Boq Tnhb Ongc Chennai

7/30/2019 Boq Tnhb Ongc Chennai

http://slidepdf.com/reader/full/boq-tnhb-ongc-chennai 1/2939

Sl. NoTNBP/

NBC No.Description of item/Work Unit QTY

CIVIL WORKS

PILE WORKS

1 BORED PILE WORKS (Cast in Situ)

30A Mobilisation of pile rig and its related equipments,bringing into site of all plant and machinery along withaccessories etc.. including transportation and installationof vertical cast in situ bored piles of following diameterusing reinforced cement concrete Design Mix M30 Gradeby setting the bored cast in situ pile equipments with allaccessories and tools at each locations based on thesequence of operations as directed by the Engineer-in-charge., boring for the piles from ground level in all soilsto the required depth below cut off level to carry a safeworking load not less than specified, by Direct Mud

Circulation Method ( using bentenite clay of required

density) inclusive of pile accessories, temporary casingpipe, bentenite solution of 10% of concrete with requireddensity and routine test as per IS 2911 (Part- IV) -1985 etc.complete as directed by the Engineer-in-charge..

excluding the cost of steel and fabrication reinforcementgrills but including Bentenite solution to carry safeworking load not less than specified, machinery charges,labour charges and assembling, erecting the equipmentand dismantling, trimming the pile concrete above cutofflevel, cleaning the debris & slushy, carting away thesurplus from the site inclusive of loading and unloadingof transportation, the cost of shoe and the length of the

pile to be embedded in the pile cap and removal of plantand machinery from site after completion of work. etc.,allcomplete, complying with relevant standard specificationand as directed by the Engineer-in-charge.. (Pile shall bemeasured from the top of the shoe to the bottom of thepile cap.)

Design Mix M30 Grade concrete should be prepared withordinary Portland Cement with water cement ratio notexceeding 0.45 including the use of Plasticizer of requiredGrade and Hard Broken Granite Stone Jelly of 20mm sizeand down graded as per requirement. Mix Design Datahas to be got approved by the Engineer-Incharge beforecommencement of work.

a 500mm dia pile of 98 MT safe load RMT 10419

b 600mm dia pile of 141 MT safe load RMT 6210

c 750mm dia pile of 220 MT safe load RMT 1380

ons ruc on o u s or es es en a a s an ce omp ex or a nnanagar es ern



2 Vertical load testing of piles in accordance with IS 2911 (part iv) including installation of loading platform andpreparation of pile head or construction of test capand dismantling of test cap after test etc, as perspecification and as directed by the Engineer-in-charge...

Initial test

a upto 100 tonne capacity pile. Nos. 5

b Above100 tonne and upto 200 tonne capacity pile. Nos. 5

c Above200 tonne and upto 400 tonne capacity pile. Nos. 1

Total of Bored Pile Works

EARTH WORK EXCAVATION

3 23 V, VIS2

Earth work excavation for foundation in all type of soilsand sub soils to the required depth as may be directedincluding dense soil, disintegrated/weathered/soft rocknot requiring blasting for Footings of columns, Pile capsand hydrant trenches, catch basins,collection chambers,boundary walls, security cabins, rainwater harvestingpit,Tennis court etc.including manual excavation forlevelling, dressing of sides and ramming of bottom withall leads and lifts,shoring,strutting and bailing out waterwherever necessary etc.all complete as directed byEngineer-Incharge.

a 0 to 2m depth. Cum 8786

b 2 to 3m depth. Cum 203

4 23 & 24 V,VI S2

Earth work excavation in open excavation in all type ofsoils including stiff clay for UG Sump. STP etc.,includinglevelling, dressing of sides and ramming of bottomwith all leads and lifts, shoring, strutting and bailing outwater wherever necessary etc.. all complete as

directed by Engineer-Incharge.

a 0 to 2m depth. Cum 1100

b 2 to 3m depth. Cum 550

c 3 to 4m depth. Cum 550

d 4 to 5m depth. Cum 550

e 5 to 6m depth. Cum 447

f 6 to 7m depth. Cum 1100



5 24 & 25 V,VIS2

Supplying and filling in foundations and the areawherever specified with approved good quality fillingmaterials in plinths, area development etc. whereverspecified in layers of not exceeding 150 mm thickincluding breaking clods,storing,transportation ,doublehandling, watering, compacting each layer with vibratorycompactor and at un-accessible places with wooden/steelrammers to achieve 95% proctor density at optimummoisture content, all leads and lifts, bailing/ pumping outof water to keep site dry while backfilling; cost shallinclude conveyance of all materials, labour, machineryetc. complete as directed.The rate to includes loading,unloading, hire and fuel charges for tools and plants andother incidental charges etc., as complete with all respectscomplying with relevant standard specification, asdirected by the Engineer-in-charge.

a Approved quality gravel Cum 9888

b Approved quality river sand Cum 744

c Quarry dust Cum 11340

d Filling with excavated earth with necessary ramming Cum 36006 Carting away surplus earth/excavated material/debris

and like materials outside the site and disposing off thesame to the outside the city limit as directed by theEngineer-in-charge for dumping of suchmaterial,including spreading etc.,as per the norms by thelocal authorities.

Cum 7478

Total of Earth work Excavation Works

ANTI-TERMITE TREATMENT

7 Providing Pre - construction Anti - termite treatment andcreating a chemical barrier to the building by injectingchemical emulsion of required concentration under grade

slab and grade beam, all round the Pile Caps, Catchbasins, trenches, pits, tunnels, wall trenches, back fill,plinth filling, junction of wall and floor. Externalperimeter of building, surrounding of pipes, expansion joints, below U.G. sump and retaining/side walls etc. asper instructions of chemical manufacturer as directed bythe Department officer/ Architect. The treatment shall becarried out strictly in accordance with the technicalspecification and conforming to IS 6313 or equivalent BSspecification. The chemical to be used as insecticide forthe treatment shall be Biflex Tc, TC stands for TermiticideConcentrate for Termite Control (Bifenthrin) and theapplication shall be diluted 1 part of chemical Biflex Tc

with 49 parts of water to get 0.05% emulsion and strictlyin accordance with the manufacturer‟s specification.



The work should be carried out by an approved andregistered specialist pest control agency only. Tenderer tofurnish the name of the proposed specialist firm. A 10years post application guarantee against defects shall befurnished by the main Contractor. Note : Horizontal planarea at ground floor level of the building will be measuredand paid.The chemical to be used for the treatment andconcentration of the chemical solutions should be as laiddown in IS - 6313 Part II.as directed by the Engineer-in-charge.

Sqm. 5115

Total of Anti Termite Works

CONCRETE WORKS

8 28 V, VIS2 (SS.A)

VII

Providing and laying plain cement concrete 1:5:10 (1 ofcement : 5 of course sand : 10 of hard broken stone jelly )using coarse graded aggregate of 40 mm for levellingcourse under floors ( Ground Floor level ) etc. includingform work wherever necessary and well compacted etc.all complete, as directed by the Engineer-in-charge...

Cum 421

9 28 V, VIS2 (SS.A)

VII

Providing and laying plain cement concrete 1:4:8 (1 ofcement : 4 of course sand : 8 of hard broken stone jelly)using coarse graded aggregate of 40 mm for levellingcourse under pilecaps, steps, walls, platform etc.including form work wherever necessary and wellcompacted etc. all complete, as directed. and as directedb the En ineer-in-char e..

Cum 210

10 28 V, VI(S2) (S5A)

VII

Providing and laying P.C.C. 1:3:6 (1 of cement : 3 ofcourse sand : 6 of hard broken stone jelly ) of specifiedthick wherever specified using river sand, 20mmincluding base reperation, Compaction, levelling fordrains, trenches and collection chamber all leads and lifts,curing for all structures at all locations etc., Complete

.(Footings)s and as directed by the Engineer-in-charge..

Cum 747

Total of Concrete Works

REINFORCED CEMENT CONCRETE (RMC)

DESIGN MIX CONCRETE

NOTE: RMC SHALL BE PROCURED FROM SITE

BATCHING PLANT



11 Cement Concrete M30 Design Mix for all reinforcedcement concrete works namely Pile cap,Grade beam, RaftSlab,Retaining walls,Shear wall,RCC walls,Liftwalls,Plinth beams, Column,Column footings,Gradeslab,Roof slab & beam,Curved beams, Grid beams,Flatslab / Column drops,Pergola,Staircase waist and landingslab lintel, Sunshades, parapet cum drops, Steps,canopy,fin projects, window boxing slab, Loft,chajjas,Planterbox,Deck slab and other similar works and other similarstructures etc..using ordinary Portland cement of grade 53from approved manufacturer, river sand, 20mm anddown size coarse aggregates, necessary approvedadmixtures as per requirement and using fly ash contentnot excedding the 15 % in structural and non structuralworks excluding the cost of reinforcement grills,fabrication charges, shuttering and centering butincluding all leads and lifts,pumping using line pump orboom placer,

scaffolding wherever necessary,laying,vibrating,

finishing, curing etcall complete complying with relevant standardspecification & as directed by the Engineer-in-charge..Mix Design Data has to be got approved by the Engineer-in-charge. before commencement of work. etc. complete

(Design mix shall be as approved by the Engineer-in-

charge.)

M30 GRADE (Structural Concrete)

a In Foundation and Plinth

i Upto 1.5 M depth Cum 4451

ii From 1.5 M to 4.5 M depth Cum 396

iii From 4.5 M depth to 9 M depth Cum 97b Ground/Stilt Floor Cum 1527

c First Floor Cum 1478

d Second Floor Cum 1258

e Third Floor Cum 1127

f Fourth Floor Cum 428

g Fifth Floor Cum 298

h Sixth Floor Cum 298

i Seventh Floor Cum 298

j Eighth Floor Cum 298

k Ninth Floor Cum 298

l Tenth Floor Cum 298

m Eleventh Floor Cum 298n Twelfth Floor Cum 300

o Thirteenth Floor Cum 205

p Fourteenth Floor Cum 195

q Fifteenth Floor Cum 195

r Sixteenth Floor Cum 195

s Seventeenth Floor Cum 198

t Eighteenth Floor Cum 122

u Terrace Floor-1 Cum 76



v Terrace Floor-2 Cum 68

12 Supplying and fixing of Precast slab for the followingthickness made in CC 1:1.5:3 (One cement, one and halffine aggregate and three coarse aggregate) using 12mmsize hard broken stone jelly including the cost of slab,moulding, laying,finishing smooth 6mm thick cementplaster 1:3 (one cement and three fine aggregate) onexposed surfaces, curing, transportation, pointing, andalso include for providing necessary MS angles ofrequired size based on the thickness of precast slab and tobe fixed on the edges of the precast slab includinggrouting the lugs with Cement concrete 1:1.5:3, forapproach slab and other similar works but excluding costof reinforcement and as directed by the Engineer-in-charge..

a 100mm thick Precast slab Sqm. 720

b 75mm thick Precast slab Sqm. 379

13 Providing, precasting and placing to the requiredgradient, M25 grade precast Concrete cover slab of 50mm

thick with perforation of size as specified in drawingsover storm water drain / trenches / ducts / pulloutchambers etc., as per the drawing includingreinforcement, addition of polypropelene fibers, casting inyards, curing, edge protection of all edges using ISA25x25x4, finishing all surfaces with all leads and lifts,transportation, placing, cost of PVC sleeves, MS hooks,finishing the joints with CM 1:3 curing etc., complete asdirected by Engineer-Incharge.

Sqm. 1971

14 Providing and fixing reinforcement for RCC work withThermo Mechanically Treated Bars (TMT) or equivalentHYSD bar of various diameters and grade of steel

conforming to IS 1786 latest version specificationincluding cutting and waste, bending, hoisting,fabricating and placing in position according to drawingsand binding the reinforcement with 18 gauge double foldGI binding wire and providing precast cement concrete /approved PVC cover blocks for placing thereinforcements in position and for maintaining the coverspecified and / or according to relevant IS codes.Rate toinclude transport from the plant to site of work etc.,complete as directed by the Engineer-in-charge..



Note : Unless noted otherwise the measurements inaccordance with IS 1200. However reinforcement shall bemeasured only in lengths of bars as actually placed inposition on standard weight basis, no allowance beingmade in the weight for rolling margin. Authorised lapsand splices only will be measured. Chairs of any shape &profile, Spacer bar of any shape & profile, cover block,wastage and binding wire will not be measured and shallbe included in the quoted rates. Quoted rate shall bedeemed to have considered the above stipulation. Quotedrate to include lead, lift, placing at all levels and asdirected.

a Grade of reinforced steel - Fe 500 - TMT bars MT 2925

Total of RCC Works

FORM WORK

15 Supplying and erecting centering for sides and soffitsincluding supports and strutting up to 3.30 m height withall cross bracing for plane surfaces as detailed below,using mild steel sheets of 90 X 60 cm 10 gauge stiffened

with MS angle of 25 X 25 X 3mm for boarding, laid overadjustable span & jacks and supported by 50mm dia pipesfor general pipes scaffolding systems @ a spacing of 1.20mc/c and vertical connected at a height of 2.0m c/cincluding 'C' & 'U' clamps and base receiver cup at bottomfor connecting pipes etc and removable systems etccomplete.

a 30(S) 86 86A V, VI(S3) VII

All reinforced cement concrete Footings, plinth beam, pilecap, staircase steps, sill beam, grade beams & slab etc.

Sqm. 9920

b Columns,(Rectangular/Square) chajjas, loft andsunshades etc for all floors

Sqm. 22708

c Lintels, conventional slab & beams, staircase waist slab &landings, pergolas, etc for all floors

Sqm. 42757

d Walls (any thickness) including, core walls, shear wall,retaining wall, parapet wall etc. for all floors.

Sqm. 3648

16 Extra for additional height in centering, shutteringwherever required with adequate bracing, propping etc.including cost of de-shuttering and decentring at alllevels, over a height of 3.30m ( height shall be thedimension as measured from the top of the lower slab /pcc sub base to the bottom of the subsequent upper slab /soffit of the beam as the case may be.) , for every

additional height of 1m or part thereof for: (Plan area tobe measured). Suspended floors, flat slabs, drops, posttensioned slabs, slabs curved in plan to any radius, gridslab, roofs, landings, beams including spiral and curvedbeams of all radius, post tensioned beams, grid beams,plinth beams, girders, bressumers, cantilevers andbalconies.

Sqm. 11153

Total of Formwork Works

MASONRY WORKS



17 31 &similar to31C V, VI(S5) VII

Brick work with II class ground moulded well burntchamber bricks of size 9"x4-1/2"x3" (23x115x7.5 cm)withminimum compressive strength of 50 Kg per Sq.cm. incement mortar 1:5 (1cement : 5 coarse sand) etc. completeand as directed by the Engineer-in-charge.. - ForFoundation and Basement

Cum 906

18 31 &similar to31C V, VI(S5) VII

Brick work with II class ground moulded well burntchamber bricks of size 9"x4-1/2"x3" (23x115x7.5 cm) withminimum compressive strength of 50 Kg per Sq.cm. incement mortar 1:6 ( 1cement : 6 coarse sand) forsuperstructure at all levels etc. complete and as directedby the Engineer-in-charge..

a Ground/Stilt Floor Cum 58

b First Floor Cum 40

c Second Floor Cum 33

d Third Floor Cum 33

e Fourth Floor Cum 33

f Fifth Floor Cum 35

g Sixth Floor Cum 35

h Seventh Floor Cum 35

i Eighth Floor Cum 35

j Ninth Floor Cum 35

k Tenth Floor Cum 35

l Eleventh Floor Cum 35

m Twelfth Floor Cum 26

n Thirteenth Floor Cum 26

o Fourteenth Floor Cum 26

p Fifteenth Floor Cum 26

q Sixteenth Floor Cum 30

r Seventeenth Floor Cum 13

s Eighteenth Floor Cum 15

19 35-J&K Providing and constructing Cement Concrete Solid BlockMasonry in cement mortar 1:5 ( one cement and fivecoarse sand ) 190mm thick for Foundations using precastmachine moulded blocks using standard size of 390 x 190mm of solid cement concrete blocks with minimumcompressive strength of 5N / Sq.mm conforming to IS2185 or equivalent BS including all scaffolding, staging,curing, and all leads etc. complete and as directed by theEngineer-in-charge..

Sqm. 188

20 35-J&K Providing and constructing Cement Concrete Solid Block

Masonry in cement mortar 1:6 ( one cement and fivecoarse sand ) 190mm thick for Super structure in thefollowing floors using precast machine moulded blocks atall levels using standard size of 390 x 190 mm of solidcement concrete blocks with minimum compressivestrength of 5N / Sq.mm conforming to IS 2185 orequivalent BS including all scaffolding, staging, curing, alllifts and leads etc. complete and as directed by theEngineer-Incharge.

a Ground/Stilt Floor Sqm. 1859

b First Floor Sqm. 913

c Second Floor Sqm. 976



d Third Floor Sqm. 650

e Fourth Floor Sqm. 382

21 Providing and constructing Cement Concrete Solid BlockMasonry in cement mortar 1:5 ( one cement and fivecoarse sand ) 90mm thick in the following floors usingprecast machine moulded blocks at all levels usingstandard size of 390 x 190 mm of solid cement concrete

blocks with minimum compressive strength of 5 N/Sq.mm conforming to IS 2185 or equivalent BS includingall scaffolding, staging, curing, all lifts and leads etc.complete and as directed by the Engineer-in-charge.





22 Providing and constructing Glass Block masonry work atall levels in Fire escape staircase wherever necessary (asper drawing), to be set in sealent of approved qualityusing standard size of 190x190x80 mm of Glass Brick of

approved vendor of approved by Engineer-in-charge /Consultant, manufactured as per Manufacturer'sspecification etc.. Rate shall include accessories forsupporting the system Polystyrene foam over an ezylayframe, Acc-Speed jamb connectors and straightconnectors, galvanised reinforced rods and necessarystaging and scaffolding arrangement, verticality (Plumblevel) of the walls, Skilled labour,loading and unloading,lead & Lift, Tools & Plants, Finishing and curing etc. ascomplete in all respects complying with relevant standardspecifications and as directed by the Engineer-in-charge..

Sqm. 116

23 31c Providing and constructing 115 mm. thick, masonry wall,at all levels, with approved best quality well chamberburnt moulded bricks(230X115X75mm), with minimumcompressive strength of 50 Kg / Sq.cm, in Cement Mortar1:4 with M20 reinforced cement concrete binders - 80 mmthick, using coarse graded aggregate of 12 mm and down-size, reinforced with 4 nos. of 8 mm dia. Fe-500 grade steel-and 6 mm dia. Mild steel stirrups at 200 mm c/c, andbinders placed at 2 M intervals. Rate shall include for costof reinforcements and tying in postion using binding wiremade out of 18 gauge G.I. annealed only or 18 gauge S.S.,form work, scaffolding, raking out joints, curing etc

complete as directed by the Engineer-in-charge..






f Fifth Floor Sqm. 17



g Sixth Floor Sqm. 17

h Seventh Floor Sqm. 17

i Eighth Floor Sqm. 17

j Ninth Floor Sqm. 17

k Tenth Floor Sqm. 17

l Eleventh Floor Sqm. 17

m Twelfth Floor Sqm. 17

n Thirteenth Floor Sqm. 17o Fourteenth Floor Sqm. 17

p Fifteenth Floor Sqm. 17

q Sixteenth Floor Sqm. 23

r Seventeenth Floor Sqm. 9

s Eighteenth Floor Sqm. 24

24 Providing and constructing Autoclaved Cellular

(Aerated) Concrete Blocks work at all levels, in cementmortar 1:4 using standard size of 400 x 200 mm , as perapproved manufacturer's specification etc. complete andas directed. Blocks manufactured under strict qualitycontrol conditions confirming to IS 2185 - Part - 3 latest

version shall be used. Rate shall include the following:

a) Fixing the panels at all levels and supported on slabsoffit with suitable arrangement including necessarystaging, scaffolding arrangement, alignment andverticality (plumb level) of the walls. Rate Shall alsoinclude cutting necessary grooves / chases of requiredsize and at required height for concealing electrical,plumbing, conduits / pipes, holdfasts, bolts etc. andmaking good surfaces after concealing is complete.

b)Grouting of cores in blocks to complete course for fixing

of frames and all joinery works etc complete, as directed.All materials required to carry out all related worksincluding specialised work required around and aboveopening to receive the Frame and to ensure that the loadof the panels are not transferred on to the frames orshutters of the doors, windows and ventilators so as toavoid bending of door frames/shutters and affecting theopening / closing operation of the door shutter. etccomplete and as directed.

c) Finished work should be sand papered to receiveplaster and any unevenness or undulations on the blockshould be made good by the application putty

) If required to do so the test at an approved laboratory toensure the compression strength of blocks confirming toIS standardsRate shall include accessories for supporting the systeminto the ceiling with cleats & Anchor fasteners,scaffolding, loading and unloading, lead & Lift, Tools &Plants etc. complete and as directed.

i Autoclaved Cellular (Aerated) Concrete Blocks wall of

200 mm thick











i Eighth Floor Sqm. 754 j Ninth Floor Sqm. 754




n Thirteenth Floor Sqm. 487

o Fourteenth Floor Sqm. 407





t Terrace Floor-1 Sqm. 262u Terrace Floor-2 Sqm. 323

ii Autoclaved Cellular (Aerated) Concrete Blocks wall of

100 mm thick









i Eighth Floor Sqm. 281 j Ninth Floor Sqm. 281




n Thirteenth Floor Sqm. 277

o Fourteenth Floor Sqm. 277





t Terrace Floor-1 Sqm. 3



25 Extra rate over & above Solid Masonry wall for providingR.C.Binder - 80 mm thick with M20 reinforced cementconcrete using coarse graded aggregate of 12 mm anddownsize, reinforced with 4 nos. of 8 mm dia. Tor steeland 6 mm dia. Mild steel stirrups at 200 mm c/c andbinders placed at intervals not more than 1000 mm,including cost of reinforcements and tying in positionusing binding wire made out of 18 gauge GI annealedonly or 18 gauge SS, form work, scaffolding, all labour,hire and fuel charges for all tools and plants employedand all other incidental charges etc. all complete, asdirected by the Engineer-in-charge.

a Solid block wall of 200mm thick for all floor. Rmt 17837

b Solid block wall of 100mm thick for all floor Rmt 4929

Total of Masonry Works

IRON AND STEEL WORKS

26 86 & 86A Supply and fixing in position Hot rolled structural steelMembers / Sections at all levels and to any shape &profile consisting of MS joists, channels, angles, purlins,

runners, insert plates, flats and sag rods with necessarysleeves, bolts and nuts, gratings, pipes including cutting,straightening, welding as per standards for connectionsincluding consumables etc.complete. Rate shall includepreparation of surface, All MS members shall be paintedwith anti corrosive, low VOC PU paint (metallic finish)with compatible primer to a minimum film thickness of 75microns and 2 coats of low VOC PU paint and total dryfilm thickness 225 microns etc. all complete, as directed bythe Engineer-in-charge..

MT 260

27 Providing and fixing in position Hot rolled structural steelMembers / Sections at all levels and to any shape &profile consisting of MS joists, channels, angles, purlins,runners, insert plates, flats and sag rods with necessarysleeves, bolts and nuts, gratings, pipes including cutting,straightening, welding as per standards for connectionsincluding consumables etc.complete. Rate shall includepreparation of surface, applying two coats of Zincchromate/Phosphate primer before and after erection andtwo coats of first quality synthetic enamel paint ofapproved make after erection, sand blasting etc. complete,as directed by the Engineer-incharge.

MT 42



28 86 & 86A Supplying, fabricating and placing in positionM.S.chequered plate of required thickness for duct

closing and shafts closing at all floors at all levels withnecessary supports such as M.S. angles/M.S. flatsincluding stiffeners to be placed on angle iron framework. (Frame work, angles, stiffeners will be measuredunder relevant structural steel item). Rate shall includemaking necessary cutouts for inserts, All MS membersshall be painted with anti corrosive, low VOC PU paint(metallic finish) with compatible primer to a minimumfilm thickness of 75 microns and 2 coats of low VOC PUpaint make and total dry film thickness 225 microns. etcall complete complying with relevant standardspecifications & as directed by the Engineer-Incharge.

MT 30

29 86 & 86A Providing and fixing welded M.S. grills to the window

openings,along the compound wall details as per drawingwith necessary screws, bolts and fixed with necessaryM.S. lugs embedded in masonry with C.C. 1:2:4 andfinishing the surface neatly. Rate shall include for two

coats of first quality synthetic enamel paint over a coat ofzinc phosphate primer, necessary tools & plants, weldingand consumables, etc. complete, as directed. Design ofgrills and the size of members to be used shall be gotapproval before put into use & as directed by theEngineer-in-charge.

MT 60

30 84A Supplying and fixing Motorised rolling shutters fromapproved fabricator as per IS 6248 made out of electrogalvinized/ galvolume laths of 75 x 1.20 mm size dulyinterlocked together through their entire length includingperforated galvolume lath strip at 1000mm lenght fromstandard eye level in the amid of shutter and jointedtogether at the end by end locks mounted plate witharrangements for inside and outside locking with pushand pull operation, suspension pipe shaft roller steel pipeconforming to heavy duty as per IS 1161 shall be designeddeflection shall not be exceed 5mm per 1m width withM.S. brackets plate size not less than 450 x 450 x 6 mm,M.S. side guide channel thichness shall not be less than3.14mm with necessary depth as per IS 6248. Rateincluding the cost of providing and fixing necessary goodquality high tensile steel wire springs.

Rate including 0.9mm thick GI sheet top cover. Rate

includes one coat of grey epoxy primer and automationsystem comprising of side one operator with manualchain override in case of power failure and key selectoretc.. all complete as directed by Engineer-Incharge.

Sqm. 72



31 Supplying and fixing in position of M20 grade 2.28m longRCC precast concrete struts of size 150 mm x 150 mm and125 mm x 125 mm for bottom and top respectively usingand 20 mm and down graded metal for Chain link fencingincluding necessary shuttering for precasting, oiling,concreting and removing, curing appropriately, includingthe cost of fabricating and fixing of reinforcements 4 nosof 8 mm dia as main rods and 8mm dia stirrpus at 150mm ctc. The struts are to be laid in position vertically ordiagonally as shown in drawing. The rate shall includethe cost of conveyance, material, labour and duties , taxesetc all complete as directed by Engineer-Incharge.

Nos 426

32 Providing, supplying and fixing GI Chain link 50 x50mm using 10 gauge with posts of specified material andof standard design placed steel wire fabric fixed betweenthe posts fitted and fixed with G.I. staples / G.I Boltscomplete all as per specifications and drawings and asdirected at site.

Sqm. 614

33 Providing and fixing pre-polished Stainless steel railingusing 50mm dia bent to shape as shown in drawing and32mm dia for vertical and 25mm dia three bracing bar asper drawing. Rate shall be inclusive of fixing the railinginto the concrete surface with necessary hardware's, SScaps, grouting for the same etc. complete.(forstaircase,balcony,open to sky) and as per drawing SS shallconforming of grade AISI 304.etc. all complete, as directedby the Engineer-in-charge

Kgs 11725

34 Providing and fixing of GI hand railing , in general it shallbe made with 50mm dia bend to shape as shown indrawing fixed at top and three 25mm dia pipe for bracing

bar as per drawing. Vertical post shall be 32mm dia Rateshall be inclusive of fixing the railing into the concretesurface with necessary hardware's, GI caps, grouting forthe same etc. complete. The rate shall be inclusive offinishing the GI surfaces with Duco paint of approvedcolor to the required level after the base prepration(forstaircase height 1050mm) etc. all complete, as directed bythe Engineer-in-charge

Rmt 939



35 86,86A Supplying, fabricating, erecting and fixing in positiongates , bottom rail for gates, monkey ladders and allmiscellaneous steel works as shown in the drg. or asdirected by the Engineer at all heights and depths aboveand below finished floor level using MS angles channels,rails, tees, plates, flats, rounds, squares etc., of varioussizes and other structural steel sections including,straightening, cutting, fabricating, welding, bending toshape bolting, fixing in position, welding to insert plateembedded in concrete and inclusive of the followingfinishes : I) Sand blasting as specified ii) 2 Coats of epoxypaint over one coat of red oxide primer. etc. all complete,as directed by the Engineer-in-charge

MT 4

Total of Iron & Steel Works

FLOORING WORKS

36 28 & 39 H Providing and laying in panels not more than 20 sqm. inplan granolithic flooring with cement concrete 1:2:4 byusing coarse graded aggregate of 6 to 12 mm size laidmonolithic with floor concrete and finished smooth with

power trowel including preparation of concrete surfaceand form work. The screed shall be laid for effectiveseparation of panels not exceeding 20 sqm. in plan etc.complete as per Specifications and as directed.Unevenness in floor finish shall not exceed +2mm in onesquaremetre area. Rate to include lead , lift at all levels,pumping, placing, necessary formwork, curing etc., allcomplete, as directed by the Engineer-in-charge

a 50 mm thick. Sqm. 3241

b 40 mm thick. Sqm. 1255

37 Providing and laying self levelling epoxy of 1000 micron

thick joint less floor topping from approved make,application over the granolithic flooring as per approvedmanufacturer's specification, including preparation ofsurface, application, wastage, equipment, tools andplants, work at all levels etc. complete as directed by theEngineer-in-charge..

Sqm. 777

38 Providing flooring with best quality approved make White ceramic tiles ranges, Size of tiles shall be 6mmthick of 305 x 305 mm size set in CM 1:4, 20mm thick andpointing the joints with Laticrete and pointing withLaticrete of approved make and as directed. Rate shallinclude for preparation of base surface, and finishing thesurface, cleaning the surface, and protecting and with

Gypsum / POP layer over Plastic sheet and removing thesame before handing over, work at all levels etc. ascomplete in all respects and complying with relevantstandard specifications and as directed by the Engineer-in-charge..( Over Head Tanks & U.G.Sump)

Sqm. 715



39 39A Providing and fixing wall dado with best qualityapproved make White Glossy ceramic tiles ranges, sizes150 x 150 mm x 6 mm thick set in CM 1:2, 10mm thick andpointing with white cement and as directed. Rate shallinclude for preparation of base surface, and finishing thesurface, cleaning the surface, work at all levels etc. ascomplete in all respects and complying with relevantstandard specifications and as directed by the Engineer-incharge.( Over Head Tanks & U.G.Sump)

Sqm. 1158

Total of Flooring Works

INTERNAL & EXTERNAL FINISHES

40 56&57 Plastering to R.C walls, slabs, peripheral beams andcolumns with Cement Mortar 1:3,(1cement : 3 fine sand)10 mm thick according to the specification. Rate shallinclude for necessary hacking,staging,scafolding andcuring at all levels and elevations etc.complete as directed.and as directed by the Engineer-incharge.

Sqm. 26204

41 56&57 Plastering for external surfaces with 12 mm thick in

Cement Mortar 1:5 (1 cement : 5 fine sand ) and asdirected. Rate shall include for include for providing andfixing of GI plastermesh and corner bead inludingnecessary hacking,staging,scafolding and curing at alllevels and elevations and for providing drip bands /moulds / grooves to any size and shape as directed by theEngineer-in-charge..

Sqm. 81634

42 63 Applying white washing three coats to ceilings and wallswith pure shell lime or fat lime conforming to IS-712 all asper Specification including cost of lime, brush etc..complying with relevant standard specification, asdirected by the Engineer-in-charge. .

Sqm. 11741

43 Providing and applying External texture paint ofapproved colour and Granito Spray (1947) of Spectrumpaints or equivalent approved make . Rate shall includesurface preparation, with two coats of primer and 2 coatsof natural granite based approved Granito Spray (Greycolour) Paint followed by two coats of silicon based clearcoat for excellent weatherability and contrast grooves asper manufacturer specification with necessarystaging,scaffolding etc..as complete in all respectscomplying with relevant standard specifications and asdirected by the Engineer-in-charge..

Sqm. 7037



44 Providing and applying External texture paint ofapproved colour and Granito Smooth (1901) of Spectrumpaints or equivalent approved make . Rate shall includesurface preparation, with two coats of primer and 2 coatsof sand,silica and mica based approved Texture Paintfollowed by two coats of silicon based clear coat forexcellent protection and weatherability and contrastgrooves as per manufacturer specification with necessarystaging,scaffolding etc..as complete in all respectscomplying with relevant standard specifications and asdirected by the Engineer-in-charge..

Sqm. 645

45 Providing and applying External texture paint ofapproved colour and Rustic fine (1004) texture ofSpectrum paints or equivalent approved make . Rate shallinclude surface preparation, with two coats of primer and2 coats of approved Texture Paint followed by two coatsof silicon based clear coat for excellent protection andweatherability and contrast grooves as per manufacturerspecification with necessary staging,scaffolding etc..as

complete in all respects complying with relevant standardspecifications and as directed by the Engineer-in-charge..

Sqm. 8058

46 Providing and applying External texture paint ofapproved colour and Spray coat bubble (1018) texture ofSpectrum paints or equivalent approved make . Rate shallinclude surface preparation, with two coats of primer and2 coats of approved Texture Paint followed by two coatsof silicon based clear coat for excellent protection andweatherability and contrast grooves as per manufacturerspecification with necessary staging,scaffolding etc..ascomplete in all respects complying with relevant standard

specifications and as directed by the Engineer-in-charge..

Sqm. 8058

47 Providing and applying External Emulsion paint ofapproved colour of Compo Silicon W55 of SKKAKEN orequivalent make. Rate shall include surface preparation,with two coats of primer followed by 2 coats of siliconbased approved emulsion paint for excellent protectionand weatherability as per manufacturer specification withnecessary staging,scaffolding etc..as complete in allrespects complying with relevant standard specificationsand as directed by the Engineer-in-charge..

Sqm. 4096

Total of Internal & External Finishes Works

WATERPROOFING WORKS

48 Treatment to side wall, base slab of Lift pit from exteriorsurface covering the following sequence of operations :



Providing and applying 3 coats of crystallinewaterproofing slurry containing highly active, deeppenetrative, reactive catalysts and shall have a mixdensity of 2.0 kg/litre.. The product shall be applied in 3coats one over the other at a time gap of 4 to 6 hoursdepending on the climatic conditions, including curing ofthe same for at least 5 days fog spraying water. Rate isinclusive of material and labour. ProvidingCovings/Chamfers at junction of slab and wall with75mm X 75 mm fillet with cement sand mortar 1:2 mixedwith polymer modifier of styrene-butadiene co-polymerlatex liquid, produced from styrene and butadiene byhigh pressure emulsion polymerisation @ 5 L per bagcement. The product shall have minimum butadienecontent of 40% by weight. Protective Plaster: The coatedsurface should be protected with 1:3CM admixed withlignosulphonate polymer based, waterproofing cumplasticing liquid integral waterproofer at a dosage of 100ml per 50 kg of cement and shall comply with IS: 2645-2003. Treat the construction joints wherever necessary as

per below item specification.

Rate shall include for preparation of surface bymechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,scaffolding, waterproofing chemicals, wastage,conveyance, tools and plants, mixing device and gauge,Shuttering etc.as complete with all respects complyingwith relevant manufacturer's specification as directed bythe En ineer-in-char e.

Sqm. 233

49 Treatment to side wall,base slab of UG sump fromexterior surface covering the following sequence of

operations :Providing and applying 3 coats of of crystallinewaterproofing slurry containing highly active, deeppenetrative, reactive catalysts and shall have a mixdensity of 2.0 kg/litre. The product shall be applied in 3coats one over the other at a time gap of 4 to 6 hoursdepending on the climatic conditions, including curing ofthe same for at least 5 days fog spraying water. ProvidingCovings/Chamfers at junction of slab and wall with75mm X 75 mm fillet with cement sand mortar 1:2 mixedwith polymer modifier of styrene-butadiene co-polymerlatex liquid, produced from styrene and butadiene byhigh pressure emulsion polymerisation @ 5 L per bagcement. The product shall have minimum butadienecontent of 40% by weight. Protective Plaster: The coatedsurface should be protected with 1:3CM admixed withlignosulphonate polymer based, waterproofing cumplasticing liquid integral waterproofer at a dosage of 100ml per 50 kg of cement and shall comply with IS: 2645-2003. Treat the construction joints wherever necessary asper below item specification.



Rate shall include for preparation of surface bymechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,scaffolding, waterproofing chemicals, wastage,conveyance, tools and plants, mixing device and gauge,Shuttering etc.as complete with all respects complyingwith relevant manufacturer's specification as directed bythe Engineer-in-charge.

Sqm. 1919

50 Treatment for STP tanks covering the following sequenceof operation :

The STP tanks has to be protected with High build, pitchextended epoxy coating which shall be formulated toresist exposure to accelerated weathering test as perASTM D4587 and shall not exhibit any flaking orblistering. It shall be a 100% solids, solvent free, toughabrasion resistant protective coating used over pile caps.The product shall exhibit excellent bond strength with thesubstrate at least exceeding 2.5 MPa, when tested as perASTM D4541. The product shall be formulated to have

high build thickness exceeding 150 microns per coat onaverage and shall be applied to achieve overall thicknessof 300 microns in two coats.

Rate shall include for preparation of surface bymechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,scaffolding, waterproofing chemicals, wastage,conveyance, tools and plants, mixing device and gauge,Shuttering etc.as complete with all respects complyingwith relevant manufacturer's specification as directed bythe En ineer-in-char e.

Sqm. 1194

51 Treatment to side wall,base slab of OH Tank fromexterior surface covering the following sequence ofoperations :Providing and applying 3 coats of a two componentreactive polymer composite. The product shall be appliedin minimum three coats to achieve total DFT of 2 mm. Theproduct shall resist 7 bars pressure when tested as perDIN 1048 at 2mm DFT. The cured coating shall have thefollowing diffusion co-effiecient. Carbon dioxide – 4.21x107 cm2/s Oxygen – 7.60x10-6 cm2/s Chloride ion – 1.04x107 cm2/s. Rate is inclusive if material and labour.Providing Covings/Chamfers at junction of slab and wallwith 75mm X 75 mm fillet with cement sand mortar 1:2mixed with polymer modifier of styrene-butadiene co-polymer latex liquid, produced from styrene andbutadiene by high pressure emulsion polymerisation @ 5L per bag cement. The product shall have minimumbutadiene content of 40% by weight.



Protective Plaster: The coated surface should be protectedwith 1:3CM admixed with lignosulphonate polymerbased, waterproofing cum plasticing liquid integralwaterproofer at a dosage of 100 ml per 50 kg of cementand shall comply with IS: 2645-2003. Treat theconstruction joints wherever necessary as per below itemspecification.Rate shall include for preparation of surfaceby mechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,scaffolding, waterproofing chemicals, wastage,conveyance, tools and plants, mixing device and gauge,Shuttering etc.as complete with all respects complyingwith relevant manufacturer's specification as directed bythe Engineer-in-charge.

Sqm. 607

52 Treatment to sunken slab and its walls covering thefollowing sequence of operations

Providing and applying 3 coats of a two componentreactive polymer composite. The product shall be applied

in minimum three coats to achieve total DFT of 2 mm. Theproduct shall resist 7 bars pressure when tested as perDIN 1048 at 2mm DFT. The cured coating shall have thefollowing diffusion co-effiecient.Carbon dioxide – 4.21x107 cm2/sOxygen – 7.60x10-6 cm2/sChloride ion – 1.04x10-7 cm2/s.Rate is inclusive if material and labour. ProvidingCovings/Chamfers at junction of slab and wall with75mm X 75 mm fillet with cement sand mortar 1:2 mixedwith polymer modifier of styrene-butadiene co-polymerlatex liquid, produced from styrene and butadiene byhigh pressure emulsion polymerisation @ 5 L per bagcement.

The product shall have minimum butadiene content of40% by weight. Protective Plaster: The coated surfaceshould be protected with 1:3CM admixed withlignosulphonate polymer based, waterproofing cumplasticing liquid integral waterproofer at a dosage of 100ml per 50 kg of cement and shall comply with IS: 2645-2003. Treat the construction joints wherever necessary asper below item specification.( Note: Wall upto 1 M ht )

Rate shall include for preparation of surface bymechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,scaffolding, waterproofing chemicals, wastage,conveyance, tools and plants, mixing device and gauge,Shuttering etc.as complete with all respects complyingwith relevant manufacturer's specification as directed bythe Engineer-in-charge.

Sqm. 2396

53 Water proofing treatment over RCC roof slab laid to

slope in terrace and gutter slab with Thermal Insulation

covering the following sequence of operation andspecifications:



a) SURFACE PREPARATION: The roof slab laid in slope/ gutter slab shall be thoroughly cleaned by removing thedebris and dust, to receive the water proofing treatment.The cleaning and preparation of the substrate to whichthe asphalt-modified polyurethane based membranesystem is applied must be carried out thoroughly to leavea sound base for the application. Any laitance present onthe surface must be removed mechanically. Release oiland other contaminants which may impair adhesion mustbe removed prior to the application of the primer.

b) Waterproofing Membrane: Providing and applyingliquid, cold-applied elastomeric waterproofing membranesystem a single component moisture curing, asphalt-modified polyurethane based coating that cures byreaction with atmospheric moisture to form a tough butflexible waterproofing membrane. It is elastomeric,seamless waterproof membrane applied in 1 or 2 coats toa total DFT of 1.20 mm thick, having an elongation

capacity of over 600%(ASTM D 412) and with solidcontent more than 85% applied on the RCC surfaceincluding priming (if required), crack filling, grouting, tierod filling, coving, ponding etc complete. It shall resistbacterial attack and many acids, alkalis and salts. It shallhave a yield of 0.61-0.74 m2/L at 1.1 – 1.4mm drythickness SEPARATION LAYER: Providing and laying aseparation layer of non-woven polypropylene geo-textileof 200 gsm over the entire surface of insulation board.

-

c) INSULATION BOARD: Supplying and installation ofExpanded polystyrene board for thermal insulation on the

terrace of approved make. The insulation board shall beshape moulded and the insulation board shall avoidthermal bridging and have Tongue & groove arrangementfor fixing. The board shall have a K-value of 0.032 W/mKand Water Absorption of (% vol) : <0.05% (by totalimmersion) as per BS EN 12087.The board shall be freefrom CFC, HCFC and HFC. The board shall be selfextinguishing and shall have HF1 rating as per UL94 Teststandard. The Actual area covered would be used formeasurement. Refer technical data sheet for details.

-

d) SEPARATION LAYER:Providing and laying aseparation layer of non-woven polypropylene geo-textile

of 200 gsm over the entire surface of insulation board.



e) SLOPE/PROTECTION SCREED:Providing and layinglight-weight site batched trowel finished EPS concreteusing selective grade of EPS beads with a density of 12-18kg/m3, on the geotextile separation layer as in Item-3.The mix shall offer Thermal conductivity of 0.23 – 0.26W/m-ok,Comp strength (28 days) of 30-60 kg/cm2.Drydensity of 750-950 kg/m3. The mix shall have a watercement ratio of 0.28-0.32 and the hyper-plasticiser rangeof admixture shall have 1 – 2 % dosage by weight ofcement. The slope built-up cum protection layer shall belaid with a slope gradient of 1:100 (Rate considered for100mm thickness). It shall be laid to the required level andfinish as directed including curing by ponding for aminimum of 7 days. The mix proportion shall be pre-approved by Engineer-in-charge. Refer data sheet ofTHERMOCRETE for mix proportion.

f) FINISHING/WEARING LAYER: Providing andlaying China mosaic finish as the final exposed layer

of the floor complete as directed. The bedding mortarshall be cementitious polymer modified tile adhesivecapable to maintain adhesion under submergedconditions. The product shall have BS 5980 Type 1standards compliance. It shall have a fresh wet density of2.1 kg / litre and have 0.18 water/powder ratio, byweight. Immediately after setting of the tiles, rake joints &clean to a uniform depth corresponding to the thickness ofthe tile. All the ceramic tile joints shall be grouted using,crack resistant, cementitious, water resistant joint grout.The joint grout shall be formulated to maintain waterpowder ratio of 0.33 by weight and shall comply with BS5980.

Rate shall include for preparation of surface bymechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,scaffolding, supply and adding water proofing chemicalsat the specified proportion as per manufacturer'sspecifications, all materials, wastages, conveyance, toolsand plants, mixing device and gauge, shuttering and alsoinclude for conducting leakage test at terrace by storingwater on the terrace for about 25 mm depth continuouslyfor a period of 7 days etc.as complete with all respectcomplying with relevant manufacturer specification asdirected by the Engineer-in-charge.

Sqm. 2605

54 Water proofing treatment over RCC roof slab laid to

slope in terrace and gutter slab without Insulation

covering the following sequence of operation andspecifications:



a) SURFACE PREPARATION: The roof slab laid in slope/ gutter slab shall be thoroughly cleaned by removing thedebris and dust, to receive the water proofingtreatment.The cleaning and preparation of the substrate towhich the asphalt-modified polyurethane waterproofingmembrane is applied must be carried out thoroughly toleave a sound base for the application. Any laitancepresent on the surface must be removed mechanically.Release oil and other contaminants which may impairadhesion must be removed prior to the application of theprimer.

b) Waterproofing Membrane: Providing and applyingliquid, cold-applied elastomeric waterproofing membranesystem a single component moisture curing, asphalt-modified polyurethane based coating that cures byreaction with atmospheric moisture to form a tough butflexible waterproofing membrane. It is elastomeric,seamless waterproof membrane applied in 1 or 2 coats toa total DFT of 1.20 mm thick, having an elongation

capacity of over 600%(ASTM D 412) and with solidcontent more than 85% applied on the RCC surfaceincluding priming (if required), crack filling, grouting, tierod filling, coving, ponding etc complete. It shall resistbacterial attack and many acids, alkalis and salts. It shallhave a yield of 0.61-0.74 m2/L at 1.1 – 1.4mm drythickness SEPARATION LAYER: Providing and laying aseparation layer of non-woven polypropylene geo-textileof 200 gsm over the entire surface of insulation board.

c) SEPARATION LAYER: Providing and laying aseparation layer of non-woven polypropylene geo-textile

of 200 gsm over the entire surface of insulation board.

d) Providing and laying light-weight site batched trowelfinished EPS concrete using selective grade of EPS beadswith a density of 12-18 kg/m3, on the geotextileseparation layer as in Item-3. The mix shall offer Thermalconductivity of 0.23 – 0.26 W/m-ok,Comp strength (28days) of 30-60 kg/cm2.Dry density of 750-950 kg/m3. Themix shall have a water cement ratio of 0.28-0.32 and thehyper-plasticiser range of admixture shall have 1 – 2 %dosage by weight of cement. The slope built-up cumprotection layer shall be laid with a slope gradient of 1:100

(Rate considered for 100mm thickness). It shall be laid tothe required level and finish as directed including curingby ponding for a minimum of 7 days. The mix proportionshall be pre-approved by Engineer-in-charge. Refer datasheet of THERMOCRETE for mix proportion.



e) FINISHING/WEARING LAYER: Providing and layingChina mosaic finish as the final exposed layer of thefloor complete as directed. The bedding mortar shall becementitious polymer modified tile adhesive capableto maintain adhesion under submerged conditions.The product shall have BS 5980 Type 1 standardscompliance. It shall have a fresh wet density of 2.1 kg /litre and have 0.18 water/powder ratio, by weight.Immediately after setting of the tiles, rake joints & clean toa uniform depth corresponding to the thickness of the tile.All the ceramic tile joints shall be grouted using, crackresistant, cementitious, water resistant joint grout. The joint grout shall be formulated to maintain water powderratio of 0.33 by weight and shall comply with BS 5980.

Rate shall include for preparation of surface bymechanical upgrading to remove all loose mortar andlaitance, oil, grease etc. and washing the surface withwater to get neat surface, dewatering, finishing, curing,

scaffolding, supply and adding water proofing chemicalsat the specified proportion as per manufacturer'sspecifications, all materials, wastages, conveyance, toolsand plants, mixing device and gauge, shuttering and alsoinclude for conducting leakage test at terrace by storingwater on the terrace for about 25 mm depth continuouslyfor a period of 7 days etc.as complete with all respectcomplying with relevant manufacturer specification asdirected by the Engineer-in-charge.

Sqm. 2398

55 Providing and laying brickbat coba in CM 1:4( one ofcement & four of brickjelly) using well burnt half bricks /bats of 20mm size brickjelly for using toilets and other

specified areas including ramming, curing etc.. allcomplete as directed by Engineer-v

Cum 746



56 Providing chemical injection in the form of pressure

grouting to the base slab of Lift pit,retaining walls of liftpit,underground sump and STP from interior surfacesworks at any depth, height and level by Drilling 12mmdia holes with percussive drilling machine at areas withhoneycombs and at weak zones in the concrete in astaggered pattern at to a depth of 50mm and fixing PVCnozzle of 10mm dia in place using quick settingcompound Masterseal 505 of approved maket.Pressuregrouting cement slurry mixed with shrinkagecompensating additive Flowcable 50, at 250 gms per bagof cement, using hand operated pressure grouting pumpwith a pressure of 2 to 3 kg/sq.cm through the nozzles bystarting from one nozzle and stopping when the groutstarts coming out from adjacent nozzle or getting rejectedfrom the same nozzle and similarly carrying out groutingoperation in all the nozzles as per approved manufacturerspecifications in all the points including the cost ofchemical, labour for carrying grouting operations etc.. ascomplete.

Rate shall include for preparation of surface, de-watering,drilling holes, using pneumatic hammer for fixing of PVCnozzles to the required depth, grouting admixture andfinally cutting the projected nozzles and sealing of thePVC nozzles after injection operation is over withapproved equivalent admixed with cement, finishing,curing, etc., as per manufacturer‟s specification. Rate shallinclude for preparation of surface by mechanicalupgrading to remove all loose mortar and laitance, oil,grease etc. and washing the surface with water to get neatsurface, dewatering, finishing, curing, scaffolding,waterproofing chemicals, wastage, conveyance, tools and

plants, mixing device and gauge, shuttering, Nozzles etc.complete as per manufacturer's specification and asdirected by the Engineer-in-charge.

Sqm. 3113

Total of Waterproofing Works

MISCELLANEOUS WORKS

57 Providing, supplying and spraying/spreading the Fire

sealing in shaft chequered plate for pipeoutlets,trays,cables,openings of required dia.outlets usingpenetration seals of approved make inclusing necessarymechanical equipments,tools and tackles etc

complete.cost to include cotton pads,sealing of jointsusing self sealing, non shrink cement penetration seals /grouts of approved makes either single or doublecomponent with necessary formwork, staging, tools, etc.,complete with minimum of 30 mm depth for two hoursfire rating.Hilti or Promat or Equivalent make areapproved by the Engineer-in-charge.

Sqm. 498



58 Making Core Cutting in slabs / beams / retaining wallsand any other R.C members to any dia & depth by using'HILTI' or equivalent make diamond drilling machinewith tolerance for any type of inserts, anchor fasteners etc.Rate shall include for all charge, preparation of surface,cutting of reinforcement, cleaning the surface, staging,scaffolding application of necessary chemical / foil (HAV)as per manufactures specification with necessary toolsand equipments water and power, removal of debris fromthe site, staging scaffolding etc complete, as directed bythe Engineer-in-charge.

a 75 to 100 mm dia to the following depth:

i 150 mm Depth Nos 10

ii 200 mm Depth Nos 10

iii 250 mm Depth Nos 10

iv 300 mm Depth Nos 10

b 100 to 150 mm dia to the following depth:





c 150 to 225 mm dia to the following depth:





d 225 to 300 mm dia to the following depth:




iv 300 mm Depth Nos 10e 300 to 450 mm dia to the following depth:





59 Supplying and fixing poly-propelene rungs of 25 mmsquare bar of size 260 x 170 mm for access way includinganchorage in walls to a minimum depth of 100 mm withC.C 1:2:4 (one cement,two fine aggregate and four coarseaggregate) etc. complete and as directed by the Engineer-in-charge.( Duct ,Shafts & UG sump,Over Head Tank and

wherever necessary) Note: Rungs to be fixed beforeconcreting and necessary provision to be made in theshuttering.etc complete, as directed by the Engineer-in-charge.

No's 100



60 TRANSPLANTING Transplanting of Tree fouling in theproposedbuilding layout in ONGC project to the suitable place asper the Architectual drawing and as directed by theEngineer in charge,includingtrimming the tree branches excavating earth around thetree to required length,width and depth to remove thetree with required roots to transport the tree to newlocation as per the drawing inside thesite and digging the new pit,torequired size to transplantthe tree including cost for earth workexcavation,trimming the tree branches to requiredsize,removing and shifting the tree using machinaries andequipments to new location as per the drawing and asdirectedby the Engineed in charge, digging required size of pit totransplant the tree, refilling the pit after planting the treewith river sand,poring water and providing manure etc.,and maintaining the tree planter for a further period ofTwenty Four months including watering etc.,complete as

directed,includes for all operations as discribed andnothing extra shall be paid for

Rain Tree,Coconut Tree. Etc., Nos 30

61 CUTTING, AND REMOVING Cutting the dead treesand trees which are not able to transplant etc., in to piecesincluding uprooting the trees,by excavating earth torequired size and levelling the ground after removal ofthe trees and cutting pieces of trees stacked in site asdirected by the engineer in charge. Note: Prior permissionfrom the forest department shall be obtained beforecutting.

Rain Tree,Neem tree etc., Nos 32

62 Clearing light / scrub jungle and removal of rubbish upto a distance of 50 m outside the periphery of the areacleared etc all complete as directed by the engineer incharge.

Sqm. 30000

63 18 Credit to Client towards the dismantling and takingaway from the site of existing old dilapidated Asbestos

Cement (AC) sheet roof buildings having the followingdimensions. The rate shall inclusive of dismantling thesuperstructure with any type to any thickness, masonry,walls, lintels, beams, plastering, flooring, wooden/steeltrusses, rafters, pulins, AC roof sheeting, anyReinforcement Concrete members, ,joineries like doors,

windows, ventilators, internal & external electrical wiringwith fixtures, water supply and sanitary installations andthe like as exists at site including substructures to therequired full depth as directed. The rate shall includedisposing of unserviceable materials away from the site,including clearing the site neatly etc. all complete asdirected by the engineer in charge. Note: Prior approvalshall be obtained from the concerned department.

AC sheet roof building of size 7.20 x 4.50m No. 1



AC sheet roof building of size 6.40 x 6.40m No. 1AC sheet roof building of size 7.60 x 7.60m No. 1AC sheet roof building of size 21.50 x 9.70m No. 1

64 18 Credit to Client towards the dismantling and takingaway from the site of existing reinforced cement concrete

(RCC) roof buildings having the following dimensions.The rate shall inclusive of dismantling the superstructure

with any type to any thickness, masonry, walls, lintels,beams, columns, plastering, flooring, roof slab, ,joinerieslike doors, windows, ventilators, internal & externalelectrical wiring with fixtures, water supply and sanitaryinstallations and the like as exists at site includingsubstructures to the required full depth as directed. Therate shall include disposing of unserviceable materialsaway from the site, including clearing the site neatly etc.all complete as directed by the engineer in charge. Note:

Prior approval shall be obtained from the concerneddepartment

Community center building 17.50 x 9.50m Nos. 1

65 18 Dismantling of Brick Work / Stone work / Solid Block

Work including plastering/pointing to any depth andwidth, at all levels below & above Ground Levelincluding removal of debris, disposing the same awayfrom the site, loading and unloading, making the surfacegood etc. complete. Rate shall include for dismantling ofBrick Work / Solid Block Work includingplastring/pointing, removal of debris by manual /mechanical means with necessary tools and plants,scaffolding, water and power charges, cleaning thesurface, preparation of surface. Rate shall include forstacking the serviceable materials and disposing the

unserviceable materials/debris away from the site bymechanical means including loading, unloading clearingthe site etc. complete as directed by the Engineer-in-charge.

Cum 141

66 Providing and laying of light weight concrete fill on

structural slab using Hemalite/Vermiculite cement basedcomposition having physical elasticity , chemicalinertness, firm adhesion, fire resistance with thermal /acoustic insulation properties, anti-corrosion, anti-condensation, etc in the required proportion to get thedesired density, mixing, transportation, placing,compacting and finishing to the required level withnecessary side supports, equipments and its density is600kg/cum wherever necessary areas to be fill as directedby the Engineer-in-charge.etc as complete with allrespects complying with relevant standarad specificationas directed by the Engineer-in-charge.

Cum 39



67 Supplying and fixing 40mm dia. and 150mm or more longG.I. pipe spouts in sun shades including painting twocoats of first quality synthetic enamel paint of approvedmake and tint over one coat of primer as complete in allrespects complying with relevant standard specificationand as directed by the Engineer-in-charge.

No's 50

68 Supplying and fixing Ductile Iron manhole cover andframe as per approved make ,cover weight and being sizementioned below and specified size in the drawing etc.,including painting with two coats of anticorrosive paintover a coat of primer etc., fixing locking arrangements,fixing Man-hole over, grouting the anchors with CC 1:2:4(one cement,two fine aggregate and four coarseaggregate), as complete in all respects complying withrelevant standard specifications and as directed by theEngineer-in-charge.

a 600X600 mm Medium duty DI manhole cover not lessthan 65kgs

No's 10

b 600X600 mm Heavy duty DI manhole cover not less than90kgs

No's 49

69 Providing Plinth protection with PCC 1:3:6 (One cement,three fine aggregate and six coarse aggregate) 50mm thickusing coarse graded aggregate of 20 mm and downsize,top finished smooth while wet and laid with a nominalslope, over a sand bed of 75 mm thick including necessaryexcavation wherever, necessary form work etc . The endslab shall have 115 mm thick brick retaining walls withCM 1:4 (one cement and four fine aggregate) at the edge300 mm high. The exposed faces of wall shall be plasteredwith cement mortar 1:5 - 15 mm thick. The effectiveseparation of panels not exceeding 10 sqm in plan by

making grooves or by using glass or other metals stripsetc.and also including for providing necessary form work,excavation, refilling, consolidation and compaction offilled earth, plastering, pointing, curing and reinforcementas complete in all respects complying with relevantstandard specification and as directed by the Engineer-in-charge.

Sqm. 872

70 Providing and laying in position the RCC

humepipes(NP2) of approved quality and makeincluding collars,. necessary Excavation, PCC 1:2:4supports, Sand cushion of 150mm on all sides, Refilling

with earth, Compaction and making good the level,alignment etc.,complete as directed by the Engineer-in-charge.

a 300 mm dia RMT 410



71 Supplying and fixing single skin bare Galvalume metalsheet Roof cladding for car shed at all heights using 0.47mm TCT 550 Mpaprofiled Galvalume steel (Aluminium zinc alloy coating150 gms / sqm total of both sides) sheet includingnecessary structural steel frame work consisting of allvertical / horizontal members,purlins, and all otherfixtures etc. The rate should inclusive of cutting,fabricating, erection at all levels, providing openings, allfixtures and fixing accessories such as self drilling, selftapping fasteners, butyl or acrylic sealants, profiled foam/neoprene fillers etc. including necessary civil works toerect the vertcal struts, two coats of PU painting over onecoat of zinc chromate primer, cost of all materials, steelmembers, purlins, labour,scaffolding, wastage, tools,tackles, equipment,transportation, preparation of shopdrawings etc. all complete as per specifications, drawingsand asdirected by the Engineer-incharge.

Sqm. 1323

72 Supplying, fabricating, erecting, testing andcommissioning of Cylinder Manifold system,centralizedGas Bank with individual connection toall kitchens using reticulated LPG pipeline with (Schedule40) 25 mm dia C class MS pipe and appropriate 16mm /20mm razor composite pipe tothe required length as per the site condition up to theconnection point inside the kitchen in the C&D typeresidential block. The rate should include the cost of gasmeter, inlet, outlet fittings, all other necessary accessorieslike butterfly valves, pressure gauges, gas filters, non-return valves, flexible hoses, composite brass fittingsetc..as requied to complete the work in all respects and

testing and commissioning all as per IS6044 Part-1 2000specification and as per the approved firm. The rate shallinclude all necessary materials and accessories, civilworks, painting,scaffolding, core cutting wherevernecessary, and making goodcondition, power etc.. as directed.

Job (One Job). 66

Total of Miscellaneous Works

ROAD & PAVEMENT WORKS

Concrete Road

73 Preparation & sectioning the area road surface and

compacting with 10 ton power roller including formingcamber and gradients watering and rolling to reachrequired density as complete.as directed by the Engineer-in-charge.

Sqm. 11808



74 Construction of 300mm thk Granular subbase (GSB) byproviding coarse graded material 53mm to 4.75 mm,spreading in uniform layers with motor grader onprepared surface mixing by mix in place method withrotavator at OMC and compacting with vibratory roller toachieve the desired density, as complete in all respectscomplying with relevant standard IRC,MORTH andMOST Specifications and as directed by the Engineer-in-charge.

Cum 3543

75 Providing, Laying, Spreading and compacting 45 mm to4.75 mm graded stone aggragate of 200mm thk wet mix

macadam (WMM) specification including premixing thematerial with water at OMC in mechanical mixplant,carriage of mixed material by tipper to site,laying inuniform layers with paver in subbase / sub course onwell prepared surface and compacting with vibratoryriller to achieve the desired density,as complete in allrespects complying with relevanat standard MOSTspecification,as directed by the Engineer-in-charge.

Cum 2362

76 Providing and laying 100mm thk. Plain cementconcrete1:3:6 (One cement, three fine aggregate and sixcoarse aggregate) by using coarse graded aggregate of 25mm and down size for levelling course in road andpavement areas wherever necessary (as per drawing)including laying in layers of thickness not exceeding100mm and in alternative bays not exceeding 40 sqm asdirected including form work wherever necessary andwell compacted etc. as complete in all respects complyingwith relevant standard specification as directed by theEngineer-in-charge

Cum 1181

77 Providing and laying controlled cement concrete mix ofM20 grade to a thickness of 150 mm for roads andpavements laid to required slope and camber in panelsconfirming to IRC standard. Rate shall include forproviding IRC Weldmesh of size 100x100 - 12 Gauge - onelayersconfirming to IS: 1566 & IS: 4948 or equivalentBS,necessary formwork, shuttering,props, bracing andwedges, sufficiently strong & stable, providing 25 mmwide expansion joints and construction joints& closing the joints using polyurethene sealant -"VULKEM" - 202 PU from Supreme or approvedequivalent make etc.complete, as directed by the

En ineer-in-char e .

Cum 1771

78 Kerb and Pavement works



Providing and fixing vacuum wetpress concrete precastSplay kerb to shape by using reinforced cement concreteM20 grade road kerbs of size 150X375X600 mm made toshape using 20 mm down size Coarse graded Basaltaggregate including form work and nominalreinforcement of Fe 415 grade, 12 mm dia at 150 c/c with8 mm dia stirrups at 150 mm c/c fixing in cement concrete1:3:6 nominal mix (one cement,three sand and six hardstone jelly) including all materials and labourcomponents,laying,finishing,curing and the pointingexposed faces with C.M 1:3 (one cement and three finesand) and colour washing with acrylic emulsion over acoat of primer etc..as complete in all respects complyingwith relevant standard specifications and as directed bythe Engineer-incharge.

RMT 3280

79 Supplying and laying Shotblasted Flexi Pavers of

approved design - 65 mm thick, total weight shall be 25kg approximately per one set or 1.94 Sft of flexi paverscontains five pieces including transportation of the blocks

to the site ,preparation of surface,supplying and fillingwith dry river sand to 50 mm thick, leveling andcompacting with plate vibrator and laying of the flexipaver blocks with sand binding and final compactionwith plate vibrator of 3 tone capacity finishing the surfaceincluding cutting of blocks at the edges including alllabour and materials etc as complete in all respectscomplying with relevant standard specification, asdirected by the Engineer-incharge. (For Pathway)

Sqm. 2792

80 3000 Providing thermoplastic painting for car park and road

line and arrow marks with 100mm wide involvingcleaning the surface free of dirt and loose particles

applying one coat of primer and applying one layer ofthermoplastic paint wih drop on glass beads. Rate shallinclude for all materials & labour components etc., ascomplete all respects complying with relevant IRCspecifications, as directed by the Engineer-incharge.

RMT 1808

Total of Road & Pavement Works

Tennis Court

81 Preparation, Formation & Construction of Tennis court asper the ITF (International Tennis Federation) specificationhaving the following sequence of works:

i Earth work excavation to the required depth as shown in

the drawing by manual/mechanical including levellingthe base, dressing of sides and ramming with all leadsand lifts, shoring, strutting and bailing out of water ifrequired.The rate shall include disposing the excavatedearth away from the site or dumping & levelling insidethe campus as directed.



ii Filling and levelling of good earth brought from outsideand to be laid in layers of 150mm thick and compactedwith 10tonne power vibrating roller including formingrequired gradient (1:10),watering and rolling to reach therequired density etc., as directed.

iii Providing Anti-termite treatment over the prepared basesurface using approved chemical in appropriateproportion to avoid the growth of weeds and termites, asdirected.

iv Construction of 200mm thk Granular subbase (GSB) byproviding coarse graded material, spreading in uniformlayers with motor grader on prepared surface mixing bymix in place method with rotavator at OMC andcompacting with vibratory roller to achieve the desireddensity, as directed.

v Providing, Laying, Spreading and compacting gradedstone aggragate of 150mm thk wet mix macadam (WMM)

specification including premixing the material with waterat OMC in mechanical mix plant,carriage of mixed

material by tipper to site, laying in uniform layers overthe granular sub-base and compacting with vibratoryroller to achieve the desired density,as directed.

vi Providing and laying Dense Bitumen Macadam forcompacted thickness of 30mm using 20mm down sizemetals mixed with 80/100 grade hot bitument at 4% ofweight and mix from central hot mix plant and laid bypaver finishing and compacting with vibratory roller.Rate shall be include with all plants and machineries, cost,conveyance and incidential charges, as directed.

vii Providing and laying of 30 mm compacted thick asphalt

concrete (HOT MIX) over the dense bituminousmacadam base with IRC standard 12mm and downcoarse graded basalt aggregate and binder content byusing 80/100 grade Bitumen, adopting suitable job mixformula as directed, including surface preparation,heating and mixing in central hot mix plant to therequired temperature, cost and conveyance of allmaterials to site, laying the mix to the requiredtemperature, specified lines, grades, gradient and crosssection using mechanical paver finisher and consolidationby 10 tonne power roller to get the required densityincluding all labour charges, hire and fuel charges for all

tools and plants employed etc., as directed.



viii Providing and laying of 20 mm compacted thick asphalt

concrete (HOT MIX) over the dense bituminousmacadam base with IRC standard 6mm and down coarsegraded basalt aggregate and binder content by using80/100 grade Bitumen, adopting suitable job mix formulaas directed, including surface preparation, heating andmixing in central hot mix plant to the requiredtemperature, cost and conveyance of all materials to site,laying the mix to the required temperature, specifiedlines, grades, gradient and cross section using mechanicalpaver finisher and consolidation by 10 tonne power rollerto get the required density including all labour charges,hire and fuel charges for all tools and plants employedetc., as directed.

ix Providing and laying tack coats over the prepared surfaceof WMM,DBM,30mm thk asphalt as per the MORTHspecification, as directed.

x Providing and laying seal coat (Type-B) over theprepared surface of 20mm thk asphalt as per the MORTH

specification, as directed.xi Providing and laying ITF certified Ultra cushion nine

layer system Synthetic surface over the 20mm thickAsphalt Base, it shall be made ready by cleaning withWater and is checked for any Bird Baths. Minor Patchwork if required shall be carried out done with acrylicresurfacer. The ratio of mixing of resurfacer for Patchwork is 3 (acrylic resurfacer): 1 ½ (Silica Sand) : 1 (Water)The rate shall include for supply and installation of a)Resurfacer to make an underlay for the cushion surfacecomprising of Mixing ratio is 3:1.25 (Silica Sand) : 1(water). b) Five Cushion layers above the resurfacercomprising of Mixing ratio of 4 (cushion) : 1 Water. c)First & Second Layer of Colour shall be provided andinstalled on top of the Cushion layer. Mixing Ratio is 5(acrylic Colour) : 3 (sand) : 2 ½ (Water)d) Third layer ofColour is poured on top of the first layers of Colour.Mixing Ratio is 2:1 (Water). e) Supply and installing LineMarking.All Acrylic is poured onto the surface and spreadwith a Squeejie.

xii In addition to the above sequence of works, the quotedrates shall inclusive of power, water, CIF values ofsynthetic surface, transportation, installation, all dutiesand taxes, etc.,as complete in all respects complying withrelevant standard specification .as directed by the

Engineer-Incharge.

Sqm. 674

82 Providing and constructing of Edge wall/Retaining RCCwall in cement concrete M25 grade, around the perimeterof the tennis court including necessary form work,reinforcement, base PCC, etc., all as shown in thedrawing, as directed by the Engineer-incharge.

RMT 110

83 Providing and constructing of Saucer Drain with gratingsalong the longer end of the tennis court, all as shown inthe drawings.

RMT 37



84 Supplying, fabricating and fixing in position of PVCcoated 10 gauge chain link Wire mesh fencing fixed alongwith GI Pole pipes measuring 3.0m high from toe walland one metre insert the toe wall around the perimeter ofthe tennis court (as per drawing) at all levels with theprovision of door opening of the required size & profileconsisting of channels, angles, runners, insert plates, flatsand sag rods with necessary sleeves, bolts andnuts,pipes,embedding the poles in concrete etc.. includingcutting, straightening, welding as per standards forconnections including consumables etc.as complete. Rateshall include preparation of surface, applying two coats ofZinc chromate/Phosphate primer and two coats ofsynthetic enamel paint of approved make etc.. as directedby the Engineer-incharge.

Sqm. 279

85 Supplying,fabricating and Fixing ITF certified Tennis Net

of size 42X 3 feet fixed to the MS net post of size80x80X3mm as shown in the drawing and as perapproved make and specification including ITF certified

Water Removing Roller as per approved make andspecification.etc., as directed by the Engineer-incharge.

No. 1

Total of Tennis Court

86 Golf Fencing

Supply and installation of High strength weather proofpolyolefin Golf Fencing Net of approved brand using1.5mm twisted and 2mm mesh square to height of 20malong with the 100mm dia MS hollow pipe erected atequal intervals including plates,nutbolts,cleats, ladder,8mm dia PVC coated Steel wire rope for net erectionetc..as per the specification. The rate shall be including of

all necessary civil works, Structural works, epoxy paintingworks, power, electricity,erection machneries etc.. asdirected by the Engineer-incharge.

Golf Fencing RMT 140

Total of Golf Fencing

87 Garbage Chute

Supplying, Fabricating and commissioning of CentralizedGarbage chute of approved make (SS430 X 1.2mm thk),450mm dia ( Ground to Eighteenth Floor ) .with aprovision of autoclosing intake down at every floor leveland a fire rated door (90 minutes rating-UL label 10B) at

the discharged end, with required garbage trolley, etc.,complete as per BS 1703:2005,IS6924-2001& NBC 2005specification. The rate shall include all installationcomponents, scaffolding for erection, required structuralbrackets with anchor fasteners, Sprinklers for fire andcleaning, necessary vent with bird netting etc.. as directedby the Engineer-incharge.

No. 1

Total of Garbage Chute



A - SANITARY FIXTURES & FITTINGS: (PROVIDING &

INSTALLATION)

- Note:

Detail of Sanitary fixture are for the information of theContractor, however model / makes of all sanitary fixtureshall be selected by Engineer-Incharge and the same shallbe binding for execution

No additional all fixing cost shall be paid for change intype of sanitary fixture or fitting.Provision of extension piece for final connection of CPfitting shall be supplied and installed by the contractoraccordingly (as required)

88 102 Providing & Fixing, testing and commissioning of whitevitreous China wall mounting type European water

closet (RS346467460) including providing & fixing C.P.bolts, nuts (C8152), bakelite / poly propylene seat & cover(RA80P467001) with C.P. hinges & rubber buffers, C.P.brass screw, washer with all accessories. Including cutting& making good the walls, floors, slab wherever requiredand as complete, as directed by Engineer-Incharge (Make

:- ROCA / Equal approved make, Model:-GIRALDAWALL HUNG WC WITH SOFT CLOSE SEATCOVER)

Nos. 191


closet (RS346247000) including providing & fixing C.P.bolts, nuts (C8152), bakelite / poly propylene seat & cover(RA8012A2004) with C.P. hinges & rubber buffers, C.P.brass screw, washer with all accessories. Including cutting& making good the walls, floors, slab wherever requiredas directed by the Engineer-incharge. (Make :- ROCA/Equal approved make, Model NEW MERIDIAN WALLHUNG WC WITH SOFT CLOSE SEAT COVER- )

Nos. 8


closet (RS346477000) including providing & fixing C.P.bolts, nuts (C8152), bakelite / poly propylene seat & cover(RA8012A2004) with C.P. hinges & rubber buffers, C.P.brass screw, washer with all accessories. Including cutting& making good the walls, floors, slab wherever requiredand as complete, as directed by Engineer-Incharge (Make:- ROCA/ Equal approved make, Gap wallhung with soft

close seat cover )

Nos. 4




closet (C0255) including providing & fixing C.P. bolts,nuts (C8152), bakelite / poly propylene seat & cover(RA8012A2004) with C.P. hinges & rubber buffers, C.P.brass screw, washer with all accessories. Including cutting& making good the walls, floors, slab wherever requiredand as complete, as directed by Engineer-Incharge(Make :ROCA/ Equal approved make, Model:- Indus Walvit Panwith seat cover )

Nos. 2

92 102 Providing&Fixing, testing and commissioning of whitevitreous China Indian type(orissa patern) water closet.Including cutting & making good the walls, floors, slabwherever required and as complete, as directed byEngineer-Incharge (Make :- ROCA/ Equal approvedmake, Model & No.Orissa Pan 500mm - C0111)

Nos. 2

93 102 Providing, fixing, testing and commissioning of exposedplastic low level cistern for WC, with dual flush facility

complete with all necessary fittings, flush pipes &accessories including all supports and making good andas complete, as directed by Engineer-Incharge (Make :-ROCA/ Equal approved make, Model & No.SlimlineEconomy Dual flush - C8109)

Nos. 2

94 102 Providing&Fixing, testing & commissioning of concealed

type cistern with dual flush facility comprising ofactuator button facia assembly and Push plat includingbrass / SS screws and washer complete, providingprotection cover over cistern, cutting and making goodthe walls wherever required and as complete, as directedby Engineer-Incharge (Make :- ROCA/ Equal approvedmake, Model:- Slendra concealed cistern 80 mm , No:-RA890031410, Chrome Push plate round knob No:-RA8900450B1 )

Nos. 205

Health Faucet

95 102 Providing&Fixing, testing & commissioning of ABSRinsing spray with regulator of approved quality withplastic flexible pipe 1.5 m long, wall hook complete asrequired and as complete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:-Health faucet No:- ALD-563)

Nos. 197

96 102 Providing&Fixing, testing & commissioning of ABS

Rinsing spray with regulator of approved quality withplastic flexible pipe 1.5 m long, wall hook complete asrequired and as complete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:-Health faucet No:- ALD-577)

Nos. 8

Wash basin



97 Providing&Fixing first quality white vitreous china oval /round / square wash basin (RS327465000) (size as perarchitectural drawing) for counter top mounting, 32 mmCP brass waste coupling and CP brass cast bottle trap(Make :- Jaquar/ Equal approved make, Model:- ALD-709& ALD-769 ) and pipe to wall with CP brass flange andrubber adopter for waste connection complete includingfilling gap between counter and wash basin withapproved type poly sulphide sealant, cutting and makinggood the walls wherever required and as complete, asdirected by Engineer-Incharge (Make :- ROCA// Equalapproved make , Model:- Giralda countertop basin600*475 mm, )

Nos. 228

98 Providing&Fixing first quality white vitreous china oval /round / square wash basin (RS327240000) (size as perarchitectural drawing) for counter top mounting, 32 mmCP brass waste coupling and CP brass cast bottle trap(Make :- Jaquar/ Equal approved make, Model:- ALD-709& ALD-769 ) and pipe to wall with CP brass flange and

rubber adopter for waste connection complete includingfilling gap between counter and wash basin withapproved type poly sulphide sealant, cutting and makinggood the walls wherever required and as complete, asdirected by Engineer-Incharge (Make :- ROCA/ Equalapproved make, Model:- Meridian N wall hung washbasin 700*460, )

Nos. 2

99 Providing&Fixing first quality white vitreous china oval /round / square wash basin (RS327115000) (size as perarchitectural drawing) for under counter mounting, 32mm CP brass waste coupling and CP brass cast bottle trap(Make :-Jaquar/ Equal approved make, Model:- ALD-709

& ALD-769 ) and pipe to wall with CP brass flange andrubber adopter for waste connection complete includingfilling gap between counter and wash basin withapproved type poly sulphide sealant, cutting and makinggood the walls wherever required and as complete, asdirected by Engineer-Incharge (Make :- ROCA// Equalapproved make, Model:- Diverta UC washbasin620*440mm)

Nos. 22

100 Providing&Fixing first quality white vitreous china oval /round / square wash basin (C0471) (size as perarchitectural drawing) for counter top mounting, 32 mmCP brass waste coupling and CP brass cast bottle trap(Make :- Jaquar/ Equal approved make, Model:- ALD-709& ALD-769 ) and pipe to wall with CP brass flange andrubber adopter for waste connection complete includingfilling gap between counter and wash basin withapproved type poly sulphide sealant, cutting and makinggood the walls wherever required and as complete, asdirected by Engineer-Incharge (Make :- ROCA/ Equalapproved make, Model:- Indus basin (500*400mm),

Nos. 2



101 Providing&Fixing first quality white vitreous china oval /round / square wash basin (RS327874000) (size as perarchitectural drawing) for counter top mounting, 32 mmCP brass waste coupling and CP brass cast bottle trap(Make :- Jaquar/ Equal approved make, Model:- ALD-709& ALD-769 ) and pipe to wall with CP brass flange andrubber adopter for waste connection complete includingfilling gap between counter and wash basin withapproved type poly sulphide sealant, cutting and makinggood the walls wherever required and as complete, asdirected by Engineer-Incharge (Make :- ROCA/ Equalapproved make, Model:- kalahari vanity Basin650*450mm)

Nos. 16

102 Providing&Fixing first quality white vitreous china oval /round / square wash basin (RS32751A000) (size as perarchitectural drawing) for counter top mounting, 32 mmCP brass waste coupling and CP brass cast bottle trap(Make :- Jaquar/ Equal approved make, Model:- ALD-709& ALD-769 ) and pipe to wall with CP brass flange and

rubber adopter for waste connection complete includingfilling gap between counter and wash basin withapproved type poly sulphide sealant, cutting and makinggood the walls wherever required and as complete, asdirected by Engineer-Incharge (Make :- ROCA/ Equalapproved make, Model:-Dama Senso Compacto squarewashbasin 650*470mm )

Nos. 2

Basin mixer

103 Providing&Fixing, testing and commissioning of Basinmixer with Aerator and wall flange (as required) andmaking good as required and as complete, as directed byEngineer-Incharge (Make :- Jaquar/ Equal approved

make, Model:- OPL 15051B)

Nos. 268

104 Providing&Fixing, testing and commissioning of Basinmixer with Aerator and wall flange as required andmaking good as required and as complete, as directed byEngineer-Incharge (Make :- Jaquar/ Equal approvedmake, Model:- KUB 35051B).

Nos. 4

Urinal

105 Providing&Fixing, testing and commissioning of whiteviterous china urinal including providing & fixing CI /MS bracket (duly painted with 2 coats of paints over acoat of primer), including CP brass waste with dome typegrating, complete with all accessories and as complete, asdirected by Engineer-Incharge (Make :- ROCA/ Equalapproved make,Model:-Integrated EFS - Smart AC withPower Source, C8195)

Nos. 7



106 Providing, fixing, testing and commissioning of whiteviterous china large flat back / half stall urinal supportedby CI / MS bracket (duly painted with 2 coats of paintsover a coat of primer), including CP brass waste withdome type grating, CP cast brass bottle trap withextension piece, wall flanges complete with all accessoriesand as complete, as directed by Engineer-Incharge ((Make:- ROCA/ Equal approved make,Model:-Euret urinal425*797 mm back inlet, RS35945F000)

Nos. 8

107 Providing, fixing, testing and commissioning of automaticflushing systems for urinal to ensure pre-flush & flushingonly immediately after use, comprising of all plumbing,electronic and electrical items. CP brass flush pipe withCP brass elbow, CP brass spreader, CP wall flange,infrared photo cells, eyes electrically operated solenoidvalve, step down transformer / equipment and any otheritem required to provide satisfactory functioning.Including necessary wall cutting / chasing and makinggood, as required and as complete, as directed by

Engineer-Incharge (Make :- ROCA/ Equal approvedmake,Model:-Urinal sensor powered by 220 volts - AC,RT5X9415E00)

Nos. 15

108 Providing & Fixing, testing, and commissioning of Acrylicbath tub (Vythos drop-in bathtub 1700*800mm)completely leveled, including waste overflow drain set(RF506403010) , chain plug, legs, grouting of legs etc withcement concrete all complete as required and as complete,as directed by Engineer-Incharge (Make :- ROCA/ Equalapproved make, Model:- RW247701000)

Nos. 2

109 Providing & Fixing Deck mount bath tub mixer with

spout and telephonic hand shower and as complete, asdirected by Engineer-Incharge.((Make :- ROCA/ Equalapproved make, Model:- AMURA 4 HOLE HIGHNECKTUB FILLER +H.SWR, RT527306580)

Nos. 2

Shower area

110 Providing&Fixing Concealed bath shower divertor, Singlelever divertor exposed parts, spout, shower arm,overhead shower and wall flanges complete and ascomplete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:-ALD - 065, KUB -35065K, SPJ- 35429, SHA - 479 L 450, and OHS-1823 ).

Nos. 4

111 Providing&Fixing Concealed bath shower divertor, Single

lever divertor exposed parts, spout, shower arm,overhead shower and wall flanges complete and ascomplete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:-ALD - 065, OPL -15065K, SPJ- 429, SHA - 483 L 450, and OHS-1779).

Nos. 174



112 Providing&Fixing Thermostatic shower column completeand as complete, as directed by Engineer-Incharge (Make:- ROCA/ Equal approved make, Neo Basic Thermostaticshower cloumn, Model No. RP2H035800 ),

Nos. 2

113 Providing&Fixing Thermostatic shower column completeand as complete, as directed by Engineer-Incharge (Make:- ROCA/ Equal approved make, Neos II BasicThermostatic shower cloumn, Model No. RP2H0348000 ),

Nos. 2

114 Providing&Fixing Overhead shower with short / longarm and wall flange complete and as complete, asdirected by Engineer-Incharge (Make :- ROCA/ Equalapproved make,Model: Single flow overhead shower-T9901A1),

Nos. 4

115 Providing&Fixing push type liquid soap dispenser withPVC rawl plug & C.P. brass screw complete as requiredand as complete, as directed by Engineer-Incharge(Make :ROCA/ Equal approved make,)

Nos. 10

Towel Rail & Ring

116 Providing & fixing C.P. brass towel rail with C.P. brasswall brackets & C.P brass screws complete as requiredand as complete, as directed by Engineer-Incharge (Make:- Jaquar/ Equal approved make, Model:- ACN-1111n).

Nos. 183

117 Providing & fixing C.P. brass towel ring with C.P. brasswall brackets & C.P brass screws complete as requiredand as complete, as directed by Engineer-Incharge (Make:- Jaquar/ Equal approved make, Model:-ACN-1121 BN).

Nos. 96

118 Providing & fixing C.P. brass towel with C.P. brass wallbrackets & C.P brass screws complete as required and ascomplete, as directed by Engineer-Incharge (Make :-

Jaquar/ Equal approved make, Model:- QUA - 61723).

Nos. 4

119 Providing & fixing C.P. brass Double coat hook with PVCrawl plug & C.P. brass screw complete as required and ascomplete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:- AKB - 35761).

Nos. 69

120 Providing&Fixing C.P brass toilet paper holder with PVCrawl plug & C.P. brass screw complete as required and ascomplete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:- ACN - 1155N).

Nos. 181

121 Providing&Fixing C.P brass toilet paper holder with PVC

rawl plug & C.P. brass screw complete as required and ascomplete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:- ACN - 1153N).

Nos. 24



122 Providing&Fixing, testing and commissioning of Kitchensink including providing & fixing C.I./M.S. Brackets(duly painted with 2 coats of paint over a coat of primer)C.P. cast brass bottle trap with extension piece, rubberadaptor, wall flange, union, C.P. brass chainrubber plug &making good and as complete, as directed by Engineer-Incharge (Make-Nirali / Equal approved make, ModelNo. C853199, C854399)

Stainless steel sink without drain board. No. 20

123 Supplying and fixing 600 x 450 mm Reflextion mirror ofParryware make or approved equivalent with necessaryscrews, nuts and washer and as complete, as directed byEngineer-Incharge Model:No:C 8608 - Parryware make orapproved equivalent make.

No. 194

124 Providing&Fixing, testing and commissioning of C.P.brass wall / counter mounted Sink Cock with RegularSwinging Casted Spout with Wall Flange complete asrequired and making good and as complete, as directedby Engineer-Incharge (Make :- Jaquar/ Equal approved

make, Model:- FLR-5347N).

No. 115

125 Providing&Fixing solid state, no touch operting, fullyhygienic hand drier of approved shade with

single/double blower, with time delay, summer & wintercontrol, music while drying, volume ON/OFF controlsincluding providing necessary brackets, cable from drierto Plug, Plug top key and lock etc, complete as directed bythe Engineer-incharge.(Make-Eronics / Equal approvedmake, Model No. - EH06S )

No. 10

126 Providing&Fixing, testing and commissioning of C.PCopper connection 450 mm long including nuts andwashers and making connection to fixtures and fittingscomplete as required and as complete, as directed by

Engineer-Incharge (Make :- Jaquar/ Equal approvedmake, Model:- ALD-805B).

No. 389

127 Providing & Fixing, testing and commissioning of C.P.brass angle valve with C.P. wall flange, Nut and Washeretc. complete as required and as complete, as directed byEngineer-Incharge (Make :- Jaquar/ Equal approvedmake, Model:- FLR-5053N).

No. 598

128 Providing, fixing, testing and commissioning of 15 mmdia C.P. brass long body bib cock with C.P. wall flange ofapproved quality and making good as required and ascomplete, as directed by Engineer-Incharge (Make :- Jaquar/ Equal approved make, Model:- CON-107KN).

No. 22

129 Providing and fixing Heavy class SS grating withCockroach proof SS strainer of approved design includingsetting in floor with cement motor to match with floorfinish as per architect requirement & suitable for wasteand FD and as complete, as directed by Engineer-Incharge(Make :- Chilly- India King or equal approvedmake,)

No. 568



130 Providing&Fixing, testing and commissioning ofAdjustable Type of Washbasin 65x35 with one pair ofmounting brackets, EWC and cistern complete withfittings and seat cover, one no hinged rail, 76 cm and fiveno grab rails 60 cm and as complete, as directed byEngineer-Incharge (Make :- ROCA/ Equal approvedmake, Model:-(Carron PP Closet with Antimicrobial seatcover - C0250 + C8094), (Hand Rails 600 - C8154), (HingedArms - C8153), (Plastic cistern - C8157), Indus basin(500*400mm - C0471), (Pillar Cock with Aerator -T1602A1))

No. 4

Total of 'Sanitary Fixtures & Fittings

B COLD WATER SUPPLY

131 Providing and fixing in position Class 'C' GI pipe work forall pump suction / discharge line with common headercomplete with all fittings like elbow, tee, reducer, flange,union etc. conforming to IS:1239 (Part 1) for pipes and IS :1879 (Part 1 to 10) for fittings including fixing in wall /ceiling / floor level, supported by galvanized clamps,hangers, vertical pipe support etc. and as complete, as


a 80 mm dia RMT 10

b 100 mm dia RMT 20

c 150 mm dia RMT 10

132 Providing and fixing CPVC (Chlorinated Poly VinylChloride) water supply pipes confirming to IS:15778/2007with pipe as per CTS SDR 11 (operating pressure - 7 Bar @82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inchto 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6Inch Schedule 40 Pipe to be used . Pipes shall be joinedusing solvent welded CPVC fittings i.e. Tees, Elbows,

Couplers, Unions, Reducers, brushings etc. includingtransition fittings (connection between CPVC & metalpipe/GI) i.e. Brass Adaptors (both Male & Femalethreaded) conforming to ASTM D-2846. ASTM F441 withonly CPVC solvent cement conforming to ASTM F-493.All termination points for installation of faucets shall havebrass termination fittings. Installation shall be to as perTechnical Manual of manufacturer of pipes & fittings.

Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5cm chase in wall and floors for the pipe, making good thesame by using 1:3:6 cement mortar over the wire mesh

and providing protection to embedded pipes and fittings(in wall chase) by wrapping two layers of 400 micronpolythene sheet including proper overlaps on jointscomplete as required.and as complete, as directed byEngineer-Incharge.

a 3/4" dia (20 mm) RMT 3945

b 1" dia (25 mm) RMT 4



133 Providing and fixing CPVC (Chlorinated Poly VinylChloride) water supply pipes as above.Fixing/supporting the pipes (& fittings) at wall/ceilinglevel supported by galvanized clamps, fastener, hangersetc, as per specification. Exposed pipes to be painted oflegends with direction arrow. GI pipe sleeves suitablehigher size shall be provided wherever the pipes arecrossing the fire rated walls / floors slab and sealing thesleeves with glass wool in between and fire sealantcompound at either end and as complete, as directed byEngineer-Incharge.

a 3/4" dia (20 mm) RMT 4

b 1" dia (25 mm) RMT 2735

c 1.1/4: dia (32 mm) RMT 2756

d 1.5" dia (40 mm) RMT 1278

e 2" dia (50 mm) RMT 170

f 2-1/2" dia (65 mm) RMT 2

134 Providing & fixing male/ female screwed end full waylever operated forged brass ball valve of brass body withforged brass hard chromeplated ball & teflon seat testedto a pressure 15 Kg / sqcm with (threaded joints)complete as required and as complete, as directed byEngineer-Incharge

a 20 mm dia No. 2

b 25 mm dia No. 830

c 32 mm dia No. 68

d 40 mm dia No. 33

e 50 mm dia No. 25

135 Providing and fixing C.I. Butterfly valve (Body : GreyCast Iron, shaft : SS, Disc : SG Iron (nickel plated), Liner :HT - EPDM/Nylon) of approved make with flange,washer, nuts & bolts and PN 16 pressure rating including

rubber gasket & painting complete.and as directed byEngineer-Incharge.

a 65 mm dia No. 1

b 80 mm dia No. 2

136 Providing & fixing C.I. wafer type check valve of ratingPN 16 including rubber gasket, flanges, union, nuts, bolts,washers & painting complete as required and as complete,as directed by Engineer-Incharge

a 65 mm dia No. 1

b 80 mm dia No. 2

137 Providing & fixing dual flanged C.I. `Y' Strainer withstainless steel fine wire mesh perforated sheet basket with

necessary flange/ unions nuts, bolts and washerscomplete as required and as complete, as directed byEngineer-Incharge

a 65 mm dia No. 1

b 80 mm dia No. 2



138 Providing and fixing in position of approved quality highpressure rated Gun Metal Float Valve with copper ballfloat and brass rods of required length suitable for testpressure of not less than 15 Kg/sqcm of the followingsizes and as complete, as directed by Engineer-Incharge.

a 25 mm dia No. 5

b 32 mm dia No. 7

c 40 mm dia No. 10

139 Providing and fixing pressure reducing station for coldwater supply comprising of 2 Nos Gun Metal ball valveson inlet & outlet & 1 no. globe valve for by-pass 1 Nopressure reducing valve with flanged/ screwedconnection, 1 No. `Y' strainer, 2 Nos Pressure gauge oninlet & outlet, and 1 No. 15 mm dia safety valve. Thecomplete system is tested to a pressure not less than 15Kg/Sq.cm and suitable to reduce the pressure upto 2Kg/Sq.cm) Including necessary pipe & fittings; i.e.flanges/ unions, nuts, bolts and washers complete asrequired and as complete, as directed by Engineer-

Inchar ea 25 mm dia (Brass Housing - PRV) No. 6

b 32 mm dia (Brass Housing - PRV) No. 74

c 40 mm dia (Brass Housing - PRV) No. 27

140 Providing, fixing , testing and commissioning water metrewith direct reading dial in KL with all necessary fittingsuch as threaded pieces, unions pressure gauge, isolationcock, flanges piece for future removal, flanges / unionscomplete with all necessary testing charges and obtainingtest certificates from municipal authorities and ascomplete, as directed by Engineer-Incharge., on followingsize pipe lines (1 no. strainer shall be provided at inlet &

outlet and cost shall be inclusive for the same).

a 50 mm dia (CI) No. 1

b 65 mm dia (CI) No. 2

141 Providing & fixing Auto Air vent for cold water supplyrisers, suitable for pressure not less than 15 Kg/Sq.cm.

a 25 mm dia No. 22

142 31 Constructing brick masonary chamber (for housingvalves,metres etc.) of brick work with bricks of230X115X75mm class 50 with cement mortar 1:5 (1cement:5 fine sand) plastering internal face & (with a

floating coat of neat cement) cement mortar 1:3 (1 cement:3 fine sand and rough plaster on outer face. R.C.C top slabwith medium duty D.I. manhole cover and frame of600x600 mm (weight : 60 KG). Including excavation,dewatering, refilling, watering, ramming and removingthe surplus excavated material complete as required andas complete, as directed by Engineer-Incharge (All sizesare clear internal sizes).Size 600 x 600 x 600 mm deep No. 3



143 Providing & fixing of LOFT Tank (Make: Sintex, ModelNo:IWS 30.01,Cap-300 lts)(Location :Toilet).as complete,as directed by Engineer-Incharge

No. 202

144 Providing & fixing of SS Tank ( 304 grade ) For RO Watersupply (Cap-500 lts) (Location : Terrace).as complete, asdirected by Engineer-Incharge

No. 4

Total of Cold Water Supply

C - INTERNAL DRAINAGE : (RAIN,SOIL, WASTE &VENT)

145 Providing, fixing, jointing, testing and commissioning ofUPVC pipe conforming to I S 4985 with 6kg/sq.cm. wastepipe from fixture to floor trap cut to required lengthsincluding all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door) & ventcowl. Fixing at wall / ceiling level supported by G.I.clamps, hangers etc. duly epoxy coated. As complete, asdirected by Engineer-Incharge.

a 40 mm dia RMT 596

b 50 mm dia RMT 103

146 Providing, fixing, jointing, testing and commissioning ofUPVC pipe confirming to I S 4985 with 6kg/sq.cm cut torequired lengths including all necessary fittings andspecials such as bends, junctions offsets, access pieces andmaterial and making good the same complete as requiredand as directed by Engineer-Incharge Cost shall beinclusive of providing protection to pipe all round /haunches as per specification. (Running at toiletsunken,shaft, Rain water down take, data cabling &balcon )


b 110 mm dia RMT 4843

c 160 mm dia RMT 1760147 Providing, fixing, jointing, testing and commissioning of

UPVC pipe confirming to IS : 13592, and confirming to IS :4985 (Pipe Class II -6 kg / sq.cm) cut to required lengthsincluding all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door) & ventcowl. Fixing at wall / ceiling level supported by G.I.clamps, hangers etc. duly epoxy coated and as complete,as directed by Engineer-Incharge(Location for Shaft )

a 63 mm dia RMT 656

b 75 mm dia RMT 200

c 110 mm dia RMT 1162

d 160 mm dia RMT 786



148 Providing, fixing, jointing, testing and commissioningUPVC (Class III) Rain water down take pipe conformingto IS:4985 cut to required lengths including all necessaryfittings and specials. Fixing at wall/ceiling levelsupported by galvanized steel clamps & hangers etc.Making proper connection with cement solvent joint asper BIS / manufacturer. Cutting, chases / holes in floors /walls / slab. and as complete, as directed by Engineer-Incharge

a 75 mm dia RMT 737

b 110 mm dia RMT 103

c 160 mm dia RMT 970

149 Supplying and fixing of approved make UPVC multi inletfloor trap with110mm dia inlet & 75mm dia outlet and itis fixed in Sunken slab .and as complete, as directed byEngineer-Incharge.

Nos. 635

150 Supplying and fixing in position of Custom Made P trapof the following sizes from UPVC 6kg/cm2 pipe bymaintaing 50mm water seal including providing

necessary support and as per Specification as complete, asdirected b En ineer-Inchar e.110mm dia inlet & 110mm dia outlet No. 4

151 Providing & fixing rain water `Khurras' size 450x450 mmrequired depth with lead flashing around the pipe withone piece lead sheet of 3 mm thick set on a layer of coldbitumen. Including Heavy duty CI/MS grating as perdrawing complete as required and as directed byEngineer-Incharge

No. 28

Total of Internal Drainage :(Rain,Soil,Waste & Vent)

D - EXTERNAL SEWAGE / STORM WATER

DRAINAGE/WATER SUPPLY:

External Water supply152 Providing and fixing CPVC (Chlorinated Poly Vinyl

Chloride) water supply pipes confirming to IS:15778/2007with pipe as per CTS SDR 11 (operating pressure - 7 Bar @82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inchto 2 Inch. Schedule 40 Pipe to be used from 2-1/2 Inch to 6Inch Schedule 40 Pipe to be used . Pipes shall be joinedusing solvent welded CPVC fittings i.e. Tees, Elbows,Couplers, Unions, Reducers, brushings etc. includingtransition fittings (connection between CPVC & metalpipe/GI) i.e. Brass Adaptors (both Male & Femalethreaded) conforming to ASTM D-2846. ASTM F441 withonly CPVC solvent cement conforming to ASTM F-493.

All termination points for installation of faucets shall havebrass termination fittings. Installation shall be to as perTechnical Manual of manufacturer of pipes & fittings.



Providing and fixing CPVC (Chlorinated Poly VinylChloride) water supply pipes as above.Fixing/supporting the pipes (& fittings) at wall/ceilinglevel supported by galvanized clamps, fastener, hangersetc, as per specification. Exposed pipes to be painted oflegends with direction arrow. GI pipe sleeves suitablehigher size shall be provided wherever the pipes arecrossing the fire rated walls / floors slab and sealing thesleeves with glass wool in between and fire sealantcompound at either end. As complete, as directed byEn ineer-Inchar e.External Water supply

a 1" dia (25 mm) RMT 252

b 1.1/4" dia (32 mm) RMT 401

c 1.1/2" dia (40 mm) RMT 355

d 2" dia (50 mm) RMT 420

e 2-1/2" dia (65 mm) RMT 343

f 3" dia (80 mm) RMT 343

g 4" dia (100 mm) RMT 10

153 Providing, fixing, jointing and testing in position thefollowing UPVC pipes confirming to IS:4985 of 6 Kg /Sq.cm for drainage system cut to required length. Pipe tobe laid below ground level in trenches upto requireddepth including excavation in all kind of soil (hard rock),dewatering, refilling, watering, ramming and removingthe surplus excavated material and making good the samecomplete as required. Cost shall be inclusive of providingprotection to pipe all round / haunches as perspecification and also as complete, as directed byEngineer-Incharge (For sewer and Sullage line)


b 200 mm dia RMT 367154 Providing, fixing, jointing and testing in position the

following UPVC pipes confirming to IS:4985 of 6 Kg /Sq.cm for drainage system cut to required length. Pipe tobe laid below ground level in trenches upto requireddepth including excavation in all kind of soil (hard rock),dewatering, refilling, watering, ramming and removingthe surplus excavated material and making good the samecomplete as required. Cost shall be inclusive of providingprotection to pipe all round / haunches as perspecification and also as complete, as directed byEngineer-Incharge (For storm water line)

200 mm dia RMT 606155 Providing and fixing square mouth cast iron gully trap

complete in brick masonry 300 x 300 mm chamber ofstandard detail with first class bricks and water tightdouble seal CI cover with frame of 300 x 300 mm internalsize. The weight of cover and frame to be not less than 10Kg as per standard design and also as complete, asdirected b En ineer-Inchar e



(Note : Cost shall include excavation dewatering andwatering proofing of chambers as directed at site)300 x 300 mm chamber with 150 x 100 mm size“GULLEY” trap

Set 33

156 Designing and constructing brick masonry inspection

chamber of the following sizes in brick work of class 75 incement mortar 1:5 (1 cement:5 fine sand), R.C.C. top slabwith 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm. nominal size) embeded with frame formanhole, RCC foundation slab. 1:2:4 mix (1 cement : 2coarse sand:4 graded stone aggregate 40 mm nominalsize) both inside and outside of plastering 12 mm thickwith cement motar 1:3 (1 cement : 3 coarse sand) with afloating coat of neat cement on inside face, proper waterproofing to ensure no ground water seepage in themanhole, Poly propylene (conforming to ASTMD - 4101)foot rests (meeting the 224 kg load requirement as per IS5455) at 300 mm spacing, benching and making channelswith 1:2:4 cement concrete neatly finished, includingnecessary centering and shuttering, reinforcement,

excavation, in all kind of soil, dewatering, refilling,watering, ramming and removing the surplus excavatedearth, making good the same complete as required.

Contractor shall submit the structural design anddrawings for the approval of Engineer-incharge prior toexecution.

a 900 x 800 mm size(UP TO 900mm) No. 38

b 1200 x 900 mm size(UP TO 2.4M) No. 19

c 1500mm Dia Circular(2.4 to 3.0m Depth) No. 4

157 Providing & fixing Cast Iron Manhole cover with framein Cement concrete 1:2:4 (one of cement two of sand andfour of hardbroken stone jally) finished neatly etc..ascomplete, as directed by Engineer-Incharge.- For

inspection chamber

a 600 x 600 mm, Heavy Duty (B-125), Wt 115 kg No. 61

158 Designing and constructing brick masonry Rain water

collection chamber for fire protection valve chamber

and for data cabling of the following sizes in brick worksize 230x115x75mm of class 50 in cement mortar 1:5 (1cement:5 fine sand), R.C.C. top slab with 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20mm.nominal size) embeded with frame for manhole, RCCfoundation slab. 1:2:4 mix (1 cement : 2 coarse sand:4

graded stone aggregate 40 mm nominal size) both insideand outside of plastering 12 mm thick with cement motar1:3 (1 cement : 3 coarse sand) with a floating coat of neatcement on inside face,



proper water proofing to ensure no ground water seepagein the manhole, Poly propylene (conforming to ASTMD -4101) foot rests (meeting the 224 kg load requirement asper IS 5455) at 300 mm spacing, benching and makingchannels with 1:2:4 cement concrete neatly finished,including necessary centering and shuttering,reinforcement, excavation, in all kind of soil, dewatering,refilling, watering, ramming and removing the surplusexcavated earth, making good the same all complete asdirected by Engineer-incharge.

a 600 x 600 x 600 mm size No. 34

b 900 x 800 mm size x 900 mm size No. 171

159 Providing & fixing Ductile Iron Manhole cover withframe in Cement concrete 1:2:4 (one of cement two ofsand and four of hardbroken stone jally) finished neatlyetc..as complete, as directed by Engineer-Incharge.- For

Rain water collection chamber

600 x 600 mm, Medium Duty (B-125), Wt 115 kg No. 205

Total of 'External Sewage/Storm Water Drainage/Water Supply

E - CIVIL WORKS / MISCELLANEOUS ITEMS:

160 Providing and fixing 600 mm long MS hot dip galvanizedPUDDLE FLANGES fabricated out of 6 mm thick MSplates of suitable size and IS:1239 heavy class pipesproperly fixed in walls & top slab of tanks. The entirefittings shall be hot dipped galvanized after fabrication.Length shall be minimum 600 mm or wall thickness plus200 mm on either side (which ever is more). etc. ascomplete, as directed by Engineer-Incharge.

a 50 mm dia (flanged ends) No. 62

b 80 mm dia (flanged ends) No. 49

c 100 mm dia (flanged ends) No. 48d 150 mm dia (flanged ends) No. 9

e 200 mm dia (flanged ends) No. 2

161 Providing and fixing electronic type level indicator forwater tanks mounting in panel with the followingfeatures, level display, alarm when water level is low orhigh, full range from one level to four level display andmanual reset for alarm etc. with electrical wiring conduitsupports from wall & ceiling probs and all otheraccessories etc as complete, as directed by Engineer-Incharge.

No. 6

Total of Civil Works/Miscellaneous Items

F - WATER SUPPLY, DRAINAGE, PUMPS &EQUIPMENT

Hydropneumatic System:

162 Supply, Installation, Testing And Commissioning OfCompact Self Contained Skid Mounted HydropneumaticSystem As Follows:

a. In-Line, Multisage, centrifugal pumps with SS-304 casingand impeller and SS-316 shaft, CI base & head TEFCmotor (with mechanical seal)



(Vendor to submit performance curves and technicalcatalog of the proposed model for review & information)

The pump shall be selected for performance at bestefficiency point. However, the pump selection shall besuitable for performance with set point @ + 20% of therated head.Nos. of Pumps : 3 (2W +1S)

Water Flow Rate : 4.09 LPS each

Head : 108 M

Purpose :- Cold water supply

b. Electric control panel with change over swich, relays,electrical wiring, cabling from panel to pumps, levelcontroller complete with all accessories as permanufacturer specification.

c. Complete (Skid mounted wall mounted / floor mounted)electrical control panel comprising of all accessories suchas PLCs, pressure switches, pressure transducers, controlwiring and any other necessary imports etc. (list to beprovided by the vendor)

d. Precharged diaphram pressure vessel with food grademembrane, charging connection, connected to outletheader with necessary flanges, gaskets, isolating valves,nuts/bolts etc complete.

e. Set of accessories such as pressure switches, pressuretransducers, inter connecting power and control cablingetc. complete

f. Accessories like NRVs, isolating valves, SS-304 (non-Magnetic) suction and delivery header, pressure gauge,MS base frame (Synthetic enamel painted over a coat ofprimer)Hydropneumatic System as described above Set 1

163 Supply, installation, testing and commissioning of terrace

Booster pump comprising of the following:

Horizontal mono-block centrifugal pump, suitable foroperation on 415 volts ± 6%, 3 phase, 50 HZ A.C supply.

The pump casing shall be CI, shaft shall be CS & impeller/ shaft sleeve / casing wearing ring shall be bronze. Thesystem shall be complete with necessary pressure gaugewith gun metal shut off cock on delivery side. (The pumpshould meet the condition and shall be gotten approvedby the Local fire Authority).

Squirrel cage induction motor TEFC type for operation on415 V, 3 phase 50 HZ AC supply for the above pump withspeed of 2900 R.P.M.

Suitable cement concrete foundation with plaster, (designand drawing to be provided by the Contractor while thefoundation will be done by others) complete withAntivibration arrangement of cushy foot mounting.

Nos. of Pumps : 2 (1W +1S) Set 5Water Flow Rate : 1.0 LPS each



Head : 25 M

Purpose :- Terrace booster pump

- Submersiable Pumps

Submersiable Centrifugal Non-clog Drainage Pumps

Supply, installation, testing and commissioning ofcontinuous duty submersible centrifugal non-cloggingdrainage pumps complete with 3 phase motor with all

necessary protection and mechanical seal etc.Cost shall beinclusive of auto pumping arrangement. (IW +1S)

164 Flow rate : 3.3 LPS

Head : 25 Mts

Solid Handling : 10-12 MM

Location : Rain water storage sump-1 &2

Purpose : Rain water transfer to Fire water tank.

MOC : CI Body, impeller and SS Shaft Set 2

165 Flow rate : 3.3 LPS

Head : 25Mts

Solid Handling : 10-12 MMLocation: Plumbing Plant Room

MOC : SS body SS Impeller & Shaft Set 1

Total of Water Supply,Drainage,Pumps & Equipment

G - ELECTRICAL INSTALLATION FOR PLUMBING

166 Design, fabrication, assembling, wiring, supply,installation, testing and commissioning of motor controlcentre shall be fabricated out of 14 gauge CRCA sheetsteel in form in 3b formation with reinforcement ofsuitable size angle iron, channel „T‟ sections irons and/orflats wherever necessary. Cable gland plates shall beprovided on top as well as at the bottom of the panels.

Panels shall be treated with all anticorrosive processbefore painting as per specifications with 2 coats of redoxide primer and final approved shade of powder coatedpaint. 2 Nos. earthing terminals shall be provided for 3phase, 4 wire, 50 Hz supply system. Lifting hooks shallalso be provided in case of large panels. Approval shall betaken for each panel before fabrication. Cadmium Platedhardware shall be used in fabrication of panels. Quotedrates shall inclusive of cables (in accordance tospecification) with earthing from panel to each motor /equyipment.

PLUMBING SYSTEM



Design, fabrication, assembling, wiring, supply,installation, testing and commissioning of motor controlcentre shall be fabricated out of 14 gauge CRCA sheetsteel in form in 3b formation with reinforcement ofsuitable size angle iron, channel „T‟ sections irons and/orflats wherever necessary. Cable gland plates shall beprovided on top as well as at the bottom of the panels.Panels shall be treated with all anticorrosive processbefore painting as per specifications with 2 coats of redoxide primer and final approved shade of powder coatedpaint. 2 Nos. earthing terminals shall be provided for 3phase, 4 wire, 50 Hz supply system. Lifting hooks shallalso be provided in case of large panels. Approval shall betaken for each panel before fabrication. Cadmium Platedhardware shall be used in fabrication of panels. Quotedrates shall inclusive of cables, cable trays, control cabling,cabling, earthing (in accordance to specification) withearthing from panel to each motor / equipment.

a - MCC –1 (Plumbing Panel)- Incoming

100 amps TPN MCCB with the following accessories:

a. 0-500 volts 96 x 96 mm square voltmeter with selectorswitch protected by 2 amps TP MCB. 1 Setb. 0-200 amps 96 x 96 mm square ammeter with selectorswitch and 200/5 amps 10 VA CL:1 CTs. 1 Set

c. Phase indicating lamps protected by 2 amp SP MCB 3Sets

- Bus Bar

125 amps TPN (25 KA) aluminium bus bar with heatshrinkable insulation sleeves.

- Outgoings

a. 1 No. 32 amps TPN MCCB outgoing feeder to ROWater Hydro-pneumatic.b. 1 No. 63 amps TPN MCCB outgoing feeder to DomesticWater Hydro-pneumatic.c. 2 No. 32 amps TPN MCCB for 3 HP DOL starter andoutgoing feeder to Water treatment pump motor(including 1nos. standby). Each compartment shallcontain auto / manual selector swtich and indicating /pushbutton lamps with MCB for ON / OFF / TRIP ofmotor.d. 2 No. 32 amps TPN MCCB for 2 HP DOL starter and

outgoing feeder to plumbing plant room drain pump(including 1nos. standby). Each compartment shallcontain auto / manual selector swtich and indicating /pushbutton lamps with MCB for ON / OFF / TRIP ofmotor.



e. 4 No. 32 amps TPN MCCB for 5 HP DOL starter andoutgoing feeder to Storm water transfer pump (including1nos. standby). Each compartment shall contain auto /manual selector swtich and indicating / pushbuttonlamps with MCB for ON / OFF / TRIP of motor. (Note : -Starter to be located at near storm water sump. so seprateencloser required for starter with all nessacery items.)

f. Spare MCCB‟s of following capacities:

i. 32 amps TPN MPCB‟s 2 Nos.

iii. 63 amps TPN MPCB‟s 1 Nos.

Necessary cable alleys, internal wiring, andinterlocking, earthing for all equipment shall also beincluded.

- Notes :

a. All MCCBs shall be of 25 KA breaking capacity andsuitable for motor duty application.b. Provision shall be made for providing potential freecontacts to all pumps starters for connection to BAS

c. Provision shall be made to ensure system protectionfrom dry running of the pumpMCC - 1 (Plumbing panel) as described above. Set 1

Total of Electrical Installation for Plumbing

167 Water Treatment Plant-90,000Liter/Day

Providing, Installing, testing and commissioning of SS

vertical centrifugal pump. Each pump shall have TEFC2900 RPM three phase electric motor. The pump shallhave cast iron head, base plate SS Shaft / Impeller /Intermediate chamber. Pump shall be provided withmechanical seal. The pump shall be suitable for auto /manual operation. The installation shall be complete with

all necessary ancillaries & accessories including base platecomplete as required. (1Working + 1Standby).

Flow rate : 11250 LPH each

Head : 30 Mts

Required for : Raw water treatment for Feed pump

Providing, Fixing, Testing & Commissioning of verticalMSEP filter with adequate dirt holding capacity.Fabricated from MS sheet as per manufacturer'sspecifications complete with initial charge filter mediaincluding painting inside with two coats of non toxicepoxy and with one coat of zinc chromate two coats of

synthetic enamel paint outside. Including concretefoundation with cement plaster complete as required. Thefilter shall also be provided with set of internals for rawwater inlet and bottom collecting system. Complete withfrontal piping (heavy) and butterfly valves designed on1.50 m / sec velocity.

Pressure Sand Filter for Domestic Water services.

Filtration Rate 15000L/Sqm/Hr

Working pressure 3 Kg/Sq.cm



Capacity : 11250 LPH

Activated Carbon Filter

Filtration Rate 15000L/Sqm/Hr

Working pressure 3 Kg/Sq.cm


Providing, Fixing, Testing & Commissioning of MSEP

water softening plant (suitable for 3 Kg/Sqcm working

pressure) complete with initial charge with T-40 NAResin, multiport valve with built in ejector for controllingall operations), regeneration system and HDPE tank,pressure gauge at inlet, outlet and back wash (each withisolation cock), valves, fittings and water hardness testingkit & associated works. Softener shall be suitable for thefollowing duty:Raw water hardness 800 Mg/L

Treated water harness 100 Mg/L

Regeneration Period 8 Hrs.


Providing, Installing, testing and commissioning of

dosing system (for domestic water treatment plant)consisting of one HDPE tank of 100 liters capacity with apositive displacement diaphragm dosing pump havingvariable flow rate of 0-4 lph. The motor shall be suitablefor operation at 240 V/Single phase/50 Hz. Supply. Thepump shall be supplied complete with necessarypolypropylene piping, valves, strainers, low level switchand injection fittings. The pump shall be speed & strokecontrol Asia LMI / equivalent make.

The cost shall be inclusive of providing salt for the testingand operation of system before handover to the owner.

Supply, installation, testing & commissioning of HighFlow UV system for tertiary water treatment. The UVchamber shall be internally & externally electro polishedwith double side flange, drain part & probe bar. The unitshall use quartz glass technology for superior UVtransmission and specialized high intensity UV lamprated for 16000 hour operation. The UV dosage shall begreater than 30,000 uW-Sec / sq.cm system to be completewith monitoring units.Unit flow : 90 Cum / Day ( 11.25 KL/hr)

Providing, Fixing, Testing & Commissioning of pressure

switch for water pumps to start/stop the pump at set

pressure. Including wiring, cabling from pump to panel &all other accessories as required to operate the systemautomatically.



Providing, Fixing, Testing & Commissioning of thefollowing heavy class GI pipes conforming to IS:1239 cutto required lengths including all necessary fittings(conforming to IS:1879) and specials such as bends, tees,unions, reducers, flanges & plugs etc. fixing at wall /ceiling level supported by clamps, hangers etc, (to begalvanized after fabrication) cutting hole in wall / floor /slab and making good the same good with cementconcrete 1:2:4 / fire sealant complete as required.

Painting two coats of Synthetic enamel paint ofapproved shade on pipes and supports as per pipe colorcode over a coat of primer. Including painting of legendswith direction arrow as per the approval of the Engineer-Incharge.Providing, Installation, testing and commissioning oftanker inlet connection complete with 80 mm dia GI inletpiping, hose inlet connection, MS cabinet enclosure(epoxy painted after fabrication), pad lockingarrangement, inlet flexible hose complete with all

necessary arrangement.Providing, Fixing, Testing & Commissioning of butterfly

valve (Body : Grey Cast Iron, Shaft : SS, Disc : SG Iron(Rilson coated), Liner : HT - EPDM) (up to 150mm diawith hand lever operation & above with gear boxoperation). Tested to a pressure not less than 15Kg/Sq.cm. Including rubber gasket, flanges, nuts, bolts,washers & painting complete as required.Providing, Fixing, Testing & Commissioning of CI wafer

type check valve tested to a pressure of 15 Kg/sqcm.Including rubber gasket, flanges, union, nuts, bolts,washers & painting complete as required.

Providing, Fixing, Testing & Commissioning of CI `Y'Strainer (screwed/ flanged) with stainless steel fine wiremesh perforated sheet basket with necessary flange/unions nuts, bolts and washers complete as required (onpump suction).

Providing, Fixing, Testing & Commissioning of on lineturbine type flowmetre with preamplifier electronicflowmetre mounted in plumbing plant room electricalcontrol panel with the following features. Monitoring thetotal flow, Flow rate, high low arm batching and blendingetc. Including electrical wiring from preamplifier tomicroprocessor based flowmetre. Complete with all typeof Plumbing & Electrical connections, accessories, wiring,

conduits & supports complete with all respect.

Providing, Fixing, Testing & Commissioning of Heavy

class header complete for pump suction / dischargemanifold comprising of expansion bellows, flanges,unions, check nuts, tee elbow etc. including all flangedconnections as per drawing / site requirement. Supportsfrom wall, floor and ceiling etc. Including dead endflanged connection complete as required.



Rate shall include all the above works / specification asdirected by Engineer-incharge.

Set 1

Total of WTP

168 RO TREATMENT Plant Capacity of 2000 Liter/Day

Supply, installation, testing and commissioning of 500liters/day @ 4hr per day capacity of RO plant and suitableFilter Feed pump, Pressure Sand Filter, Activated Carbon

Filter, antiscalant dosing system, reverse osmosis systemsikd mounted, high pressure pump, membrane pressurevessel, Ro membrane with CIP system , ph correctiondosing system, Pressure Gauge, Flowmetre, Piping,Electrical panel and cable etc...

Note :- 1. Outlet water from the RO plant meeting thedrinking water quality requirement with chemicalparameters in acceptable limits as per the : IS 10500, 1991,2. and also all pumps are provide ( 1 work +1 standby ).


Supply, Installation, Testing And Commissioning Of

Compact Self Contained Skid Mounted HydropneumaticSystem As Follows:In-Line, Multisage, centrifugal pumps with SS-304 casingand impeller and SS-316 shaft, CI base & head TEFCmotor (with mechanical seal)(Vendor to submit performance curves and technicalcatalog of the proposed model for review & information)

The pump shall be selected for performance at bestefficiency point. However, the pump selection shall besuitable for performance with set point @ + 20% of therated head.Nos. of Pumps : 2 (IW +1S)


Head : 108 M

Purpose :- RO water supply Set 1

Total of RO Treatment

169 Sewage Treatment Plant Capacity of 2, 50,000Litres/Day,

Design, supplying, installing, testing &commissioning of Sewage Treatment Plant

(excluding excavation, back filling & disposal of surplusearth Civil construction work) for the followingduty:

Nature of effluent - Domestic Sewage fromresidential toilets & kitchens.Daily average flow - 225 KldpH - 7.5 – 8.5

BOD5 - 250 – 400 Mg/L

S. Solids - 150 – 200 Mg/L

COD - 300 – 600 Mg/L

Oil & Grease - 50 Mg / L

Effluent discharge standard after treatment



pH - 6.0 – 8.5

BOD5 - Less than 5 Mg/L

S. Solids - Less than 5 Mg/L

COD - Less than 30 Mg/L

Oil & Grease - Less than 5 Mg/L

Sewage treatment plant shall include the following

items:

Screen ChamberSewage equalization tank/sump

Aerobic MBBR Reactor Floating Media

Secondary Clarifier tank

Flocculator

Tertiary Clarifier Tank

Sludge holding tank

Air Blowers, Pumps & equipment

Screw Pump & Filter Press

Piping, valves etc

Electrical Panel & Cabling

Flushing / Irrigation water storage tankCommon plant room adjacent to STP.

Multigrade sand filters and Activated carbon filters.

Supply, installation, testing & commissioning of 2 NosStainless Steel Coarse & Fine Perforated Screen withsuitable lifting arrangement (size 600 mm wide x 1000mm high approx)Supply of MS hot dip galvanized puddle flanges inaccordance to BS:10 table D as required to be provided (inthe structural slab and wall) of various diameters. Puddleflanges shall be provided for all the structuralcomponent of the STP. The installation of the puddleflanges shall be carried out by the Civil contractor in

accordance to the Civil GA drawing (to be prepared bythe STP contractor) at the required levels & position;under the supervision of the STP contractor

Supply of plastic manhole step/foot rest (@ 300 mm c/C)with polypropylene compound injection molded around12 mm dia (Fe-415) steel reinforcing bar. Provision of thefoot rest is envisaged in various tanks/ components of theSTP for the purpose of accessibility. The installation of thefoot rest shall be done by the civil contractor as per civilGA drawinSupply, installation, testing & commissioning of CImedium duty rectangular manhole cover with frame forthe feasibility of access in the tankSize : 600 x 600 (175 kg)

Supply of vent pipes of 100 mm dia with mosquito proofgrating suitable for the ventilation purpose of the varioustanks



Supply, installation, testing & commissioning of electronictype level controller for automatic operation of the systemwith high/low level alarm complete with auxillaryNO/NC contacts for Raw Sewage Pumps

Contractor shall ensure submission of detailed GA

drawings (Plan & Section), P & I diagram, schematic

diagram for the above mentioned component and

additional component if so required for the completeworking of the STP and got it approved by the Engineer

Incharge.

Supply, installation, testing & commissioning of nonclogging type pumps capable of handling solids upto 38mm having CI casing & impeller complete with allaccessories, motor of required capacity. Delivery headerwith isolation valve, pressure gauge on delivery line withisolation cock, level controller (with wiring) to control thelevel of sump automatically. Pumps shall have followingdut :Submersible Sump Pumps (1W + 1S)

Flow rate (each) = 11.25 cum / hrHead = 10 Mtr

Plant room sump pump with CI body & CI impellerpump(1W + 1S)

Flow rate (each) = 5 cum / hr

Head = 15 Mtr

(Solid handling size for this pump shall be 8 to 15 mm).

Cost shall be inclusive of PVC flexible Hose pipe ( forpiping submeged in effluent) with PVC/GI piping (forpiping non-submerged in effluent)

Provision of guide ropes to guide submersible pump fromupper level to operational level in sump basin withchannels / angle section shall be made by the STPcontractor. (If Required)Contractor is requested to submit quote rate for abovepumps with CI Casing & SS impeller, material ofconstruction.Air diffusion system shall include the following:

Twin lobe rotary air blowers capable of delivering 450cum/hr. of free air at 0.5 kg.cm2. driven through “V” beltor directly coupled through flexible coupling to aTEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3

phase, 50 cycles A/C supply (1W +1S). Blower to behoused in an acoustically treated room such that theiroperating noise does not exceed 80 DB at 3 mtrs. from theblower enclouser.Air piping shall comprise of pipes droppers/ laterals withGI Header complete with all fittings such as tees, crosses,plugs, sockets, elbows, reducers, supports & clamps,puddle flanges etc . Contactor to submit detailed P & Iindicating their proposal.



Non clog type air dispersion system . Air dispersion gridshall be assembled in modular form so that they can bereplaced / repaired easily from plat form at the top.

Supply of MBBR media consisting of Virgin PE carriermodules with Surface are not less than 500 M2/M3

Bronze Ball valve and air dispersion grid as required forSTP as described above.Note :

Air dispersion system shall be provided for SewageSump, Aerobic digester cum Thickner & Aeration Tank.

Providing and fixing all piping (as described below) andisolation control valves for making the system complete.

SS /GI / PVC : Submerged air piping

GI : Air piping

PVC Piping : Pumped effluent , tank overflow pipe line &Process Piping .

GI Heavy : Interconnecting pipe line after deliveryheader of pump/ filterDesigning, supplying, providing, fixing, testing andcommissioning of STP as mentioned above.Supplying, installation, testing and commissioning ofhorizontal sludge recirculation pumps coupled withmotor of capacity 10 cum/hr at 10 m head of C.I. Partsand mechanical seal complete with isolation and non-return valves. (1working + 1 standby)Capacity : 10 cum/hr

Head : 10 M

Supplying, installing, testing & commissioning of

Horizontal centrifugal filter feed water pumps CIImpeller along with motor, pressure gauge with isolationcock, Isolation valve, NRV on delivery line. Isolationvalve, strainer at suction.Mechanical seal, suitablevibration elimination pads of approved design, drain pipewith valve (25 dia.) for the pump. The pump shall besuitable for 415±10% volts 3 phase AC supply (solidhandling size for this pump shall be - 5 mm) (1W + 1S).

Capacity : 11.25 cum/hr

Head : 30 M

Supplying, installing, testing and commissioning ofcentrifugal Horizontal water supply pump C.I Body, CI

Impeller with mechanical seal along with motor. Pressuregauge with isolation cock, NRV, Isolation valve ondelivery line. Isolation valve, strainer at suction. Suction &delivery header (sized at velocity of 1.5m/sec.). Suitablevibration elimination pads of approved design for thepump. The pump shall be suitable for 415±10% volts 3phase AC. Supply.Capacity : 2 LPS (1W + 1S)

Head : 50 M



Purpose : Irrigation water transfer

pumpNote

Operation of pump shall be based on level controllerproposed to be installed in tank as per site location. Thecontractor to recheck the Head required for pumps as persite conditions and provide accordingly.

Supplying, installing, testing and commissioning ofcomposite MSEP vessel filter with MS frontal piping.Filter shall be suitable for working pressure of 5 kg / cm2and shall include media, standard fittings like pressuregauges, sampling cock, backwash, rinse drain, vacuumbreaker, including multiport valve, &1 no. waterflowmetre at outlet (flowmetre shall be approved by dept.of wei hts & measures).Multigrade pressure sand filter

Flow rate : 11..25 cum/hr (1W)

Filtration velocity 15000 Ltrs./ Hr./ Sq.m.

Activated Carbon Filter

Flow rate : 11..25 cum/hr (1W)Filtration velocity 12000 Ltrs./ Hr./ Sq.m.

Supply, installation, testing & commissioning of HighFlow UV system for tertiary water treatment. The UVchamber shall be internally & externally electro polishedwith double side flange, drain part & probe bar. The unitshall use quartz glass technology for superior UVtransmission and specialized high intensity UV lamprated for 16000 hour operation. The UV dosage shall begreater than 60,000 uW-Sec / sq.cm system to be completewith monitoring units.Unit flow : 11.25 Cum / hr

Supply, installation, testing & commissioning of polyelectro type dosing system comprising of 100 ltrs HDPEtank with 0-6 lph electronicmetreing type pump and SSagitator complete with motor.Supply, installation, testing & commissioning of singlescrew double stage, flanged end, CI body alloy steel screwand rotateing parts, pump to filter press 400 LPH 60 mtr.head complete.Supply, installation, testing & commissioning of Manual

closing mechanism filter press comprising of CI bodygrade FG 20, polypropylene plate with sludge cakeholding capacity of 650 ltrs.



Providing, fixing, testing and commissioning watermetrewith direct reading dial in KL with all integral parts ofgun metal or brass with necessary fitting such as threadedpieces, unions pressure gauge and isolation cock, flangespiece for future removal, flanges / unions complete withall necessary testing charges and obtaining test certificatesfrom municipal authorities, on following size pipe lines (1no. strainer & 2 nos. pressure gauges shall be provided atinlet & outlet and cost shall be inclusive for the same).

50 mm dia

Total of STP Works

WATER SUPPLY, DRAINAGE, PUMPS &

EQUIPMENT


Supply, Installation, Testing And Commissioning OfCompact Self Contained Skid Mounted HydropneumaticSystem As Follows:In-Line, Multisage, centrifugal pumps with SS-304 casing

and impeller and SS-316 shaft, CI base & head TEFCmotor (with mechanical seal)(Vendor to submit performance curves and technicalcatalog of the proposed model for review & information)

The pump shall be selected for performance at bestefficiency point. However, the pump selection shall besuitable for performance with set point @ + 20% of therated head.Nos. of Pumps : 3(2W+1S)


Head : 107 M

Purpose :- Flush water supplyApproval from pollution board at initial & various otherstages of works including preparation of report /drawings as per pollution board requirementarrangement of raw sewage testing & commissioning.Contractor shall include the cost of all chemicals(consumed during testing & commissioning) and the costof such items of works which are not explicitly mentionedabove, but are mendatory to have pollution boardapproval.(Consent to operate only)

Total of Water Supply,Drainage,Pumps & Equipment

Works

170 Elecrtical Installation for Sewage Treatment Plant

Control Panel for Sewage Treatment Plant



Design, fabrication, assembling, wiring, supply,installation, testing and commissioning of motor controlcentre shall be fabricated out of 14 gauge CRCA sheetsteel in form in 3 formation with reinforcement of suitablesize angle iron, channel „T‟ sections irons and/or flatswherever necessary. Cable gland plates shall be providedon top as well as at the bottom of the panels. Panels shallbe treated with all anticorrosive process before painting asper specifications with 2 coats of red oxide primer andfinal approved shade of powder coated paint. 2 Nos.earthing terminals shall be provided for 3 phase, 4 wire,50 Hz supply system. Lifting hooks shall also be providedin case of large panels. Approval shall be taken for eachpanel before fabrication. Galvanised hardware with zincpassivation shall be used in fabrication of panels.

MCC-1 (STP Motor Control Centre)

Incoming


a. 0-500 volts 96 x 96 mm square digital electronicvoltmeter with selector switch shall be protected by 2amps TP MCB. 1 Setb. 0-100 amps 96 x 96 mm square digital electronicammeter with selector switch and 100/5 amps 15 VA CL:1 CTs. 1 Setc. Phase indicating lamps shall be protected by 2 amp SPMCB 3 SetsBus Bar

125 amps TPN (25 KA) copper bus bar with heatshrinkable insulation sleeves.Outgoing

a. 2 Nos. suitable rating MPCB for 2.0 HP direct on linestarter and outgoing feeder to EQT sewage transfer

pumps motor - Main (including 1nos. standby). Eachcompartment shall contain auto / manual selector switchand indicating / pushbutton lamps with MCB for ON /OFF / TRIP of motor.

b. 2 Nos. 63A MCCB for 10.0 HP Star delta starter ndoutgoing feeder to air blowers (including 1 no. standby).Each compartment shall contain auto/manual selectorswitch and indicating lamps with MCB‟s for„ON/OFF/TRIP' status of motor.

c. 2 Nos. suitable rating MPCB for 1.0 HP direct on line

starter and outgoing feeders to sludge recirculationpump (including 1 no. standby). Compartment shallcontain auto/manual selector switch and indicatinglamps with MCB‟s for „ON/OFF/TRIP‟ status of motor.



d. 2 Nos. TPN MPCB for 3.0 HP direct on line starter andoutgoing feeders to (1W+1S) filter feed pump. Eachcompartment shall contain direct operated digitalammeter of 0-63 amps range, auto/manual selector switchand indicating lamps with MCB and „ON/OFF/TRIP‟

status of motorf. 1 No. suitable rating MPCB for 1 HP direct on linestarter and outgoing feeders to Helical Screw Pump.Compartment shall contain auto/manual selector switchand indicating lamps with MCB‟s for „ON/OFF/TRIP‟

status of motor.g. 1 Nos. 40A TPN MCCB for 6.5 HP direct on line starter(2W+1S) and outgoing feeders to fluhing water supply

by hydropnumatic system. Each compartment shallcontain C T operated 0-63 amps range digital ammeterwith selector switch, auto/manual selector switch andindicating lamps with MCB‟s and „ON/OFF/TRIP‟ statusof motor

h. 2 Nos. TPN MPCB for 5 HP direct on line starter(1W+1S) and outgoing feeders to irrigation pump. Each

compartment shall contain C T operated 0-32 amps rangedigital ammeter with selector switch, auto/manualselector switch and indicating lamps with MCB‟s and„ON/OFF/TRIP‟ status of motor

e. 2 Nos. TPN MPCB for 1 HP direct on line starter andoutgoing feeders to (1W+1S) plant room floor drian pit

pump. Each compartment shall contain direct operateddigital ammeter of 0-32 amps range, auto/manual selectorswitch and indicating lamps with MCB‟s and„ON/OFF/TRIP‟ status of motor

n. Spare of following capacities:

i. 32 amps TPN MCCB 2 Nos.

ii. 63 amps TPN MCCB 1 Nos.o. Necessary cable alleys, internal wiring, andinterlocking, earthing for all equipment shall alsoincludedNotes:

a. All MCCBs shall be of 25 KA breaking capacity andsuitable for motor duty application.b. All motor starter shall be provided with Automaticlevel controller.c. Provision shall be made for providing potential freecontacts to all pumps starters for connection toBAS

MCC-1 for Upper Level STP as described aboveCABLE & CABLE TRAYS

Supplying, laying & suitable no.of termination offollowing 1100 volt grade PVC sheathedaluminum/copper conductor armoured cables as perspecification in existing trenches, cable trays, ducts overbed of sand, clamped to wall with suitable clamps,saddles fixing bolts including connecting testing andcommissioning.4 core 4 sq. mm copper cable



4 core 6 sq. mm copper cable

3 core 2.5 sq. mm copper cable

3 core 4 sq. mm copper cable

Supply and fixing of perforated type GI cable trays withsupports, hangers, fastners of the following sizes as perspecification.300 mm x 40 x 40 x 2 mm thick

200 mm x 40 x 40 x 2 mm thick150 mm x 25 x 25 x 2 mm thickEARTHING

Supply and fixing of following bare GI tapes / wiresincluding all necessary fixing accessories and effectingconnections as per specifications.25 x 6 mm thick GI strip.

8 SWG GI wire Set 1

Total of Electrical Installation for STP Works

171 Solar Hot Water system-capacity - 13000 Liters/day

Supplying, fixing, testing & commissioning of blackpainted copper collector panel (each panel capcity 200

liter / day) housed in aluminum casing with top of glassshall be as per specifications including all requiredstructural support, necessary inter connecting piping,drain point with valve auto air vent valve etc. complete asre uired.(Note : Civil work to be executed by other agency underrequirement of Solar Hot water Heating Contractor.However this vendor to provide details of all such civilrequirements & also ensure his supervision during thecivil works execution).Solar Water Storage Cum Calorifier Tank :

Supply, installation, testing & commissioning of SS 304horizontal / vertical Solar hot water storage cum

calorifier tank (Capacity 1000 Lts) suitable for minimum8 Kg /Sq.cm working pressure and having SS-304 tube forheat exchange of ____ Kcal/Hr heat transfer capacity,duly mounted by removable type SS-304 flange withgasket, nuts & bolts. Tank shall be provided inlet / outlet,overflow / drain connection with MH cover (550 mm I.D.)pressure relief valves, thermometer at inlet / outlet. Allthe valves & accessories shall be suitable for an operatingpressure as mentioned above. Tank shall be mounted on450 mm high steel structural supports with access ladderpainted with 2 coats of red oxide paint.



Supply, installation, testing & commissioning of SS 304horizontal / vertical Solar hot water storage cum

calorifier tank (Capacity 450Lts) suitable for minimum 8Kg /Sq.cm working pressure,duly mounted by removabletype SS-304 flange with gasket, nuts & bolts. Tank shall beprovided inlet / outlet, overflow / drain connection withMH cover (550 mm I.D.) pressure relief valves,thermometer at inlet / outlet. All the valves & accessoriesshall be suitable for an operating pressure as mentionedabove. Tank shall be mounted on 450 mm high steelstructural supports with access ladder painted with 2coats of red oxide paint.

Tank shall be insulated as per specification, including 24gauge aluminium cladding. The flanges shall be of SS 304with dimensions confirming to AN SI, B 16.5 No. 150. Thenozzles shall be SS ERW pipes. (Tank shall be fabricatedas per unfired pressure vessel code IS 2825-1969, IS 226 /IS 2062).Hot water mixing tank complete with insulation & MS

supporting structure with access ladder duly paint withred oxide.Cold Water inlet Suitable pipe dia with PN 1.0 ButterflyValve.Cold Water inlet line Suitable pipe dia with Check Valve.

inlet / outlet connections for solar system.

Suitable pipe dia with PN 1.0 Butterfly Valve.

Hot water outlet connection to Mixing tank

Suitable pipe dia with PN 16 Butterfly Valve.

Spare outlet 50 mm dia PN 16 Butterfly Valve

Tank Drain connection 25 mm Ball Valve

Temperature sensor at calorifier tank suitable fordifferential temperature setting shall be made for start /stop of the water recirculation pump. The control /system shall be complete with necessary cabling / wiringalong with support.Providing, fixing, jointing and testing in position thefollowing dia of copper pipes confirming to BS2871(Table X) with ISR, Endex, Endbraze fitting confirming toBS:864 part 2 such as copper tees, crosses, plugs, elbows,reducers, union sleeve pieces etc. Cutting hole in wall /floor / slab and making good the same. Cost shall beinclusive of Fixing/supporting the pipes (& fittings) atwall/floor level supported by galvanized clamps, hangers

etc, as per specification. Exposed pipes to be insulated(seprate item) and painting of legends with directionarrow on insulation.



Providing and fixing CPVC (Chlorinated Poly VinylChloride) water supply pipes with pipe as per CTS SDR11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 80 Pipeto be used from 2-1/2 Inch to 6 Inch. Pipes shall be joinedusing solvent welded CPVC fittings i.e. Tees, Elbows,Couplers, Unions, Reducers, brushings etc. includingtransition fittings (connection between CPVC & metalpipe/GI) i.e. Brass Adaptors (both Male & Femalethreaded) conforming to ASTM D-2846. ASTM F441 withonly CPVC solvent cement conforming to ASTM F-493.Cost shall be inclusive of Fixing/supporting the pipes (&fittings) at wall/ceiling level supported by galvanizedclamps, hangers etc, as per specification. Exposed pipes tobe insulated (seprate item) and painting of legends withdirection arrow on insulation.

Providing, fixing, jointing and testing in position thefollowing heavy class (Class C) G.I. pipes for HWS/HWR

conforming to IS:1239 cut to required lengths including allnecessary fittings (All fittings shall confirm to IS:1879 -part 1 to 10) and specials such as bends, tees, unions,reducers, flanges & plugs etc. Threading, jointing, andmaking proper connections. Cost shall be inclusive ofFixing/supporting the pipes (& fittings) at wall/floorlevel supported by galvanized clamps, hangers etc, as perspecification. Exposed pipes to be insulated (seprate item)and painting of legends with direction arrow oninsulation.

Providing and fixing nitrle rubber insulation on hotwater supply / return pipes.

Providing and fixing proprietary polyshield outermechanical protection ON nitrile rubber insulation

comprising of wrapping with poly glass tape helicallywound and subsequently applying 2 coats of polyshieldmaterial (resin & hardner) as per manufacturersspecification and approved by Project Manager /Consultnats.Providing and fixing forged brass ball valves with brassball / stem, union/flange, washer, nuts & bolts. Rated totemperature of 85 Deg C and tested to a pressure not lessthan 16 Kg/Sq.cm. Including covering with nitrile rubberinsulation having protective coating against mechanicaldamage as per manufacturer‟s specification (GI boxing tobe provided).

Providing & fixing dial type (100 mm) pressure gaugewith isolation ball valve suitable for working pressure of250 PSI. Cost shall be inclusive of providing any shortpieces, nipples, elbows etc as required.

Providing and Fixing of Temprature Gauges withisolation valve suitable for system Temprature.



Providing and fixing auto air vent for Hot water supplysystem suitable for pressure not less than 15 Kg / Sqcmincluding water expension tank of 100 mm dia. & 400 mmlong expension tank complete as requitrd.

Providing, installation, testing and commissioning offollowing insulated pumps suitable for 415 Voltsconnected with T.E.F.C. induction motor, M.S. channel,base plate with nuts & bolts complete with vibrationisolators, isolating valve on suction and discharge, nonreturn valve on discharge, pressure gauges with stop cockand dial type thermometer on suction or discharge,necessary Termination with connecting cable from pumpto electrical panel, lugs, earthing wire, cable tray etc. Thepump shall have mechanical seal. The pump shall be SS -304 casing, impeller, shaft and CI (Epoxy coated) base(suitable for hot water temperature).

Flow - 33 LPM

Head - 30 Mtr

HEAT PUMP HOT WATER SYSTEMSupplying,fixing, testing and commissioning, Air to waterheat pump of with LCD display thermo controller & tankprobe .the heat pump outer surface should be millfinished painted alluminum cabinet provides corrosionand having ss condensation pan . the heat pump shoul behaving scroll type copland make compressor , with high& low pressure switch protection with lakout realy &thermal motor protection againest over heating. heatpump should having factory installed inbuilt auto on/offcirculation pump for condensor side. & 15 paskal staticpressure centrafigul fan for Evaporator side. And havingheating capacity 9.5

KW and colloing capacity around 6 KW the COP isaround 3.6 the heat pumps should be suitable for 240voltas , 50 Hz, power supplay operations.SOLAR PUMP STATIONS

Pump Station with intergraded automatic LCD controller& Temperature sensors with internal temperature sensorcables with probes & suitable for single phase 230 volts,50 Hz. -.Leading & positioning of tanks, solar panels etc. -1set

Commissioning & Handing over charges for Electricl withsolar system -1 set

Freight -Chennai to site - 1jobFreight -Chennai to site - 1job



Providing, installation, testing and commissioning offollowing insulated hot water recirculation pumpssuitable for 415 Volts connected with T.E.F.C. inductionmotor, M.S. channel, base plate with nuts & boltscomplete with vibration isolators, isolating valve onsuction and discharge, non return valve on discharge,pressure gauges with stop cock and dial typethermometer on suction or discharge, necessaryTermination with connecting cable from pump toelectrical panel, lugs, earthing wire, cable tray etc. Thepump shall have mechanical seal. The pump shall be SS -304 casing, impeller, shaft and CI (Epoxy coated) base(suitable for hot water temperature).(1 W + 1 S)

Flow - 15 LPM

Head - 30 MtrELECTRICAL INSTALLATION FOR SOLAR SYSTEM

Design, fabrication, assembling, wiring, supply,installation, testing and commissioning of outdoor type

motor control centre shall be fabricated out of 14 gaugeCRCA sheet steel in form in 3b formation withreinforcement of suitable size angle iron, channel „T‟

sections irons and/or flats wherever necessary includingnecessary civil foundation. Cable gland plates shall beprovided on top as well as at the bottom of the panels.Panels shall be treated with all anticorrosive processbefore painting as per specifications with 2 coats of redoxide primer and final approved shade of powder coatedpaint. 2 Nos. earthing terminals shall be provided for 3phase, 4 wire, 50 Hz supply system. Lifting hooks shallalso be provided in case of large panels. Approval shall betaken for each panel before fabrication. Cadmium Platedhardware shall be used in fabrication of panels. rateincludes all power, control cables and cable trays with allnecessary item.

MCC

Incoming


a. 0-500 volts 96 x 96 mm square digital electronicvoltmeter with selector switch through 415 V/ Ö : 3 110V/ Ö 3 PT primary and secondary of PT‟s shall beprotected by 2 amps TP MCB. 1 Setb. 0-63. amps 96 x 96 mm square digital electronic

ammeter with selector switch and 63 / 5 amps 10 VA CL:1CTs. 1 Setc. Phase indicating lamps through 415/110 V PT primary& secondary of PT‟s shall be protected by 2 amp SP MCB3 SetsBus Bar

100 amps TPN (25KA) aluminium bus bar with heatshrinkable insulation sleeves.Outgoings



a. 1 Nos. 40 amps TPN MCCB with 1 Nos. 6 KW DOLstarter to Heat Pump. Each compartment shall contain CToperated digital electronic ammeter of 0-40 amps rangewith auto/manual selector switch and indicating lampswith MCB‟s and „ON/OFF/TRIP‟ status of motor

a. 2 Nos. 32 amps TPN MCCB with 2 Nos. 4 KW DOLstarter to Hot water recircua;ltion pump. Eachcompartment shall contain CT operated digital electronicammeter of 0-32 amps range with auto/manual selectorswitch and indicating lamps with MCB‟s and„ON/OFF/TRIP‟ status of motora. 2 Nos. 16 amps TPN MPCB with 2 Nos. 1.5 KW DOLstarter to solar sun pump. Each compartment shallcontain CT operated digital electronic ammeter of 0-16amps range with auto/manual selector switch andindicating lamps with MCB‟s and „ON/OFF/TRIP‟ statusof motorb. digital temperature controller, indicatores,includingnecessary wiring and accessories as required.

Spare:

d. 1 No. 40 amps TPN MCCB

d. 1 No. 16 amps TPN MPCB

e. Necessary cable alleys, internal wiring, andinterlocking, earthing for all equipment shall alsoincludedNotes :

a. All MCCB/MPCBs shall be of 25 KA breaking capacityand suitable for motor duty application.b. Provision shall be made for providing potential freecontacts to all pumps starters for connection to BAS

c. Provision shall be made to ensure system protectionfrom dry running of the pumpMCC - For Solar water system as described above. Set 1

Total of Solar Hot Water System Works

Interior Works

FLOORING WORKS



172 Providing and fixing of flooring with Premium qualityapproved make of full bodied vitrified floor tiles

(seamless joint) confirming to IS 13006/EN 176Group BIa with tech.specification as Mohs scratchhardness greater than 6,Water Absorption of 0.06%,Modulus of Rupture greater than 27 N/mm, DeepAbrasion resistant less than 204 mm cube, Surfaceflatness, Straightness of sides ± 0.25%, thickness ± 5%of size of approved colour and size & thick as specifiedbelow, set in 20mm thick C.M.1:4 and pointing withapproved make epoxy grout of to matching colour shadeas per Manufacturer's Specification and as directed. Rateshall include wastages, for preparation of base surface,cleaning, acid wash, and finished surface, protection withGypsum / Pop layer over Plastic sheet and removingthe same before handing over,work at all levels and asdirected.Rate shall be inclusive of forming pattern asshown in dwg and wastages etc; as complete in allrespects and complying with relevant standardspecifications and as directed by the Engineer-incharge.

Size of tiles shall be 600mmx600mmx10mm.

Sqm. 8510

173 Providing and fixing of flooring with Premium qualityapproved make of Matt finish, outdoor full bodied

vitrified tiles (seamless joint) confirming to IS 13006/EN176 Group BIa with tech.specification as Mohs scratchhardness greater than 6,Water Absorption of 0.06%,Modulus of Rupture greater than 27 N/mm, DeepAbrasion resistant less than 204 mm cube, Surfaceflatness, Straightness of sides ± 0.25%, thickness ± 5%of size of approved colour and size & thick as specifiedbelow, set in 20mm thick C.M.1:4 and pointing withapproved make epoxy grout of to matching colour shadeas per Manufacturer's Specification and as directed. Rateshall include wastages, for preparation of base surface,cleaning, acid wash, and finished surface, protection withGypsum / Pop layer over Plastic sheet and removingthe same before handing over,work at all levels and asdirected.Rate shall be inclusive of forming pattern asshown in dwg and wastages etc; as complete in allrespects and complying with relevant standardspecifications and as directed by the Engineer-incharge.Size of tile shall be 300x300x10mm size.

Sqm. 1220



174 Providing and fixing of flooring with Premium qualityapproved make of full bodied vitrified floor tiles

(seamless joint) confirming to IS 13006/EN 176 Group BIawith tech.specification as Mohs scratch hardness greaterthan 6,Water Absorption of 0.06%, Modulus of Rupturegreater than 27 N/mm, Deep Abrasion resistant less than204 mm cube, Surface flatness, Straightness of sides ±0.25%, thickness ± 5% of size of approved colour and size& thick as specified, the tile shall be laid with 4mm thickspacer semi glossi / honed finish joints are fillied withapproved make Epoxy grout (office area) and tile set incombination of Laticrete adhesive L 111 and L 73 (cementtiious powder and latex rubberised liquid ) orEquivalent approved make to a thick not less than 6mm(for surface contact of the bottom of the virtified tile)protection with Gypsum / Pop layer over Plastic sheetand removing the same before handing over,work at alllevels & as per approved pattern/design usingirrespective of size and shape, Rate shall include forpreparation of base surface & finishing as per

manufacturer's Specification and as directed.(600x600x10mm)

Sqm. 3000

175 Providing flooring with best quality approved make Anti

Skid Ceramic tiles ranges, sizes as listed below shall8.0mm thick set in CM 1:4, 20mm thick and pointing the joints with Laticrete adhesive L 290 and pointing withLaticrete make Latapoxy SP 100 of approved make as perManufacturer's Specification and as directed. Rate shallinclude for preparation of base surface, and finishing thesurface, cleaning the surface, and protecting and withGypsum / POP layer over Plastic sheet and removing thesame before handing over, work at all levels etc. as

complete in all respects and complying with relevantstandard specifications and as directed by the EngineersIn-charge.. Size of tiles shall be 300mmx300mm.

Sqm. 480

176 Providing flooring with best quality approved colournatural marble slab thick 20mm of size not less than 1200x 900 mm/ 900 x 600mm, machine cut with water (without kerosene ), set in combination of Laticreteadhesive L 111 and L 73 ( cementtiious powder and latexrubberised liquid ) or Equivalent approved make to athick not less than 9mm (for surface contact of the bottomof the marble slab) as per approved pattern/design

drawing using irrespective of size and shape, includingfinishing the joints with Laticrete make UnsandedCementitious grout L 600 series or Rate shall include forpreparation of base surface & finishing the joints withwhite cement slurry, cutting, edge chamfering andpolishing rough, medium, nice and acid wash and tin-oxide polish as per manufacturer's Specification and asdirected.



a Rate shall include for preparation of base surface &finished the surface, protection with gypsum/pop layerover plastic sheet and removing the same before handingover, work at all levels and as complete in all respects andcomplying with relevant standard specifications and asdirected by the Engineers In-charge.. The tolerance inlevel shall be +/-1mm.

Sqm. 1340

177 Providing and laying with best qualityof approved colurItalian marble perlato sicilio 20mm of size not less than1200 x 900 mm/ 900 x 600mm, machine cut with water (without kerosene ), set in combination of Laticreteadhesive L 111 and L 73 ( cementtiious powder and latexrubberised liquid ) or Equivalent approved make to athick not less than 9mm (for surface contact of the bottomof the marble slab) as per approved pattern/designdrawing using irrespective of size and shape, includingfinishing the joints with Laticrete make UnsandedCementitious grout L 600 series or Rate shall include forpreparation of base surface & finishing the joints withwhite cement slurry, cutting, edge chamfering and

polishing rough, medium, nice and acid wash and tin-oxide polish as per manufacturer's Specification and asdirected by the Engineer-incharge.

b Rate shall include for preparation of base surface &finished the surface, protection with gypsum/pop layerover plastic sheet and removing the same before handingover, work at all levels and as complete in all respects andcomplying with relevant standard specifications and asdirected by the Engineers In-charge.. The tolerance inlevel shall be +/-1mm.

Sqm. 345

178 Providing flooring with best quality approved colour

granite slab not less than 18 mm thick of size not less than1200 x 900 mm/ 900 x 600 mm, machine cut with water (without kerosene ) and factory high pre-polished, set incombination of Laticrete adhesive L 111 and L 73 (

cementtiious powder and latex rubberised liquid ) or

Equivalent approved make to a thick not less than 9mm(for surface contact of the bottom of the granite slab) asper approved pattern/design drawing using irrespectiveof size and shape, including finishing the jointswith Laticrete make Unsanded Cementitious grout L 600

series or equivalent and cutting, edge chamfering andpolishing with tin-oxide / high gloss factory polish as permanufacturer's Specification and as directed. Grindingafter laying for level adjusment shall not be permitted.Rate shall include for preparation of base surface &finished the surface, protection with gypsum/pop layerover plastic sheet and removing the same before handingover,work at all levels and as directed.For steps (Raiserand Treads) instead of floor (including edge mouldingwith polishing and non slippery stripes etc;)

Sqm. 580



179 Supplying and fixing 20 mm thick granite of approvedcolur for counter top for wash basin laid in 20 mm thickcement mortar 1:4 over the concrete surface and edgechamfering and providing the hole in the granite forfixing the pillar cock tap etc., complete and as directed bythe Engineer -incharge.

Sqm. 184

180 Providing flooring with best quality jet Black or approvedcolour of leather finish granite slab not less than 18 mmthick of size not less than 1200 x 900 mm/ 900 x 600,machine cut and machine high pre-polished, set in C.M1:4, 20 mm thick topped with white cement slurry (forsurface contact of the bottom of the granite slab) as perapproved pattern/design drawing, including finishingthe joints with white cement slurry, cutting, edgechamfering and polishing rough, medium, nice and acidwash and tin-oxide polish as per manufacturer'sSpecification and as directed. Rate shall include forpreparation of base surface & finished the surface,protection with gypsum/pop layer over plastic sheet andremoving the same before handing over, work at all levels

and as complete in all respects and complying withrelevant standard specifications and as directed by theEngineers-Incharge. The tolerance in level shall be +/-1mm.

Sqm. 212

181 Providing and fixing flooring with cement based pressed

button tile of approved make, thick not not less than 22mm thick of approved colour / pattern of specified shape& size (as per drg), over a bed of CM 1:4, 20mm thickincluding jointed with matching cement slurry includingpreparation of base surface, and finished the surface,cleaning the surface, work at all levels etc.,as complete inall respects and complying with relevant standard

specifications and as directed by the Engineers-Incharge.

Sqm. 74

182 Providing flooring with best quality approvedKotah stone slab not less than 20 mm thick and the sizeof slab in general not less than 1200mm long and widthas per drg. machine cut and machine high pre-polished,set in C.M 1:4, 20 mm thick topped with white cementslurry (for surface contact of the bottom of the Kotah slab)as per approved pattern/design drawing by usingirrespective of size and shape, including finishing the joints with white cement slurry, cutting, edge chamferingand polishing rough, medium, nice and acid wash

and tin-oxide polish as per manufacturer'sSpecification and as complete with all respectscomplying with relevant standard specfication asdirected by the department Engineer-Incharge/Consultant. Rate shall include for preparationof base surface & finished the surface, protection withgypsum/pop layer over plastic sheet and removingthe same before handing over, work at all levels, asdirected.

Sqm. 143



183 Providing flooring with best quality approved Kotah

stone slab not less than 20 mm thick and the size ofslab in general not less than 1200mm long and width asper drg. machine cut and machine high pre-polished, setin C.M 1:4, 20 mm thick topped with white cementslurry (for surface contact of the bottom of the Kotahslab) as per approved pattern/design drawing byusing irrespective of size and shape, including finishingthe joints with white cement slurry, cutting, edgechamfering and polishing rough, medium, nice and acidwash and tin-oxide polish as per manufacturer'sSpecification and as complete with all respectscomplying with relevant standard specfication asdirected by the department Engineer-Incharge/Consultant. Rate shall include for preparationof base surface & finished the surface, protection withgypsum/pop layer over plastic sheet and removingthe same before handing over, work at all levels, asdirected. For steps (Raiser and Treads) instead offloor (including edge moulding with polishing and non

slippery stripes etc;)

Sqm. 1192

184 Providing and laying of laminated wooden flooring butin general it shall be provided with 8mm thick HDFplanks of size 194mmx1286mm with factory tongue andgroove joints, glue fixed and edges finished withnecessary profiles of skirting / reducer as permanufactures specification. Rate shall be inclusive ofproviding 4mm polyethene sheets as under lay on theexisting floor. The tolerance in level shall be +/-1mm.Note: Approved make shall be Tarkett Sommer orequivalent, as completed with all respect and complying

with relevant standard specification as directed by theEngineer-Incharge.

Sqm. 80

185 Supplying and fixing Imported Vinyl flooring with roll

form vinyl tile of approved make & shade 2mm mm thickof standard sizes as per IS –3462 / BS 3261 of

manufacturers specification over the existing floor. Therate shall include all cuttings and wastages, cutting andproviding tile above electrical trunking, cost of allmaterials adhesives of SR-505 FEVICOL of M/s. PIDILITEIndustries Ltd., make etc, including welding of joints.,complete. Only laid area will be measured for payment.Rate quoted shall be for the complete finished work

including all the materials and labour mentioned above.

Sqm. 73

186 Providing, supplying & installing imported Broad loom

carpet / ROLL TYPE of approved make in the specifiedareas as per specifications, patterns/drawing specifiedbelow.

i Face Construction

Construction - Roll Type

Yarn- recyclable Nylon



Gauge - 1/10 to 1/12

Pile stitches per inch : 9 to 12

Pile Height Average : 5mm

Density factor Minimum 25000 to 37500 oz/cubic yard

Over All Thickness : 7 to 8 mm

Fiber System : Nylon

Dye Method - Solution dyed yarnSoil / stain protection - suitable pretreatmentrequired (protect)

ii Backing System

Backing System : Polypropylene

iii Product Testing

Surface Flammability

Flooring radiant panel -Class1

Electrostatic property-3.0 kv or lower

Colour fastness to light-great->_4 after 100 hours

iv Adhesive system

Tackifier applied to the floor meeting low VOC (Volatile

Organic compound) specificationsv Installation Method

Adhesive applied on the floor.

vi Warranties

Minimum 15 year warranty with replacementagainst excessive wear, edge ravel, zippering & backingreiliency loss. Warranty certificate from manufacturer tobe furnished.

vii Product

Size : 3.66m width

viii Cost

Cost to include plastic covering protection after

installation, shampooing before hand over, 2% attic stock,all handling, transportation, wastage, taxes and dutiesthat are applicable etc; complete.

Sqm. 205

187 False Flooring

Providing and fixing Access floor systems of Unitile® or

approved equivalent make all as per followingspecifications confirming to PSA MOB -PF2 PS/SPU orNFPA 262 standards.

System : Access floor system to be installed shall providea maximum finished floor height of upto 600mm from theexisting floor level. The system shall provide for suitablepedestal and under-structure designed to withstand

various static loads and rolling loads subjected to it in anoffice / server / DCS / panel / rack area. The entireAccess floor system shall provide for adequate fireresistance, acoustic barrier and air leakage resistance.



Panels : Access Floor panel of size 600x600 mm shall beall steel welded construction, with an enclosed bottompan of 64 hemispherical cones and top plain sheet whichare fuse welded at 124 locations to form a panel of anoverall depth of 37 mm. The inner empty core of thepanel is injected with a light weight fire retardant, noncombustible cementitious compound at high pressure tofill in all the crevices of the panel and ensures support ofnot less than 85% of the top surface area of the panel. Thepanel after cleaning, degreasing, phosphate by 7 tankprocess is coated with 40 micron epoxy coat and is heatedto achieve maximum adhesion and surface resistance. ThePanels shall be UL listed/ FM approved.

The panel is then laminated with 1.5 mm thick fire

retardant floor grade antistatic laminate/pvc on a semi -automated lamination line to ensure maximum bondingto the steel surface. The edges of the laminated/PVC areprotected with black PVC edge trim 5mm wide on allsides. This edge trim is mechanically locked and sealed in

place to avoid detachment

Pedestals : Pedestal installed to support the panel shall besuitable to achieve a finished floor height of 75 to 600mm.Pedestal design shall confirm speedy assembly andremoval for relocation and maintenance. Pedestal base tobe permanently secured to position on the sub floor.Pedestal assembly shall provide for easy adjustment ofleveling and accurately align panels to ensure lateralrestrain. Pedestals shall support an axial load of 2000 Kgs,without permanent deflection and an ultimate load of3500 Kegs. Pedestal head shall be designed to avoid anyrattle or squeaks.

Pedestal Assembly : Consisting of 100 x 100 x 2mm thickgalvanized epoxy polyester coated MS Base plate die-pressed orbitally riveted to a 21mm O.D. 2.5mm thickepoxy coated MS pipe to engage the pedestal headassembly. The pedestal head assembly consists of anembossed steel plate having 4 holes with ¼ th tapping forfastening and locating of tile ; orbitally riveted to acorresponding threaded stud 16mmdia. (O.D), length100mm which is designed to engage the pedestal baseassembly. The assembly shall provide a range of heightadjustment upto 25mm, with the help of check nuts.

Understructure : Understructure system consists ofstringers of size 570 x 32x 20 x 1.5mm to form a grid of 600x 600mm. These stringers are locked into the pedestalhead and run both ways. The US system shall provideadequate solid, rigid and quiet support for access floorpanels. The US system shall provide a minimum clear,uninterrupted height of 550 mm between the bottom ofthe floor and bottom of the access floor for electricalconduiting and wiring.



Stringers : Stringer system is all steel construction,rectangular channels 30 x 20 x 1.6mm thick with pre-punched counter sunk holes at both ends for securing thestringers onto the pedestal head ensuring maximumlateral stability in all directions. The grid formed by thepedestal and stringer assembly shall receive the floorpanel.Panel Loading: The panel dimensions and performancemust confirm with PSA MOB - PF2 PS/SPU standards fora heavy duty panel and must comply with the,Concentrated Point Load : 450 kgs on a 25 x 25 mm squareon the centre of the panel with a maximum permissibledeflecting of not more than 2.5mm & UniformlyDistributed Load (UDL): 1200 kg/M2 with a maximumpermissible deflection of not more than 2.0mm. Fire

Rating : The Panels shall confirm to Class O & Class 1 FireRatings tested as per BS 476 Part 6 & 7

Rate shall include to produce a test certificate for theabove load of approved laboratory, preparation of

surface, cutting for supply/return Air Grills and forGrommet of required size, wastages, lead & lift, groutingthe system with anchor fastener, removing all debris fromthe premises etc. complete, as directed and for providingclass O Armaflex Nitrile rubber of 15mm thick as a sub

floor insulation with SSR 98 adhesives to the entire areaof existing (Below false flooring) as per manufacturer'sspecification. Rate shall inclusive of providingramp/Steps in false flooring in the entry as shown indrawing.

The height of the jacks shall be 600 mm . Sqm. 375

188 Providing and fixing Unitile® or approved equivalent

makes panel lifter. The panel lifter having special twocup suction panel lifting tool, designed for heavy dutyload carrying capacities with safety lever attachmentwhich requires deliberate manual movement to unlockthe panel.

Nos 2

189 Supplying and fixing of barrier mat of Esplanade Plusfrom GRADUS MATTING. The rate inclusive of necessaryedging strips/mat well frame ect, all as per manufactureslandered specification. Size as per approved drawings.

Sqm. 6

190 Providing and fixing of SS Box section for edge guard tobarrier mat as per approved drawingSize 25x25mm RMT 18



191 Providing and laying 3mm thk self smoothing Epoxy

floor topping over the grano flooring in recreational blockareas.Grinding the surfaces, cleaning the surfacethoroughly & removing laitance completely and thenapplying solvent free primer on the concrete surface andseeding with fine aggregates so as to get a goodmechanical key and allow it dry and then applying andlaying 3mm thick self-smoothing epoxy toppingflowshield SL or approved equivalent make in approvedcolour and allow it dry. Rate shall include chipping,levelling, applying, tool & tackles,electricity, water etc.. asdirected by the Engineer-Incharge.

Sqm. 450

SKIRTING WORKS

192 Providing skirting 100 mm high with full bodied

vitrified floor tiles of approved equivalent make, 10 mmthick set in Laticrete adhesive L290 including pointingwith Latapoxy SP 100 joint filler compound of Laticrete orapproved matching shade and all as per Manufacturer'sSpecification. Rate shall include for chasing of wall for

flushing the tile inline with wall surface, preparation ofbase surface and acid wash at all levels and as perdrawing.

a Vitrified tile – Matt finish. RMT 460

b Vitrified tile – Polished. RMT 11220

193 Providing 100 mm high skirting with best qualityapproved colour marble slab of thickness not less than

18 mm, machine cut and machine high pre-polished set inLaticrete adhesive L 290 to a thick of 4mm uniformly andfinishing the joints with Latapoxy SP 100 of Laticrete orequivalent make, at all levels and all as per drawingdirected. Rate shall include for preparation of surface,

with tin-oxide / high gloss factory polish. Rate also toinclude filleting/ chamfering of the edges along withpartial recessing of the skirting into masonry / gypsumwall

RMT 3820

194 Providing 100 mm high skirting with 2.0 mm thickArmstrong or approved equivalent make quartzreinforced Anti static vinyl over existing cement skirtingincluding preparation of surface and fixing the tile usingFevicol SR998 / Vamicol FC100B adhesive and finishingthe surface neat etc., complete. The rate shall inclusivepreparation of base surface and protection with plasticsheet at all levels etc as complete as directed by theEngineer-incharge.

RMT 200



195 Providing 100 mm high skirting with best qualityapproved Kotah slab of thickness not less than 20 mm,

machine cut and machine high pre-polished set inLaticrete adhesive L 290 to a thick of 4mm uniformly andfinishing the joints with Latapoxy SP 100 of Laticrete orequivalent make, at all levels and all as per drawing . Rateshall include for preparation of surface, with tin-oxide /high gloss factory polish. Rate also to include filleting/chamfering of the edges along with partial recessing ofthe skirting into masonry / gypsum wall etc as completeas directed by the Engineer-incharge.

RMT 4061

196 Providing 100 mm high skirting with best qualityapproved Jet Black granite slab of thickness not less

than 18 mm, machine cut and machine high pre-polishedset in Laticrete adhesive L 290 to a thick of 4mmuniformly and finishing the joints with Latapoxy SP 100of Laticrete or equivalent make, at all levels and all as perdrawing. Rate shall include for preparation of surface,with tin-oxide / high gloss factory polish. Rate also to

include filleting/ chamfering of the edges along withpartial recessing of the skirting into masonry / gypsumwall etc as complete as directed by the Engineer-incharge.

RMT 885

197 Providing and fixing 100 mm high skirting made from 12mm thick BWP board finished with 1.5mm laminate ofapproved shade & colour, bottom and top edge coveredwith 4mm thick polished teak wood lipping as perarchitectural drawing with 4 mm grooves at top enamelpainted of approved colour. The ply being grouted to theGI channel etc as complete as directed by the Engineer-incharge.

RMT 100

198 Providing and fixing of aluminiumskirting (Gradus/ALLOY or approved equivalent make)100mm high and 1mm thick of aluminium profile ofapproved colour fixed at wall/partition etc as complete asdirected by the Engineer-incharge.

RMT 2000

WALL DADO

199 Providing dadoing with machine cut and machine highpre-polished best quality approved colour granite tile of

thickness not less than 10mm of size

600x600mm/600x300mm, set in cement mortar 1:3,pointing the joints with approved Tile‟ joint filler grout

compound matching to the granite color and as directed.Rate shall include for preparation of base surface, such ashacking, cleaning, wastages, smooth joint, necessarycorner/edge guards of matching color, cleaning and acidwash etc. etc as complete as directed by the Engineer-incharge.( Lift Lobby, Corridor )

Sqm. 1604



200 Providing Dadoing with best quality Ceramic tile ofapproved make and size of 300x450mm set in cementmortar 1:3, pointing the joints with approved Tile‟ joint

filler grout compound as per Manufacturer's Specificationand as directed. Rate shall include for preparation of basesurface, such as hacking, cleaning and acid wash completeall as directed. Rate shall include wastages, smooth joint,necessary corner/edge guards of matching color, cleaningand acid wash etc. etc as complete as directed by theEngineer-incharge. (toilets)

Sqm. 3929

201 Providing and fixing Natural Marble Cladding slab ofthickness not less than 25 mm size of approved colour &shade of size not less than 900x600 / 1200x600 mm orapproved size, using dry fixing method. Each marble slabis to be individually supported using 4 Nos. of stainlesssteel cramps, screws & bolts are 316 'L' grade two each attop and bottom. Each SS cramp will be of size 75 x 50 x 5mm thickness as shown in drawing and as directed.Each SS cramp will be fixed to the wall using two

numbers of MS oxidized non-corrosive expansion anchorfasteners of size 10 mm head, 6 mm dia. and 100 mmlength for masonry work , 10 mm head, 6 mm dia. and 50mm length for RCC areas. Each marble slab will have twoSS cramps at the bottom with the lipping of 12 mm heightembedded in the groove cut in the marble, the groovedepth being 20 mm and width being 6 mm etc ascomplete as directed by the Engineer-incharge.

Each slab will also have similar 2 cramps at the top,balance gaps in the grooves will be filled with metal paste.There will be no gaps seen between the marble slabs in

elevation. Any corner or junction slab which may be ofsmaller size should also be supported similarly. It has tobe ensured that the slabs are perfectly vertical and inplumb. The gaps between the marble slabs is to be filledwith water proof cement paste GRIPFIX (CICO, powderand liquid mix) as per manufacturer specifications, usingmatching colour pigments depending on the slabs. Thegaps on the top and sides of the marble fixing will have tobe closed using coping slabs to prevent water fromcoming in. Rate shall include for fabrication and fixing ofSS cramps, anchor fasteners, supplying and fixing „M-

seal‟, water proofing compound, groove cutting in granite

and double scaffolding to the required heights, wastagesetc as complete as directed by the Engineer-incharge. for

lift lobby.

Sqm. 420



202 Providing and fixing in wall dado with best qualityapproved make Screen printed ceramic tiles ranges, sizesas listed below shall 6.0mm thick with matching bordersand set in CM 1:4, 15 mm thick and pointing the jointswith Laticrete adhesive L 290 and pointing with Laticretemake Latapoxy SP 100 of approved make as perManufacturer's Specification and as directed. Rate shallinclude for preparation of base surface, and finishing thesurface, cleaning the surface, and work at all levels etc. ascomplete in all respects and complying with relevantstandard specifications. Rate shall include wastages,smooth joint, necessary corner/edge guards of matchingcolor, cleaning and acid washetc as complete as directedby the Engineer-incharge.

Size of tiles shall be 300mmx300mm (Kitchen, utility etc..) Sqm. 340

Total of Flooring Works

PAINTING WORKS

203 Providing Acrylic emulsion paint - Painting with acrylic

emulsion paint of Low VOC paint ( complying with allgreen rating systems) and of approved make and colouror equivalent make two or more coats as permanufacturers specifications and as directed. The rateshall be inclusive of necessary scaffolding or staging etc.ascomplete with all respects complying with relevantstandard specification, as directed by the Engineer-Incharge.

Sqm. 75746

204 Providing and applying of "Royal Play" paint from Asian

or approved equivalent make. to walls of approvedcolour over a coat of primer as per manufacturespecification. The rate shall be including preparation ofsurface by thorough cleaning and as per manufacturer‟s

specification fully to give an even shade s directed by theEngineer-Incharge.

Sqm. 50

205 Providing & applying POP punning plaster 6-10 mmthick over exposed wall surface including scaffolding etc.complete. Rate to include for making the wall with plumbline and get smooth surface to receive the paint.( allplaster surface) and also include cost of material, labour,unloading and shifting of material,water etc..as completeand as directed by Engineer-Incharge.

Sqm. 75746

206 Providing two coats of synthetic ready mixed Enamel

paint to wooden / steel work of approved colour over acoat of respective primer includingpreparation of surface by through cleaning as permanufacture's specification fully to give an even shadeetc..as complete and as directed by Engineerin-charge.

Sqm. 1855

Total of Painting Works

FALSE CEILING WORKS



207 Providing & Fixing of Eco Perforated metal Lay in

ceilings System (Fameline/Armstrong or approvedequivalent make) consisting of 600x600mm Lay in tilesmade of Aluminium Alloy 1100 with powdercoated(polyester base) to 60 microns in 0.7 mm thicknessin approved colour with standard perforation of 2.6mmdia & open area of 17% and Freudenberg Soundtexacoustical fleece glued to the back of the tile to be laid ongrid systems with 15mm wide T - section flanges colourwhite having rotary stitching on the Main Runner, 1200mm & 600 mm Cross Tees. The T Sections have aGalvanizing of 120 grams per M2 & passed through 500hrs of Salt test. The tiles should have Humidity Resistance(RH) of 100%, NRC of 0.70, Fire Performance A2-s1.d0 inmodule size of 600 X 600 mm, suitable for Green Buildingapplication, with Recycled content of 50%. The Tile &Grid system used together should carry a 15 yearwarrantee.

INSTALLATION: To comprise main runner spaced at

1200mm centers securely fixed to the structural suffix at1200mm maximum centre & not more than 150mm fromspliced joints. The First/Last suspension system at theend of each main runner should not be greater than600mm from the adjacent wall. 1800mm long cross tees tobe interlocked between main runners at 300mm centre toform 1800 x 300 mm module. Cut cross tees longer than600mm require independent support. Perimeter trim to bewall angles, secured to walls at 450 mm maximumcenters. The rate shall be inclusive of making openings forlight fittings, grills, diffusers, cutouts, wastage and

necessary hardware etc. as complete in all respectscomplying with relevant standard specifications andas directed by the Engineer-in-charge.(hall )

a For the above specification for Grid system Sqm. 2434

b For the above specification for board (measurement onlylaid area)

Sqm. 2434



208 Providing and fixing in true horizontal level false ceiling

of 15mm T-section grid system Manufactured by M/s.Saint Gobain/Armstrong/USG/Daiken or approvedequivalent make using hot dipped galvanized steelsection, exposed surface chemically cleaned capping pre-finished in baked polyester paint, wall angle of size 3000 x19 x 19mm used in the periphery of the ceiling fixed to thewall partition / R.C. Column / band walls with the helpof screws at 600 mm C/C. Main runner spaced at a1200mm C/C suspended by using 2mm dia G.I. wirehanger securely fixed to the structural soffit of RC slab byusing 6mm anchor fastener at every 1200mm (max) and1200mm long cross tee to be interlocked between in Mainrunner at 600mm C/C (max) to form a grid of 1200 x600mm. 600mm long cross tee fixed in between 1200mmlong cross tee for forming a grid of 600 x 600mm.

Laying of FINE FISSURED (MICRO LOOK) tiles shouldhave Humidity Resistance (RH) of 99%, NRC 0.55, Light

Reflectance >85%, Thermal Conductivity k = 0.052- 0.057w/m K, Colour White, Fire Performance Class 0/ Class 1(BS476 Part 6&7) in module size of 600 X 600 X 16 mmwith Bio Block coating on the face of the tile, suitable forGreen Building application, with Recycled content of 63%.as complete in all respects complying with relevantstandard specifications and as directed by the Engineer-incharge.

a For the above specification for Grid system Sqm. 1665

b For the above specification for Fine fissured board(measurement only laid area)

Sqm. 1665

209 Providing and fixing mositure resistant seamless

gypsum ceiling with Gyproc MR or approved equivalentmake of 12.5 mm thick, fixed to the underside of thesuspended grid formed of GI perimeter channel of size 20x 28 x 30 mm fixed along the wall by using wood screwsand metal expansion rawl plugs. The GI intermediatechannel of size 15 x 45 x 15 x 0.90 mm shall be fixed to thesuspended strap hanger / GI ceiling angle at intervals notmore than 1220 mm. The suspended GI ceiling angle /.Strap hanger is to be connected with GI soffit cleat of size37 x 27 x 25 x 1.6 mm and it should be fixed on the roofslab / beam, by using metal expansion fasteners (wt.Type) of 12.5 mm dia. to a length of 35 mm with 6 mm

dia. bolt / screw at top ends.



The GI ceiling section of size 80 x 26 x 0.5 mm (MF 5) is tobe provided across the intermediate channel at intervalsnot more than 457 mm centres at bottom and the sameshall be fixed by GI connection clips 2.64 mm dia. at theintersection points. The ends of ceiling section channel byadopting an overlap length of minimum 150 mm,connected with intermediate channel shall be fixed toperimeter channel in insertion. The gypboard shall befixed to the under side of the suspended grid by using 25mm long dry wall screws. The joints shall be finished with joint paper tape by using jointing compound of SaintGobain Gyproc or approved equivalent make andapplying over it 3 layers of the filler compound to providea smooth surface. The ceiling surface shall be painted withthree coats of approved first quality acrylic emulsion overa coat of primer etc. complete. The rate shall includemaking cutouts for tube lights, spot lights, duct doors, forspecified size, grills etc. for which no extra will be paidseparately.

Rate shall include providing additional trimming aroundcutouts for light fittings etc. and grills also for providingadditional supports from ceiling where main / crossmembers are cut for light fittings etc. Rate shall includevertical as well as horizontal surfaces as per detaileddrawing. Actual “seen” surface of horizontal and verticalwill be measured and paid for, as complete in all respectscomplying with relevant standard specifications and asdirected by the Engineer-in-charge.

Sqm. 1917

Total of False Ceiling Works

PARTITIONS

210 Providing and fixing of Partition total four layers of

GYPROC FIBRE CEMENT BOARD or approvedequivalent, each layer 12mm thick (in staggered pattern)is screw fixed with drywall screws(zinc chromium plated,self drilling ) of 25mm/35mm at 300mm centres twolayers on each side of 70mm Rondo™/Gypsteel ultra GI

C-stud {0.5mm thick having one flange of 34mm andanother flange of 36mm) placed at 610mm centre to centrein 72mm Rondo™/Gypsteel ultra GI floor Channel (0.55

mm thick have equal flanges of 32mm) which is anchoredto the floor & true ceiling using anchor fasteners. Finallysquare and tapered edges of the boards are to be jointedand finished so as to have a flush look which includes

filling and finishing with Jointing compound, Joint Papertape.



The additional supports shall be provided to the verticalstud and RCC slab above the false ceiling at top with 'Y'type supports. Air gap between the plasterboards is linedwith 50mm rock wool of density 48 Kg/m3 of approvedmake shall be placed in the cavity rock wool rapped with40GSM fiber glass tissue. The contractor must ensure thatthe wool is wire-braced to prevent it from „lumping down‟

over a period of time. Fixing of channels shall also toprovide suitable for attachment of fixtures to thepartitions and the perimeter opening should be trimmedwith studs packed with best quality treated timber frameto a required size and shape with 2 coats of fire proofpaint over a coat of anti-termite treatment / anti-corrosiveprimer to receive screws / anchor fasteners to fix Joineryframe in position etc. as per drawing as complete in allrespects complying with relevant standard

specifications and as directed by the Engineer-in-charge.

a rate shall be inclusive of 12mm thick BWR ply boxing forfixing Switches, sockets, Backup box etc on the partition toa required size and shape.(all lab partition)

Sqm. 2710

b Specification same as above but providing two layers ofboard at one side of the stud for wall paneling/columnpaneling

Sqm. 375

211 Extra rate for over the above, for providing Resin bondedrock wool 50mm to (acoustic insulation material) densityof 48kg/cum in solid partition to make it as acousticproof.

Sqm. 2160

212 Providing and fixing of 1.0mm thick laminate ofapproved color and shade with grooves and lines and in

patterns drawing on specified area as instructed byEngineer-Incharge. The cost of necessary hardware's,adhesives, wastages etc; as required for complete theworks. Actual visible surfaces only will be measured andpaid.

Sqm. 950

213 Providing and fixing of 3.5mm thick veneer of approvedcolor and shade with grooves and lines and in patternsdrawing on specified area as instructed by Engineer-Incharge, exposed surfaces of veneer shall be finishedwith melamine polish of required level. The cost ofnecessary hardware's, adhesives, wastages etc; asrequired for complete the works. Actual visible surfacesonly will be measured and paid. Finishes shall made atFactory only installation at site(portal and DH cabin)

Sqm. 810



214 Providing and Fixing of 12.5mm Gypboard and the jointsbetween the gyp-boards are finished flush and even with jointing compound and paper tape and the surface shallbe painted with 3 coats of acrylic emulsion paint ofapproved make and shade over a coat of primer suitablefor gyp-board after E-Mix / Pop / Gypsum putty and allas per manufacturer‟s specification etc complete and all as

directed. Rate shall include for providing all hardware's,etc.complete as per drawing as directed..

Sqm. 5

215 Providing and fixing toughened glass panel to thespecified thickness as given in below in the solid partition(laminated/Veneer/ calcium silicate/Gypsum board).The frame work in the the glass panel circumference shallbe fixed with 75mmx19mm size first class teak woodframe and fixing the toughened glass at the centre of teakwood frame using first class teak wood beadings to shapeand size as per drawing. The exposed teak wood surfacesshall be finished with melamine polish. The rate to beinclude the cost of necessary hardware's, adhesives,

wastage etc; as required for complete the works. Actualseen glass surface area will be measured and paid.

a Single layer 8mm thick toughened clear glass Sqm. 5

b 6mm thick lacquered glass of approved colour and SaintGobain or equivalent make

Sqm. 5

216 Providing and fixing of 6mm thick lacquered glass ofapproved colour and Saint Gobain or equivalent makeover the existing partition, paneling or wall surfaces asper drawing as directed. The rate shall be inclusive ofnecessary SS Stud/Double side 3M sticker, hardware andwastage etc; complete.

Sqm. 15

217 Providing and fixing Partition above the false ceiling

level using total two layers of GYPROC FIBRE CEMENT

BOARD or approved equivalent, each layer 12mm thick(in staggered pattern) is screw fixed with drywall screwsof 25mm / 35mm at 300mm centres one layers on eachside of 70mm Rondo™/Gypsteel ultra GI C-stud {0.5mm

thick having one flange of 34mm and another flange of36mm) placed at 610mm centre to centre in 72 mmRondo™/Gypsteel Ultra GI floor Channel (0.55 mm thick

have equal flanges of 32mm) which is anchored to thepartition bottom & true ceiling using an anchor fasteners.Finally square and tapered edges of the boards are to be

jointed and finished so as to have a flush look whichincludes filling and finishing with Jointing compound, Joint Paper tape as per manufacturers specification, ascomplete in all respects complying with relevant standardspecifications and as directed by the Engineer-in-charge.

Sqm. 630



218 Providing and fixing of single layer 9mm thick calciumsilicate board in the existing aluminium/GI partitionsexcept the cost of aluminium/GI frame work. The jointsare to be finished with jointing compound as permanufacturers specification. The boards shall be fixedwith counter sunk stainless steel / fully threaded selftapping screws of suitable dia and length at every 300 mmc/c. The rate shall be inclusive of necessary scaffolding,hardware etc.complete. (above false ceiling solid

artition)

Sqm. 950

219 Straight Glazed Partition-(Type "A" partition) Slim linepartition of JEB/Alloy Make or equivalent approvedmake: Supply and installation of full height straight glasspartition 12mm thick toughened glass and proprietaryanodized aluminium sections of the SLIM LINE series of40x18mm size as per drawing as directed. The sectionsshall be matt natural anodized and Alloy sectionscombination of 40.02 , 40.03, 40.05 & 40.06 and 40.07would be used on all four sides as per specifications andshall be inclusive of all accessories. for FFL to the bottom

of false ceiling height.

Sqm. 1200

220 Wide line Section at around Door as per drawing, JEB/ALLOY Make or equivalent approved make at threesides of door opening : Supply and installation of wideline door frames using Alloy sections combination 100.02 ,100.03, 100.05 & 100.06 and 100.07 would be used at sidesand top etc. as per specifications and shall be inclusive ofall accessories.. The section shall be matt natural anodizedas per manufacturer's specification. The rate shall beinclusive of necessary additional plate provision for fixingof card reader and access control switch etc.

RMT 10

221 Supplying and fixing Fully openable Patch Fitting

partition and door of ' DORMA' "PT" range Fittings to geta clear height with top & Side Fixed panels as per drawingas directed. In general, the openable door cum Fixedpanel consists of sliding channel with all fitting andCorner Fittings PT90/91, Standard Spindle US10, cornerlock at bottom and US20 with GK50, Euro profile cylinderwith 4keys, lock keeper plate, Pull handle(TGDI35025) SSSatin Finish and 12mm thick clear toughened glass as perdesign and all confirming to manufacturers specification.SS fixtures shall conform Grade SS 304 to BS 7352.

Rate shall include for providing Glass Fin to support thePatch Fitting Door, transport charges, handling, loadingand unloading, Installation, protecting the module andglass till handing over, testing, commissioning allnecessary hardware's, Structural supports if any, etc.complete and all as per manufacturers specifications asdirected.

a Rate for partition only Sqm. 5

b Rate for single/double leaf doors only. Sqm. 10



222 Glass Etching: Fixing to glass panels using 3M filmstickers as per required pattern drawing and shape and asdirected by the Engineer-Incharge.

Sqm. 403

223 Providing and fixing of 2hr fire rated partition total fourlayers of GYPROC FIRELINE BOARD or approvedequivalent, each layer 15mm thick (in staggered pattern)is screw fixed with drywall screws of 25mm/35mm at300mm centres two layers on each side of 70mm GypsteelUltra / Rondo™ GI C-stud {0.50mm thick having one

flange of 33.5mm and another flange of 35mm) placed at610mm centre to centre in 72mm Gypsteel Ultra /Rondo™ GI floor Channel (0.55 mm thick have equal

flanges of 32mm) which is anchored to the floor & trueceiling using M6 x 40 anchor fasteners. Finally square andtapered edges of the boards are to be jointed and finishedso as to have a flush look which includes filling andfinishing with Jointing compound, Joint Paper tape.

The additional supports shall be provided to the verticalstud and RCC slab above the false ceiling at top with 'Y'

type supports. Air gap between the plasterboards is linedwith 50mm rock wool of density 64 Kg/m3 of approvedmake shall be placed in the cavity rock wool rapped with40GSM fiber glass tissue. The contractor must ensure thatthe wool is wire-braced to prevent it from „lumping down‟

over a period of time. Fixing of channels shall also toprovide suitable for attachment of fixtures to thepartitions and the perimeter opening should be trimmedwith studs packed with best quality treated timber frameto a required size and shape with 2 coats of fire proofpaint over a coat of anti-termite treatment / anti-corrosiveprimer to receive screws / anchor fasteners to fix Joineryframe in position etc. complete as per drawing as

complete in all respects complying with relevant standardspecifications and as directed by the Engineer-in-charge.

Rate shall be inclusive of 12mm thick BWR ply boxing forfixing Switches, sockets, Backup box etc on the partition toa required size and shape.(all lab partition)

Sqm. 1450



224 Providing and fixing of fully glazed steel fire ratedpartition and door with 120 minutes of integrity (E=120)fabricated with 1.6 mm thick galvanized steel sheet. Thedoor frames are manufactured from 1.6 mm galvanizedsteel sheet pressed to form a profile of 35 mm x 60 mmonthe vertical sides and 50 x 60 mm on the horizontalside. The door shutter would have a top rail and side rail60 mm x 60 mm and a bottomrail of 110 mm x 60 mm. Theoverall door opening is 1800 mm x 2100+fixed1800x1700mm. The test is conducted in CBRI, Roorkee asper BS 476 Part 22. The glass should be SGGCFDL 11mmclear 120 min rated ( E120) Non Wired Toughened glasswith a light transmission of 89% and a sound reduction of32 db. The glass should be class 1C1 category of ImpactResistance as per EN 12600. The glass should be held in itsplace with the help of 2 mm GI beading and a specialceramic tape with cross section of 5 x 20 mm..

The shutters should be fixed to the frame using 4nos of

Dorma SS Ball Bearing Hinges of size 100 mm x 75 mmand 3 mm thickness. Beading should be attached using 4mm x 35 mm SS screws at a distance of 75 mm from theedges and 150 mm c/c henceforth. The door should befitted with Dorma Mortise Sash lock 952F and door closerTS 68 of Dorma make or equivalent. The inactive leafshould be fixed to the frame using 1200mm long Dormatower bolt no 9114306 or equivalent. (SAINT GOBAIN11mm CONTRA FLAME or approved equivalent make)

a For partition only(UPS and server) Sqm. 40

b For single/double leaf doors only(lobby) Sqm. 19

225 GUIDE SPECIFICATIONS FOR OPTRA ACOUSTICAL

WALL PANELLING:Providing and supplyingArmstrong „Optra Acoustical Wall Panelling‟ or approved

equivalent make with square edges made of fibre glasssubstrate 25mm thick and wrapped on the front side withan acoustically transparent and fire-resistant fabric withan option of colours as per the choice of the Engineer-Incharge/Consultant of size 2100x600 or 600x600 mmproviding a minimum sound absorption level of 0.90 NRCto be affixed to wall using Wall panel impalers suppliedby M/s Armstrong Industries India Pvt. Ltd andconstruction adhesives as per the instructions laid downby the manufacturer.



INSTALLATION: Armstrong or approved equivalentwall panel impalers of adequate quantity as specified bythe manufacturer shall be fixed to the wall surface usingself tapping screws. Silica based construction adhesiveshall be dabbed on to the projecting elements (spikes) ofthe impalers. Armstrong Optra wall panels shall bepierced through the spikes of the impalers ensuring theline and level of the panels are maintained. The rate shallbe inclusive of wastage, hardware and necessarybackings etc.

Sqm. 214

226 GUIDE SPECIFICATIONS FOR ARMSTRONG OR

APPROVED EQUIVALENT MAKE CHANNELED

WOODWORKS WALL PANELLING OF SIZE:

128X2440X16MM Providing and Fixing ArmstrongChanneled Woodworks perforated panels of width128mm, thickness of 16mm and length 2440 mm or asrequired by the Engineer-Incharge/Consultant, made of ahigh density particle board substrate with a laminatedfacing as per the approved shade/ species & finish and a

melamine balancing layer on the reverse side. The boardsshall have a special perforation pattern where the visiblesurface has a (“Helmholtz” fluted perforation of 2mm

width and 14mm of visible panel / 4mm width and 28mmvisible panel) each. The panels shall provide a minimumsag resistance of RH90 and a fire rating class of 1 as perPart 7 of BS 476. The edges of the panels shall be “tongue-

and-grooved” to receive special clips for installation. The

back of the perforated panel shall have sound absorbingnon-woven acoustical fleece. The panels shall be mountedon special aluminium splines using clips provided byArmstrong or approved equivalent make and approvedby the Engineer-in-Charge



INSTALLATION:Install wooden battens (provided byothers) of section 50mmx50mm or as approved by theEngineer-Incharge/Consultant on the solid wallhorizontally using screws and plugs at spacing of 600mmcentre-to-centre. Screw the aluminium extruded keel forchannelled woodworks (GTPT001) over the lowest andsecond wooden batten at an on-center distance of 600mm.Install the first set of wooden panels by inserting the clipsfor border channelled woodworks (GTPT002) and insertthe groove of the panel into the projecting flange of thealuminium clip. Continue installing rows of panels byinserting the tongue into the groove of the earlier insertedpanel and progressively installing clips for insidechannelled woodworks (GTPT003) into the next keel tillthe actual height is achieved. Use clips for borderchannelled woodworks (GTPT002) to finish off theinstallation. Finish off the edges using wooden mouldingof matching colour. The rate shall be inclusive of wastage,hardware and necessary backing etc.

Sqm. 232

Total of Partition Works

Joinery

227 72 Providing and fixing of well seasoned teak wood door

frame approved size and as per drawing detail. Allexposed wooden surfaces are duly polished withmelamine polish of required level. The rate shall beinclusive of making necessary design as per drawing, inthe frame and necessary hold fastener and hardware ect,.The rate shall be inclusive of supply and fixing of 6 nosMS flat iron holdfast for each door of size 40mmx3mmand 40CM long fixing with CC 1:2:4 and 75mm long10mm dia anchor fastener to RCC location where everrequired. Finishes shall made at Factory only installationat site

a Scantling shall be up to 2000mm length CUM 2

b Scantling shall be above 2000mm and below 3000mm CUM 7

228 74 Providing and fixing of 35mm thk.Teak wood panelled

shutter with door frame of approved size and all as perdrawing. All the wooden surfaces are duly polished withmellamine. The rate shall be inclusive of necessary anchorfastener and excluding hardwares, as directed byEngineer-Incharge/Consultant.

Sqm. 139

229 74 Providing and fixing of factory finished solid woodmahogani door jamb of size as mentioned below (full

wall thick) with necessary door stoper(40x22mm),

architrave(40x15mm) or approved size and all as perdrawing detail. All the wooden surfaces are duly polishedwith PU finish of required level. The rate shall beinclusive of making necessary design as per drawing, inthe frame and necessary hilti fastener and hardware etc,.Finishes shall made at Factory only installation at site.



i size of the door frame 230x37mm with two side architrave RMT 647

ii size of the door frame 230x37mm with one side architrave RMT 380

iii size of the door frame 115x37mm with two side architrave RMT 3075

iv size of the door frame 115x37mm with one side architrave RMT 35

230 74 Providing and fixing 35mm thick flush door shutters ofsolid core block board type bonded with phenolformaldehyde synthetic resin thermo pressed with 8mmthick teak wood external edge lipping finished withmelamine polish of approved make, colour & pattern asper drawing. The construction procedure of the shuttershould be as per IS:2202.The size of block, shall perfectlycorrespond to the maximum size of lock, covered inIS:2209. All the four edges of the door shutter shall besquare. The shutter shall be free from twist or warp in itsplane and of required size etc. The rate shall exclusive ofhinges and other hardwares; complete as directed.

a specification same as above but the finishing of doorshutters on both sides with 1.0mm thick laminate ofapproved color pattern.

Sqm. 259

b specification same as above but the finishing of doorshutters on both sides with 3.5mm thick veneer ofapproved color and finishing with melamine polish.etc.complete, directed by the Engineer -incharge The basiccost of veneer. The rate should be quoted for single sidearea of the door shutter.

Sqm. 1059

231 Providing and fixing in position first quality teak wood

beading / architrave of finished size as given below,made to shape and pattern approved with necessary pins,

nails, screws, bolts using teakwood conforming tospecification. Rate shall include two coats of Duco Paintover a coat of wood primer etc. as directed.

Size : 25 x 12 mm RMT 3970

232 2hr. Fire rated hollow metal doors - Painted

Providing and fixing of Hollow metal fire rated doors atall levels from ISO 9001-2000 certified Manufacturer. Firedoor should be as per IS 3614 part-1 & part-2 and BS 476part 2 or EN 1634. Recommended fire door shall be testedand certified by a third party evaluation program fromapproved international agency like CERTIFIER and

labeled. Where third party evaluation is not required firedoors should be tested at CBRI or ARAI for maximumrating of 2hrs both with vision panel and without visionpanel. Pressed Galvanized steel Single /Double leaf doorof approved make shakti met-dor or approved equivalentwhich consists of frame, shutter, infill and finish asdetailed below and conforming to IS 277.



Door frame shall be double rebate profile of size 143 x 57mm made out of 1.60mm (16gauge) thick galvanized steelsheet. Frames shall be Mitered and field assembled withself tabs. All provision should be mortised, drilled andtapped for receiving appropriate hardware. Rubber doorsilencers should be provided on the striking jamb. Framesshould be provided with back plate bracket and anchorfasteners for installation on a finished plastered masonrywall opening. Once frame installed should be groutedwith cement & sand slurry necessary for fire doorson the clear masonry opening.

Door leaf shall be 46mm thick fully flush double skin doorwith or without vision lite. Door leaf shall bemanufactured from 1.2mm (18guage) thick galvanizedsteel sheet. The internal construction of the door shouldbe rigid reinforcement pads for receiving appropriatehardware. The infill material shall be resin bondedhoneycomb core. All doors shall be factory prepped forreceiving appropriate hardware and provided with

necessary reinforcement for hinges, locks, and doorclosers. The edges should be interlocked with a bendingradius of 1.4mm. For pair of doors astragals has to beprovided on the meeting stile for both active and inactiveleaf. Vision lite wherever applicable should be of size200x300mm provided as per manufacturersrecommendation with a beading and screws from inside.The glass should be 6mm clear borosilicate fire rated glassof relevant rating of the door.

All doors and frames shall be finished with etched primercoating, stove zinc phosphate primer and thermosettingpolyurethane aliphatic grade paint of approved RAL

colour. The door leaf and frame shall have passedminimum 250 hours of salt spray test. Rate should includesupply and installation of door and hardware size asmentioned below

a 2Hrs Fire Rated Door Single leaf of size : 600x1500mmwithout vision panel (shaft door)

Sqm. 255

b 2Hrs Fire Rated Door Single leaf of size : 900x2100mmwith vision panel with Self adhesive sponge seal forframes 188S

Sqm. 27

c 2Hrs Fire Rated Door Single leaf of size : 1000x2100mmwith vision panel with Self adhesive sponge seal forframes 188S,

Sqm. 206

d 2Hrs Fire Rated Door Single leaf of size : 1200x2100mm

with vision panel with Self adhesive sponge seal forframes 188S,

Sqm. 30

e 2Hrs Fire Rated Door Double leaf of size : 1500x2100mmwith vision panel with Self adhesive sponge seal forframes 188S.

Sqm. 28

233 Providing and fixing of hardware set of DORMA or

approved equivalent make for the below said item as

listed below.



a Dorma BB 4330- 2 Ball bearing butt hinges size 4" x 3" x3mm in SS 304 for Flush Doors

Nos 2403

b Dorma BB 4330- 2 Ball bearing butt hinges size 4" x 3" x3mm in SS 304 for Fire Doors

Nos 1202

c Push Plate Dorma 9160010 of size 350 X 100 mm x 1.2mmin SS 316 grade

Nos 10

d Dorma H type TGDI 350 x 25 in SS 304 Nos 255

e Dorma D type Handle 150 x 19mm in SS 304 for shaftdoors

Nos 271

f Dorma Flush Pull Sliding door rectangular Nos 4

g Dorma Mortise dead lock 278 with Europrofile Cylinder60mm Length Type 2 (one side key other side thumb turn)with 4 level Master Key

Nos 211

h Dorma Mortise dead lock 278 with Europrofile Cylinder60mm Length Type 1 (both side key) with 4 level MasterKey

Nos 12

i Dorma TH 123 Type 2 Lever Handle with Mortise sashlock as per DIN 18251-1, class 3 & Europrofile Cylinder60mm Length one side key other side thumb turn with 4level Master Key

Nos 48

j One point panic device PHA 2001 - PHA 2102 PHA 2105L = 1300mm, External Trim PHT 3905 preferred for EuroProfile Cylinder, EP Half Cyl 3010, 5 Pin one side keywith 4 level Master Key

Nos 96

k SL - 400- Sliding Door Lock Nos 4

l Dorma Mortice shaft dead bolt 57 mm backset as per DIN18251-1 Class 3 with Alan Key

Nos 263

m Dorma TS 92 cam action door closer Nos 190

n Concealed flush bolt Dorma 3100 Nos 1

o Dorma Flush Bolt Nos 743

p Door stopper Dorma-3108 Nos 46

q Dorma Door Stopper for Residence Nos 597

r Patch Fittings from Dorma Bottom Patch - PT 10, FloorSpring - BTS 75 V, Top Patch - PT 20, Top Pivot - PT 24 Nos 158

s Patch Fittings from Dorma Bottom Patch - PT 10, FloorSpring - BTS 80 V, Top Patch - PT 20, Top Pivot - PT 24

Nos 37

t Dorma SLM 120 Sliding door system for Flush door, 2 MtsLength, SLM 120 Accessories- 01 set , SLM Track - 2 Mts -01 set

Nos 4

234 Providing hardware set of YALE / LOCKWOOD or

approved equivalent make for the below said item as

listed below.

a YALE - M8773 D3 - ENTRANCE HANDLE SET EleganceSeries D Handleset Design with 2 keys and 3 level MasterKey

Nos 4

b YALE - 6688 SC - ENTRANCE HANDLE SET BALISERIES with 2 keys and 3 level Master Key

Nos 97

c YALE - CA5137 ENTRANCE KNOB LOCK with 2 keysand 3 level Master Key

Nos 533

d YALE - CA5132 PRIVACY LATCH with 2 keys and 3level Master Key

Nos 146

e LOCKWOOD - DSS 03- 180 Degree Door Viewer Nos 102



f LOCKWOOD - DSS 02- Security Door Guard Nos 102

Total of Joinery Works

MISCELLANEOUS

235 Providing and fixing Reception table made to shape andpattern identical as per Drawing. and to a height of twolevels 1050 mm/ 750 mm , but in general it shall be madeof 18mm thick BWR plywood as table top, sides, front and

rear side with adequate supports as directed in bothhorizontal and vertical directions. Providing drawers unitwith three drawer as per drawing, and side storage withopenable postformed edge shutters and one intermediateshelf at one sides of the table. All the front, side‟s surfacesfinished with combination of corian material of approvedcolor and 6mm thick milky white glass with inside lightprovision as per drawing detail, Table top at 750mm with25mm thick exterior grade particle board with postformedlaminate (campagne shade from Merino) and at 1050mmht top shall be finished with corian material of approvedcolor.

Rate shall be inclusive of providing edge molding ofapproved shape, making cut open in the table as perdrawing detail, storage shutter and drawer are made with18mm thick BWR ply finished with 1.5mm thick laminateof approved colour and other recessed surfaces arefinished with 1mm thick laminate. Rate shall include fornecessary wastages, hardware's(Hettich) like slidingrunners, auto closing hinges, locking facility with onemaster key for Two drawers and storage, aralditeadhesive for fixing corian etc. Rate to include forproviding teakwood lipping, teak wood foot rest dulyfinished with melamine polish etc. All factory finished asper drawing.

RMT 12

236 Providing and fixing soft board panel of specified sizeshaving 12 mm thick soft board covered with felt fabric ofapproved make and shade of premium quality The boardshall have beech wood beading, lipping all-round. Theboard shall be fixed on prepared surface with necessaryhardware fittings etc. complete. All concealed woodworks shall have sealer polish as directed. Rate quotedshall be for the complete finished work including all thematerials and labour mentioned above.

Sqm. 165

237 Providing and fixing Pelmet made to shape and sizes as

given in below, but in general it shall be made out of18mm thick BWR plywood and lined with 1.5mm thicklamination of approved colour as directed. The rate shallbe inclusive of necessary accessories like hangers rods/Hilti anchor fasteners, sunken screws etc; complete. Allfactory finished

a Same as above specification but the size of the pelmetshall be 150x150mm

RMT 15

b Same as above specification but the size of the pelmetshall be 300x150mm

RMT 465



238 Providing and fixing Drapery rod, using decorativealuminium tubular pipe with approved color powdercoating of required length. Rate to include side coveringheads, required number of holding bracket and necessaryhardwares etc.

RMT 1126

239 Providing sill level covering 150mm to 300mm wide with18mm thick 1st quality jet black granite of approvedshade set in Laticrete adhesive L290 including pointingwith Latapoxy SP 100 joint filler compound of Laticrete orapproved matching shade and all as per Manufacturer'sSpecification. Rate shall include for making edge bullnoising with good polishing, preparation of base surfaceand acid wash at all levels and as directed.

RMT 465

240 Providing and fixing of Digitally reproduced Scotch printdecorative 3M graphics (with controltac & comply featurefor direct, bubble-free application on walls) as per thetheme selected by clients with UV protective matte overlaminate. Customized imagery. The rate shall be inclusiveof material, Hardware for fixing the graphics and fixing

charges etc.

Sqm. 10

241 Providing and fixing of imported wall paper of approveddesign, fixing details as per manufacturer standard etc allcomplete as directed by the Engineer-Incharge.

Sqm. 20

242 Providing and fixing matt finish white mark writing

board of enamelled sheet steel front, GI back overapproved inner core, of specified size black or chocolatecolour anodised aluminium beading to form the screenincluding the necessary accessories such as magneticsymbols, magnetic letters, magnetic strips, magneticeraser, magnetic dry marker 4 Nos., spare felt for eraser,board fixing clips etc. and the board shall be made out ofenamelled sheet with backing of AC sheet to suitablethickness etc. complete and all as per manufacturer'sspecification and as directed by the Engineer-Incharge.The rate include excise duty, sales tax and surcharge,central excise duty, delivery charges and fixing charges, ifany etc. complete and all as directed by the Engineer-Incharge/Consultant. Rate shall inclusive of making andfixing wooden ledge for full length of the board forkeeping marker pen, eraser etc. Rate quoted shall be forthe complete finished work including ledgeboard to keepaccesories , and all materials and labour mentioned above.

a Size of 2400 x 1200mm(meeting room) Nos 3

b Size of 1800 x 1200mm Nos 1

c Size of 1500 x 1200mm (Head room) Nos 3

d Size of 450x600mm(cabins) Nos 94



243 Providing and fixing vertical blinds with 89/75 mm wide

imported superior polyster base fabric vanes withScotchguard application as per approved sample, make ofVista Levellor or approvred equivalent make and theranges of louver shall be in ' Select and Classsic'. Thevertical blinds shall have a head rail of extruded anodisedhigh strength aluminium alloy, shall be 25 mm x 50 mmhigh or equivalent with wall thickness of 1.2 mm orequivalent. End control units consists of reductiongearbox having the reduction ratio of 3.:5:1 for a verysmooth operation of the blind.This unit consists ofplanetry gear in the outer housing,four small tranmissiongears fitted in the middle assembly and a end receivinggear attached to central sprocket unit.

Tilter chain is made of 4.5mm plastic beads moulded on2.2mm thick polyster card.The pitch of the beads is6mm.The end control unit have the facility to rotate thelouver by 180 degrees.Tilt rod is made of extrudedaluminium having 3 keyways and the average dia shasll

be 5.8 mm .Carrier ( Runner ) is made of moulded plastichaving anti friction additive.It consists of polymerhousing with wheels mounted on sides & has a gear andworm mechanism with vertical worm fixed with atongued poly-carbonate stem to hold the louvers. Spaceris made of Moulded Derlin having friction additive.

The vanes shall be capable of 180 deg. rotation in positionand shall be of polyester / viscose yarn dyed in fast colorsa strain resistant chemicals treatment or equivalentprotective coating shall be applied on vanes. Theinstallation shall be complete in all respects.(N&S)

Sqm. 841

244 Specification same as above but the fabric shall be madeof specially coated non-curl Blackout fabric to repel oil /water / stains, with complete fittings and front valance asper approved sample and make including reduction geartilter louver (E)

Sqm. 2

245 Providing & fixing Motorized Black out Roller blinds

conforming to specifications

The Drive units -Shall be of Moulded plastic withrectangular support pin and inserted into the tube end .Itshall be driven by a ball chain pulley with ball chain andcan be positioned at right hand or left hand side of theshade. The shade when lowering or raising ,shall be

automatically locked in position upon release of the ballchain by means of built in friction lock

End Plug-Shall be Moulded of plastic with allocation pin.The plug shall be inserted into tube end.(Opposite todrive unit)



Support Brackets-Shall be of zinc plated steel & providedwith moulded plastic covers and used in right hand or lefthand positions differentiated by the acceptance of therectangular drive unit support or the round idler plug pin

Bottom Rails-Shall be stiffening element inserted into abottom rod pocket. The material may be timber ,PVCcovered steel tube or VB bottom rail.Ball Chain -Shall be 2mm diameter cord with 4.5mmdiameter acetal balls moulded co-axially to it on 6mmpitch to form a endless ball chain .It is used for raising orlowering action of the shades.Fabric-1)Basic material -100% polyster2)fabric weight -170g/sqm3)Thickness -4mm 5)Finishing -Blackout fabric,reverse & front side pigment color coatedLight Fitness -Confirming to DIN54004/DIN EN ISO 105-B02>/5-6 Shrinkage % ge-Confirming DIN 53892 B2<0.5% Light reflection -82% Light transmission -0% Lightabsorption -18%

Sqm. 60

246 Providing and fixing of window curtain with necessary

fleecy and folds of approved make, color and pattern etc..all complete as directed by the Engineer-Incharge.

Sqm. 170

247 Providing and fixing plywood 8mm BWR ply, rate shallbe inclusive of necessary hardware, adhesives wastageand necessary edge beading etc. at level.

Sqm. 5

248 Preparing the surface, making and fixing of POP cornice

at the junction of wall and ceiling. The rate shall beinclusive wastage, mould, scaffolding, cleaning thesurface etc. size as mentioned below

a size diagonally 150mm RMT 1350

b size diagonally 200mm RMT 6500

249 Providing and fixing of key cupboard all as per drawing

detail, using 18mm thick BWR ply for all vertical andhorizondal, providing glass shutter with necessary framesand all the surfaces of ply shall be finished with 1mmthick laminate of approved shade. The rate shall beinclusive of wastage, necessary hardware hinges, handle,Key hooks, lock and tower bolt etc. all the woodensurfaces shall be finished with sealer polish. size600x900x300mm

Nos 4

250 Supplying and fixing of MS powder coated Letter Box ofapproved size and shape as per drawing as directed 1150ht x 900 w x 100D. Cluster of 21 Boxes

Nos 3

251 Providing and fixing of mirror But in general 6mm thick

mirror with aluminium frame for backing frame fixingwith 12MM thick BWR ply fixing with stainless steelstuds.

Sqm. 35



252 Providing and fixing of 50mmx50mm size Column

Corner Guard (DURAL or equivalent make), for verticalcorner's of RCC columns, Brick pillars, Brick walls,Partitions, using sub frame of 1.5mm thick aluminiumprofile fixed in to the above corner surfaces by usinganchor fasteners. Then the top covering with Rigid PVCpanel profile is to be fixed on the sub frame byinterlocking. The rate shall be inclusive of necessaryhardwares etc; complete as per drawing as directed.

RMT 87

253 Providing and fixing of netlon, using necessary all roundVelcro on the window frame and netlon. The rate shall beinclusive of necessary hardware, stapler etc.

Sqm. 413

254 Pigeon hole Rack: Providing and installing pigeon holerack size as shown in Dwg.but in general it shall be madeof 18mm BWR ply all exposed surfaces are finished with1.5mm tk. Laminate of approved colour shade. Rate shallbe inclusive of providing teakwood lipping of specifiedsizes, necessary hardware's etc;complete.(Size shall be

450mm deep and 2100mm ht. and pigeon hole size375mmx375mm).

Sqm. 2

255 Providing and fixing storage unit to a width of 600mm

and 2100mm height as per drawing but in general, it shallbe made out of 19 mm thick BWR plywood on all sidesand intermediate shelves with necessary and the openableshutter shall be made out of 19mm thick BWR plywoodwith necessary teakwood supports etc complete. Allexposed surfaces shall be finished with 1.5 mm thick

Laminate of approved shade and all inner / recessedsurfaces shall have 1mm thick laminate finish ofapproved shade. Rate to include all hardware's, autoclosing cabinet heavy duty hinges, handles - of approvedmake, including locking arrangements with master key ofapproved make etc. complete.(lab sample record)

RMT 170



256 Providing and fixing storage unit to a width of 600mmand 2700mm height and as per drawing but in general, itshall be made out of 1 mm thick BWR plywood on allsides and intermediate shelves with necessary and theopenable shutter shall be made out of 18mm thick exteriorgrade partical board for all vertical and horizontal.etccomplete. All exposed and hiden surfaces shall befinished with Merino Chem+ (Lab Grade) Chemical

Resistance Laminate or approved equivalent make

shade. All the exposed edges of 18mm thick particalboards shall be of postformed laminate and other hidenedges are finsied with 2mm thick PVC edge band. Rate toinclude all hardware's, auto closing cabinet heavy dutyhinges, SS handles - of approved make, including lockingarrangements with master key of approved make etc.complete.(lab sample storage RGL)

RMT 38

257 Lab Counter with Storage Cabinet:Providing and fixinggranite counter to a minimum width of 600 mm and to

a specified height as shown in drawing(750 to900mm) but in general, the counter top shall be made of18mm thick water proof plywood topped with graniteslab of 18 mm thick Black colour. The rate shallinclude for the providing storage unit below withopenable shutters. The top, bottom and intermediate shelfhaving 18 mm thick water proof plywood with 1.5 mmthick laminate. The openable shutter shall be made of 18mm thick BWR plywood finished with laminate includinghardwares like handles,hinges, ball catches etc.complete.Rate shall be inclusive of providing SS sink with drainboard, garbo drain of approved make at specifiedlocation. Rate shall be inclusive providing watersupply inlet and drainage outlet for each floor as per sitecondition. The rate shall be inclusive of all CP sanitaryaccessories such as pillar cock, bottle trap, angle valve etc.of Jaguar make.

RMT 100

258 Sink and wash basin bottom covered with louvered

shutter:

Providing and fixing of to a specified height as shown indrawing(750 to 900mm) but in general the counter bottomframe of 75x37mm first class teak wood at top andverticals at 900mm c/c. The openable shutter shall be

made of 18 mm thick BWR plywood with louvered all theexposed surfaces of ply finished with 1.5mm thicklaminate including hardwares like handles, tower bolt,hinges, ball catches etc.complete. All the exposed edges ofply shall covered with teak wood lipping. Rate shall beinclusive of applying melamine polish at all the teakwood surfaces and other hidden inside surfaces arecovered with sealer polish.

RMT 100



259 Providing Display unit as per drawing as directed madeof 19mm thick BWR ply on all sides with open frontconsisting of 10mm thick tinted toughened glass shelvesof 450/ 600mm width supported on to the plywood at 3levels in height and made to shape and pattern. Allexposed, internal ply surfaces shall be finished with3.5mm thick veneer of approved shade. Rate to includeproviding necessary hardware's, SS studs, etc .The totalheight of the unit shall be 2100mm. Rate quoted shall befor the complete finished work including all the materialsand labour mentioned above.( Size of display unit shall be3000x450x2100mm)

RMT 6

260 Providing and fixing book shelf storage unit to a width of300mm and 2100mm height as per drawing but ingeneral, it shall be made out of 19 mm thick BWRplywood on all sides and intermediate shelves withnecessary and the openable shutter shall be made out of19mm thick BWR plywood with necessary teakwoodsupports etc complete for bottom up to 900mm ht and

above providing 6mm thick toughened glass with pivetshutter. All exposed surfaces shall be finished with 1.5mm thick Laminate of approved shade and all inner /recessed surfaces shall have 1mm thick laminate finish ofapproved shade. Rate to include all hardware's, autoclosing cabinet heavy duty hinges, handles - of approvedmake, including locking arrangements with master key ofapproved make etc. complete.

RMT 15

261 Providing and fixing of backdrop at reception as perdrawing and as directed, in general it shall be made with12mm thick BWR ply with Acrylic sheet ONGC logo andnecessary backing lighting of LED etc all as per drawingdetails.

Sqm. 25

Total of Miscellaneous Works

TOILET CUBICLES of approved make Stelatex-

Singapore/ Merino/Greenlam Height of the door shall

be 1850mm and Height of the fixed, divider shall be

2100mm.Specification as follows and refer all as per drg.

And also Technical specification. (SOLID COLOUR)

262 Men's Rest Room

a 12mm thick HPL board with Standard necessaryaccessory and hardware form approved make pole base

Aluminium Nylon Polyamide Accessories of approvedmodel including Top rail of "U" channel.i)2100mm long (including 2 no of door 650mm width andfixed panel as per site condition)ii)Fixed divider panels 1500mm - 1no Set 3

b 12mm thick HPL board with Standard necessaryaccessory and hardware form approved make pole baseAluminium Nylon Polyamide Accessories of approvedmodel including Top rail of "U" channel.



i)1780mm long (including 2 no of door 650mm width andfixed panel as per site condition)ii)Fixed divider panels 1500mm - 1no Set 1

263 Supplying and fixing of Urinal partition to the size of size1290 X 500 mm made out of 12mm thick toughened glasswith approved design and pattern of etching, includingthree sides of beveled edge polishing and finishing. Thepartition is to be fixed into the wall using suitable size SSbrackets with anchor Bolts, Nuts, washers, grouting etccomplete in all respects as directed by the Engineer-In-charge.

Set 14

264 Ladies Rest Room

a 12mm thick HPL board with Standard necessaryaccessory and hardware form approved make pole baseAluminium Nylon Polyamide Accessories of approvedmodel including Top rail of "U" channel.i)2185mm long (including 2 no of door 650mm width andfixed panel as per site condition)ii)Fixed divider panels 1550mm - 1no Set 3

b 12mm thick HPL board with Standard necessary

accessory and hardware form approved make pole baseAluminium Nylon Polyamide Accessories of approvedmodel including Top rail of "U" channel.i)2550mm long (including 3 no of door 650mm width andfixed panel as per site condition)ii)Fixed divider panels 1550mm - 2no Set 1

c 12mm thick HPL board with Standard necessaryaccessory and hardware form approved make pole baseAluminium Nylon Polyamide Accessories of approvedmodel including Top rail of "U" channel.i)1000mm long (including 1 no of door 650mm width andfixed panel as per site condition)

Set 2

265 Providing and fixing MTS Multi Trim System-

ATT42/PBT12-Aluminium Top & PVC-u Base. (Providing& fixing Gradus ATT-42/12 transition plate of approvedsample section of size 42mmx42mm for the junction oftiles/granite flooring with carpet. Aluminium anodisedprofiles shall be screwed neatly to the flooring withDowelRib screws)

RMT 20

266 Providing and fixing Transition T Profile Aluminium-TP291F4 ( Old type SP20AS). (Providing & fixing GradusSP20-AS - new code TP291F4 tansition plate of approvedsample section of size 20mm width for the junction oftiles/granite flooring with carpet. Aluminium anodisedprofiles shall be screwed neatly to the floooring with

DowelRib screws)

RMT 20

Total of Cubical Works

MODULAR WORKS



267 Single Person Workstation(Rockworth or

approved equivalent make) of overall Size 1200 X1500mm x 1200 H as per drawing and consisting ofthe following for each person: a) The work top shallbe of 25mm thick exterior grade prelaminated particleboard cut as per shape and design as shown in drawing.The edge of the top shall be finished with 2mm thick PVCedge banding, one no of PVC wire manager with covermatching the laminate. b) Providing & keeping inposition of Pedestal Storage unit of size 450mm x 450mmx 700mm ht, it shall be made of CRC framework on threeside & MDF with laminate finish on the front side with2mm thick PVC edge banding / Postformed top surface.Storage units to have three drawers (one filing drawerand two equal drawers), with required locking system.With necessary accessories like locks, SS brush finishedhandle, 4nos of Nylon double wheel with lockingprovision and required hardware etc., c) 1 No.magnetic writing board . d) 1 No fabric Pin-upboard (approved fabric costing not less than Rs. 150 /

RM)

e) Shall be provided with UPS / Raw Power and Data /Telephone raceways - 2 nos. 1 No. shall be providedbeneath the work top and the other one shall be at floorskirting level.f) The partition shall be made of allaluminium frame finished with powdercoating/anodized, covered with combination of fabricand exterior grade laminated board. Each workstation tohave one writing board and a pin up board. The thicknessof partition shall be 65/60 mm and the height shall be of1200mm.g) Providing and fixing of acrylic sheet nameplate holder (size 60mm wide x 300mm long)h) The end

trims, top runners shall be aluminium anodized/powdercoated in finish and sharp corners shall be avoided. i)Powder coated key board tray

j) 1 No. Mobile CPU trolley made of CRC steel powdercoated or MDF epoxy painted finish.Note: Rate to include intermediate and end partitions alsoas per drawings and as instructed by Engineering-incharge.

a Workstation size 1800x1500mm : Nos 6

b Workstation size 2100x2600mm : Nos 10



268 Providing and fixing of DH cabin table (Hermanmiller

posh or approved equivalent make) of size2700x1200mm side table 1600 x 600mm, made to shapeand design, but the table top shall be made of 25 mm thickexterior grade prelaminated particle board with necessarysupports in criss-cross manner, details as directed/ shownin dwg, and the table top and all exposed surfaces shall befinished with approved shade. Rate shall be inclusive ofproviding MS powdercoated articulated keyboard, 50mmdia wire manager and PVC edge banding with necessaryhardwares etc., complete. 1 No. Providing & keeping inposition of Pedestal Storage unit of size 450mm x 450mmx 700mm ht, it shall be made of CRC framework on threeside & MDF with laminate finish on the front side with3mm thick PVC edge banding / Postformed top surface.Storage units to have three equal drawers, with individuallocking system. With necessary accessories like locks, SSbrush finished handle, 4nos of Nylon double wheel withlocking provision and required hardware etc.. as directed.

But the finishes shall be with veneer and melamine polish. Nos 6

269 Providing and fixing of cabin table (Rockworth orapproved equivalent make) of aproximate size 2400length x 900mm, side table size 1500x600mm, made toshape and design, but the table top shall be made of 25mm thick exterior grade prelaminated particle board withnecessary supports in criss-cross manner, details asdirected/ shown in dwg, and the table top and allexposed surfaces shall be finished with approved shade.Rate shall be inclusive of providing MS powdercoatedarticulated keyboard, 50mm dia wire manager and PVC

edge banding with necessary hardwares etc., complete.

Nos 19

270 Providing & keeping in position of Pedestal Storage unitof size 450mm x 450mm x 675mm ht, it shall be made ofCRC framework on three side & MDF with laminatefinish on the front side with 3mm thick PVC edgebanding / Postformed top surface. Storage units to havethree drawers(one filing drawer and two equal drawer),with individual locking system. With necessaryaccessories like locks, SS brush finished handle, 4nos ofNylon double wheel with locking provision and requiredhardware etc.. as directed.

a Size shall be 2100x750 and side table size 1200x600mm Nos 53

b Size shall be 1800x750 and side table size 1050x450mm Nos 39

c Size of the table shall be 900x600mm for sample stores Nos 8



271 Running counters:Providing and fixing counter top(Rockworth or approved equivalent make) to a width of600 mm and 750 mm high made to shape and size shownin drawing ,using 25mm thick exterior gradeprelaminated particle board with necessary bracketsupports both in horizontal and vertical directions. All theedges of table top shall be provided with matching edgebanding. Each person shall have one key board tray,hanging drawer unit consists of 2 drawers, using 18mmthick exterior prelaminated particle board etc withnecessary hardwares and 1 No. of MS powder coated wiremanager 50 mm dia. should be provided for each personand powder coated articulated metal key board / drawerunit shall run on sliding runners of approved make. ( Forserver, printer station etc). Storage shutters shall be madeout of 18mm prelaminated particle board in. The rate shallbe all inclusive of providing privacy partitions of 10mmfrosted glass/ fabric wrapped panel of size 600mm wideand height 450mm as per drawing.

RMT 28

272 Running counter with partition :(Rockworth or

approved equivalent make)

Providing and fixing of counter top of width 600mm ingeneral it shall be made of 25mm thick exterior gradeprelaminated partial board of approved shade with 2mmthick PVC edge bands, all exposed front edges of thework surfaces to be rounded. The top shall be be fixed to69/60mm thick Partition facing outside to the corridor ofworkstation to be of panels of pre laminated boards ofexterior grade/fire retardant fabric facing inside write onboard and magnetic soft board at above table top andbelow table top shall be pre laminated boards of exteriorgrade/fire retardant fabric .

The frames & caps to be of extruded aluminium sectionspowder coated to approved colour(not less than 50microns thick) Trim at 1200 mm height, exposed end to berounded Tile to glued to the frame with clip-onmechanism or set into grooves as the case may be ,but tobe highly modular & elastic. The corner post of all framesto be designed for 90 degree connections in cluster ofvarious sizes.The partitions to comprise of at least two raceways foreffective wire management(one for power & other for

data, one above table top & other at skirting level) Withvertical raceway (If any) .The cover to be provided withnecessary cutout for electrical & data socket outlets. Theraceway to consist of necessary clipping mechanisms tofasten cables.Cost to include wastages mockup, all handling,transportation etc., Note: No Formaldehyde should beused in making of workstation or during placing of thework stations

RMT 2



273 Supplying and fixing of freestanding storage units(Rockworth or approved equivalent make), 450mm depthand 750mm height ( matching to the workstation table topheight ) made of 18 mm thick both sides prelaminatedparticle boards of exterior grade for vertical andhorizontals and intermediate shelves. The openable doorshutters shall be provided with SS handles, locks, autoclosing hinges and necessary hardwares etc; complete.The exposed edges shall be finished with 2mm thick PVClipping.(rear side storage )

RMT 185

274 Storage Units: Providing and fixing rear storage unit to awidth of 600mm and 750mm height as per drawing No....It shall be made out of 25 mm thick exterior gradeprelaminated board on all surfaces including top, withintermediate shelves and the openable shutter shall bemade out of 18mm exterior grade prelaminated particleboard laminated on both sides. Rate shall include forproviding edge banding etc. complete. Rate to include allhardwares, auto closing cabinet heavy duty hinges,

handles - of approved make, including lockingarrangements with master key of approved make etc.complete.(meeting)

RMT 10

275 Storage Units:Providing and fixing rear storage unit to awidth of 450mm and 1200mm height as per drawingdetails It shall be made out of 25 mm thick exterior gradeprelaminated board on the top and all surfaces other thanthe top with intermediate adjustable shelves and theopenable shutter shall be made out of 18mm exteriorgrade prelaminated particle board laminated. All edgesshall be PVC edge banded of 2mm thick on the exteriorand all internal surfaces with 1mm thick PVC edge

banding. Rate to include all hardwares, auto closingcabinet heavy duty hinges, handles -of approved make,including locking arrangements with master key ofapproved make.

RMT 5

276 Storage Units: Providing and fixing rear storage unit to awidth of 600mm and 1200mm height as per drawingdetails It shall be made out of 25 mm thick exterior gradeprelaminated board on the top and all surfaces other thanthe top with intermediate adjustable shelves and theopenable shutter shall be made out of 18mm exteriorgrade prelaminated particle board laminated. All edges

shall be PVC edge banded of 2mm thick on the exteriorand all internal surfaces with 1mm thick PVC edgebanding. Rate to include all hardwares, auto closingcabinet heavy duty hinges, handles - of approved make,including locking arrangements with master key ofapproved make.

RMT 2



277 Storage Units: Providing and fixing rear storage unit to awidth of 450mm and 2100mm height as per drawingdetails It shall be made out of 25 mm thick exterior gradeprelaminated board on the top and all surfaces other thanthe top with intermediate adjustable shelves and theopenable shutter shall be made out of 18mm exteriorgrade prelaminated particle board laminated. All edgesshall be PVC edge banded of 2mm thick on the exteriorand all internal surfaces with 1 mm thick PVC edge

banding. Rate to include all hardwares, auto closingcabinet heavy duty hinges, handles - of approved make,including locking arrangements with master key ofapproved make.

RMT 2

278 Storage Units:Providing and fixing rear storage unit to awidth of 600mm and 2100mm height as per drawingdetails It shall be made out of 25 mm thick exterior gradeprelaminated board on the top and all surfaces other thanthe top with intermediate adjustable shelves and theopenable shutter shall be made out of 18mm exterior

grade prelaminated particle board laminated. All edgesshall be PVC edge banded of 2mm thick on the exteriorand all internal surfaces with 1 mm thick PVC edgebanding. Rate to include all hardwares, auto closingcabinet heavy duty hinges, handles -of approved make,including locking arrangements with master key ofapproved make as directed.

RMT 2

279 Providing and fixing of filing compactor (Optimizer 457x915 x 1980mm) units of Godrej or approved equivalentmake as per manufacturer's specification.(all sample &record room)

RMT 73

280 Providing and fixing Discussion table of circular shape

of 1200mm dia, made to shape and design, but in generalthe table top shall be made out of 25 mm thick exteriorgrade prelaminated particle board over 150mm diapowder coated MS pipe with necessary supports, baseand framing, and the table top and all exposed surfacesshall be finished with approved shade of 1mm thicklaminate finish. Rate shall inclusive of matching edgebanding with necessary hardwares etc., complete.(library& recreational block first floor)

Nos 4



281 Making and assembling of reading Table (Hermanmiller

posh or approved eauivalent make) of specified size1800x1200mm, made to shape and design, but in generalthe table top shall be made of 25 mm thick exterior gradeparticle board with 0.8mm thick post-formed laminate ofapproved shade, with adequate CRC metal supports incriss-cross manner as per your standard with modestypanel. (supporting system shall be approved by Engineer-Incharge), Rate shall be inclusive of two side 2mm thickPVC edge band, cable raceway, necessary hardware'sinclusive of supply and fixing of Magnum POP-up boxesas per mock up approval) etc., complete. The bottomsupport structure shall have openable arrangement for thepurpose of easy cable management.

Nos 3

282 Making and assembling of Meeting Room Table

(Hermanmiller posh or approved eauivalent make) ofspecified size made to shape and design, but in generalthe table top shall be made of 25 mm thick exterior grade

particle board with 0.8mm thick post-formed laminate ofapproved shade, with adequate CRC metal supports incrisscross manner as per your standard with modestypanel. (supporting system shall be approved by Engineer-Incharge), Rate shall be inclusive of two side 2mm thickPVC edge band, cable raceway, necessary hardware'sinclusive of supply and fixing of Magnum POP-upboxes(required number of POP box as per mock upapproval) etc., complete. The bottom support structureshall have openable arrangement for the purpose of easycable management also the cables shall not visible. as perdrawing.

a Table of size - 5500mm x 1200mm Nos 2b Specification same as above but the finishes shall be with

veneer and melamine polish instead of laminate.Nos 1

283 Providing & keeping in position of Pedestal Storage unit

of size 450mm x 450mm x 675mm ht, it shall be made ofCRC framework on three side & MDF with laminatefinish on the front side with 2mm thick PVC edgebanding / Postformed top surface. Storage units to havethree drawers(one filing drawer and two equal drawers),with individual locking system. With necessaryaccessories like locks, SS brush finished handle, 4nos of

Nylon double wheel with locking provision and requiredhardware etc.

Nos 5

284 Supplying of 1 No. Mobile CPU trolley made of CRC steelpowder coated or MDF epoxy painted finish.

Nos 5

285 Providing and fixing of 1 No. powder-coated metal Keyboard tray of size 530 (W) x 350 (D) x 40mm H withtelescopic drawer slides as per drawing

Nos 5



286 Supplying and installation of dining table of size

1000x1000mm. Frame made with 12 gauge SS pipe 50mmdia for supporting leg and 25mm dia pipe for crossbrazing frames shall be as per drawing. Table top shall bemade with 25mm exterior grade MDF covered with0.8mm thick post-formed laminate on 2 sides and other 2sides finished with PVC edge band.

Nos 6

Total of Modular Works Wardrobe

287 Providing and fixing Wardrobe including loft as perdrawing but in general, it shall be made out of 18 mmthick Particle Board of Action Tesa make or approvedequivalent on all sides including top, with intermediateshelves with necessary PVC supports, finishedwith approved shades of Laminate. The open ableshutter and shall be post formed and shall be made out of18mm thick Particle Board and external surface shallbe finished with MR Grade Laminate of Merino orapproved equivalent. Rate shall include forproviding matching 2mm PVC Lipping for shelves and

dividers, made of Particle Board of Action Tesa make orapproved equivalent ,as required. All exposed surfacesshall be finished with 1.5 mm thick laminate of approvedshade and all inner / recessed surfaces shall finishedwith 1mm laminate. Shutter back side shall be finishedwith 1mm thick Laminate of approved shade.

Rate shall be inclusive of providing and fixing mirror onshutter as per drawing. The rate shall also include forfixing all the hardware and accessories fixing labour,electricity, all complete from Hettich / Haffele / Blum orapproved equivalent. The hardware shall be inclusive ofbut not limited to the following hardware and accessoriesin Hettich or approved equivalent make-Ecomat serieshinges, Garment Rails 30x15mm for required length asper drawing including supports as necessary, telescopicrunner channel for drawers, locking arrangements for allinternal drawers and external shutter including masterkey with Multipurpose Drawer Square Lock 32mm etc.complete. Note: All wire baskets, accessories, handles etcshall be of SS 304 grade. (Type C,

Bachelor Units, Transit Room Wardrobes)

a Wardrobe of size 3000x600mm x 2850mm Ht. (incl Loft) Set 64

b Wardrobe of size 1000x600mm x 2100mm Ht. Set 64

c Wardrobe for dresser unit of size 700x600mm x 2100mmHt.

Set 64

d Wardrobe of size 1590x500mm x 2850mm Ht. (incl Loft) Set 128

e Wardrobe of size 1850x600mm x 2850mm Ht. (incl Loft) Set 28



f Wardrobe of size 1200x600mm x 2850mm Ht. (incl Loft) Set 2

g Wardrobe of size 1950x600mm x 2850mm Ht. (incl Loft) Set 12

h RC Loft above Store (only shutters) of length 1630mm x750mm Ht.

Set 66

288 Providing and fixing Wardrobe including loft as perdrawing but in general, it shall be made out of 18 mmthick Particle Board of Action Tesa make or approvedequivalent on all sides including top, with intermediateshelves with necessary PVC supports, finished withapproved shades of Laminate. The open able shutter andshall be post formed and shall be made out of 18mm thickParticle Board . Rate shall include for providing matching2mm PVC Lipping for shelves and dividers, made ofParticle Board of Action Tesa make or approvedequivalent ,as required. All exposed surfaces shall befinished with 1.5 mm thick laminate of approved shadeand all inner / recessed surfaces shall finished with 1mmlaminate. Shutter back side shall be finished with 1mm

thick Laminate of approved shade.

Rate shall be inclusive of providing and fixing mirror onshutter as per drawing. The rate shall also include forfixing all the hardware and accessories fixing labour,electricity, all complete from Hettich / Haffele / Blum orapproved equivalent.The hardware shall be inclusive ofbut not limited to the following hardware and accessoriesin Hettich or approved equivalent make-Sensys serieshinges for the wardrobes and Ecomat series hinges for theloft shutters, Garment Rails 30x15mm for required lengthas per drawing including supports as necessary,telescopic runner channel for drawers in Quadro Series,

locking arrangements for all internal drawers and externalshutter including master key with Multipurpose DrawerSquare Lock 32mm etc. complete. Note: All wire baskets,accessories, handles etc shall be of SS 304 grade.(Type D

and VIP Transit Rooms Wardrobes)

a Wardrobe of size 3000x600mm x 2850mm Ht. (incl Loft) Set 4

b Wardrobe of size 1000x600mm x 2100mm Ht. Set 2

c Wardrobe for dresser unit of size 700x600mm x 2100mmHt.

Set 2

d Wardrobe of size 1590x500mm x 2850mm Ht. (incl Loft) Set 4

e RC Loft above Store (only shutters) of length 1630mm x750mm Ht.

Set 2

f Wardrobe of size 1350x500mm x 2850mm Ht. (incl Loft) Set 2

g Wardrobe of size 3350x500mm x 2850mm Ht. (incl Loftand space for luggage rack and microoven as perdrawing)

Set 2

Total of Wardrobe



289 Crockery Unit

Providing and fixing Crockery Unit including loft as perdrawing but in general, it shall be made out of 18 mmthick Particle Board of Action Tesa make or approvedequivalent on all sides including top, with 10mmtoughened glass intermediate shelves with necessary PVC/ Steel supports. The open able shutter and shall be of10mm toughened glass with Aluminum frame. Rate shallinclude for providing matching 2mm PVC Lipping forvertical dividers, made of Particle Board of Action Tesamake or approved equivalent ,as required. All exposedsurfaces shall be finished with 1.5 mm thick laminate ofapproved shade and all inner / recessed surfaces shallfinished with 1mm laminate.

The rate shall include for fixing all the hardware andaccessories fixing labour, electricity, all complete fromHettich / Haffele / Blum or approved equivalent. Note:

All wire baskets, accessories, handles etc shall be ofminimum SS 304 grade. The hardware shall be inclusive

of but not limited to the following hardware andaccessories in Hettich or approved equivalent make-Intermat-9943 Alu Frame Hinge '0' Crank hingesincluding supports as necessary, Ecomat series hinges forthe loft shutters, etc. complete. (Type C & Type D)

Crockery Unit of size 3000x420mm x 2850mm Ht. (inclLoft)

Set 66

Total of Crockery Unit

Kitchen

290 Providing and fixing Modular Kitchen of approved makeincluding loft as per drawing but in general, it shall bemade out of 18 mm thick BWR Ply of Action Tesa make orapproved equivalent on all sides including top, withaccessories, drawers and intermediate shelves as perdrawings and specification with necessary PVC / Steelsupports. The open able shutter and drawer front shall bepost formed on 2 sides and 2 mm pvc edge banding onother 2 sides and shall be made out of 18mm thick BWRPly and external surface shall be finished with MR GradeLaminate of Merino or approved equivalent. Rate shallinclude for providing matching 2mm PVC Lipping forshelves and dividers, made of 18mm thk BWR Ply ofAction Tesa make or approved equivalent ,as required.All exposed surfaces shall be finished with 1.5 mm thick

laminate of approved shade and all inner / recessedsurfaces shall finished with 1mm laminate.



The counter top shall be finished with suitable supportsand shall be made of two layers of 18mm thick BWRplywood. Rate shall be inclusive providing and fixing ofSS sink with drain board of Nirali or approved equivalentmake (Model: Super Slider Satin finish-850X510mm),garbo drain of approved make at specified location etc.,complete. Rate shall be inclusive of making provision forfixing of Chimney hood including ducting till the externalwall and exhaust outlet point, of approved make atspecified location etc., complete, as directed.

The rate shall include for fixing all the hardware andaccessories fixing labour, electricity, all complete fromHettich / Haffele / Blum or approved equivalent. Thehardware shall be inclusive of but not limited to thefollowing hardware and accessories in Hettich orapproved equivalent make-Ecomat series hinges, Intermat9943 Alu Frame Hinge '0' Crank hinges includingsupports as necessary, telescopic runner channel fordrawers, skirting clip, etc. complete.

a Type C Kitchen of size 2550x600mm x 2850mm Ht. (incl

Loft) + 1800x600mm x 2850mm Ht. (incl Loft) as per

drawing. Rate shall include for providing and fixingAccessories as mentioned below in Hettich or approvedequivalent make-Note: All wire baskets, accessories,handles etc shall be of minimum SS 304 grade.

Set 64

2 nos Wire Basket Plain with Channels, hardware andsupports as required for drawer of Size 900 x 600 x Ht325mm each with 300mm Handle4 nos Wire Basket Plain with Channels, hardware andsupports as required for drawer of Size 450 x 600 x Ht325mm each with 150mm Handle2 nos Wire Basket - Plate with Channels, hardware andsupports as required for drawer of Size 600 x 600 x Ht300mm each with 150mm Handle2 nos Wire Basket - Cup & Saucer with Channels,hardware and supports as required for drawer of Size 600x 600 x Ht 200mm each with 150mm Handle2 nos Cutlery Tray with Channels, hardware and supportsas required for drawer of Size 600 x 600 x Ht 150mm eachwith 150mm Handle1 nos Bottle Pull Out with Frame Silent H599 Silver,Frame Silent Front Angle, 2 nos Frame Baskets of 160mm

each, hardware and supports as required for drawer ofSize 300 x 600 x Ht 650mm each with 150mm Handle

1 nos Tall Unit with Dispensa Frame Silver 362/1900-2300, Dispensa Full Extension Silent 1000 N Silver, 2 nosDispensa Front Stabilisator Silver, 5 nos Dispensa Clip-OnBasket of 400mm each, hardware and supports asrequired for tall unit of Size 450 x 600 x Ht 2100mm eachwith 450mm Handle



1 nos Dish Drainer Rack Set SS 600 with shutter in cabinetof size of size 600 x 300 x Ht 650mm each with shutter,hardware and supports as required for each with 150mmHandle6 nos Above Counter wall cabinets with 2 Flap Stay Basicin each shutter, hardware and supports as required forcabinets of size 600mm Width x 350mm Ht each with150mm Handle1 nos Waste Bin It Classic 13lts capacity fixed to the insideof shutter in the cabinet below the sink of size 600x 600 xHt 650mm with shutter, hardware and supports asrequired for each with 150mm HandleRemaining cabinets and loft with size as per drawing withshutters, ecomat hinges, hardware and supports asrequired for each with 150mm Handles

b Bachelor Units Kitchen of size 2850x600mm x 2850mm

Ht. (incl Loft) + 1000x600mm x 800mm Ht as per

drawing. Rate shall include for providing and fixingAccessories as mentioned below in Hettich or approvedequivalent make-Note: All wire baskets, accessories,

handles etc shall be of minimum SS 304 grade.

Set 28

4 nos Wire Basket Plain with Channels, hardware andsupports as required for drawer of Size 450 x 600 x Ht325mm each with 150mm Handle2 nos Wire Basket - Plate with Channels, hardware andsupports as required for drawer of Size 600 x 600 x Ht300mm each with 150mm Handle2 nos Wire Basket - Cup & Saucer with Channels,hardware and supports as required for drawer of Size 600x 600 x Ht 200mm each with 150mm Handle2 nos Cutlery Tray with Channels, hardware and supportsas required for drawer of Size 600 x 600 x Ht 150mm eachwith 150mm Handle1 nos Waste Bin It Classic 13lts capacity fixed to the insideof shutter in the cabinet below the sink of size 600x 600 xHt 650mm with shutter, hardware and supports asrequired for each with 150mm HandleRemaining cabinets and loft with size as per drawing withshutters, ecomat hinges, hardware and supports asrequired for each with 150mm Handles

c Transit - Common Kitchen of size 4150x600mm x

2850mm Ht. (incl Loft) as per drawing. Rate shall includefor providing and fixing Accessories as mentioned belowin Hettich or approved equivalent make-Note: All wire

baskets, accessories, handles etc shall be of minimum SS304 grade.

Set 1

2 nos Wire Basket Plain with Channels, hardware andsupports as required for drawer of Size 900 x 600 x Ht325mm each with 300mm Handle4 nos Wire Basket Plain with Channels, hardware andsupports as required for drawer of Size 450 x 600 x Ht325mm each with 150mm Handle



2 nos Wire Basket - Plate with Channels, hardware andsupports as required for drawer of Size 600 x 600 x Ht300mm each with 150mm Handle2 nos Wire Basket - Cup & Saucer with Channels,hardware and supports as required for drawer of Size 600x 600 x Ht 200mm each with 150mm Handle2 nos Cutlery Tray with Channels, hardware and supportsas required for drawer of Size 600 x 600 x Ht 150mm eachwith 150mm Handle2 nos Bottle Pull Out with Frame Silent H599 Silver,Frame Silent Front Angle, 2 nos Frame Baskets of 160mmeach, hardware and supports as required for drawer ofSize 300 x 600 x Ht 650mm each with 150mm Handle

1 nos Dish Drainer Rack Set SS 600 with shutter in cabinetof size of size 600 x 300 x Ht 650mm each with shutter,hardware and supports as required for each with 150mmHandle8 nos Above Counter wall cabinets with 2 Flap Stay Basicin each shutter, hardware and supports as required for

cabinets of size 600mm Width x 350mm Ht each with150mm Handle1 nos Waste Bin It Classic 13lts capacity fixed to the insideof shutter in the cabinet below the sink of size 600x 600 xHt 650mm with shutter, hardware and supports asrequired for each with 150mm HandleRemaining cabinets and loft with size as per drawing withshutters, ecomat hinges, hardware and supports asrequired for each with 150mm Handles

291 Providing and fixing Modular Kitchen of approved makeincluding loft as per drawing but in general, it shall bemade out of 18 mm thick BWR Ply of Action Tesa make orapproved equivalent on all sides including top, with

accessories, drawers and intermediate shelves as perdrawings and specification with necessary PVC / Steelsupports. The open able shutter and drawer front shall bepost formed on 2 sides and 2 mm pvc edge banding onother 2 sides and shall be made out of 18mm thick BWRPly and external surface shall be finished with MR GradeLaminate of Merino or approved equivalent. Rate shallinclude for providing matching 2mm PVC Lipping forshelves and dividers, made of 18mm thk BWR Ply ofAction Tesa make or approved equivalent ,as required.All exposed surfaces shall be finished with 1.5 mm thicklaminate of approved shade and all inner / recessedsurfaces shall finished with 1mm laminate.



The counter top shall be finished with suitable supportsand shall be made of two layers of 18mm thick BWRplywood. Rate shall be inclusive of providing and forfixing of SS sink with drain board of NIRALI orequivalent of approved make at specified location etc.,complete. ( Model. No. SUPER SLIDER SATIN FINISH )Rate shall be inclusive of making provision for fixing ofChimney hood including ducting till the external wall andexhaust outlet point, of approved make at specifiedlocation etc., complete.

The rate shall include for fixing all the hardware andaccessories fixing labour, electricity, all complete fromHettich / Haffele / Blum or approved equivalent. Thehardware shall be inclusive of but not limited to thefollowing hardware and accessories in Hettich orapproved equivalent make-Drawers in Innotech Series,Sensys series hinges, Intermat-9943 Alu Frame Hinge '0'Crank hinges including supports as necessary, telescopicrunner channel for drawers in Quadro Series, skirting clip,

etc. complete.

a Type D Kitchen of size 2550x600mm x 2850mm Ht. (incl

Loft) + 1800x600mm x 2850mm Ht. (incl Loft) as per

drawing. Rate shall include for providing and fixingAccessories as mentioned below in Hettich or approvedequivalent make-Note: All wire baskets, accessories,handles etc shall be of minimum SS 304 grade.

Set 2

2 nos Innotech Basket Plain with Channels, hardware andsupports as required for drawer of Size 900 x 600 x Ht325mm each with 300mm Handle4 nos Innotech Basket Plain with Channels, hardware andsupports as required for drawer of Size 450 x 600 x Ht325mm each with 150mm Handle2 nos Innotech Basket - Plate with Channels, hardwareand supports as required for drawer of Size 600 x 600 x Ht300mm each with 150mm Handle2 nos Innotech Basket - Cup & Saucer with Channels,hardware and supports as required for drawer of Size 600x 600 x Ht 200mm each with 150mm Handle2 nos Cutlery Tray with Channels, hardware and supportsas required for drawer of Size 600 x 600 x Ht 150mm eachwith 150mm Handle1 nos Bottle Pull Out with Frame Silent H599 Silver,

Frame Silent Front Angle, 2 nos Frame Baskets of 160mmeach, hardware and supports as required for drawer ofSize 300 x 600 x Ht 650mm each with 150mm Handle

1 nos Tall Unit with Dispensa Swing 2000-2200 B. 400Silver, Dispensa Swing Over Extn. Silver, 2 nos DispensaFront Stabilisator Silver, 5 nos Dispensa Clip-On Basket of400mm each, hardware and supports as required for tallunit of Size 450 x 600 x Ht 2100mm each with 450mmHandle



1 nos Dish Drainer Rack Set SS 600 with shutter in cabinetof size of size 600 x 300 x Ht 650mm each with shutter,hardware and supports as required for each with 150mmHandle6 nos Above Counter wall cabinets with 2 Flap Stay Basicin each shutter, hardware and supports as required forcabinets of size 600mm Width x 350mm Ht each with150mm Handle1 nos Waste Bin It Classic 13lts capacity fixed to the insideof shutter in the cabinet below the sink of size 600x 600 xHt 650mm with shutter, hardware and supports asrequired for each with 150mm HandleRemaining cabinets and loft with size as per drawing withshutters, ecomat hinges, hardware and supports asrequired for each with 150mm Handles

Total of Modular Kitchen

Chairs (Hermanmiller posh or approved equivalent

make)

292 Making and Supply of Ergonomically designed approvedchairs which will meet all of the technical specifications

and features listed below approved model. i)Seat:-Approved color leather covered Moulded polyurethanefoam together with Moulded ABS seat with revolving.ii)Back:-Approved color leather covered Moulded

polyurethane foam together with Moulded ABS andextra adjustable lumber support. iii)Tilting:-

Synchronized tilting mechanism with revolving andmultiple locking. iv)Armrests :- The armrests are to bescratch and weather resistant with swivel & deothadjustable arm pad & option of PVC pad. v)Lifting:-

Gaslift provision to be provided. iv)Base:-Nylon basewith 5nos of wheel pedestal should be provided asdirected.

High back Executive chair with HEAD RESTsynchronized tilting mechanism with Multiple lockingsystems, ABS for seat, Leather back with extra lumberSupport with fine tuning for depth adjustment, withswivel & depth, Height and width Adjustable arm rest &gas lift for height adjustment, Nylon base withcastors.(DH, incharge )

Nos 84



293 Making and Supply of Ergonomically designed approvedchairs which will meet all of the technical specificationsand features listed below approved model.i)Seat:-

Approved color Fire Retardant Fabric covered Mouldedpolyurethane foam together with Moulded ABS seat withrevolving.ii)Back:-Approved color Fire Retardant Fabriccovered Moulded polyurethane foam together withMoulded ABS and extra adjustable lumbersupport.iii)Tilting:-Synchronized tilting mechanism withrevolving and multiple locking.iv)Armrests :- Thearmrests are to be scratch and weather resistant withswivel & deoth adjustable arm pad & option of PVCpad.v)Lifting:-Gaslift provision to be provided.iv ) B

Nylon base with 5nos of wheel pedestal should beprovided as directed.

a Medium Back with synchronized tilting mechanism withMultiple locking systems, ABS for seat, Mesh back withextra lumbar Support with fine tuning for depthadjustment, with fixed armrest, gas lift for heightadjustment, Nylon base with castors. (Lab area and visitorto incharge meeting)

Nos 338

b AERON Medium Back with synchronized tiltingmechanism with Multiple locking systems, Mesh for seatand back with extra lumbar Support with fine tuning fordepth adjustment, with fixed armrest, gas lift for heightadjustment, Nylon base with castors. (Conference)

Nos 51

294 Medium Back visitor chair with mesh back lumbersupport fixed armrest with cantilever base(lab visitor,library)

Nos 72

295 Supplying Breakout chairs of approved model in general

it shall be made with rigid polycarbonate sheet, framemade with 20mm dia SS 16 gauge thickness pipe for legs.The chairs are to be delivered in packed condition. Nodamage of any sort will be accepted before taking overand chairs damaged in transit shall be replaced free ofcost.Required warranty for the chairs for a period of oneyear shall be given.(SS 304 grade)

Nos 24

296 Providing and fixing sofa (Model: SQP -Hermanmillerposh or equivalent make) made to shape and pattern asper Approved model, but in general the sofa shall bemade out adequate size of teakwood frames in bothhorizontal and vertical directions and 2 nos. 4 mm thick

plywood in curved shape portion with necessary teakwood frames and supports to shape and profile. Rate toinclude to provide MM foam 150mm thick, leatheriteupholstery of approved make and design and ISI markhard wares etc. complete as directed.

a Single seater (App. Size 900 x 825 x 800) Nos 16

b Two seater ( App. Size 1400 x 825 x 800) Nos 20



297 Providing and fixing sofa side table (Model: SLO -Hermanmiller posh or equivalent make) made to shapeand pattern as per Approved model, side / centre table asper shape shown in the drawing made out of 19 mm thickBWR plywood as supports and at top provided with 12mm thick tinted etched glass with bevelled edge to thespecified shape and size. All exposed surface shall befinished with 3.5mm thick veneer of approved shadefinish with melamine as directed.

a a)600x450mm Nos 15

b b)1200x600mm Nos 7

Total of Chair Works

External Facade and Associated Works

General Note : Refer Particular specifications andTechnical specification, while quoting the rate for therespective items under this schedule. Also, the BOQ itemdescriptions shall be read in conjunction withcorresponding material specification and design criteria asspecified in the tender specification as well as particular

specification, in addition to the detailed specification andstandards specified in the corresponding codes andstandards. The quoted rate under this schedule shall bedeemed to have considered Technical specification andparticular specification.

298 Vision panel, Spandrel panel & Vision on spandrel panel(System with glass): For complete system designing,providing and fixing Semi Unitized structural glazingsystem with aluminium anodized extruded frames, HDGbrackets & SS anchors with vision panel, spandrel paneland vision on spandrel panel glass shall be Insulated

Glazed unit - 24 mm thick with 6 mm thick Reflective lowE coated glass on # 2 surface - Green Radiance of Asahimake or KT 455 Reflective coated glass of Saint Gobainmake as outer pane and 12 mm airgap and 6 mm thickuncoated clear glass as inner pane of same make. Bothpanes are heat treated. Rate including supplying andfixing of glass and Off site proto type test etc. The glasswill be selected at appropriate time by Engineer-Incharge.Refer Particular relevant technical Specification.

Sqm. 2300

299 Spandrel panel with ACP (System with ACP): Completesystem designing, providing and fixing Semi Unitized

structural glazing system with Spandrel panel havingLaminated sandwiched composite panel (Aluminiumcomposite panel) -4mm thick of approved make andcolour. Refer Technical specification for detailedspecification of Laminated sandwiched composite panel,which shall form part of this item. Rate shall include thecost for supplying and fixing of Laminated sandwichedcomposite panel with LDPE core (ACP), sealant and etccomplete. Refer Particular relevant Specification.

Sqm. 5



300 Spandrel panel (System glass): Complete systemdesigning, providing and fixing Semi Unitized structuralglazing system with aluminium anodized extrudedframes, HDG brackets & SS anchors with Spandrel panelwith Single Glazed unit (Monolithic glass) - 6mm thickReflective coated glass on # 2 surface - Super Silver Greenof Asahi make or ST 467 Reflective coated glass of SaintGobain make. Rate including supplying and fixing theglass. The glass will be selected at appropriate time byEngineer-Incharge. Refer Particular relevant technicalSpecification.

Sqm. 5

301 Hardware for top hung window: Extra rate over & abovethe Semi unitized structural glazing item above fordesigning, providing and fixing hardwares for top hungopenable outward shutter as per particular specification.Rate shall exclude cost of Glass and main frame, butinclude cost of sub frame for shutter. Refer Particularrelevant Specification.

Each 113

302 Insulation for Spandrel: Rock wool slab - 64 Kg/cum and

having 'K' value of 0.033 w/Mok - 50 mm thick wrappedwith factory pressed Black glass tissue and using 1.0mmthick Aluminium anodized tray with fold alround to aheight of 100mm minimum as thermal insulation to befixed behind Spandrel glass / Composite panel claddingarea as mentioned. All the edges between aluminiumanodized tray and frame to be sealed with Non-Stainingweather silicon sealant of approved make. ReferParticular relevant technical Specification.

Sqm. 690

FRAMELESS GLAZING (POINT FIXED / SPIDER

GLAZING) SYSTEM.

303 Frameless glazing system with Tensile Cable nettruss frame: Complete system forFrame less glazing with Cable truss / net system asmentioned in Particular Specification. Rate shall includecost of spiders suitable for laminated single / doubleglazed unit, Articulated bolts, required dia double /single stand SS pre tensioned cables to satisfy thestructural criteria, off site proto type test etc,.



a Frameless glazing system with Laminated DGU: Frameless glazing system with supplying and fixing of 33.52mm thick (13.52mm + 12mm Air gap + 8mm) LaminatedDouble glazed unit having 13.52 mm thick with 6mmthick Reflective low E coated Grey Lite of Asahi make or

Green Radiance of Asahi make or KT 455 Reflective

coated glass of Saint Gobain make as outer panel and 6mm thick uncoated clear glass as inner panel withinterlayer of 1.52 mm thick Sentry Glas (R) of DuPontmake + 12 mm Air gap + 8mm thick uncoated clear glassof same make. All glass panels shall be heat treated andheat soak tested. Refer Particular relevant technicalSpecification.

Sqm. 425

b Frameless glazing system with Laminated glass: Frameless glazing system with supplying and fixing of 19.52mm thick laminated glass having 10 mm thick as outerpanel and 8 mm thick as inner panel with interlayer of1.52 mm thick Sentry Glas (R) of DuPont make. Outerpane glass shall be Reflective coated glass on # 2 surface

Pebble Blue Grey of Asahi make or Super Silver Greenof Asahi make or ST 467 of Saint Gobain make. Innerpane shall clear glass and both panes shall heat treatedand heat soak tested. Refer Particular relevant technicalSpecification.

Sqm. 5

304 Frameless glazing system with Glass Fin:

Complete system for Frameless glazing as mentioned inParticular Specification. Rate shall include cost of spiders,Articulated bolts and supply and fixing the Glass fin withrequired size to satisfy the structural criteria and rate shallexclude the cost of Off site proto type test. The thickness

of glass fin shall be 21.52mm thick (Min) laminatedtoughened and heat soak tested as per specification.

a Frameless glazing system with Laminated DGU: Frameless glazing system with supplying and fixing of 33.52mm thick (13.52mm + 12mm Air gap + 8mm) LaminatedDouble glazed unit having 13.52 mm thick with 6mmthick Reflective low E coated Grey Lite of Asahi make or

Green Radiance of Asahi make or KT 455 Reflective

coated glass of Saint Gobain make as outer panel and 6mm thick uncoated clear glass as inner panel withinterlayer of 1.52 mm thick Sentry Glas (R) of DuPont

make + 12 mm Air gap + 8mm thick uncoated clear glassof same make. All glass panels shall be heat treated andheat soak tested. Refer Particular relevant technicalSpecification.

Sqm. 110



b Frameless glazing system with Laminated glass: Frameless glazing system with supplying and fixing of 19.52mm thick laminated glass having 10 mm thick as outerpanel and 8 mm thick as inner panel with interlayer of1.52 mm thick Sentry Glas (R) of DuPont make. Outerpane glass shall be Reflective coated glass on # 2 surface

Pebble Blue Grey of Asahi make or Super Silver Green

of Asahi make or ST 467 of Saint Gobain make. Innerpane shall clear glass and both panes shall heat treatedand heat soak tested. Refer Particular relevant technicalSpecification.

Sqm. 5

305 System for Standard Sliding Door: Providing and fixingthe Standard sliding door with ES 200 operator with ST

Flex profile with both side fixed panel of Dorma make

or EC Drive operator with ST Flex profile with both sidefixed panel of Geze make with the required structuralsupport. Rate shall include the cost for supplying andfixing 12.52 mm thick laminated glass having 6 mm thickas outer panel and 5 mm thick as inner panel with

interlayer of 1.52 mm thick Sentry Glas (R) of DuPontmake. Outer pane glass shall be reflective coated glass -Sunergy Clear of Asahi make or ST 167 of Saint Gobainmake. Inner pane shall be uncoated clear glass and bothpanes shall be heat treated and heat soaked. All MSmembers shall be painted with anti corrosive, low VOCPU paint (metallic finish) with compatible primer to aminimum film thickness of 75 microns and 2 coats of lowVOC PU paint of Akzonoble make and total dry filmthickness 225 microns. (If MS work is involved) ReferParticular relevant technical Specification.

Sqm. 13

306 Providing and fixing colour anodized aluminium PivotedDouble leaf / Single leaf door with openable side hungshutter as per drawing and fixed at all levels, elevationsand heights. Rate shall include the cost of Necessaryhardwares, accessories as given in the particularspecification and supplying and fixing og glass as givenbelow. Refer Particular relevant technical Specification.

Openable swing door with Insulated Glass - 24 mm thickwith 6 mm thick Reflective low E coated Grey Lite ofAsahi make or Green Radiance of Asahi make or KT 455Reflective coated glass of Saint Gobain make as outerpane and 12 mm airgap and 6 mm thick uncoated clearglass as inner pane of same make. Both panes are heattreated. Rate including supplying and fixing the glass.The glass will be selected at appropriate time by Engineer-Incharge.

a Single Leaf door Sqm. 10

b Double Leaf door Sqm. 20



307 Designing, providing and fixing Aluminium Twin StyleDouble leaf / Single leaf door with openable side hungshutter with Top & Bottom rails TP/TA of Dorma make

or Geze make. Rate shall include the cost for supply &fixing of hardwares like Floor spring, Handle and Locketc with necessary accessories etc and supplying & fixing12.52 mm thick laminated glass having 6 mm thick asouter panel and 5 mm thick as inner panel with interlayerof 1.52 mm thick Sentry Glas (R) of Dupont make. Outerpane glass shall be reflective coated glass -Sunergy Clearof Asahi make or ST 167 of Saint Gobain make. Inner paneshall be uncoated clear glass and both panes shall be heattreated and heat soaked. Refer particular specification fortype and make of hardwares to be considered for tenderquote. Refer Particular relevant technical Specification.

a Single Leaf door Sqm. 5

b Double Leaf door Sqm. 12

308 Providing and fixing Fixed cum Openable windows with

Aluminium anodized frames of Schuco / Kawneer makeor approved equivalent make with Specified glass belowand fabricated as per drawing and fixed at all levels. Rateshall include the cost of Necessary hardwares foropenable shutter and fixed panels, aluminium colouranodized subframe, accessories and supplying and fixingof glass. Refer Particular relevant technical Specification.

a Fixed cum Openable windows with Monolithic Glass 6mm thick Reflective coated glass on # 2 surface - Supersilver Green of Asahi make or ST 467 Saint gobain make.All panels are heat treated. Rate including supplying andfixing the glass. The glass will be selected at appropriatetime by Engineer-Incharge.

Sqm. 170

b Fixed cum Openable windows with Monolithic Glass 6mm thick Reflective coated glass on # 2 surface - PebbleBlue Grey of Asahi make or Super silver Green of Asahimake or ST 467 Saint gobain make. All panes are heattreated. Rate including supplying and fixing the glass.The glass will be selected at appropriate time by Engineer-Incharge.

Sqm. 1535

309 Providing and fixing Fixed cum Sliding windows withAluminium anodized frames of Schuco / Kawneer makeor approved equivalent make with Specified glass below

and fabricated as per drawing and fixed at all levels. Rateshall include the cost of Necessary hardwares for slidingshutter and fixed panels, aluminium colour anodizedsubframe, accessories and supplying and fixing of glass.Refer Particular relevant technical Specification.



a Fixed cum Sliding windows with Insulated Glass -24 mmthick with 6 mm thick Reflective low E coated Grey Lite ofAsahi make or Green Radiance of Asahi make or KT 455Reflective coated glass of Saint Gobain make as outerpane and 12 mm airgap and 6 mm thick uncoated clearglass as inner pane of same make. Both panes are heattreated. Rate including supplying and fixing the glass.The glass will be selected at appropriate time by Engineer-Incharge.

Sqm. 70

b Fixed cum Sliding windows with Monolithic Glass 6 mmthick Reflective coated glass on # 2 surface -Super silverGreen of Asahi make or ST 450 Saint gobain make. Allpanes are heat treated. Rate including supplying andfixing the glass. The glass will be selected at appropriatetime by Engineer-Incharge.

Sqm. 255

c Fixed cum Sliding windows with Monolithic Glass 6 mmthick Reflective coated glass on # 2 surface -Pebble BlueGrey of Asahi make or Super silver Green of Asahi makeor ST 467 Saint gobain make. All panes are heat treated.

Rate including supplying and fixing the glass. The glasswill be selected at appropriate time by Engineer-Incharge.

Sqm. 10

Laminated sandwiched composite panel cladding and

Associated works

310 Dry wall cladding : Providing and fixing the systemto clad the Laminated sandwiched compositepanel of Alucobond or Alubond or Durabuild orAludecor make with approved colour and shade (4 mm(0.5 + 3.0 + 0.5) ACP with Mineral core / polyethylene100% Virgin Core) as per the specification describedin Technical specifications, on the external surface theexternal surface like column, wall, jambs, sills, projected

area, ceiling or any surface to any profile and shape,horizontally, vertically, sloped, curved, circular etccomplete. Rate shall include the cost of supplying andfixing of Laminated sandwiched composite panel(ACP with Mineral core / polyethylene 100%virgin Core), Non staining weather for Vertical &horizontal joints in general the frame work for ACPcladding consists of aluminium box frame with 'C' cleatframe on the Box frame with HDG bracket etc, complete.All anchors, bolts and screws shall be SS 316 grade of Hilti/ Fischer make. Refer Particular relevant technicalSpecification.

Sqm. 1500



311 Canopy / Pergola cladding: Designing, Providing andfixing the system to clad the Laminated sandwichedcomposite panel of Alucobond or Alubond or Durabuildor Aludecor make with approved colour and shade (4 mm(0.5 + 3.0 + 0.5) ACP with Mineral core / polyethylene100% Virgin Core) as per the specification described inTechnical specifications for Canopy, screen wall, fin and

Pergola as per profile and shape shown in the Drawingwith necessary Hot dip Galvanized Structural steelsupport to clad the ACP and all support to be designed towithstand the Design wind pressure and the specificationspecified in Particular specifications etc complete. Mainstructural steel support will be measured under respectiveitem separately.

Rate shall include the cost of supplying and fixing ofLaminated sandwiched composite panel (ACP withMineral core / polyethylene core), Non staining weatherfor Vertical & horizontal joints in general the frame work

for ACP cladding consists of aluminium box frame with'C' cleat frame on the Box frame with HDG bracket etc,complete. All anchors, bolts and screws shall be SS 316grade of Hilti / Fischer make. Refer Particular relevanttechnical Specification. NOTE :-Main structural steel frame work for Canopy, screen wall,fin and Pergola to clad the canopy with ACP shall bemeasured under respective Items, but the aluminiumframe work and supporting bracket required for claddingshall be part of the rate quoted under this item.

Sqm. 5775

312 Providing and applying Cold Bituminous coating

(Vapour barrier) on the External wall behind Composite

panel / Granite cladding area etc. Refer Particularrelevant technical Specification.

Sqm. 1530

313 Providing and fixing aluminium extruded louver "Z"

type as described below and to be designed to with standthe design wind pressure. Refer Particular relevanttechnical Specification.

a Support system to fix the Louver:Complete systemhaving colour anodized aluminium box frame, aluminiumbase plate and aluminium angles etc.Note : Weight will beconsidered only for the assembled frame part and hencenecessary wastage shall form part of the rate quoted.

Kg 795

b Fixed Louver: Providing and fixing Storm proof louver"Z" type made out of specially extruded aluminium withanodized finish and as specified in Particularspecifications and to be fixed with pitch not less than 50mm and overlapping shall be 25 mm as minimum asshown in the drawing.

Sqm. 105



314 Providing and fixing Luxalon SL - 4 Stringer with 84R

plain Louvers panel of Hunter Douglas make or

equivalent Fameline make with Luxacote finish and thelouver system shall be designed to with stand the designwind pressure. Rate shall include louver Panel, Carrier,Carrier Splice, Panel Splice and accessories etc. ReferParticular relevant technical Specification.

Sqm. 10

315 Providing and fixing Aluminium Grille of Fameline

make with specified product code as below PVDF finishand the louver system shall be designed to with stand thedesign wind pressure with pitch not less than 75 mm asshown in the drawing. Louver thickness not less than0.8mm. Rate shall include louver Panel, aluminiumframes, aluminium end caps, aluminium brackets /clamps, SS anchors, bolts and accessories etc. ReferParticular relevant technical Specification.

a Product code 2050RT Sqm. 1600

b Product code 1050RT Sqm. 10

316 Dry wall granite cladding: Quote rate for providing andfixing Granite slab - Dry type fixing using approvedcolour granite slab (Basic cost of Granite not less thanRs.140/- per sq.ft) cladding the external surface on anysurface to any profile and shape, horizontally, vertically,sloped, curved, circular etc with approved shade ofGranite thickness not less than 25 mm thick and as per thesizes shown in the Drawing etc complete and as directed.(On the Facade areas). Granite shall be fixed with agroove of 6mm and to be filled with weather sealantrecessed by 2mm. Refer Particular relevant technicalSpecification.

a Projection in line with Façade finishes as per drawing. Sqm. 30

b Projection upto 75 mm from the Main base structure. Sqm. 10

317 Providing dadoing with machine cut and machine highPre-polished best quality granite tile of approved colourand shade with thickness not less than 12 mm of size600x300 mm, set in C.M. 1:3 of 20mm thick, includingpointing with matching cement and fixing with stainlesssteel clamps with suitable size at two ends to right angleby using SS anchor fastners and SS pin, the former withhorizontal position to be embedded in brick wall/concretesurface and the later with vertical position to be insertedand caulked in to the holes of the slab, drilled for thepurpose, both forming 'T' shape and cement groutedincluding edge polishing wherever required and forminggroove at joints as directed at all levels. Rate shall includefor preparation of base surface, SS clamps, SS anchorfastner, cleaning, chamfering, edge polishing, acid washand protection etc. complete, as directed.

Sqm. 10



318 Supplying and fixing of 16mm thick Multi wall insulatedpolycarbonate sheet roof cladding on the Structural steelframe structure at all levels as per pattern for sky LightRoof including single skin - 10 mm thick insulated polycarbonate sheet capping & specials with necessaryaluminium extrusion, cutting, fabricating, erection at alllevels as specified in the particular specification. Rateshall include the cost of all materials involved in this itemlike poly carbonate sheet and accessories etc. Rate shallexclude the cost of base M.S structural base supports shallbe measured separately under respective item specifiedabove. Refer Particular relevant technicalSpecification.Note : Surface area will be measured andpaid for.

Sqm. 395

319 Providing and fixing 3M tape (Code No: 4412NTranslucent white) of approved type and pattern withminimum 50 mm wide in addition to the Sealant at thedesired location. 3M Tape shall be provided as permanufacturer specification and methodology.

Rmt 100

320 Providing and applying over the granite / stone surfaceone coat of environment friendly silicon based WaterRepellent as per manufacturers specification with noundulations and waviness as per the specification asdirected by Engineer-Incharge.

Sqm. 50

Total of External Facade and Associated Works

Facade Access System

321 Operating System

Design, supply, install and commission Facade Accesssystem with the following equipments to make sure thatthe entire facade will be cleaned with the proposedsystem and to reach any shape and profile and the systemshall with stand a minimum design wind pressure of 200Kg/sqm conforming to IS 875-Part 3 and Lateral forces asper IS 1893 (Latest Revision) and the system support atparapet wall as specified.Bidderr shall be responsible todetermine the maximum design wind pressure and lateralforces, moments, stresses etc. applicable for the system.Negative / suction pressures if determined as per IS 875 -part - 3 and Lateral forces as per code IS 1893 shall makeallowances as described in the code for corner effects onthe system. Quoted rate shall include the following, butnot limited to

a) Designing the system, preparation of shop drawing forapproval, supply, fabricate, erect as per approveddrawing at all levels, elevation & heights includingconducting necessary test according to the codes etccom lete.b) In general, system comprising, Traverse Trolley(Permanent) system with two manual gondola and whichshall suspend Standard 2 Metre long cradle withImported wire ropes and winches.



c) Supply & Install the necessary supporting brackets withSS anchor bolts,etc complete.d) All support system necessary for installation includingscaffolding, hoists, minor civil works and any other worksequipment related thereto for complete installation of thesystem as per specification and approved shop Drawing.

e) Supply and anchoring the Soffit / Face mountedbrackets at a minimum spacing specified elsewhere in thestraight / curved portion and extra bracket if anyrequired at corners / projected area shall be providedwith hot dip galvanized steel anchor bolt assemblies withbase Plates.f) Providing and anchoring brackets with suitable dia ofHilti make Anchor bolts permanently on the wall ceilingas specified in the approved shop drawing.g) Obtain & submit certification of design by independentprofessional engineer / consultant along with final designand shop drawings. h) Manufacture / fabrication,transport and handling, installation / fixing, testing,

commissioning and Insurance. i) Taxes, Duties, levies andimparting training to owners representatives in operationand maintenance of the system.

j) Rate shall included for maintenance of the all systems asspecified in the conditions of contract during the defectsliability period.k) Rate shall deemed to be included the above stipulatedprovision.

a Hot dip galvanized Parapet mounted combination bracket(Upper and Lower Brackets) of suitable size and Long andto be fixed at a required spacing as per design withsuitable dia & type of SS 316 grade anchor fasteners at

specified locations including grouting the surface with allother accessories etc complete.

No. 20

b Hot dip galvanized Hot rolled sections"I"Beam of 200 x100 mm or suitable size (Size given is indicative and thebidder shall confirm the size of member based onstructural requirements) and to be fixed on the Upper andLower brackets with suitable dia & type of SS 316 gradebolts at specified locations including grouting the surfacewith all other accessories etc complete.

RMT 50

c Aluminium Swivel traverse trolley (Permanent) and to befixed on the Upper and Lower Beams to manually operate

the system at specified locations with all other accessoriesetc complete. (Each set containing 2 Arm)

Set 4

322 Accessible System

Providing and fixing of Cradle platform with completesystem, the type and capacity given below and in generalthe cradle made out Aluminium tubes with Frame workand in accordance with the technical specification anddrawing.



a Standard - 2 Metre Cradle platform with all otheraccessories etc complete.

No. 1

b Providing and fixing Imported Aerial work platform withcomplete system and the working height of 21 M andabove and in accordance with the technical specificationand drawing.

No. 1

c Providing and fixing Imported Electro Hydraulic elevatedVertical platform with complete system and the workingheight of 16M and above and in accordance with thetechnical specification and drawing.

No. 2

Total of 'Facade Access System

ELECTRICAL WORKS

SECTION-A: TRANSFORMERS AND HT BREAKERS

All installation works should be as complete and as


The rate includes necessary connected minor civil works

if required and necessary supports as required at site.

No extra payment will be made for the same.

Ring Main Switichgear (Indoor) - 11KV

323 Design, Supply, Installation, Testing and Commissioningof INDOOR Weather & Dust proof Type, floor mounting,free standing 11kV Ring Main Gear unit made out of M.Ssheet steel clad dust and vermin proof with 630A CopperBusbars, Interconnections, necessary protections,Measuring Instruments, Indicating Instruments,Protection Relays, CTs, PT with necessary controlfuses/MCBs, Termination arrangements for Incomingand Outgoing Cable of 11 kV 3Core 185 Sq mm XLPEAlu.Armoured earthed cable, Terminal Blocks,

Earthing,Powder coated painting, Sign writing and Basechannels etc., with complete all accessories as required forsatisfactory operations and as per the detailed TechnicalSpecifications enclosed and as per EB Requirementscomprising of the following.

INCOMER (2 Sources) :

11kV, 630A, 500MVA LOAD Break Switch (Air Break )with necessary required accessories -2NosOUTGOING :

11kV, 630A, 500MVA VACCUM Circuit Breaker withnecessary required accessories : 1No

The RMG panel shall be manufactured as required by theelectrical authorities and approval shall be obtainedincluding testing & commissioning and any additionalfeatures required by the supply authorities shall becarried out at no extra cost.

No. 1



324 Design, supply, installation, testing and commissioning of11KV 630A, 500MVA, 26.2kA VCB Breaker HT indoorthree Panel Board with all accessories and allmetreingprotection for satisfactory operation and as required bythe statutory Electrical authorities as per the detailedspecification enclosed.

No. 1

325 Design, supply, installation, testing and commissioning of1250KVA, 11kV/433V outdoor, Oil cooled Transformer

with on load tap changer & RTCC panel as per thedetailed specification enclosed. Transformer Protectionrelays should be provided at each Transformer such asTransformer Buchholz relay, restricted earth faultrelay,OLTC surge relay, Oil temperature relay, windingtemp relay, Auxiliary relays as per standards. Thetransformer shall be provided with cable termination boxon HT side to terminate 3 core 185 Sqmm XLPE cableandsuitable for terminating air insulated aluminium busducton LT side 2000A Amps rating all as per the detailedspecification enclosed. (THE TRANSFORMER SHALL

BE SUPPLIED WITH FIRST FILL OF OIL)

Nos. 2

326 Design, supply, laying, testing and commissioning of 3

core 185 sqmm 11KV, XLPE Aluminium conductor

individual core screened, flat steel strip armoured, PVC

sheathed cable inside the building in the preparedtrench/under ground (from 11KV RMG to outdoor HTVCB panel, HT indoor VCB panel & Transformer)

RMT 100

HT Terminations:

327 Design, supply, termination, testing and commissioning

of OUTDOOR type termination kit and accessoriessuitable for 11KV, 3 core 185 Sqmm XLPE cable.

No. 1

328 Design, supply, termination, testing and commissioningof INDOOR type termination kit and accessories suitablefor 11KV, 3 core 185 Sqmm XLPE cable.

No. 6

329 Design, supply, erection, testing and commissioning of2000 Amps outdoor type air insulated Aluminium FP

busduct with flexible joints at every 4.5Mtr. Interval(RYBN) and with suitable support from ceiling as per thedetailed specification enclosed. The busduct should be

with straight run, 90 deg. Horizontal and vertical bends.(The busduct shall be Aluminium busbars of suitable size.The busbar should be support by epoxy insulators atregular intervals) The busduct shall run from Transformersecondary and DG to MPCC. The bus duct shall befabricated as per the detailed specification enclosed.Current Density of busbars shall not exceed 0.8 Amps/

Sq.mm.

RMT 60



330 Design, supply, erection, testing and commissioning of2000 Amps indoor type air insulated Aluminium FP

busduct with flexible joints at every 4.5Mtr. Interval(RYBN) and with suitable support from ceiling as per thedetailed specification enclosed. The busduct should bewith straight run, 90 deg. Horizontal and vertical bends.(The busduct shall be Aluminium busbars of suitable size.The busbar should be support by epoxy insulators atregular intervals) The busduct shall run from Transformersecondary and DG to MPCC. The bus duct shall befabricated as per the detailed specification enclosed.Current Density of busbars shall not exceed 0.8 Amps/

Sq.mm.

RMT 66

331 Design, supply, erection, testing and commissioning of1250 Amps indoor type air insulated Aluminium FP

busduct with flexible joints at every 4.5Mtr. Interval(RYBN) and with suitable support from ceiling as per thedetailed specification enclosed. The busduct should bewith straight run, 90 deg. Horizontal and vertical bends.

(The busduct shall be Aluminium busbars of suitable size.The busbar should be support by epoxy insulators atregular intervals) The busduct shall run from MPCC toCapacitor Panel. The bus duct shall be fabricated as perthe detailed specification enclosed. Current Density of

busbars shall not exceed 0.8 Amps/ Sq.mm.

RMT 24

332 Design, supply, erection, testing and commissioning ofBattery Charger 110V DC 100 AH Trip unit combinedwith trickle & boost charge facilities with batterybank(SMF) & Distribuition Board and as per the detailed

specification / drawing enclosed.

No. 1

333 Removing the existing indoor HT RMG Panel (630A LBSas incomer and 630A VCB as outgoing) and existing HTCables and handing over to customer

No. 1

334 Removing the existing indoor HT Panel (630A VCB asincomer and 630A LBS-2Nos as outgoings) and existingHT Cables and handing over to customer

No. 1

335 Removing the existing Transformer and HT Cables andhanding over to customer

Nos. 1

336 Removing the existing LT Main Panel and incoming LTCable and handing over to customer

Nos. 1

337 Removing the existing Emergency LT Panel and incomingLT Cable and handing over to customer

Nos. 1

338 Removing & re-laying the existing LT cables withterminations from LT Main Panel & Emergency LT Panel(12 runs of cables, 1R-3.5Cx240, 7R-3.5Cx185, 2R-4Cx16,2R-3.5Cx35), 10mtr length (approx)

LS 1

339 Removing the existing capacitor bank and LT Cable andhanding over to customer

Nos. 1

SECTION – B : LT PANEL BOARDS








Note: All themetres Should be provided with RS 485

BMS integration. All themetres should be connected in

series thro' bus cable terminated at commonmetre

chamber340 Design, supply, erection, testing and

commissioning of cubicle type floor mounting mainpower control centre made out of MS sheet enclosurewith Aluminium busbars, single busbar system, cablechamber, interconnection, painting, earthing, protectionrelays etc. comprising of the following : (MPCC)

INCOMING

EB Incomer

2 Nos. 2000 Amps 4 Pole 65KA electrical draw out typeAir circuit breaker with shunt release shutter assembly,

door interlock and all other accessories.Instruments Panel

Digital type Ammeter & Voltmeter, Maximum demandcontroller, Instantaneous earthfault relay (2 O/C+ 1 E/F),Low set earth fault relay (51G), CTs control fuses, RYBIndication lamps and “ON/OFF/Trip" indicating lamp ineach incomer, and also refer the drawing. The rate shall beinclusive of neutral CT connected with E/F Relay & spaceHeater

DG Incomer

2 Nos. 2000 Amps 4 Pole 65KA electrical draw out typeAir circuit breaker with shunt release shutter assembly,door interlock and all other accessories.Instruments Panel

Digital type Multifunctionmetre, CTs control fuses, RYBIndication lamps and “ON/OFF/Trip" indicating lamp ineach incomer, and also refer the drawing.

Buscoupler

1No.2000 Amps 4 pole 65KA electrical draw out type Aircircuit breaker with shunt release, shutter assembly, doorinterlock and all other required necessary accessories andON/OFF lamps.The buscoupler shall be provided with mechanical &

electrical Inetrlocking arrangements.OUTGOINGS

1250A 4P MDO ACB, 50 KA – 4Nos

800A 4P MCCB, 50 KA – 4Nos





All the Outgoing feeder should be ON/OFF/Tripindication lamps, Digital type Multifuctionmetre(Exceptcapacitor feeder which is provided with Ammeter),CTs,Fuse, Switch control,Front operting handles etc. Allswitch boards shall be fabricated as per the detailedspecification enclosed. Suitable size outgoing cablechamber and extra busbars should be provided forconnecting the number of outgoing cables as per theschematic drawing. Additional NO + NC contact shouldbe provided for BMS monitoring. All the NO+NC contactwiring should be terminated on commonmetre chamber.The board shall be fabricated for future extension of thepanel board.

The transformers incomer shall be provided withprotection relays such as IDMT (2 O/C +1 E/F),Maximum demand controller, REFR (Restricted Earthfault Relay),etc., and bus coupler shall be both mechanicaland electrical interlocking arrangements by hardwarecontrol wiring alongwith PLC (Programmable Logic

Controls). The Hardware control wiring & PLC operationshall be feasible to extend for future Transformer if anyand all as per the detailed specification and drawingsenclosed. -This incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc.Incomingmetre for Transformer shall be with demandcontroller , Harmonic THD and individual harmonicdisplay+ Regular parameters like V, I, KVA, KVAR, KW,KWH, KVARh, PF, Freq, Max, AVGIncomingmetre for Generator shall be with Loadmonitoring without demand control and with regular

parameter & Harmonics THD & Individual harmonicdisplayAll Outgoing Feeders in Main panel shall be with MFMmonitoring V,I, KWH, KVARH, PF with RS 485 BMSintegration. All themetres to be connected in series thro'bus cable terminated at commonmetre chamber

Main Power Control Centre (MPCC)

2000Amps 4P Aluminium busbars:- All the neutral

busbars shall have the same capacity of phase

busbars.(0.8A/Sq. mm.)

No. 1

341 Design, supply, fixing, testing and commissioning of

cubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (APFCR Panel)

Incoming

1250A TP MDO ACB 50 KA Drawout type with Autopower factor correction relay with necessary CT, controlwiring etc.- 1 No. as incomer.Outgoing: Total 425 KVAR



2 sets of 100 KVAR (4 x 25 KVAR) with 400A TP MCCB35KA, suitable contactors with switching steps in therating of 100 KVAR as required.3 sets of 50 KVAR (2 x 25 KVAR) with 200A TP MCCB25KA, suitable contactors with switching steps in therating of 50 KVAR as required.3 sets of 25 KVAR (1 x 25 KVAR) with 100A TP MCCB16KA, suitable contactors with switching steps in therating of 25 KVAR as required.Each All KVAR capacitor bank in a separate compartmentwith necessary ventilation arrangemnts or weld mesharrangements as required by the Electrical Authorities .

With necessary Aluminium busbars, interconnections,providing Ammeter with selector switches, phaseindication lamp, control fuse and switch control, PFmetreetc. with RS 485 BMS integration as per the specification.

Capacitor Panel - 425 kVAR

1250 Amps TPN Aluminium busbars:- All the neutral

busbars shall have half the capacity of phase busbars(0.8A/Sq. mm)

Nos. 2

342 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (Utility Panel)

INCOMING

250A 4P MCCB 25 KA with connected accessories –

2Nos.as incomer with 2 lock and 1 key mechanicalinterlock arrangementOUTGOINGS

63A TPN MCCB, 16 KA – 3Nos

32A TPN MCCB, 16 KA – 5NosWith necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration250A Amps 4P Aluminium busbars : All the neutral

busbars shall have the same capacity of phase busbars

(0.8A/Sq. mm.)

No. 1

343 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. SUB SWITCH BOARD-1

(OFFICE AREA)

INCOMING

1250A TP&N MDO ACB 50 KA Drawout type withconnected accessories – 1No.as incomer

OUTGOINGS




630A TPN MCCB, 35 KA – 1No



With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer the

drawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration1250A Amps TPN Aluminium busbars : All the neutral

busbars shall have half the capacity of phase busbars

(0.8A/Sq. mm.).

No. 1

344 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. SUB SWITCH BOARD-2

(OFFICE AREA)

INCOMING

1250A TP&N MDO ACB 50 KA Drawout type withconnected accessories – 1No.as incomerOUTGOINGS





With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,

Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration1250A Amps TPN Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

345 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per the

detailed specification enclosed. LIGHTING POWERSWITCH BOARD -REGIONAL STORE

INCOMING


1No.as incomerOUTGOINGS





With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

346 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. LIGHTING POWER

SWITCH BOARD -RECREATIONAL BLOCK

INCOMING





With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,

KVARH, PF with RS 485 BMS integration125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

347 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. POWER PANEL -

RECREATIONAL BLOCK

INCOMING

250A TPN MCCB 25 KA with connected accessories –

1No.as incomer

OUTGOINGS125A TPN MCCB, 25 KA – 2Nos

63A TPN MCCB, 16 KA – 1No.


With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.



The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration250A Amps TPN Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

348 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (LPSB-1) LIGHTING

POWER SWITCH BOARD - TYPE-C&D

INCOMING



63A TPN MCCB, 16 KA + KWHmetre – 2Nos

32A TPN MCCB, 16 KA + KWHmetre – 2NosWith necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration100A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

349 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (LPSB-2,8,14 &18)

LIGHTING POWER SWITCH BOARD - TYPE-C&D

INCOMING





With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration



125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

Nos. 4

350 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (LPSB-3, 4 to 7, 9 to 13 &

15 to 17) LIGHTING POWER SWITCH BOARD - TYPE-C&D

INCOMING






The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS inte ration125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

Nos 13

351 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. LIFT PANEL - TYPE-

C&D + BACHELOR & TRANSIT

INCOMING



32A TPN MCCB, 16 KA + KWHmetre – 6 Nos

With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,short

circuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

Nos. 2




POWER SWITCH BOARD - BACHELOR & TRANSIT

INCOMING

100A 4P MCCB 16 KA with connected accessories –1No.as incomerOUTGOINGS



With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS inte ration100A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

353 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (LPSB-3 to 12)

LIGHTING POWER SWITCH BOARD - BACHELOR &

TRANSIT

INCOMING





100A Amps 4P Aluminium busbars : All the neutralbusbars shall have the same capacity of phase busbars

(0.8A/Sq. mm.).

Nos 10


POWER SWITCH BOARD - TYPE-C&D



INCOMING




With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,

Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration100A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

355 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per the

detailed specification enclosed. (LSB-1) LIGHTING

SWITCH BOARD -(OFFICE AREA)

INCOMING




With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall be

Microprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH,PF with RS 485 BMS integration100A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 4

356 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (PSB-1) POWER

SWITCH BOARD -1 (OFFICE AREA)INCOMING









(0.8A/Sq. mm.).

No. 1


SWITCH BOARD -2 (OFFICE AREA)

INCOMING






630A Amps 4P Aluminium busbars : All the neutralbusbars shall have the same capacity of phase busbars

(0.8A/Sq. mm.).

No. 1



INCOMING



100A TPN MCCB, 16 KA – 1No.63A TPN MCCB, 16 KA – 11Nos





The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration400A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1



INCOMING







(0.8A/Sq. mm.).

No. 1

360 Design, supply, fixing, testing and commissioning of

cubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. LIFT PANEL - OFFICE

AREA

INCOMING





With necessary Aluminium busbars, interconnections,

providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration



125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1

361 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (UPS O/G PANEL) UPS

O/G PANEL -OFFICE AREAINCOMING

630A TP+2N MCCB 35 KA with connected accessories –

2 Nos as incomerOUTGOINGS


2 Nos as incomerWith necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration630A Amps TP+2N Aluminium busbars (0.8A/Sq. mm.). Nos. 1

362 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (AC PANEL ) OFFICE

AREA

INCOMING


1 No.as incomerOUTGOINGS

100A TPN MCCB, 16 KA – 1No.



With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shall

be with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration125A Amps 4P Aluminium busbars : All the neutral


(0.8A/Sq. mm.).

No. 1



363 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (EMERGENCY

LIGHTING PANEL ) -OFFICE AREA

INCOMING




With necessary Aluminium busbars, interconnections,providing , ON,OFF,TRIP, phase indication lamp, Fuse,Switch control etc.in the incomer and also refer thedrawing.The incoming and outgoing breakers shall beMicroprocessor based release such as overload,shortcircuit,earth fault,neutral protection,etc. The incomer shallbe with Mutlifunctionmetre monitoring V, I, KWH,KVARH, PF with RS 485 BMS integration100A Amps TP+2N Aluminium busbars : All the neutral

busbars shall have the same capacity of phase busbars(0.8A/Sq. mm.).

No. 1

364 Design, supply, fixing, testing and commissioning ofcubicle type floor mounting switch board comprising ofthe following, the board shall be fabricated as per thedetailed specification enclosed. (SSB) -SUBSWITCH

BOARD FOR EXISTING RESIDENCE

INCOMING

800A TP+N MCCB 25 KA with connected accessories –






800A Amps TP+N Aluminium busbars : All the neutralbusbars shall have half the capacity of phase busbars

(0.8A/Sq. mm.).

No. 1

365 SUPPLY, FIXING, TESTING AND COMMISSIONING OFTHE SURGE & TRANSIENT PROTECTION ANDCONNECTED WORKS WITH ALL NECESSARY FIXINGACCESSORIES ETC COMPLETE AS PER STANDARSAND AS REQUIRED AT SITE SIMILAR TO THEFOLLOWINGS:



a Supply of Class B Surge protection device to be installedbetween L-N and N-PE as per the followingspecifications: (PROTECTION PROVISION FOR MPCCINCOMER AT INCOMING SIDE)

Nos. 2

Surge Suppressor system shall consist of Single Spark GapClass I as per IEC and Class B as per VDE standards,capable of carrying 50 KA,10/350microsec lightning surgebetween phase to neutral ( 3 Nos for R, Y & B) & 100 KA,10/350 microsecond neutral to earth (1 no for N-PE)having maximum protection <0.9 KV between phase &neutral and < 1.5 KV between neutral and earth. SurgeProtection devices shall be suitable for operation on 415 V,50 Hz, 3 phase, 4 wire AC supply in TT configurationcomplying with IEC 61024, IEC 61312 and VDE 0100-534and tested as per IEC 61643 and VDE 0675 standards.Itshall be installed at the input of LT Main panel and themounting shall be on 35 mm DIN rail

OBO Model : 3 nos. – Line to Neutral : MCD 50 - B 1no. –

Neutral to Earth : MCD125-B + NPEb Supply of co-ordinated surge protection to be installed

between L-N and N-PE as per the following

specifications (FOR ALL SUBPANEL INCOMER SIDE)

Nos 55

Surge Suppressor system shall consist of Single SparkGap, Class I as per IEC and Class B as per VDE standards,capable of carrying 50 KA at 10/350 microsec lightningsurge between phase to neutral & MOV type category IIas per IEC and Class C as per VDE Standards: Pluggabledevice should be capable of carrying 20 KA,8/20microsecond surges between phase to neutral and havingprotection 1.6 KV between phase to neutral and 100 KA at10/350 microsecond between neutral to earth with amaximum protection of < 1.5 KV between neutral to earth.Surge Protection devices shall be suitable for operation on415 V, 50 Hz, 3 phase, 4/3 wire AC supply in TTconfiguration complying with IEC 61024, IEC 61312 andVDE 0100-534 and tested as per IEC 61643 and VDE 0675standards.

OBO Model : V25 – B+C/3 +NPE

c Supply of Class C type Surge Protection Device

connection between Phase to Neutral & between

Neutral to Earth for Sub distribution system as per the

following specifications (FOR ALL UPS RELATEDDISTRIBUTION BOARDS)

Nos. 8



Surge Suppressor MOV type category II as per IEC andClass C as per VDE Standards: Pluggable device shouldbe capable of carrying 20 KA,8/20 microsecond surgesbetween phase to neutral as well as neutral to earth,having protection 1.6 KV between phase to neutral at <1.0 KV between neutral to Earth including wiring remoteindication at all the three phases and visual indication fordefects at R, Y, B and Neutral. It shall be installed at theinput of Sub Distribution panel and the mounting shall beon 35 mm DIN rail. Surge Protection devices shall besuitable for operation on 415 V, 50 Hz, 3 phase, 4 wire ACsupply in TT configuration complying with IEC 61024,IEC 61312 and VDE 0100-534 and tested as per IEC 61643and VDE 0675 standards

OBO Model : V20-C/3+NPESECTION – C : DISTRIBUTION BOARDS




if required and necessary supports as required at site.No extra payment will be made for the same.

366 LPDB / LDB / ELDB :-

LOC: OFFICE AREA + RECREATIONAL BLOCK +

REGIONAL STORE + BACHELOR & TRANSIT + TYPE

C&D + Sub station

Supply, fixing, testing and commissioning of the double

door type compartmental 4way MCCB DB comprising ofthe following :32A 4P MCCB 16KA – 1 No. as incomer.

25A DP MCB with 25A DP ELCB 30mA – 3 Nos. asoutgoings.Each 25A DP MCB outgoing consist of 4nos.16/20A 10KA SPMCB in a separate compartment with necessaryphase segregation as required by the ElectricalInspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos 61

367 LPDB / LDB :-

LOC: OFFICE AREA + REGIONAL STORE +BACHELOR & TRANSIT



25A DP MCB with 25A DP ELCB 30mA – 3 Nos. asoutgoings.



Each 25A DP MCB outgoing consist of 6nos.6/10/16/20A, 10 KA SP MCB in a separate compartmentwith necessary phase segregation as required by theElectrical Inspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 6

368 LPDB / LDB :-

LOC: OFFICE AREA + BACHELOR & TRANSIT



40A DP MCB with 40A DP ELCB 30mA – 3 Nos. asoutgoings.Each 40A DP MCB outgoing consist of 8nos.6/10/16/20A 10 KA SPMCB in a separate compartment

with necessary phase segregation as required by theElectrical Inspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos 72

369 VTPN DB (AC DB)/ PDB: OFFICE AREA


door type VTPN 8way MCCB DB comprising of thefollowing :

100A TPN MCCB 16KA with ELR and all other requiredaccessories – 1 No. as incomer.

32A TP MCB 10KA – 8 Nos. as outgoings.

With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 2

370 AC DB / VENTILATION DB (7 segment DB) - 6 WAY

LOC: OFFICE + REGIONAL STORE


door type compartmental Phase segregated 6way MCCBDB comprising of the following :

63A TPN MCCB – 1No. as incomer.

40A DP MCB 10KA (C-Curve) with 40A DP ELCB 100mA– 3 Nos. as outgoings.

Each 40A DP MCB outgoing consist of 6nos.16/20A 10KASPMCB (C-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.




Nos. 7

371 AC DB / VENTILATION DB (7 segment DB) - 4 WAY

LOC: OFFICE + RECREATIONAL BLOCK


door type compartmental Phase segregated 4way MCCB

DB comprising of the following :



Each 40A DP MCB outgoing consist of 4nos.16/20A 10KASPMCB (C-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.With necessary tinned copper busbars, interconnections,

separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 2

372 UPS DB (7 segment DB) - 6 WAY

LOC: OFFICE AREA




63A TPN MCCB – 1 No. as incomer.

40A DP RCBO Type: Hpi-A with 10KA & 30mA – 3 Nos.

as outgoings.Each 40A DP RCBO outgoing consist of 6nos.16/20A,10KA SPMCB (D-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 3

373 UPS DB (7 segment DB) - 4 WAY

LOC: OFFICE + RECREATIONAL BLOCK




32A TPN MCCB – 1 No. as incomer.

25A DP RCBO Type: Hpi-A with 10KA & 30mA – 3 Nos.as outgoings.



Each 25A DP RCBO outgoing consist of 4nos.16/20A,10KA SPMCB (D-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 4

374 UPS DB (VTPN DB) - 8 WAY

LOC: OFFICE AREA


door type VTPN 8way MCCB DB comprising of thefollowing :100A TPN MCCB 16KA with ELR and all other requiredaccessories – 1 No. as incomer.


With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.

The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 1

375 PDB/LDB (7 segment DB) - 12 WAY

LOC: OFFICE AREA + RECREATIONAL BLOCK


door type compartmental Phase segregated 12way

MCCB DB comprising of the following :



Each 63A DP MCB outgoing consist of 12nos.6/10/16/20A 10KA SPMCB (C-Curve) in a separatecompartment with necessary phase segregation asrequired by the Electrical Inspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

Nos. 3

376 PDB (7 segment DB) - 8 WAY

LOC: OFFICE AREA + RECREATIONAL BLOCK






Each 40A DP MCB outgoing consist of 8nos. 16/20A10KA SPMCB (C-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.




Nos. 8


LOC: REGIONAL STORE






Each 40A DP MCB outgoing consist of 6nos.6/10/16/20A10KA SPMCB (C-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.


No. 1


LOC: REGIONAL STORE + TYPE C&D + Sub station





40A DP MCB 10KA (C-Curve) with 40A DP ELCB 100mA

– 3 Nos. as outgoings.Each 40A DP MCB outgoing consist of 4nos. 16/20A10KA SPMCB (C-Curve) in a separate compartment withnecessary phase segregation as required by the ElectricalInspectorate.With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.The board shall be powder coated type fixed withconcealed system in wall. The rate shall include necessaryconnected civil works like chipping, rough plastering etc.

No. 3

379 PDB (VTPN DB) - 12 WAY

LOC: OFFICE AREA


door type VTPN 12way MCCB DB comprising ofthe following :125A TPN MCCB 16KA with ELR and all other requiredaccessories – 1 No. as incomer.





Nos. 1

380 PDB (VTPN DB) - 4 WAY

LOC: REGIONAL STORE


door type VTPN 4way MCCB DB comprising of thefollowing :63A TPN MCCB 16KA with ELR and all other requiredaccessories – 1 No. as incomer.



Nos. 1

381 ELDB (SPN DB) - 12 WAYLOC: OFFICE AREA + BACHELOR & TRANSIT +

TYPE-C&D


door type 12way SPN DB comprising of the following :

32A DP MCB with 32A dp ELCB 30 mA – 1 No. asincomer.6/10A SP MCB 10KA (C-Curve) – 6 Nos. as outgoings.

With necessary tinned copper busbars, interconnections,separate earth bus, separate neutral bus for each phases.


Nos 37

382 EXTERNAL LDB (FEEDER PILLAR BOX)


door type VTPN 4 way MCCB DB comprising of thefollowing :32A 4P MCCB 16KA with 32A 4P Timer & Contactor –

1No. as incomer16A TP MCB 10KA – 4Nos. as outgoings.

With necessary tinned copper busbars, interconnections,earth bus, neutral bus. The board shall be powder coatedtype fixed with concealed system in wall. The rate shallinclude necessary connected civil works like chipping,rough plastering etc.

Nos. 4

SECTION – D : ALUMINIUM CONDUCTOR

COMPACT AIR INSULATED BUSDUCT & TAP-OFF

BOXES








383 200A Aluminium conductor Compact Air insulated

Design Rising Main

a Supply, Installation, Testing and Commissioning of

TP+2N, 4Wire, 200A Aluminium conductor Air insulatedDesign Rising Mains with 15 X 3 (2) External Copperearthing, Plug in Point at every 500mm, Fire Barriers atevery Floor Crossing : Indoor : 30kA (Busbar Size 20mm X6mm (1 Runs))Enclosure is 1.6mm GI; Insulation is ClassFThe product shall be based on Temp. rise & not oncurrent density

RMT 30

b 200A End Feed Unit with 25kA TP+2N MCCB Nos. 2

c End Covers Nos. 2

d Mounting Brackets (Recommended 1No. per 1.5 Mtrs) Nos 20

e 100A Tap Off Box with 16kA TP+2N MCCB Nos. 1

f 63A Tap Off Box with 16kA TP+2N MCCB Nos. 6

384 400A Aluminium conductor Compact Air insulatedDesign Rising Main

a Supply, Installation, Testing and Commissioning of 4P,4Wire, 400A Aluminium conductor Air insulated DesignRising Mains with 25 X 3 (2) External Copper earthing,Plug in Point at every 500mm, Fire Barriers at every FloorCrossing : Indoor : 30kA (Busbar Size 50mm X 6mm (1Runs)) Enclosure is 1.6mm GI; Insulation is Class F Theproduct shall be based on Temp. rise & not on currentdensit

RMT 21

b 400A End Feed Unit with 35kA 4P MCCB Nos. 1

c End Covers Nos. 1

d Mounting Brackets (Recommended 1No. per 1.5 Mtrs) Nos 14e 100A Tap Off Box with 16kA 4P MCCB Nos. 5


Design Rising Main

a Supply, Installation, Testing and Commissioning of 4P,4Wire, 630A Aluminium conductor Air insulated DesignRising Mains with 25 X 3 (2) External Copper earthing,Plug in Point at every 500mm, Fire Barriers at every FloorCrossing : Indoor : 50kA (Busbar Size 90mm X 6mm (1Runs)) Enclosure is 1.6mm GI; Insulation is Class F Theproduct shall be based on Temp. rise & not on currentdensity

RMT 36

b 630A End Feed Unit with 50kA 4P MCCB Nos. 1

c End Covers Nos. 1

d Mounting Barckets (Recommended 1 per 1.5 Mtrs) Nos 24

e 100A Tap Off Box with 16kA 4P MCCB Nos 14


Design Rising Main



a Supply, Installation, Testing and Commissioning ofTP+N, 4Wire, 800A Aluminium conductor Air insulatedDesign Rising Mains with 25 X 3 (2) External Copperearthing, Plug in Point at every 500mm, Fire Barriers atevery Floor Crossing : Indoor : 50kA (Busbar Size 50mm X6mm (2 Runs))Enclosure is 1.6mm GI; Insulation is ClassFThe product shall be based on Temp. rise & not oncurrent density

RMT 114

b 800A End Feed Unit with 50kA 4P MCCB Nos. 4c End Covers Nos. 4

d Mounting Barckets (Recommended 1 per 1.5 Mtrs) Nos 76

e 630A Tap Off Box with 35kA 4P MCCB Nos. 1

f 400A Tap Off Box with 35kA 4P MCCB Nos. 1

g 200A Tap Off Box with 25kA 4P MCCB Nos. 1

h 125A Tap Off Box with 25kA 4P MCCB Nos 21

i 100A Tap Off Box with 16kA 4P MCCB Nos. 2SECTION – E : WIRING AND CONNECTED

ACCESSORIES


directed by Engineer-Incharge.The rate includes necessary connected minor civil works



387 Wiring to the Circuit mains (DB to switch board / firstpoint of light fitting) (avg. length - 40 Mtrs)using 2 Runsof 2.5 and 1 Run of 1.5sqmm multi strand PVC insulatedcopper conductor (FRLS) in 25mm dia. MS pipe in opensystem in above false ceiling and concealed system inbelow false ceiling, all complete complying with relevantstandard specifications

Pts. 110

388 Wiring to the Circuit mains (DB to switch board / firstpoint) (avg. length - 40 Mtrs)using 2 Runs of 2.5 and 1Run of 1.5sqmm multi strand PVC insulated copperconductor (FRLS) in existing MS pipe in open system inabove false ceiling and concealed system in below falseceiling, all complete complying with relevant standardspecifications

Pts. 90

389 Wiring to the light points/ 6A plug point using 2 Runs of2.5 and 1 Run of 1.5sqmm for primary point (switch tofirst point) and 3 Runs of 1.5 Sqmm for secondary point)(looping), multi strand PVC insulated copper conductor(FRLS) in suitable size MS pipe in open system in abovefalse ceiling and concealed system in below false ceiling.

The primary point rate should inclusive of supply andfixing of 6A modular type switch in a suitable sizemodular box in concealed system,the secondary point rateshould inclusive of supply, laying of GI flexible hose forlighting drops from ceiling, all complete complying withrelevant standard specifications

a Primary point Pts. 650

b Secondary point Pts. 850



390 Wiring to the lift well light and power points using 2 Runsof 2.5 sqmm and 1 Run of 1.5 sqmm multi strand PVCinsulated copper conductor (FRLS),separate circuit (fromDB) shall be laid for power points in suitable size MS pipein open system.The rate should inclusive of supply andfixing of 1 No. of 6A switch for control the light and 1 No.6A socket controlled by 6A modular type switch in asuitable size modular box with face plate and all othernecessary accessories.

Pts. 78

391 Wiring to the 6/16A 5Pin or 6Amps Raw power / UPS

socket using 3C X 2.5 sqmm copper flexible cable (FRLS)in existing raceway / conduits (under floor) with all othernecessary accessories.

RMT 4800


socket and also wiring to IBMS systems using 2 Runs of2.5 sqmm and 1Run of 1.5 sqmm multi strand PVCinsulated copper conductor (FRLS) in 25mm dia. MS pipein open system above false ceiling and concealed systemin below false ceiling in wall / column etc.

RMT 4700


socket using 2 Runs of 2.5 sqmm and 1Run of 1.5 sqmmmulti strand PVC insulated copper conductor (FRLS) inexisting MS pipe in open system above false ceiling andconcealed system in below false ceiling in wall / columnetc.

RMT 300

394 Wiring to the 6/16A 5Pin Raw power / UPS socket using3C X 4 sqmm copper flexible cable (FRLS) in existingraceway / conduits (under floor) with all other necessaryaccessories.

RMT 2900

395 Wiring to the power plugs using 2 Runs of 4 sq.mm and 1

Run of 2.5 sqmm multi strand PVC insulated copperconductor (FRLS) in a suitable size MS pipe in opensystem at above false ceiling and concealed system inbelow false ceiling in wall / column etc. (For Airconditioner)

RMT 2100

LOC : Type C&D + Regional store

396 Wiring to the Circuit mains (DB to switch board / firstpoint of light fitting) (avg. length - 18Mtrs)using 2 Runs of2.5 and 1 Run of 1.5sqmm multi strand PVC insulatedcopper conductor (FRLS) in suitable size PVC HMS pipein open system in above false ceiling and concealedsystem in below false ceiling, all complete complying withrelevant standard specifications

Pts. 500



397 Wiring to the light/fan points, primary & secondary point(switch to first point and looping) using 3 Runs of 1.5Sqmm multi strand PVC insulated copper conductor(FRLS) in suitable size PVC HMS pipe in open system inabove false ceiling and concealed system in below falseceiling. The primary point rate should inclusive of supplyand fixing of 6A modular type switch in a suitable sizemodular box in concealed system, all complete complyingwith relevant standard specifications

a Primary point Pts. 3195

b Secondary point Pts. 1232

398 Wiring to the 6/16A 5 pin or 6 amps Raw power / UPS

socket using 2 Runs of 2.5 sqmm and 1Run of 1.5 sqmmmulti strand PVC insulated copper conductor (FRLS) in25mm dia. PVC HMS pipe in open system above falseceiling and concealed system in below false ceiling in wall/ column etc.

RMT 9500

399 Wiring to the 6/16A 5 pin or 6 amps Raw power / UPS

socket using 2 Runs of 2.5 sqmm and 1Run of 1.5 sqmm

multi strand PVC insulated copper conductor (FRLS) inexisting PVC HMS pipe in open system above false ceilingand concealed system in below false ceiling in wall /column etc.

RMT 4700

400 Wiring to the power plugs using 2 Runs of 4 sq.mm and 1Run of 2.5 sqmm multi strand PVC insulated copperconductor (FRLS) in a suitable size PVC HMS pipe inopen system at above false ceiling and concealed systemin below false ceiling in wall / column etc. (For Airconditioner)

RMT 11000

401 Supply, fixing, testing and commissioning of 2Nos. 6/10 /13A modular type Universal socket for UPS Power

supply and switch combination in a suitable size modularbox in recessed system. (2Nos.6/10/13A modular socketcontrolled by 2Nos.16A Switches)

Nos. 176

402 Supply, fixing, testing and commissioning of 1No. 6/16Amodular type socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem. (1No.6/16A modular socket controlled by1No.16A Switch)

Nos. 460

403 Supply, fixing, testing and commissioning of 1No. 6/16Amodular type socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem. (1No.6/16A modular socket controlled by1No.16A Switch). Similar to Legrand Myrius

Nos 275

404 Supply, fixing, testing and commissioning of 1No. 6/16Amodular type socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem. (1No.6/16A modular socket controlled by1No.16A Switch). Similar to Legrand Arteor

Nos 10



405 Supply, fixing, testing and commissioning of 1No. 16Amodular type socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem. (1No.16A modular socket controlled by 1No.16ASwitch)

Nos. 55

406 Supply, fixing, testing and commissioning of 1No.6Amodular socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem.(1No.6A modular socket controlled by 1No.6Aswitch)

Nos. 404

407 Supply, fixing, testing and commissioning of 1No. 6Amodular type socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem. (1No.6A modular socket controlled by 1No.6ASwitch). Similar to Legrand Myrius

Nos 1912

408 Supply, fixing, testing and commissioning of 1No. 6Amodular type socket for Raw Power supply and switchcombination in a suitable size modular box in recessedsystem. (1No.6A modular socket controlled by 1No.6ASwitch). Similar to Legrand Arteor

Nos 82

409 Supply, fixing, testing and commissioning of 1No.6Amodular socket for Raw Power supply in a suitable sizemodular box in recessed system.(1No.6A modular typesocket ) (For exhaust fan point) Similar to Legrand Myrius

Nos. 250

410 Supply, fixing, testing and commissioning of 1No.16Amodular socket for Raw Power supply in a suitable sizemodular box in recessed system.(1No.16A modular typesocket ) (For Gyser ) Similar to Legrand Myrius

Nos. 177

411 Design, supply,fixing, testing and commissioning of 20A3 pin metal clad socket controlled by 20A DP MCB in a

suitable size MS enclosure fixed in open system. (For Airconditioner)

Nos. 478

412 Design, supply,fixing, testing and commissioning of 32A5 pin metal clad socket controlled by 32A 4P MCB in asuitable size MS enclosure fixed in open system.

Nos. 22

413 Design, supply, fixing, testing and commissioning of 20A,5 pin metal clad socket controlled by 20A 4P MCB in asuitable size MS enclosure fixed in open system. ( For ACsystem)

Nos. 9

414 Design, supply,fixing, testing and commissioning of 16A,3 pin polycorbonite socket controlled by 16A DP MCB in asuitable size weatherproof enclosure fixed in open system.

Nos. 20

415 Design, supply, fixing, testing and commissioning of 32A4P MCB in a suitable size weatherproof enclosure fixed inopen system.

Nos. 22

416 Design, supply, fixing, testing and commissioning of 63ATPN MCCB in a suitable size weatherproof enclosurefixed in open system.

Nos. 9

417 Design, supply, fixing, testing and commissioning of125A TPN MCCB in a suitable size weatherproofenclosure fixed in open system.

Nos. 1



418 Design, supply, fixing, testing and commissioning of 63ATPN MCCB in a suitable size MS enclosure fixed in opensystem.

Nos. 3

419 Design, supply, fixing, testing and commissioning of125A TPN MCCB in a suitable size MS enclosure fixed inopen system.

Nos. 5

420 Supply and fixing of suitable size metal box to fix the RJ45Data socket. The rate shall include the wall cutting,chipping and rough finishing etc.,

Nos. 10

421 Supply, fixing, testing and commissioning of RJ45 Datasocket with suitable modular plate and metal box.. Similarto Legrand Myrius

Nos. 4

422 Supply, fixing, testing and commissioning of RJ45 Datasocket with suitable modular plate and metal box.. Similarto Legrand Arteor

Nos. 4

423 Supply and fixing of suitable size metal box to fix the RJ11Telephone socket. The rate shall include the wall cutting,chipping and rough finishing etc.,

Nos. 10

424 Supply, fixing, testing and commissioning of RJ11Telephone socket with suitable modular plate and metal

box. Similar to Legrand Myrius

Nos 406

425 Supply, fixing, testing and commissioning of RJ11Telephone socket with suitable modular plate and metalbox. Similar to Legrand Arteor

Nos 18

426 Supply, fixing, testing and commissioning of TV socketwith suitable modular plate and metal box.

Nos. 75

427 Supply, fixing, testing and commissioning of TV socketwith suitable modular plate and metal box. Similar toLegrand Myrius

Nos 169

428 Supply, fixing, testing and commissioning of TV socketwith suitable modular plate and metal box. Similar toLegrand Arteor

Nos. 8

429 supply, fixing, testing and commissioning of 1 No. of 6A 1

way modular switch in a suitable size face plate withmetal box and all other necessary accessories.

Nos. 10

430 supply, fixing, testing and commissioning of 1 No. of 6A2way modular switch in a suitable size face plate withmetal box and all other necessary accessories. Similar toLegrand Myrius

Nos. 564

431 supply, fixing, testing and commissioning of 1 No. of 6A2way modular switch in a suitable size face plate withmetal box and all other necessary accessories. Similarto Legrand Arteor

Nos. 35

432 supply, fixing, testing and commissioning of 1 No. of 16Amodular switch in a suitable size face plate with metal boxand all other necessary accessories. Similar to Legrand

Myrius

Nos. 190

433 supply, fixing, testing and commissioning of 1 No. ofelectronic regulator in a suitable size face plate with metalbox and all other necessary accessories. Similar toLegrand Myrius

Nos 546

434 supply, fixing, testing and commissioning of 1 No. ofelectronic regulator in a suitable size face plate with metalbox and all other necessary accessories. Similar toLegrand Arteor

Nos 26



435 Supply, fixing, testing and commissioning of Calling bell/Buzzer with push type switch and Buzzer / Bell. Similarto Legrand Myrius

Nos 105

436 Supply, fixing, testing and commissioning of Calling bell/Buzzer with push type switch and Buzzer / Bell.Similar to Legrand Arteor

Nos. 6

437 Supply and fixing of fan hook with all other necessaryaccessories.

Nos 572

438 Supply and laying of following size PVC / MS conduits infloor / wall /ceiling etc. including necessarybends,elbow,etc, in concealed system below the falseceiling on wall/floor and open system on above falseceiling. FOR ELECTRICAL, DG, IBMS , DATA &TELEPHONE SYSTEMS)The rate shall includes minor civil works such aschipping, plastering and to make good finished surface tomatch with the original surface.

a 20mm dia MS conduit. RMT 100

b 25mm dia MS Conduit RMT 3800

c 32mm dia MS Conduit RMT 50

d 50mm dia MS Conduit RMT 50e 20mm dia PVC HMS Conduit RMT 100

f 25mm dia PVC HMS Conduit RMT 100

g 32mm dia PVC HMS Conduit RMT 700

h 50mm dia PVC HMS Conduit RMT 100

439 Supply and installation of under floor pregalvanised sheetsteel channel (raceways) as per the detailed specificationas below:

a Supply, fixing of the 100 x 38 X 1.6mm pregalvanisedsheet steel Channel (Raceways) including stiffner atrequired intervals in recessed system in floor includingcutting chippling, plastering in the floor/wall to make

good finish to match with the floor /wall etc. (Similar toMK list No. - UMDX 100/1/6)

RMT 340

b Joint Sleeve for UMDX 100/1/6 Nos 136

c Supply, fixing of the 150 x 38 X 1.6mm pregalvanisedsheet steel Channel (Raceways) including stiffner atrequired intervals in recessed system in floor includingcutting chippling, plastering in the floor/wall to makegood finish to match with the floor /wall etc. (Similar toMK list no. - UMDX 150/2/6)

RMT 120

d Joint Sleeve for UMDX 150/1/6 Nos 48

e Supply, fixing of the 300 x 38 X 1.6mm pregalvanisedsheet steel Channel (Raceways) including stiffner atrequired intervals in recessed system in floor includingcutting chippling, plastering in the floor/wall to makegood finish to match with the floor /wall etc. (Similar toMK list no. - UMDX 300/3/6)

RMT 200

f Joint Sleeve for UMDX 300/1/6 Nos 80



g Supply, fixing of the 50 x 25 X 1.6mm pregalvanised sheetsteel Channel (Raceways) including stiffner at requiredintervals in recessed system in floor including cuttingchippling, plastering in the floor/wall to make goodfinish to match with the floor /wall etc. (Similar to MK listno. - UMDX 50/1/6)

RMT 75

h Joint Sleeve for UMDX 50/1/6 Nos 30

i Supply, fixing of the 100 x 25 X 1.6mm pregalvanisedsheet steel Channel (Raceways) including stiffner atrequired intervals in recessed system in floor includingcutting chippling, plastering in the floor/wall to makegood finish to match with the floor /wall etc. (Similar toMK list no. - UMDX 100/1/6)

RMT 25

j Joint Sleeve for UMDX 100/1/6 Nos 10

440 Supply, fixing, testing of under floor access outlet box /Floor junction box / crossover junction box as per thedetailed specification as below:The rate shall includes cutting the existing floor with use

of cutting machine and chipping the cement mortar andthe debris shall be removed from the site. After fixing thetrunking the floor shall be plastered to match the originalsurface.Floor access outlet boxes

Supply of MK access outlet boxes, manufactured fromhigh-pressure die cast material with trap frame & trapmade of flame retardant Engineering Plastic . ABS.Patented screwless polyamide ratchets are provided forself adjusting of the floor box for any floor finishes. Trapcover is reinforced with a 2.5mm thick pre-galvanizedsteel plate with a recess of 8mm for accommodating theflooring.The trap cover is provided with ElectrostaticPolyester Epoxy Coating, to prevent rust accumulation.

The system has provision to accommodate threecompartment trunking to run Mains Voltage & Extra LowVoltage cables. The system has Positive Double EarthingConnections to ensure safety.The system also has theprovision to accommodate 25/38mm deep trunking witha Knockout of 65,100,150,200,225mm. Load bearingCapacity: 2 tons; Dimensions: 250*250mm similar to MKList No.ESB 250/3/1 in the Existing floor with concealedsystem. Combination of switch & sockets will be decidedat the time of execution

Nos. 1

441 Floor Junction Boxes without flyover

Supply and fixing of Junction boxes manufactured fromhigh-pressure die cast material. The Trap Cover & Trapframe of the box should be made of 2.5mm thick pre-galvanized steel plate made of Electrostatic Polyesterepoxy coating. The recess should be 8mm on the trap lidto accommodate the specified flooring.



The junction boxes should have the provision to route anddistribute either the power or networking cables. Thesystem must have smooth curved die cast pillars for easeof pulling cables. The system must have the provision toaccommodate 25/38mm deep and upto 225mm wide GItrunking. similar to MK List No.JB 150 / 250 / 300 / 350 /400Height adjustment: The system must have the stainlesssteel leveling screws; Load bearing Capacity: 3.6 tons onthe trap lid; Standards: The system must comply with therelevant specification & IEC 61084

a JB 150 Nos 60

b JB 250 Nos 25

c JB 300 Nos 25

d JB 350 Nos 40

e JB 400 Nos 20

442 Cross Over Junction Boxes without flyover

Supply and fixing of Junction boxes manufactured fromhigh-pressure die cast material. The Trap Cover & Trap

frame of the box should be made of 2.5mm thick pre-galvanized steel plate made of Electrostatic Polyesterepoxy coating. The recess should be 8mm on the trap lidto accommodate the specified flooring.The cross over boxes should have flyover units made ofABS plastic or metal to route and distribute power, dataand voice cables. The system must have smooth curveddie cast pillars for ease of pulling cables. The system musthave the provision to accommodate 25/38mm deep andupto 225mm wide GI trunking. similar to MK List No.EJB250 / 300 / 350 / 400Height adjustment: The system must have the stainless

steel leveling screws; Load bearing Capacity: 3.6 to 4.8tons on the trap lid; Standards: The system must complywith the relevant specification & IEC 61084

a EJB 250 Nos. 5

b EJB 300 Nos. 2

c EJB 350 Nos. 5

d EJB 400 Nos. 1

443 Telephone and lan cabling

a Supplying, fixing, connecting and commissioning ofreputed Brand 10Pair Krone Connector Type Telephone

Tag Block in 16G Thick sheet steel enclosure at each flatfixed flush with the wall.

Nos. 32

b Supplying, fixing, connecting and commissioning 20 PairKRONE CONNECTOR TYPE Telephone Tag Block - Sub

Tag Block in 14 G Thick sheet steel enclosure at EachFloor.

Nos. 32

c Supplying,fixing,connecting and commissioning 200 PairKRONE CONNECTOR TYPE Telephone Tag Block -

Main Tag Block in 14 G Thick sheet steel enclosure atGround Floor

Nos. 4



d Supplying, laying, connecting & commissioning ofreputed brand 3 Pair un armoured with colour coded 0.5Sq.mm. annealed copper conductor Telephone cable in

already laid PVC Conduits/ raceways concealed in floor/ Ceiling /wall with necessary clamps,screws etc from 5pair Krone Connector to each telephone points.

RMT 5500

e Supplying, laying, connecting & commissioning ofreputed brand 10Pair un armoured with colour coded 0.5Sq.mm. annealed copper conductor Telephone cable in

already laid PVC Conduits / raceways concealed in floor/ Ceiling / wall with necessary clamps, screws etc.

RMT 1500

f Supplying, laying and concealing of PVC pipe of 25mm

dia with necessary specials and other materialsincluding Run off 1 No. Fish wire (G.I. 22g) for drawingcable for Telephone / data etc., all complete and as perspecifications

RMT 2500

g Supplying, laying, connecting & commissioning 20 pair

un armoured with colour coded 0.5 Sq.mm annealedcopper conductor Telephone cable in already laid PVC

Conduits concealed in floor / Ceiling /wall withnecessary clamps, screws etc from Man Tag block atGround floor to Sub Tag block at each floor

RMT 1500

444 TV CABLING

a Supplying, connecting and commissioning of reputedbrand RG 6 Trunk Co-axial cable in already laid PVC

Conduits concealed in wall / ceiling / floors withnecessary clamps, screws etc.

RMT 7000

b Supplying, fixing, connecting and commissioning of

6Way Splitter at Each Flat

Nos. 40

c Supplying, laying and concealing of PVC pipe of 25mm

dia with necessary specials and other materialsincluding Run off 1 No. Fish wire (G.I. 22g) for drawingcable for T.V. etc., all complete and as per specifications

RMT 2500

SECTION – F : POWER AND CONTROL CABLES /

TERMINATIONS:








445 Supply, laying of following size XLPE / PVC (FRLS)insulated armoured cables with aluminium / copperconductors partly laid in existing cable tray and partlylaid in wall/ ceiling with suitbale clamps for workingvoltages up to and including 1100V conforming to IS 1554part I 1988 for PVC and IS 7098 Part I for XLPE. Cable traywill be measured and paid separately. FORELECTRICAL, DG, IBMS , FPS & HVAC SYSTEMS)

a 3.5 Core 400 Sq.mm XLPE Aluminium armoured Cable RMT 2830

b 3.5 Core 300 Sq.mm XLPE Aluminium armoured Cable RMT 400

c 3.5 Core 240 Sq.mm XLPE Aluminium armoured Cable RMT 900

e 3.5 Core 150 Sq.mm XLPE Aluminium armoured Cable RMT 55

f 3.5 Core 120 Sq.mm XLPE Aluminium armoured Cable RMT 32

i 3.5 Core 50 Sq.mm XLPE Aluminium armoured Cable RMT 2700

j 3.5 Core 35 Sq.mm XLPE Aluminium armoured Cable RMT 750k 4 Core 25 Sq.mm XLPE Aluminium armoured Cable RMT 2900

l 4 Core 16 Sq.mm XLPE Aluminium armoured Cable RMT 3800

n 4 Core 6 Sq.mm PVC Copper armoured Cable (FRLS) RMT 3200

o 3 Core 4 Sq.mm PVC Copper armoured Cable (FRLS) RMT 95

p 3 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) RMT 7900

s 1 Core 150 Sq.mm PVC Copper Unarmoured Cable(FRLS)

RMT 440

t 1 Core 70 Sq.mm PVC Copper Unarmoured Cable (FRLS) RMT 650

u 1 Core 35 Sq.mm PVC Copper Unarmoured Cable (FRLS) RMT 900

v 1 Core 25 Sq.mm PVC Copper Unarmoured Cable (FRLS) RMT 230

w 1 Core 16 Sq.mm PVC Copper Unarmoured Cable (FRLS) RMT 20

x 1 Core 10 Sq.mm PVC Copper Unarmoured Cable (FRLS) RMT 330

z 24 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) RMT 100

aa 12 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) RMT 100

ab 7 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) RMT 50

ac 4 Core 4 Sq.mm PVC Copper armoured Cable (FRLS) RMT 2500446 Supply and termination of the following size cables with

suitable double compression glands with suitablecrimping socket. (copper sockets for copper cables andAlu. Sockets for alum. Cable) FOR ELECTRICAL, DG,IBMS , FPS & HVAC SYSTEMS)

a 3.5 Core 400 Sq.mm XLPE Aluminium armoured Cable Nos. 36

b 3.5 Core 300 Sq.mm XLPE Aluminium armoured Cable Nos. 4



c 3.5 Core 240 Sq.mm XLPE Aluminium armoured Cable Nos. 26

d 3.5 Core 150 Sq.mm XLPE Aluminium armoured Cable Nos. 4

e 3.5 Core 120 Sq.mm XLPE Aluminium armoured Cable Nos. 4

f 3.5 Core 50 Sq.mm XLPE Aluminium armoured Cable Nos. 58

g 3.5 Core 35 Sq.mm XLPE Aluminium armoured Cable Nos. 56

h 4 Core 25 Sq.mm XLPE Aluminium armoured Cable Nos. 222

i 4 Core 16 Sq.mm PVC Aluminium armoured Cable(FRLS)

Nos. 244

j 4 Core 6 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 66

k 3 Core 4 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 2

l 3 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 132

m 1 Core 150 Sq.mm PVC Copper Unarmoured Cable(FRLS)

Nos. 80

n 1 Core 70 Sq.mm PVC Copper Unarmoured Cable (FRLS) Nos. 20

o 1 Core 35 Sq.mm PVC Copper Unarmoured Cable (FRLS) Nos. 44

p 1 Core 25 Sq.mm PVC Copper Unarmoured Cable (FRLS) Nos. 16

q 1 Core 16 Sq.mm PVC Copper Unarmoured Cable (FRLS) Nos. 4

r 1 Core 10 Sq.mm PVC Copper Unarmoured Cable (FRLS) Nos. 32

s 24 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 4

t 12 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 4

u 7 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 4

v 4 Core 4 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 80

w 4 Core 2.5 Sq.mm PVC Copper armoured Cable (FRLS) Nos. 27

SECTION – G : Earthing system ( FOR ELECTRICAL,

DG, IBMS , FPS & HVAC SYSTEMS)








447 Supply and installation of earth pipe electrode as per IS3043 complete with 3mtr long with 40mm dia 'B' class G.I.pipe and GI earth plate of size 600mm x 600mm x 6mmincluding 2 runs of 50 x 6mm GI flat upto test link fromplate earth electrode, watering funnel and necessary bolt,nut and double washer. Including 750mm x 750mm x3mtr long excavation and construction of 850mm x850mm x 300 mm high brick wall chamber with cementmortor. The chamber shall be provided with 450mm x450mm x 10mm cast iron / RCC cover with frame andlockable facility. The plate electrode shall be filled withalternate layer of salt and charcoal as required full depth.The Cover shall be heavy duty to suit heavy vehiclemovements

Nos 24

448 Supply and installation of earth pipe electrode as per IS3043 complete with 3 mtr long with 40mm dia 'B' class G.I.pipe and copper earth plate of size 600mm x 600mm x3mm including 2 runs of 25 x 6mm CU. flat upto test linkfrom plate earth electrode, watering funnel and necessarybolt, nut and double washer. Including 750mm x 750mm

x 3mtr long excavation and construction of 850mm x850mm x 300 mm high brick wall chamber with cementmortor. The chamber shall be provided with 450mm x450mm x 10mm cast iron / RCC cover with frame andlockable facility. The plate electrode shall be filled withalternate layer of salt and charcoal as required full depth.The Cover shall be heavy duty to suit heavy vehiclemovements

Nos 36

449 Supply and laying of 50 x 6 mm G.I flat RMT 370

450 Supply and laying of 25 x 6 mm G.I flat RMT 350

451 Supply and laying of 25 x 3 mm Cu flat RMT 340

452 Supply and laying of 8 gauge bare copper wire RMT 2580

453 Supply and laying of 50 x 10 mm copper flat for Neutral RMT 150

454 Supply, erection of following sizes GI ladder / perforatedtype cable rack system made out of sheet steel folded torequired shape with adequate number of supports. ( FORELECTRICAL, DG, IBMS , FPS & HVAC SYSTEMS)

The cable rack shall have runners rugs of suitable size,horizontal elbow, vertical elbow 90 Deg. Up verticalelbow 90 Deg. Down, re-deep, coupler plates, materials.The cable racks shall be suspended from ceilingsupported from side walls in columns etc. with adequatesize supporting angles / channels with fastners, welding,

anchor bolts, nuts etc. The rack shall have suitable cableclamping arrangements etc. complete with all civil worksfor fabrication details. Refer enclosed drawing.



The rate shall be inclusive of suitable hanging support -gripple make cable with crimp arrangement supports,spacing and fixing as per standards. The height of thehanging arrangement shall be as per drawing and with allaccesories to fix the hangers at purlin, rafter beam withrequired clamps nuts & bolts to be considered.

Perforated type

a 300mm x 75mm x 2.0mm RMT 400

b 450mm x 75mm x 2.0mm RMT 350Ladder type

c 450mm x 75mm x 2.0mm RMT 900

d 600mm x 75mm x 2.0mm RMT 50

e 750mm x 75mm x 2.0mm RMT 800

f 1000mm x 75mm x 2.5mm RMT 60

455 Sheet steel of 14G for connecting the tray. Sqm. 70

456 25 x 6 mm copper Earth busbar - 1 mtr long withnecessary insulator supports

Nos 10

SECTION – H : SAFETY EQUIPMENTS

All installation works should be as complete and asdirected by Engineer-Incharge.




457 Supply and laying of class B, 2.5mm thickness 1M X 2Mwide chequered rubber mat with dielectric strength of45KV suitable for 11KV installation as per IS 15625 / 2006

Nos. 3

458 Supply and laying of class 2, 3mm thickness 1M X 2Mwide chequered rubber mat suitable for 440V installation

as per IEC 61111

Nos 25

459 Supply and fixing of HT/LT cable route indicator madeout of MS flat and angle iron. The cable route marker shallbe fixed at both the ends of cable at joints at 50Mtrs.Spacing for straight runs.

Nos 200

460 Supply and providing shock treatment chart in English,Hindi and Tamil duly framed with 2mm thick glass infront & 6mm thick ply on back as required

Nos 10

461 Supply and fixing of GI fire buckets with round bottom,each set comprising 4Nos.fire buckets of 9Kg capacityincluding supply of M.S pedestal stand with hookssuitable for holding of 4Nos of fire buckets, painted with

Post Office Red oil paint and letter FIRE on each bucketand filling with sand complete as required. .

Nos 10

462 Supply of tested hand gloves of 11KV grade. Nos. 2

463 Supply and providing St. John make first aid box 18SWGMS sheet duly painted as approved by Indian red crosssoceity complete with all first aid medicines.

Nos. 6



464 Supply & Fixing HT danger notice plate 250mm x 200mmmade of MS steel 2mm thick & Vitreous enameled whiteon both sides and with inscriptions in signal Red on frontside as required by the electrical authorities.

Nos. 2

465 Supply & Fixing LT danger notice plate 200mm x 150mmmade of MS steel 2mm thick & Vitreous enameled whiteon both sides and with inscriptions in signal Red on frontside as required

Nos. 6

466 Supply & Fixing of Artificial Respirator forInspiration with chart showing the use of it.

Nos 10

467 Supply & Fixing of MS sheet board of size 500mm x300mm of 16 SWG with Entry Restricted To Authorised

Persons Only near the Main entrance of the Substation.The lettering shall be Black painted on Yellow Background.

Nos 10

SECTION – I: EXTERNAL WORKS




if required and necessary supports as required at site.No extra payment will be made for the same.

468 Supply & laying of 40 mm dia. GI pipe for cable entry inthe pole foundation

RMT 170

469 Design, supply & laying of the 8 SWG bare copper wirefor earthing.

RMT 350

470 Supply and Installation of 20mm dia., 1.5mtr long GIearthing spike for street light pole earthing

Nos 92

471 Similar to SCHREDER-Teceo 1 Glass Extra Clear Flat

Smooth 27W LED

Teceo 1 luminaire made up of Die cast aluminium alloy

body should be of IP66 Tightness level for both the opticalcompartment and the control gear compartment.The LEDchip should be arranged on a stainless steel plate andshould be sealed with a extra clear toughned glass for aoptimal luminous flux and ensuring a tightness level ofIP66 for the optical compartment. LensoFlex2®:Photometric engine specifically dedicated to offeringphotometric flexibility and performance.Leds in Neutralwhite (4100K) should be equpped with Special developedlenses for proper road lighting photometry. Future Proof:The optical unit should be easily removed and replaced atthe real site at the end of the service life in order to takethe advantage of the future technological developments.THermix ®:Large surface area for better heatmanagement.



The LED engine should contain 16 nos of LED with 1.2 Weach LED.The luminaire should be protected agaisntsurge up to 10 KV.The optical compartmnet and theelectronic compartment should be separate compartmentsfor heat management.The electrical connections should beautomatically cutoff while opening the control gearcompartment.The luminaire should be provided withuniversal mounting clamp which also allows theluminaire to change the inclination as required at site.Allthe wires used inside the luminaire should be of siliconwires and all the screws used should be of stainless steel.

The LED engine should contain 16 nos of LED driven at acurrent of 500mA to give an total wattage of around 41W.System luminous flux < 4176 lumens; Burning life : 90%output at 60,000 burning hrs and 70% output at 1Lburning hrs; Colour tempearture: 4100K; CRI > 65;

Nos 92

LED :Rebel-ES NW 174lm@500mA

472 Similar to KESELEC SCHREDER CONICAL POLE GI

OF6 MTR HT.The column should be made up of hot dipped galvanizediron which should be bended and tapered towards thetop. The total height of the pole should be 6200 mm andthe lighting luminaire should be mounted at a height of6000 mm.The column should be given with two coats ofepoxy primer and above that it should be given withpolyeruthane UV resistantt coating.The column shall alsobe provided with flush door at the bottom with properstrengthening to the cutout of the door opening. A junction/ looping box with Heavy duty 3 phase connectorshall be built into the pole. COLOR - As per standardshade card.

Nos 92

473 Similar to Keselec Schreder Neos3/IB/250W/1312 /IP66

The floddlight luminaire with a tightness level of IP66suitable for 250W Metal halide .The body should consistof two parts made of painted,die cast aluminiumalloy.The body contains a reflector made of polioshed andanodized aluminium and a removable control gear plate.The protector is made of hardened glass .It is sealed tothe cover with a silicone gasket.The luminaire should behaving a powder coating finish.The Impact resistance ofthe glass should be IK08 Electrical insulation class should

be I or II in accordance with standard EN 60598.All thecables used inside the luminaire should be silicon cableswhich is fire resisitant.The empty weight of the fixtureshould be around 8 Kg.A mounting bracket has to beprovided inorder to adjust the flood light luminaire as perthe required angle.Lamp Color:830

Nos 30

Lamps: 1 x 250W MHL



474 Similar to Keselec Schreder Corus/IB/70W/1602/CDMT

.Lamp Color Code:830

Corus Consisting of painted die-cast aluminium alloybody and hardened glass protector sealed onto the bodyby means of a silicone gasket.The floodlight is closed atone end by a painted,die cast aluminium alloy cover,andat the other end,by a frame and door assembly also made

of painted,die cast aluminium alloy.The reflector made ofpolished and anodised aluminium and the control gearare removable. Suitable for 70W CDMT Lamp.

Nos 10

Lamps: 1 x 70W CDMT

475 Similar to KESELEC SCHREDER ZIA LED

TILTABLE/24 DEG/1216MM/70WLED /IP67/Blue

• Illumination in continuous lines • Continuous lineswith an easy & invisible in-out system • Variousinstallation possibilities: fixed or adjustable on-site •

Linear floodlight 400mm lengths . Numerous symmetricallight distributions • Monochromatic or RGB versions •

Static or dynamic versions • Sturdy mechanical

conception: aluminium, fiber-glass reinforced polyester &glass • IP 67 tightness level • Optimized thermaldissipation

Nos 42

Lamps: 70W LED

476 Similar to Keselec Schreder

Corus/IB/70W/1639M/CDMT .Lamp Color Code:830

Corus Consisting of painted die-cast aluminium alloybody and hardened glass protector sealed onto the bodyby means of a silicone gasket.The floodlight is closed atone end by a painted,die cast aluminium alloy cover,andat the other end,by a frame and door assembly also madeof painted,die cast aluminium alloy.The reflector made of

polished and anodised aluminium and the control gearare removable. Suitable for 70W CDMT Lamp. Color PureWhite

Nos 4

Lamps: 1 x 70W CDMT


FOCAL/CMHB/150W/1576/IP66/830

FOCAL Floodlight (IP66)consisting of a painted ,die castaluminium alloy body and cover.The body contains thecontrol gear plate and the lamp holder support with a fineadjustment screws for the fine adjustment of the focusingof the lamp when switched on.The optical compartmentconsists of hardened glass sealed onto the body and areflector made of deep drawn,polished and anodisedaluminium.suiable for 150W CDMT lamp.All the cablesused inside the luminaire should be silicon cables which isfire resisitant.It should be provided with a mountingclamp which enables the mounting of the luminaire at 3mtr ht on th facade of the building.

Nos. 4

Lamps: 1 x 150W CDMT

RECREATIONAL BLOCK





Corus Consisting of painted die-cast aluminium alloybody and hardened glass protector sealed onto the bodyby means of a silicone gasket.The floodlight is closed atone end by a painted,die cast aluminium alloy cover,andat the other end,by a frame and door assembly also made

of painted,die cast aluminium alloy.The reflector made ofpolished and anodised aluminium and the control gearare removable. Suitable for 35W CDMT Lamp. Color PureWhite

Nos 10

Lamps: 1 x 35W CDMT

479 Similar to Keselec Schreder Enyo 3 LED Static Version

Warm white

Schreder Enyo:Hyper-compact spotlight • Numeroussymmetrical light distributions • It should be of Static(mono) with 3 High power LEDs of 1.2W • Sturdymechanical conception: aluminium, stainless steel & glassshule be made up of aluminim,Glass and Stainless steel •

IP 67 tightness level • Optimized thermal dissipation

Nos 32



Corus Consisting of painted die-cast aluminium alloybody and hardened glass protector sealed onto the bodyby means of a silicone gasket.The floodlight is closed atone end by a painted,die cast aluminium alloy cover,andat the other end,by a frame and door assembly also madeof painted,die cast aluminium alloy.The reflector made ofpolished and anodised aluminium and the control gearare removable. Suitable for 35W CDMT Lamp. Color PureWhite

Nos 10

Lamps: 1 x 35W CDMT481 Similar to Keselec Schreder

FOCAL/CMHB/150W/1576/IP66/942

FOCAL Floodlight (IP66)consisting of a painted ,die castaluminium alloy body and cover.The body contains thecontrol gear plate and the lamp holder support with a fineadjustment screws for the fine adjustment of the focusingof the lamp when switched on.The optical compartmentconsists of hardened glass sealed onto the body and areflector made of deep drawn,polished and anodisedaluminium.suiable for 150W CDMT lamp.All the cablesused inside the luminaire should be silicon cables which isfire resisitant.It should be provided with a mountingclamp which enables the mounting of the luminaire at 3mtr ht on th facade of the building.

Nos. 2

Lamps: 1 x 150W CDMT

482 Similar to Keselec Schreder Terra Maxi/IB/150W/1453M

with Kit Lamo Color Code:830



Embedded flood light (IP 67) - a pressure die castaluminium alloy body and cover – cover attached to thebody with 4 nos. stainless steel rapid closing mechanisms;toughened 19mm thick glass protector capable ofwithstanding load of 3 tons; a double gasket recessed intothe body, removable control gear tray, pre-wired with 2.5sq mm, 3 core copper flexible cable 1.5m long with spunand anodised aluminium reflector and suitable for 150WCDMT lamps

Nos. 6

Lamps: 150W CDMT

483 Similar to Keselec Schreder Corus/IB/70W/1602/CDMT

.Lamp Color Code:942

Corus Consisting of painted die-cast aluminium alloybody and hardened glass protector sealed onto the bodyby means of a silicone gasket.The floodlight is closed atone end by a painted,die cast aluminium alloy cover,andat the other end,by a frame and door assembly also madeof painted,die cast aluminium alloy.The reflector made ofpolished and anodised aluminium and the control gearare removable. Suitable for 35W CDMT Lamp. Color Pure

White

Nos 6

Lamps: 1 x 35W CDMT

SECTION – J : UPS SYSTEM & CONNECTED WORKS






Supply, fixing, Testing and commissioning of the

following UPS System and connected works with all

necessary accessories complete as required at site and asper standards.



484 Supply, Installation Testing and Commissioning of MicroProcessor Controlled 1 x 70 KVA UPS input supply of 415Volts + 15%, 3 Phase, 50 Hz ± 10% and an out put of 415Volts ±1%, 3 Phase 50 ± 0.1 Hz, Input Power Factor<=0.99, Input Total Harmonic Distortion (THDi) <2.5%,Unity Output Power Factor @ 35deg C consisting ofRectifier, Inverter, External Isolation Transformer, BatteryDC Circuit Breaker with necessary MS enclosure, InbuiltStatic BY PASS Panel (Input & output switches and AutoStatic & Manual Bypass Switches), necessary cable alleyshall be provided if cable entry/exit for UPS unit is frombottom/sides and necessary hardware & software forBMS Intergration with communication port RS 485 (Status Monitoring ), all interconnecting Copper cables(Battery bank to Battery DC Circuit breaker, Battery DCCircuit breaker to UPS, complete as required) withnecessary adequate size of copper lugs etc., withnecessary base channels/supports complete as requiredand all other necessary accessories required as perdetailed specification.

No. 2

485 Supply, Installation, Testing and Commissioning ofSealed Maintenance Free Batteries to support 70KVA for20 minutes complete with intercell connectors & coppercables, battery stand made out of Powder Coated MSAngles with adequate supports to carry the load of thebatteries.

No. 2

486 Supply, Installation Testing and Commissioning of MicroProcessor Controlled 1 x 60 KVA UPS input supply of 415Volts + 15%, 3 Phase, 50 Hz ± 10% and an out put of 415Volts ±1%, 3 Phase 50 ± 0.1 Hz, Input Power Factor<=0.99, Input Total Harmonic Distortion (THDi) <2.5%,Unity Output Power Factor @ 35deg C consisting of

Rectifier, Inverter, External Isolation Transformer, BatteryDC Circuit Breaker with necessary MS enclosure, InbuiltStatic BY PASS Panel (Input & output switches and AutoStatic & Manual Bypass Switches), necessary cable alleyshall be provided if cable entry/exit for UPS unit is frombottom/sides and necessary hardware & software forBMS Intergration with communication port RS 485 (Status Monitoring ), all interconnecting Copper cables(Battery bank to Battery DC Circuit breaker, Battery DCCircuit breaker to UPS, complete as required) withnecessary adequate size of copper lugs etc., withnecessary base channels/supports complete as requiredand all other necessary accessories required as perdetailed specification.

No. 1

487 Supply, Installation, Testing and Commissioning ofSealed Maintenance Free Batteries to support 60KVA for20 minutes complete with intercell connectors & coppercables, battery stand made out of Powder Coated MSAngles with adequate supports to carry the load of thebatteries.

No. 1



488 Supply, Installation, Testing and commissioning of MicroProcessor Controlled 1 x 20KVA standalone UPS (Application: For Emergency Lighting, BMS, VAV &Security service loads) input supply of 415 Volts +/- 15%,3 Phase, 50 Hz ± 10%, an out put of 415 Volts ±1%, 3Phase 50 ± 0.1 Hz , Input Power Factor <=0.99, Input TotalHarmonic Distortion (THDi) <2.5%, Unity OutputPower Factor @ 35deg C consisting of Rectifier,Inverter, Battery DC Circuit Breaker with necessary MSenclosure, Inbuilt Static BYPASS( Input & output switchesand Auto Static & Manual Bypass Switches), necessarycable alley shall be provided if cable entry/exit for UPSunit is from bottom/sides and necessary hardware &software for BMS Intergration with communication portRS 485 ( Status Monitoring ), all interconnecting Coppercables (Battery bank to Battery DC Circuit breaker, BatteryDC Circuit breaker to UPS complete as required)with necessary adequate size of copper lugs etc., withnecessary base channels/supports complete as requiredand all other necessary accessories required as per

detailed specification.

No. 2

489 Supply, Installation, Testing and commissioning of MicroProcessor Controlled 1 x 10KVA standalone UPS (Application: For Emergency Lighting, BMS, VAV &Security service loads) input supply of 415 Volts +/- 15%,3 Phase, 50 Hz ± 10%, an out put of 415 Volts ±1%, 3Phase 50 ± 0.1 Hz , Input Power Factor <=0.99, Input TotalHarmonic Distortion (THDi) <2.5%, Unity Output PowerFactor @ 35deg C consisting of Rectifier, Inverter, BatteryDC Circuit Breaker with necessary MS enclosure, InbuiltStatic BYPASS( Input & output switches and Auto Static &

Manual Bypass Switches), necessary cable alley shall beprovided if cable entry/exit for UPS unit is frombottom/sides and necessary hardware & software forBMS Intergration with communication port RS 485 (Status Monitoring ), all interconnecting Copper cables(Battery bank to Battery DC Circuit breaker, Battery DCCircuit breaker to UPS complete as required) withnecessary adequate size of copper lugs etc., withnecessary base channels/supports complete as requiredand all other necessary accessories required as perdetailed specification.

No. 1

490 Supply, Installation, Testing and Commissioning of

Sealed Maintenance Free Batteries to support 10KVA for20 minutes complete with intercell connectors & coppercables, battery stand made out of Powder Coated MSAngles with adequate supports to carry the load of thebatteries.

No. 1



491 Supply, Installation, Testing and commissioning of MicroProcessor Controlled 1 x 5KVA standalone UPS (Application: For Emergency Lighting, BMS, VAV &Security service loads) input supply of 415 Volts +/- 15%,3 Phase, 50 Hz ± 10%, an out put of 415 Volts ±1%, 3Phase 50 ± 0.1 Hz , Input Power Factor <=0.99, Input TotalHarmonic Distortion (THDi) <2.5%, Unity Output PowerFactor @ 35deg C consisting of Rectifier, Inverter, BatteryDC Circuit Breaker with necessary MS enclosure, InbuiltStatic BYPASS( Input & output switches and Auto Static &Manual Bypass Switches), necessary cable alley shall beprovided if cable entry/exit for UPS unit is frombottom/sides and necessary hardware & software forBMS Intergration with communication port RS 485 (Status Monitoring ), all interconnecting Copper cables(Battery bank to Battery DC Circuit breaker, Battery DCCircuit breaker to UPS complete as required) withnecessary adequate size of copper lugs etc., withnecessary base channels/supports complete as requiredand all other necessary accessories required as per

detailed specification.

No. 2

SECTION – K : LIGHTNING PROTECTION






ADVANCED LIGHTNING PROTECTION SYSTEM

492 Supply,Installation,Testing and commissioning of the

Advanced Lightning Protection CSE Air Terminal withall accessories required for its proper functioning. Theelevated pole should be fitted firmly attached to the wallor column with suitable guy wire system as permanufacturer recommendations to be provided.(Coverage 86m Radius)

Nos. 3

493 84 Supply,Installation,Testing and commissioning of theHVSC down conductor shall be consists of copperconducors, inner insulation, outer copper conductor,conductive sheaths, all cencentrically arrangements outerdiameterr of the down conductor shall be less than 37mm.The main conductor cross sectional area is 50 sq.mm Thedown conductor shall be placed minimum wall thicknessand minimum bending radius is 0.5m.The downconductor 50 sq.mm / 37mm / OD weight is 2.050 kg

ermetre.

RMT 450



494 Supply,Installation,Testing and commissioning of theLightning Strike Recorder designed for easy mountingon the down conductor to effectively count the number ofliightning strikes captured by the air terminal. Therecorder sensitive range of 1500 amps to a maximum of220KA @ 8/20µs. The recorder is self powered and doesnot require the use of battery or any other external powersource etc.

Nos. 3

495 Supply,Installation,Testing and commissioning of efficientearthing system with copper bonded earth rod, Clamp,Copper Tape, Ground Resistance Improvement powderall as required including excavation of earth etc asrequired as per manufacture recommendation.(Tripodearthing with 3 Nos. of earth pit)

Nos. 6

496 Supply of 25x3mm copper Down Conductor RMT 100

497 Supply of tape clip for fastening the DownConductor.

Nos 300

Aviation Lamp Fittings:

498 Supply, fixing of 2x12W LED cluster integral type aviation

lamp at topmost height of the building with Auto ON /OFF photo cell controller, connecting wires upto aviationlamp including all connected accesories etc as per thespecification.

No. 3

SECTION – L : Solar system






The complete Solar PV system should have a warranty

and after sales service for 5 years

499 Supply, erection, testing and commisioning of15Kwp solar roof top grid tie system complete with allaccessories and as mentioned below and as per thedetailed technical specifications

No. 1

250 Wp Solar Array (high efficiency multicrystalline modules)Galvanized MS Module mounting structure

15KWp,3Phase,415V,50HZ, Power Conditioning Unitwith MPPT Solar Charge Controller and Data Logger

Data logging and monitoring system

Array & Main junction boxesAC Distribution panel

Earthing Kit as per IS 3043

Lightning arrestor

Installation Hardware Kit

1C x 4 sq.mm PVC Copper Cables



Statutory permissions and approvals



Electrical Works ( Interior Works )

SECTION – M : SUPPLY AND FIXING OF LIGHTING

LUMINAIRES & FANS






Samples to be submitted and get approval fom Architect

Consultant before procurement

For LED light fittings, the complete luminaire should

have a warranty for 5 years which includes the housing

+ LED + Driver

500 Wipro WCP 37226 SGW or equivalent

2X26W CFL RECESS MOUNTED DOWNLIGHTLUMINAIRE WITH SATIN FINISH REFLECTOR

Nos 296

Lamps: 2X26W CFL

501 Wipro WCP 27218SGW or equivalent

2X18W CFL RECESS MOUNTEDDOWNLIGHTER WITH FROSTED GLASS

Nos 520

Lamps: 2X18W CFL

502 Wipro WIF 20128SGW or equivalent

1X28W T5 SAVIOUR-SLIM ENERGY SAVINGCHANNEL SUITABLE FOR FTL (T5) LAMP

Nos 152

Lamps: 1X28W T5

503 Wipro WIF 30228SGW or equivalent

2X28W SAVIOUR - SLIM ENERGY SAVINGCHANNEL SUITABLE FOR FTL (T5) LAMPS WITHBI-DIRECTIONAL REFLECTOR

Nos 108

Lamps: 2X28W T5

504 Wipro WVF 22414SGW or equivalent

4X14W T5 RECESS MOUNTED DIRECT LIGHTLUMINARIE

Nos 564

Lamps: 4X14W T5

505 Wipro GRP SGW 90226 or equivalent

2X26W CFL RHYTHM - PENDENT MOUNTEDLUMINAIRE WITH PRISMATIC DIFFUSER

Nos 26

Lamps: 2X26W CFL

506 Wipro GCH 35070 or equivalent

1X70W KOMPASS UNO-RECESS MOUNTEDMETAL HALIDE DOWNLIGHTERS

Nos 30

Lamps: 1X70W MH lamp

507 Wipro GCH 35035 or equivalent

1X35W RECESSED GIMBALL LUMINAIRE Nos 96Lamps: 1X35W MH lamp

508 Wipro WIP 53236 SGW or equivalent

2X36W CFL SURFACE MOUNTED IP 54BOTTOM OPENING TYPE CLEAN ROOMLUMINAIRE SUITABLE FOR CFL(TC-L)LAMP

Nos. 3

Lamps: 2X36W CFL

509 Wipro WRF 80128 SG or equivalent



1X28W T5 INDOOR DECORATIVE LUMINAIRESUITABLE FOR T5 LAMP

Nos 10

Lamps: 1X28W T5

510 Wipro WVP 45218 or equivalent

2X18W CFL SURFACE MOUNTED MIRROR OPTICLUMINAIRE WITH PARALITE P5 LOUVRES

Nos. 8

Lamps: 2X18W CFL

511 Wipro WVF 48228 SGW or equivalent

2X28W T5 SURFACE MOUNTED LUMINARIE WITHUNIQUE DUAL FINISH LOUVRE SYSTEM SUITABLEFOR FTL(T5) LAMP

Nos 45

Lamps: 2X28W T5

512 Wipro WDF 9128 SG or equivalent

Wall light patti fitting Nos 601Lamps: 1X28W

513 Wipro WRP 21111 or equivalent

Mirror light fitting (2feet patti fitting) Nos 86Lamps: 1X11W CFL

514 Wipro WKP 14 or equivalentBulk head fitting Nos 145Lamps: 1X9W CFL

515 Wipro WFH51150 or equivalent or equivalent

Compact Sturdy general purpose floodlight with integralgear, housing made of non-corrosive, high pressure diecast aluminium with low copper content and blackpowder coated finish, heat resistant EPR gasket with IP-65suitable for use with High Pressure Metal Halide MHN-TD 150W lam

Nos 15

Lamps: 1X150W MHL

516 Bajaj BRBOL 118 or equivalent

Renaissance - Integral Bollard with cylindrical shapehousing, spun aluminium hat shape top cover fixed withclear acrylic cover

Nos 30

Lamps: 1X18W CFL

517 Bajaj BECBL 03 126 CFL B or equivalent

Renaissance - Integral Bollard with black epoxy powdercoated cylindrical bollard with antiglare louvers diffuserin clear acrylic cover.

30

Lamps: 1X26W CFL

518 Similar to Wipro LD70-400-XXX-27-XX (Spotz LED)

Efficacy > 100lumens / watt

Color temperature: 2700 deg Kelvin

High efficiency Prismatic collimator lens for better lightdistributionBlack anodized aluminium heat sink for effective heatdissipationAesthetically textured chrome plated bottom Finish Nos 25Lamps: 1 X 4W LED



519 High performance PIR occupancy presence detectros forautomatic control of lighting. Shall have adjustable offdelay timing varying from 10 sec to 99 min. Advance PIRsensor for occupancy and vacancy sensing with built-inswitching photo cell detector for daylight detection.Sensor has 2 way programming feature using knobsprovided on the sensor or with hand held IR device. Thesensitivity of the sensor can be adjusted in 9 differentsteps. The sensor has in built IR receiver to be operatedusing hand held IR remote control. Similar to WIPRO:COP 11010

Nos 100

520 Sliding type dimming system with select light level withslider - slide up to brighten, down to dim. Suitable for0–10 V dimmable fluorescent ballasts.Rated for maximum20 ballasts/40 mA control current.Requires mains voltageoccupancy sensor by another manufacturer to powerballasts. Similar to WIPRO: LSTV-F20B-FAW-M

Nos 10

521 High performance PIR occupancy presence detectros forautomatic control of lighting. Shall have adjustable off

delay timing varying from 10 sec to 99 min. Advance PIRsensor for occupancy and vacancy sensing with built-inregulating photo cell detector for daylight detection.Sensor has 2 way programming feature using knobsprovided on the sensor or with hand held IR device. Thesensitivity of the sensor can be adjusted in 9 differentsteps. The sensor has in built IR receiver to be operatedusing hand held IR remote control. Suitable for analoguedimming. Similar to WIPRO: CDA 13010

Nos 50

522 Supply, fixing, testing and commissioning of 1200mmsweep single phase ceiling fan with standard down rod,similar to Bajaj Elctra 50 (White).

Nos 506

523 Supply, fixing, testing and commissioning of 600mmsweep single phase ceiling fan with standard down rod,similar to Bajaj Maxima 600mm (White).

Nos 66

524 Supply, fixing, testing and commissioning of 300mm dialight duty single phase exhaust fan for toilets, Similar toBajaj Maxima DX (White).

Nos 241

525 Supply, fixing, testing and commissioning of 1400 RPMheavy duty 380 mm dia single phase exhaust fan withlouvers.

Nos. 3

526 Supply, fixing, cutting, threading and fixing of 25 mm MSconduit for fixing of down rods, including check nut, balland socket etc. after the installation the pipe shall paintedwith required colour as required at site condition.

RMT 2000

527 Supply and fixing chain suspender with suitable anchorplatners for mirror optics light fititngs in office floors.

RMT 2000

SECTION – N : SUPPLY AND FIXING OF SPECIAL

LIGHTING LUMINAIRES








Samples to be submitted and get approval fom Architect

before procurement

Type-C, Bachelor and Transit accomodation (Option-1)

528 Entrance light above door

The Ledino flush wall bracket is a futuristic themed light.The half bowl fitting is finished in white and features ahollowed out space into which 2 down lights shine. Thefitting measures 13.1cm in diameter and protrudes fromthe wall 6.5cm. The light comes complete with 2 x 2.5wLED bulbs.

Nos 32

Similar to Philips Reference.No: 69085/31

529 Ceiling lights

Aluminum E27 Max 1 x 100W Material Glass withouthLamp

Nos 352

Similar to Philips Reference.No: QCG 301530 Wall lights

E27 Max 1x60W Material Glass withouth Lamp Nos 224Similar to Philips Reference.No: QWG 301

531 Balcony lights

Material Synthetic, Color White IP20, LampIncluded, 1x22W 230V

Nos 64

Similar to Philips Reference.No: 30161

532 Toilet mirror light

Mirror lamps chrome 1x8W 230V - Chrome finish Nos 128Similar to Philips Reference.No: FWZ 300

533 Store light

Aquafit QCZ801 G9, Max. 1x 25W - Chrome finish Nos 64Similar to Philips Reference.No: QCZ801

534 Toilet down lighter

Genie E27, 14W not included,With toughened glasscover, finish -nickle satin

Nos 64

Similar to Philips Reference.No: FBG302

Type-C, Bachelor and Transit accomodation (Option-2)


Wall light - Material Metal,Color white,On/off switch onarticle, IP code: IP20, protection against objects biggerthan 12.5 mm, no protection against water,Wattage

bulb included: 2.5 W, Light color 4000K cool white

Nos 32


536 Ceiling lights

Ceiling Light - Material Glass, color gold E27, 1NormalLamp, Lamp Excluded, Non Dimable

Nos 352

Similar to Philips Reference.No: QCG 309

537 Wall lights



Wall Light - Material Glass, color gold E27, lamp1x60W,Lamp Excluded, Non Dimable

Nos 224

Similar to Philips Reference.No: QWG 315

538 Balcony lights

Ceiling Light, Balcony Garden,Material - Steel, ColorWhite,Lamp Excluded, Non Dimable

Nos 64

Similar to Philips Reference.No: ECB 300

539 Toilet mirror lightMirror lamps chrome 1x8W 230V - Chrome finish Nos 128Similar to Philips Reference.No: FWZ 300

540 Store light

Aquafit QCZ801 G9, Max. 1x 25W - Chrome finish Nos 64Similar to Philips Reference.No: QCZ801



Nos 64


Type-D & VIP rooms


Wall light - LED 2.5 W, Material: Glass, Color: Chrome,premium Quality,Energy saving: 80 %, Lamp Included

Nos. 4


543 Ceiling lights living (double ht)

Pendant Light FPG701 Material Steel, Finish Aluminum -Suspension Light, Lamp included , base cap 2GX13

Nos. 8

Similar to Philips Reference.No: FPG701

544 Ceiling lights

Ceiling Light - 37246 ceiling lamp chrome 9x2.5WSELV,Material: Glass, Color: Chrome, premium

Quality,Energy saving: 80 %, Lamp Included

Nos 20


545 Wall lights

Wall light - LED 2.5 W, Material: Glass, Color: Chrome,premium Quality,Energy saving: 80 %, Lamp Included

Nos 31


546 Toilet Mirror Light

Mirror Light cap: GX53,Wattage bulb included: 9 W,Lightcolor: 2700K warm white,IP code: IP44, protection againstobjects bigger than 1 mm, protection from splashed water,Material Metal, color chrome

Nos. 6

Similar to Philips Reference.No: 34312/11

547 Balcony lights

Ceiling Light, Balcony Garden,Material - Steel, ColorWhite,Lamp Excluded, Non Dimable

Nos 14

Similar to Philips Reference.No: ECB 300

548 Store light

Aquafit QCZ801 G9, Max. 1x 25W - Chrome finish Nos. 8Similar to Philips Reference.No: QCZ801





Nos 10


OFFICE AREA

550 Mouette (Reference.No: L 860710)

Extruded aluminium structure; rotational mouldedpolypropylene diffuser; steel suspension wires Max

1900mm to use 4 x 24w T5 tubes with Dali DimmableBallst.

Nos. 4

Similar to Artemide (Light Art) or equivalent

551 Channel (Reference.No: 436LEV.128X.8)

Recessed Fixture with Aluminium profile,trim,Acrylic diffuser and Dali Dimmable ballast for 1 x 28w T5tube

Nos 52

Similar to Regent (Light Art) or equivalent

552 Umbrella (Reference.No: 00-2727-AP-05)

Pendant in Black lacquered body,Golden pleated interiorshade and frosted glass at bottom to hide the lamp to use3 x max 14w CFL.

Nos. 7

Similar to LEDSC-4 (Light Art) or equivalent

553 Castor (Reference.No: 8332)

Pendant with white base and opal glass for E27 max 27wSpiral CFL.

Nos. 4

Similar to Light Art or equivalent



Nos 4




Nos 4


556 Similar to Ligman Mustang 34 largw single tennis court

luminaire (Catalogue.No:93051-SC76)

Large size rectangular shape area light distribution formetal halide lamps or sodium vapour discharge lamps 70-400w. A high quality reflector design creates broad spreadlight distribution. Main application for lighting of public,private roadways, car parks, exhibition areas, servicestations, truck stop and sports grounds.

Aluminium housing with high corrosion resistance.Stainless steel screws. Durable silicone rubber gasket andclear toughened glass with hinge aluminium frame for in-

position lamp replacement. Anodized high purityaluminium reflector. Main housing is powder paint withhigh corrosion resistance with chemical chromatisedprotection.

Nos 1

Lamps: HIT 1000W

SCHEDULE - F - DG Works

DG SET WITH SCRUBBER, EXHAUST STACK AND

CONNECTED WORKS





557 Supply, Installation, Testing and Commissioning offactory assembled and factory tested, water cooled,turbo charged after cooled diesel engine alternator setcapable of generating full load of 1250 KVA capacity at40° C, power factor not less than 0.8 lag, 415 Volts,

1500rpm, 3 phase, 50 Hz, AC supply and driven withdiesel engine complete with all accessories such asBase frame, residential silencer, radiator, alternatorcapable of delivering 415 Volts, 50Hz, 3 phase, PF 0.8,1250 KVA load, coupling arrangement of alternator withengine, coupling guard, water pump, oil pump, fuel filter,oil filter, air filter, exhaust flexible piping, fuel tank (990Litres capacity of day tank), fuel transfer hand pump withsuitable hose pipe, battery 24 Volts and 200 AHcapacity, battery charging

Nos. 2

alternator, engine control panel, anti-vibration spring typemounting (quantity as per the manufacturer‟s

recommendation),conducting of trial run and A/T as per special conditionsSuitable for acoustic enclosure installation but withoutacoustic enclosure and standard type of engine alternatorcontrol panel etc. complete as per specifications.(Excluding cost of foundation).

Note : The sucessful tenderer should confirm that theengine model shall be capable of delivering minimum1250KVA and suitable for delivering 1250 KVA whencoupled with alternator given below at site condition asrequired. The Acoustic Enclosure is included seperately.

558 Supply, Installation, Testing and Commissioning ofacoustic enclosure suitable for 1 No. 1250 KVA radiatorwater cooled diesel generator with all accessoriesfabricated with 16 SWG CRCA sheet steel, mineral woolinsulation of high density with perforated GI sheetcovering, ventilation system complete with fans andlouvers, doors, inside temperature controller, insideillumination with energy efficient T5 fluorescent fittings,wiring for light and plug points with suitable size andnumber of PVC insulated copper conductor cable onsurface MS conduit system, i/c. MCB type distributionboard, earthing complete as per the Specification and the

drawing enclosed.(The above enclosure should be as perCPCB norms. The current approval certificate shall besubmitted by the firm).The day tank of 990 Litres shall bemounted on a suitable pedestal with weather proofenclosure nearer to the DG set. (Excluding cost offoundation). The necessary details such asweight(dynamic & static weight), sizes shall be furnishedfor the execution.

Nos. 2



559 Supply, Installation, Testing and Commissioning ofControl panel indoor, floor mounting type with2000Amps, 4pole 65KA ,EDO type ,air circuit breakerwith shunt release, shutter assembly, door interlock andother required accessories, complete set of instrumentpanel,protection release/relays, auto start/stoparrangement as per detailed specification.The panel shallbe installed inside the acoustic enclosure.

Nos. 2

560 Supply,Installation, Testing and Commissioning of AMFwith Auto Synchronising control panel with Auto Loadsharing arrangement of indoor, floor mounting type with2 Nos. 2000Amps, TP, 65KA ,EDO type ,air circuit breakerwith shunt release, shutter assembly, door interlock andother required accessories and 250Amps,4 pole, neutralisolating contactor as incoming with complete set ofinstrument panel with accessories, protectionrelease/relays etc. and 1No. 4000Amps, 4pole, 75KA,EDO ACB with shunt release, shutter assembly, doorinterlock and other required accessories as bus coupler &

2 Nos. 2000Amps, 4Pole, 65KA ,EDO type ,air circuitbreaker with shunt release, shutter assembly, doorinterlock and other required accessories as outgoingfeeders with complete set of instrument panel withaccessories, protection release/relays etc.

No. 1

and necessary electrical interlocking arrangementbetween incomer and bus coupler by hardware controlwiring along with PLC (Programmable Logic Control).The hardware control wiring for MPCC, AMF Panel,Capacitor Panel, Auto Synchronisation Panel and othernecessary control wiring and PLC operation shall be

feasible to extend for the panel as per the detaileds ecification and drawin s enclosed.

561 Supply, installation, Testing and Commissioning of wetscrubber with packing media and connected accessorieslike scrubbing tank 1No., scrubbing pumps 2Nos. (1 mainand 1standby) interconnecting pipe line works with allaccessories and control valves, suitable supports for thescrubber, required ducting for the scrubber assembly i/c.dampers for bypass arrangement, neutralisation system,suitable for 3Nos. 1250KVA DG set ( 2 Nos. at present + 1No Future), hot gas inlet and outlet arrangements, onlinePH monitoring and connected electrical works i/c. controlpanel, earthing, starter for pump sets, control and power

copper cabling, minor civil works, painting, sign writingcomplete as per specification and drawings enclosed etc.as required. (Excluding cost of foundation).

No. 1



562 Supply and Laying of 50mm x 10mm copper flat fromearth electrode in 80mm dia B class GI, directly in groundincluding earth work excavation, refilling the trench, withall accessories, jointing the flats with lap joint with 2Nos.of bolt/nuts/spring washers/check nuts completed etc.as re uired.

RMT 50

563 Supply and fixing of earthing station with 2Nos X 600mmx 50mm x 12.5mm copper busbar on suitable No. ofsupporting insulators having machine made holes forincoming/outgoing earth flats, painting and sign writingetc as required.

No. 4

564 Supply and fixing of 10" dia MS exhaust pipe class Bsuitable for 1250 KVA engine exhaust line including withall accessories such as bends,.flanges, gaskets,condensation removal plug, fixing of flexible coupling,residential silencer supplied along with the engine.Providing necessary MS angle iron supports for the pipeline and the silencer, welding arrangements/ flanged joints with bolts/nuts as per the site conditions.Terminating the pipe line/ ducting in scrubber and

chimney including the complete pipe line/ duct ofinsulation with 50mm thick glass wool, polythenecovering,chicken mesh and aluminium cladding completeas per the specifications etc. as required.

RMT 16

565 Supply and fixing of 14" dia MS exhaust pipe class Bsuitable for 1250 KVA engine exhaust line including withall accessories such as bends,.flanges, gaskets,condensation removal plug, fixing of flexible coupling,residential silencer supplied along with the engine.Providing necessary MS angle iron supports for the pipeline and the silencer, welding arrangements/ flanged joints with bolts/nuts as per the site conditions.

Terminating the pipe line/ ducting in scrubber andchimney including the complete pipe line/ duct ofinsulation with 50mm thick glass wool, polythenecovering,chicken mesh and aluminium cladding completeas per the specifications etc. as required.

RMT 60

566 Supply & fixing of 50mm thick glass wool insulation forthe 1250KVA engine residential silencer including cutting,fixing of glass wool, polythene covering,chicken meshand aluminium cladding complete as per thespecifications etc. as required.

Nos. 2

567 Supplying and laying of 25mm dia , B class MS pipe, fuelline for the interconnection of the reserve tanks to day

tank and day tank to engine i/c. fuel transfer pumps withall accessories such as bend,elbow, coupling, union,plugs,flanges,bolts/nuts,gaskets, making threadedends/welding as per the site condition laying in thefollowing manner etc. as required.

a In the exposed surface the pipe line shall be painted withone coat of primer and two coats of synthetic enamelpaint i/c. with necessary supports complete as required.

RMT 40



b In soil , below 0.5 Mtrs from the ground level , the pipeline shall be painted with one coat of hotbitumen,wrapping with 3 layers of hessian cloth dippedin hot bitumen i/c. with necessary supports complete etc.as required.

RMT 30

568 Supplying and fixing of outdoor weather proof reservefuel day tank made up of 3mm thick MS sheet, 990 ltrscapacity i/c. cutting, welding,grinding,providinginlet,outlet, overflow, drain, air vent, inlet fuel filter, fuellevel indicator with scale, painting,fixing with suitablesize MS angle iron frame work on the existing foundationetc. as required. (Excluding cost of foundation).

Nos. 2

569 Supply, Installation,Testing and commissioning of fueltransfer pumps 1 HP capacity, self priming, flame proofpumps 2Nos. (1No. Main and 1No. Standby) i/c.installation of pump sets on the existing foundation,connected fuel pipe line work with necessary controlvalves, to fill the reserve tank from barrels and to fill theday tanks from the reserve tanks i/c. all electrical works

such as control MCB, starter,changeover switch, controland power wiring with PVC insulated copper conductorcabling, end terminations, earthing thepumps,painting,sign writing and complete as required.(Excluding cost of foundation).

Nos. 2

570 Supply and laying of the following PVC insulated, PVCsheathed armoured Copper conductor cabling fromengine control panel to AMF control panel and batterycharger, day tank with suitable clamping arrangement,end terminations, earthing the glands, laying on theexisting cable tray /trench, painting complete etc. asrequired.

16 Core X 2.5Sq.mm Copper cable RMT 100571 Supply and fixing 200mm width cable tray suspended

from the ceiling or supported from the ground withsuitable angle iron supports. The tray shall be made up of38mmX38mmX5mm MS angle iron and interconnectedwith 2Nos.X25mmX3mm MS flat at every 150mm intervalwith necessary painting with one coat of red oxide paintand two coat of enamel paint etc. as required.

RMT 100

572 Supply and fixing of 1200mm X 600mm size 22 guage GIsheet board for display the name plate details of DG setwith suitable frame work i/c. fixing on the accousticenclosure, painting,sign writing etc. as required.

Nos. 2

573 Supply, Installation, Testing and Commissioning of thestructrual stack height of 30 mtr from ground level usingvarious size of GI channels and Supports of ResidentialSilencer, Fuel Pipe and busduct etc. Detailed design alongwith all calcuation details shallbe submitted by thesucessful vendor. The rate shall inclusive of foundationbolt, base plate for the stack etc.

MT 12



Lift Works

LIFT AND ELEVATOR

574 PASSENGER LIFT

Supplying, installation, testing & commissioning ofPassenger lift for various buildings of standard designconforming to latest lift act and modern lift withmicroprocesor including AC- Gearless synchronous

V.V.V.F drive system in the existing lift well / shafthaving the following speed, travel and stops for variousbuildings. The lift car interiors such as carenclosure,ceiling, handrailing,door panelling,Jambs in allfloors,fan, car light and others shall be complete as perspecification and two hours fire rated for landing doors.

The lift shall be of excellent quality and shall haveluminous white square flush mounted Braille pushbuttons,intelligent group controls of four lifts, floorannouncement system, Gearless and other features as perdetailed specifications attached. The lift car shall have twoparallel car operating control panels in automatic mode

with or without attendant (duplex mode).

The lift equipment being machine room the machine willbe fixed on the guide rail and machine room less elevatorlift assemble within the hoist way at the last landing. Allthe lift equipments, i/c car, car doors self-levellingdevices, control devices, indicators, landing doors,indicators, terminal buffers,hoisting suspension ropesshall be of steel of suitable size for safety devices i/c allwiring connection, interconnection and all connectedequipments shall be as per specifications. The work alsoincludes all structural items in machine room and abovethe lift well like RCC block, & MS girders required for liftinsallations & providing miscellaneous items likesupports for guide rails, overhead gears, scaffoldings, sillprojections, facia inside the lift well, minor building workslike making sockets, holes etc. i/c making good thedamages.

The rate shall include approval / obtaining completioncertificate from the electrical / lift inspectorate of LocalCompetent Electrical Authority for installation andcommissioning of lifts before handing over the entireinstallation of the lift, as complete in all respectscomplying with all relevant standard specification and as

directed by the Engineer-Incharge.

a 13 passenger of 884kgs without Machine room ofminimum speed of 2.0m/sec (min) with a total travel of53.60 mtrs. Stilt plus 18 floors servicing 19 stops and 19landings on same side.

Nos. 2

b 13 passenger of 884kgs without Machine room ofminimum speed of 1.5m/sec (min) with a total travel of32.95 mtrs. Ground plus 11 floors servicing 12 stops and12 landings on same side.

Nos. 2



c 6 passenger of 408kgs without Machine room ofminimum speed of 1.0m/sec (min) with a total travel of12.6 mtrs. Ground plus 3 floors servicing 4 stops and 4landings on same side.

Nos. 2

575 SERVICE LIFT

Supplying, installation, testing & commissioning ofService elevator for various buildings of designconforming to latest lift act and modern lift with includingAC Gearless synchronous digitalised microprocessorbased programmable VVVF controller in the existing liftwell / shaft having the following speed,travel and stopsfor various buildings. The lift shall be complete withfactory enamelled / MS paint finish for car enclosure,ceiling & car doors (all four sides) and landing doors shallbe opening telescopic stainless steel door (two hours firerated) and three sides guard rail,handle inside the car.(with all car interiors complete as per specification)

The lift shall be of excellent quality and shall haveluminous white square flush mounted braille push

buttons, intelligent group of simplex controls,collective,floor announcement system, Gearless machine and otherfeatures as per detailed specifications attached. The lift carshall have car operating control panel (1no) in automaticmode (with or without attendant) and from one panel inattendant mode.

The lift equipment will be installed in the machine roomdirectly above the lift well and machine room less elevatorlift assemble within the hoist way at the last landing. Allthe lift equipments, i/c car, car doors self-levellingdevices, control devices, indicators, landing doors,indicators,terminal buffers,hoisting suspension ropes

shall be of steel of suitable size for safety devices i/c allwiring connection, interconnection and all connectedequipments shall be as per specifications. The work alsoincludes all structural items in machine room and abovethe lift well like RCC block, & MS girders required for liftinsallations & providing miscellaneous items likesupports for guide rails, overhead gears, scaffoldings, sillprojections, facia inside the lift well, minor building workslike making sockets, holes etc. i/c making good thedamages.

The rate shall include approval / obtaining completioncertificate from the electrical / lift inspectorate of LocalCompetent Electrical Authority for installation andcommissioning of lifts before handing over the entireinstallation of the lift, as complete in all respectscomplying with all relevant standard specification and asdirected by the Engineer-incharge

a One Service Elevator of 1420 kgs without Machine roomof minimum speed of 1.0m/sec (min) with a total travel of12.60 mtrs. Ground plus 3 floors servicing 4 stops and 4landings on same side.

Nos. 1



b One Service Elevator of 1360 kgs with Machine room ofminimum speed of 1.0m/sec (min) with a total travel of6.00 mtrs. Ground plus 1 floors servicing 2 stops and 2landings on same side.

Nos. 1

HVAC Works (Heat Ventilation & Air-Conditioning)

I AIR COOLED SCROLL CHILLERS

576 Design, supply, customs clearance , freight upto site,

Insurance, delivery, hoisting, installing, testing andcommissioning of the following items as shown on theequipment data and drawing for complete andsatisfactory operation and control and to local authoritiesapproval. The units shall be anti-corrosive suitable forcoastal area application.BMS interfacing type microprocessor controlled Roof topair-cooled liquid chiller package suitable for refrigerant R-

410A or R407c having multiple scroll type compressors(hermetic type) with hydronic pumps (1W+1Standby),unit mounted starters, controllers and complete as perspecification. The rate shall inclusive of vibration isolators(moulded elastomeric isolators) to arrest noise and

vibration.Chillers capacity of each chilling unit will be as follows:

Capacity : 40 TR (minimum) at 40ºC Ambient Nos. 1Water in : (+) 12 Deg C

Water Out : (+)7 Deg C

Fouling factor : 0.0001 FPS units

577 Flanges of resilent vibration isolating material (like rubberfor example) at the inlet and outlet of chillers and pumpsalong with necessary bushes-also of similar material tominimize transmission of vibration to connected piping.

65NB Nos. 9578 Necessary sockets and nipples with shut off valves for

mounting sensors/transmitters on pipe line to interfacethe BMS system.

Set 1

579 Supply,installation testing and commissioning of Chillerisolator panel outdoor type suitable for 40 TR Air cooledscroll cooled chiller with isolator

No. 1

580 Supply, fabrication and erection of grating from the curbof pedestal to provide easy and trouble free access,weather protective cowl for electrical panel and all specialtools and tackles for operation, assembling,commissioning and maintaining the chiller unit. It shallbe supplied / provided by the ACMV Contractor.

Kg 500

II AIR HANDLING UNITS AND ENERGY RECOVERY

UNIT

581 AIR HANDLING UNITS - FLOOR MOUNTED TYPE



Supply, installtion, erection testing and commissioning ofDouble Skin floor mounted AHU with 6 Row cooling coils(copper tubes with Aluminium fins construction) flatfilters section with 48 mm thick Non-woven synthetic prefilter, medium pressure fan section with centrifugal fan/s,sq.cage induction motor belt drive, belt guard, vibrationisolators, double canvas connections and with unitmounted emergency off station internally factory wiredbetween motors and emergency off station as perspecifications.

Frame of anodised extruded aluminium thermal breaksections and bolted together with cast aluminium, fittingsprovided at joints and the entire unit is supported onpainted steel channel frame. All the section shall bethermal break as the AHU is outdoor type. Casing panelsshall be of insulated sandwich made of 0.6mm thickpowder coated or plasticised sheet outside shall besuitable for out door application and 0.6mm thickgalvanised sheet steel inside with 50mm thick Puf

insulation media in between. One section of panel toanother and panel to frame work are bolted together withleak proof soft neoprene rubber gasket to prevent any airleakage. Air tight access doors with adjustable tensionlocking device for inspection wherever required.Common channel base to mount fan and motor assemblywith vibration isolator for smooth vibration freeo eration.The double skin air handler shall include for the followingand its final painting to code.Low leaking volume control damper in 1.6mm galvanised/ aluminium aerofoil blade, 16mm dia plated steel stubslocked to the blades with mechanical fasteners, heavy

duty moulded nylon bearings, neoprene rubber seals attips, aluminium compression seals at jambs, brass rollers,double linkage on panels over 1000mm in width etc.

Flexible connections at fan outlet constructed of the fire-resistant flexible double canvass sleeve as per thespecification.The price shall also include the following.

a) All internal wiring between limit switch and marinelights, power cabling copper earthing of air handling unitmotors, from the local control panel and control wiring

b) Bimetallic lugs shall be used at copper to aluminium

joints.c) Accessories and associated wiring between fire damperpanel to fire damper and AHU motor to close firedampers and shut-off AHU motor in the case of fire.

AHU Specifications:

Location-Terrace Floor

Cooling Capacity : 40.0 TR (Outdoor type) No. 1Dehumidified air quantity :13600 CFM



Chilled Water flow rate : 96.0 GPM

582 ENERGY RECOVERY UNIT

Supply,installation, testing and commissioning of Energyrecovery unit consists of exhaust air block and fresh airblock. Each block is made up of double skin constructiondesigned on modular concept basis and has provision forfan , motor, damper and filter. Each block module shall be

fitted with other block, housing heat recovery devices,washable metallic viscous filters (50mm thick) and inletand outlet dampers (extruded aluminium low leakageconstruction) with bird screen for supply and return air.Air flow parameters: Energy recovery unit complete withdesiccant coated aluminium media rotor seal GI structuralframe work to house rotor, drive system, rotor drivemotor, belt, pre-filter complete with starter panel. Theprice for energy recovery unit shall include the followinga) All internal wiring, power cabling copper earthing oftreated fresh air unit motors, from the panel and controlwiring b) Bimetallic lugs shall be used at copper toaluminium joints and as per specification.

The vendor shall select the suitable units with minimumleakage. The fresh air quantity required after leakage is asfollows.5220 cfm (Supply air fan and return air fan) -Outdoor type No. 1

ESP - 500 Pa for fresh air supply fan and 500 Pa for returnair fan

III VRV SYSTEM

583 Supply, Installation, testing and commissioning of VRVIndoor air conditioning units with direct driven fan, highefficient filter, inbuilt microprocessor thermostat,

electronic expansion valve, provision of fresh air ductconnection, wired PID remote controller, drain pump,necessary ceiling supports & vibration isolators,refrigerant charging, oil charging, control wiring anddrain connection, etc. The capacities and cfm are asmentioned below:-

a Multi Flow Cassette Units (Round/4-way) (VRV)

i Cooling Capacity: 39,600 Btu/hr Air Flow : 1130 cfm Nos. 11

ii Cooling Capacity: 31,700 Btu/hr Air Flow : 742 cfm Nos. 23

iii Cooling Capacity: 24,900 Btu/hr Air Flow : 671 cfm Nos. 8

iv Cooling Capacity: 19,800 Btu/hr Air Flow : 565 cfm Nos. 20

v Cooling Capacity: 16,000 Btu/hr Air Flow : 530 cfm Nos. 20

vi Cooling Capacity: 12,600 Btu/hr Air Flow : 459 cfm Nos. 33vii Cooling Capacity: 9,900 Btu/hr Air Flow : 459 cfm Nos. 67

b 2-Way cassette units (VRV)

i Cooling Capacity: 19,800 Btu/hr Air Flow : 424 cfm Nos. 2

ii Cooling Capacity: 16,000 Btu/hr Air Flow : 424 cfm Nos. 16

iii Cooling Capacity: 12,600 Btu/hr Air Flow : 318 cfm Nos. 5

iv Cooling Capacity: 9,900 Btu/hr Air Flow : 318 cfm Nos. 9

c Ceiling Suspended unit (VRV)

Cooling Capacity: 39,600 Btu/hr Air Flow: 883 cfm Nos. 4



d Ceiling Mounted Ductable units (VRV)

i Cooling Capacity: 57,000 Btu/hr Air Flow: 1624 cfm Nos. 2

ii Cooling Capacity: 78,500 Btu/hr Air Flow: 2047 cfm Nos. 1

584 Supply, Installation and commissioning of energyrecovery unit combined with supply air fan, return airfan, suitable heat exchanger elements with necessarysupports, cabling, steel frame works etc.The capacity of

energy recovery unit as mentioned below

a Air Flow : 325 - 382 cfm Nos. 2

b Air Flow : 400 - 471 cfm Nos. 3

c Air Flow : 500 - 588 cfm Nos. 14

585 Supply, Installation, testing and commissioning ofOutdoor units consists of minimum one no of inverterscroll / rotary compressor, constant speed scrollcompressors, DC fan motor with aero-spiral fan blade, e-pass heat exchanger, safety valves, solenoid valves,receiver, capilary tube, check valve, electronic expansionvalve, high pressure switch, low pressure sensor, pressureregulating valve, refrigerant filter, stop valve,accumulator and outdoor refnet kits. Rate inclusive of R-410A / R-407C / equivalent refrigerant for entire circuits& oil pre charging, vibration isolators, supports, necessarycivil works for fountation/pedestal/steel frame works,etc.

a 18 HP Nos. 1

b 28 HP Nos. 2

c 34 HP Nos. 1

d 36 HP Nos. 1

e 38 HP Nos. 1

f 40 HP Nos. 1

g 48 HP Nos. 3

586 Supply and installation of central remote controller - I

touch screen controller suitable to connect upto multipleindoor and outdoor units (including integration with firealarm system, operate or monitor on / off, temperaturesetting etc.,) individually. The controller shall compatibleto connect with BMS.

Lot 1

587 Supply and installation of Refnet joints (Refrigerantbranch kit) for taking branches between two outdoorunits and various indoors as per VRV scheme drawings.The refnet joint set consists of both liquid and gas linebranch kits. The Refnet joint model name as follows.

a 22T Nos. 60b 33T Nos. 24

c 72T Nos. 55

d 73T + 73T Nos. 72

588 Supply and erection of 16 Gauge Hard drawn RefrigerantCopper pipes to integrate outdoor / indoor units. The rateshall inclusive of closed cell nitrile rubber insulation forcopper pipes. The pipe sizes and insulation thickness asfollows.

a 6.4mm dia with 9mm thick insulation RMT 699



b 9.5mm dia with 9mm thick insulation RMT 342

c 12.7mm dia with 13mm thick insulation RMT 916

d 15.9mm dia with 13mm thick insulation RMT 358

e 19.1mm dia with 19mm thick insulation RMT 247

f 22.2mm dia with 19mm thick insulation RMT 335

g 25.4mm dia with 19mm thick insulation RMT 59

h 28.6mm dia with 19mm thick insulation RMT 8

i 31.7mm dia with 19mm thick insulation RMT 141 j 34.9mm dia with 19mm thick insulation RMT 16

k 38.4mm dia with 19mm thick insulation RMT 153

l 41.3mm dia with 19mm thick insulation RMT 128

589 Supply and laying of 2C x 1.5 Sqmm PVC CopperArmoured Cable - Communication and Control cablingbetween indoor and outdoor units. The rate shall beincluding suitable size MS conduit with conduitaccessories and necessary fixing arrangement.

RMT 1750

590 Supply and laying of 2C x 0.75 Sqmm PVC CopperArmoured Cable - Control cabling for wired remote

controller.(optional)

RMT 1070

591 Supply and fixing in position of Heavy duty PVC pipe cutto required length with 9mm thick nitrile rubberinsulation, installed with all joints, reducer, necessaryelbows and tees.

a 40 NB RMT 562

b 25 NB RMT 596VRV SYSTEM SUMMARY

IV DX SYSTEM

592 DUCTABLE SPLIT UNITS

Supply,Installation,testing and commissioing of Ceilingmounted ductable splitunits of specified capacities with R

410A / R-407c refrigerant gas filling. The indoor unitsshall be ceiling mounted duct type. The Indoor unit shallcomprise of Fan, Cooling coil, Filter and Expansiondevice. The Outdoor unit shall comprise of scroll / rotaryCompressors, Air cooled condenser & Condenser fan. Ifmultiple compressors are offered, they shall haveindependent refrigerant circuits. Also, compressors shallbe cut-off automatically under part load conditions. Theunits shall have microprocessor controls. The outdoor unitshall be installed in the terrace level. The rate shallinclusive of control wiring between indoor and outdoorunits, refrigerant charging, insulated drain pipes andsupports for the indoor and outdoor units. The units shall

be selected for chennai Ambient conditions. The unitsshall be factory assembled and only the refrigerant pipingcarried out at site.it is inclusive of cabling between indoorand outdoor units and earthing of indoor and outdoorunits.

a Cooling Capacity: 1,32,000 Btu/h Air flow: 4400 cfm Nos. 1

b Cooling Capacity: 1,02,000 Btu/h Air flow: 3400 cfm Nos. 1

c Cooling Capacity: 45,000 Btu/h Air flow: 1235 cfm Nos. 1



593 HI WALL SPLIT UNITS

Supply and Installation of Hi-Wall Split air conditioningunits of specified capacities with R410A/R407Crefrigerant gas filling.The indoor units shall be wall fixingtype. The Indoor unit shall comprise of Blower, Coolingcoil, Filter and Expansion device. The Outdoor unit shallcomprise of inverter scroll / rotary Compressor, Aircooled condenser & Condenser fans. The outdoor unitshall be installed at terrace level.Scope shall include allsupports for the indoor and outdoor units. The units shallbe selected for Chennai Ambient conditions asspecified.Rate inclusive of suitable voltagestabilizer,cabling 20 Amps contactor with NO+NC (forremote operation through BMS) and control cable.

a Cooling Capacity: 36,000 Btu/hr Air flow: 811 cfm Nos. 2

b Cooling Capacity: 24,000 Btu/hr Air flow: 670 cfm Nos. 3

c Cooling Capacity: 18,000 Btu/hr Air flow: 572 cfm Nos 32

d Cooling Capacity: 12,000 Btu/hr Air flow: 350 cfm Nos. 2

594 CASSETTE UNITS

Supply, Installation and commissioning of DX Cassetteunits of specified capacities with R410A/R407Crefrigerant gas filling. The Indoor unit shall comprise of 4-way air flow Blowers, Cooling coil, Filter and Expansiondevice and drain pan. The Outdoor unit shall comprise ofinverter scroll Compressor, Air cooled condenser &Condenser fans. The outdoor unit shall be installed atterrace floor level. Scope shall be inclusive of suitablevoltage stablizer, all supports for the indoor and outdoorunits. The units shall be selected for chennai Ambientconditions as specified. Rate inclusive of 20 Amps

contactor with NO+NC (for remote operation throughBMS) and suitable earthing of indoor and outdoor units.

a Cooling Capacity - 36,000 Btu/hr Air Flow -988cfm Nos. 3

b Cooling Capacity - 24,000 Btu/hr Air Flow -670cfm Nos. 2

c Cooling Capacity - 18,000 Btu/hr Air Flow -529cfm Nos. 8

595 HI SENSIBLE FLOOR MOUNTED PACKAGED

UNITS



Supply,Installation,testing and commissioing of Hisensible floor mounted ductable packaged units ofspecified capacities with R-410A / R-407c / Equivalentrefrigerant gas filling. The indoor units shall be floormounted packaged type. The Indoor unit shall compriseof Fan, Cooling coil, Filter and Expansion device. TheOutdoor unit shall comprise of Hermetic scrollCompressors, Air cooled condenser & Condenser fan. Ifmultiple compressors are offered, they shall haveindependent refrigerant circuits. Also, compressors shallbe cut-off automatically under part load conditions. Theunits shall have microprocessor controls. The outdoor unitshall be installed in the terrce level. The rate shallinclusive of control wiring between indoor and outdoorunits, refrigerant charging, insulated drain pipes andsupports for the indoor and outdoor units. The units shallbe selected for chennai Ambient conditions. The unitsshall be factory assembled and only the refrigerant pipingcarried out at site.it is inclusive of cabling between indoorand outdoor units and earthing of indoor and outdoor

units.

Cooling Capacity: 1,98,000 Btu/h Air flow: 8250 CFM(2w+1s)

Nos. 3

596 Supply,erection and testing of Refrigerant Copper pipesof the following diameters to integrate outdoor /indoor units. The liquid line and suction line shall beinsulated with closed cell nitrile rubber insulation asspecified below.

a 6.4mm dia liquid pipe with 9mm thick insulation RMT 213

b 9.5mm dia liquid pipe with 9mm thick insulation RMT 128

c 12.7mm dia liquid pipe with 9mm thick insulation RMT 301

d 15.9mm dia liquid pipe with 13mm thick insulation RMT 312

e 19.1mm dia gas pipe with 13mm thick insulation RMT 28f 25.4mm dia gas pipe with 13mm thick insulation RMT 292

g 28.6mm dia gas pipe with 13mm thick insulation RMT 8

597 Supply and fixing in position of Heavy duty PVC pipe cutto required length with 13mm thick nitrile rubberinsulation, installed with all joints, reducer, necessaryelbows and tees.

a 40 NB RMT 103

b 25 NB RMT 112

598 Supply and laying of 3C x 2.5 Sqmm PVC Copper CableControl cabling between indoor and outdoor units.The rate shall be including suitable size GI conduit with

conduit accessories and necessary fixing arrangement.

RMT 428

599 Supply and laying of 2C x 1.5 Sqmm PVC Copper Cable -Control cabling between indoor and outdoor units. Therate shall be including suitable size MS conduit withconduit accessories and necessary fixing arrangement.

RMT 239



600 Supply and erection of following sizes Ladder type cabletray made out of 16G thick GI sheet folded to requiredshape with adequate number of supports for Insulatedrefrigerant pipe and cable conduits. The tray shall becovered 16G GI sheet at terrace and wherever exposed.

a 150mm wide RMT 48

b 300mm wide RMT 40

c 450mm wide RMT 2

V PRECISION AIR-CONDITIONING (PAC) SYSTEM

601 Supply, Installation, testing and commissioning ofMicroprocessor based floor mounted, bottom dischargeair cooled precision Packaged air conditioners with eco-friendly refrigerant.Acoustically insulated Indoor unit with DX cooling coil,filter, EC Fan, hermetically sealed scroll compressor,preheater, humidifier, automatic control thermostat andhumidistat, canvass connections, fixing/mountingaccessories, adjustable and lockable support brackets,

hardware rubber pads etc. The outdoor unit shall consistsof Air cooled condenser with condenser coil and propellerfansElectro-Mechanical Microprocessor panel, digital display,programmable control & recording unit complete withintelligent 16 digit 2 line alpha numeric display, functionkeys, cursor keys, free programmable keys, multi colorLEDS, inscription fields with integrated battery backupsupply at 24 V AC 50 Hz, starter, push buttons, SPP,thermal overload, safety cut-offs, MCBs provision receivezone fire alarm signal and tripping of PACs during thefire. The price shall be inclusive of he sequence controllerand necessary hardware for third party BMS integration.

Unit shall be fitted with high limit humidity sensor /humidistat mounted in the fan outlet and wired toprevent discharge of saturated air from the precision air-conditioner. The unit shall be provided with an underwater leakage sensor to be installed in the false flooringbelow the drain pan for floor discharge units.

The unit shall be selected to meet the required conditionat chennai ambient.Inside condition shall be maintained as 20 ± 1 °C DBT &

50 ± 5 % RHNominal Capacity: 23.0 TR, Air flow rate: 13780 CFM -

Downward Flow (4w+1s)Nos. 5

602 Supply and erection of 16 Gauge Refrigerant Copperpipes with closed cell nitrile rubber insulation to integrateoutdoor / indoor units as per specification.

a 15.9mm dia liquid line with 19mm thick insulation RMT 435

b 22.2mm dia hot gas line with 19mm thick insulation RMT 435



603 Supply and laying of Power cabling 4Corex16sq.mm withCopper armoured cable with PVC insulated, PVCsheathed, cables from the isolator (located nearby theindoor units) to the indoor units. (Vender shall confirmthe cable size based on the selected model)

RMT 50

604 Supply and laying of Control cabling 4core x 2.5 Sq.mmbetween indoor and outdoor units. The rate shall beincluding suitable size heavy duty PVC conduit withconduit accessories and necessary fixing arrangement.

RMT 450

605 Supply & fixing of sheet metal plenum box fabricatedfrom 22G GI sheet and branch duct with 24G GI sheetconnecting unit bottom to server room below falseflooring. The size of the plenum and branch duct shall beas per the drawing.

Nos. 5

606 Supply and fabrication of suitable angle iron frame workfor supporting the indoor units complete with 2 coats ofred oxide and enamel paint.

Nos. 5

607 Supply and fabrication of suitable steel frame work for

supporting all the condensing units as per site conditionand provide clear space for air intake / maintenancecomplete with 2 coats of red oxide and enamel paint. Allthe steel structure works, necessary civil works & RCCworks are in PAC vendor scope.

Lot 1

608 Supply and fixing of Powder coated Heavy duty floormounted supply air discharge grilles with Volume controldamper. Size: 600 x 600mm.

Nos. 64

609 Supply and fixing of Extruded Aluminium, powderCoated 0 degree deflection return air ceiling grilles of size600 x 600mm without Volume control damper

Nos. 64

610 Supply and fixing in position of Class B GI pipe(humidifier water line) cut to required length installed

with all joints, reducer, necessary elbows and tees,supporting arrangements, etc.

a 40 NB RMT 55

b 25 NB RMT 12

611 Providing and fixing in position the following Ball valvescomplete with end flanges / matching flanges, additionalsupports, fixing accessories etc. The valve shall bethermally insulated with 13mm thick nitrile rubberinsulation.25 NB Nos. 5PRECISION AIR-CONDITIONING (PAC) SYSTEM

SUMMARY

VI PIPES AND VALVES612 Supply, erection, testing and commissioning of chilled

water pipes. Pipes will be of MS Class C‟ up to 150mm diaas per IS 1239, 6 mm thick for 200mm and 250mm diapipes and 8mm thick for above 300mm dia as per IS 3589.Necessary RCC pedestals of size 600 x300x150mm highshall be provided at every 2200mm interval to run thechilled fluid piping above the floor level by ACMVcontractor.



All other pipe supports will have to be on regular pipehangers with spring and acceptable isolation in eachsupport. The quoted piping rate shall include forincorporating service flanges on all valves, strainers,service screen/basket strainer on the water line entry toall equipments like chilled water coils and chillers serviceflanges, descalling Tees, airvent valves, drain valves etc.,required to make the circuits fully operational. Thetemporary service strainers shall be removed anddiscarded after the first few hours of trial runs.

The unit rate for piping shall also include the chemicalcleaning and passivation as detailed in the specification.The insulation valves shall be considered as onemetre ofthe size.M.S angle /Channel also to be insulated.

Chilled Water piping with black steel pipes, bends,

Tees and fittings, factory made supports as follows

100 NB - MS Class C RMT 12

613 Supply and erection of FM approved Nitrile rubber as per

specification for pipe mentioned below:a 65 NB RMT 12

614 Providing and fixing in position the following bare, GIClass B pipe (make-up and drain) cut to required lengthand installed with all screw joints, reducer, necessaryelbows and tees.

a 40 NB RMT 26

b 25 NB RMT 45

615 Providing and fixing in position the following Butterflyvalves (PN16) complete with matching flanges,lockingdevices,extended flow control lever,thermal insulationwith aluminium clading and fixing accessories etc.. as per

specification65 NB - Lever operated Nos. 4

616 Providing and fixing in position the following Brass Ballvalves complete with end flanges/matching flanges,additional supports, fixing accessories etc. as perspecification25 NB - Lever operated Nos. 2

617 Supply and erection of balancing valves, non-risingspindle of stainless steel SS410 stem, stainless steel disc ofAISI SS410 with EPDM sealing on seat, double seal byEPDM back flow and graphic asbestos packing on spindleC1220 cast iron / aluminium / MS fabricated hand wheelwith pressure test cocks for measurements and regulation

of flow through pressure drop across the valves, 50mmthick EPS as thermal insulation with Aluminium claddingas specified, flanges boards, drain valves etc. suitable forcomputerized balancing instrumentation probes.

65 NB Nos. 1



618 Supply and installation of electronic, Self-balancing,pressure independent type dynamic balancing valve withintegrated 2-way modulating control valves in a singlebody. The actuator shall be capable of accepting 2-10VCD,4-20mA electric signal and shall provide similartransduced feedback output signal to control system. Theminimum close of pressure of actuator must be 1.5 timesshut off head of pump as per specification of followingsizes.65 NB Nos. 1

619 Supply and installation of 2-way Motorised valves(ON/OFF) with actuator working on 230 V of. If requirednecessary transformer to be included in the scope

65 NB Nos. 1

620 Supply and installation of MS fabricated „Y‟ type strainerwith removable brass /stainless steel (SS-316) screen(24G) with 3mm perforation and permanent magnet,drain piping(SS-410) complete with matching flanges and80mm thick EPS thermal insulation with aluminium

cladding as specified65 NB Nos. 1

621 Supply, installation and commissioning of Water Pressuregauges (bourdan type)complete with ball valve, gaugevalve mounting, fittings and copper tubing extensionwhere required

Nos. 4

622 Supply and erection of Thermometers of the mercury inglass stem type and copper separable well complete withguard etc. Mounted on water lines, thermowells, drainvalves, vent cocks etc., in the inlet and outlet of coolingcoil connections.

Nos. 4

623 Supply and erection of Automatic Air Vents shall beinstalled at all high sections of piping. The discharge from

this air vents shall be piped via tubes of appropriate sizeto the nearest waste drain pipe.1/2'' size Nos. 1

VII AIR DISTRIBUTION SYSTEM

624 Supply, installation, testing and balancing of AirDistribution System consists of factory fabricated sheetmetal ducting complete with supports (anchor fastnersand tie-rods, cradles, angle iron supports, GI bolts andnuts, 4mm thick self-adhesive neoprene rubber gasket,stiffeners, zinc chromate painted angle iron flanges,chipping and plastering of openings made for ductsupports etc., complete as per specification. The rates

quoted shall include turning vanes, straightening vanes,splitters, inspection doors probe, inlets with test openingsenclosures complete with locking caps, chain, gaskets,insulating plugs, and extension for insulated ductworketc.

a 1.2mm thick GSS (18G) ducting – factory fabricated Sqm. 8

b 1.0mm thick GSS (20G) ducting – factory fabricated Sqm. 218

c 0.8mm thick GSS (22G) ducting – factory fabricated Sqm. 401

d 0.63mm thick GSS(24G) ducting – factory fabricated Sqm. 909



e 0.55mm thick GSS (26G) ducting. – factory fabricated Sqm. 1771

625 Supply and installing of Acoustic insulation,Material shall be processed Nitrile Rubber foam. Thematerial should be fibre free. The density of the sameshall be within 140-180 Kg/m3.The material shouldhave a thermal conductivity not exceeding 0.050 W/mK.The maximum surface temperature the material shouldwithstand is 105º C and minimum temperature should be20ºC. The Thickness of the material shall be 15mm. Thematerial should conform to Class 1 rating for surfacespread of Flame as per BS 476 Part 7.

Sqm. 88

626 Supply and erection of Thermal Insulation ofSupply air duct with 9mm thick closed cell nitrile rubbertemperature range from -10ºC to +60ºC, Class O firecategory and as per specification.

Sqm. 653

627 Supply and installation of Thermal Insulation of Exposedsupply and return air duct with 25mm thick Pre factorylaminated with treated glass cloth of 205 gsm (blackcolour) nitrile rubber temperature range from -10ºC to

+60ºC, Class O fire category and as per specification.

Sqm. 75

628 Supply and installation of Flexible duct connectionsbetween main duct and diffuser plenums and main ductto cassette units shall be 25mm thick fiber glass pre-insulated, single ply/multiply Aluminium constructionand with multiple layers of polyester film glass fibercovered with mechanical lock sheets/ Aluminiumlaminated jackets-Fire resistant complete with Pre-fabricated and powder coated Aluminium angle framemounting brackets and supports

a 100mm dia Rmt 327

b 200mm dia Rmt 27

c 300mm dia RMT 10629 Supply and fixing of Spigot damper (Butterfly damper)

shall be installed from take off collar to diffuser plelumboxes and at plenum boxes (low leakage) made out of1.6mm galvanized sheet steel frame and blades of 1.0mmgalvanized steel with suitable links.

a 100mm dia Nos 218

b 200mm dia Nos 18

c 300mm dia Nos. 6

630 Supply and fixing of Extruded Aluminium, powdercoated Supply air diffusers with removable centre core

overall size 600 x 600mm without volume controldampers.

a 525 x 525mm neck size Nos 11

b 450 x 450mm neck size Nos. 6

c 375 x 375mm neck size Nos 20

d 300 x 300mm neck size Nos 28



631 Supply and fixing of Extruded Aluminium, powderCoated Return air diffusers with removable centrecore overall size 600 x 600mm without volume controldampers.

a 600 x 600mm (outer size) Nos 32

b 375 x 375mm neck size Nos 21

632 Supply and installation of Acoustic insulated plenum

boxes for supply air diffusers with 12mm thick, 48kg/Cu.m density fibre glass rigid board fasten to theplenum box with nuts and bolts.

375 x 375 - 450mm height Nos 24

633 Supply and installation of Powder coated extrudedaluminium continuous linear grilles with 0 degreedeflection without volume control damper for fresh airGrille.

Sqm. 3

634 Supply and installation of Powder coated extrudedaluminium continuous linear grilles with 0 degreedeflection without volume control damper forexhaust air Grille.

Sqm. 8

635 Supply and installation of Polypropylene or

Aluminium return air round diffuser with white finish.The cone is screwed a number of turns clockwise oranticlockwise so as to achive the air gap.150mm dia Nos 197

636 Supply and installation of Polypropylene orAluminium exhasut air round diffuser (for toilets) withwhite finish. The cone is screwed a number of turnsclockwise or anticlockwise so as to achive the air gap. (Dia150 mm)

Nos 48

637 Supply, installation and commissioning of combinedSmoke and Fire damper with actuator complete withfactory made 1.6mm thick GSS sleeves suitable for 90

minutes fire rating located in supply air ducts.In case offire failure the damper shall assume " closed posittion"(suitable for BAS) The motorised actuator to operate theabove fire damper on receipt of signal from DDC system/fire detection system.

Sqm. 3

638 Supply,Installation,Testing and commissioning offollowing: Actuator,temperature sensor and provision forreceipt of external fire signal, wiring as specifications.

Nos. 6

639 Supply and installation of Control panel for the above fire

damper (to be located near Fire damper in respectiveAHU/fan rooms Power supply to the fire damper panelsshall be provided from AHU/fan electrical panel. These

shall be interlocked/integrated with zonal damper statusindicating panels.

Nos. 6

640 Powder coated extruded aluminium air transfer (non

vision) door grilles comprising of front section withinverted „V‟ horizontal blades, borders, countersunk forscrew fixing, and matching rear side frame flanges.

Sqm. 2



641 Supply and installation of GI volume control damper lowleakage( wheel type ) made out of 1.6mm thick galvanisedsheet steel frame and opposed blades of 1.6mmgalvanised steel with suitable links, handles, levers andquadrants for manual control of volume of air flow andfor proper balancing of air distribution system.

Sqm. 10

642 Supply and installation of Non Return damper (lowleakage) made out of 1.6mm thick galvanised sheet. Sqm. 0.15

643 Supply, fixing, testing and balancing of Aluminiumpowder coated Fresh air and exhaust arrangement with

storm proof louvers, volume control damper, MS weldmesh bird screen / mounting frame - 100mm louverspacing and 45 deg angle suitable for protection againstsplashing rain water fixed within a right aluminiumframe.

Sqm. 49

644 Supply and erection of following sizes Ladder type cable

tray made out of 16G thick GI sheet folded to requiredshape with adequate number of supports forInsulated refrigerant pipe and cable conduits. The tray

shall be covered 16G GI sheet at terrace and whereverexposed.

a 150mm wide RMT 497

b 300mm wide RMT 717

c 450mm wide RMT 66

d 600mm wide RMT 63

e 900mm wide RMT 19

VIII VENTILATION SYSTEM

645 Supply, installation, testing and commissioning of cabinettype and Rectangular type ventilation fans consists of GSSrectangular cabinet, removable access door for easyaccessibility to motor and fan, flanged inlet and outlet for

easy duct work connection, thermally protected motorand necessary supports. Motors shall be suitable for 415+/- 10%v, 50Hz 3Phase & 230 +/- 10%V, 50Hz, 1 PhaseAC supply and the capacity are as follows. The fan shallbe located at terrace (Weather proof for outdoor type fansand no weather proof for indoor type fans)

a Air flow rate : 22800CFM (Outdoor type) Nos. 2External Static Pressure : 400 Pa

Fan type: Cabinet type fan

Indicative Fan motor : 11.0 kW

b Air flow rate : 14400CFM (Outdoor type) Nos. 2

External Static Pressure : 400 PaFan type: Cabinet type fan


c Air flow rate : 5550CFM Nos. 1External Static Pressure : 300 Pa



d Air flow rate : 5550CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa





e Air flow rate : 3450CFM Nos. 1External Static Pressure : 300 Pa



f Air flow rate : 2760CFM Nos. 2

External Static Pressure : 100 PaFan type: Rectangular ducted inline fan


g Air flow rate : 2550CFM Nos. 1External Static Pressure : 100 Pa

Fan type: Rectangular ducted inline fan


h Air flow rate : 400CFM (Outdoor type) Nos. 1External Static Pressure : 100 Pa



i Air flow rate : 510 CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa



j Air flow rate : 500 CFM Nos. 1External Static Pressure : 300 Pa



k Air flow rate : 700 CFM (Outdoor type) Nos. 2External Static Pressure : 300 Pa



l Air flow rate : 978 CFM (Outdoor type) Nos. 2External Static Pressure : 300 Pa



m Air flow rate : 1100 CFM Nos. 2External Static Pressure : 300 Pa



n Air flow rate : 1200 CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa


Indicative Fan motor : 0.55 kWo Air flow rate : 1400 CFM (Outdoor type) Nos. 3External Static Pressure : 300 Pa



p Air flow rate : 1580 CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa





q Air flow rate : 1800 CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa



r Air flow rate : 2150 CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa


Indicative Fan motor :1.1 kWs Air flow rate : 2400 CFM (Outdoor type) Nos. 1

External Static Pressure : 300 Pa


Indicative Fan motor :1.1 kW

t Air flow rate : 3184 CFM (Outdoor type) Nos. 1External Static Pressure : 300 Pa



u Air flow rate : 4800 CFM Nos. 4External Static Pressure : 300 Pa

Fan type: Cabinet type DIDWIndicative Fan motor :2.2 kW

646 Supply, installation, testing and commissioning of circularinline direct drive fan, wall mounted type complete withgravity louvers, motors, starter panels, powder coatedAluminium angle, mounting brackets, 5amps plug top,3mtr. flexible power cables, from nearby power outlets,motors shall be included for life ball bearing with internalautomatic reset safety thermal overload protection device,mounting supports and other standard accessories as perspecifications and suitable for operation 230 +/- 10%V,50/60Hz, 1 Phase AC supply.

a Air flow rate : 350CFM Nos. 1External Static Pressure : 100 Pa

Fan type: Circular ducted inline fan


b Air flow rate : 250CFM Nos. 1External Static Pressure : 100 Pa

Fan type: Circular ducted inline fan


647 Supply, installation, testing and commissioning ofpropeller type direct drive fan, wall mounted typecomplete with gravity louvers, motors, starter panels,powder coated Aluminium angle, mounting brackets,

5amps plug top, 3mtr. flexible power cables, from nearbypower outlets, 600x600x20mm thick marine plywood withhole to suit impeller dia, mounting supports and otherstandard accessories as per specifications and suitable foroperation 230 +/- 10%V, 50Hz, 1 Phase AC supply.

a Air flow rate : 2150CFM Nos. 2External Static Pressure : 100 Pa

Fan type: Propeller





Fan type: Propeller

Indicative Fan motor : 0.37kW

c Air flow rate : 250CFM Nos. 66External Static Pressure : 100 Pa

Fan type: PropellerIndicative Fan motor : 0.1 kW

d Air flow rate : 200CFM Nos. 28External Static Pressure : 100 Pa

Fan type: Propeller


e Air flow rate : 100CFM Nos. 189External Static Pressure : 100 Pa

Fan type: Propeller


648 Supply, installation, testing and commissioning of Roofextractor fan type complete with mild steel or galvanisedsteel mounted on a horizontal square base for cylindicalcasing, rain hood shall be made of fibre class as protectionagainst adverse weather conditions, impeller shall bemanually adjustable pitch blade made of powder coatedAluminium, gravity louvers, motors, starter panels, anglemounting brackets, 5amps plug top, 3mtr. flexible powercables, from nearby power outlets, mounting supportsand other standard accessories as per specifications andsuitable for operation 230 +/- 10%V, 50/60Hz, 1 PhaseAC supply.

a Air flow rate : 900CFM Nos. 2

External Static Pressure : 100 PaFan type: Roof extractor fan (Outdoor type)



Fan type: Roof extractor fan (Outdoor type)


649 MS additional supports for hanging all the indoor units kg 2450

IX ACMV RELATED ELECTRICAL ITEMS

650 Supply,erection,testing and commissioning of startercomprising of the following

1No. 16A TP&N MCB with adjustable variable settings 16KA with all connected accessories



1 No. DOL (3 Phase) suitable for 2.20KW for exhaust fanwith Ammeter, selector switch, suitable ratio ofCTs,control fuses, Auto/Manual selector switch,on/off/trip indication lamp with necessary power andcontrol wiring interconnections etc.,with suitableprovision to link with IBMS for remote operation and allconnected necessary accessories ina suitable MS enclosurewith painting , earthling and suitable fixing arrangementas required

Nos. 7

651 Supply,erection,testing and commissioning of startercomprising of the following1No. 63A TP&N MCCB with adjustable variable settings16 KA with all connected accessories.1 No. Star Delta starter (3 Phase) suitable for 7.5 KW forcabinet type fan with Ammeter, selector switch, suitableratio of CTs,control fuses, Auto/Manual selector switch,on/off/trip indication lamp with necessary power andcontrol wiring interconnections etc.,with suitableprovision to link with IBMS and all connected necessaryaccessories in a suitable MS enclosure with painting ,

earthling and suitable fixing arrangement as required.

Nos. 2

652 Supply,erection,testing and commissioning of startercomprising of the following1No. 32A TP&N MCB with adjustable variable settings 16KA with all connected accessories1 No. Star Delta starter (3 Phase) suitable for 7.5 KW for

AHU with Ammeter, selector switch, suitable ratio ofCTs,control fuses, Auto/Manual selector switch,on/off/trip indication lamp with necessary power andcontrol wiring interconnections etc.,with suitableprovision to link with IBMS for remote operation and allconnected necessary accessories in a suitable MS

enclosure with painting , earthling and suitable fixingarrangement as required

Nos. 1

653 Supply,erection,testing and commissioning of startercomprising of the following1No. 32A TP&N MCB with adjustable variable settings 16KA with all connected accessories1 No. DOL starter (3 Phase) suitable for 3.7 KW for HRW

with Ammeter, selector switch, suitable ratio ofCTs,control fuses, Auto/Manual selector switch,on/off/trip indication lamp with necessary power andcontrol wiring interconnections etc.,with suitableprovision to link with IBMS for remote operation and all

connected necessary accessories in a suitable MSenclosure with painting , earthling and suitable fixingarrangement as required

Nos. 2

654 Supply,erection,testing and commissioning of startercomprising of the following1No. 63A TP&N MCB with adjustable variable settings 16KA with all connected accessories.



1 No. Star Delta starter (3 Phase) suitable for 11.0 KW forexhaust air fan with Ammeter, selector switch, suitableratio of CTs,control fuses, Auto/Manual selector switch,on/off/trip indication lamp with necessary power andcontrol wiring interconnections etc.,with suitableprovision to link with IBMS and all connected necessaryaccessories in a suitable MS enclosure with painting ,earthling and suitable fixing arrangement as required.

Nos. 2

CABLE AND TERMINATION

655 Supply, laying of following cables

a 4 Core 6 Sqmm PVC Cu. Cable RMT 45

b 4 Core 4 Sqmm PVC Cu. Cable RMT 85

c 3.5 Core 50 Sqmm XLPE Arm.Cu. Cable RMT 20

656 Supply termination and commissioning of the followingsize cables with suitable double compression glands andcrimping socket with suitable earth clip & fixingaccessories.

a 4 Core 6 Sqmm PVC Cu. Cable Nos. 4

b 4 Core 4 Sqmm PVC Cu. Cable Nos 10

c 3.5 Core 50 Sqmm XLPE Arm.Cu. Cable Nos. 4

d 3 Core 2.5 Sqmm PVC Cu. Cable Nos 14

657 Supply and fixing of lockable type push button control forON / OFF

Nos 313

EARTHING

658 Supply, erection of following sizes GI Ladder type cablerack system made out of sheet steel folded to requiredshape with adequate number of supports.

The cable rack shall have runners rugs of suitable size,horizontal elbow, vertical elbow 90 Deg. Up verticalelbow 90 Deg. Down, re-deep, coupler plates, materials.

The cable racks shall be suspended from ceilingsupported from side walls in columns etc. with adequatesize supporting angles / channels with fastners, welding,anchor bolts, nuts etc. The rack shall have suitable cableclamping arrangements etc. The metal rack system shallbe treated with one coat of rubber based polyvinyl paintas primer and finished with two coats of green enamelpaint complete with all civil works for fabrication details

150 MM RMT 160Fire Protection System

659 DIESEL ENGINE DRIVEN PUMP



Supply, installation, testing and commissioning of dieselengine driven pump set as per specification.The engineshould have RPM between 1800 to 2100.The Pump shallbe horizontal end suction, top discharge mounted oncommon baseframe. Pump shall be directly coupled todiesel engine of suitable as per system design condition.Engine shall be complete with flywheel, spider coupling,Air cleaners, Water cooled,Heat Exchanger,CorrosionResistor,Oil Sump with lube at pump. Governor, FuelFilter,starting motor battery charging alternator &instrument panel suitable for 24 volt DC includingstarting switches, Diesel tank, lube oil temperaturegauge,lube oil pressure & high water temperatureincluding flexible exhaust connection.The pump shall becapable to delivery 171m3/hr. at 120 m head. 129KWapprox.

Set 1

660 MAIN ElECTRICAL DRIVEN FIRE PUMPSET

Supply, installation, testing, commissioning of electricallydriven pump set as per specification. Motor TEFC type,

2900 rpm, 415V, 50 cycle frequency 3 phase class „F‟insulation, I.P. 54 protection, starting on DOL. The Pumpshall be horizontal, end suction, top discharge. The pumpshall have cast iron casing, bronze impeller, steel shaftwith common base frame capable of discharging 171 m3per hour at 120 m head. 110KW approx.

Set 2

661 JOCKEY PUMPSET

Supply, installation, testing and commissioning ofelectrically driven pump set as per specification. MotorTEFC type, 2900 RPM 415 V, 50 cycles, 3 phase, class „F‟

insulation, IP 54 protection, 20 HP(Indicative) starting onDOL. The Pump shall be Vertical Inline Pump. The pump

shall have cast iron casing, Cast iron impeller, steelshaft.with common base frame capable of discharging10.8 m3/hour at 120 m head.

Set 1

662 MOTOR CONTROL CENTRE (MCC PANEL)

Supply installation testing and commissioning ofsectionalised cubicle type floor mounted front operateddust and vermin proof power cum control panel made outof not less than 1.6mm MS sheet with enamelled finishi/c. one coat of primer of approved shade and colour i/c.providing suitable number of switchgears, busbars,auxilliary switches, audio alarm hooters, visual

indications, relays, contactors, timers of suitable capacityfor automatic operation of pumps i/c. connections alongwith provision to link with IBMS and all connectedaccessories.Panel should be powder coated, Indicatinglamps should be of LED type as per the Single linedia ram.Outgoing



100/125A TP&N MCCB 25 KA with fully automatic DOLStarter suitable for jockey pump with ON/OFF/TRIPindicating lamps,ON/OFF push buttons and all otherrequired accessories -1No 100/125A TP&N MCCB 25 KAwith fully automatic star delta starter suitable for boosterpump with ON/OFF/TRIP indicating lamps ,ON/OFFpush buttons and all other required accessories -3Nos.400A TP&N MCCB 25 KA with 150 HP fully automaticDOL starter with ON/OFF/TRIP indicatinglamps,ON/OFF push buttons and all other requiredaccessories-2Nos. 32A TP&N MCCB 25 KA with all otherrequired accessories with one set of ON/OFF/TRIPindicating lamp with protective fuses-1No With necessaryAluminium busbars,interconnections,earthing etc.,withrequired accessories as per specifications.

No. 1

663 DIESEL ENGINE AUTO START PANEL

Supply and installation of Autostart panel for the dieselengine complete with auto/manual switch, LED

indication lamps, protective fuses with Electronichooter,Electronic timer,plug in relay,Push buttons,voltmeter,ammeter,Bridgerectifier,Choke,OFF/AUTO/MANUAL selectionswitch,TRICKLE/BOOST selection switch,ON/OFFselection switch, battery charger, suitable of working on230 V, AC, single phase, enclosure being vermin & dustproof. Also potential free contacts shall be provided forconnecting to the building automation system. Automaticstarting by means of a battery powered electric startermotor incorporating the axial displacement type ofpinion, having automatic repeat start facilities initiated bya fall in pressure in the water supply pipe to the sprinkler

and/or hydrant installation. The battery (lead acid orNickel-Cadmium) capacity shall be adequate for tenconsecutive starts without recharging with a cold engineunder full compression.Panel should be powder coated,Indicating lamps should be of LED type.Panelconstruction shall be 14SWG M.S sheetbolted/welded..Wiring shall be of 1.5 Sq.mm PVCinsulated stranded copper conductor.

Set 1

664 CABLES:

Supply, laying, testing and commissioning of thefollowing sizes of cables on surface of wall or cabletraearth clip & fixing Accessories

a 2 core X1.5Sq.mm PVC copper armoured cable RMT 30

b 3 core X1.5Sq.mm PVC copper armoured cable RMT 30

c 4 core X1.5Sq.mm PVC copper armoured cable RMT 30

665 CABLE TERMINATION :

Supply terminatin & commissioning of following cableswith double compression glands & crimping typeAluminium lugs with suitable earth clip & fixingAccessories

a 2 core X1.5Sq.mm PVC copper armoured cable Nos. 2



b 3 core X1.5Sq.mm PVC copper armoured cable Nos. 2

c 4 core X1.5Sq.mm PVC copper armoured cable Nos. 6HYDRANT SYSTEM

666 Supply, installation, testing & commissioning ofelectrically driven pumpset as per specification. MotorTEFC type, 2900 RPM, 415 V 50 cycle, 3 phase Class 'F"insulation, IP - 55 protection, 10 HP starting on DOL. The

Pump shall be horizontal, end suction, top discharge. Thepump shall be cast iron casing, bronze impeller, steelshaft. with common base frame capable of discharging 27m3/hour at 45 m head. Pump to be installed at Terrace.

Nos. 4

667 Supply and instalation of Cast Iron Sluice Valve, as perIS:14846 with necessary flanges

a 300 NB, PN.16 Nos. 2

b 200 NB, PN.16 Nos. 5

c 150 NB, PN.16 Nos. 25

d 100NB PN.16 Nos. 2

e 80 NB, PN.16 No. 1

668 Supply and installation of Cast Iron Butterfly isolationvalve with necessary flanges, supports, bolts, nuts, etc

a 150 NB Nos. 16

b 100 NB Nos. 4

c 65 NB Nos. 14

d 50 NB Nos. 7

669 Supply, erection, testing and commissioning of gunmetalgate valve with necessary flanges, supports, bolts, nuts,etc & (Below 50NB) screwed ends

a 50 NB Nos. 11

b 40NB Nos. 49

c 20NB Nos. 7

670 Suplying & installation of Cast Iron Non-Return Valves(Normex make) including making flanged joints byproviding necessary nuts, bolts, gaskets etc. All completeas per specifications.

a 200 NB No. 1

b 150 NB Nos. 16

c 65 NB No. 3

d 50 NB No. 4

671 Under Ground piping - Supply, erection, testing andinstallation of MS pipes conforming to IS 3589 for 200NB& above and IS 1239 for 150NB & below with welded

joints including cutting the pipes to correct length,providing and welding flanges to pipe, fixing with clampsto MS brackets/ hangers, making flanged joints withnecessary nuts, bolts, gaskets,. blank flanges, etc. Ratesincluding 10% radiograph all complete as perspecifications of the following diameters.

a 200 NB - Class C RMT 580

b 150 NB - Class C RMT 1198



c 80 NB - Class C RMT 37

672 Supply, erection, testing and installation of MS pipesconforming to IS 3589 for 200NB & above and IS 1239 for150NB & below with welded joints including cutting thepipes to correct length, providing and welding flanges topipe, fixing with clamps to MS brackets/ hangers, makingflanged joints with necessary nuts, bolts, gaskets,. blankflanges, etc. Rate shall be inclusive of Zinc chromateprimer over that 2 coats red enamel panit as per Fireauthorities requirement over all above ground pipes.

a 400 NB -8mm thick RMT 9

b 300 NB -8mm thick RMT 4

c 200 NB -6.35mm thick RMT 19

d 150 NB - Class C RMT 174

e 100 NB - Class C RMT 178

f 80 NB - Class C RMT 38

g 65 NB - Class C RMT 93

h 50 NB - Class C RMT 73

i 40 NB - Class C RMT 31673 Supply, installation, testing and commissioning ofcourtyard Gun metal Single headed hydrant as per IS:5290 consisting of 63NB single outlet flanged oblique typehydrants valve with instantaneous female plunger typecoupling, chained blank cap including making flanged joints by providing necessary nuts, bolts, gaskets allcomplete as per specifications suitable for 80 NB stand

ost.

Nos. 26

674 Supply & installation of RRL type-A hose reel of 63mmdia. x 15metres long with heavy quality gun metal malecoupling of IS: 903. combined with 2 Nos of Canvasshoses and 2 Nos of nozzles with ms painted hose tray to

accommodate hose reel

Nos. 26

675 Supply & installation of fabricated MS sheet of size750x600x250 with glass fronted door, painted in red outside and white in inside, hose boxes along with GIsupport angles for courtyard hydrants. Each box shall becapable to accommodate 2 hose each of 63 mm dia x 15 mlong hose pipe, nozzle, branch pipe etc.

Nos. 26

676 Supply, installation, testing and commissioning of 63mmdia. approved make GM double headed fire hydrantlanding valves (with instantaneous female plunger typecouplings, chained blank caps) including making flanged joints by providing necessary nuts, bolts, gaskets, etc.painting complete as per specifications.

Nos. 21

677 Supply, installation, testing and commissioning of 63mmdia. approved make GM single headed fire hydrantlanding valves (with instantaneous female plunger typecouplings, chained blank caps) including making flanged joints by providing necessary nuts, bolts, gaskets, etc.painting complete as per specifications.

Nos. 54



678 Supply & installation of RRL type-A hose reel of 63mmdia. x 7.5metres long with heavy quality gun metal malecoupling of IS: 903. combined with 2 Nos of Canvasshoses and 2 Nos of nozzles with ms painted hose tray toaccommodate hose reel

Nos. 75

679 Supply & Installation of drum type wall mounting hosereels, swiveling 180o consisting of 25 mm dia. x 30metreslong armored rubber hose pipe with 15 mm dia. bronzeshut of type jet nozzle & cut-off valve on the inletincluding making connection to the wet riser, by drillingwelding, fixing the hose reel to the wall by providingnecessary anchor fasteners/ expansion bolts, grouting thesame with cement mortar, painting all complete as perdrawings, specifications.

Nos. 75

680 Supply and fixing of fire shutter fabricated out ofanodised aluminium sheet and frame,door shall be900mmx1500mm & fixed with 4mm thick class,suitablerubber beeding and locking arrangement.Rate shall beincludes all fateners etc, and complete shutter shall be

powder coated of approved colour both inside andoutside.

Nos. 55

681 Supply & installation of Siamese inlet (Fire Brigade inlet)connection with provision for Four male instantaneouscoupling fabricated out of 150 mm dia. approved makeheavy class MS pipe with nonreturn valve, for firefighting system including making connection byproviding necessary piping & fittings to the fire storagetank, fire fighting wet riser, sprinkler system painting thesame with 3 coats of enamel paint over a coat of ZincChromate primer all complete as per drawings,specifications.Connection to Fire Tanks / Yard Hydrants

Nos. 13

682 Supply and wrapping of Coating & Wrapping Materialsmanufactured as per IS 10221 (make:Pypkote) 4mm thickfor underground Pipes as per specification Steel pipelinesto be laid underground buried in the soil shall beprotected against corrosion by means of coating &wrapping as per IS:10221.The above coating andwrapping shall be carried out in systematic manner suchthat uniform thickness of coating is obtained as per ISspecification.Buried pipelines shall be laid in general withtop of pipe 1(one) metre below the ground level. Wheresoil conditions are not satisfactory, masonry or equivalentsupports shall be provided at regular intervals. The rateshall be inclusive of holiday test of undergorund pipes.

Sqm. 965

683 Orifice plate made out of stainless steel 5mm thick

80 NB dia Nos. 26

684 Electronic level indicator with pressure transducer sensorsED display high / low level / cabling to pumphouse withindicators etc.,

Set 1



685 Supply & installation of 1 No Differential Pressure switchwith 1No 150dia dial pressure gauge in 150dia manifold,Bronze check valve with 2mm Orifice, Stainless Steelpresssure sensing piping 15mm dia required length asshown in drawing.

Nos. 7

SPRINKLER SYSTEM

686 Supply, erection, testing and installation of heavy (classC) black steel pipes conforming to IS 1239 with welded joints including cutting the pipes to correct lengths, fixingwith clamps to MS brackets / hangers, steel supports,hitec supports as per drawing. The hydro testing shall be

done at 18 kgs/cm2 pressure. Rate shall be inclusive ofZinc chromate primer over that 2 coats red enamel panitas per Fire authorities requirement over all above groundpies.Rates to inclusive of all complete as per specifications(including heavy class forged fittings of IS standards) ofthe following diameters.

a 150 NB - Heavy Class RMT 353

b 100 NB - Heavy Class RMT 123

c 80 NB - Heavy Class RMT 385d 65 NB - Heavy Class RMT 590

e 50 NB - Heavy Class RMT 1515

f 40 NB - Heavy Class RMT 349

g 32 - Heavy Class RMT 849

h 25 - Heavy Class RMT 3642

687 Supply and installation of Cast Iron Butterfly isolationvalve with necessary flanges, supports, bolts, nuts, etc

a 150 NB Nos. 20

b 100NB Nos. 4

c 80NB Nos. 19

d 65NB Nos. 6e 50NB Nos. 4

688 Supply, erection, testing and commissioning of gunmetalgate valve with necessary flanges, supports, bolts, nuts,etc. (Below 50NB) screwed ends

a 50NB Nos. 32

b 40 NB. Nos. 16

c 20 NB. Nos. 7

689 Supply & installation of 20 NB CI Automatic Air ReleaseValve to all Sprinkler risers all complete as perspecifications.

Nos. 9

690 Supply and installation of Pendant type Sprinkler head

with the following temperature rating & respond,universal deflector, chromium finish as per specifications.Size: 15-mm dia. The rate shall be inclusive of Stainlesssteel Rossette plate in office area and other false ceilingareas. Temperature Rating: 68°C Standard respond

Nos. 693



691 Supply and installation of Upright Sprinkler head withthe following temperature rating & respond, universaldeflector, chromium finish as per specifications. Size: 15-mm dia. Temperature Rating: 68°C Standard respond

Nos. 930

692 Supply and installation of Side wall type Sprinkler headwith the following temperature rating & respond,universal deflector, chromium finish as per specifications.Size: 15-mm dia. Temperature Rating: 68°C Standardrespond.

Nos. 690

693 Supplying & installing of approved make flow switches

(flow sensors) suitable to be fixed directly on line of thefollowing diameters, with 1 NO & 1 NC potential freecontacts.

a 150 NB Nos. 7

b 100 NB Nos. 2

c 80 NB Nos. 16

d 65NB Nos. 3

694 Supply, erection, testing and commissioning of Metallic

stainless steel (SS 304) corrugated or braided Flexible

drop pipes of 25mm dia with cross bar assembly supportsuitable for grid ceiling, reducing fitting, special shoulderNipple, redcing nipple, T bar braket, braket clip assembly.(Make:TYCO / Flex Head / Viking)

1200 mm Nos. 683

695 Supply & installation of Instrument cables for flowswitches to annunciator panel The cable should be 2 corex 1.5 Sq.mm copper armoured cable. Complete as perspecification.

RMT 8833

696 Supply & installation of sprinkler annunciator panelconsisting of 40 windows, capable of working on 230 V

AC single phase supply and provided with battery back-up of 24 V complete as per specification. Each windowsshall be provided with potential free contact forconnecting to the BMS system

Lot 1

697 Supply, installation, testing and commissioning of waterflow will activate a hydraulic powered water motor alarmby way of integral valve alarm line trim piping. Watermotor gong shall be connected to a water pressureretarding chamber to limit the propensity of unnecessaryalarms. Water motor alarm shall be equipped with a rearclosure plate to limit the access of foreign materials ofaccumulation of debris.Size of alarm valve shall be200NB.

No. 1

698 PORTABLE FIRE EXTINGUISHERS:

Supply & installation of following Portable FireExtinguisher :

a Carbon Dioxide Fire Extinguisher Nos. 102Capacity - 4.5 Kg

Type - Upright

IS - 15683

b ABC Fire Extinguisher Nos. 124Capacity - 5 Kg



Type - Upright

IS - 15683

c DCP Type Extinguisher Nos. 20Capacity - 9 Kg

Type - Upright

IS - 15683

699 Supply and installation of Fire buckets of 9 ltrs capacity.

Stand made of MS Channel and angle to accommodate 4Nos of buckets filled with cleaned soft sand. Rate shall beinclusive of red paint as per Fire Codes for buckets andMS Stand.

Nos. 5

IBMS works

FIRE ALARM SYSTEM.

700 Supply, installation, testing and commissioning of thefollowing system as per the technical specification.

Analogue addressable micro Process - controlled FireAlarm Control Panels, capable of being IP networked tothe central monitoring System, to monitor and integratedthe following quantity of accessories like detectors,MCP's/hooters/control modules, Fault IsolationModules, hooters, response indicators, fire/faultindicators, audiovisual signals, central processing units,complete with LCD display, zone indicating LEDs as perthe detailed specification: complete with Battery backupwith charger for each panel. Each loop should providedwith minimum 125 detectors /devices

a 8 LOOP PANEL No. 1

b 6 LOOP PANEL No. 1

c 1 LOOP PANEL Nos. 3Note: Providing Windows based graphical software,

(with necessary software addresses required as per BOQ)on MS windows 2000/XP or latest platform, includingAlarm Management for IBMS as per the above item

701 Rate of Rise Heat Detectors (Thermal Detectors):GRADE-IAddressable analogue type Heat Detectors with solidstate design with sensing element combination of fixedtype and rate of rise of temperature indicating LED,mounting base etc. as per detailed specifications.(wallmounted type)

Nos. 568

702 Addressable analogue MUTISENSOR type smokedetectors with dual chamber, solid state design, indicatingLED, mounting base etc. as per detailed specification. Therate shall inclusive of necessary base box, connecting gladfor above detectors(ceiling, false ceiling, direct ceiling &false flooring mounted type)

Nos. 767

703 Duct detector suitable for providing the return air pathwith suitable fixing accessories

Nos. 20

704 Hooter with relay module and strobe light with minimum85 db audible and control relay module, power supplyunits etc

Nos. 96



705 Manual call points pull stations of approved make withNO/NC contacts slim type and projecting out from thesurface of enclosure with glass suitable for addressablefunction

Nos. 108

706 Fault isolation module to electrically isolate differentsections of detector loops.

Nos. 79

707 Addressable control module to trip the AHU,s, Accessdoor, triggering the DVR.lift landing etc

Nos. 24

708 Addressable monitor module along with door contact forFire doors & Beam detector

Nos. 25

709 Response indicator for mounting on false ceiling at theentries of the cabin for indicating the operation fordetectors in the above areas.

Nos. 342

710 2C 1.5 armoured copper FRLS cable in ceiling withsuitable clamps and screws (RED colour)

RMT 16000

711 Wall mounted type Beam detector with receiver coverageof minimum 25 mtr distance as per detailed specifications.

The adjustable angle shall be +/- 10o for both vertical andHorizontal. The detector should be capable of connectingto existing Addressable fire alarm panel.

set 4

712 Wiring to the detectors/devices using 2C x 0.75 sq mmPVC insulated flexible copper conductor (FRLS) insuitable size PVC pipe in concealed system in thefloor/ceiling with all accessories likebends,elbows,junction boxes, clamps, GI flexible hose etc.,

RMT 10000

713 Repeater panel as per the specification (Suitable for abovefire panel loop). The rate shall be inclusive of all powersupply units, LCD display etc.,

No. 1

II PUBLIC ADDRESS SYSTEM AND EVC SYSTEM

Supply, installation, testing and commissioning of the

following system as per the technical specification.

714 System Controller complete with 12 Zone Call Station,Stem Type Microphone, 2 mm thick CRCA Sheet PowderCoated Rack, Dual Tone Control for Speech & Music,integration facility with Fire Alarm System, tonegenerator & Speech Processor with relays for activatingtone & pre-recorded fire alarm messages, facility tointegrate with the base builder P.A System as specified inthe Tender Specifications . The rate inclusive of Prioritymodule, selector switch etc

No. 1

715 42U floor mounted rack frame made out of powder

coated materials with ventilation louvers in back sideprovided with glass door in front side. The rack shall beprovided with suitable power sockets/strips, ventilationtray fans, horizontal cable manager, bottom wheel etc

No. 1

716 20 W Wall/Column Mounted Speakers with linematching transformers and selected able tap setting asspecified in the Tender Specifications

Nos. 31



717 6 W Wall Mounted Speakers with line matchingtransformers & selected able tap setting as specified in theTender Specifications for electrical rooms and AHU rooms

Nos. 19

718 6 W Ceiling Mounted Speakers with line matchingtransformers & selectable tap setting as specified in theTender Specifications for false ceiling areas.

Nos. 290

719 Rack Mounted minimum 480 W Power Amplifier asspecified in the Tender Specifications

Nos. 3

720 Rack Mounted minimum 240 W Power Amplifier asspecified in the Tender Specifications

Nos. 6

721 2 core twin twisted 48/0.2 ATC, Multi strand, over allarmoured speaker cable as specified in the TenderSpecifications

RMT 12500

722 Micro phone unit with back box, STAND LEGNTH OFCABLES

No. 1

723 1 No. each of AM/FM Tuner, DVD player withoverriding facility, Music Source Selector, with assignablepriority on each channel to accept Music, Telephone,Microphone, Recorded message from Voice recorder etc.,

with in-built compressor and limiter.

Nos. 1

724 Auto dialer for interfacing with Fire alarm system Nos. 1

725 12 Zone Auto speech processor (Digital Voice Recorder)for fire activation message

Nos. 1

III ACCESS CONTROL SYSTEM



726 Access control system complete with necessary hardware,Software etc., as specified for centralized securitymonitoring. Supply, installation, testing andCommissioning of the following system as per thetechnical specification.Access Controllers, each with capacity of 10000 eventsbuffer memory connecting the the item listed belowsuch as card readers, Magnetic locks, boom barriers etc

a 2 reader controller (1 set of single door) Nos. 14

b 2 reader controller (1 set of double door) Nos. 9

c 4 reader controller (1 set of single door+1set of doubledoor)

No. 1

d 4 reader controller (2 set of Tripod Turnstile) Nos. 4

e 6 reader controller (3 sets of single door) No. 1

f Smart Card readers with stainless steel base plate Nos. 72

g Biometric Card readers with stainless steel base plate Nos 1h Electromagnetic Locks - Single Door Nos 18

i Electromagnetic Locks - Double Door Nos 10

j Magnetic Contact Nos 38

k Emergency push button (glass type) Nos. 28FRLS shielded Cables:

727 Cable from electromagnetic lock/Sensor toController - 1Sqmm 4 C sqmm multi standarmoued shilelded cable

RMT 2650



728 Cable from Reader to Controller - 1 Sqmm 6 C sqmmmultistand shielded armoured cable

RMT 6300

729 Network cable for controller to controller -Armoured cable

RMT 2000

730 Access management software with time and attendancemodule suitable for flexi time report regeneration as perclient requirement with SQL /Oracle data base.

No. 1

731 Smart Card with holder, Lanyard, Adhesive labels forprinting the ID card

Nos. 500

732 Visitors management software as per technicalspecification and system PC comprising Intel core T2 Duo2.8 Ghz Processor @ L2 Cache 3 MB Intel 31 PR motherboard, 2GB DDr2 RAM @ 667 Mhz , 250GB HDD SATALogitech Keyboard, Logitech Optical mouse, ATX P IVCabinet with SMPS Prime Source, DVD Writer, Creative2.1 Speaker with Window NT/2000 operating system.(Main server - HOT Stand by / Parallel reduendancymode) .The system should be supplied with 21" TFT ColorMonitor.- Also, the PC shall be supplied with Web

Camera for taking the visitor photos.

No. 1

Boom Barrier

733 4.5Mtr. Rising Boom Barrier of as per the specificationcomplete with control unit and accessories, for Four wheelvehicle entry. The rate shall includes supply andproviding of necessary safety loop coil, pedestal for fixingthe Card reader in suitable height with weather proofarrangements.

Nos. 4

734 4.0Mtr. Rising Boom Barrier of as per the specificationcomplete with control unit and accessories, for Four wheelvehicle entry. The rate shall includes supply andproviding of necessary safety loop coil, pedestal for fixing

the Card reader in suitable height with weather proofarrangements.

Nos. 2

735 3.5Mtr. Rising Boom Barrier of as per the specificationcomplete with control unit and accessories, for Twovehicle entry. The rate shall includes supply andproviding of necessary safety loop coil, pedestal for fixingthe Card reader in suitable height with weather proofarrangements.

Nos. 5

736 2.5Mtr. Rising Boom Barrier of as per the specificationcomplete with control unit and accessories, for Twovehicle entry. The rate shall includes supply andproviding of necessary safety loop coil, pedestal for fixingthe Card reader in suitable height with weather proofarran ements.

Nos. 4

Stainless steel Tripod barriers

737 Tripod Turnstile with stainless steel with electric operatedhorms (motorized) as per the detailed specificationattached

Nos. 7

738 Swing gate for Handicap line No. 1

739 Full height Turnstile with stainless steel with electricoperated horms (motorized) as per the detailedspecification attached

No. 1



740 Booster antenna with pole to activate the RFID tag locatedat security gate

Nos. 36

741 50mm dia & 1.2 mtr height SS pole for Reader & Egressswitch fixing

Nos. 20

742 13.56 MHZ contact less smart Tag with Adhesive back. Nos. 200

IV CLOSED CIRCUIT TELEVISION SYSTEM



743 Colour 1/3" fixed dome indoor camera , 540 TV linesresolution and minimum lux level not more than 1.2 lux(F1.2) including all mounting supports / brackets andfixing accessories.

Nos 12

744 Colour 1/3" fixed dome outdoor camera , 540 TV linesresolution and minimum lux level not more than 1.2 lux(F1.2) including all mounting supports / brackets andfixing accessories.

Nos 8

745 Color high speed 1/4" Pan/Tilt/Zoom indoor camera, 540TVL (PAL)lines resolution and minimum lux level not

more than 0.05 lux at F1.2 with 23X optical or bettermotorized zoom lens, receiver, driver, Pan/Tilt andnecessary mounting support / bracket, accessories asrequired for indoor installation. and mounting support as

er s ecification.

No. 1

746 Color high speed 1/4" Pan/Tilt/Zoom outdoor camera,480 TVL (PAL)lines resolution and minimum lux level notmore than 0.05 lux at F1.2 with 23X optical or bettermotorized zoom lens, receiver, driver, Pan/Tilt andnecessary mounting support / bracket, accessories asrequired for outdoor installation along with standardoutdoor enclosure with suitable accessories and mountingsupport as per specification.

Nos 16

747 Power Supply Unit fixed cameras-12V Nos 20

748 DC/AC Power supply unit as required for the PTZcameras-24V

Nos 17

749 16 Channel Duplex Digital Video Recorder formultiplexing and digital recording , suitable for liveviewing and playback while recording , Motion detection,alarm event detection with TCP / IP connectivity - Harddisc ca acit 4TB

Nos 4

Cables:

750 RG 11Coaxial armoured Cable RMT 12600

751 2 Core 1.5 Sqm Twisted pair Shielded armmoured FRLS

cable for PTZ operation

RMT 5000

752 6 Mtr height GI post with necessary mounting bracket,weather proof box and Civil works for external cameras.

Nos 22

753 Mounting bracket with accessories for external cameramounted at terrace .

Nos 3



754 Excavation of ground to a depth of 3' level and width of1.5' and refilling etc.for laying the RG 11Coaxial armouredCable with PTZ operation cable and power cable. Extraearth after re-filling to be leveled in low lying area asdirected by the Engineer-in-charge .

RMT 5000

IP CAMERA

755 Integrated IP Colour 1/3" fixed dome indoor camera , 540TV lines resolution and minimum lux level not more than1.2 lux (F1.2) including all mounting supports / bracketsand fixing accessories.(Inclusive of POE)

Nos 36

756 Integrated IP Color high speed 1/4" Pan/Tilt/Zoomindoor camera, 540 lines resolution and minimum luxlevel not more than 0.05 lux at F1.2 with 23X motorizedzoom lens, receiver, driver, Pan/Tilt and necessarymounting support / brackets and fixing accessories as perspecification. (Inclusive of POE)

No. 1

757 DVM Dual core Server suitable to connect max. 100cameras with 5 User License. The rate shall inclusive ofnecessary software etc (1+1 ) configuration. The rate shall

inclusive of necessary storage server, processor server etc.,

Nos 1

758 Supply, fixing, testing and commissioning of CAT -12 portswitch and patch panel, connected accessories

Nos 4

759 Supply and fixing of Single I/O face plate with RJ 45connectors with suitable base box

Nos 80

760 9 U wall mounted rack with socket provision, powerchard

nos 4

761 Video streamer card for connecting the cameras -singlecamera streamer card. The rate shall inclusive of enclosurebox, power supply, filter board, gland etc

nos 8

V NOVEC GAS BASED SUPRESSION SYSTEM

(SERVER ROOM)

Supply, installation, testing and commissioning of thefollowing system as per the technical specification.

762 120 Ltrs. Cylinder with Valve for Server Room Nos 6

763 Novec gas kgs 550

764 Primary Completer Kit complete with Solenoid & Gaugeassembly, Discharge Tube, Manual Pneumatic Actuator,Flex Hoses, Warning Sign, Nameplate and Connectors.

No. 1

765 Slave completer Kit complete with Discharge Tube, FlexHoses, Pressure Gauge, Elbows and Connectors.

Nos 6

766 Check Valve Nos 6

767 Nozzles Nos 14768 Manifold No. 1

769 Rack - Wall Mount Kit Nos 12

770 M.S. Seamless pipes as per ASTM A 106 Gr. B, schedule 40with necessary fittings.

No. 1

771 Gas Release Panel with Battery Backup as Detection &Control equipment as per detailed technical specificationsfor Gas Suppression system

No. 1



791 2c x 1.0 Sq.mm copper conductor PVC insulated cable in25 mm Dia MS Conduit

RMT 150

IX INTERGRATED BUILDING MANAGEMENT SYSTEM

AND BUILDING MANAGEMENT SYSTEM:



BAS SERVER

792 Microprocessor based Integrated Building ManagementSystem as per the detailed specifications for complete andsatisfactory operation and control and to local authorities‟

approval. Main stations and subsystems with LAN,complete with hardware and software to providegraphical users interface consisting of System PCcomprising Intel core i 7 Ghz Processor , 4GB DDr2 RAM@ 667 Mhz , 500 GB HDD , Keyboard, Optical mouse,ATX P IV Cabinet with SMPS Prime Source, DVD Writer,Speaker with Window Latest operating system. Thesystem should be supplied with 21" TFT Color Monitor..Service pack XP-2 (Main server - HOT Stand by / Parallelredundancy mode) (1 set = 2 nos)

No. 1

GRAPHICAL SOFTWARE

793 Providing Windows based graphical software, (withnecessary software addresses required as per I/O list) onMS windows 2000/XP or NT platform, including AlarmManagement for IBMS as per the above item

No. 1

SOFT POINTS

794 Providing necessary Software and Hardware for

Interfacing through a gate way for monitoring throughserial Modbus interface for the data points for Chillers ,VFDs , VAVs, etc as per the detailed IO summary inHVAC tender . Total soft points 2500 pts includingenergymetres, UPS etc

Set 1

MONITORING STATION AND PRINTERS:

795 Monitoring station as per technical specification andsystem PC comprising Intel core T2 Duo 2.8 GhzProcessor @ L2 Cache 3 MB intel 31 PR mother board,4GB DDr2 RAM @ 667 Mhz , 250GB HDD , Keyboard,Optical mouse, external speakers, sound card ATX P IVCabinet with SMPS Prime Source, DVD Writer, Servicepack XP-2 with Window NT/2000 operating system. Thesystem should be supplied with 21" TFT Color Monitor.-1.FIRE & BMS PC (2-nos) 2. CCTV &ACCESS PC (2-nos)

Nos 4

796 Supply and commissioning of 600 DPI Colour InkjetPrinter

Nos 1

797 Supply and commissioning of Single A4 size Laser Printer No. 1

798 DIRECT DIGITAL CONTROLLER:



Autonomous networkable DDC Controller with 32 bitmicroprocessor based standalone and networkable typewith real time clock and historical database of min 1 Mbwith panels, peer to peer communicable DDC modules,input or output relays, terminal block, real time clock,networking and inbuilt data buffer for Followingrequirement as per Enclosed IO summary .

a DDC-TYPE A (Chiller) No. 1

b DDC-TYPE B (AHU) No. 1

c DDC-TYPE C (VRV unit) for OFFICE BLOCK No. 1

d DDC-TYPE D FOR REGIONAL STORE No. 1

e DDC-TYPE E FOR FIRE FIGHTING PANEL No. 1

f DDC-TYPE F FOR Bachelors & TransitAccommodation

No. 1

g DDC-TYPE G FOR TYPE C&D No. 1

h DDC-TYPE H (Electrical panel at substation) No. 1FIELD EQUIPMENT:

799 water level indicator for 3000 mm length Nos. 2

800 For Chiller

a Immersion type temperature sensor and thermowellacross the chiller pipe (Supply header, Return header,Supply header before bypass line and Return headerbefore bypass line) as per the system requirements forBAS system

Nos 4

b Differential-pressure transducer across the Chiller header(Supply & Return) as per the system requirements forBAS system

No. 1

c Flow sensor at chilled water flow as per the systemrequirements for BAS system

No. 1

d Ultrasonicmetre/BTUmetre as per the systemrequirements for BAS system

No. 1

e Pressure transducer across the Chiller header (Supply &

Return) as per the system requirements for BAS system

Nos 2

801 For AHU

a Immersion type temperature sensor in AHU CHW Inletpipe as per the system requirements for BAS system.

Nos 2

b Temperature (Supply & Return air) with necessaryaccessories to monitoring the conditioned areatemperature as per the system requirements for BASsystem

Nos 3

c RH Sensors (Supply & Return air) with necessaryaccessories to monitoring the conditioned area RH as perthe system requirements for BAS system

Nos 3

d Duct static pressure sensor to measure the static pressurein duct as per the AHU I/O listed for BAS system.

No. 1

e Differential pressure switch to monitor Filter & Fan statusas per AHU I/O listed for BAS system

Nos 3

f Flowmetre to measure the air flow of AHU at Plenum asper the AHU I/O listed for BAS system

No. 1

802 For TFA



a Temperature (Exhaust & Fresh air) with necessaryaccessories to monitoring the conditioned areatemperature as per the system requirements for BASsystem

Nos 4

b Differential pressure switch to monitor Filter & Fan statusas per TFA I/O listed for BAS system

Nos 7

c outdoor Temperature sensor No. 1

d Flowmetre to measure the air flow of AHU at Plenum asper the TFA I/O listed for BAS system

Nos 1

e Immersion type temperature sensor in AHU CHW Inletpipe as per the system requirements for BAS system.

No. 1

803 Software for facility management system with nessaryhardware accessories

set 1

CABLES / WIRES FOR IBMS

804 2 Core 1.0 sq. mm, armoured Annealed Tinned Copperconductor multi stranded Unscreened cable. [For ON /OFF Command & various status, Supply for FieldDevices]

RMT 7000

805 2 Core 1.0 sq. mm, armoured Annealed Tinned Copper

conductor multi stranded, screened cable. [For Sensors]

RMT 2000

806 4 Core 1.0 sq. mm, armoured Annealed Tinned Copperconductor multi stranded, screened cable. [For Sensors]

RMT 500

807 bus cable to intergate all DDCs, BTUmetres, VAVs etc -Armoured

RMT 2800

X MISCELLANEOUS ITEMS



808 150 mm wide size slotted angle GI ready made cable trays

of 14 SWG GI sheet. The rates for installation shallincluding necessary anchor fasteners and 'L' anglesupports @ 600mm interval etc., to suit site conditions asrequired all complete as directed by Engineer-Incharge.

RMT 1750

809 300 mm wide size slotted angle GI ready made cable traysof 14 SWG GI sheet. The Quoted rates for installation shallincluding necessary anchor fasteners and 'L' anglesupports @ 600mm interval etc., to suit site conditions asrequired all complete as directed by Engineer-Incharge.

RMT 1000

810 6 A 3-Pin Socket mounted on PVC Box which has to befixed in wall as required. The Socket should be of modular

type etc all complete as directed by Engineer-Incharge.

Each 110

TOTAL AMOUNT

(Rs.

Rebate

Final amount



Rate Amount

4758 49,573,602

5556 34,502,760

7432 10,256,160

x ens on, enna - ,



-

-

303517 1,517,585

531155 2,655,775

834671 834,671

168 1,476,048

168 34,104

131 144,100

131 72,050

155 85,250

155 85,250

181 80,907

181 199,100



1106 10,936,128

2151 1,600,344

1019 11,555,460

131 471,600 204 1,525,512



160 818,400

4847 2,040,587

5184 1,088,640

5683 4,245,201



8532 37,975,932

8532 3,378,672

8532 827,604 8590 13,116,930

8590 12,696,020

8590 10,806,220

8590 9,680,930

8590 3,676,520

8590 2,559,820

8615 2,567,270

8615 2,567,270

8615 2,567,270

8615 2,567,270

8615 2,567,270

8615 2,567,270 8615 2,584,500

8615 1,766,075

8615 1,679,925

8615 1,679,925

8657 1,688,115

8657 1,714,086

8657 1,056,154

8657 657,932



8657 588,676

3533 2,543,760

3290 1,246,910

1772 3,492,612



77790 227,535,750

532 5,277,440

566 12,852,728

584 24,970,088

584 2,130,432

138 1,539,114



4727 4,282,662

4710 273,180

4710 188,400

4710 155,430

4710 155,430

4710 155,430

4710 164,850

4748 166,180

4748 166,180

4748 166,180

4748 166,180

4748 166,180

4786 167,510

4786 124,436

4786 124,436

4786 124,436

4786 124,436

4823 144,690

4823 62,699

4823 72,345

1289 242,332

1380 2,565,420

1380 1,259,940

1380 1,346,880



1380 897,000

1380 527,160

832 20,800

832 10,816

832 37,440

832 29,120

7788 903,408

727 53,798

727 26,899

727 12,359

727 12,359

727 12,359

727 12,359



749 12,733

749 12,733

749 12,733

749 12,733

749 12,733

757 12,869

757 12,869

757 12,869 757 12,869

757 12,869

765 17,595

765 6,885

765 18,360

1618 3,135,684



1618 2,567,766

1618 1,475,616

1618 1,203,792

1618 1,203,792

1618 1,219,972

1663 1,253,902

1663 1,253,902

1663 1,253,902 1663 1,253,902

1663 1,253,902

1678 1,265,212

1678 1,137,684

1678 817,186

1678 682,946

1678 682,946

1693 858,351

1693 509,593

1693 433,408

1693 443,566 1693 546,839

1017 29,493

1017 291,879

1017 310,185

1017 310,185

1017 310,185

1017 285,777

1062 298,422

1062 298,422

1062 298,422 1062 298,422

1062 298,422

1077 302,637

1077 298,329

1077 298,329

1077 298,329

1077 298,329

1092 366,912

1092 125,580

1092 109,200

1092 3,276



258 4,601,946

193 951,297

122395 31,822,700

105779 4,442,718



108053 3,241,590

100252 6,015,120

4898 352,656



1190 506,940

2099 1,288,786

598 7,011,550

1622 1,523,058



104520 376,272

561 1,818,201

497 623,735

829 644,133

937 669,955



849 983,142

194 5,083,576

378 30,857,652

34 399,194

609 4,285,533



609 392,805

436 3,513,288

436 3,513,288

673 2,756,608



1206 280,998



1206 2,314,314

1206 1,439,964



1357 823,699

1055 2,527,780



3014 7,851,470



3014 7,227,572

7158 5,339,868



641 1,995,433

603 300,294



528 5,280

679 6,790

829 8,290

980 9,800

-

1131 11,310

1281 12,810

1357 13,570

1890 18,900

-

2035 20,350

2261 22,610

2562 25,620

2939 29,390

-

2788 27,880

2939 29,390

3165 31,650

3466 34,660 -

3014 30,140

3316 33,160

3768 37,680

4521 45,210

543 54,300



-

22603 678,090

-

7535 241,120

11 330,000

-

16 16



31 31

46 46

76 76

-

15069 15,069

1131 159,471

15069 587,691



189 9,450

-

12243 122,430

16952 830,648

957 834,504

-

905 371,050



1884 2,492,532

24110 1,591,260

14 165,312



1802 6,384,486

2266 5,352,292

5375 6,347,875

7059 12,501,489



955 3,132,400

1002 2,797,584

140 253,120



6996 4,715,304

3901 429,110

4198 155,326



2799 780,921

122885 122,885

22422 3,139,080

874494 874,494



11614 2,218,274

13992 111,936

16791 67,164



6996 13,992

4898 9,796

2799 5,598

13992 2,868,360

-

1540 303,380

2099 16,792

-



4478 1,020,984

5247 10,494

6297 138,534

3498 6,996



6297 100,752

10494 20,988

-

5422 1,453,096

8081 32,324

-

20988 146,916



11894 95,152

20988 314,820

20988 41,976

13992 27,984

-

21758 87,032

14762 2,568,588



13992 27,984

16791 33,582

20988 83,952

3498 34,980

-

1680 307,440

1260 120,960

1400 5,600

630 43,470

630 114,030

1400 33,600



-

10494 209,880

2239 434,366

1889 217,235

11894 118,940

350 136,150

1085 648,830

1120 24,640

231 131,208



48972 195,888

1141 11,410

1540 30,800

2344 23,440

-

-

231 911,295

259 1,036



-

196 784

224 612,640

343 945,308

441 563,598

714 121,380

1260 2,520

-

1120 2,240

1400 1,162,000

2729 185,572

3848 126,984

6017 150,425

-

3673 3,673

4128 8,256

-

5317 5,317

4828 9,656

-

8857 8,857

9935 19,870



-

840 4,200

1295 9,065

2099 20,990

-

15671 94,026

18190 1,346,060

21688 585,576

-

14692 14,692

16091 32,182

-

3498 76,956

-

13992 41,976



4198 847,996

20988 83,952

140 83,440

168 17,304

490 1,132,390

679 3,288,397

1225 2,156,000 -

280 183,680

455 91,000

644 748,328

1190 935,340



-

420 309,540

595 61,285

1120 1,086,400

910 577,850

-

1050 4,200

3498 97,944



224 56,448

343 137,543

441 156,555

714 299,880

1260 432,180

1610 552,230

2239 22,390

-

1330 803,320

1924 706,108 -

1924 1,165,944 -



-

2099 69,267

-

-

16791 638,058

27984 531,696

48972 195,888

-

13992 853,512

-



-

11894 404,396

13992 2,392,632

-

20289 4,159,245

770 47,740

1050 51,450

1400 67,200 1680 15,120

2099 4,198

20988 125,928



1051856 1,051,856

-

-

-

-

-

191899 959,495

-



-

-

-

-

-

-

-

-

-

-

104940 209,880

-

-

- -

-



349798 349,798



1972776 1,972,776

580916 580,916

-



-



10100446 10,100,446



3358056 3,358,056



1403 11,939,530

1259 1,535,980



1465 4,395,000

1244 597,120



2637 3,533,580

8322 2,871,090

3749 2,174,420



5254 966,736

3665 776,980

825 61,050

1991 284,713



2213 2,637,896

3017 241,360

2261 165,053



2433 498,765



5651 2,119,125

5576 11,152

3014 18,084

1281 23,058



1507 678,150

203 93,380

193 2,165,460

330 1,260,600

490 98,000



317 1,287,337

422 373,470

308 30,800

263 526,000

1928 3,092,512



1082 4,251,178

3413 1,433,460



1397 474,980

159 12,043,614

144 7,200

178 13,482,788

189 350,595



362 881,108

3222 7,842,348



283 471,195

1087 1,809,855



1262 2,419,254



4605 12,479,550

3837 1,438,875

654 1,412,640

1330 1,263,500

2907 2,354,670



1199 5,995

-

3633 18,165

3052 15,260

3488 52,320

4264 2,686,320



3488 3,313,600

8602 10,322,400

6009 60,090

-

-

8719 43,595

18890 188,900



1977 796,731

-

-

12351 17,908,950



-

-

10210 408,400

12924 245,556

-



8644 1,849,816

-



6441 1,494,312

155732 311,464

153877 1,077,139

10514 1,461,446

-



1685 1,090,195

1650 627,000

982 3,019,650

947 33,145

-

6600 1,709,400

9164 9,704,676

-

223 885,310

-

-



-

-

-

11492 2,930,460

9426 254,502

11822 2,435,332

11767 353,010

17229 482,412

-



357 857,871

357 429,114

1678 16,780

4376 1,115,880

2056 557,176

1408 5,632

8505 1,794,555

8763 105,156

10524 505,152

22622 2,171,712

7337 29,348

745 195,935

14035 2,666,650

968 968

974 723,682

239 10,994

490 292,530

31363 4,955,354

33686 1,246,382

8170 32,680

-

3744 14,976

2771 268,787

674 359,242

2246 327,916

250 25,500



869 88,638

31095 357,593

4214 695,310

-

1962 29,430

2616 1,216,440



1163 1,309,538

1233 573,345

2616 26,160

1956 39,120

-

16812 50,436

12976 12,976

11065 33,195

3306 310,764



-

-

1170 983,970

1452 2,904

-

-

-



-

-

-

-

7228 433,680

1956 332,520

2180 10,900

-

197 265,950

218 1,417,000

5783 23,132

9881 29,643

6539 228,865



1109 96,483

2398 990,374

9366 18,732

33143 5,634,310



37215 1,414,170

15986 1,598,600

9695 969,500



13327 79,962

41223 618,345

13513 337,825

74867 224,601



73536 73,536

5574 78,036

74867 224,601

111301 111,301

27451 54,902

1236 24,720

800 16,000



94273 565,638

100232 1,002,320



276228 1,657,368

69683 1,323,977

62010 3,286,530

54174 2,112,786

13350 106,800



49126 1,375,528

68974 137,948



23740 4,391,900

26617 266,170

30927 154,635

34675 69,350



45108 90,216

47686 95,372

77917 5,687,941

26675 106,700



49657 148,971

241120 482,240 241120 241,120

8962 44,810

1608 8,040

6813 34,065



24065 144,390

126560 8,099,840

41180 2,635,520

23950 1,532,800

59025 7,555,200

69158 1,936,424



41798 83,596

70981 851,772

17657 1,165,362

-

-

126560 506,240

41180 82,360

23950 47,900

59025 236,100

17657 35,314

54870 109,740

86194 172,388



113492 7,490,472



778589 49,829,696



330922 9,265,816

589555 589,555



935149 1,870,298



23901 2,007,684



16761 5,665,218

50849 2,593,299

10645 766,440

4496 107,904

-

40032 640,512

53882 1,077,640



-

9852 147,780

11537 80,759

12528 28,814,400

4078 20,390



8206 41,030

8335 941,855

3263 2,251,470

-

-



33717 14,329,725

31271 156,355

-

32086 3,529,460



29640 148,200

60683 788,879

-

-

23131 231,310

23131 462,620



-

23637 118,185

23637 283,644

-

8206 1,395,020

8206 12,596,210

-



13018 911,260

9723 2,479,365

8695 86,950

-

5058 7,587,000



-

5220 30,145,500

816 1,248,480

-

607 482,565

7748 813,540



8972 89,720

-

12234 19,574,400

12234 122,340

-

8483 254,490

9298 92,980

6613 66,130



3263 1,288,885

3263 326,300

1034 51,700



10815 216,300

6269 313,450

509736 2,038,944



1391441 1,391,441

7494493 7,494,493

1859847 3,719,694

1261000 1,261,000



1787500 1,787,500

2043682 4,087,364

970 97,000

-

16060 16,060

11149 66,894

46930 2,815,800



43703 2,884,398

41358 992,592

268195 268,195

32500 32,500

32500 32,500

26000 26,000

13000 13,000

13000 13,000

32500 32,500

13000 13,000

-

-



-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-



-

-

-

-

-

-

-

6015642 6,015,642

-

-

-

-



-

-

-

-

-

-

891745 1,783,490

-

-

-

-

-

- -

-

292750 292,750

-

-

-

-



-

-

-

-

-

-

759268 759,268

-

-

-

-

-

-

-

-

-

-

276819 276,819

-

-

-

-

-

-



-

-

225129 225,129

-

-

-

-

-

-

-

-

223829 223,829

-

-

-

- -

-

-

-



-

189368 189,368

-

-

-

-

-

- -

-

222529 222,529

-

-

-

-

-

-

-

-



223829 895,316

-

-

-

-

-

-

-

-

223829 2,909,777

-

-

-

-

-

-

-

241059 482,118



-

-

-

-

-

-

-

-

223829 223,829

-

-

-

-

-

-

-

223829 2,238,290

-



-

-

-

-

-

-

188068 188,068

-

-

-

-

-

-

-

-

126461 505,844

-

-

-

-

-

-



-

-

188068 188,068

-

-

-

- -

-

-

-

164823 164,823

-

-

-

-

- -

-

-



-

400032 400,032

-

-

-

-

-

-

-

-

281988 281,988

-

-

-

-

-

-

-

-



188068 188,068

-

-

-

-

-

-

-

300065 300,065

-

-

-

-

-

-

-

-

-

301365 301,365



-

-

-

-

-

-

-

215214 215,214

-

-

-

-

- -

-

-

-

197984 197,984

-



80786 161,572

-

-

21977 1,208,735

-

-

13036 104,288



-

-

-

-

-

-

-

-

-

-

-

21519 1,312,659

-

-

-

-

-



-

23872 143,232

-

-

-

-

-

-

27278 1,964,016

-

-

-

-

31017 62,034

-

-

-

-

-

-



25015 175,105

-

-

-

-

-

-

22660 45,320

-

-

-

-

-

-

37718 113,154

-

-

-

-

-



-

35460 141,840

-

-

-

-

-

31017 31,017

-

-

-

-

-

-

32588 97,764

-

-

-

-

-

-



27550 220,400

-

-

-

-

-

-

25015 25,015

-

-

-

-

-

-

22660 67,980

-

-

-

-

-



37526 37,526

-

-

-

-

-

25804 25,804

- -

-

-

-

5186 191,882

-

-

-

-

22429 89,716

-

-



-

-

23754 712,620

59684 119,368

2014 4,028

917 18,340

15513 15,513

15513 93,078

-

23754 498,834

59749 59,749

2079 2,079

982 13,748 15578 77,890

-

27028 973,008

67820 67,820

2547 2,547

1112 26,688

15708 219,912

-



31775 3,622,350

100274 401,096 3015 12,060

1495 113,620

63740 63,740

50504 50,504

28093 28,093

21405 449,505

15448 30,896

-

-

-

7452 819,720

5322 478,980

-

1468 954,200

785 667,250



2124 165,672

53 254,400

213 1,001,100

69 20,700

83 240,700

247 518,700

-

1590 795,000



-

884 2,824,380

463 570,416

133 1,263,500

69 324,300

166 1,826,000

677 119,152

384 176,640

634 174,350

1664 16,640



384 21,120

302 122,008

463 885,256

1433 117,506

348 87,000

450 79,650

2016 963,648

4919 108,218

4854 43,686

2748 54,960

7092 156,024

17727 159,543

26000 26,000



26000 78,000

20092 100,460

81 810

564 2,256

1299 5,196

81 810

294 119,364

1192 21,456

199 14,925

296 50,024

1104 8,832

191 1,910

302 170,328

1442 50,470

341 64,790

605 330,330

1416 36,816



311 32,655

1130 6,780

372 212,784

-

-

124 12,400

144 547,200

195 9,750

421 21,050 55 5,500

64 6,400

86 60,200

109 10,900

-

984 334,560

135 18,360

1370 164,400

170 8,160

2362 472,400

251 20,080



705 52,875

108 3,240

842 21,050

139 1,390

-

-

-

-

7042 7,042

-

-



-

-

1499 89,940

2105 52,625

3225 80,625

3566 142,640

4321 86,420

-

-

-

-

5221 26,105

6643 13,286

7563 37,815

9234 9,234

-

848 27,136

1152 36,864

9022 36,088



22 121,000

56 84,000

59 147,500

103 154,500

-

26 182,000

698 27,920

59 147,500

-

-

-



-

1401 3,964,830

1113 445,200

919 827,100

618 33,990

528 16,896

260 702,000

205 153,750 177 513,300

134 509,200

277 886,400

169 16,055

121 955,900

893 392,920

426 276,900

218 196,200

159 36,570

101 2,020

66 21,780

602 60,200

326 32,600

237 11,850

207 517,500 -

2945 106,020

2257 9,028



1932 50,232

1330 5,320

1195 4,780

980 56,840

767 42,952

475 105,450

465 113,460

430 28,380

283 566

273 36,036

780 62,400

650 13,000

390 17,160

260 4,160

195 780

130 4,160

403 1,612

311 1,244

294 1,176

282 22,560

256 6,912

-

-

-



7019 168,456

21230 764,280

277 102,490

144 50,400

545 185,300

99 255,420

3497 524,550

-

-



-

-

1026 410,400

1339 468,650

-

722 649,800

789 39,450

878 702,400

1310 78,600

3900 273,000

1175 11,750

-

-

-

2877 8,631

2175 54,375

234 46,800

368 3,680

4263 42,630

1221 2,442

1713 10,278



300 600

234 1,404

9126 91,260

611 6,110

-

-

-

382 64,940

88 30,800

2012 185,104

-

-



-

67339 6,195,188

-

-

13000 1,196,000

-

31884 956,520

-



-

27061 270,610

127595 5,358,990

31604 126,416

40433 161,732

-

-



-

32971 329,710

-

-

32418 1,037,376

32971 329,710

41846 83,692

-

-



55107 330,642

27061 162,366



1177522 2,355,044

263527 527,054

1056752 1,056,752

219822 219,822



545835 1,091,670

352236 352,236

117845 117,845



468781 937,562

-

-

-

-

166403 499,209

568 255,600



26173 78,519

28672 172,032

547 54,700

10 3,000

-

12440 37,320

-

-

-

-

7000000 7,000,000

-

-

-

-

- -

-

-

-

-

-

-

-



-

-

-

-

-

-

-

2227 659,192

-

-

1806 939,120

-

-

1403 213,256

-

-

1985 214,380

-

- 4930 2,780,520

-

-

4918 127,868

-

-

2872 86,160

-

- 2526 242,496

-

-

5543 16,629

-

-



919 9,190

-

-

2185 17,480

- -

2882 129,690

-

-

919 552,319

-

-

675 58,050

-

- 985 142,825

-

-

6605 99,075

-

-

8450 253,500

-

-

11700 351,000

-

-

-

-

-

-

3312 82,800

-



4363 436,300

17727 177,270

6157 307,850

2019 1,021,614

1629 107,514

4082 983,762

5616 16,848

187 374,000

133 266,000



6916 221,312

3549 1,249,248

2912 652,288

2548 163,072

5187 663,936

2730 174,720

5278 337,792

6552 209,664

3458 1,217,216



3185 713,440

4004 256,256

5187 663,936

2730 174,720

6500 416,000

8372 33,488

12194 97,552

26390 527,800

8736 270,816

6552 39,312

4004 56,056

2730 21,840



5200 52,000

10400 41,600

2860 148,720

15600 109,200

15600 62,400

18200 72,800

20150 80,600

10400 10,400



12651437 25,302,874

-

-

-

1089998 2,179,996



1109652 2,219,304

6773379 6,773,379

-

2074355 2,074,355



4375 218,750

33221 132,884

6459 103,344

9043 542,580

33919 67,838

-

1461 58,440



552 16,560

73051 146,102

21788 43,576

-

1261 126,100 1368 136,800

2755 5,510

127032 1,524,384



-

-

-

-

-

-

-

5182450 10,364,900

3889600 7,779,200



2342600 4,685,200

-

-

-

-

-

5006736 5,006,736



3808750 3,808,750

-

-

-

-

-

2277451 2,277,451

-

-

-

-

26070 234,630 403145 403,145

529458 529,458

219 109,500

-

-



-

-

-

-

-

-

-

-

-

-

-

1200687 1,200,687

-



-

-

-

-

1051002 1,051,002

-

-

-

-

74600 820,600

73181 1,683,163

66843 534,744

65424 1,308,480

63910 1,278,200

60316 1,990,428 59275 3,971,425

-

67316 134,632

60883 974,128

60031 300,155

58991 530,919

-

77721 310,884



-

97682 195,364

152954 152,954

-

134008 268,016

162414 487,242

170833 2,391,662

-

586836 586,836

893522 1,787,044

1121826 1,121,826

1164122 1,164,122

1208627 1,208,627

1363625 1,363,625

1501818 4,505,454

345947 345,947

-

3976 238,560 4638 111,312

6058 333,190

9463 681,336

-

444 310,356



596 203,832

826 756,616

1058 378,764

1138 281,086

1355 453,925

1561 92,099

1694 13,552

2109 297,369 2227 35,632

2323 355,419

2449 313,472

308 539,000

289 309,230

-

487 273,694

308 183,568

-

-

-

-

387572 387,572

294656 294,656

253367 253,367



-

-

131048 262,096

75755 227,265

66097 2,115,104

52992 105,984

- -

224053 672,159

182114 364,228

137967 1,103,736

-

-



-

639933 1,919,799

-

444 94,572

596 75,990

826 248,626

1058 330,096

1138 31,864 1561 455,812

1694 13,552

-

487 50,161

308 34,496

439 187,892

308 73,612



-

667 32,016

838 33,520

1049 2,098

-

-

-

-

-

-

-

2003871 10,019,355

-

1300 565,500

1501 652,935



1047 52,350

320 144,000

45233 226,165

15679 78,395

353746 353,746

5829 373,056

5120 327,680

-

853 46,915

647 7,764

-

3903 19,515

-

- -



-

-

-

2513 30,156

-

644 7,728

-

853 22,178

647 29,115

-

14322 57,288

-

3903 7,806

-

25323 25,323



-

109220 109,220

-

32979 32,979

-

20756 20,756

3552 14,208

2580 10,320

-

1421 1,421

-

-

1764 13,230

1501 327,218

1258 503,829

1127 1,024,443



960 1,699,680

1981 174,328

581 379,393

1060 79,500

-

358 117,066

435 11,745

487 4,627 -

465 101,370

624 11,232

776 4,656

-

2652 29,172

2652 15,912

2652 53,040

2652 74,256



-

2652 84,864

2652 55,692

-

500 12,000

8591 21,478

13624 108,720

-

1204 237,188

1204 57,792

12775 34,493

14064 84,384

8093 48,558

11223 23,568



10987 109,870

11855 1,778

14367 707,575

-

621 308,637

666 477,522

832 54,912

1216 76,608

1729 32,851

-

-

614334 1,228,668

-

-

-

448628 897,256

- -

-

175142 175,142

-

-

-

184717 184,717

-



-

-

132162 132,162

-

-

-

68202 136,404

- -

-

68202 68,202

-

-

-

35389 35,389

-

-

-

35389 35,389 -

-

-

35389 35,389

-

-

-

40499 80,998

-

-

-

40499 80,998 -

-

-

45549 91,098

-

-

-

45549 45,549

-

-

- 45549 136,647

-

-

-

47119 47,119

-

-

-



47119 47,119

-

-

-

56685 56,685

-

-

- 56685 56,685

-

-

-

117664 117,664

-

-

-

177902 711,608

-

- -

-

24766 24,766 -

-

-

21101 21,101

-

-

-

-

6482 12,964

-

-



-

18125 54,375

-

-

-

14183 936,078

-

- -

10715 300,020

-

-

-

8928 1,687,392

-

-

-

-

56830 113,660

- -

-

48993 97,986

-

-

-

219 536,550

-

-

-



48667 340,669

-

-

58814 117,628

-

-

58814 58,814

-

-

53784 107,568

-

-



66673 133,346

-

-

706 31,770

501 42,585

2088 41,760

-

632 2,528

592 5,920

2964 11,856

230 3,220

9342 2,924,046

-

-

-

1987 317,920

-

-



911625 911,625

-

663000 1,326,000

-

143650 143,650

-

-

-



193375 193,375

-

193375 193,375

-

-

155 4,650

188 5,640

243 7,290

-

-

66 132



99 198

133 798

-

0 -

-

99450 198,900

35360 176,800

21548 538,700

15470 30,940

14365 14,365

-

7293 116,688

6188 24,752

5525 77,350

4420 30,940

-

7735 85,085

6630 324,870

884 6,188

-

66300 66,300

39780 636,480

13260 39,780

11050 44,200

-

4641 2,691,780

2873 3,441,854



1492 55,204

-

13260 119,340

8840 35,360

4641 88,179

2873 499,902

1989 354,042

1492 56,696

1216 113,088

995 72,635

718 22,258 5967 155,142

4973 129,298

6630 172,380

15470 324,870

6078 328,212



19890 1,491,750

13260 994,500

13260 729,300

19890 258,570

398 384,070

-

1105 28,730

11050 11,050



60775 425,425

-

-

2763 975,339

1989 244,647

1547 595,595 1105 651,950

939 1,422,585

718 250,582

635 539,115

475 1,729,950

-

7293 145,860

6188 24,752

5746 109,174

5525 33,150 4420 17,680

-

7735 247,520

6630 106,080

884 6,188

1989 17,901

387 268,191



387 359,910

442 304,980

-

5525 38,675

5525 11,050

5525 88,400

4420 13,260

-

1768 1,207,544

122 1,077,626

66300 66,300

55250 55,250

- -

6630 676,260

-

-

-

2873 356,252

-



-

-

3315 66,300

-

-

-

1989 9,945

-

-

-

-

638394 638,394

566965 566,965

275655 826,965

-

3429 1,947,672

4016 3,080,272

12484 249,680

10452 1,003,392



4755 513,540

3478 274,762

4458 106,992

3182 79,550

162 55,404

135 2,160,000

73024 292,096

130 1,300,000

135722 135,722

-

-

296032 296,032

79180 79,180

2617 81,127



1565 29,735

1132 328,280

35423 106,269

19945 119,670

120 1,500,000

7330 7,330

9212 9,212

32680 32,680

50242 50,242

-

-

-

-

36134 505,876

36853 331,677

72270 72,270

72270 289,080

108405 108,405

6939 499,608

68960 68,960 3744 67,392

6649 66,490

489 18,582

1151 32,228

-

187 495,550



260 1,638,000

130 260,000

99361 99,361

466 233,000

547715 547,715

-

289801 1,159,204

278226 556,452

264751 1,323,755

264751 1,059,004

-

324641 2,272,487

486604 486,604

753514 753,514



59936 2,157,696

27350 547,000

1151 230,200

-

-

14525 174,300

23826 190,608

119780 119,780

96456 1,543,296

1151 23,020

5470 92,990

123570 494,280

-

114 1,436,400

128 640,000

22168 487,696

4895 14,685



360 1,800,000

-

43118 1,552,248

309669 309,669

3026252 3,026,252

79180 316,720

1151 92,080

17994 71,976

2488 19,904

-

-

118554 711,324

3715 2,043,250

85664 85,664

36249 217,494

30529 183,174

4970 69,580 67650 67,650

17994 215,928

146065 146,065

54702 54,702



2880 2,880

2880 2,880

-

-

685292 685,292

44627 44,627

132 33,000

2017 48,408

2017 48,408

132446 132,446

223137 223,137

3744 3,744

130 32,500

63341 63,341

-

-

23033 23,033

2017 24,204

130 19,500

-

-

59010 59,010

14109 84,654

979 5,874

3744 3,744



183 27,450

-

-

-

532656 532,656

-

339754 339,754

-

1362335 1,362,335

-

97893 391,572

27350 27,350

22168 22,168

-



-

94297 94,297

157161 157,161

157161 157,161

31433 31,433

31433 31,433

31433 31,433

31433 31,433

282893 282,893

-

18500 37,000

-

3377 13,508

25088 25,088

22315 22,315

520449 520,449

13261 26,522

-

3377 6,754

7181 21,543

2488 7,464

16740 16,740

3068 9,204

38582 38,582

-



1497 5,988

3068 21,476

16645 16,645

38582 38,582

3377 3,377

8460 8,460

-

109 763,000

114 228,000

171 85,500

130 364,000

1123 1,965,250

1522 1,522,000

1165 128,150

1,728,888,475

Grand Total 1,730,124,013

2% 34,602,480

fter rebate 1,695,521,533

Boq Tnhb Ongc Chennai

Documents

Transcript of Boq Tnhb Ongc Chennai