DE EN COMTRAXX® CP9xx – Touch Control Panel Series · 1 DE EN Quickstart Melde- und Bedientablea...
-
Upload
phungkhuong -
Category
Documents
-
view
224 -
download
0
Transcript of DE EN COMTRAXX® CP9xx – Touch Control Panel Series · 1 DE EN Quickstart Melde- und Bedientablea...
QuickstartDE EN
COMTRAXX® CP9xx – Touch Control Panel Series
Melde- und Bedientableau für medizinische und andere Bereiche Grafikschnittstelle zur Be-dienung und Überwachung von medizinischen und an-deren technischen Anlagen.
Bestimmungsgemäße VerwendungGrafikschnittstellen findenüberall Einsatz, wo komple-xe Informationen für einenAnwender einfach undüberschaubar dargestelltwerden sollen. Durch dieberührungsempfindlicheFläche dient es auch alsSteuerungsmöglichkeit von Anlagen. Eine andere oder darüber hinausgehende Benutzunggilt als nicht bestimmungsgemäß.
Sicherheitshinweise allgemeinBestandteil der Gerätedokumentation sind nebendieser Kurzanleitung die beiliegenden „Sicherheits-hinweise für Bender-Produkte“ und das Handbuchdes Geräts. Die Kurzanleitung ersetzt nicht dasHandbuch. Bitte lesen Sie auch die jeweiligen Handbücher derangeschlossenen Systemgeräte.
Sicherheitshinweise gerätespezifisch
Beschädigung von Bauteilen durchHerausnahme des Geräts aus dem UP-GehäuseNehmen Sie das Geräte nicht im laufen-den Betrieb aus dem Unterputzgehäuse. Trennen Sie vorher das Gerät von der Ver-sorgungsspannung und vom Netzwerk (Ethernet).
Beschädigung des Geräts durchfalschen AnschlusssteckerEin vorhandener Anschlussstecker einesanderen Geräts könnte eine abweichen-de Polung aufweisen. Verwenden Siezwingend den beigelegten Anschluss-stecker (A1+/A2–).
WARNUNG
VORSICHT
CP9xx_D00349_02_Q_DEEN /10.2018
Remote alarm indicator and operator panel for medical locations and other areas
Graphical interface foroperation and monito-ring of medical and othertechnical installations.
Intended useGraphical interfaces areused wherever complexinformation needs to bedisplayed easily andclearly for a user. Due toits touch-sensitive sur-face, it can also be usedas a control option for in-stallations.
Any other use than that described in this manual is re-garded as improper.
General safety instructionsPart of the device documentation in addition to thisquick-start guide are the enclosed "Important safetyinstructions for Bender products" and the device op-erating manual. The quick-start guide does not re-place the operating manual. Please also read therespective operating manuals of the connected sys-tem devices.
Device-specific safety instructions
Damage to components by removingthe device from the flush-mountingenclosureDo not remove the device from the flush-mounting enclosure during ongoing op-eration. First, disconnect the device from the supply voltage and from the network (Ethernet).
Damage to the device by using anincorrect connector plugAn existing connector plug of anotherdevice may have a different polarity. It isnesessary that you use the suppliedconnector plug (A1+/A2-).
WARNING
CAUTION
1
2
COMTRAXX® CP9xx – Touch
Functional descriptionMain functions:
• Indication and visualisation of system conditions, warning and alarm messages
• Centralised monitoring, control and parameter setting
• Output of visual and acoustic messages• Present values and setting of limit values for
recording
Application examples:• IT systems• Supply systems for medical gases• Air conditioning and ventilation systems• Room lighting• Communication systems• Operating theatre lights• Special power supply systems (BSV (battery-
based safety 0
Installation and connection
Dimensions
Risk of fatal injury due to electricshock!Touching live parts of the system carriesthe risk of electric shock. Before installingand connecting the device, make surethat the installation has been de-ener-gised. Observe the rules for working onelectrical installations.
DANGER
a
c
a
Device dimensions (mm) ±0.2
CP 907 CP 915a 226 505b 144 350c 153.8 350.7d 92,8 200e 36.1 77.15f 25.6 75
Installation dimensions flush-mounting box (mm)
CP 907 CP 915a 212 471b 124 314
Depth 75 86.5
FunktionsbeschreibungWesentliche Funktionen:
• Anzeige und Visualisierung von Systemzustän-den, Warnmeldungen und Alarmzuständen
• Überwachung, Steuerung und Parametrierung von einer zentralen Stelle
• Ausgabe von visuellen und akustischen Meldun-gen
• Aktuelle Werte und Festsetzung von Grenzwer-ten für die Aufzeichnung
Beispielhafte Einsatzbereiche:• IT-Systeme• Versorgungssysteme für medizinische Gase• Klima- und Belüftungssysteme• Raumbeleuchtung• Kommunikationssysteme• OP-Leuchten• Spezielle Stromversorgungssysteme (BSV oder
UPS)
Montage und Anschluss
Maße
Lebensgefahr durch Stromschlag!Bei Berühren von unter Spannung ste-hender Anlagenteile besteht die Gefahreines elektrischen Schlages. Stellen Sievor Einbau des Gerätes und vor Arbeitenan den Anschlüssen des Gerätes sicher,dass die Anlage spannungsfrei ist. Be-achten Sie die Regeln für das Arbeiten anelektrischen Anlagen.
GEFAHR
COMTRAXX®
e
b d
f
b
Geräte Abmessungen (mm) ±0,2
CP 907 CP 915a 226 505b 144 350c 153,8 350,7d 92,8 200e 36,1 77,15f 25,6 75
Einbaumaße Wandeinbaukasten (mm)
CP 907 CP 915a 212 471b 124 314
Tiefe 75 86,5
CP9xx_D00349_02_Q_DEEN /10.2018
CP9xx_D00349_02_Q_DEEN /10.2018
COMTRAXX® CP9xx – Touch Control Panel Series
Installation flush-mounting box CP907
Installation flush-mounting box CP915
Mounting manual Hager flush-mounting boxA special manual for the flush-mountingbox by Hager is included in delivery.
212
216
Einbau Wandeinbaukasten CP907
Einbaukasten CP915
Montageanleitung Hager EinbaukastenEine gesonderte Montageanleitung fürden Einbaukasten von Hager ist im Lie-ferumfang enthalten.
377
75
124128
3
4
COMTRAXX® CP9xx – Touch
Connection overview
Connections on the mainboard CP907
Legend
1 Connector digital inputs
2 I²C-Interface
3 Connector to energy storage board
4 Backbone Bus (not used)
5 Voltage supply
6 Ethernet (RJ45 PoE); HTTP, Modbus TCP, BCOM
7 X1 plug connector for Modbus RTU, BMS bus
8 Termination of Modbus RTU and BMS bus
13 Connection to control relay
COMTRAXX®
Ethe
rnet
(1:1
)
Beispiel Netzwerk (1:1-Verbindung)Example of peer to peer network
Bottom view
Top view
3
13
2
Anschlussübersicht
Anschlüsse an der Hauptplatine CP907
Legende
1 Steckbuchse digitale Eingänge
2 I²C-Schnittstelle
3 Steckbuchse zur Energiespeicherplatine
4 Backbone Bus (außer Betrieb)
5 Spannungsversorgung A1/+ A2/–
6 Ethernet (RJ45 PoE); HTTP, Modbus TCP, BCOM
7 X1-Stecker für Modbus RTU, BMS-Bus
8 Terminierung von Modbus RTU und BMS-Bus
13 Anschluss Steuerrelais
COMTRAXX®
1 2 12...
11 12 14
+
–~
Digital I/O
RelaisRelay
USB
BMS-Bus
Mod
bus
RTU
Ethe
rnet
Beispiel NetzwerkverbundExample of network system
Ansicht unten
Ansicht oben
1
4 5 6 78
CP9xx_D00349_02_Q_DEEN /10.2018
CP9xx_D00349_02_Q_DEEN /10.2018
COMTRAXX® CP9xx – Touch Control Panel Series
9
Connections on the mainboard CP915
Legend
Plug connector assignment
1 Connector digital inputs
2 I²C-Interface
3 Connector to energy storage board
4 Backbone Bus (not used)
5 Voltage supply A1/+ A2/–
6 Ethernet (RJ45); HTTP, Modbus TCP, BCOM
7 Termination of Modbus RTU and BMS bus
8 X1 plug connector for Modbus RTU, BMS bus
9 USB ports (for Touch Sensor)
10 DVI-Port
11 Audio Output
12 Audio Input
13 Connection to control relay
2
3
1310 11 12
Bottom view
Top view
141211
Steuerrelais Control relay
Terminierung Modbus RTU und BMS-Bus (8)Termination of Modbus RTU and BMS-bus (8)
Modbus RTU BMS
Anschlüsse an der Hauptplatine CP915
Legende
Belegung der Steckanschlüsse
1 Steckbuchse digitale Eingänge
2 I²C-Schnittstelle
3 Steckbuchse zur Energiespeicherplatine
4 Backbone Bus (außer Betrieb)
5 Spannungsversorgung A1/+ A2/–
6 Ethernet (RJ45); HTTP, Modbus TCP, BCOM
7 X1-Stecker für Modbus RTU, BMS-Bus
8 Terminierung von Modbus RTU und BMS-Bus
9 USB-Anschlüsse (für Touch Sensor)
10 DVI-Eingang
11 Audio Ausgang
12 Audio Eingang
13 Anschluss Steuerrelais
1
4 5 6 78
Ansicht unten
Ansicht oben
SBMSABMS BBMSAMB BMB SMB
SBMSABMS BBMSAMB BMB SMB
l1 l2 l3 l4 l5 l6 l7 l8 l9 l10 l11 l12
k1 k2 k3 k4 k5 k6 k7 k8 k9 k10 k11 k12
Belegung digitale Eingänge (1)Assignment of digital inputs (1)
Belegung X1 - Stecker (7)X1 plug connector (7)
5
6
COMTRAXX® CP9xx – Touch
CommissioningRequired information BEFORE commissioning:
• DHCP server available for CP9… and other BCOM devices?
• Fixed IP addresses for Modbus devices (e.g. IOM750-xxx)
• Subnet mask• IP address of the standard gateway• IP address of the DNS server
If a DHCP server is available in the network, the deviceaddress can be assigned automatically.
Initial commissioning of screen
Entering a manual address:• Switch on the supply voltage• Enter the desired IP address for the CP9…• Enter the subnet mask of the LAN• Enter the gateway address of the LAN • Press the "Save" button to store the entries • Wait 8-10 seconds
Activating address reception via a DHCP server
• Activate "DCHP?" checkbox• Press the "Save" button to store the entries• Wait 8-10 seconds
Login to the deviceFrom a local network LAN
• Open a browser on a device (computer/laptop) that is integrated into the network
• Enter the address indicated in line 1 of the CP9… into the address field of the browser
From a peer to peer networkIt is possible to connect the CP9… directly to a com-puter/laptop. In this case, the CP9… can be control-led with a second fixed IP address.
• Open a browser on the connected device• Enter the following address into the address line
of the browser: 169.254.0.1
InbetriebnahmeBenötigte Informationen VOR einer Inbetriebnahme:
• DHCP-Server verfügbar für CP9… und andere BCOM- Geräte?
• Feste IP-Adressen für Modbus-Geräte (z. B. IOM750-xxx)
• Subnetz-Maske• IP-Adresse vom Standard-Gateway• IP-Adresse vom DNS-Server
Ist ein DHCP-Server im Netzwerk vorhanden, kann dieAdressierung des Geräts automatisch vorgenommenwerden. Bildschirm Erstinbetriebnahme
Eingabe einer manuellen Adresse:• Spannungsversorgung einschalten• IP-Adresse für das CP9… eingeben• Subnetzmaske des LAN eingeben• Gatewayadresse des LAN eingeben• Eingaben speichern mit der „Save“-Taste • Warten Sie 8-10 Sekunden
Aktivierung des Adressempfangs von einem DHCP-Ser-ver
• Aktivieren Sie „DHCP?“• Eingaben speichern mit der „Save“-Taste• Warten Sie 8-10 Sekunden
Anmeldung am GerätAus einem lokalen Netzwerk LAN
• Öffnen Sie einen Browser auf einem im Netzwerk eingebundenen Gerät (Computer/Laptop)
• Geben Sie im Adressfeld des Browsers die Adresse der 1. Zeile des CP9… ein
Mittels direkt verbundenem PC (1 : 1 Verbindung)Es ist möglich das CP9… direkt mit einem Computer/Laptop zu verbinden. In diesem Falle lässt sich dasCP9… über eine zweite feste IP-Adresse ansteuern.
• Einen Browser auf dem verbundenen Gerät öff-nen
• Geben Sie in der Adresszeile des Browsers fol-gende Adresse ein: 169.254.0.1
CP9xx_D00349_02_Q_DEEN /10.2018
CP9xx_D00349_02_Q_DEEN /10.2018
COMTRAXX® CP9xx – Touch Control Panel Series
xx
EN
m
m s
COMTRAXX® start screen
COMTRAXX® manualFurther information about functionalityand configuration of the CP9… can befound in the COMTRAXX® manual.
ENT - SCT - PM - 5 - 118.07.2017 13:30
OK
OK 2
LOGIN to the device
LANGUAGE selection
SHOW MENU / HIDE MENU
SYSTEMS without faults
ALARMS with number of faults
Startbildschirm COMTRAXX®
COMTRAXX® HandbuchWeitere Informationen zu Funktionalitätund Konfiguration des CP9… sind imCOMTRAXX® Handbuch beschrieben.
TOOLS
ALARMS
BUS OVER VIE W
HOME
System OK
T_SCT_PM
1207990020-Bxxxxxx
Comtraxx CP907 V3.0
Device info
CP907COMTRAXX®
Syste
SysteAlarm
ANMELDUNG am Gerät
SPRACHEN Auswahl
ZEIGE MENÜ / VERSTECKE MENÜ
SYSTEME ohne Fehler
ALARME mit Anzahl von Fehlern
7
8
COMTRAXX® CP9xx – Touch Control Panel Series
Alle Rechte vorbehalten. Nachdruck und Vervielfältigung nur mit Genehmigung des Herausgebers.Änderungen vorbehalten!© Bender GmbH & Co. KG
ServiceService hotline: 0700-BenderHelp (Telephone and Fax)Carl-Benz-Strasse 8 • 35305 Gruenberg • GermanyTel: +49 6401 807-760 • Fax: +49 6401 807-629E mail: [email protected] • www.bender.de BENDER
Technical data
CP907Display.................................................................................. 17.6 mm (7“)Front.................................................................................. glass, temperedSupply voltage ........................................................ DC 24 V, PoE, < 15 WDimensions ................................................................ 226 x 144 x 78 mmWeight ............................................................................................. 1.1 kg
CP915Display.................................................................................38.1 mm (15“)Front.................................................................................. glass, temperedSupply voltage ................................................ AC 100…240 V / < 30 WDimensions ..................................................................505 x 350 x 92 mmWeight .............................................................................................. 6.1kg
CP924 Display.................................................................................61.0 mm (24“)Front.................................................................................. glass, temperedSupply voltage ....................................................................... coming soonDimensions .......................................................................... coming soonWeight ................................................................................. coming soon
Order numbers
Spare parts
Device Order number
CP907 B95061080CP915 B95061081CP924 Coming soon
Device Accessories Order number
CP907 Flush-mounting enclosure B95100140CP915 Front/Display B95061090
Flush-mounting box B95061091Mounting plate with electronics
B95061095
Flush-mounting box with electronics
B95061092
CP924 Front/Display Coming soonFlush-mounting box Coming soon
Mounting plate with electronics
Coming soon
Flush-mounting box with electronics
Coming soon
AllCP9… replacement plug con-
nector kitB95061910
Technische Daten
CP907 Display...................................................................................7“ (17,6 mm)Front ......................................................................................Glas, gehärtetVersorgungsspannung ........................................... DC 24 V, PoE, < 15 WMaße .......................................................................... 226 x 144 x 78 mmGewicht ............................................................................................ 1,1 kg
CP915 Display................................................................................ 15“ (38,1 mm)Front ......................................................................................Glas, gehärtetVersorgungsspannung .................................. AC 100…240 V / < 30 WMaße ...........................................................................505 x 350 x 92 mmGewicht ............................................................................................. 6,1kg
CP924 Display................................................................................ 24“ (61,0 mm)Front ......................................................................................Glas, gehärtetVersorgungsspannung .................................................................. in KürzeMaße ............................................................................................ in KürzeGewicht ........................................................................................ in Kürze
Bestellnummern
Ersatzteile
Gerät Bestellnummer
CP907 B95061080CP915 B95061081CP924 in Kürze
Gerät Zubehör Bestellnummer
CP907 UP-Gehäuse B95100140CP915 Front/Display B95061090
UP-Gehäuse B95061091Montageplatte mit Elektronik
B95061095
UP-Gehäuse incl. Montageplatte mit Elektronik
B95061092
CP924 Front/Display in KürzeUP-Gehäuse in Kürze
Montageplatte mit Elektronik
in Kürze
UP-Gehäuse incl. Montageplatte mit Elektronik
in Kürze
alle CP9… Ersatz-Steckerkit B95061910
CP9xx_D00349_02_Q_DEEN /10.2018
All rights reserved.Reprinting and duplicating
only with permission of the publisher.Subject to change!
© Bender GmbH & Co. KG
Bender GmbH & Co. KGPO Box: 1161 • 35301 Gruenberg • Germany
Londorfer Str. 65 • 35305 Gruenberg • GermanyTel.: +49 6401 807-0 • Fax: +49 6401 807-259
E mail: [email protected] • www.bender.de Group