cation and new product information after May 26, 2004, please refer to the Shimano...
Transcript of cation and new product information after May 26, 2004, please refer to the Shimano...
Compatibilities are subject to change without priornotice. Issued on May 26, 2004 SHIMANO INC.
2004-2005
Products compatibility information
135
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain InterchangeabilityDrivetrain Interchangeability
Rear derailleur (RD)Cassette sprocket (CS) Chain (CN)
Chain (CN)Rear derailleur (RD)Cassette sprocket (CS)
8-Speed HG
Mega-9 Drivetrain (9-speed HG)
CN-IG51CN-IG31
IG chain
RD-M960RD-M952RD-M800RD-M760RD-M750RD-M570RD-M510RD-C900RD-C600
RD-M580RD-M600RD-M805
Mega-9rear derailleur
CN-7701CN-HG93CN-HG73CN-HG53
CS-M960 (ba,ap,as)CS-M760 (aq,as)CS-HG70-9 (ar/au)CS-HG50-9 (ar/au)CS-M580
Mega-9cassettesprocket
9-speed HG
Mega-9 chainSuper
Narrow HG
Rear derailleur (RD)Cassette sprocket (CS) Chain (CN)
8-Speed LinkGlide
RD-C810RD-C505RD-C531
8-speedrear derailleur
CN-HG73
CN-HG53
CS-LG50 LinkGlidecassettesprocket8-speed
Mega-9 chainSuper
Narrow HG
* The rear derailleur for 8-speed can also be used for 7-speed drivetrain.
RD-T400SRD-C201
CS-HG60-8ICS-HG40-8I
11T-34T
CS-HG50-8I(an,aw)CS-HG30-8I(an,aw)
8-speed HGcassettesprocketIG chain
compatible
CS-HG60-8I(ao)CS-HG40-8I(ao)
11T-34T
RD-MC20 8-speedrear derailleur
RD-T400-SRD-C201
8-speedMGS
Low normal
RD-M340RD-CT95
8-speedSmart
30T max.
When using components of different series together, be aware of the points given below. “New” is shown if it is a new product and “MC” is given if only minor changes have been made.
NewNew
New
New
New
New
The full performance of LinkGlide will not be realized in combinations other than these. Also, HG performance will be reduced if RD-C505, C531 and C810 are used with HG gears other than LinkGlide gears. LinkGlide shifting performance is achieved when combined with ST-C503-A(R) as the shifting lever.( RD-C505/C531)
Rear drivetrain for Comfort & MTB Components
ARCHIVE
136
Co
mb
inatio
n &
Interch
ang
eability
Rear derailleur (RD)
MF-ZH06MF-TZ06
RD-TY186-speed
GS/SS
Multiple freewheel (MF)
7/6-speed/"SMARTCAGE"
MF-HG22
MF-HG40-6
MF-ZH36Top normal
14-28T
RD-FT30
14-28T
14-34T
13-34T
(
7-speed/MGSLow normal
Multiple freewheel (MF)
14-34T
14-28T
11-34T
MF-HG37MF-TZ07
RD-FT3011-28TMF-HG50-7
MF-HG40-7MF-TZ37
MF-HG50-7 RD-T300
7/6-speed/"SMARTCAGE"
Top normal
13-34TMF-ZH37RD-TX70RD-TX50RD-TX30
MF-Z015-5
Rear derailleur (RD)Multiple freewheel (MF)
5-speed UG
6-speed HG/ZH
RD-TY155-speed
GS/SS
Rear derailleur (RD)
CS-HG30-I RD-CT957-speed
rear derailleur
CN-HG50CN-UG50CN-UG51
HG/UGchain
Cassette sprocket (CS)
CS-HG-50-I RD-T300 7-speedMGS
11-34T
7-speed HG/ZHChain (CN)
UG
CS-HG30I7-speed HG
cassettesprocket
RD-M340 7-speedrear derailleur
Rear derailleur (RD)Cassette sprocket (CS)
7-speed HG
HG chain can only be used when using an HG compatible crankset
RD-TX70RD-TX50RD-TX30
CN-IG51CN-IG31 IG chain
Low normal
*
Drivetrain Interchangeability
NEW NEW
NEW (Front single)
(Front single)
ARCHIVE
137
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Rear drivetrain for Road bike components
SORA2200 series
DURA-ACEULTEGRA
105TIAGRA
ST-7700-BST-7700-C
ST-R500ST-3300
RD-3300RD-2200
CS-7700CS-6500
CS-HG70-9CS-HG50-9
ST RD CS FH
ST-6510ST-5510ST-4400ST-R600
RD-7800-SS
RD-6600-SS/-GS
Note-1 : Can not use this combination with a spoke protector.Note-2 : The FH components listed here cannot be used with 11T sprockets
FH-7800
9-speed
9-speed
DURA-ACEULTEGRA
10-speed
8-speed
CN-7701CN-HG93CN-HG73CN-HG53
CN
b a-2
4T b a-2
1T b a-1
9Tab
-17T ab
-15T
ab-1
3T12T
11T
HYP E R G L I D E - C J A P A N
U. S . PAT4268259
LOCK400kg/cm
ONAMI HS
ST-7800ST-6600
CS-7800CS-6600
(11, 12T TOP)
10-speed
RD-6500RD-5501RD-4400
FH-6600FH-7700FH-6500FH-5501FH-4400
8
8-speed
CS-HG90-8CS-HG70-8CS-HG50-8
ULTEGRA
FH-3300FH-2200
CN-HG91,90CN-HG70
CN-HG50
RD-7700
*Note-1
NEWNEW NEW
CN-7800CN-6600
CS-6600(13, 14, 15, 16T TOP)
NEW
NEW
ARCHIVE
138
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Interchangeability for flat handlebar
DURA-ACE ULTEGRA
105TIAGRA 9-Speed SL-R660
SL-R440
CS-7700CS-6500
CS-HG70-9CS-HG50-9
ST RD CS FH
ba-2
4T ba-2
1T b a-1
9Tab
-17T ab
-15T
ab-1
3T12T
11T
HYP E R G L I D E - C J A P A N
U. S . PAT4268259
LOCK400kg/cm
ONAMI HS
RD-7800RD-7700RD-6600RD-6500RD-5501RD-4400
CN-7701CN-HG93CN-HG73CN-HG53
CN
ST FD FC CNBB
SORA2200
8-Speed
SORA2200
8-Speed
SL-R440-8ST-R220
CS-HG50-8
ba-2
4T b a-2
1T b a-1
9Tab
-17T ab
-15T
ab-1
3T12T
11T
HYP E R G L I D E - C J A P A N
U. S . PAT4268259
LOCK400kg/cm
ONAMI HS
RD-3300RD-2200
FH-7700FH-6600FH-6500FH-5501FH-4400FH-3300FH-2200CN-7401
CN-HG91, 90CN-HG70CN-HG50
CN-7401CN-HG91,90
CN-HG70CN-HG50
FC-6503FC-5505
DURA-ACE ULTEGRA
105TIAGRA 9-Speed SL-R660
SL-R440
FC-7701FC-6500FC-5502
FD-R440
FD-R443
BB-6500BB-5500
BB-7700
BB-6500BB-5500
CN-7701CN-HG93CN-HG73CN-HG53
FC-3303FC-2203
SL-R440
FD-R440A
FD-R443A
Rear system
Front system
ST-R220
ST-R224
NEW
BB-ES71/51/30BB-UN73/53/25
FC-4401
FC-4400
BB-ES71/51/30BB-UN73/53/25
FC-4404
FC-4403
FC-3300FC-2200
FC-3301
BB-UN73BB-UN53BB-UN25
BB-ES71/51/30
FC-3304 BB-ES71/51/30
BB-UN73BB-UN53BB-UN25
ARCHIVE
139
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
FC-M572FC-M445FC-M440FC-M540FC-M470
44-32-22T
42-32-22T
FD-M960FD-M961FD-M760FD-M761-6FD-M580FD-M581-6FD-M581-3-44TFD-M600FD-M601
FD-M960-E
FD-M760-E
FD-M580-E
FD-M600-E
FD-M570-E
FD-M570
CN-7701CN-HG93CN-HG73
Front derailleur (FD)Chain (CN)
Front derailleur (FD)Crankset (FC)Chain (CN)
Mega-9 drivetrain (9-speed HG) / LinkGlide (8-speed)
IG triple (8 and 7-speed)
44-32-22T44-32-24T
FC-M960
FD-MC21, FD-MC18-S, FD-MC18-SE, FD-M330, FD-M330-EFD-T400-S
FC-T410FC-M340FC-MC20FC-MC19
FC-MC08FC-TS70FC-TS51
CN-IG51CN-IG31
IG chain
44-32-22TFC-M760FC-M580FC-M600
44-32-22TFC-M800-3
46-34-24TFC-C503FC-C510
FD-M571FD-M510FD-M511
FD-C510FD-C511
48-36-26T
FC-M510FC-M440FC-M470FC-M540
FD-M510FD-M511
Rear8-speed
* When using the front derailleur designed for a 7-speed system on an 8-speed system, the front derailleur plate may interfere with the chain even if it's installed correctly.
FC-C50546-34-24T
Front derailleur (FD)
Shift lever ( ST )
Crankset (FC)
SPCM ( TRIPLE )
FD-C505
ST-C505 for SPCM3
CN-HG73
CN-HG53 Rear8-speed
Mega-9 chainSuper
narrow HG
New New
New
New
New New
New
32-22TFC-M800-2
48-36-26TFC-M761-KFC-M581
FD-M761-3FD-M581-3-48T
New
New
New
FC-C810
46-34-24TFD-C810
Rear8-speed Di2
SPCM3
SPCM3
Front derailleur (FD)Crankset (FC)Chain (CN)
SPCM ( DOUBLE )
CN-7701CN-HG93CN-HG73
Mega-9 chainSuper
narrow HG
Mega-9 chainSuper
narrow HG
FC-C600
46-34TFD-C900FD-C600
9-speedSPCM
New
Front drivetrain interchangeability (MTB front SIS)
FC-C900 9-speed
ARCHIVE
140
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Front derailleur (FD)Crankset (FC)Chain (CN)
HG triple (8 and 7-speed)
CN-HG50CN-UG50
UG/HG chain 42-34-24T
FC-TY40FC-C050FC-TX70FC-TS31
FC-T411 FD-T401-S
FC-TY33FC-C051FC-TX71 48-38-28T
FD-C102
Rear8-speed
FD-T30042-34-24TFC-T300S
48-38-28TFC-T303 FD-T301
FD-C050FD-TY10
48-38-28T
Rear7/8-
speed
Rear7/8-
speed
Rear7/8-
speed
Rear7/8-
speed
42-34-24Rear7/6-
speed
FD-C101-EFD-CT92-E
* When using the front derailleur designed for a 7-speed system on an 8-speed system, the front derailleur plate may interfere with the chain even if it's installed correctly.
FC-C050FC-TX70FC-TS31
FD-TY30FD-C051
48-38-28TRear7/6-
speed
FC-TY33FC-C051FC-TX71
ARCHIVE
141
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Front drivetrain interchangeability (Road bike components)
ST-7700-BST-7700-C
FD-7700FD-6500FD-5501FD-4400
DURA-ACE 7700 seriesDouble9-Speed
9-Speed
8-Speed
8-Speed
2200SORATriple
2200SORA
Double
ULTEGRA6500 series
1055500 series
TIAGRADoubleTriple
ST-6510ST-5510ST-4400ST-R600
FC-6500FC-5502
BB-UN73/53/25
BB-6500BB-5500
BB-7700
FC-4400
FC-4403
BB-7703BB-6500BB-5500
FD-6503FD-5504FD-4403
CN-7701CN-HG93CN-HG73CN-HG53
CN-7401CN-HG90CN-HG91CN-HG70CN-HG50
FD-3300FD-2200
FC-3300FC-2200
FD-3304FD-2203
*1
*1
*2
ST FD FC BB CN
BB-UN73BB-UN53BB-UN25
BB-UN73BB-UN53BB-UN25
ST-R500ST-3300
FC-3303FC-2203
DURA-ACE 7700 series
TripleST-7703 FD-7703 FC-7703
ST-3304
*Notes 1 and 2: Axle length is differentNote 3: When the cable is adjusted normally, the front derailleur (FD) and chain (CN) may
contact when both the front and rear are in low gear. If this happens, please loosen the cable adjust barrel until the chain stops making contact.
DURA-ACE7800 seriesULTEGRA
6600 seriesDouble10-Speed
ST-7800
ST-6600
FD-7800
FD-6600CN-7800CN-6600
FC-7800
FC-6600
SM-FC7800
ULTEGRA 6603 series
Triple10-Speed
ST-6603 FD-6603 FC-6603NEW
NEW NEW NEWNEW
NEW NEW
*3
FC-3304BB-ES71BB-ES51BB-ES30
*2BB-UN73BB-UN53BB-UN25
BB-UN73BB-UN53BB-UN25
BB-ES71BB-ES51BB-ES30FC-3301
BB-UN73/53/25
FC-4401
FC-6503FC-5505
FC-4404 BB-ES71/51/30
BB-ES71/51/30
(SM-FC6600)
(SM-FC6600)
ARCHIVE
142
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Front derailleur and Crankset
The allowable combinations of front derailleurs and rear derailleurs depend on the difference in the number of teeth of the gears and the shape of the front derailleur plate.
Capacity
Top gearteeth number
Top-Middlemin. teeth difference
FC (top gear) - (low gear) =< FD (top and low capacity)
NOTE : When using the front derailleur designed for a 7-speed system on an 8-speed system, the front derailleur plate may interfere with the chain even if its installed correctly.
Front derailleur specifications (TRIPLE)
Crankset specifications
Front derailleurs and the number of teeth for corresponding cranksets are given in the chart below.
FC (top gear) - (middle gear) =< FD (minimum difference in teeth number between top and middle)
If the conditions given below are not satisfied, then the desired shiftability may not be obtained.
FD-M570-E
FD-MC21FD-T400-SFD-MC18FD-MC18-EFD-M330FD-M330-E
FD-M960FD-M960-EFD-M961FD-M760FD-M760-EFD-M761-DS6FD-M600FD-M601FD-M600-EFD-M580FD-M580-EFD-M581-6FD-M581-3-44T
FD-M805FD-M806
FD-M570FD-M571FD-M510FD-M511FD-C510FD-C511
FD-C810FD-C505
44T 42T
12T 10T
22T
44-32-22
32-22
22T
44/46T
12T
22T
48T/46T/44T
12T
22T
48T
12T
22T
SPCM
(46/34/24T)
SPCM
(46/34T)
20T
Mega-9 drivetrain SPCM (Triple)
FD-C900FD-C600
SPCM (Double)FD-T401-SFD-T301FD-C102FD-TZ31FD-C051
FD-T300FD-T300-EFD-C101-EFD-C050FD-TY10FD-CT92-EFD-TZ30FD-TY10
FD-TY30
42T
10T 8T
48T
20T
10T
48T
22T18T
Pro-Set alignment block
1 mm
3 mm
Gear teeth shouldcome within thisrange
Pro-Set gauge
A
How to set position for FC with bigger top gear chain ring in the same series.
1) set A2) Check if outer plate and bigger chainring have clearance3) Reposition height of FD in case problem at process (2)
FD-M761-3FD-M581-3-48T
Low gear
Top gear
Middle gear
FC-M510FC-M761-KFC-M581FC-M440FC-M470FC-M540
FC-M800-1FC-M960(44-32-24) *optionFC-M800-3FC-M760FC-M572FC-M510FC-M445FC-M440FC-M600-3FC-M580FC-M540FC-M470
FC-C503FC-C510
FC-C600
44T 34/38/42/46
32T
22T
48T
36T
26T
46T SPCM
46/34T34T
24T (-)
SPCM
46/34/24T
Bash Guard
32T
22T(-)
For Super Narrow chain For IG Chain For HG Chain For HG Chain
FC-M800-2 FC-T410FC-MC20FC-MC19FC-M340FC-MC08FC-TS70FC-TS51
FC-T300SFC-TY40FC-C050TC-TS31FC-TX70
FC-T303FC-TY33FC-C051FC-T411FC-TS38FC-TX71
42T
32T 34T
42T
22T
38T
48T
28T24T
FC-C810FC-C505
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW ARCHIVE
143
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Front derailleur and Chain line
Ø28.6 Ø31.8 Ø34.9(S) (M) (L)
FD-TY22GS
FD-TY18FD-TY30
47.5/50mm
47.5/50 mm
45mm
(down pull only)
43.5/45mm
45/47.5mm
(down pull only)
47.5/50mm(down pull only)
43.5/45mm(down pull only)
(down pull only)FD-TY05
FD-TY10
FD-TZ30FD-TZ31
FD-TY22SS
FD-TY15GS
FD-TY15SS
The Shimano line-up for front derailleurs and the chainlines they support are given in the chart below.
Shimano front derailleurs, with the exception of some of the C-series and the Tourney class, support chain lines of 47.5 and 50mm. The Tourney front derailleurs and corresponding chain lines are given in the chart below.
47.5 mm (shell width 68 mm), 50 mm (shell width 73 mm)
Ø 28.6(S)
Ø 31.8(M)
Ø 34.9(L)
47.5 / 50 mm
50 mm
57.5 mm (shell width of 83 mm)
50 mm
47.5/50 mm
52.5mm (shell width of 68mm)
50mm (shell width of 68mm)
50mm
47.5mm
the chainstay angle should be between 66 and 69
For the E-type (BB mounting front derailleur):47.5 mm (shell width of 68 mm)50 mm (shell width of 73 mm)
When using the FD-MC18SE with a seat tube of diameter 34.9 mm (L) the chainstay angle should be between 66 and 69
XTR
DEORE XT
DEORE LX
DEORE LX
DEORE
ALIVIO
ACERA
NEXAVE
SAINT
For the E-type (BB mounting front derailleur):47.5 mm (shell width of 68 mm)50 mm (shell width of 73 mm)
FD-M960 FD-M960-E
FD-M961
FD-M805, FD-M806FD-M760FD-M760-EFD-M761-6FD-M761-3
FD-M570FD-M570-EFD-M571
FD-M580, FD-M580-EFD-M581
FD-M510, FD-M511
HONE FD-M600, FD-M600-EFD-M601
FD-M330
FD-M330-E
FD-C900, FD-C600
FD-C810, FD-C505
FD-C510, FD-C511
FD-T300, FD-T301
FD-T400-S, FD-T401-S
FD-MC18-S, FD-MC18-SE
FD-MC21
With seat tube of diameter 34.9 mm (L), the chainstay angle should be between 66 and 69
73mm shell width/ 66 and 69
C-series
TOURNEY 30
TOURNEY 22
TOURNEY 15
TOURNEY 05
TOURNEY 10
TZ
For the E-type (BB mounting front derailleur) : 47.5 mm (shell width of 68 mm)50 mm (shell width of 73 mm)
For the E-type (BB mounting front derailleur) :47.5 mm (shell width of 68 mm)50 mm (shell width of 73 mm)
FD-C101-EFD-C102FD-C050
FD-C102
FD-C202
Front derailleur and chain line (MTB)
Front derailleur and chain line (Tourney)
NEW NEW
NEWNEW
NEW
NEWNEW
NEW
ARCHIVE
144
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Crankset, Bottom bracket, and Chain line
X: Yes
SeriesBottom Bracket
Spline Square ChaincaseXTR
HONE
FC-M960 X includeFC-M805-1FC-M805-2
include
FC-M805-3FC-M800-1
X
FC-M800-2FC-M800-3
X include
FC-M760 X includeFC-M761 X include
Deore LX FC-M580 X
FC-M510-OFC-M600
X BB-ES51(-E) 113 118 - -FC-M510-KO X X BB-ES51-K - 121
FC-M470(44T) X
FC-M440-O X - -FC-M440 X BB-UN25(-E) MM110
See page 61.
LL113 - -FC-C810 X X*** - 130 - -FC-C505 X X*** - 130 - -FC-C600 X X - - 117.5 -FC-C503FC-C530
XX XX X***
123 123 - 123
-FC-T410 X X -
--
123--
FC-T411 X X - - -FC-T300-S X X - -FC-T303 X X - -FC-MC20 X - -FC-MC19 X - -
Acera FC-M340 X X -Non-Series FC-MC08 X - -
Tourney FC-TY40 X - -C-Series FC-C051/050 X X - - -Tourney FC-TX70/TX71 X X - - -
Type of CrankCrankset
Deore
Model NO.
Chainline & Axle mark
47.5mm 50.0mm 52.5mm 47.5+tmmModel NO.
117.5
NEXAVE
YL117 ZL122BB-UN25(-E)
BB-UN25-K
BB-TS30/UN25-K
BB-UN25-K
BB-UN25
BB-UN25
SAINT
Deore XT
AlivioMM110 LL113BB-UN25(-E)
YL117 ZL122
BB-ES51/30(-E) 118113
BB-UN25
FC-M540 X BB-ES51(-E) 113 118
X
X
FC-M581 X includeX include
X
Comfort bike and MTB Components
In order to use SIS to its full extent, the required correct chain line, along with the crankset and bottom bracket required to obtain that, are given in the chart below.
without chaincase stayBB-UN25 bottom brackets parts for FC-C510 includes 1.8mm and 0.7mm thickness spacers.In case of without chain case, use both spacers between hanger and right hand BB adaptor. In case of with chain case, use 0.7mm thickness spacer only. Put chain case stay with 0.7mm thickness spacer between hanger and right hand BB adaptor.Chain case stay thickness should be 1.5 mm to 2.1 mm.
FC-C510**
***
***
/(-K)MM110
D-NL(122.5)
NEW
NEW
NEW
121121 126NEW
NEW
NEW
FC-M540-K X X BB-ES51-K 121121 126
NEW XFC-M460 X -BB-UN25(-K) 117.5 117.5FC-M440 (48T) BB-UN25(-K) 117.5 117.5- -
-XX
NEW
FC-M470(48T)NEW BB-ES51/30(-K)BB-ES51/30(-K)
X X 121121 126
----
NEW include
NEW
NEW
Chainline : 50 mm
Chainline : 50 mm
Chainline : 50 mm
Chainline : 57.5 mm
ARCHIVE
145
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Octalink Bottom Bracket
BB
Model NO. Chainring Square Chain
case Model NO. 46.5+t 47.5+t
FC-M510-K 44-32-22 X X - 117.5FC-TS91 44-32-22 X X - 117.5FC-TS52 44-32-22 X X - 117.5FC-TS38 48-38-28 X X -FC-TS32 42-34-24 X X -
Note: "t" is thickness of chain case stay. X: Yes
X: Yes
FC Chainline
BB-TS50/30
YL117
0<t<2.5mm
Front Chainwheels from Shimano Italy
The dimensions of the eight serrations on the BB are shown below.The dimensions for BB-ES71/51/30 are different from those for BB-M952/7700/7703/7710/6500/5500.Be aware that these models are not compatible.
BB-ES71BB-ES51BB-ES30BB-C900
BB-M952BB-7700BB-7703BB-7710BB-6500BB-5500
9
2.8
2.2
5
Capreo series componentsThe combinations of the front chainwheel and the bottom bracket to obtain proper chain line, which are necessary for the SIS (= Shimano Indexed System) to function well, are presented in the following chart.
* This specification can be used without the chain case as 52.5 mm chain line. In that case, a space is to be left between the shell and the adapter on the left side of the BB, but there is no problem in actual use.
Series
CapreoFC-F700
BB-UN40
BB-UN40-K
BB-UN25
BB-UN25-K
MM110
-
MM110
-
LL113
-
LL113
-
-
-
YL117
-
-
*117.5
-
*117.5
X X
FC BB Chain Line & Axle mark
Model No.Spline Square Chaincase
type of CrankModel No. 46.0
mm48.5mm
50.0mm
52.5+tmm
ARCHIVE
146
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Chain, Chainring and Cassette sprocket
The allowable combinations for the Shimano chain (CN), chainrings (FC), and cassette sprockets (CS) are given in the chart below. These chains are available in order to match the type of drivetrain. Select the combination you desire after checking the chart below.
Mega-9
Cassettesprocket
CassettesprocketCrankset Crankset Cassette
sprocket Crankset Cassettesprocket Crankset
IGLG HG
FC/CS
Chain
CS-M960
CS-M760
CS-M580
CS-HG70-9
CS-HG50-9
CS-LG50 FC-C810
FC-C505
FC-C503
FC-C530
FC-C510
CN-7701CN-HG93CN-HG73CN-HG53
FC-M960FC-M805FC-M800FC-M760FC-M761-KFC-M600FC-M581FC-M580FC-M572FC-M540FC-M470FC-M460FC-M445FC-M440FC-C600
CS-IG60
FC-T410
FC-MC20
FC-MC19
FC-M340
FC-MC08
FC-TS70
FC-TS51
CS-HG40-8I
CS-HG60-I
CS-HG50-8I
CS-HG50-I
CS-HG30-I
CS-HG30-8I
FC-T411
FC-T300-S
FC-T303
FC-TY40
FC-C050
FC-C051
FC-TX70
FC-TX71
FC-TS38
FC-TS31
Mega-9Super
Narrow chain
CN-IG51CN-IG31
IG Chain
HG Chain
CN-7401CN-HG50
Good Good Good Good
Good Good
Good Good
Not good
Not good
Not good
Not good Not good Not good
Not good Not goodNot good
Not good Not good Not good
Good
(Note 1)
(Note 2)Not good
poorperformance
Not good
poorperformance
Not good
Will notwork
Note 1: When used together with the HG cassette sprocket CS-M737/HG70-8, the adjustable range is very narrow and requires great care.
Note 2: The IG chain cannot be used with the Altus class rear derailleurs.
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
NEW
ARCHIVE
147
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Spoke protector
Select the spoke protector after checking the chart below.It is decided by hole number of hub and number of the gear teeth.
***
Protector 21T 25T 26T 28T 30T 32T 34T
CP-FH31
Hub
CP-FH40for 28H hub
CP-FH35
CP-FH02
CP-FH75*CP-FH56*
CP-FH76**
CP-FH50
for 32H hub
for 36H hub
for 10 speed32H hub
for ShimanoWheel
for (6-bolts) Shimano
Disc Brake Hubfor IF-C530
INTEGO36H Freehub
* Using with light alloy sprocket carrier ** Using with standard cassette sprocket***
Note: A spoke protector is included with the cassette sprocket CS-LG50.
Compatible cassette sprocketCP-WH11 : for CS-M750/M760/M960 (11-32T)CP-WH10 : for CS-M953/M960 (12-34T)
CS-M750/M760 (12-34T/11-34T)CS-HG70-9 (11-32T/11-34T)CS-HG50-9 (11-32T)
for WH-7701
for WH-M575/M540/M765/M965
5.4”
7.5”
5.4”
ø109
CP-FH05ø109
7.5”
5.4”
ø109
6.3”
CP-FH01
CP-WH71CP-WH10/11
for WH-R500
for WH-7800/R550CP-WH20CP-FH02/35
for FH-M755 / M756 / M525 / M475
for FH-M755/M756/M525/M475CP-FH75*CP-FH76**
6.3”
CP-FH53
CP-FH76**
CP-IF53****
CP-IF52****
CP-FH75*
CP-IF53****
for IF-C530INTEGO
32H FreehubCP-IF52****
Choose an appropriate spoke protector in the chart below.
FH-F700
24H
32H
36H
CP-FH35/FH31
CP-FH35
CP-FH31
FH Spoke Protector
Spoke protector for Capreo
NEW
NEW
for 10 speed36H hub CP-FH06ø109 NEW
NEW ARCHIVE
148
Co
mb
inatio
n &
Interch
ang
eability
Drivetrain Interchangeability
Spacer
FH-7700
FH-7800WH-7800
FH-66008/9 speed
FH/WH
FH-7800
Deep serration
Deep serration Shallow serration
Shallow serration
No!
WH-R550
X
Cassette sprocket compatibility will differ depending on the freehub (FH) and wheel (WH) used.
Be aware that freehub (FH) and wheel (WH) compatibility with CS-6600 might differ depending on the tooth combination.
*The tooth combination for CS-6600 JUNIOR type cannot be installed on FH/WH-7800.
A 1 mm spacer is required when combining CS-7800 and CS-6600 (except junior types) with a 8/9 speed freehub (FH) and FH-6600.
CS-7800 (all)CS-6600 (Standard 11T and 12T top gear combinations)
8/9 speedfreehuband FH-6600
FH-7800WH-7800
CS-7800 and CS-6600 (all)
CS-6600 (13, 14, 15, 16 top gear combinations for JUNIOR type)
*The serration depth is the same as for the 8 and 9 speed cassette sprocket.
CS-7800 and CS-6600 (standard 11 tooth and 12-tooth top gear tooth combination)
*The tooth combination for JUNIOR type cannot be installed on FH/WH-7800.
— =X =
WH-R500
X
WH-R540
—
WH-7701
X
WH-R535
—
WH-6500
—
WH-7700
—
FH-6600/8/9 speedfreehub
X
FH/WH-7800
X
Tooth
11 – 21
Model No.Type
CS-7800
XXXX———XX12 – 21CS-7800
XXXX———XX11 – 23CS-7800CS-6600
XXXX———XX12 – 23CS-7800CS-6600
XXXX—XXXX12 – 25CS-7800CS-6600
XXXX—XXXX12 – 27CS-7800CS-6600
XXXX—XXX—13 – 25CS-6600
XXXX—XXX—14 – 25CS-6600
XXXX—XXX—15 – 25CS-6600
XXXX—XXX—16 – 27CS-6600
Cassette sprocket, Rear freehub and Wheel (10-speed)
NEW
NEW
NEW
10 s
peed
sta
ndar
d10
spe
ed J
UN
IOR
ARCHIVE
149
Co
mb
inatio
n &
Interch
ang
eability
Disc b
rake
Disc brakeCombination Chart (Hydraulic Disc)
Shimano Hydraulic Disc Brake combination chart
Rotor Specification
In order to realize the best performance, we recommend that the following combination be used.
Series Caliper Mount type Brake Lever Roter PAD (option) Hose Remarks
BR-M965 Internationalstandard
BR-M966 Post mount
SAINT BR-M800 *1 ST-M765BL-M756
SM-RT80SM-RT80S
SM-RT75-DH
M06 Metal(M07-S resin) SM-BH62/BH63
*1 Front: Boxxer, Post (Manitou)& International standardavailable.Rear: International standard
Deore XT BR-M765 *2 ST-M765BL-M756
SM-RT77SM-RT75S
M07-S resin(M06 Metal) SM-BH62/BH63
BR-M555 Internationalstandard
BR-M555-M Post mount
BR-M525 *2 BL-M525 M08 Resin SM-BH59*2 Front mount: International
standard / Post mountRear mount: Internationalstandard
*2 Front mount: Internationalstandard / Post mountRear mount: Internationalstandard
NEXAVE BR-C901 Internationalstandard BL-C901 C01 Metal SM-BH60/61
SM-BH60/61
SM-BH62/BH63
BL-M555
BL-M556
Front only
XTR ST-M965 SM-RT96SM-RT75S
M07 Resin(M06 Metal) SM-BH96
DeoreSM-RT61
M01 Metal(M02 Resin)
Front Only
Deore LX BR-M585
BR-M601
*2ST-M585BL-M585ST-M600
SM-RT62 SM-BH59*2 Front mount: International
standard / Post mountRear mount: Internationalstandard
Series Model No. Outside Diameter CENTERLOCK System PCD 44 mm
XTR SM-RT96 160 mm X -
SM-RT80 203 mm -
SM-RT80S 160 mm -
SM-RT75-DH 203 mm -
-
-
X
SM-RT77 160 mm X -
SM-RT77L 203 mm X -
SM-RT75S
SM-RT75M
160 mm
170 mm
-
-
X
X
X
X
X: Yes
SM-RT60 160 mm -
SM-RT61 160 mm -
Oversized CENTERLOCK System
-
-
X
X
-
-
-
-
-
-
Deore LX
Deore XT
Deore /NEXAVE
SAINT
SM-RT62 160 mm X --
SM-RT62L 203 mm X --
NEW
HONENEW
Upda
ted
Upda
ted
Upda
ted
NEWNEW
NEWHONENEW
M07-S resin(M06 Metal)
M06 Metal(M07-S resin)
ARCHIVE
150
Co
mb
inatio
n &
Interch
ang
eability
Disc b
rake
Combination Chart (Mechanical Disc)
Shimano Mechanical Disc Brake combination chart
Mechanical Disc brake and Brake lever interchangeability
In order to realize the best performance , we recommend that the following combination be used.
Series
Model NO.
BL type
w/ SM-PM50
Good
Good
Good
Good
BL-C900/C600 type or w/ SM-PM40
Not good
Good
Not good
Not good
Not good
4 finger
Not good
Not good
Not good
Good
2 finger
Good
Good
Good
BR-M515-LA
BR-C601
BR-C501
BR-M475
4 finger w/ modulator
Caliper Mount type Brake Lever Rotor PAD
BR-M515-LA Internationalstandard
V-brake BL(1.5-2.5finger )
BR-M515-LA-MPost mountonly front
V-brake BL(1.5-2.5finger )
BR-C601 Internationalstandard
Internationalstandard
V-brake BL(4finger
w/ modulator )
BR-C501V-brake BL(4finger)
+ SM-PM50
Non-series
BR-M475V-brake BL
(1.5-2.5finger)
V-brake BL(1.5-2.5finger)
* FRONT MOUNT: International standard / Post mount * REAR MOUNT: International standard
*
BR-M495 *
SM-RT60
SM-RT61M05 Resin
SM-RT50For resin pad only
SM-RT52For resin pad only
M08 Resin
M08 Resin
DEORE
NEXAVE
BR-M465 *
GoodNot goodNot goodGoodBR-M495
GoodNot goodNot goodGoodBR-M465
Hose material & length
for Front for Rear
XTR SM-BH96 ST-M965 Cutable
SAINTDeore XT
Deore
SM-BH62SM-BH63
ST-M765BL-M756BL-M556
Cutable
SM-BH61 Cutable
SM-BH60 500-1000(every 50mm)
1200-1700(every 50mm)
SM-BH59
BL/BR-M525BL-M585ST-M585BR-M585
Cutable
Deore /NEXAVE
Series Model No.
900, 1300, 1700 mm
900, 1300, 1700 mm
900, 1300, 1700 mmBL/BR-M555,
BL/BR-C901
Resin
900, 1300, 1700 mm
Compatiblebrake lever &
caliperMaterial
Hose length (mm)
Deore LXHONE
SM-BH59ST-M585BL-M585ST-M600
Cutable900, 1300, 1700 mm
NEW
NEW
NEW
NEWNEW
NEW NEW
NEW
NEW
NEW
NEW
NEW
Updated
ARCHIVE
151
Co
mb
inatio
n &
Interch
ang
eability
V-brake and Canti-brake
V-BRAKE and Canti-brakeInterchangeability between brake systems
Depending on the brake and brake lever combination to be used, the relationship between the input at the brake lever and the actual braking force output at the wheels is very easily affected.
Be very careful when combining a brake and brake lever. Incorrect combinations can cause accidents or insufficient braking forces due to improper cable strokes. Be sure to carefully consult the chart below and select the brake and the matching brake lever.
Brakes
Brake levers
No!No!
No!
No!
No!
V-BRAKE
Note:1
BR-M960BR-M760BR-M570BR-M510BR-MC18
BR-T300BR-T300-S
BR-M420 with SM-PM40
ST-C505ST-C530ST-C503-ABL-T400ST-T400-SST-T300-SST-EF29 (4finger)SB-C055A (4finger)SB-8S20BL-IM60
ST-M960ST-M760ST-M580ST-M570ST-MC20ST-EF33ST-EF35ST-EF29SB-C055ASB-C055
BL-C600
V-Brake LeversWithpower
modulatormodel
Nexus/NEXAVE(Trekking bike lever)
With powermodulator model
Cantilever BrakeRoller Brake
Cantilever & Roller Brake
Levers
The “NO!” symbols indicate combinations that should not be used under any circumstances.No!
Note 1: This combination will not provide the sufficient amount of braking force.
BR-M430BR-M420BR-C600BR-M580
BL-M950BL-M739-SBL-MC18BL-M420BL-M950
BL-C800BL-IM65
NEW
Updated
Updated
Updated
NEW
Updated
ARCHIVE
152
Co
mb
inatio
n &
Interch
ang
eability
V-brake and Canti-brake
Brake component interchangeability
ST-T400/BL-T400/ST-T300/ST-EF29/SB-C055A/SB-7S45/BL-IM45 brake levers are equipped with a switch to change between the V-brake with modulator mode (BR-T300 and BR-M420 with SM-PM40) and the cantilever or roller brake mode.
For V-brake (with power modulator) mode
For Canti /Roller-brake.
V-position
V
V
C R
V-brake with power modulator
Good
Notgood
Notgood
Roller brake/canti brake
V-brake without power modulator
VV
C R
C R
Notgood
Notgood
Roller brake/ Canti brake
Good
Canti/roller(C R) brake-position
V-brake without power modulator
V-brake with power modulator
If the mode is not matched to the type of brake being used, this could result in inadequate or excessive braking power. Please proceed with caution when selecting the correct mode for the corresponding brake.
WARNING:
ARCHIVE
153
Co
mb
inatio
n &
Interch
ang
eability
V-brake and Canti-brake
ST-R220/R224/R223 brake levers are equipped with a switch to change between the V-brake with modulator mode and the caliper brake, canti brake or roller brake mode.
For V-brake (with power modulator) mode
For Caliper/Canti/Roller-brake.
V-position
V
V
C R
V-brake with power modulatorV-brake + SM-PM40
V-brake + SM-PM40
Good
Notgood
Notgood
Cariper brake / Roller brake / canti brake
V-brake without power modulator
VV
C R
C R
Notgood
Notgood
Cariper brake / Roller brake / canti brake
Good
Caliper/Canti/roller(C R) brake-position
V-brake without power modulator
V-brake with power modulator
If the mode is not matched to the type of brake being used, this could result in inadequate or excessive braking power. Please proceed with caution when selecting the correct mode for the corresponding brake.
WARNING:
ARCHIVE
154
Hub roller brakeInterchangeability between hub and roller brake
Hub roller brake and Front hub w/modulator
Hub roller brake and Hub Dynamo w/modulator
Hub roller brake and Front hub w/modulatorFor 20" to 24" bike ( for Children )
Hub roller brake and Hub Dynamo w/modulatorFor 20" to 24" bike ( for Children )
Model NO. Modulator Level type BR-IM75-F BR-IM70-F BR-IM50-F BR-IM41-F BR-C050-IM-F
HB-IM70 Hyper QR not good not good not good
HB-IM50 Normal QR not good
HB-IM45 Normal NUT
HB-IM40 Normal NUT
HB-C052-IM Hyper NUT not good not good
HB-IM20-E Hyper NUT not good not good
: Recommended combination: Usable
: Recommended combination: Usable
Model NO. Modulator Level type BR-IM75-F BR-IM70-F BR-IM50-F BR-IM41-F BR-C050-IM-F
HB-IM30 20-24inches NUT
HB-IM20-EC 20-24inches NUT
HB-C052C-IM 20-24inches NUT
good
Model NO. Modulator Level type BR-IM75-F BR-IM70-F BR-IM50-F BR-IM41-F BR-C050-IM-F
QR not good not good not good
NUT not good not good
DH-2R40 Hyper NUT not good not good
QR not good not good
NUT
HB-NX60 Normal NUT
HB-C051-DR Hyper NUT not good not good
HB-C050-DR Hyper NUT not good not good
DH-3R40 Hyper
HB-NX50 Normal
Model NO. Modulator Level type BR-IM75-F BR-IM70-F BR-IM50-F BR-IM41-F BR-C050-IM-F
HB-C051-DRC 20-24inches NUT
HB-C050-DRC 20-24inches NUTgood
Co
mb
inatio
n &
Interch
ang
eability
ARCHIVE
155
Co
mb
inatio
n &
Interch
ang
eability
Brake sh
oe
Brake shoeBrake shoe (for V-brake and Canti-brake)
Brake/Shoe Iine-up
Shoe characteristics
M70R2M70R2(Severe
Conditionshoe)
Ceramic M70T3 M70T4M70CT4(Severe
Conditionshoe)
M70W M65T3 M65T4 S70CS70C
(SevereCondition
shoe)
S70T S65T
BR-M960 Standard - Option - - - - - - - - - -BR-M760 Option
-
- Option Low noise Option - - - - Standard - - -
BR-M570 - - Option Option - - - - - - Standard -BR-M510 Option - - Option Option - - - - Standard - Standard
BR-M430 Option - - - - - - - - Standard - - -BR-M420 - - - - - - - Option Option - - - Standard
BR-M330 - - - Option Option - - - - - - - Standard
BR-C900 - - - - - - Standard - - - - - -BR-C600 - - - - - - Standard - - - - - -BR-T300 - - - Option Option - - - - - - Standard -BR-MC18 - - - Option Option - - - - - - Standard -BR-CT91
BR-R550 - Option - - - Option - - - - Standard - -Standard shoe is ''CONVENTIONAL TYPE''. M55T M-system shoe is optional choice.
BR-M580 - - - Option Option - - - - Standard - - -
Cartridgeshoe M-system Length Threaded
shoe post Brake shoe characteristics
M70R2 X X 70 mm XA race shoe that performs well in dry and wet conditions, and is also highly resistant to wear.may give off noise.
M70R2(Severe Condition shoe) X X 70 mm X +1mm thicker shoe with M70R2
Ceramic X - 70 mm X Specific shoe for ceramic rims.
M70T3 - X 70 mm X
M65T3 - X 65 mm X
M70T4 - X 70 mm X
M70W - X 70 mm X
M65T4 - X 65 mm X
M70CT4(Severe Condition shoe) X X 70 mm X Cartridge shoe with M70T4
S70C X - 70 mm X
S70T - - 70 mm X
S65T - - 65 mm X
S70C(Severe Condition shoe) X - 70 mm X
X: Yes
+1mm thicker shoe with S70C
Performs especially well in wet conditions andmay pass DIN standards.Gives off less noise, butthe pad is heavier, faster rim wear, and tends tofade.
Only for side wall machined rims. Performs especially well in wet conditions and may passDIN standard. Tend to be low noise, low rim wearand fade.
Performs well in dry conditions and tends to be low noise. Wears in muddy conditions.
NEW
ARCHIVE
156
Co
mb
inatio
n &
Interch
ang
eability
Brake sh
oe
Brake shoe (for road bikes)
< Brake/Shoe Iine-up >
Brake shoe (Capreo)
< Shoe characteristics >
< Shoe characteristics >
R55C2 R55C +1 R55C R55HC R55C forCarbon rim
R55C forCeramic rim M50T R50T
BR-7800 Standard Option - - Option Option - -
BR-7700 - Standard - Option Option Option - -
ULTEGRABR-6500 - - Standard Option Option Option - -
105 BR-5501 - - Standard Option Option Option - -
non-series BR-R600 - Standard - Option Option Option - -
TIAGRA BR-4400 - - - - - - Option Standard
SORA BR-3300 - - - - - - Option Standard
non-series BR-A550-57 - - - - - - Option Standard
DURA-ACE
BR-6600 Standard - - - Option Option - -
Cartridgeshoe M-system Length Brake shoe characteristics
R55C2 - 55 mmPerforms well in dry conditions and tends to below noise. Highly resistant to wear in rainy conditions.
R55C +1 - 55 mm * 1 mm thicker shoe with R55C
R55C - 55 mmPerforms well in dry conditions and tends to be low noise. Wear in rainy conditions.
R55HC 55 mmPerforms well both in dry and wet conditions. But may give off noise, faster rim wear, and tends to fade.
R55Cfor Carbon rim - 55 mm For Carbon rim
R55Cfor Ceramic rim 55 mm
X
X
X
X
X
X For Ceramic rim only
M50T - 50 mm
X
X
XPerforms well in wet conditions. But faster rim wear.
R50T - - 50 mmPerforms well in dry conditions and tends to be low noise. Wears in rainy conditions.
Shoe Cartridgeshoe
M-system
R55C(for F700) X X
Length
55 mm
ThreadShoe Post
X
X: Yes
X: Yes
Brake Shoe Charectristic
Performs well in wet conditionsand may pass DIN standards. Tends to be low noise. But faster rim wear.
NEW
ARCHIVE
157
Co
mb
inatio
n &
Interch
ang
eability
Brake p
ad
Brake padBrake pad line-up (for disc brake)
M01/M03/M06 : Longer pad-life, good for anti-fade, good constancy either dry/wet. May cause noise while braking.M02/M04/M05/M07/M07-S : Same level performance as metal pad. Shorter pad-life than metal. M08 : Do not use M08 brake pads in combination with the BR-M515/BR-M515-LA and BR-C601 brake system. If M08
brake pads are used, the brake arm and caliper will touch before the pad wear indicator is noticed and a noise indicating that the pads need to be replaced is heard, and this will result in a gradual reduction in braking performance until ultimately the brakes stop working.
C01 : Easy, controllable metal pad, good for trekking use.
M01
Sintered Metal
Standard
M02
Resin
option
M03
Sintered Metal
M04
Resin
M07-S
Resin
option
Standard
option
Standard
M05
Resin
Standard
Standard
M06
Sintered Metal
option
Standard
option
Standard
option
M07
Resin
Standard
M08
Resin
Standard
Standard
Standard
Standard
Standard
C01
Sintered Metal
Standard
Model NO.
BR-M965BR-M966BR-M800
BR-M765
BR-M755
BR-M601
BR-M585
BR-M555
BR-M525
BR-M495
BR-M465
BR-M515
BR-M475
BR-C901
BR-C601
BR-C501
type
Hydraulic
Hydraulic
Hydraulic
Hydraulic
Hydraulic
Hydraulic
Hydraulic
Hydraulic
Mechanical
Mechanical
Mechanical
Mechanical
Hydraulic
Mechanical
Mechanical
Standard option
NEW
NEW
NEW
NEW
Disc brake caliper / Rotor combination
BR-M965BR-M966BR-M765BR-M755BR-M800BR-M601BR-M585BR-M555BR-M525BR-C901BR-M515BR-M495BR-M465BR-M475BR-C601BR-C501
Notes: • SM-RT52; Compatible with resin pad caliper specification only. If use with caliper with metal pads, rotor will be easily damaged • SM-RT50; Compatible with BR-M475/C501 only*1; For Manitou post mount*2; Large size centerlock ring
SizeCenter Lock
CaliperModel No.
Item SM-RT96160mm
XXXXXXXXXXXXXXXXX
SM-RT80203mm*2
XXXXXXXXXX———————
SM-RT80S160mm*2
XXXXXXXXXXXXXXXXX
SM-RT77160mm
XXXXXXXXXXXXXXXXX
SM-RT77L203mm
XXXXXXXXXX———————
SM-RT75M170mm
————
Manitou*1————————————
SM-RT75-DH203mm
—XXXXXXXXX———————
SM-RT62160mm
XXXXXXXXXXXXXXXXX
SM-RT62-L203mm
XXXXXXXXXX———————
SM-RT61160mm
—XXXXXXXXXXXXXXXX
SM-RT52160mm
XXXXXXXXXX—XXXXXX
SM-RT50160mm
——————————————X—X
NEWNEW
NEWNEW
ARCHIVE
158
Co
mb
inatio
n &
Interch
ang
eability
Disc brake mount adapterDisc brake mount adapter application
How to read Model NO.
SM - MA - F 203 S / P
Mount adapter / Model NO.
SM-MA-F203S/S
SM-MA-F203S/B
SM-MA-F203S/P
SM-MA-R203S/S
SM-MA-F160P/S
SM-MA-R160P/S
SM-MA-F170S/P
SM-MA-F203P/S
SM-MA-R203P/S
SM-MA-F203S/Z
SM-MA-F203P/Z
SM-MA-F203P/B
SM-MA-F203P/P
SM-MA-F160P/Z
Mount adapter
Rotor size
Caliper mount-type S = Int-A-standard P = Post
Mount-type (Suspension-type) International A-standard = S Post = P Boxxer = B Marzocchi = Z
Front = FRear = R
Small parts
Shimano hydraulic disc brake mount adapter application table
< For front >
A-standard MARZOCCHI 20 mm Axle(QR 20 Plus-DH INTL STD) BOXXER-type POST-type
ø 203 SM-MA-F203S/S SM-MA-F203S/Z SM-MA-F203S/B SM-MA-F203S/P
ø 160 Direct attach
ø 203 SM-MA-F203P/S SM-MA-F203P/Z SM-MA-F203P/B SM-MA-F203P/P
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attach
ø 203 SM-MA-F203P/S SM-MA-F203P/Z SM-MA-F203P/B SM-MA-F203P/P
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attach
ø 203 SM-MA-F203P/S SM-MA-F203P/Z SM-MA-F203P/B SM-MA-F203P/P
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attach
ø 203 SM-MA-F203S/S SM-MA-F203S/Z SM-MA-F203S/B SM-MA-F203S/P
ø 160 Direct attach
ø 170 SM-MA-F170S/P
ø 203 SM-MA-F203S/S SM-MA-F203S/Z SM-MA-F203S/B
ø 160 Direct attach
ø 203 SM-MA-F203P/S SM-MA-F203P/Z SM-MA-F203P/B SM-MA-F203P/P
ø 160 SM-MA-F160P/Z Direct attach
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attach
Model Rotordiameter
Mount-type
BR-M965
BR-M966
BR-M800
BR-M765BR-M601BR-M585
BR-M755
BR-M555
BR-M555-M
BR-M525ø 203 SM-MA-F203P/S SM-MA-F203P/Z SM-MA-F203P/B SM-MA-F203P/P
NEW
NEW
ARCHIVE
159
Co
mb
inatio
n &
Interch
ang
eability
Disc brake m
ount adapter
A-standard A-standard(MARZOCCHI) BOXXER-type POST-type
ø 203
ø 160 M515 Adapter (F)
ø 203
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attach
ø 203
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attach
Rotordiameter
Mount-typeModel
BR-M515
BR-M515-M
BR-M495BR-M465
Model Rotor diameter A-standard
ø 203
ø 160 M515 Adapter ( R )
ø 203
ø 160 SM-MA-R160P/S
ø 203
ø 160 M475 Adapter ( R )
BR-M515
BR-M515-M
BR-M465BR-M495
Shimano mechanical disc brake mount adapter application table
Model Rotor diameter A-standard
ø 203 SM-MA-R203S/S
ø 160 Direct attach
ø 203 SM-MA-R203P/S
ø 160 SM-MA-R160P/S
ø 203 SM-MA-R203P/S
ø 160 SM-MA-R160P/S
ø 203 SM-MA-R203P/S
ø 160 SM-MA-R160P/S
ø 203 SM-MA-R203S/S
ø 160 Direct attach
ø 203 SM-MA-R203S/S
ø 160 Direct attach
ø 203 SM-MA-R203P/S
ø 160
ø 203
ø 160 SM-MA-R160P/S
BR-M965
BR-M966
BR-M800
BR-M765BR-M601BR-M585
BR-M755
BR-M555
BR-M555-M
BR-M525
< For front >
< For rear >
< For rear >
ø 203
ø 160 SM-MA-F160P/S SM-MA-F160P/Z Direct attachBR-M475
ø 203
ø 160 M475 Adapter ( R )BR-M475
SM-MA-R203P/S
NEW
NEW
NEW
NEW
NEW
NEW
ARCHIVE