Table of Factors and Terms For Bending Formulas

B = degree of bendE = feathered edge thicknessFb= bend difficulty factorFd= "D" of bendFw= wall factorKr= constant for rigidityKs= constant for minimum clamp lengthKz= constant for feathered edgeLc= clamp lengthLp= pressure die lengthMb= mandrel ball diameterMd= mandrel nose diameterMm= mandrel body diameterMr= mandrel nose radiusPe= percentage of elongation at arcPt= percentage of wall-thinningPw= wall thickness after thinningR = centerline radiusRi= inside radiusRo= outside radiusS = maximum set-up depthT = tube outside diameterTi= tube inside diameterW = wall thicknessWi= thickness of inside laminationWo= thickness of outside lamination

Tube inside diameter:Ti= T - ( W x 2 )

Inside radius:Ri= R - ( T / 2 )

Outside radius:Ro= R + ( T / 2 )

Wall factor:Fw= T / W

"D" of bend:Fd= R / T

Bend difficulty rating(the higher the value, the more difficult the bend is to make; rule of thumb only):Where "Kr" = a constant for material rigidity (assign the same value to "Kr" as you would to calculate pressure die length; a value of 2 is suitable for most applications; click here for more information) and "n1" through "n4" are values to adjust the weight of each factor in the equation (see below for our recommended weighting):General formula:Fb= [ ( n1x Kr) + ( n2x Fw) + ( ( n3x B ) / 180 ) ) ] / [ n4x Fd]Formula with recommended weighting:Fb= [ 2Kr+ .2Fw+ ( B / 180 ) ] / [ Fd]Note: A bend difficulty rating (calculated with our recommended weighting) of 7 or less indicates a bend that is relatively simple to produce with the rotary-draw method. Factors in excess of 7 typically require either additional precision in set-up or close attention during production in order to hold the set-up parameters.

Wall-thinning of extrados at outside radius after bending(rule of thumb only):Where "Pt" = percentage of wall-thinning and "Pw" = targeted thickness of wall after thinning out from bending:Pt= ( Ro- R ) / RoPw= W x ( 1 - Pt)

Percentage of elongation at arc of the bend(rule of thumb only):Pe= ( Ro/ R ) - 1

Mandrel nose diameterfor single-wall tubing:Md= T - ( W x 2.21 )

Mandrel nose diameter for double-wall tubing:Where "Wo" = wall thickness of outside lamination and "Wi" = wall thickness of inside lamination:Md= ( T - ( Wox 2 ) ) - ( Wix 2.21 )

Mandrel nose radius:if Fw< 50 then Mr= Mdx .1 else Mr= Mdx .02

Mandrel body diameter:Mm= Mdx .995

Mandrel ball diameter:Mb= Mdx .998

Maximum set-up depth of mandrel noserelative to the line of tangency, as measured from nose end(including nose radius):S = [ ( R + ( T / 2) - W )2- ( R + ( Md/ 2 ) )2]1/2+ Mr

Wiper feathered edge thickness (simple-sweep geometry only):Where "Kz" = a constant approaching zero depending upon limitations of material and method of manufacturing (with current technology, a value of .0025 is reasonable for "Kz"):if T x Kz> .006* then E = T x Kzelse E = .006** Inches. For metric applications, substitute .15 millimeters.

Clamp length:Where "Kr" = a constant for material rigidity (assign a value of 2 to "Kr" for most applications; click here for more information) and "Ks" = a constant limiting the minimum clamp length depending upon the surface of the cavity (assign to "Ks" the value of 2 for smooth cavities and 1 for serrated cavities; click here for more information):if ( T x ( Krx 2.5) ) - R < T x Ksthen Lc= T x Kselse Lc= ( T x ( Krx 2.5) ) - R

Pressure die length:Where "Kr" = a constant for material rigidity (assign a value of 2 to "Kr" for most applications; click here for more information):Lp= ( R x 3.14 x ( B / 180 ) ) + ( T x Kr)

Springback and radial growth:We are frequently asked for formulas to calculatespringbackandradial growth. While there are rules of thumb -- e.g., a radius will increase 1% for every "D" of bend -- they are not effective, as a true formula would be, in reducing the prove-out needed to lock in the parameters of a machine set-up.Unfortunately, effective formulas for springback and radial growth have not been developed, because the factors involved include not only tube and bend specifications but also machine settings -- especially the radial pressure and axial pressure applied by the pressure die to the tube and the placement of the mandrel nose relative to the line of tangency. How an operator sets these things on a particular make and model of machine alters where theneutral axisof a tube bend lies in relationship to the centerline of the radius, and it is the location of the neutral axis that determines how much springback and radial growth there will be. Moreover, springback and radial growth are the result of fundamentally non-linear processes, which would make any effective formula that does account for all these factors fairly complex. Presently, finite element analysis (FEA) is the only tool up to this task, and it is not yet practical for everyday use in the bend shop.Fortunately, the trial-and-error needed to adjust for springback and radial growth does not have to be repeated for every set-up of a tube bend. By using the"Four-Step Set-Up Method"to employ the "forward mandrel, low pressure" set-up for rotary-draw tube-bending, the parameters of a successful set-up can be recorded and then duplicated with little or no trial-and-error to prove out future set-ups of the same or similar tube bends.