Brushless Motor Fundamentals
description
Transcript of Brushless Motor Fundamentals
![Page 1: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/1.jpg)
Brushless Motor Fundamentals
4.3~4.7. Series and Parallel Connections
2 월 22 일 곽규열
![Page 2: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/2.jpg)
4.3 Multiple Phases
• 단상모터는 모든 지점에서 토크를 발생시키지 못하므로 잘 쓰이지 않는다 .
• 180ºE 에서의 back EMF 와 토크는 영이 된다 . 이 지점에서 토크는 토크를 만들 수 없다 .
• 모터가 위의 지점에서 정지상태가 된다면 , 외부에서 물리적인 힘을 주지 않는다면 로터는 회전을 하지 않는다 .
• 위의 문제점을 제거하고 일정한 토크를 발생시키기 위해서 단상보다 많은 상을 이용한다 .
• 대부분의 모터는 삼상을 가지고 있다 .
• 삼상보다 많은 상은 흔한 경우가 아니다 . 높은 출력을 요하는 출력장치의 경우에만 삼상보다 많은 상을 사용한다 .
![Page 3: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/3.jpg)
4.3 Multiple Phases
Fig 1. A three phase motor
• the zero crossings of the back EMF and torque → (360ºE)/3 → 120ºE or 60ºM
• Phase A, phase B, and phase C 모두같은파형을가진다 .
• Phase A and B 는 120ºE 만큼의오프셋을가진다 .
마찬가지로 phase A and C는 -120ºE 만큼오프셋을가진다 .
![Page 4: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/4.jpg)
4.3 Multiple Phases
Fig 2. Back EMF and torque waveform for a three phase motor
![Page 5: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/5.jpg)
4.4 Design Variations
Fractional Pitch Coils
→ When the coil pitch differs from 180ºE, the winding is called a fractional pitch winding.
Fig 3. Motor having on fractional pitch coil
/c c p
coil pitch factor
![Page 6: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/6.jpg)
4.4 Design Variations
Fig 4. Motor with rotor at 60ºE
The flux linkage increases from the minimum to zero
![Page 7: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/7.jpg)
4.4 Design Variations
Fig 5. Motor with rotor at 120ºE
• The flux linkage reaches a maximum
• The flux linkage remains at the maximum until θe = 180º
• It starts decreasing through zero to the minimum again
![Page 8: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/8.jpg)
4.4 Design Variations
Fig 6. Flux linkage and back EMF for the fractional pitch coil case
Fig. 5
Fig. 4
Fig. 3
![Page 9: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/9.jpg)
4.4 Design Variations
Fractional Pitch Magnets
→ Magnets seldom span a full pole pitch of 180ºE because flux at the transitions between North and South poles not contribute to torque
Fig 7. A motor having fractional pitch magnets
ro m stA R LConsidering the flux in the air gap over the magnet surface only.
No flux crosses the air gap over the gaps between the magnets
![Page 10: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/10.jpg)
4.4 Design Variations
Fig 8. Flux linkage and back EMF for the fractional pitch magnet case
![Page 11: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/11.jpg)
4.4 Design Variations
Fractional Slot Motor
• Nspp = Ns/Nm/Nph slot per pole per phase
• When Nspp = an integer, the motor is said be an integral slot motor
• When Nspp ≠ an integer, the motor is said be a fractional slot motor
• There is a distinction between a motor having fractional windings and a fractional slot motor. The first characterizes the windings; the second characterizes the slots that contain windings
![Page 12: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/12.jpg)
4.4 Design Variations
Fig 9. A fractional slot motor
Ns = 15 slots,
Nm = 4 magnet poles,
And Nph = 3 phases
→ Nspp = 1.25 and
the angular slot pitch
θs = 360ºM/Ns = 24ºM or 48ºE
![Page 13: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/13.jpg)
4.4 Design Variations
Fig 10. Phase A winding for a 4 poles, 15 slot motor
There are 3 phases, 15 slots, and each coil fills a net one slot
→ Ncph = Ns/Nph
= 15/3 =5
![Page 14: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/14.jpg)
4.4 Design Variations
Fig 11. Flux linkage and back EMF of coil Ca
Offset
θab=4·48ºE=192ºE
θac=7·48ºE=336ºE
θad=8·48ºE=384ºE
θae=11·48ºE=528ºE
Coil Cb and Ce are woung in the opposite direction
![Page 15: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/15.jpg)
4.4 Design Variations
Fig 12. Sum of coil back EMFs to get net winding back EMF
0
0
( ) ( ) ( 192 ) ( 336 )
( 384 ) ( 528 )
( ) ( 12 ) ( 24 )
( 24 ) ( 12 )
a a a
a a
a a a
a a
e e e e
e e
e e e
e e
![Page 16: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/16.jpg)
4.5 Coil Resistance
• Multiple coils connected together to form phases are a basic part of all motors.
• Coils have two electrical properties, namely resistance and inductance
• Resistance is a property of all materials. It represents a measure of how much the material the flow of current.
( )
lR
Awhere the resistivity of the material m
l the material length along the direction of current flow
![Page 17: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/17.jpg)
4.5 Coil Resistance
In general, material resistivity is a function of temperature.
0 0
0
( ) ( )[1 ( )]T T T T
where T temperature
T a base temperture
the thermal resistivity coefficient
![Page 18: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/18.jpg)
4.5 Coil Resistance
Coils in motors are most commonly composed of multiple turns of round insulated wire
• The centermost circle is the bare conductor
• The next outer layer is the wire insulation, which is commonly available in three thickness, single, double, and triple
• The final layer is an optional layer of bonding material
Fig 13. Wire cross section
![Page 19: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/19.jpg)
4.5 Coil Resistance
Several standards exist for classifying wire according to diameter. The most common standard is American Wire Gage(AWG)
8.24865(0.890526)
int
( )
Gwb
wb
d
where G the eger wire gage
d the bare wire diameter mm
As the gage increases, the diameter decreases.
log8.24865
log 0.890526
wbd
G
![Page 20: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/20.jpg)
4.5 Coil Resistance
Because AWG is based on a geometric progression, wire gages are related to each other by ratios
Fig 14. Relative wire resistance versus wire gage
![Page 21: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/21.jpg)
4.5 Coil Resistance
• The above figure plots resistance relative to a wire having any gage G to wires having gages G, G+1, etc.
• A wire of gage G+3 has twice the resistance of a wire of gage G. So two wires of gage G+3 taken in parallel have the same resistance as on wire of gage G
• At G+1, resistance is approximately 26% greater than that at G. So increasing the wire gage by one, increases resistance and I2R losses by 26% provided current remains constant.
• At G-1, resistance decreases approximately to about 79% of that at G. So, decreasing the wire gage by one, decrease the I2R losses for fixed current to 79% of what they are at G.
![Page 22: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/22.jpg)
4.6 Coil Inductance
• Inductance is not usually a critically parameter in brushless permanent magnet motors.
• Inductance determines the time constant of the windings.
• When a coil is placed in stator slots, its inductance changes dramatically compared to its inductance when surrounded by air.
•Mutual inductance exists between the coils in a given phase as well as between the coils in different phase.
• Mutual inductance between coils in a given phase is considered here, but mutual inductance between coils in different phases is not. Because mutual inductance between phases is small relative to self inductance
2 21 1
2 2VLi H dV
![Page 23: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/23.jpg)
4.6 Coil Inductance
When coils are placed in slots, the coil inductance has three distinct components due to the three distinct area where significant magnetic field is created by coil current.
→ The air gap, the slots, and the end turns
Air Gap Inductance
→ The air gap inductance component is due to the flux crossing the air gap
→ Consider the magnetic circuit model that the MMF is produced by the stator coils and ignore the flux source in the magnet model
![Page 24: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/24.jpg)
4.6 Coil Inductance
Fig 15. Magnetic circuit model for the computation of air gap inductance
Rg = the air gap reluctance over one pole pitch
Rm = the magnet reluctance
Ni = The MMF source associated with each coil
![Page 25: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/25.jpg)
4.6 Coil Inductance
Letting the outer ring be the reference node, identifying Fr as the center node, and setting the sum of the fluxes leaving the center node to zero
1 2 3 4 0
0r r r r
g m g m g m g m
F Ni Ni F F Ni Ni F
R R R R R R R R
Fr = 0
1 1 1 1g m
Ni
R R
![Page 26: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/26.jpg)
4.6 Coil Inductance
The net flux linked by all four coils
2
1 2 3 4( ) m
g m
N N iN
R R
2m
gg m
N NL
i R R
202 st rog
m
R
L RL N
lg
C
(2 / )
g st p ro
m st ro
A L R
N L R
◄
The air gap inductance is proportional to the rotor surface area
![Page 27: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/27.jpg)
4.6 Coil Inductance
Fig 16. Slot leakage flux
Slot Leakage Inductance
→ Coil current produces a magnetic field that crosses from one side of a slot of a slot to the other.
• This figure depicts a slot in a linear motor.
• This figure includes narrow slot opening between shoes that taper back to the stator teeth
![Page 28: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/28.jpg)
4.6 Coil Inductance
The inductance component that results from the magnetic field that crosses the slot in the y-direction is commonly called the slot leakage inductance.
(2 )( )y
sb s
N i xH x
w d
Where, the slot is assumed to contain two coil sides each having N turns
• The field intensity Hy is zero at the slot bottom because no current is enclosed.
• As x increases, more current is enclosed.
• When all the current is enclosed at x=ds, the field intensity reaches its maximum value equal of Hy=Ni/wsb.
![Page 29: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/29.jpg)
4.6 Coil Inductance
20 (2 )3
s stca
sb
d LL N
w
Where, Lst = the axial length of the slot
Matching this expression to the fundamental relationship Lca=N2P
0
3s st
sb
d LP
w
← Coil areas
← P = the effective permeance of the slot
Including the shoe area → The field intensity is constant over the shoe area
2 0 0 01 (2 )
3 ( ) / 2s st t st sh st
ssb so sb so
d L d L d LL N
w w w w
![Page 30: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/30.jpg)
4.6 Coil Inductance
End Turn Inductance
→ The end turn inductance is created by the magnetic field that surrounds a coil after it leaves one slot and before it enters another slot
Fig 17. Magnetic field about a cylindrical conductor
2
iH
r
20 ln2e
c
l N rL
R
When r>Rc
![Page 31: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/31.jpg)
4.6 Coil Inductance
Fig 17. End turn geometry approximation
20
1 ln4 2cp cp
e
s
NL
A
Where, τcp = the mean coil pitch
r = τcp
As = cross-sectional area
![Page 32: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/32.jpg)
4.6 Coil Inductance
Since there are 2Nm end turn bundles per phase winding and there is no mutual coupling between the end turns of other coils in the same phase, the total end turn inductance per phase is
20 ln2 2
m cp cpe
s
N NL
A
The net phase winding inductance with all coils connected in series is the sum of the three fundamental components,
ph g s eL L L L
![Page 33: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/33.jpg)
4.7 Series and Parallel Connections
• In the preceding sections, back EMF, resistance and inductance were analyzed under the assumption that all coils in a phase are connected in series
• The connection in series is the majority of motor designs
• When all coils are connected in series, the phase back EMF is simply the sum of the individual coil back EMFs.
• When coils are connected in parallel, the coil back EMFs can create circulating currents that contribute to I2R losses but do not provide beneficial torque production.
![Page 34: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/34.jpg)
4.7 Series and Parallel Connections
Fig 18. Two coils connected in parallel
The two inductances and two resistances add, and the two back EMF sources subtract
![Page 35: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/35.jpg)
4.7 Series and Parallel Connections
• The combined back EMF e1-e2 is equal to zero and no current ic circulate around the loop from one coil to the other
• If the individual coil back EMFs are not instantaneously identical, the combined back EMF e1-e2 is nonzero and current ic circulates around the loop independent of any current applied to the parallel coils during motor design
• To avoid circulating currents and their associated loss, only coils having identical back EMFs can be connected in parallel
• For most motor designs this is not possible and therefore parallel-connected coils do not appear often in practice
• In the unusual case when the number of turns cannot be decreased to lower the back EMF amplitude, parallel coil connections must be accepted
![Page 36: Brushless Motor Fundamentals](https://reader036.fdocument.pub/reader036/viewer/2022081520/56814e26550346895dbb8af6/html5/thumbnails/36.jpg)
4.7 Series and Parallel Connections
Fig 19. Coil resistances in series and in parallel
2
/ 1eqp
eqs
R R n
R nR n