Differential pumping Thomson Scattering Beamline · CTH parameters: ⢠Aspect ratio ðŽðŽâ3...
Transcript of Differential pumping Thomson Scattering Beamline · CTH parameters: ⢠Aspect ratio ðŽðŽâ3...
CTH parameters: ⢠Aspect ratio ðŽðŽ â 3 â 4
⢠ð ð = 0.75 ðð , < ðð > = 0.2 ðð
⢠ðµðµ †0.7 ðð on axis
⢠0.02 †ιð£ð£ð£ð£ð£ð£ †0.32
⢠ðŒðŒððððð£ð£ððððð£ð£ †80 ðððŽðŽ
⢠ðððð †5 à 1019 ððâ3
⢠ðððð †200 ðððð
⢠ðððððððððððð †30 ðððð of ECRH
⢠ðððððððððððð â 200 ðððð of Ohmic drive
⢠Vacuum pressure â 1 à 10â8 ðððððððð
Thomson Scattering Beamline The CTH experiment
Future work
CTH* is a five field-period torsatron investigating the avoidance of disruptions over a wide range of plasma parameters.
Plasmas are created by launching an ECRH pulse to ionize Hydrogen gas, after which a plasma current is ohmically driven in this pre-established plasma resulting in a higher temperature and density.
CTH has the unique feature of operating with different ratios of vacuum to plasma transform. This allows CTH to control the magnetic topology from tokamak-like to stellarator-like.
*Supported by US DOE Grant DE-FG-02-00ER54610
[1]Schlossberg et al., Rev. Sci. Instrum 83, 10E335 (2012).
[2]Schoenbeck et al., Rev. Sci. Instrum 83, 10E330 (2012).
[3] Sheffield, John. "Noncollective Scattering." Plasma Scattering of Electromagnetic Radiation: Theory and Measurement Techniques. Amsterdam: Elsevier, 2011. 69-90. Print.
References
System Components
Thomson Scattering as a Plasma Diagnostic
Single Point Collection Geometry and Signal estimates
Proposed Beamline Geometry
Advantages of Thomson Scattering ⢠Non-invasive ⢠Non-perturbing ⢠Internal and local measurement
Thomson Scattering Basics ⢠Elastic scattering of electromagnetic radiation from free charged particles ⢠Electrons accelerate the radiationâs electric field causing the electrons to
reradiate. ⢠Scattered Intensity is proportional to the electron density and temperature
High Energy Nd:YAG Laser ⢠3.5 J at 1064 nm and 2 J at 532 nm ⢠Pulse width of 6-10 ns ⢠Rep rate of 10 Hz ⢠ðð2 â 7 ⢠Gaussian beam with beam waste of 12 mm
Motivation for Thomson Scattering: ⢠Internal, local measurement of electron density and temperature
⢠Improved Equilibrium Reconstructions with V3FIT especially for pressure profiles
⢠Better characterize CTH plasmas to understand disruptions and MHD activity
http://en.wikipedia.org/wiki/File:Thomson_scattering_geometry.png
Beam line design parameters
This is the input window at Brewsterâs angle
Laser beamline
Addressing the Challenges of Thomson Scattering
â Low number of scattered photons High Power laser Large Viewing solid angle
â Necessary stray light mitigation Geometrically confine stray light Actively filter and spectrally isolate
desired wavelengths â Complex system components
High throughput spectrometer, PMT, and laser are all commercially available
Single Point System Design Parameters
⢠Finish installation of beamline components and determine the correct focal length beamline optic ⢠Bench test collection optics with custom diffraction grating to determine output plane fiber bundles curvature ⢠Implement full design and calibrate the system including data comparisons to soft x-ray and interferometer measurements ⢠Use Thomson scattering data as internal conditions for the V3FIT code for improved equilibrium reconstructions
Laser Pulse
Beam dump. The length of the baffle system is constrained by concrete floor.
10â port acts as an outer baffle to absorb secondary stray light cone
Secondary aperture
Primary aperture
Input window at Brewsterâs angle
Green lines represent laser beam line
Red lines represent the. light scattered off of the Brewster window, primary stray light
Blue lines represent the light scattered off of the primary aperture, secondary stray light.
Turning mirror
Laser
Proposed position of focusing lens
ðŒðŒððð£ð£ð£ð£ððððððð ð ððð ð â ðððð
2ððððððððððexp
ðððððð2
2ðð2ðððð
ððððð£ð£ð£ð£ððððððð ð ððð ð ðððððððððððð
â ðððð2 ðððð ð¿ð¿ ðððð
ððððð£ð£ð£ð£ððððððð ð ððð ð ðððððððððððð
â 2.94 Ã 10â14
ððððð£ð£ð£ð£ððððððð ð ððð ð â1.7 ðœðœ
7Ã10â9ðð2.94 Ã 10â14
ððððð£ð£ð£ð£ððððððð ð ððð ð â 7 ðððð
Hamamatsu H11706-40 PMT Module ⢠5 mm diameter effective active area ⢠Fast gating FWHW of 1 µs ⢠Quantum Efficiency ~40% at 550 nm
Single Point System Design Parameters (cont)
Rotatable flange for brewster window alignment
1.33â half-nipples for magnetic feedthroughs and future diagnostics
Double o-ring seal for easy window replacement
Asymmetric spot size on window
HoloSpec Imaging Spectrograph ⢠f/1.8 allows for large throughput of light ⢠Option of Interference filter that rejects laser line
⢠532 nm laser light not focused onto imaging device ⢠Kaiser volume-phase holographic transmission grating
⢠Spectral coverage: 533.1 to 563.3 nm over 26.6 mm
Differential pumping half-nipple
1.33â half-nipple for leak valve
Installation of Beamline
View from 18â collection port
Focused beamline inside vacuum vessel
Large PCX Condenser Lenses ⢠Two adjacent plano-convex f/2 lenses ⢠150 mm clear aperture ⢠Effective f-number of optics: ~ f/1.5 ⢠AR coated for increased transmission
Spectrometer input Custom Fiber Bundle ⢠17.37 mm by 1.23 mm for spectrometer input ⢠450 fused silica fibers
⢠230 µm diameter including cladding ⢠N.A. 0.37
PMT input Custom Fiber Bundles ⢠Curved bundle to match curvature of spectrometer
output plane ⢠Fibers need N.A. > 0.42 ⢠Every spectral channel needs an individual bundle
Simulated Thomson signals
USB camera in the position of the single spectrometer-input fiber bundle, imaging a single spatial point on CTHâs midplane
Fused silica window
Beam damage from 5 m focal length lens
Installation of Collection Port
Manual shutter control
19.7 cm of clear aperture Shuttering
Extra 2.75â half-nipples
CTH Visible Spectra
Spectrometer
Five fiber bundles, each a unique spectral channel and curved to match induced off-axis curvature from the spectrometer
H11706-40 PMTs
Spectrometer and detector diagram