BROPGC-AF
-
Upload
rohit-singh -
Category
Documents
-
view
213 -
download
0
description
Transcript of BROPGC-AF
-
PGC-10000-AF is a special configurationof DHIs GPC1 Gas Pressure Controller andRPM4 A70M/A20M Reference PressureMonitor(see the GPC1 and RPM4 brochures fordetails). The PGC-10000-AF was designed tooptimize the testing and calibration of analogand digital pressure gauges and indicators inranges from less than 500 psi (3.5 MPa) to10 000 psi (70MPa). This special configurationwasselectedbytheUnitedStatesAirForceasthenext generation high pressure pneumatic gaugecalibrationsystemfordeploymentinitsPrecisionMeasurement Equipment Laboratories (PMELs)throughouttheworld.
WithGPC1andassociatedGB-152GasBooster,the operator effortlessly generates and adjustspressuretosetthedeviceundertesttoitscardinalpoint. The RPM4 then precisely measures theactualpressureapplied.
Interactive RPM4 embedded software auto-maticallysetsup thecalibrationprocedurebasedon entry of the DUT full scale and tolerance. Itthen steps the operator through the test, loggingdata andproviding real timenotificationof inorout-of-tolerance conditions at each point. A footpedal ENTER switch allows the operator totriggerreadingshandsfree.
Calibrate any range device in gas from less than 500 to 10 000 psi (70 MPa) FS with one compact, integrated system
Effortless operation; no pumping, no weight lifting
Includes gas booster to boost a bottled air supply as low as 400 psi (2.75 MPa) to 10 000 psi (70 MPa)
Easily set pressure to DUT cardinal point and read back actual pressure from the reference
On-board calibration routines with real time out-of-tolerance notification and data logging
Foot pedal ENTER key for hands free sequence execution
Complete a typical high pressure gauge run in about 20 minutes (20 % ascending increments)
Supports 12 units of measure and custom units
Push button switching between gauge and absolute measurement modes
RS232 and IEEE-488 interfaces included; compatible with COMPASS for Pressure software
Delivered with connectors and adaptors for NPT, AN4 and gland and collar DUTs
Includes molded, reusable transit case for shipping RPM4/HPMS transfer standard for recalibration
PneumaticGauge Calibrator
FEATURES DESCRIPTION / APPLICATIONS
-
2005 DH Instruments, Inc. Printed in USA Bro. No. 5080.3.A.1
ORDERING INFORMATION
Operationandmaintenancemanuals
A2LAaccreditedcalibrationreport
Systemfinaltestreport
ProductDesignator: PGC-10000-AF
PartNumber: 402205
OrderingDescription: Pneumaticgaugecalibrator
PGC-10000-AFisaturnkeysystemdeliveredcompletewith:
GPC1-10000-AFPneumaticPressureController
RPM4/HPMSA70M/A20MReferencePressureMonitor
GB-152-AFGasBooster
Interconnectinghardware
Testconnectionadaptorkit
MoldedtransitcaseforRPM4/HPMS
Due to a policy of continuous improvement, all specificationscontainedinthisbrochurearesubjecttochangewithoutnotice.
PGC-10000-AF,PGC1,RPM4,GB-152andCOMPASSaretrademarks,registeredandotherwise,ofDHInstruments,Inc.
DH Instruments, Inc.4765 East Beautiful LanePhoenix AZ 85044-5318USA
Tel 602.431.9100Fax 602.431.9559
SPECIFICATIONS
GENERAL PowerRequirements:
Electrical 85to264VAC,50/60Hz,25VAmaxconsumptionand12VDC,1.2A
Pneumatic 75psig(500kPa)shopairat15to75scfm (425 to2125slm)and100psig(700kPa)clean,drygas
TestGasSupply:
400 to 3 000 psi (3 to 20 MPa)Maximumhighpressureoutputishighpressuresupplytimes25
OperatingTemperature Range: 18to28C(64to82F)
Weight:
RPM4/HPMS 11.0kg(22lb)
GPC1 24.0kg(53lb)
GB-152 16.4kg(36lb)
Total 51.4kg(113lb)
BenchtopSystemFootprint(GB-152GasBoostermountedunderbench): 75cmWx60cmD(30in.x24in.)
OverallPressureRange: Gaugemode:0to10000psig Absolutemode:atmto10000psia
(70MPa)
StandardTestFluid: Anynon-corrosivegas
TestConnection: DH500(glandandcollartypeforconedandlefthandthreadedtubeequivalenttoAEF250C,HIPHF4,etc.),adaptorsto1/8in.NPTM,1/4in.NPTM,1/4in.NPTF,AN4Mprovided
PRESSURERANGES(Allrangesaregaugeandabsolute.) HiQ-RPT 10000psi(70MPa)
LoQ-RPT 3000psi(20MPa)
PRESSUREMEASUREMENT Precision1:
HiQ-RPT1 0.0175%ofreadingor0.44psi(3kPa),whicheverislarger
LoQ-RPT 0.0175%ofreadingor0.13psi(0.9kPa),whicheverislarger
OperatingTemperature Range:18to28C
PredictedStability2: 0.004%ofreading
MeasurementUncertainty3:
HiQ-RPT 0.02%ofreadingor0.5psi(3.5kPa),whicheverislarger
LoQ-RPT 0.02%ofreadingor0.15psi(1kPa),whicheverislarger
1. Precision:Combinedlinearity,hysteresis,repeatability.
2. Stability:Changeinzeroandspan,withuseofAutoZfeature,over6monthsperiodfortypicalRPTusedundertypicalconditions.AsstabilitycanonlybepredictedandvariesfromQ-RPTtoQ-RPT,stabilityforaspecificQ-RPTshouldbeestablishedfromexperience.
3. Maximumdeviationof theQ-RPTindicationfromthetruevalueofappliedpressureincludingprecision,predictedoneyear stability, temperatureeffectandcalibrationuncertainty (assumescalibration reference uncertainty of 0.005% of reading), combined and expanded (k=2)followingtheISOGuidetotheExpressionofUncertaintyinMeasurement..
Pneumatic Gauge Calibrator