)
• Round 2 1. Ms 1 voice long call (operator A) 2. Ms 2 voice long call (operator B) 3. Ms 1 voice long call (operator C)
Methode of drive TestBencmark
Optimasi adalah metode yang digunakan untuk memperbaiki coverage sinyal yang buruk
• Before 1. Ms 1 voice (120 / 10) 2. Ms 2 video (120 / 10)
• After 1. Ms 1 voice (120 / 10) 2. Ms 2 video (120 / 10)
Methode of drive TestOptimasi
1. Export log file2. Analysis with Report Generator3. Plot with map info4. Plot with actix
Post Processing
Export log file with Tems 8.03 Tab log file/export logfile
Post ProcessingExport log file
Selected Ies : SAN Cell id part SAN CPICH RSCP SAN CPICH Ec/No SAN SC Lotitude Longitude
Post ProcessingExport log file
Post ProcessingAnalysis with Report Generator Open TEMS 8.03 Menu Tab Logfile Report Generator Add logfile
Setup Output directory
Setup Report Properties
Post ProcessingAnalysis with Report Generator
Setup IEs, Events, Mobiles, And User Details
Post ProcessingAnalysis with Report Generator
Result of Report generator in *.htm
Post ProcessingPlot with Map info
Open file from output export logfile
Post ProcessingPlot with Map info
Plot di atas masih terdapat simbol event-eventnya sehingga harus di hapus atau di simpan di file yang lain
Post ProcessingPlot with Map info/cut event
• Open query/sql select• Save table query dg “save copy as”• Cut tabel querynya kemudian tutup window nya
Post ProcessingPlot with Map info/create thematic map
• Create thematic map• Tab map thematic map Ranges (ketika plot
merupakan ranges angka-angka) • Tab map thematic map individual (ketika plot
merupakan individual )
Post ProcessingPlot with Map info/create thematic map
• Choose table and field• Klick next
• Configure thematic map by customize range, styles, legend
Post ProcessingPlot with Map info/create thematic map • Customize Range
• Customize styles
Post ProcessingPlot with Map info/create thematic map
• Customize legend
Post ProcessingPlot with Map info/create thematic map
• For example plot CPICH RSCP
Post ProcessingPlot with Actix
Post ProcessingPlot with Actix
Open log file Tab file open log file choose log file
Create super stream Tab tools create super stream choose
handset that want to be create